The RFC 4884 spec is largely the same between IPv4 and IPv6.
Factor out the IPv4 specific parts in preparation for IPv6 support:
- icmp types supported
- icmp header size, and thus offset to original datagram start
- datagram length field offset in icmp(6)hdr.
- datagram length field word size: 4B for IPv4, 8B for IPv6.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Only accept packets with original datagram len field >= header len.
The extension header must start after the original datagram headers.
The embedded datagram len field is compared against the 128B minimum
stipulated by RFC 4884. It is unlikely that headers extend beyond
this. But as we know the exact header length, check explicitly.
2) Remove the check that datagram length must be <= 576B.
This is a send constraint. There is no value in testing this on rx.
Within private networks it may be known safe to send larger packets.
Process these packets.
This test was also too lax. It compared original datagram length
rather than entire icmp packet length. The stand-alone fix would be:
- if (hlen + skb->len > 576)
+ if (-skb_network_offset(skb) + skb->len > 576)
Fixes: eba75c587e ("icmp: support rfc 4884")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable status is being initialized with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed. Also put the variable declarations into
reverse christmas tree order.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patch introduced a deadlock, this patch fixes it by making
sure the work is canceled without holding the global ovs lock. This is
done by moving the reorder processing one layer up to the netns level.
Fixes: eac87c413b ("net: openvswitch: reorder masks array based on usage")
Reported-by: syzbot+2c4ff3614695f75ce26c@syzkaller.appspotmail.com
Reported-by: syzbot+bad6507e5db05017b008@syzkaller.appspotmail.com
Reviewed-by: Paolo <pabeni@redhat.com>
Signed-off-by: Eelco Chaudron <echaudro@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This sockopt accepts two kinds of parameters, using struct
sctp_sack_info and struct sctp_assoc_value. The mentioned commit didn't
notice an implicit cast from the smaller (latter) struct to the bigger
one (former) when copying the data from the user space, which now leads
to an attempt to write beyond the buffer (because it assumes the storing
buffer is bigger than the parameter itself).
Fix it by allocating a sctp_sack_info on stack and filling it out based
on the small struct for the compat case.
Changelog stole from an earlier patch from Marcelo Ricardo Leitner.
Fixes: ebb25defdc ("sctp: pass a kernel pointer to sctp_setsockopt_delayed_ack")
Reported-by: syzbot+0e4699d000d8b874d8dc@syzkaller.appspotmail.com
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For architectures like x86 and arm64 we don't need the separate bit to
indicate that a pointer is a kernel pointer as the address spaces are
unified. That way the sockptr_t can be reduced to a union of two
pointers, which leads to nicer calling conventions.
The only caveat is that we need to check that users don't pass in kernel
address and thus gain access to kernel memory. Thus the USER_SOCKPTR
helper is replaced with a init_user_sockptr function that does this check
and returns an error if it fails.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework the remaining setsockopt code to pass a sockptr_t instead of a
plain user pointer. This removes the last remaining set_fs(KERNEL_DS)
outside of architecture specific code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org> [ieee802154]
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factour out a helper to set the IPv6 option headers from
do_ipv6_setsockopt.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Note that the get case is pretty weird in that it actually copies data
back to userspace from setsockopt.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split ipv6_flowlabel_opt into a subfunction for each action and a small
wrapper.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is mostly to prepare for cleaning up the callers, as bpfilter by
design can't handle kernel pointers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bpfilter user mode helper processes the optval address using
process_vm_readv. Don't send it kernel addresses fed under
set_fs(KERNEL_DS) as that won't work.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split __bpfilter_process_sockopt into a low-level send request routine and
the actual setsockopt hook to split the init time ping from the actual
setsockopt processing.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __user doesn't make sense when casting to an integer type, just
switch to a uintptr_t cast which also removes the need for the __force.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding new cls flower keys for hash value and hash
mask and dissect the hash info from the skb into
the flow key towards flow classication.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Retreive a hash value from the SKB and store it
in the dissector key for future matching.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I noticed that touching linux/rhashtable.h causes lib/vsprintf.c to
be rebuilt. This dependency came through a bogus inclusion in the
file net/flow_offload.h. This patch moves it to the right place.
This patch also removes a lingering rhashtable inclusion in cls_api
created by the same commit.
Fixes: 4e481908c5 ("flow_offload: move tc indirect block to...")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Braino when converting "buf->len -=" to "buf->len = len -".
The result is under-estimation of the ralign and rslack values. On
krb5p mounts, this has caused READDIR to fail with EIO, and KASAN
splats when decoding READLINK replies.
As a result of fixing this oversight, the gss_unwrap method now
returns a buf->len that can be shorter than priv_len for small
RPC messages. The additional adjustment done in unwrap_priv_data()
can underflow buf->len. This causes the nfsd_request_too_large
check to fail during some NFSv3 operations.
Reported-by: Marian Rainer-Harbach
Reported-by: Pierre Sauter <pierre.sauter@stwm.de>
BugLink: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1886277
Fixes: 31c9590ae4 ("SUNRPC: Add "@len" parameter to gss_unwrap()")
Reviewed-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for net:
1) Fix NAT hook deletion when table is dormant, from Florian Westphal.
2) Fix IPVS sync stalls, from guodeqing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The purpose of this override is to give the user an indication of what
the number of the CPU port is (in DSA, the CPU port is a hardware
implementation detail and not a network interface capable of traffic).
However, it has always failed (by design) at providing this information
to the user in a reliable fashion.
Prior to commit 3369afba1e ("net: Call into DSA netdevice_ops
wrappers"), the behavior was to only override this callback if it was
not provided by the DSA master.
That was its first failure: if the DSA master itself was a DSA port or a
switchdev, then the user would not see the number of the CPU port in
/sys/class/net/eth0/phys_port_name, but the number of the DSA master
port within its respective physical switch.
But that was actually ok in a way. The commit mentioned above changed
that behavior, and now overrides the master's ndo_get_phys_port_name
unconditionally. That comes with problems of its own, which are worse in
a way.
The idea is that it's typical for switchdev users to have udev rules for
consistent interface naming. These are based, among other things, on
the phys_port_name attribute. If we let the DSA switch at the bottom
to start randomly overriding ndo_get_phys_port_name with its own CPU
port, we basically lose any predictability in interface naming, or even
uniqueness, for that matter.
So, there are reasons to let DSA override the master's callback (to
provide a consistent interface, a number which has a clear meaning and
must not be interpreted according to context), and there are reasons to
not let DSA override it (it breaks udev matching for the DSA master).
But, there is an alternative method for users to retrieve the number of
the CPU port of each DSA switch in the system:
$ devlink port
pci/0000:00:00.5/0: type eth netdev swp0 flavour physical port 0
pci/0000:00:00.5/2: type eth netdev swp2 flavour physical port 2
pci/0000:00:00.5/4: type notset flavour cpu port 4
spi/spi2.0/0: type eth netdev sw0p0 flavour physical port 0
spi/spi2.0/1: type eth netdev sw0p1 flavour physical port 1
spi/spi2.0/2: type eth netdev sw0p2 flavour physical port 2
spi/spi2.0/4: type notset flavour cpu port 4
spi/spi2.1/0: type eth netdev sw1p0 flavour physical port 0
spi/spi2.1/1: type eth netdev sw1p1 flavour physical port 1
spi/spi2.1/2: type eth netdev sw1p2 flavour physical port 2
spi/spi2.1/3: type eth netdev sw1p3 flavour physical port 3
spi/spi2.1/4: type notset flavour cpu port 4
So remove this duplicated, unreliable and troublesome method. From this
patch on, the phys_port_name attribute of the DSA master will only
contain information about itself (if at all). If the users need reliable
information about the CPU port they're probably using devlink anyway.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously TLP may send multiple probes of new data in one
flight. This happens when the sender is cwnd limited. After the
initial TLP containing new data is sent, the sender receives another
ACK that acks partial inflight. It may re-arm another TLP timer
to send more, if no further ACK returns before the next TLP timeout
(PTO) expires. The sender may send in theory a large amount of TLP
until send queue is depleted. This only happens if the sender sees
such irregular uncommon ACK pattern. But it is generally undesirable
behavior during congestion especially.
The original TLP design restrict only one TLP probe per inflight as
published in "Reducing Web Latency: the Virtue of Gentle Aggression",
SIGCOMM 2013. This patch changes TLP to send at most one probe
per inflight.
Note that if the sender is app-limited, TLP retransmits old data
and did not have this issue.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We recently added some bounds checking in ax25_connect() and
ax25_sendmsg() and we so we removed the AX25_MAX_DIGIS checks because
they were no longer required.
Unfortunately, I believe they are required to prevent integer overflows
so I have added them back.
Fixes: 8885bb0621 ("AX.25: Prevent out-of-bounds read in ax25_sendmsg()")
Fixes: 2f2a7ffad5 ("AX.25: Fix out-of-bounds read in ax25_connect()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Passing "sizeof(struct blah)" in kzalloc calls is less readable,
potentially prone to future bugs if the type of the pointer is changed,
and triggers checkpatch warnings.
Tweak the kzalloc calls in l2tp which use this form to avoid the
warning.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When creating an L2TP tunnel using the netlink API, userspace must
either pass a socket FD for the tunnel to use (for managed tunnels),
or specify the tunnel source/destination address (for unmanaged
tunnels).
Since source/destination addresses may be AF_INET or AF_INET6, the l2tp
netlink code has conditionally compiled blocks to support IPv6.
Rather than embedding these directly into l2tp_nl_cmd_tunnel_create
(where it makes the code difficult to read and confuses checkpatch to
boot) split the handling of address-related attributes into a separate
function.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
l2tp_nl_tunnel_send has conditionally compiled code to support AF_INET6,
which makes the code difficult to follow and triggers checkpatch
warnings.
Split the code out into functions to handle the AF_INET v.s. AF_INET6
cases, which both improves readability and resolves the checkpatch
warnings.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpatch warns about indentation and brace balancing around the
conditionally compiled code for AF_INET6 support in
l2tp_dfs_seq_tunnel_show.
By adding another check on the socket address type we can make the code
more readable while removing the checkpatch warning.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These checks are all simple and don't benefit from extra braces to
clarify intent. Remove them for easier-reading code.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpatch warns about comparisons to NULL, e.g.
CHECK: Comparison to NULL could be written "!rt"
#474: FILE: net/l2tp/l2tp_ip.c:474:
+ if (rt == NULL) {
These sort of comparisons are generally clearer and more readable
the way checkpatch suggests, so update l2tp accordingly.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use eth_zero_addr() to clear mac address insetad of memset().
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So that we can easily perform some basic PM-related
adimission checks before creating the child socket.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Tested-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_send_active_reset() is more prone to transient errors
(memory allocation or xmit queue full): in stress conditions
the kernel may drop the egress packet, and the client will be
stuck.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Tested-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When syncookie are in use, the TCP stack may feed into
subflow_syn_recv_sock() plain TCP request sockets. We can't
access mptcp_subflow_request_sock-specific fields on such
sockets. Explicitly check the rsk ops to do safe accesses.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Tested-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mentioned function has several unneeded branches,
handle each case - MP_CAPABLE, MP_JOIN, fallback -
under a single conditional and drop quite a bit of
duplicate code.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Tested-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently accepted msk sockets become established only after
accept() returns the new sk to user-space.
As MP_JOIN request are refused as per RFC spec on non fully
established socket, the above causes mp_join self-tests
instabilities.
This change lets the msk entering the established status
as soon as it receives the 3rd ack and propagates the first
subflow fully established status on the msk socket.
Finally we can change the subflow acceptance condition to
take in account both the sock state and the msk fully
established flag.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Tested-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the unlikely event of a failure at connect time,
we currently clear the request_mptcp flag - so that
the MPC handshake is not started at all, but the msk
is not explicitly marked as fallback.
This would lead to later insertion of wrong DSS options
in the xmitted packets, in violation of RFC specs and
possibly fooling the peer.
Fixes: e1ff9e82e2 ("net: mptcp: improve fallback to TCP")
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Tested-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When updating a partially acked data fragment, we
actually corrupt it. This is irrelevant till we send
data on a single subflow, as retransmitted data, if
any are discarded by the peer as duplicate, but it
will cause data corruption as soon as we will start
creating non backup subflows.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Tested-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we do not init the subflow write sequence for
MP_JOIN subflows. This will cause bad mapping being
generated as soon as we will use non backup subflow.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Tested-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpatch warned about the L2TP_SKB_CB macro's use of its argument: add
braces to avoid the problem.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In l2tp_core.c both l2tp_tunnel_create and l2tp_session_create take
quite a number of arguments and have a correspondingly long prototype.
This is both quite difficult to scan visually, and triggers checkpatch
warnings.
Add a line break to make these function prototypes more readable.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpatch warns about use of seq_printf where seq_puts would do.
Modify l2tp_debugfs accordingly.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use BIT(x) rather than (1<<x), reported by checkpatch.pl.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported by checkpatch:
"WARNING: function definition argument 'struct sock *'
should also have an identifier name"
Add an identifier name to help document the prototype.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
l2tp_core has conditionally compiled code in l2tp_xmit_skb for IPv6
support. The structure of this code triggered a checkpatch warning
due to incorrect indentation.
Fix up the indentation to address the checkpatch warning.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arguments should be aligned with the function call open parenthesis as
per checkpatch. Tweak some function calls which were not aligned
correctly.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some l2tp code had line breaks which made the code more difficult to
read. These were originally motivated by the 80-character line width
coding guidelines, but were actually a negative from the perspective of
trying to follow the code.
Remove these linebreaks for clearer code, even if we do exceed 80
characters in width in some places.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify some l2tp comments to better adhere to kernel coding style, as
reported by checkpatch.pl.
Add descriptive comments for the l2tp per-net spinlocks to document
their use.
Fix an incorrect comment in l2tp_recv_common:
RFC2661 section 5.4 states that:
"The LNS controls enabling and disabling of sequence numbers by sending a
data message with or without sequence numbers present at any time during
the life of a session."
l2tp handles this correctly in l2tp_recv_common, but the comment around
the code was incorrect and confusing. Fix up the comment accordingly.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix up various whitespace issues as reported by checkpatch.pl:
* remove spaces around operators where appropriate,
* add missing blank lines following declarations,
* remove multiple blank lines, or trailing blank lines at the end of
functions.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Checks on `addr_len` and `usax->sax25_ndigis` are insufficient.
ax25_sendmsg() can go out of bounds when `usax->sax25_ndigis` equals to 7
or 8. Fix it.
It is safe to remove `usax->sax25_ndigis > AX25_MAX_DIGIS`, since
`addr_len` is guaranteed to be less than or equal to
`sizeof(struct full_sockaddr_ax25)`
Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently devlink instance is searched on all doit() operations.
But it is optionally stored into user_ptr[0]. This requires
rediscovering devlink again doing post_doit().
Few devlink commands related to port shared buffers needs 3 pointers
(devlink, devlink_port, and devlink_sb) while executing doit commands.
Though devlink pointer can be derived from the devlink_port during
post_doit() operation when doit() callback has acquired devlink
instance lock, relying on such scheme to access devlik pointer makes
code very fragile.
Hence, to avoid ambiguity in post_doit() and to avoid searching
devlink instance again, simplify code by always storing devlink
instance in user_ptr[0] and derive devlink_sb pointer in their
respective callback routines.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding a stream with stream reconf, the new stream firstly is in
CLOSED state but new out chunks can still be enqueued. Then once gets
the confirmation from the peer, the state will change to OPEN.
However, if the peer denies, it needs to roll back the stream. But when
doing that, it only sets the stream outcnt back, and the chunks already
in the new stream don't get purged. It caused these chunks can still be
dequeued in sctp_outq_dequeue_data().
As its stream is still in CLOSE, the chunk will be enqueued to the head
again by sctp_outq_head_data(). This chunk will never be sent out, and
the chunks after it can never be dequeued. The assoc will be 'hung' in
a dead loop of sending this chunk.
To fix it, this patch is to purge these chunks already in the new
stream by calling sctp_stream_shrink_out() when failing to do the
addstream reconf.
Fixes: 11ae76e67a ("sctp: implement receiver-side procedures for the Reconf Response Parameter")
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's not necessary to go list_for_each for outq->out_chunk_list
when new outcnt >= old outcnt, as no chunk with higher sid than
new (outcnt - 1) exists in the outqueue.
While at it, also move the list_for_each code in a new function
sctp_stream_shrink_out(), which will be used in the next patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise the 'chain_len' filed will carry random values,
some token creation calls will fail due to excessive chain
length, causing unexpected fallback to TCP.
Fixes: 2c5ebd001d ("mptcp: refactor token container")
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Tested-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Checks on `addr_len` and `fsa->fsa_ax25.sax25_ndigis` are insufficient.
ax25_connect() can go out of bounds when `fsa->fsa_ax25.sax25_ndigis`
equals to 7 or 8. Fix it.
This issue has been reported as a KMSAN uninit-value bug, because in such
a case, ax25_connect() reaches into the uninitialized portion of the
`struct sockaddr_storage` statically allocated in __sys_connect().
It is safe to remove `fsa->fsa_ax25.sax25_ndigis > AX25_MAX_DIGIS` because
`addr_len` is guaranteed to be less than or equal to
`sizeof(struct full_sockaddr_ax25)`.
Reported-by: syzbot+c82752228ed975b0a623@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?id=55ef9d629f3b3d7d70b69558015b63b48d01af66
Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the SIOCOUTQ IOCTL to get the send buffer fill
of a DCCP socket, like UDP and TCP sockets already have.
Regarding the used data field: DCCP uses per packet sequence numbers,
not per byte, so sequence numbers can't be used like in TCP. sk_wmem_queued
is not used by DCCP and always 0, even in test on highly congested paths.
Therefore this uses sk_wmem_alloc like in UDP.
Signed-off-by: Richard Sailer <richard_siegfried@systemli.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to unified Ethernet Switch Device Tree Bindings allow for ethernet-ports as
encapsulating node as well.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The buildbot found a config where the header isn't already implicitly
pulled in, so add an explicit include as well.
Fixes: 8c918ffbba ("net: remove compat_sock_common_{get,set}sockopt")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-07-21
The following pull-request contains BPF updates for your *net-next* tree.
We've added 46 non-merge commits during the last 6 day(s) which contain
a total of 68 files changed, 4929 insertions(+), 526 deletions(-).
The main changes are:
1) Run BPF program on socket lookup, from Jakub.
2) Introduce cpumap, from Lorenzo.
3) s390 JIT fixes, from Ilya.
4) teach riscv JIT to emit compressed insns, from Luke.
5) use build time computed BTF ids in bpf iter, from Yonghong.
====================
Purely independent overlapping changes in both filter.h and xdp.h
Signed-off-by: David S. Miller <davem@davemloft.net>
In pfkey_dump() dplen and splen can both be specified to access the
xfrm_address_t structure out of bounds in__xfrm_state_filter_match()
when it calls addr_match() with the indexes. Return EINVAL if either
are out of range.
Signed-off-by: Mark Salyzyn <salyzyn@android.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: kernel-team@android.com
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
The sync_thread_backup only checks sk_receive_queue is empty or not,
there is a situation which cannot sync the connection entries when
sk_receive_queue is empty and sk_rmem_alloc is larger than sk_rcvbuf,
the sync packets are dropped in __udp_enqueue_schedule_skb, this is
because the packets in reader_queue is not read, so the rmem is
not reclaimed.
Here I add the check of whether the reader_queue of the udp sock is
empty or not to solve this problem.
Fixes: 2276f58ac5 ("udp: use a separate rx queue for packet reception")
Reported-by: zhouxudong <zhouxudong8@huawei.com>
Signed-off-by: guodeqing <geffrey.guo@huawei.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When expire_nodest_conn=1 and a destination is deleted, IPVS does not
expire the existing connections until the next matching incoming packet.
If there are many connection entries from a single client to a single
destination, many packets may get dropped before all the connections are
expired (more likely with lots of UDP traffic). An optimization can be
made where upon deletion of a destination, IPVS queues up delayed work
to immediately expire any connections with a deleted destination. This
ensures any reused source ports from a client (within the IPVS timeouts)
are scheduled to new real servers instead of silently dropped.
Signed-off-by: Andrew Sy Kim <kim.andrewsy@gmail.com>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Constify devlink instance pointer while checking if reload operation is
supported or not.
This helps to review the scope of checks done in reload.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reload operation is enabled or not is already checked by
devlink_reload(). Hence, remove the duplicate check from
devlink_nl_cmd_reload().
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to hold a device global lock when initializing
devlink device fields of a devlink instance which is not yet part of the
devices list.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can't use IS_UDPLITE to replace udp_sk->pcflag when UDPLITE_RECV_CC is
checked.
Fixes: b2bf1e2659 ("[UDP]: Clean up for IS_UDPLITE macro")
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I cat 'tx_timeout' by sysfs, it displays as follows. It's better to
add a newline for easy reading.
root@syzkaller:~# cat /sys/devices/virtual/net/lo/queues/tx-0/tx_timeout
0root@syzkaller:~#
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, SO_REUSEPORT does not work well if connected sockets are in a
UDP reuseport group.
Then reuseport_has_conns() returns true and the result of
reuseport_select_sock() is discarded. Also, unconnected sockets have the
same score, hence only does the first unconnected socket in udp_hslot
always receive all packets sent to unconnected sockets.
So, the result of reuseport_select_sock() should be used for load
balancing.
The noteworthy point is that the unconnected sockets placed after
connected sockets in sock_reuseport.socks will receive more packets than
others because of the algorithm in reuseport_select_sock().
index | connected | reciprocal_scale | result
---------------------------------------------
0 | no | 20% | 40%
1 | no | 20% | 20%
2 | yes | 20% | 0%
3 | no | 20% | 40%
4 | yes | 20% | 0%
If most of the sockets are connected, this can be a problem, but it still
works better than now.
Fixes: acdcecc612 ("udp: correct reuseport selection with connected sockets")
CC: Willem de Bruijn <willemb@google.com>
Reviewed-by: Benjamin Herrenschmidt <benh@amazon.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an unconnected socket in a UDP reuseport group connect()s, has_conns is
set to 1. Then, when a packet is received, udp[46]_lib_lookup2() scans all
sockets in udp_hslot looking for the connected socket with the highest
score.
However, when the number of sockets bound to the port exceeds max_socks,
reuseport_grow() resets has_conns to 0. It can cause udp[46]_lib_lookup2()
to return without scanning all sockets, resulting in that packets sent to
connected sockets may be distributed to unconnected sockets.
Therefore, reuseport_grow() should copy has_conns.
Fixes: acdcecc612 ("udp: correct reuseport selection with connected sockets")
CC: Willem de Bruijn <willemb@google.com>
Reviewed-by: Benjamin Herrenschmidt <benh@amazon.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One additional field btf_id is added to struct
bpf_ctx_arg_aux to store the precomputed btf_ids.
The btf_id is computed at build time with
BTF_ID_LIST or BTF_ID_LIST_GLOBAL macro definitions.
All existing bpf iterators are changed to used
pre-compute btf_ids.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200720163403.1393551-1-yhs@fb.com
tcp and udp bpf_iter can reuse some socket ids in
btf_sock_ids, so make it global.
I put the extern definition in btf_ids.h as a central
place so it can be easily discovered by developers.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200720163402.1393427-1-yhs@fb.com
Currently, socket types (struct tcp_sock, udp_sock, etc.)
used by bpf_skc_to_*() helpers are computed when vmlinux_btf
is first built in the kernel.
Commit 5a2798ab32
("bpf: Add BTF_ID_LIST/BTF_ID/BTF_ID_UNUSED macros")
implemented a mechanism to compute btf_ids at kernel build
time which can simplify kernel implementation and reduce
runtime overhead by removing in-kernel btf_id calculation.
This patch did exactly this, removing in-kernel btf_id
computation and utilizing build-time btf_id computation.
If CONFIG_DEBUG_INFO_BTF is not defined, BTF_ID_LIST will
define an array with size of 5, which is not enough for
btf_sock_ids. So define its own static array if
CONFIG_DEBUG_INFO_BTF is not defined.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200720163358.1393023-1-yhs@fb.com
The generic netlink is initialized far after the netlink protocol
itself at subsys_initcall. The devlink is initialized at the same
level, but after, as shown by a disassembly of the vmlinux:
[ ... ]
374 ffff8000115f22c0 <__initcall_devlink_init4>:
375 ffff8000115f22c4 <__initcall_genl_init4>:
[ ... ]
The function devlink_init() calls genl_register_family() before the
generic netlink subsystem is initialized.
As the generic netlink initcall level is set since 2005, it seems that
was not a problem, but now we have the thermal framework initialized
at the core_initcall level which creates the generic netlink family
and sends a notification which leads to a subtle memory corruption
only detectable when the CONFIG_INIT_ON_ALLOC_DEFAULT_ON option is set
with the earlycon at init time.
The thermal framework needs to be initialized early in order to begin
the mitigation as soon as possible. Moving it to postcore_initcall is
acceptable.
This patch changes the initialization level for the generic netlink
family to the core_initcall and comes after the netlink protocol
initialization.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: David S. Miller <davem@davemloft.net>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Link: https://lore.kernel.org/r/20200715074120.8768-1-daniel.lezcano@linaro.org
We forgot to support the xfrm policy hold queue when
VTI was implemented. This patch adds everything we
need so that we can use the policy hold queue together
with VTI interfaces.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Commit 02288248b0 ("tipc: eliminate gap indicator from ACK messages")
eliminated sending of the 'gap' indicator in regular ACK messages and
only allowed to build NACK message with enabled probe/probe_reply.
However, necessary correction for building NACK message was missed
in tipc_link_timeout() function. This leads to significant delay and
link reset (due to retransmission failure) in lossy environment.
This commit fixes it by setting the 'probe' flag to 'true' when
the receive deferred queue is not empty. As a result, NACK message
will be built to send back to another peer.
Fixes: 02288248b0 ("tipc: eliminate gap indicator from ACK messages")
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fragment packets do defrag in tcf_ct_handle_fragments
will clear the skb->cb which make the qdisc_skb_cb clear
too. So the qdsic_skb_cb should be store before defrag and
restore after that.
It also update the pkt_len after all the
fragments finish the defrag to one packet and make the
following actions counter correct.
Fixes: b57dc7c13e ("net/sched: Introduce action ct")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that DSA supports MTU configuration, undo the effects of commit
8b1efc0f83 ("net: remove MTU limits on a few ether_setup callers") and
let DSA interfaces use the default min_mtu and max_mtu specified by
ether_setup(). This is more important for min_mtu: since DSA is
Ethernet, the minimum MTU is the same as of any other Ethernet
interface, and definitely not zero. For the max_mtu, we have a callback
through which drivers can override that, if they want to.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because kfree_skb already checked NULL skb parameter,
so the additional checks are unnecessary, just remove them.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_put_padto() can fail. So check for return type and return NULL
for skb. Caller checks for skb and acts correctly if it is NULL.
Fixes: 6d6148bc78 ("net: hsr: fix incorrect lsdu size in the tag of HSR frames for small frames")
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a current limit of 1920 registered dmb buffers per ISM device
for smc-d. One link group can contain 255 connections, each connection
is using one dmb buffer. When the connection is closed then the
registered buffer is held in a queue and is reused by the next
connection. When a link group is 'full' then another link group is
created and uses an own buffer pool. The link groups are added to a
list using list_add() which puts a new link group to the first position
in the list.
In the situation that many connections are opened (>1920) and a few of
them stay open while others are closed quickly we end up with at least 8
link groups. For a new connection a matching link group is looked up,
iterating over the list of link groups. The trailing 7 link groups
all have registered dmb buffers which could be reused, while the first
link group has only a few dmb buffers and then hit the 1920 limit.
Because the first link group is not full (255 connection limit not
reached) it is chosen and finally the connection falls back to TCP
because there is no dmb buffer available in this link group.
There are multiple ways to fix that: using list_add_tail() allows
to scan older link groups first for free buffers which ensures that
buffers are reused first. This fixes the problem for smc-r link groups
as well. For smc-d there is an even better way to address this problem
because smc-d does not have the 255 connections per link group limit.
So fix the problem for smc-d by allowing large link groups.
Fixes: c6ba7c9ba4 ("net/smc: add base infrastructure for SMC-D and ISM")
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To get a send slot smc_wr_tx_get_free_slot() is called, which might
wait for a free slot. When smc_wr_tx_get_free_slot() returns there is a
check if the connection was killed in the meantime. In that case don't
only return an error, but also put back the free slot.
Fixes: b290098092 ("net/smc: cancel send and receive for terminated socket")
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rxrpc_sendmsg() returns EPIPE if there's an outstanding error, such as if
rxrpc_recvmsg() indicating ENODATA if there's nothing for it to read.
Change rxrpc_recvmsg() to return EAGAIN instead if there's nothing to read
as this particular error doesn't get stored in ->sk_err by the networking
core.
Also change rxrpc_sendmsg() so that it doesn't fail with delayed receive
errors (there's no way for it to report which call, if any, the error was
caused by).
Fixes: 17926a7932 ("[AF_RXRPC]: Provide secure RxRPC sockets for use by userspace and kernel both")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have all the infrastructure in place for calling into the
dsa_ptr->netdev_ops function pointers, install them when we configure
the DSA CPU/management interface and tear them down. The flow is
unchanged from before, but now we preserve equality of tests when
network device drivers do tests like dev->netdev_ops == &foo_ops which
was not the case before since we were allocating an entirely new
structure.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the core net_device code call into our ndo_do_ioctl() and
ndo_get_phys_port_name() functions via the wrappers defined previously
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for adding another layer of call into a DSA stacked ops
singleton, wrap the ndo_do_ioctl() call into dev_do_ioctl().
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add setsockopt SOL_IP/IP_RECVERR_4884 to return the offset to an
extension struct if present.
ICMP messages may include an extension structure after the original
datagram. RFC 4884 standardized this behavior. It stores the offset
in words to the extension header in u8 icmphdr.un.reserved[1].
The field is valid only for ICMP types destination unreachable, time
exceeded and parameter problem, if length is at least 128 bytes and
entire packet does not exceed 576 bytes.
Return the offset to the start of the extension struct when reading an
ICMP error from the error queue, if it matches the above constraints.
Do not return the raw u8 field. Return the offset from the start of
the user buffer, in bytes. The kernel does not return the network and
transport headers, so subtract those.
Also validate the headers. Return the offset regardless of validation,
as an invalid extension must still not be misinterpreted as part of
the original datagram. Note that !invalid does not imply valid. If
the extension version does not match, no validation can take place,
for instance.
For backward compatibility, make this optional, set by setsockopt
SOL_IP/IP_RECVERR_RFC4884. For API example and feature test, see
github.com/wdebruij/kerneltools/blob/master/tests/recv_icmp_v2.c
For forward compatibility, reserve only setsockopt value 1, leaving
other bits for additional icmp extensions.
Changes
v1->v2:
- convert word offset to byte offset from start of user buffer
- return in ee_data as u8 may be insufficient
- define extension struct and object header structs
- return len only if constraints met
- if returning len, also validate
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is just used once, and a direct return for the redirect to the AF
case is much easier to follow than jumping to the end of a very long
function.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer. Adapt sctp_setsockopt to use a
kzfree for this case.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch from kzfree to sctp_setsockopt_auth_key + kfree to prepare for
moving the kfree to common code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename sctp_setsockopt_bindx_kernel back to sctp_setsockopt_bindx,
and use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer in the old sctp_setsockopt_bindx.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare for for moving the copy_from_user from the individual sockopts
to the main setsockopt helper. As of this commit the kopt variable
is not used yet, but the following commits will start using it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just check for a NULL method instead of wiring up
sock_no_{get,set}sockopt.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle the few cases that need special treatment in-line using
in_compat_syscall(). This also removes all the now unused
compat_{get,set}sockopt methods.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out one helper each for setting the native and compat
version of the MCAST_MSFILTER option.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out one helper each for setting the native and compat
version of the MCAST_MSFILTER option.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out one helper each for getting the native and compat
version of the MCAST_MSFILTER option.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle the few cases that need special treatment in-line using
in_compat_syscall().
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out one helper each for setting the native and compat
version of the MCAST_MSFILTER option.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out one helper each for setting the native and compat
version of the MCAST_MSFILTER option.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out one helper each for getting the native and compat
version of the MCAST_MSFILTER option.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split nf_sockopt into a getsockopt and setsockopt side as they share
very little code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lift the in_compat_syscall() from the callers instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
All instances handle compat sockopts via in_compat_syscall() now, so
remove the compat_{get,set} methods as well as the
compat_nf_{get,set}sockopt wrappers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge the native and compat {get,set}sockopt handlers using
in_compat_syscall(). Note that this required moving a fair
amout of code around to be done sanely.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge the native and compat {get,set}sockopt handlers using
in_compat_syscall().
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge the native and compat {get,set}sockopt handlers using
in_compat_syscall().
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge the native and compat {get,set}sockopt handlers using
in_compat_syscall().
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the ->compat_{get,set}sockopt proto_ops methods are gone
there is no good reason left to keep the compat syscalls separate.
This fixes the odd use of unsigned int for the compat_setsockopt
optlen and the missing sock_use_custom_sol_socket.
It would also easily allow running the eBPF hooks for the compat
syscalls, but such a large change in behavior does not belong into
a consolidation patch like this one.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the compat handling to sock_common_{get,set}sockopt instead,
keyed of in_compat_syscall(). This allow to remove the now unused
->compat_{get,set}sockopt methods from struct proto_ops.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper that copies either a native or compat bpf_fprog from
userspace after verifying the length, and remove the compat setsockopt
handlers that now aren't required.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return early when sockfd_lookup_light fails to reduce a level of
indentation for most of the function body.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return early when sockfd_lookup_light fails to reduce a level of
indentation for most of the function body.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
All implementations of these two methods are dummies that always
return -EINVAL.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Delete the doubled word "be" in a comment.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Cc: netdev@vger.kernel.org
Cc: linux-rdma@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Delete the doubled word "the" in a comment.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
When a listen socket is closed then all non-accepted sockets in its
accept queue are to be released. Inside __smc_release() the helper
smc_restore_fallback_changes() restores the changes done to the socket
without to check if the clcsocket has a file set. This can result in
a crash. Fix this by checking the file pointer first.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: f536dffc0b ("net/smc: fix closing of fallback SMC sockets")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two buffers are allocated for each SMC connection. Each buffer is
added to a buffer list after creation. When the second buffer
allocation fails, the first buffer is freed but not deleted from
the list. This might result in crashes when another connection picks
up the freed buffer later and starts to work with it.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: 6511aad3f0 ("net/smc: change smc_buf_free function parameters")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dma related ...sync_sg... functions check the link state before the
dma function is actually called. But the check in smc_link_usable()
allows links in ACTIVATING state which are not yet mapped to dma memory.
Under high load it may happen that the sync_sg functions are called for
such a link which results in an debug output like
DMA-API: mlx5_core 0002:00:00.0: device driver tries to sync
DMA memory it has not allocated [device address=0x0000000103370000]
[size=65536 bytes]
To fix that introduce a helper to check for the link state ACTIVE and
use it where appropriate. And move the link state update to ACTIVATING
to the end of smcr_link_init() when most initial setup is done.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: d854fcbfae ("net/smc: add new link state and related helpers")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As smc client the delete link requests are assigned to the flow when
_any_ flow is active. This may break other flows that do not expect
delete link requests during their handling. Fix that by assigning the
request only when an add link flow is active. With that fix the code
for smc client and smc server is the same, so remove the separate
handling.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: 9ec6bf19ec ("net/smc: llc_del_link_work and use the LLC flow for delete link")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a new ib device is up smc will send an add link invitation to the
peer if needed. This is currently done with rudimentary flow control.
Under high workload these add link invitations can disturb other llc
flows because they arrive unexpected. Fix this by integrating the
invitations into the normal llc event flow and handle them as a flow.
While at it, check for already assigned requests in the flow before
the new add link request is assigned.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: 1f90a05d9f ("net/smc: add smcr_port_add() and smcr_link_up() processing")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be save from unexpected or late llc response messages check if the
arrived message fits to the current flow type and drop out-of-flow
messages. And drop it when there is already a response assigned to
the flow.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: ef79d439cd ("net/smc: process llc responses in tasklet context")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before an smc ib device is used the first time for an smc link it is
lazily initialized. When there are 2 active link groups and a new ib
device is brought online then it might happen that 2 link creations run
in parallel and enter smc_ib_setup_per_ibdev(). Both allocate new send
and receive completion queues on the device, but only one set of them
keeps assigned and the other leaks.
Fix that by protecting the setup and cleanup code using a mutex.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: f3c1deddb2 ("net/smc: separate function for link initialization")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For new rdma connections the SMC server assigns the link and sends the
link data in the clc accept message. To match the correct link use not
only the qp_num but also the gid and the mac of the links. If there are
equal qp_nums for different links the wrong link would be chosen.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: 0fb0b02bd6 ("net/smc: adapt SMC client code to use the LLC flow")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a link-down condition we notify the SMC server and expect that the
server will finally trigger the link clear processing on the client
side. This could fail when anything along this notification path goes
wrong. Clear the link as part of SMC client link-down processing to
prevent dangling links.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: 541afa10c1 ("net/smc: add smcr_port_err() and smcr_link_down() processing")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A delete link could arrive during confirm link processing. Handle this
situation directly in smc_llc_srv_conf_link() rather than using the
logic in smc_llc_wait() to avoid the unexpected message handling there.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: 1551c95b61 ("net/smc: final part of add link processing as SMC server")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
p9_read_work and p9_fd_cancelled may be called concurrently.
In some cases, req->req_list may be deleted by both p9_read_work
and p9_fd_cancelled.
We can fix it by ignoring replies associated with a cancelled
request and ignoring cancelled request if message has been received
before lock.
Link: http://lkml.kernel.org/r/20200612090833.36149-1-wanghai38@huawei.com
Fixes: 60ff779c4a ("9p: client: remove unused code and any reference to "cancelled" function")
Cc: <stable@vger.kernel.org> # v3.12+
Reported-by: syzbot+77a25acfa0382e06ab23@syzkaller.appspotmail.com
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: Dominique Martinet <asmadeus@codewreck.org>
p9_fd_open just fgets file descriptors passed in from userspace, but
doesn't verify that they are valid for read or writing. This gets
cought down in the VFS when actually attempting a read or write, but
a new warning added in linux-next upsets syzcaller.
Fix this by just verifying the fds early on.
Link: http://lkml.kernel.org/r/20200710085722.435850-1-hch@lst.de
Reported-by: syzbot+e6f77e16ff68b2434a2c@syzkaller.appspotmail.com
Signed-off-by: Christoph Hellwig <hch@lst.de>
[Dominique: amend goto as per Doug Nazar's review]
Signed-off-by: Dominique Martinet <asmadeus@codewreck.org>
Same as for udp4, let BPF program override the socket lookup result, by
selecting a receiving socket of its choice or failing the lookup, if no
connected UDP socket matched packet 4-tuple.
Suggested-by: Marek Majkowski <marek@cloudflare.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200717103536.397595-11-jakub@cloudflare.com
Prepare for calling into reuseport from __udp6_lib_lookup as well.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200717103536.397595-10-jakub@cloudflare.com
Following INET/TCP socket lookup changes, modify UDP socket lookup to let
BPF program select a receiving socket before searching for a socket by
destination address and port as usual.
Lookup of connected sockets that match packet 4-tuple is unaffected by this
change. BPF program runs, and potentially overrides the lookup result, only
if a 4-tuple match was not found.
Suggested-by: Marek Majkowski <marek@cloudflare.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200717103536.397595-9-jakub@cloudflare.com
Prepare for calling into reuseport from __udp4_lib_lookup as well.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200717103536.397595-8-jakub@cloudflare.com
Following ipv4 stack changes, run a BPF program attached to netns before
looking up a listening socket. Program can return a listening socket to use
as result of socket lookup, fail the lookup, or take no action.
Suggested-by: Marek Majkowski <marek@cloudflare.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200717103536.397595-7-jakub@cloudflare.com
Prepare for calling into reuseport from inet6_lookup_listener as well.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200717103536.397595-6-jakub@cloudflare.com
Run a BPF program before looking up a listening socket on the receive path.
Program selects a listening socket to yield as result of socket lookup by
calling bpf_sk_assign() helper and returning SK_PASS code. Program can
revert its decision by assigning a NULL socket with bpf_sk_assign().
Alternatively, BPF program can also fail the lookup by returning with
SK_DROP, or let the lookup continue as usual with SK_PASS on return, when
no socket has been selected with bpf_sk_assign().
This lets the user match packets with listening sockets freely at the last
possible point on the receive path, where we know that packets are destined
for local delivery after undergoing policing, filtering, and routing.
With BPF code selecting the socket, directing packets destined to an IP
range or to a port range to a single socket becomes possible.
In case multiple programs are attached, they are run in series in the order
in which they were attached. The end result is determined from return codes
of all the programs according to following rules:
1. If any program returned SK_PASS and selected a valid socket, the socket
is used as result of socket lookup.
2. If more than one program returned SK_PASS and selected a socket,
last selection takes effect.
3. If any program returned SK_DROP, and no program returned SK_PASS and
selected a socket, socket lookup fails with -ECONNREFUSED.
4. If all programs returned SK_PASS and none of them selected a socket,
socket lookup continues to htable-based lookup.
Suggested-by: Marek Majkowski <marek@cloudflare.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200717103536.397595-5-jakub@cloudflare.com
Prepare for calling into reuseport from __inet_lookup_listener as well.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200717103536.397595-4-jakub@cloudflare.com
Add a new program type BPF_PROG_TYPE_SK_LOOKUP with a dedicated attach type
BPF_SK_LOOKUP. The new program kind is to be invoked by the transport layer
when looking up a listening socket for a new connection request for
connection oriented protocols, or when looking up an unconnected socket for
a packet for connection-less protocols.
When called, SK_LOOKUP BPF program can select a socket that will receive
the packet. This serves as a mechanism to overcome the limits of what
bind() API allows to express. Two use-cases driving this work are:
(1) steer packets destined to an IP range, on fixed port to a socket
192.0.2.0/24, port 80 -> NGINX socket
(2) steer packets destined to an IP address, on any port to a socket
198.51.100.1, any port -> L7 proxy socket
In its run-time context program receives information about the packet that
triggered the socket lookup. Namely IP version, L4 protocol identifier, and
address 4-tuple. Context can be further extended to include ingress
interface identifier.
To select a socket BPF program fetches it from a map holding socket
references, like SOCKMAP or SOCKHASH, and calls bpf_sk_assign(ctx, sk, ...)
helper to record the selection. Transport layer then uses the selected
socket as a result of socket lookup.
In its basic form, SK_LOOKUP acts as a filter and hence must return either
SK_PASS or SK_DROP. If the program returns with SK_PASS, transport should
look for a socket to receive the packet, or use the one selected by the
program if available, while SK_DROP informs the transport layer that the
lookup should fail.
This patch only enables the user to attach an SK_LOOKUP program to a
network namespace. Subsequent patches hook it up to run on local delivery
path in ipv4 and ipv6 stacks.
Suggested-by: Marek Majkowski <marek@cloudflare.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200717103536.397595-3-jakub@cloudflare.com
Validate MAC address before copying the same to outgoing frame
skb destination address. Since a node can have zero mac
address for Link B until a valid frame is received over
that link, this fix address the issue of a zero MAC address
being in the packet.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For small Ethernet frames with size less than minimum size 66 for HSR
vs 60 for regular Ethernet frames, hsr driver currently doesn't pad the
frame to make it minimum size. This results in incorrect LSDU size being
populated in the HSR tag for these frames. Fix this by padding the frame
to the minimum size applicable for HSR.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When nfc_register_device fails in nci_register_device,
destroy_workqueue() shouled be called to destroy ndev->tx_wq.
Fixes: 3c1c0f5dc8 ("NFC: NCI: Fix nci_register_device init sequence")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two existing SNMP counters, TCPDSACKRecv and TCPDSACKOfoRecv,
which are incremented depending on whether the DSACKed range is below
the cumulative ACK sequence number or not. Unfortunately, these both
implicitly assume each DSACK covers only one segment. This makes these
counters unusable for estimating spurious retransmit rates,
or real/non-spurious loss rate.
This patch introduces a new SNMP counter, TCPDSACKRecvSegs, which tracks
the estimated number of duplicate segments based on:
(DSACKed sequence range) / MSS. This counter is usable for estimating
spurious retransmit rates, or real/non-spurious loss rate.
Signed-off-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, while processing DSACK, we assume DSACK covers only one
segment. This leads to significant underestimation of DSACKs with
LRO/GRO. This patch fixes segment accounting with DSACK by estimating
segment count from DSACK sequence range / MSS.
Signed-off-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yousuk Seung <ysseung@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
since commit d47a721520 ("mptcp: fix race in subflow_data_ready()"), it
is possible to observe a regression in MP_JOIN kselftests. For sockets in
TCP_CLOSE state, it's not sufficient to just wake up the main socket: we
also need to ensure that received data are made available to the reader.
Silence the WARN_ON_ONCE() in these cases: it preserves the syzkaller fix
and restores kselftests when they are ran as follows:
# while true; do
> make KBUILD_OUTPUT=/tmp/kselftest TARGETS=net/mptcp kselftest
> done
Reported-by: Florian Westphal <fw@strlen.de>
Fixes: d47a721520 ("mptcp: fix race in subflow_data_ready()")
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/47
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reorders the masks array every 4 seconds based on their
usage count. This greatly reduces the masks per packet hit, and
hence the overall performance. Especially in the OVS/OVN case for
OpenShift.
Here are some results from the OVS/OVN OpenShift test, which use
8 pods, each pod having 512 uperf connections, each connection
sends a 64-byte request and gets a 1024-byte response (TCP).
All uperf clients are on 1 worker node while all uperf servers are
on the other worker node.
Kernel without this patch : 7.71 Gbps
Kernel with this patch applied: 14.52 Gbps
We also run some tests to verify the rebalance activity does not
lower the flow insertion rate, which does not.
Signed-off-by: Eelco Chaudron <echaudro@redhat.com>
Tested-by: Andrew Theurer <atheurer@redhat.com>
Reviewed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Better to unregister the file system before destroying the kmem_cache
cache of the inodes, so that the inodes are freed before we are trying
to destroy it. Otherwise, kmem_cache yells that some objects are live.
Signed-off-by: Dan Aloni <dan@kernelim.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Naresh reported some compile errors:
arm build failed due this error on linux-next 20200713 and 20200713
net/ipv6/ip6_vti.o: In function `vti6_rcv_tunnel':
ip6_vti.c:(.text+0x1d20): undefined reference to `xfrm6_tunnel_spi_lookup'
This happened when set CONFIG_IPV6_VTI=y and CONFIG_INET6_TUNNEL=m.
We don't really want ip6_vti to depend inet6_tunnel completely, but
only to disable the tunnel code when inet6_tunnel is not seen.
So instead of adding "select INET6_TUNNEL" for IPV6_VTI, this patch
is only to change to IS_REACHABLE to avoid these compile error.
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Fixes: 08622869ed ("ip6_vti: support IP6IP6 tunnel processing with .cb_handler")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
kernel test robot reported some compile errors:
ia64-linux-ld: net/xfrm/xfrm_interface.o: in function `xfrmi4_fini':
net/xfrm/xfrm_interface.c:900: undefined reference to `xfrm4_tunnel_deregister'
ia64-linux-ld: net/xfrm/xfrm_interface.c:901: undefined reference to `xfrm4_tunnel_deregister'
ia64-linux-ld: net/xfrm/xfrm_interface.o: in function `xfrmi4_init':
net/xfrm/xfrm_interface.c:873: undefined reference to `xfrm4_tunnel_register'
ia64-linux-ld: net/xfrm/xfrm_interface.c:876: undefined reference to `xfrm4_tunnel_register'
ia64-linux-ld: net/xfrm/xfrm_interface.c:885: undefined reference to `xfrm4_tunnel_deregister'
This happened when set CONFIG_XFRM_INTERFACE=y and CONFIG_INET_TUNNEL=m.
We don't really want xfrm_interface to depend inet_tunnel completely,
but only to disable the tunnel code when inet_tunnel is not seen.
So instead of adding "select INET_TUNNEL" for XFRM_INTERFACE, this patch
is only to change to IS_REACHABLE to avoid these compile error.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: da9bbf0598 ("xfrm: interface: support IPIP and IPIP6 tunnels processing with .cb_handler")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
In case we're compiling espintcp support only for IPv6, we should
still initialize the common code.
Fixes: 26333c37fc ("xfrm: add IPv6 support for espintcp")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
man 2 recv says:
RETURN VALUE
When a stream socket peer has performed an orderly shutdown, the
return value will be 0 (the traditional "end-of-file" return).
Currently, this works for blocking reads, but non-blocking reads will
return -EAGAIN. This patch overwrites that return value when the peer
won't send us any more data.
Fixes: e27cca96cd ("xfrm: add espintcp (RFC 8229)")
Reported-by: Andrew Cagney <cagney@libreswan.org>
Tested-by: Andrew Cagney <cagney@libreswan.org>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Currently, non-blocking sends from userspace result in EOPNOTSUPP.
To support this, we need to tell espintcp_sendskb_locked() and
espintcp_sendskmsg_locked() that non-blocking operation was requested
from espintcp_sendmsg().
Fixes: e27cca96cd ("xfrm: add espintcp (RFC 8229)")
Reported-by: Andrew Cagney <cagney@libreswan.org>
Tested-by: Andrew Cagney <cagney@libreswan.org>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Mirred currently does not mix well with blocks executed after the qdisc
root lock is taken. This includes classification blocks (such as in PRIO,
ETS, DRR qdiscs) and qevents. The locking caused by the packet mirrored by
mirred can cause deadlocks: either when the thread of execution attempts to
take the lock a second time, or when two threads end up waiting on each
other's locks.
The qevent patchset attempted to not introduce further badness of this
sort, and dropped the lock before executing the qevent block. However this
lead to too little locking and races between qdisc configuration and packet
enqueue in the RED qdisc.
Before the deadlock issues are solved in a way that can be applied across
many qdiscs reasonably easily, do for qevents what is done for the
classification blocks and just keep holding the root lock.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Using uninitialized_var() is dangerous as it papers over real bugs[1]
(or can in the future), and suppresses unrelated compiler warnings
(e.g. "unused variable"). If the compiler thinks it is uninitialized,
either simply initialize the variable or make compiler changes.
In preparation for removing[2] the[3] macro[4], remove all remaining
needless uses with the following script:
git grep '\buninitialized_var\b' | cut -d: -f1 | sort -u | \
xargs perl -pi -e \
's/\buninitialized_var\(([^\)]+)\)/\1/g;
s:\s*/\* (GCC be quiet|to make compiler happy) \*/$::g;'
drivers/video/fbdev/riva/riva_hw.c was manually tweaked to avoid
pathological white-space.
No outstanding warnings were found building allmodconfig with GCC 9.3.0
for x86_64, i386, arm64, arm, powerpc, powerpc64le, s390x, mips, sparc64,
alpha, and m68k.
[1] https://lore.kernel.org/lkml/20200603174714.192027-1-glider@google.com/
[2] https://lore.kernel.org/lkml/CA+55aFw+Vbj0i=1TGqCR5vQkCzWJ0QxK6CernOU6eedsudAixw@mail.gmail.com/
[3] https://lore.kernel.org/lkml/CA+55aFwgbgqhbp1fkxvRKEpzyR5J8n1vKT1VZdz9knmPuXhOeg@mail.gmail.com/
[4] https://lore.kernel.org/lkml/CA+55aFz2500WfbKXAx8s67wrm9=yVJu65TpLgN_ybYNv0VEOKA@mail.gmail.com/
Reviewed-by: Leon Romanovsky <leonro@mellanox.com> # drivers/infiniband and mlx4/mlx5
Acked-by: Jason Gunthorpe <jgg@mellanox.com> # IB
Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless drivers
Reviewed-by: Chao Yu <yuchao0@huawei.com> # erofs
Signed-off-by: Kees Cook <keescook@chromium.org>
A busy-wait loop is used to implement waiting for bits to be copied
from the skb to the kernel buffer before retiring a block. This is
a problem on PREEMPT_RT because the copying task could be preempted
by the busy-waiting task and thus live lock in the busy-wait loop.
Replace the busy-wait logic with an rwlock_t. This provides lockdep
coverage and makes the code RT ready.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce the capability to attach an eBPF program to cpumap entries.
The idea behind this feature is to add the possibility to define on
which CPU run the eBPF program if the underlying hw does not support
RSS. Current supported verdicts are XDP_DROP and XDP_PASS.
This patch has been tested on Marvell ESPRESSObin using xdp_redirect_cpu
sample available in the kernel tree to identify possible performance
regressions. Results show there are no observable differences in
packet-per-second:
$./xdp_redirect_cpu --progname xdp_cpu_map0 --dev eth0 --cpu 1
rx: 354.8 Kpps
rx: 356.0 Kpps
rx: 356.8 Kpps
rx: 356.3 Kpps
rx: 356.6 Kpps
rx: 356.6 Kpps
rx: 356.7 Kpps
rx: 355.8 Kpps
rx: 356.8 Kpps
rx: 356.8 Kpps
Co-developed-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/bpf/5c9febdf903d810b3415732e5cd98491d7d9067a.1594734381.git.lorenzo@kernel.org
Now that there's a function that calculates the SHA-256 digest of a
buffer in one step, use it instead of sha256_init() + sha256_update() +
sha256_final().
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Cc: mptcp@lists.01.org
Cc: Mat Martineau <mathew.j.martineau@linux.intel.com>
Cc: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Remove the unnecessary label from dn_dev_ioctl() and make its error
handling simpler to read.
Signed-off-by: Suraj Upadhyay <usuraj35@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The nf_tables_rule_release() function frees "rule" so we have to use
the _safe() version of list_for_each_entry().
Fixes: d0e2c7de92 ("netfilter: nf_tables: add NFT_CHAIN_BINDING")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
sybot came up with following transaction:
add table ip syz0
add chain ip syz0 syz2 { type nat hook prerouting priority 0; policy accept; }
add table ip syz0 { flags dormant; }
delete chain ip syz0 syz2
delete table ip syz0
which yields:
hook not found, pf 2 num 0
WARNING: CPU: 0 PID: 6775 at net/netfilter/core.c:413 __nf_unregister_net_hook+0x3e6/0x4a0 net/netfilter/core.c:413
[..]
nft_unregister_basechain_hooks net/netfilter/nf_tables_api.c:206 [inline]
nft_table_disable net/netfilter/nf_tables_api.c:835 [inline]
nf_tables_table_disable net/netfilter/nf_tables_api.c:868 [inline]
nf_tables_commit+0x32d3/0x4d70 net/netfilter/nf_tables_api.c:7550
nfnetlink_rcv_batch net/netfilter/nfnetlink.c:486 [inline]
nfnetlink_rcv_skb_batch net/netfilter/nfnetlink.c:544 [inline]
nfnetlink_rcv+0x14a5/0x1e50 net/netfilter/nfnetlink.c:562
netlink_unicast_kernel net/netlink/af_netlink.c:1303 [inline]
Problem is that when I added ability to override base hook registration
to make nat basechains register with the nat core instead of netfilter
core, I forgot to update nft_table_disable() to use that instead of
the 'raw' hook register interface.
In syzbot transaction, the basechain is of 'nat' type. Its registered
with the nat core. The switch to 'dormant mode' attempts to delete from
netfilter core instead.
After updating nft_table_disable/enable to use the correct helper,
nft_(un)register_basechain_hooks can be folded into the only remaining
caller.
Because nft_trans_table_enable() won't do anything when the DORMANT flag
is set, remove the flag first, then re-add it in case re-enablement
fails, else this patch breaks sequence:
add table ip x { flags dormant; }
/* add base chains */
add table ip x
The last 'add' will remove the dormant flags, but won't have any other
effect -- base chains are not registered.
Then, next 'set dormant flag' will create another 'hook not found'
splat.
Reported-by: syzbot+2570f2c036e3da5db176@syzkaller.appspotmail.com
Fixes: 4e25ceb80b ("netfilter: nf_tables: allow chain type to override hook register")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Currently the header size calculations are using an assignment
operator instead of a += operator when accumulating the header
size leading to incorrect sizes. Fix this by using the correct
operator.
Addresses-Coverity: ("Unused value")
Fixes: 302d3deb20 ("xprtrdma: Prevent inline overflow")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Add functionality to disable and remove advertising instances,
and use that functionality in MGMT add/remove advertising calls.
Currently, advertising is globally-disabled, i.e. all instances are
disabled together, even if hardware offloading is available. This
patch adds functionality to disable and remove individual adv
instances, solving two issues:
1. On new advertisement registration, a global disable was done, and
then only the new instance was enabled. This meant only the newest
instance was actually enabled.
2. On advertisement removal, the structure was removed, but the instance
was never disabled or removed, which is incorrect with hardware offload
support.
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Reviewed-by: Shyh-In Hwang <josephsih@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-07-14
The following pull-request contains BPF updates for your *net-next* tree.
We've added 21 non-merge commits during the last 1 day(s) which contain
a total of 20 files changed, 308 insertions(+), 279 deletions(-).
The main changes are:
1) Fix selftests/bpf build, from Alexei.
2) Fix resolve_btfids build issues, from Jiri.
3) Pull usermode-driver-cleanup set, from Eric.
4) Two minor fixes to bpfilter, from Alexei and Masahiro.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new port attribute, IFLA_BRPORT_MRP_IN_OPEN, which
allows to notify the userspace when the node lost the contiuity of
MRP_InTest frames.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends the function br_mrp_fill_info to return also the
status for the interconnect ring.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends the existing MRP netlink interface with the following
attributes: IFLA_BRIDGE_MRP_IN_ROLE, IFLA_BRIDGE_MRP_IN_STATE and
IFLA_BRIDGE_MRP_START_IN_TEST. These attributes are similar with their
ring attributes but they apply to the interconnect port.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thie patch adds support for MRP Interconnect. Similar with the MRP ring,
if the HW can't generate MRP_InTest frames, then the SW will try to
generate them. And if also the SW fails to generate the frames then an
error is return to userspace.
The forwarding/termination of MRP_In frames is happening in the kernel
and is done by MRP instances.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the MRP API for interconnect switchdev. Similar with the other
br_mrp_switchdev function, these function will just eventually call the
switchdev functions: switchdev_port_obj_add/del.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function notifies the userspace when the node lost the continuity
of MRP_InTest frames.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch renames the function br_mrp_port_open to
br_mrp_ring_port_open. In this way is more clear that a ring port lost
the continuity because there will be also a br_mrp_in_port_open.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends the 'struct br_mrp' to contain information regarding
the MRP interconnect. It contains the following:
- the interconnect port 'i_port', which is NULL if the node doesn't have
a interconnect role
- the interconnect id, which is similar with the ring id, but this field
is also part of the MRP_InTest frames.
- the interconnect role, which can be MIM or MIC.
- the interconnect state, which can be open or closed.
- the interconnect delayed_work for sending MRP_InTest frames and check
for lost of continuity.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Originally, bpfilter_umh was linked with -static only when
CONFIG_BPFILTER_UMH=y.
Commit 8a2cc0505c ("bpfilter: use 'userprogs' syntax to build
bpfilter_umh") silently, accidentally dropped the CONFIG_BPFILTER_UMH=y
test in the Makefile. Revive it in order to link it dynamically when
CONFIG_BPFILTER_UMH=m.
Since commit b1183b6dca ("bpfilter: check if $(CC) can link static
libc in Kconfig"), the compiler must be capable of static linking to
enable CONFIG_BPFILTER_UMH, but it requires more than needed.
To loosen the compiler requirement, I changed the dependency as follows:
depends on CC_CAN_LINK
depends on m || CC_CAN_LINK_STATIC
If CONFIG_CC_CAN_LINK_STATIC in unset, CONFIG_BPFILTER_UMH is restricted
to 'm' or 'n'.
In theory, CONFIG_CC_CAN_LINK is not required for CONFIG_BPFILTER_UMH=y,
but I did not come up with a good way to describe it.
Fixes: 8a2cc0505c ("bpfilter: use 'userprogs' syntax to build bpfilter_umh")
Reported-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Michal Kubecek <mkubecek@suse.cz>
Link: https://lore.kernel.org/bpf/20200701092644.762234-1-masahiroy@kernel.org
Make sure 'pos' is initialized to zero before calling kernel_write().
Fixes: d2ba09c17a ("net: add skeleton of bpfilter kernel module")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
As we did in the last 2 patches for vti(6), this patch is to define a
new xfrm_tunnel object 'xfrmi_ipip6_handler' to register for AF_INET6,
and a new xfrm6_tunnel object 'xfrmi_ip6ip_handler' to register for
AF_INET.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
An xfrm6_tunnel object is linked into the list when registering,
so vti_ipv6_handler can not be registered twice, otherwise its
next pointer will be overwritten on the second time.
So this patch is to define a new xfrm6_tunnel object to register
for AF_INET.
Fixes: 2ab110cbb0 ("ip6_vti: support IP6IP tunnel processing")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
An xfrm_tunnel object is linked into the list when registering,
so vti_ipip_handler can not be registered twice, otherwise its
next pointer will be overwritten on the second time.
So this patch is to define a new xfrm_tunnel object to register
for AF_INET6.
Fixes: e6ce64570f ("ip_vti: support IPIP6 tunnel processing")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-07-13
The following pull-request contains BPF updates for your *net-next* tree.
We've added 36 non-merge commits during the last 7 day(s) which contain
a total of 62 files changed, 2242 insertions(+), 468 deletions(-).
The main changes are:
1) Avoid trace_printk warning banner by switching bpf_trace_printk to use
its own tracing event, from Alan.
2) Better libbpf support on older kernels, from Andrii.
3) Additional AF_XDP stats, from Ciara.
4) build time resolution of BTF IDs, from Jiri.
5) BPF_CGROUP_INET_SOCK_RELEASE hook, from Stanislav.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch we try to kill 2 birds with 1 stone.
First of all, some switches that use tag_ocelot.c don't have the exact
same bitfield layout for the DSA tags. The destination ports field is
different for Seville VSC9953 for example. So the choices are to either
duplicate tag_ocelot.c into a new tag_seville.c (sub-optimal) or somehow
take into account a supposed ocelot->dest_ports_offset when packing this
field into the DSA injection header (again not ideal).
Secondly, tag_ocelot.c already needs to memset a 128-bit area to zero
and call some packing() functions of dubious performance in the
fastpath. And most of the values it needs to pack are pretty much
constant (BYPASS=1, SRC_PORT=CPU, DEST=port index). So it would be good
if we could improve that.
The proposed solution is to allocate a memory area per port at probe
time, initialize that with the statically defined bits as per chip
hardware revision, and just perform a simpler memcpy in the fastpath.
Other alternatives have been analyzed, such as:
- Create a separate tag_seville.c: too much code duplication for just 1
bit field difference.
- Create a separate DSA_TAG_PROTO_SEVILLE under tag_ocelot.c, just like
tag_brcm.c, which would have a separate .xmit function. Again, too
much code duplication for just 1 bit field difference.
- Allocate the template from the init function of the tag_ocelot.c
module, instead of from the driver: couldn't figure out a method of
accessing the correct port template corresponding to the correct
tagger in the .xmit function.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
KASAN report null-ptr-deref error when register_netdev() failed:
KASAN: null-ptr-deref in range [0x00000000000003c0-0x00000000000003c7]
CPU: 2 PID: 422 Comm: ip Not tainted 5.8.0-rc4+ #12
Call Trace:
ip6gre_init_net+0x4ab/0x580
? ip6gre_tunnel_uninit+0x3f0/0x3f0
ops_init+0xa8/0x3c0
setup_net+0x2de/0x7e0
? rcu_read_lock_bh_held+0xb0/0xb0
? ops_init+0x3c0/0x3c0
? kasan_unpoison_shadow+0x33/0x40
? __kasan_kmalloc.constprop.0+0xc2/0xd0
copy_net_ns+0x27d/0x530
create_new_namespaces+0x382/0xa30
unshare_nsproxy_namespaces+0xa1/0x1d0
ksys_unshare+0x39c/0x780
? walk_process_tree+0x2a0/0x2a0
? trace_hardirqs_on+0x4a/0x1b0
? _raw_spin_unlock_irq+0x1f/0x30
? syscall_trace_enter+0x1a7/0x330
? do_syscall_64+0x1c/0xa0
__x64_sys_unshare+0x2d/0x40
do_syscall_64+0x56/0xa0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
ip6gre_tunnel_uninit() has set 'ign->fb_tunnel_dev' to NULL, later
access to ign->fb_tunnel_dev cause null-ptr-deref. Fix it by saving
'ign->fb_tunnel_dev' to local variable ndev.
Fixes: dafabb6590 ("ip6_gre: fix use-after-free in ip6gre_tunnel_lookup()")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sparse tool complains as follows:
net/core/dev.c:5594:1: warning:
symbol '__pcpu_scope_flush_works' was not declared. Should it be static?
'flush_works' is not used outside of dev.c, so marks
it static.
Fixes: 41852497a9 ("net: batch calls to flush_all_backlogs()")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, shared blocks were only relevant for the pseudo-qdiscs ingress
and clsact. Recently, a qevent facility was introduced, which allows to
bind blocks to well-defined slots of a qdisc instance. RED in particular
got two qevents: early_drop and mark. Drivers that wish to offload these
blocks will be sent the usual notification, and need to know which qdisc it
is related to.
To that end, extend flow_block_offload with a "sch" pointer, and initialize
as appropriate. This prompts changes in the indirect block facility, which
now tracks the scheduler in addition to the netdevice. Update signatures of
several functions similarly.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple fixes which require no deep knowledge of the code.
Cc: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple fixes which require no deep knowledge of the code.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple fixes which require no deep knowledge of the code.
Cc: Jon Maloy <jmaloy@redhat.com>
Cc: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple fixes which require no deep knowledge of the code.
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the warning "Function parameter or member 'inode' not described in
'__sock_release'' due to the kerneldoc being placed before
__sock_release() not sock_release(), which does not take an inode
parameter.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple fixes which require no deep knowledge of the code.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple fixes which require no deep knowledge of the code.
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple fixes which require no deep knowledge of the code.
Cc: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple fixes which require no deep knowledge of the code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple fixes which require no deep knowledge of the code.
Cc: Paul Moore <paul@paul-moore.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple fixes which require no deep knowledge of the code.
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Jozsef Kadlecsik <kadlec@netfilter.org>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple fixes which require no deep knowledge of the code.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple fixes which require no deep knowledge of the code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple fixes which require no deep knowledge of the code.
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple fixes which require no deep knowledge of the code.
Cc: Paul Moore <paul@paul-moore.com>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple fixes which require no deep knowledge of the code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple fixes which require no deep knowledge of the code.
Cc: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple fixes which require no deep knowledge of the code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple fixes which require no deep knowledge of the code.
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple fixes which require no deep knowledge of the code.
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Latchesar Ionkov <lucho@ionkov.net>
Cc: Dominique Martinet <asmadeus@codewreck.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
It can be useful for the user to know the reason behind a dropped packet.
Introduce new counters which track drops on the receive path caused by:
1. rx ring being full
2. fill ring being empty
Also, on the tx path introduce a counter which tracks the number of times
we attempt pull from the tx ring when it is empty.
Signed-off-by: Ciara Loftus <ciara.loftus@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200708072835.4427-2-ciara.loftus@intel.com
First, refactor: Dereference the svc_rdma_send_ctxt inside
svc_rdma_send() instead of at every call site.
Then, it can be passed into trace_svcrdma_post_send() to get the
proper completion ID.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Set up a completion ID in each svc_rdma_send_ctxt. The ID is used
to match an incoming Send completion to a transport and to a
previous ib_post_send().
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
When recording a trace event in the Receive path, tie decoding
results and errors to an incoming Receive completion.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Set up a completion ID in each svc_rdma_recv_ctxt. The ID is used
to match an incoming Receive completion to a transport and to a
previous ib_post_recv().
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Use these helpers in a few spots to demonstrate their use.
The remaining open-coded discriminator checks in rpcrdma will be
addressed in subsequent patches.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
- Use the _err naming convention instead
- Remove display of kernel memory address of the controlling xprt
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Final refactor: Replace internals of svc_rdma_send_error() with a
simple call to svc_rdma_send_error_msg().
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Like svc_rdma_send_error(), have svc_rdma_send_error_msg() handle
any error conditions internally, rather than duplicating that
recovery logic at every call site.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
The common "send RDMA_ERR" function should be in svc_rdma_sendto.c,
since that is where the other Send-related functions are located.
So from here, I will beef up svc_rdma_send_error_msg() and deprecate
svc_rdma_send_error().
A generic svc_rdma_send_error_msg() will need to handle both
ERR_CHUNK and ERR_VERS. Copy that logic from svc_rdma_send_error()
to svc_rdma_send_error_msg().
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Another step towards making svc_rdma_send_error_msg() and
svc_rdma_send_error() similar enough to eliminate one of them.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Commit 4757d90b15 ("svcrdma: Report Write/Reply chunk overruns")
made an effort to preserve I/O pages until RDMA Write completion.
In a subsequent patch, I intend to de-duplicate the two functions
that send ERR_CHUNK responses. Pull the save_io_pages() call out of
svc_rdma_send_error_msg() to make it more like
svc_rdma_send_error().
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Commit 07d0ff3b0c ("svcrdma: Clean up Read chunk path") moved the
page saver logic so that it gets executed event when an error occurs.
In that case, the I/O is never posted, and those pages are then
leaked. Errors in this path, however, are quite rare.
Fixes: 07d0ff3b0c ("svcrdma: Clean up Read chunk path")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Add similar tracepoints to those that were recently added on the
client side to track failures in the integ and priv unwrap paths.
And, let's collect the seqno-specific tracepoints together with a
common naming convention.
Regarding the gss_check_seq_num() changes: everywhere else treats
the GSS sequence number as an unsigned 32-bit integer. As far back
as 2.6.12, I couldn't find a compelling reason to do things
differently here. As a defensive change it's better to eliminate
needless implicit sign conversions.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If bridge vlan filtering is not defined we won't have
br_vlan_can_enter_range and thus will get a compile error as was
reported by Stephen and the build bot. So let's define a stub for when
vlan filtering is not used.
Fixes: 9433944368 ("net: bridge: notify on vlan tunnel changes done via the old api")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For both pidfd and seccomp, the __user pointer is not used. Update
__receive_fd() to make writing to ufd optional via a NULL check. However,
for the receive_fd_user() wrapper, ufd is NULL checked so an -EFAULT
can be returned to avoid changing the SCM_RIGHTS interface behavior. Add
new wrapper receive_fd() for pidfd and seccomp that does not use the ufd
argument. For the new helper, the allocated fd needs to be returned on
success. Update the existing callers to handle it.
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: linux-fsdevel@vger.kernel.org
Reviewed-by: Sargun Dhillon <sargun@sargun.me>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
In preparation for users of the "install a received file" logic outside
of net/ (pidfd and seccomp), relocate and rename __scm_install_fd() from
net/core/scm.c to __receive_fd() in fs/file.c, and provide a wrapper
named receive_fd_user(), as future patches will change the interface
to __receive_fd().
Additionally add a comment to fd_install() as a counterpoint to how
__receive_fd() interacts with fput().
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Dmitry Kadashev <dkadashev@gmail.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Sargun Dhillon <sargun@sargun.me>
Cc: Ido Schimmel <idosch@idosch.org>
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Cc: linux-fsdevel@vger.kernel.org
Cc: netdev@vger.kernel.org
Reviewed-by: Sargun Dhillon <sargun@sargun.me>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Duplicate the cleanups from commit 2618d530dd ("net/scm: cleanup
scm_detach_fds") into the compat code.
Replace open-coded __receive_sock() with a call to the helper.
Move the check added in commit 1f466e1f15 ("net: cleanly handle kernel
vs user buffers for ->msg_control") to before the compat call, even
though it should be impossible for an in-kernel call to also be compat.
Correct the int "flags" argument to unsigned int to match fd_install()
and similar APIs.
Regularize any remaining differences, including a whitespace issue,
a checkpatch warning, and add the check from commit 6900317f5e ("net,
scm: fix PaX detected msg_controllen overflow in scm_detach_fds") which
fixed an overflow unique to 64-bit. To avoid confusion when comparing
the compat handler to the native handler, just include the same check
in the compat handler.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sargun Dhillon <sargun@sargun.me>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Add missed sock updates to compat path via a new helper, which will be
used more in coming patches. (The net/core/scm.c code is left as-is here
to assist with -stable backports for the compat path.)
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sargun Dhillon <sargun@sargun.me>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: stable@vger.kernel.org
Fixes: 48a87cc26c ("net: netprio: fd passed in SCM_RIGHTS datagram not set correctly")
Fixes: d84295067f ("net: net_cls: fd passed in SCM_RIGHTS datagram not set correctly")
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Using BTF_ID_LIST macro to define lists for several helpers
using BTF arguments.
And running resolve_btfids on vmlinux elf object during linking,
so the .BTF_ids section gets the IDs resolved.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200711215329.41165-5-jolsa@kernel.org
Check `num_rsp` before using it as for-loop counter. Add `unlock` label.
Cc: stable@vger.kernel.org
Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Check `num_rsp` before using it as for-loop counter.
Cc: stable@vger.kernel.org
Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Ensure that the connect worker is awoken if an attempt to establish
a connection is unsuccessful. Otherwise the worker waits forever
and the transport workload hangs.
Connect errors should not attempt to destroy the ep, since the
connect worker continues to use it after the handler runs, so these
errors are now handled independently of DISCONNECTED events.
Reported-by: Dan Aloni <dan@kernelim.com>
Fixes: e28ce90083 ("xprtrdma: kmalloc rpcrdma_ep separate from rpcrdma_xprt")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
I noticed that when rpcrdma_xprt_connect() returns -ENOMEM,
instead of retrying the connect, the RPC client kills the
RPC task that requested the connection. We want a retry
here.
Fixes: cb586decbb ("xprtrdma: Make sendctx queue lifetime the same as connection lifetime")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Both Dan and I have observed two processes invoking
rpcrdma_xprt_disconnect() concurrently. In my case:
1. The connect worker invokes rpcrdma_xprt_disconnect(), which
drains the QP and waits for the final completion
2. This causes the newly posted Receive to flush and invoke
xprt_force_disconnect()
3. xprt_force_disconnect() sets CLOSE_WAIT and wakes up the RPC task
that is holding the transport lock
4. The RPC task invokes xprt_connect(), which calls ->ops->close
5. xprt_rdma_close() invokes rpcrdma_xprt_disconnect(), which tries
to destroy the QP.
Deadlock.
To prevent xprt_force_disconnect() from waking anything, handle the
clean up after a failed connection attempt in the xprt's sndtask.
The retry loop is removed from rpcrdma_xprt_connect() to ensure
that the newly allocated ep and id are properly released before
a REJECTED connection attempt can be retried.
Reported-by: Dan Aloni <dan@kernelim.com>
Fixes: e28ce90083 ("xprtrdma: kmalloc rpcrdma_ep separate from rpcrdma_xprt")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
In the error paths, there's no need to call kfree(ep) after calling
rpcrdma_ep_put(ep).
Fixes: e28ce90083 ("xprtrdma: kmalloc rpcrdma_ep separate from rpcrdma_xprt")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
xfrmi_lookup() is called on every packet. Using a single list for
looking up if_id becomes a bottleneck when having many xfrm interfaces.
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
The xfrmi context exists in the netdevice priv context.
Avoid looking for it in a separate list.
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
If someone uses the old vlan API to configure tunnel mappings we'll only
generate the old-style full port notification. That would be a problem
if we are monitoring the new vlan notifications for changes. The patch
resolves the issue by adding vlan notifications to the old tunnel netlink
code. As usual we try to compress the notifications for as many vlans
in a range as possible, thus a vlan tunnel change is considered able
to enter the "current" vlan notification range if:
1. vlan exists
2. it has actually changed (curr_change == true)
3. it passes all standard vlan notification range checks done by
br_vlan_can_enter_range() such as option equality, id continuity etc
Note that vlan tunnel changes (add/del) are considered a part of vlan
options so only RTM_NEWVLAN notification is generated with the relevant
information inside.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Restore previous behavior of CAP_SYS_ADMIN wrt loading networking
BPF programs, from Maciej Żenczykowski.
2) Fix dropped broadcasts in mac80211 code, from Seevalamuthu
Mariappan.
3) Slay memory leak in nl80211 bss color attribute parsing code, from
Luca Coelho.
4) Get route from skb properly in ip_route_use_hint(), from Miaohe Lin.
5) Don't allow anything other than ARPHRD_ETHER in llc code, from Eric
Dumazet.
6) xsk code dips too deeply into DMA mapping implementation internals.
Add dma_need_sync and use it. From Christoph Hellwig
7) Enforce power-of-2 for BPF ringbuf sizes. From Andrii Nakryiko.
8) Check for disallowed attributes when loading flow dissector BPF
programs. From Lorenz Bauer.
9) Correct packet injection to L3 tunnel devices via AF_PACKET, from
Jason A. Donenfeld.
10) Don't advertise checksum offload on ipa devices that don't support
it. From Alex Elder.
11) Resolve several issues in TCP MD5 signature support. Missing memory
barriers, bogus options emitted when using syncookies, and failure
to allow md5 key changes in established states. All from Eric
Dumazet.
12) Fix interface leak in hsr code, from Taehee Yoo.
13) VF reset fixes in hns3 driver, from Huazhong Tan.
14) Make loopback work again with ipv6 anycast, from David Ahern.
15) Fix TX starvation under high load in fec driver, from Tobias
Waldekranz.
16) MLD2 payload lengths not checked properly in bridge multicast code,
from Linus Lüssing.
17) Packet scheduler code that wants to find the inner protocol
currently only works for one level of VLAN encapsulation. Allow
Q-in-Q situations to work properly here, from Toke
Høiland-Jørgensen.
18) Fix route leak in l2tp, from Xin Long.
19) Resolve conflict between the sk->sk_user_data usage of bpf reuseport
support and various protocols. From Martin KaFai Lau.
20) Fix socket cgroup v2 reference counting in some situations, from
Cong Wang.
21) Cure memory leak in mlx5 connection tracking offload support, from
Eli Britstein.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (146 commits)
mlxsw: pci: Fix use-after-free in case of failed devlink reload
mlxsw: spectrum_router: Remove inappropriate usage of WARN_ON()
net: macb: fix call to pm_runtime in the suspend/resume functions
net: macb: fix macb_suspend() by removing call to netif_carrier_off()
net: macb: fix macb_get/set_wol() when moving to phylink
net: macb: mark device wake capable when "magic-packet" property present
net: macb: fix wakeup test in runtime suspend/resume routines
bnxt_en: fix NULL dereference in case SR-IOV configuration fails
libbpf: Fix libbpf hashmap on (I)LP32 architectures
net/mlx5e: CT: Fix memory leak in cleanup
net/mlx5e: Fix port buffers cell size value
net/mlx5e: Fix 50G per lane indication
net/mlx5e: Fix CPU mapping after function reload to avoid aRFS RX crash
net/mlx5e: Fix VXLAN configuration restore after function reload
net/mlx5e: Fix usage of rcu-protected pointer
net/mxl5e: Verify that rpriv is not NULL
net/mlx5: E-Switch, Fix vlan or qos setting in legacy mode
net/mlx5: Fix eeprom support for SFP module
cgroup: Fix sock_cgroup_data on big-endian.
selftests: bpf: Fix detach from sockmap tests
...
Commit 0c3d79bce4 ("tcp: reduce SYN-ACK
retrans for TCP_DEFER_ACCEPT") introduces syn_ack_recalc() which decides
if a minisock is held and a SYN+ACK is retransmitted or not.
If rskq_defer_accept is not zero in syn_ack_recalc(), max_retries always
has the same value because max_retries is overwritten by rskq_defer_accept
in reqsk_timer_handler().
This commit adds three changes:
- remove redundant non-zero check for rskq_defer_accept in
reqsk_timer_handler().
- remove max_retries from the arguments of syn_ack_recalc() and use
rskq_defer_accept instead.
- rename thresh to max_syn_ack_retries for readability.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Reviewed-by: Benjamin Herrenschmidt <benh@amazon.com>
CC: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to use new devlink port health reporters infrastructure, add
corresponding constructor and destructor functions.
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devlink-health reporter support on per-port basis.
The main difference existing devlink-health is that port reporters are
stored in per-devlink_port lists. Upon creation of such health reporter the
reference to a port it belongs to is stored in reporter struct.
Fill the port index attribute in devlink-health response to
allow devlink userspace utility to distinguish between device and port
reporters.
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a generic __devlink_health_reporter_find_by_name() that can be used
with arbitrary devlink health reporter list.
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devlink keeps its own reference to every reporter in a list and inits
refcount to 1 upon reporter's creation. Existing destructor waits to
free the memory indefinitely using msleep() until all references except
devlink's own are put.
Rework this mechanism by moving memory free routine to a separate
function, which is called when the last reporter reference is put.
Besides, it allows to call __devlink_health_reporter_destroy() while
locked on a reporters list mutex in symmetry to
__devlink_health_reporter_create(), which is required in follow-up
patch.
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare a common routine in devlink_health_reporter_create() for usage
in similar functions for devlink port health reporters.
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an interface to report offloaded UDP ports via ethtool netlink.
Now that core takes care of tracking which UDP tunnel ports the NICs
are aware of we can quite easily export this information out to
user space.
The responsibility of writing the netlink dumps is split between
ethtool code and udp_tunnel_nic.c - since udp_tunnel module may
not always be loaded, yet we should always report the capabilities
of the NIC.
$ ethtool --show-tunnels eth0
Tunnel information for eth0:
UDP port table 0:
Size: 4
Types: vxlan
No entries
UDP port table 1:
Size: 4
Types: geneve, vxlan-gpe
Entries (1):
port 1230, vxlan-gpe
v4:
- back to v2, build fix is now directly in udp_tunnel.h
v3:
- don't compile ETHTOOL_MSG_TUNNEL_INFO_GET in if CONFIG_INET
not set.
v2:
- fix string set count,
- reorder enums in the uAPI,
- fix type of ETHTOOL_A_TUNNEL_UDP_TABLE_TYPES to bitset
in docs and comments.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cater to devices which:
(a) may want to sleep in the callbacks;
(b) only have IPv4 support;
(c) need all the programming to happen while the netdev is up.
Drivers attach UDP tunnel offload info struct to their netdevs,
where they declare how many UDP ports of various tunnel types
they support. Core takes care of tracking which ports to offload.
Use a fixed-size array since this matches what almost all drivers
do, and avoids a complexity and uncertainty around memory allocations
in an atomic context.
Make sure that tunnel drivers don't try to replay the ports when
new NIC netdev is registered. Automatic replays would mess up
reference counting, and will be removed completely once all drivers
are converted.
v4:
- use a #define NULL to avoid build issues with CONFIG_INET=n.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Reshuffle the (__)kernel_read and (__)kernel_write helpers, and ensure
all users of in-kernel file I/O use them if they don't use iov_iter
based methods already.
-----BEGIN PGP SIGNATURE-----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=eYsI
-----END PGP SIGNATURE-----
Merge tag 'cleanup-kernel_read_write' of git://git.infradead.org/users/hch/misc
Pull in-kernel read and write op cleanups from Christoph Hellwig:
"Cleanup in-kernel read and write operations
Reshuffle the (__)kernel_read and (__)kernel_write helpers, and ensure
all users of in-kernel file I/O use them if they don't use iov_iter
based methods already.
The new WARN_ONs in combination with syzcaller already found a missing
input validation in 9p. The fix should be on your way through the
maintainer ASAP".
[ This is prep-work for the real changes coming 5.9 ]
* tag 'cleanup-kernel_read_write' of git://git.infradead.org/users/hch/misc:
fs: remove __vfs_read
fs: implement kernel_read using __kernel_read
integrity/ima: switch to using __kernel_read
fs: add a __kernel_read helper
fs: remove __vfs_write
fs: implement kernel_write using __kernel_write
fs: check FMODE_WRITE in __kernel_write
fs: unexport __kernel_write
bpfilter: switch to kernel_write
autofs: switch to kernel_write
cachefiles: switch to kernel_write
Currently, all the input checks are done in driver.
After adding the split capability to devlink port, move the checks to
devlink.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new attribute that indicates the split ability of devlink port.
Drivers are expected to set it via devlink_port_attrs_set(), before
registering the port.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new devlink port attribute that indicates the port's number of lanes.
Drivers are expected to set it via devlink_port_attrs_set(), before
registering the port.
The attribute is not passed to user space in case the number of lanes is
invalid (0).
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, devlink_port_attrs_set accepts a long list of parameters,
that most of them are devlink port's attributes.
Use the devlink_port_attrs struct to replace the relevant parameters.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The struct devlink_port_attrs holds the attributes of devlink_port.
Similarly to the previous patch, 'switch_port' attribute is another
exception.
Move 'switch_port' to be devlink_port's field.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The struct devlink_port_attrs holds the attributes of devlink_port.
The 'set' field is not devlink_port's attribute as opposed to most of the
others.
Move 'set' to be devlink_port's field called 'attrs_set'.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several users of kallsyms_show_value() were performing checks not
during "open". Refactor everything needed to gain proper checks against
file->f_cred for modules, kprobes, and bpf.
-----BEGIN PGP SIGNATURE-----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=ib5Q
-----END PGP SIGNATURE-----
Merge tag 'kallsyms_show_value-v5.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull kallsyms fix from Kees Cook:
"Refactor kallsyms_show_value() users for correct cred.
I'm not delighted by the timing of getting these changes to you, but
it does fix a handful of kernel address exposures, and no one has
screamed yet at the patches.
Several users of kallsyms_show_value() were performing checks not
during "open". Refactor everything needed to gain proper checks
against file->f_cred for modules, kprobes, and bpf"
* tag 'kallsyms_show_value-v5.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
selftests: kmod: Add module address visibility test
bpf: Check correct cred for CAP_SYSLOG in bpf_dump_raw_ok()
kprobes: Do not expose probe addresses to non-CAP_SYSLOG
module: Do not expose section addresses to non-CAP_SYSLOG
module: Refactor section attr into bin attribute
kallsyms: Refactor kallsyms_show_value() to take cred
exposes basic inet socket attribute, plus some MPTCP socket
fields comprising PM status and MPTCP-level sequence numbers.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mptcp_token_iter_next() allow traversing all the MPTCP
sockets inside the token container belonging to the given
network namespace with a quite standard iterator semantic.
That will be used by the next patch, but keep the API generic,
as we plan to use this later for PM's sake.
Additionally export mptcp_token_get_sock(), as it also
will be used by the diag module.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit bf9765145b ("sock: Make sk_protocol a 16-bit value")
the current size of 'sdiag_protocol' is not sufficient to represent
the possible protocol values.
This change introduces a new inet diag request attribute to let
user space specify the relevant protocol number using u32 values.
The attribute is parsed by inet diag core on get/dump command
and the extended protocol value, if available, is preferred to
'sdiag_protocol' to lookup the diag handler.
The parse attributed are exposed to all the diag handlers via
the cb->data.
Note that inet_diag_dump_one_icsk() is left unmodified, as it
will not be used by protocol using the extended attribute.
Suggested-by: David S. Miller <davem@davemloft.net>
Co-developed-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: Christoph Paasch <cpaasch@apple.com>
Acked-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the genlmsg_put() call in ethnl_default_dumpit() fails, we bail out
without checking if we already have some messages in current skb like we do
with ethnl_default_dump_one() failure later. Therefore if existing messages
almost fill up the buffer so that there is not enough space even for
netlink and genetlink header, we lose all prepared messages and return and
error.
Rather than duplicating the skb->len check, move the genlmsg_put(),
genlmsg_cancel() and genlmsg_end() calls into ethnl_default_dump_one().
This is also more logical as all message composition will be in
ethnl_default_dump_one() and only iteration logic will be left in
ethnl_default_dumpit().
Fixes: 728480f124 ("ethtool: default handlers for GET requests")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When tcf_block_get() fails inside atm_tc_init(),
atm_tc_put() is called to release the qdisc p->link.q.
But the flow->ref prevents it to do so, as the flow->ref
is still zero.
Fix this by moving the p->link.ref initialization before
tcf_block_get().
Fixes: 6529eaba33 ("net: sched: introduce tcf block infractructure")
Reported-and-tested-by: syzbot+d411cff6ab29cc2c311b@syzkaller.appspotmail.com
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to ip_vti, IPIP and IPIP6 tunnels processing can easily
be done with .cb_handler for xfrm interface.
v1->v2:
- no change.
v2-v3:
- enable it only when CONFIG_INET_XFRM_TUNNEL is defined, to fix the
build error, reported by kbuild test robot.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Similar to ip6_vti, IP6IP6 and IP6IP tunnels processing can easily
be done with .cb_handler for xfrm interface.
v1->v2:
- no change.
v2-v3:
- enable it only when CONFIG_INET6_XFRM_TUNNEL is defined, to fix
the build error, reported by kbuild test robot.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
The child tunnel if_id will be used for xfrm interface's lookup
when processing the IP(6)IP(6) packets in the next patches.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
For IP6IP tunnel processing, the functions called will be the
same as that for IP6IP6 tunnel's. So reuse it and register it
with family == AF_INET.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Similar to IPIP tunnel's processing, this patch is to support
IP6IP6 tunnel processing with .cb_handler.
v1->v2:
- no change.
v2-v3:
- enable it only when CONFIG_INET6_XFRM_TUNNEL is defined, to fix
the build error, reported by kbuild test robot.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
For IPIP6 tunnel processing, the functions called will be the
same as that for IPIP tunnel's. So reuse it and register it
with family == AF_INET6.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
With tunnel4_input_afinfo added, IPIP tunnel processing in
ip_vti can be easily done with .cb_handler. So replace the
processing by calling ip_tunnel_rcv() with it.
v1->v2:
- no change.
v2-v3:
- enable it only when CONFIG_INET_XFRM_TUNNEL is defined, to fix
the build error, reported by kbuild test robot.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This patch is to register a callback function tunnel6_rcv_cb with
is_ipip set in a xfrm_input_afinfo object for tunnel6 and tunnel46.
It will be called by xfrm_rcv_cb() from xfrm_input() when family
is AF_INET6 and proto is IPPROTO_IPIP or IPPROTO_IPV6.
v1->v2:
- Fix a sparse warning caused by the missing "__rcu", as Jakub
noticed.
- Handle the err returned by xfrm_input_register_afinfo() in
tunnel6_init/fini(), as Sabrina noticed.
v2->v3:
- Add "#if IS_ENABLED(CONFIG_INET6_XFRM_TUNNEL)" to fix the build error
when xfrm is disabled, reported by kbuild test robot
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This patch is to register a callback function tunnel4_rcv_cb with
is_ipip set in a xfrm_input_afinfo object for tunnel4 and tunnel64.
It will be called by xfrm_rcv_cb() from xfrm_input() when family
is AF_INET and proto is IPPROTO_IPIP or IPPROTO_IPV6.
v1->v2:
- Fix a sparse warning caused by the missing "__rcu", as Jakub
noticed.
- Handle the err returned by xfrm_input_register_afinfo() in
tunnel4_init/fini(), as Sabrina noticed.
v2->v3:
- Add "#if IS_ENABLED(CONFIG_INET_XFRM_TUNNEL)" to fix the build error
when xfrm is disabled, reported by kbuild test robot.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This patch is to add a new member is_ipip to struct xfrm_input_afinfo,
to allow another group family of callback functions to be registered
with is_ipip set.
This will be used for doing a callback for struct xfrm(6)_tunnel of
ipip/ipv6 tunnels in xfrm_input() by calling xfrm_rcv_cb(), which is
needed by ipip/ipv6 tunnels' support in ip(6)_vti and xfrm interface
in the next patches.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
When evaluating access control over kallsyms visibility, credentials at
open() time need to be used, not the "current" creds (though in BPF's
case, this has likely always been the same). Plumb access to associated
file->f_cred down through bpf_dump_raw_ok() and its callers now that
kallsysm_show_value() has been refactored to take struct cred.
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: bpf@vger.kernel.org
Cc: stable@vger.kernel.org
Fixes: 7105e828c0 ("bpf: allow for correlation of maps and helpers in dump")
Signed-off-by: Kees Cook <keescook@chromium.org>
A scenario has been observed where a 'bc_init' message for a link is not
retransmitted if it fails to be received by the peer. This leads to the
peer never establishing the link fully and it discarding all other data
received on the link. In this scenario the message is lost in transit to
the peer.
The issue is traced to the 'nxt_retr' field of the skb not being
initialised for links that aren't a bc_sndlink. This leads to the
comparison in tipc_link_advance_transmq() that gates whether to attempt
retransmission of a message performing in an undesirable way.
Depending on the relative value of 'jiffies', this comparison:
time_before(jiffies, TIPC_SKB_CB(skb)->nxt_retr)
may return true or false given that 'nxt_retr' remains at the
uninitialised value of 0 for non bc_sndlinks.
This is most noticeable shortly after boot when jiffies is initialised
to a high value (to flush out rollover bugs) and we compare a jiffies of,
say, 4294940189 to zero. In that case time_before returns 'true' leading
to the skb not being retransmitted.
The fix is to ensure that all skbs have a valid 'nxt_retr' time set for
them and this is achieved by refactoring the setting of this value into
a central function.
With this fix, transmission losses of 'bc_init' messages do not stall
the link establishment forever because the 'bc_init' message is
retransmitted and the link eventually establishes correctly.
Fixes: 382f598fb6 ("tipc: reduce duplicate packets for unicast traffic")
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements the known parts of the Realtek 4 byte
tag protocol version 0xA, as found in the RTL8366RB
DSA switch.
It is designated as protocol version 0xA as a
different Realtek 4 byte tag format with protocol
version 0x9 is known to exist in the Realtek RTL8306
chips.
The tag and switch chip lacks public documentation, so
the tag format has been reverse-engineered from
packet dumps. As only ingress traffic has been available
for analysis an egress tag has not been possible to
develop (even using educated guesses about bit fields)
so this is as far as it gets. It is not known if the
switch even supports egress tagging.
Excessive attempts to figure out the egress tag format
was made. When nothing else worked, I just tried all bit
combinations with 0xannp where a is protocol and p is
port. I looped through all values several times trying
to get a response from ping, without any positive
result.
Using just these ingress tags however, the switch
functionality is vastly improved and the packets find
their way into the destination port without any
tricky VLAN configuration. On the D-Link DIR-685 the
LAN ports now come up and respond to ping without
any command line configuration so this is a real
improvement for users.
Egress packets need to be restricted to the proper
target ports using VLAN, which the RTL8366RB DSA
switch driver already sets up.
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define 100G, 200G and 400G link modes using 100Gbps per lane
LR, ER and FR are defined as a single link mode because they are
using same technology and by design are fully interoperable.
EEPROM content indicates if the module is LR, ER, or FR, and the
user space ethtool decoder is planned to support decoding these
modes in the EEPROM.
Signed-off-by: Meir Lichtinger <meirl@mellanox.com>
CC: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the tx path of l2tp, l2tp_xmit_skb() calls skb_dst_set() to set
skb's dst. However, it will eventually call inet6_csk_xmit() or
ip_queue_xmit() where skb's dst will be overwritten by:
skb_dst_set_noref(skb, dst);
without releasing the old dst in skb. Then it causes dst/dev refcnt leak:
unregister_netdevice: waiting for eth0 to become free. Usage count = 1
This can be reproduced by simply running:
# modprobe l2tp_eth && modprobe l2tp_ip
# sh ./tools/testing/selftests/net/l2tp.sh
So before going to inet6_csk_xmit() or ip_queue_xmit(), skb's dst
should be dropped. This patch is to fix it by removing skb_dst_set()
from l2tp_xmit_skb() and moving skb_dst_drop() into l2tp_xmit_core().
Fixes: 3557baabf2 ("[L2TP]: PPP over L2TP driver core")
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: James Chapman <jchapman@katalix.com>
Tested-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 142240398e ("audit: add gfp parameter to audit_log_nfcfg")
incorrectly passed gfp flags to audit_log_nfcfg() which were not
consistent with the calling function, this commit fixes that.
Fixes: 142240398e ("audit: add gfp parameter to audit_log_nfcfg")
Reported-by: Jones Desougi <jones.desougi+netfilter@gmail.com>
Reviewed-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter updates for net-next:
1) Support for rejecting packets from the prerouting chain, from
Laura Garcia Liebana.
2) Remove useless assignment in pipapo, from Stefano Brivio.
3) On demand hook registration in IPVS, from Julian Anastasov.
4) Expire IPVS connection from process context to not overload
timers, also from Julian.
5) Fallback to conntrack TCP tracker to handle connection reuse
in IPVS, from Julian Anastasov.
6) Several patches to support for chain bindings.
7) Expose enum nft_chain_flags through UAPI.
8) Reject unsupported chain flags from the netlink control plane.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn