When SRIOV commands are executed over the comm-channel and get
a fatal error (e.g. timeout, closing command failure) the VF enters
into error state and reset flow is activated.
To be able to recognize whether the failure was on a closing command, the
operational code for the given VHCR command is used. Once the device entered
into an error state we prevent redundant error messages from being printed.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We activate reset flow upon command fatal errors, when the device enters an
erroneous state, and must be reset.
The cases below are assumed to be fatal: FW command timed-out, an error from FW
on closing commands, pci is offline when posting/pending a command.
In those cases we place the device into an error state: chip is reset, pending
commands are awakened and completed immediately. Subsequent commands will
return immediately.
The return code in the above cases will depend on the command. Commands which
free and close resources will return success (because the chip was reset, so
callers may safely free their kernel resources). Other commands will return -EIO.
Since the device's state was marked as error, the catas poller will
detect this and restart the device's software stack (as is done when a FW
internal error is directly detected). The device state is protected by a
persistent mutex lives on its mlx4_dev, as such no need any more for the
hcr_mutex which is removed.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a given flow steering rule is invalid in respect to the current
steering configuration, print the correct error message to the system log.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If mlx4_ib_create_flow() attempts to create > 1 rules with the
firmware, and one of these registrations fail, we leaked the
already created flow rules.
One example of the leak is when the registration of the VXLAN ghost
steering rule fails, we didn't unregister the original rule requested
by the user, introduced in commit d2fce8a906 "mlx4: Set
user-space raw Ethernet QPs to properly handle VXLAN traffic".
While here, add dump of the VXLAN portion of steering rules
so it can actually be seen when flow creation fails.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the function which we use to set VXLAN DMFS (flow-steering) rules
from mlx4_en to mlx4_core. This refactoring will allow the mlx4_ib driver
to call the helper for the use case of user-space RAW Ethernet QPs, such
that they can serve VXLAN traffic too.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In B0 steering mode if promiscuous QP asks to be detached from MCG entry,
and it is the only one in this entry then the entry will never be deleted.
This is a wrong behavior since we don't want to keep those entries after
the promiscuous QP becomes non-promiscuous. Therefore remove steering
entry containing only promiscuous QP.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In current situation host is adding the promiscuous QP to all steering
entries and the default entry as well. In this case when having PV
and SR-IOV on the same setup bridge will receive all traffic that is
targeted to the other VMs. This is bad.
Solution: In SR-IOV mode host can add promiscuous QP to default entry only.
The above problem and fix are relevant for B0 steering mode only.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In B0 steering mode when adding QPs to the default MCG entry need
to check that maximal number of QPs per MCG entry was not exceeded.
Signed-off-by: Alexander Guller <alexg@mellanox.com>
Reviewed-by: Aviad Yehezkel <aviadye@mellanox.co.il>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To make sure that the array index isn't used in the code with
negative value, we stop using the for loop integer iterator
outside of it.
>From now on use members count to swap the last QP with removed one.
Fix also the second occurrence of this flow in mlx4_qp_detach_common().
In mlx4_qp_detach_common() use members_count instead of
loop iterator outside of the for loop.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing multicast address in B0 steering mode there is
a bug in cases where there is a single QP registered for the address,
and this QP is also promiscuous. In such cases the entry wouldn't be
deleted from the SW structure representing all Ethernet MCG entries,
but would be removed in HW. This way when driver goes to remove it
from SW and HW structures the HW deletion fails.
Moreover the same index could later be used for registering
different address, which can be Infiniband.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adopt the "info: why not propagate 'ret' from parse_trans_rule()..."
suggestion made by the smatch semantic checker on:
drivers/net/ethernet/mellanox/mlx4/mcg.c:867 mlx4_flow_attach()
Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a more current logging style.
o Coalesce formats
o Add missing spaces for coalesced formats
o Align arguments for modified formats
o Add missing newlines for some logging messages
o Use DRV_NAME as part of format instead of %s, DRV_NAME to
reduce overall text.
o Use ..., ##__VA_ARGS__ instead of args... in macros
o Correct a few format typos
o Use a single line message where appropriate
Signed-off-by: Joe Perches <joe@perches.com>
Acked-By: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for N-Port VFs, this includes:
1. Adding support in the wrapped FW command
In wrapped commands, we need to verify and convert
the slave's port into the real physical port.
Furthermore, when sending the response back to the slave,
a reverse conversion should be made.
2. Adjusting sqpn for QP1 para-virtualization
The slave assumes that sqpn is used for QP1 communication.
If the slave is assigned to a port != (first port), we need
to adjust the sqpn that will direct its QP1 packets into the
correct endpoint.
3. Adjusting gid[5] to modify the port for raw ethernet
In B0 steering, gid[5] contains the port. It needs
to be adjusted into the physical port.
4. Adjusting number of ports in the query / ports caps in the FW commands
When a slave queries the hardware, it needs to view only
the physical ports it's assigned to.
5. Adjusting the sched_qp according to the port number
The QP port is encoded in the sched_qp, thus in modify_qp we need
to encode the correct port in sched_qp.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) BPF debugger and asm tool by Daniel Borkmann.
2) Speed up create/bind in AF_PACKET, also from Daniel Borkmann.
3) Correct reciprocal_divide and update users, from Hannes Frederic
Sowa and Daniel Borkmann.
4) Currently we only have a "set" operation for the hw timestamp socket
ioctl, add a "get" operation to match. From Ben Hutchings.
5) Add better trace events for debugging driver datapath problems, also
from Ben Hutchings.
6) Implement auto corking in TCP, from Eric Dumazet. Basically, if we
have a small send and a previous packet is already in the qdisc or
device queue, defer until TX completion or we get more data.
7) Allow userspace to manage ipv6 temporary addresses, from Jiri Pirko.
8) Add a qdisc bypass option for AF_PACKET sockets, from Daniel
Borkmann.
9) Share IP header compression code between Bluetooth and IEEE802154
layers, from Jukka Rissanen.
10) Fix ipv6 router reachability probing, from Jiri Benc.
11) Allow packets to be captured on macvtap devices, from Vlad Yasevich.
12) Support tunneling in GRO layer, from Jerry Chu.
13) Allow bonding to be configured fully using netlink, from Scott
Feldman.
14) Allow AF_PACKET users to obtain the VLAN TPID, just like they can
already get the TCI. From Atzm Watanabe.
15) New "Heavy Hitter" qdisc, from Terry Lam.
16) Significantly improve the IPSEC support in pktgen, from Fan Du.
17) Allow ipv4 tunnels to cache routes, just like sockets. From Tom
Herbert.
18) Add Proportional Integral Enhanced packet scheduler, from Vijay
Subramanian.
19) Allow openvswitch to mmap'd netlink, from Thomas Graf.
20) Key TCP metrics blobs also by source address, not just destination
address. From Christoph Paasch.
21) Support 10G in generic phylib. From Andy Fleming.
22) Try to short-circuit GRO flow compares using device provided RX
hash, if provided. From Tom Herbert.
The wireless and netfilter folks have been busy little bees too.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2064 commits)
net/cxgb4: Fix referencing freed adapter
ipv6: reallocate addrconf router for ipv6 address when lo device up
fib_frontend: fix possible NULL pointer dereference
rtnetlink: remove IFLA_BOND_SLAVE definition
rtnetlink: remove check for fill_slave_info in rtnl_have_link_slave_info
qlcnic: update version to 5.3.55
qlcnic: Enhance logic to calculate msix vectors.
qlcnic: Refactor interrupt coalescing code for all adapters.
qlcnic: Update poll controller code path
qlcnic: Interrupt code cleanup
qlcnic: Enhance Tx timeout debugging.
qlcnic: Use bool for rx_mac_learn.
bonding: fix u64 division
rtnetlink: add missing IFLA_BOND_AD_INFO_UNSPEC
sfc: Use the correct maximum TX DMA ring size for SFC9100
Add Shradha Shah as the sfc driver maintainer.
net/vxlan: Share RX skb de-marking and checksum checks with ovs
tulip: cleanup by using ARRAY_SIZE()
ip_tunnel: clear IPCB in ip_tunnel_xmit() in case dst_link_failure() is called
net/cxgb4: Don't retrieve stats during recovery
...
This is a fix to a regression introduced by commit:
"982290a net/mlx4_core: Check port number for validity
before accessing data"
IPoIB could not attach to multicast group and we get this in dmesg:
[144214.145008] ib0: failed to attach to multicast group, ret = -22
[144214.145016] ib0: couldn't attach QP to multicast group ff12:401b:ffff:0000:0000:0000:ffff:ffff
[144214.145019] ib0: multicast join failed for ff12:401b:ffff:0000:0000:0000:ffff:ffff, status -22
The cause to the problem is because port is extracted from gid[5].
Which is only valid for Ethernet.
Removed this validation in mlx4_qp_attach_common(), which is accessed
from both Ethernet and IB flows.
Error flow for bad port value in Ethernet is already exists in that
function.
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for allocating IB UD QPs that we can steer
traffic from. We introduce a new firmware command FLOW_STEERING_IB_UC_QP_RANGE
and a capability bit.
This command isn't supported for VFs.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add the low-level device commands and definitions used for TCP/IP HW offloads
of tunneled/vxlan traffic which are supported by the ConnectX3-pro NIC.
This is done through the following elements:
- read tunneling device caps in QUERY_DEV_CAP
- add helper function to do SET_PORT for tunneling
- add DMFS VXLAN steering rule definitions
- add CQE and WQE checksum offload field definitions
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to validate port number at mlx4_promisc_qp() before use.
Since port number is extracted from gid, as a cooked or corrupted gid
could lead to a crash.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f4ec9e9 "mlx4_core: Change bitmap allocator to work in round-robin fashion"
introduced round-robin allocation (via bitmap) for all resources which allocate
via a bitmap.
Round robin allocation is desirable for mcgs, counters, pd's, UARs, and xrcds.
These are simply numbers, with no involvement of ICM memory mapping.
Round robin is required for QPs, since we had a problem with immediate
reuse of a 24-bit QP number (commit f4ec9e9).
However, for other resources which use the bitmap allocator and involve
mapping ICM memory -- MPTs, CQs, SRQs -- round-robin is not desirable.
What happens in these cases is the following:
ICM memory is allocated and mapped in chunks of 256K.
Since the resource allocation index goes up monotonically, the allocator
will eventually require mapping a new chunk. Now, chunks are also unmapped
when their reference count goes back to zero. Thus, if a single app is
running and starts/exits frequently we will have the following situation:
When the app starts, a new chunk must be allocated and mapped.
When the app exits, the chunk reference count goes back to zero, and the
chunk is unmapped and freed. Therefore, the app must pay the cost of allocation
and mapping of ICM memory each time it runs (although the price is paid only when
allocating the initial entry in the new chunk).
For apps which allocate MPTs/SRQs/CQs and which operate as described above,
this presented a performance problem.
We therefore roll back the round-robin allocator modification for MPTs, CQs, SRQs.
Reported-by: Matthew Finlay <matt@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To guarantee that all unused fields in all FW commands for both inboxes
and outboxes are zeroed out, initialize the mailbox buffer to all zeroes.
This is especially important for SRIOV comm-channel virtual commands
(such as QUERY_FUNC_CAP), where if new fields are added to support new
features, the driver can depend on older kernels passing zeroes in these
fields.
In addition to zeroing out the mailbox buffer at allocation time, all
(now unnecessary) calls to memset by the callers of
mlx4_alloc_cmd_mailbox() are removed.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove code that triggers trivial build warnings.
drivers/net/ethernet/mellanox/mlx4/cmd.c: In function ‘mlx4_set_vf_vlan’:
drivers/net/ethernet/mellanox/mlx4/cmd.c:2256: warning: variable ‘vf_oper’ set but not used
drivers/net/ethernet/mellanox/mlx4/mcg.c: In function ‘mlx4_map_sw_to_hw_steering_mode’:
drivers/net/ethernet/mellanox/mlx4/mcg.c:648: warning: comparison of unsigned expression < 0 is always false
drivers/net/ethernet/mellanox/mlx4/mcg.c: In function ‘mlx4_map_sw_to_hw_steering_id’:
drivers/net/ethernet/mellanox/mlx4/mcg.c:685: warning: comparison of unsigned expression < 0 is always false
drivers/net/ethernet/mellanox/mlx4/mcg.c: In function ‘mlx4_hw_rule_sz’:
drivers/net/ethernet/mellanox/mlx4/mcg.c:712: warning: comparison of unsigned expression < 0 is always false
drivers/net/ethernet/mellanox/mlx4/fw.c: In function ‘mlx4_opreq_action’:
drivers/net/ethernet/mellanox/mlx4/fw.c:1732: warning: variable ‘type_m’ set but not used
drivers/net/ethernet/mellanox/mlx4/srq.c:302: warning: no previous prototype for ‘mlx4_srq_lookup’
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds new firmware command and new firmware event. The firmware
raises the MLX4_EVENT_TYPE_OP_REQUIRED event in order to signal the driver it
needs to perform an administrative operation throughout the MLX4_CMD_GET_OP_REQ
command. At the moment the supported operation is adding/removing multicast
entries which are used by the firmware for handling NCSI traffic in B0
steering mode.
Also, had to swap the order of mlx4_init_mcg_table() and
mlx4_init_eq_table() to make sure that driver will get events only after
resources are initialized to handle it.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- XRC transport fixes
- Fix DHCP on IPoIB
- mlx4 preparations for flow steering
- iSER fixes
- miscellaneous other fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=1ojD
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull InfiniBand/RDMA changes from Roland Dreier:
- XRC transport fixes
- Fix DHCP on IPoIB
- mlx4 preparations for flow steering
- iSER fixes
- miscellaneous other fixes
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (23 commits)
IB/iser: Add support for iser CM REQ additional info
IB/iser: Return error to upper layers on EAGAIN registration failures
IB/iser: Move informational messages from error to info level
IB/iser: Add module version
mlx4_core: Expose a few helpers to fill DMFS HW strucutures
mlx4_core: Directly expose fields of DMFS HW rule control segment
mlx4_core: Change a few DMFS fields names to match firmare spec
mlx4: Match DMFS promiscuous field names to firmware spec
mlx4_core: Move DMFS HW structs to common header file
IB/mlx4: Set link type for RAW PACKET QPs in the QP context
IB/mlx4: Disable VLAN stripping for RAW PACKET QPs
mlx4_core: Reduce warning message for SRQ_LIMIT event to debug level
RDMA/iwcm: Don't touch cmid after dropping reference
IB/qib: Correct qib_verbs_register_sysfs() error handling
IB/ipath: Correct ipath_verbs_register_sysfs() error handling
RDMA/cxgb4: Fix SQ allocation when on-chip SQ is disabled
SRPT: Fix odd use of WARN_ON()
IPoIB: Fix ipoib_hard_header() return value
RDMA: Rename random32() to prandom_u32()
RDMA/cxgb3: Fix uninitialized variable
...
Re-arrange some of code which fills DMFS HW structures so we can use
it from within the core driver and from the IB driver too, e.g when
verbs DMFS structures are transformed into mlx4 hardware structs.
Also, add struct mlx4_flow_handle struct which will be of use by the
DMFS verbs flow in the IB driver.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Some of struct mlx4_net_trans_rule_hw_ctrl fields were packed into u32
and accessed through bit field operations. Expose and access them
directly as u8 or u16.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Change struct mlx4_net_trans_rule_hw_eth :: vlan_id name to vlan_tag
Change struct mlx4_net_trans_rule_hw_ib :: r_u_qpn name to l3_qpn
The patch doesn't introduce any functional change or API change
towards the firmware.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Align the names used by enum mlx4_net_trans_promisc_mode with the
actual firmware specification. The patch doesn't introduce any
functional change or API change towards the firmware.
Remove MLX4_FS_PROMISC_FUNCTION_PORT which isn't of use. Add new
enums MLX4_FS_{UC/MC}_SNIFFER as a preparation step for sniffer
support.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
A pre-step for supporting guests that use B0 steering over a hypervisor
that runs in DMFS (device managed flow steering mode). Add helper function
which allows to translate L2 attachments / detachments provided in B0 mode
to DMFS rules.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The allow_loopback flag was wrongly set using arithmetic bit operation, change
the code to use logical bit operation.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the fields for struct mlx4_net_trans_rule_hw_ctrl were packed into u32
and accessed through bit field operations. Expose and access them directly as
u8.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device managed flow steering will be enabled only under administrator
directive provided through setting the existing module parameter
log_num_mgm_entry_size to -1 (if the device actually supports flow
steering). If flow steering isn't requested or not available, the
driver will use the value of log_num_mgm_entry_size and B0 steering.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The search for promisc entries was always done on the first port,
While the addition is done on the correct port.
This lead to resource leackage of promisc entries on the second
port and brought to a state where we could no longer enter to
promiscuous mode after enough iterations of "ifconfig promisc"
on the second port.
Fix that by using the correct port when searching.
Reported-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To allow for usage of the flow steering Firmware structures in more locations over the driver,
such as the resource tracker, move them from mcg.c to common header files.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert a 0 error return code to a negative one, as returned elsewhere in the
function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret;
expression e,e1,e2,e3,e4,x;
@@
(
if (\(ret != 0\|ret < 0\) || ...) { ... return ...; }
|
ret = 0
)
... when != ret = e1
*x = \(kmalloc\|kzalloc\|kcalloc\|devm_kzalloc\|ioremap\|ioremap_nocache\|devm_ioremap\|devm_ioremap_nocache\)(...);
... when != x = e2
when != ret = e3
*if (x == NULL || ...)
{
... when != ret = e4
* return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define this macro is one common place instead of duplicating it over the code
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This should be ">=" here instead of ">". MLX4_NET_TRANS_RULE_NUM is 6.
We use "spec->id" as an array offset into the __rule_hw_sz[] and
__sw_id_hw[] arrays which have 6 elements.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device managed flow steering API has three promiscuous modes:
1. Uplink - captures all the packets that arrive to the port.
2. Allmulti - captures all multicast packets arriving to the port.
3. Function port - for future use, this mode is not implemented yet.
Use these modes with the flow_attach and flow_detach firmware commands
according to the promiscuous state of the netdevice.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver is modified to support three operation modes.
If supported by firmware use the device managed flow steering
API, that which we call device managed steering mode. Else, if
the firmware supports the B0 steering mode use it, and finally,
if none of the above, use the A0 steering mode.
When the steering mode is device managed, the code is modified
such that L2 based rules set by the mlx4_en driver for Ethernet
unicast and multicast, and the IB stack multicast attach calls
done through the mlx4_ib driver are all routed to use the device
managed API.
When attaching rule using device managed flow steering API,
the firmware returns a 64 bit registration id, which is to be
provided during detach.
Currently the firmware is always programmed during HCA initialization
to use standard L2 hashing. Future work should be done to allow
configuring the flow-steering hash function with common, non
proprietary means.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for firmware commands to attach/detach a new device managed
steering mode. Such network steering rules allow the user to provide an
L2/L3/L4 flow specification to the firmware and have the device to steer
traffic that matches that specification to the provided QP.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of checking the firmware supported steering mode in various
places in the code, add a dedicated field in the mlx4 device capabilities
structure which is written once during the initialization flow and read
across the code.
This also set the grounds for add new steering modes. Currently two modes
are supported, and are named after the ConnectX HW versions A0 and B0.
A0 steering uses mac_index, vlan_index and priority to steer traffic
into pre-defined range of QPs.
B0 steering uses Ethernet L2 hashing rules and is enabled only
if the firmware supports both unicast and multicast B0 steering,
The current steering modes are relevant for Ethernet traffic only,
such that Infiniband steering remains untouched.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle the compiler warnings on variables which are set but not used
by removing the relevant variable or casting a return value which is
ignored on purpose to void.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_multicast_attach/detach() should use always MLX4_MC_STEER flag
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_qp_attach/detach_common() don't use hash variable, move it to find_entry()
static find_entry() in mcg.c doesn't use steer argument
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use port number for correct steering (list per port).
Before the fix all steering entries (for both physical ports)
were managed in first port structures, so we had leakage of resources
for port 2.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use MLX4_DEV_CAP_FLAG_VEP_UC_STEER for unicast_promisc_add/remove
Unicast entries were managed in wrong data structures.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The physical port is now common to the PF and VFs.
The port resources and configuration is managed by the PF, VFs can
only influence the MTU of the port, it is set as max among all functions,
Each function allocates RX buffers of required size to meet it's MTU enforcement.
Port management code was moved to mlx4_core, as the mlx4_en module is
virtualization unaware
Move handling qp functionality to mlx4_get_eth_qp/mlx4_put_eth_qp
including reserve/release range and add/release unicast steering.
Let mlx4_register/unregister_mac deal only with MAC (un)registration.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let multicast/unicast attaching flow go through resource tracker.
The PF is the one responsible for managing all the steering entries.
Define and use module parameter that determines the number of qps
per multicast group.
Minor changes in function calls according to changed prototype.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
For SRIOV, some Hypervisor commands can be executed directly (native = 1).
Others should go through the command wrapper flow (for tracking resource
usage, for example, or for changing some HCA configurations that slaves
need to be notified of).
This patch sets the groundwork for this capability -- adding the correct
value of "native" in each case.
Note that if SRIOV is not activated, this parameter has no effect.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
These were getting the macros from an implicit module.h
include via device.h, but we are planning to clean that up.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
drivers/net: Add export.h to wireless/brcm80211/brcmfmac/bcmsdh.c
This relatively recently added file uses EXPORT_SYMBOL and hence
needs export.h included so that it is compatible with the module.h
split up work.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Moves the Mellanox driver into drivers/net/ethernet/mellanox/ and
make the necessary Kconfig and Makefile changes.
CC: Roland Dreier <roland@kernel.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Yishai Hadas