When I run a parallel reading performan testing on a md raid1 device with
two NVMe SSDs, I observe very bad throughput in supprise: by fio with 64KB
block size, 40 seq read I/O jobs, 128 iodepth, overall throughput is
only 2.7GB/s, this is around 50% of the idea performance number.
The perf reports locking contention happens at allow_barrier() and
wait_barrier() code,
- 41.41% fio [kernel.kallsyms] [k] _raw_spin_lock_irqsave
- _raw_spin_lock_irqsave
+ 89.92% allow_barrier
+ 9.34% __wake_up
- 37.30% fio [kernel.kallsyms] [k] _raw_spin_lock_irq
- _raw_spin_lock_irq
- 100.00% wait_barrier
The reason is, in these I/O barrier related functions,
- raise_barrier()
- lower_barrier()
- wait_barrier()
- allow_barrier()
They always hold conf->resync_lock firstly, even there are only regular
reading I/Os and no resync I/O at all. This is a huge performance penalty.
The solution is a lockless-like algorithm in I/O barrier code, and only
holding conf->resync_lock when it has to.
The original idea is from Hannes Reinecke, and Neil Brown provides
comments to improve it. I continue to work on it, and make the patch into
current form.
In the new simpler raid1 I/O barrier implementation, there are two
wait barrier functions,
- wait_barrier()
Which calls _wait_barrier(), is used for regular write I/O. If there is
resync I/O happening on the same I/O barrier bucket, or the whole
array is frozen, task will wait until no barrier on same barrier bucket,
or the whold array is unfreezed.
- wait_read_barrier()
Since regular read I/O won't interfere with resync I/O (read_balance()
will make sure only uptodate data will be read out), it is unnecessary
to wait for barrier in regular read I/Os, waiting in only necessary
when the whole array is frozen.
The operations on conf->nr_pending[idx], conf->nr_waiting[idx], conf->
barrier[idx] are very carefully designed in raise_barrier(),
lower_barrier(), _wait_barrier() and wait_read_barrier(), in order to
avoid unnecessary spin locks in these functions. Once conf->
nr_pengding[idx] is increased, a resync I/O with same barrier bucket index
has to wait in raise_barrier(). Then in _wait_barrier() if no barrier
raised in same barrier bucket index and array is not frozen, the regular
I/O doesn't need to hold conf->resync_lock, it can just increase
conf->nr_pending[idx], and return to its caller. wait_read_barrier() is
very similar to _wait_barrier(), the only difference is it only waits when
array is frozen. For heavy parallel reading I/Os, the lockless I/O barrier
code almostly gets rid of all spin lock cost.
This patch significantly improves raid1 reading peroformance. From my
testing, a raid1 device built by two NVMe SSD, runs fio with 64KB
blocksize, 40 seq read I/O jobs, 128 iodepth, overall throughput
increases from 2.7GB/s to 4.6GB/s (+70%).
Changelog
V4:
- Change conf->nr_queued[] to atomic_t.
- Define BARRIER_BUCKETS_NR_BITS by (PAGE_SHIFT - ilog2(sizeof(atomic_t)))
V3:
- Add smp_mb__after_atomic() as Shaohua and Neil suggested.
- Change conf->nr_queued[] from atomic_t to int.
- Change conf->array_frozen from atomic_t back to int, and use
READ_ONCE(conf->array_frozen) to check value of conf->array_frozen
in _wait_barrier() and wait_read_barrier().
- In _wait_barrier() and wait_read_barrier(), add a call to
wake_up(&conf->wait_barrier) after atomic_dec(&conf->nr_pending[idx]),
to fix a deadlock between _wait_barrier()/wait_read_barrier and
freeze_array().
V2:
- Remove a spin_lock/unlock pair in raid1d().
- Add more code comments to explain why there is no racy when checking two
atomic_t variables at same time.
V1:
- Original RFC patch for comments.
Signed-off-by: Coly Li <colyli@suse.de>
Cc: Shaohua Li <shli@fb.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Guoqing Jiang <gqjiang@suse.com>
Reviewed-by: Neil Brown <neilb@suse.de>
Signed-off-by: Shaohua Li <shli@fb.com>
'Commit 79ef3a8aa1 ("raid1: Rewrite the implementation of iobarrier.")'
introduces a sliding resync window for raid1 I/O barrier, this idea limits
I/O barriers to happen only inside a slidingresync window, for regular
I/Os out of this resync window they don't need to wait for barrier any
more. On large raid1 device, it helps a lot to improve parallel writing
I/O throughput when there are background resync I/Os performing at
same time.
The idea of sliding resync widow is awesome, but code complexity is a
challenge. Sliding resync window requires several variables to work
collectively, this is complexed and very hard to make it work correctly.
Just grep "Fixes: 79ef3a8aa1" in kernel git log, there are 8 more patches
to fix the original resync window patch. This is not the end, any further
related modification may easily introduce more regreassion.
Therefore I decide to implement a much simpler raid1 I/O barrier, by
removing resync window code, I believe life will be much easier.
The brief idea of the simpler barrier is,
- Do not maintain a global unique resync window
- Use multiple hash buckets to reduce I/O barrier conflicts, regular
I/O only has to wait for a resync I/O when both them have same barrier
bucket index, vice versa.
- I/O barrier can be reduced to an acceptable number if there are enough
barrier buckets
Here I explain how the barrier buckets are designed,
- BARRIER_UNIT_SECTOR_SIZE
The whole LBA address space of a raid1 device is divided into multiple
barrier units, by the size of BARRIER_UNIT_SECTOR_SIZE.
Bio requests won't go across border of barrier unit size, that means
maximum bio size is BARRIER_UNIT_SECTOR_SIZE<<9 (64MB) in bytes.
For random I/O 64MB is large enough for both read and write requests,
for sequential I/O considering underlying block layer may merge them
into larger requests, 64MB is still good enough.
Neil also points out that for resync operation, "we want the resync to
move from region to region fairly quickly so that the slowness caused
by having to synchronize with the resync is averaged out over a fairly
small time frame". For full speed resync, 64MB should take less then 1
second. When resync is competing with other I/O, it could take up a few
minutes. Therefore 64MB size is fairly good range for resync.
- BARRIER_BUCKETS_NR
There are BARRIER_BUCKETS_NR buckets in total, which is defined by,
#define BARRIER_BUCKETS_NR_BITS (PAGE_SHIFT - 2)
#define BARRIER_BUCKETS_NR (1<<BARRIER_BUCKETS_NR_BITS)
this patch makes the bellowed members of struct r1conf from integer
to array of integers,
- int nr_pending;
- int nr_waiting;
- int nr_queued;
- int barrier;
+ int *nr_pending;
+ int *nr_waiting;
+ int *nr_queued;
+ int *barrier;
number of the array elements is defined as BARRIER_BUCKETS_NR. For 4KB
kernel space page size, (PAGE_SHIFT - 2) indecates there are 1024 I/O
barrier buckets, and each array of integers occupies single memory page.
1024 means for a request which is smaller than the I/O barrier unit size
has ~0.1% chance to wait for resync to pause, which is quite a small
enough fraction. Also requesting single memory page is more friendly to
kernel page allocator than larger memory size.
- I/O barrier bucket is indexed by bio start sector
If multiple I/O requests hit different I/O barrier units, they only need
to compete I/O barrier with other I/Os which hit the same I/O barrier
bucket index with each other. The index of a barrier bucket which a
bio should look for is calculated by sector_to_idx() which is defined
in raid1.h as an inline function,
static inline int sector_to_idx(sector_t sector)
{
return hash_long(sector >> BARRIER_UNIT_SECTOR_BITS,
BARRIER_BUCKETS_NR_BITS);
}
Here sector_nr is the start sector number of a bio.
- Single bio won't go across boundary of a I/O barrier unit
If a request goes across boundary of barrier unit, it will be split. A
bio may be split in raid1_make_request() or raid1_sync_request(), if
sectors returned by align_to_barrier_unit_end() is smaller than
original bio size.
Comparing to single sliding resync window,
- Currently resync I/O grows linearly, therefore regular and resync I/O
will conflict within a single barrier units. So the I/O behavior is
similar to single sliding resync window.
- But a barrier unit bucket is shared by all barrier units with identical
barrier uinit index, the probability of conflict might be higher
than single sliding resync window, in condition that writing I/Os
always hit barrier units which have identical barrier bucket indexs with
the resync I/Os. This is a very rare condition in real I/O work loads,
I cannot imagine how it could happen in practice.
- Therefore we can achieve a good enough low conflict rate with much
simpler barrier algorithm and implementation.
There are two changes should be noticed,
- In raid1d(), I change the code to decrease conf->nr_pending[idx] into
single loop, it looks like this,
spin_lock_irqsave(&conf->device_lock, flags);
conf->nr_queued[idx]--;
spin_unlock_irqrestore(&conf->device_lock, flags);
This change generates more spin lock operations, but in next patch of
this patch set, it will be replaced by a single line code,
atomic_dec(&conf->nr_queueud[idx]);
So we don't need to worry about spin lock cost here.
- Mainline raid1 code split original raid1_make_request() into
raid1_read_request() and raid1_write_request(). If the original bio
goes across an I/O barrier unit size, this bio will be split before
calling raid1_read_request() or raid1_write_request(), this change
the code logic more simple and clear.
- In this patch wait_barrier() is moved from raid1_make_request() to
raid1_write_request(). In raid_read_request(), original wait_barrier()
is replaced by raid1_read_request().
The differnece is wait_read_barrier() only waits if array is frozen,
using different barrier function in different code path makes the code
more clean and easy to read.
Changelog
V4:
- Add alloc_r1bio() to remove redundant r1bio memory allocation code.
- Fix many typos in patch comments.
- Use (PAGE_SHIFT - ilog2(sizeof(int))) to define BARRIER_BUCKETS_NR_BITS.
V3:
- Rebase the patch against latest upstream kernel code.
- Many fixes by review comments from Neil,
- Back to use pointers to replace arraries in struct r1conf
- Remove total_barriers from struct r1conf
- Add more patch comments to explain how/why the values of
BARRIER_UNIT_SECTOR_SIZE and BARRIER_BUCKETS_NR are decided.
- Use get_unqueued_pending() to replace get_all_pendings() and
get_all_queued()
- Increase bucket number from 512 to 1024
- Change code comments format by review from Shaohua.
V2:
- Use bio_split() to split the orignal bio if it goes across barrier unit
bounday, to make the code more simple, by suggestion from Shaohua and
Neil.
- Use hash_long() to replace original linear hash, to avoid a possible
confilict between resync I/O and sequential write I/O, by suggestion from
Shaohua.
- Add conf->total_barriers to record barrier depth, which is used to
control number of parallel sync I/O barriers, by suggestion from Shaohua.
- In V1 patch the bellowed barrier buckets related members in r1conf are
allocated in memory page. To make the code more simple, V2 patch moves
the memory space into struct r1conf, like this,
- int nr_pending;
- int nr_waiting;
- int nr_queued;
- int barrier;
+ int nr_pending[BARRIER_BUCKETS_NR];
+ int nr_waiting[BARRIER_BUCKETS_NR];
+ int nr_queued[BARRIER_BUCKETS_NR];
+ int barrier[BARRIER_BUCKETS_NR];
This change is by the suggestion from Shaohua.
- Remove some inrelavent code comments, by suggestion from Guoqing.
- Add a missing wait_barrier() before jumping to retry_write, in
raid1_make_write_request().
V1:
- Original RFC patch for comments
Signed-off-by: Coly Li <colyli@suse.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Guoqing Jiang <gqjiang@suse.com>
Reviewed-by: Neil Brown <neilb@suse.de>
Signed-off-by: Shaohua Li <shli@fb.com>
Firstly bio_clone_mddev() is used in raid normal I/O and isn't
in resync I/O path.
Secondly all the direct access to bvec table in raid happens on
resync I/O except for write behind of raid1, in which we still
use bio_clone() for allocating new bvec table.
So this patch replaces bio_clone() with bio_clone_fast()
in bio_clone_mddev().
Also kill bio_clone_mddev() and call bio_clone_fast() directly, as
suggested by Christoph Hellwig.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Write behind need to replace pages in bio's bvecs, and we have
to clone a fresh bio with new bvec table, so use the introduced
bio_clone_bioset_partial() for it.
For other bio_clone_mddev() cases, we will use fast clone since
they don't need to touch bvec table.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Shaohua Li <shli@fb.com>
We will want to have struct backing_dev_info allocated separately from
struct request_queue. As the first step add pointer to backing_dev_info
to request_queue and convert all users touching it. No functional
changes in this patch.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@fb.com>
No need for the local variables, the bio is still live and we can just
assign the bits we want directly. Make me wonder why we can't assign
all the bio flags to start with.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Commit 6995f0b (md: takeover should clear unrelated bits) clear
unrelated bits, but it's quite fragile. To avoid error in the future,
define a macro for unsupported mddev flags for each raid type and use it
to clear unsupported mddev flags. This should be less error-prone.
Suggested-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Refactor raid1_make_request to make read and write code in their own
functions to clean up the code.
Signed-off-by: Robert LeBlanc <robert@leblancnet.us>
Signed-off-by: Shaohua Li <shli@fb.com>
The mddev->flags are used for different purposes. There are a lot of
places we check/change the flags without masking unrelated flags, we
could check/change unrelated flags. These usage are most for superblock
write, so spearate superblock related flags. This should make the code
clearer and also fix real bugs.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
When we change level from raid1 to raid5, the MD_FAILFAST_SUPPORTED bit
will be accidentally set, but raid5 doesn't support it. The same is true
for the MD_HAS_JOURNAL bit.
Fix: 46533ff (md: Use REQ_FAILFAST_* on metadata writes where appropriate)
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
When writing to a fastfail device we use MD_FASTFAIL unless
it is the only device being written to.
For resync/recovery, assume there was a working device to
read from so always use REQ_FASTFAIL_DEV.
If a write for resync/recovery fails, we just fail the
device - there is not much else to do.
If a normal failfast write fails, but the device cannot be
failed (must be only one left), we queue for write error
handling. This will call narrow_write_error() to retry the
write synchronously and without any FAILFAST flags.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
If a device is marked FailFast and it is not the only device
we can read from, we mark the bio with REQ_FAILFAST_* flags.
If this does fail, we don't try read repair but just allow
failure. If it was the last device it doesn't fail of
course, so the retry happens on the same device - this time
without FAILFAST. A subsequent failure will not retry but
will just pass up the error.
During resync we may use FAILFAST requests and on a failure
we will simply use the other device(s).
During recovery we will only use FAILFAST in the unusual
case were there are multiple places to read from - i.e. if
there are > 2 devices. If we get a failure we will fail the
device and complete the resync/recovery with remaining
devices.
The new R1BIO_FailFast flag is set on read reqest to suggest
the a FAILFAST request might be acceptable. The rdev needs
to have FailFast set as well for the read to actually use
REQ_FAILFAST_*.
We need to know there are at least two working devices
before we can set R1BIO_FailFast, so we mustn't stop looking
at the first device we find. So the "min_pending == 0"
handling to not exit early, but too always choose the
best_pending_disk if min_pending == 0.
The spinlocked region in raid1_error() in enlarged to ensure
that if two bios, reading from two different devices, fail
at the same time, then there is no risk that both devices
will be marked faulty, leaving zero "In_sync" devices.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
This can only be supported on personalities which ensure
that md_error() never causes an array to enter the 'failed'
state. i.e. if marking a device Faulty would cause some
data to be inaccessible, the device is status is left as
non-Faulty. This is true for RAID1 and RAID10.
If we get a failure writing metadata but the device doesn't
fail, it must be the last device so we re-write without
FAILFAST to improve chance of success. We also flag the
device as LastDev so that future metadata updates don't
waste time on failfast writes.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Both raid1 and raid10 will sometimes delay handling an IO request,
such as when resync is happening or there are too many requests queued.
Add some blktrace messsages so we can see when that is happening when
looking for performance artefacts.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
The block tracing infrastructure (accessed with blktrace/blkparse)
supports the tracing of mapping bios from one device to another.
This is currently used when a bio in a partition is mapped to the
whole device, when bios are mapped by dm, and for mapping in md/raid5.
Other md personalities do not include this tracing yet, so add it.
When a read-error is detected we redirect the request to a different device.
This could justifiably be seen as a new mapping for the originial bio,
or a secondary mapping for the bio that errors. This patch uses
the second option.
When md is used under dm-raid, the mappings are not traced as we do
not have access to the block device number of the parent.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
While performing a resync/recovery, raid1 divides the
array space into three regions:
- before the resync
- at or shortly after the resync point
- much further ahead of the resync point.
Write requests to the first or third do not need to wait. Write
requests to the middle region do need to wait if resync requests are
pending.
If there are any active write requests in the middle region, resync
will wait for them.
Due to an accounting error, there is a small range of addresses,
between conf->next_resync and conf->start_next_window, where write
requests will *not* be blocked, but *will* be counted in the middle
region. This can effectively block resync indefinitely if filesystem
writes happen repeatedly to this region.
As ->next_window_requests is incremented when the sector is after
conf->start_next_window + NEXT_NORMALIO_DISTANCE
the same boundary should be used for determining when write requests
should wait.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
When writing to an array with a bitmap enabled, the writes are grouped
in batches which are preceded by an update to the bitmap.
It is quite likely if that a drive develops a problem which is not
media related, that the bitmap write will be the first to report an
error and cause the device to be marked faulty (as the bitmap write is
at the start of a batch).
In this case, there is point submiting the subsequent writes to the
failed device - that just wastes times.
So re-check the Faulty state of a device before submitting a
delayed write.
This requires that we keep the 'rdev', rather than the 'bdev' in the
bio, then swap in the bdev just before final submission.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
If write is the first operation on a disk and it happens not to be
aligned to page size, block layer sends read request first. If read
operation fails, the disk is set as failed as no attempt to fix the
error is made because array is in auto-readonly mode. Similarily, the
disk is set as failed for read-only array.
Take the same approach as in raid10. Don't fail the disk if array is in
readonly or auto-readonly mode. Try to redirect the request first and if
unsuccessful, return a read error.
Signed-off-by: Tomasz Majchrzak <tomasz.majchrzak@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
If a write error occurs, raid1 will try to rewrite the bio in small
chunk size. If the rewrite fails, raid1 will record the error in bad
block. narrow_write_error will always use WRITE for the bio, but
actually it could be a discard. Since discard bio hasn't payload, write
the bio will cause different issues. But discard error isn't fatal, we
can safely ignore it. This is what this patch does.
This issue should exist since discard is added, but only exposed with
recent arbitrary bio size feature.
Reported-and-tested-by: Sitsofe Wheeler <sitsofe@gmail.com>
Cc: stable@vger.kernel.org (v3.6)
Signed-off-by: Shaohua Li <shli@fb.com>
bio_free_pages is introduced in commit 1dfa0f68c0
("block: add a helper to free bio bounce buffer pages"),
we can reuse the func in other modules after it was
imported.
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Jens Axboe <axboe@fb.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Shaohua Li <shli@fb.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Acked-by: Kent Overstreet <kent.overstreet@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Since commit 63a4cc2486, bio->bi_rw contains flags in the lower
portion and the op code in the higher portions. This means that
old code that relies on manually setting bi_rw is most likely
going to be broken. Instead of letting that brokeness linger,
rename the member, to force old and out-of-tree code to break
at compile time instead of at runtime.
No intended functional changes in this commit.
Signed-off-by: Jens Axboe <axboe@fb.com>
These two are confusing leftover of the old world order, combining
values of the REQ_OP_ and REQ_ namespaces. For callers that don't
special case we mostly just replace bi_rw with bio_data_dir or
op_is_write, except for the few cases where a switch over the REQ_OP_
values makes more sense. Any check for READA is replaced with an
explicit check for REQ_RAHEAD. Also remove the READA alias for
REQ_RAHEAD.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Every time a device is removed with ->hot_remove_disk() a synchronize_rcu() call is made
which can delay several milliseconds in some case.
If lots of devices fail at once - as could happen with a large RAID10 where one set
of devices are removed all at once - these delays can add up to be very inconcenient.
As failure is not reversible we can check for that first, setting a
separate flag if it is found, and then all synchronize_rcu() once for
all the flagged devices. Then ->hot_remove_disk() function can skip the
synchronize_rcu() step if the flag is set.
fix build error(Shaohua)
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Since remove_and_add_spares() was added to hot_remove_disk() it has
been possible for an rdev to be hot-removed while fix_read_error()
was running, so we need to be more careful, and take a reference to
the rdev while performing IO.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
'mirror' is only used to find 'rdev', several times.
So just find 'rdev' once, and use it instead.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Both functions use conf->mirrors[mirror].rdev several times, so
improve readability by storing this in a local variable.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Re-checking the faulty flag here brings no value.
The comment about "risk" refers to the risk that the device could
be in the process of being removed by ->hot_remove_disk().
However providing that the ->nr_pending count is incremented inside
an rcu_read_locked() region, there is no risk of that happening.
This is because the rdev pointer (in the personalities array) is set
to NULL before synchronize_rcu(), and ->nr_pending is tested
afterwards. If the rcu_read_locked region happens before the
synchronize_rcu(), the test will see that nr_pending has been incremented.
If it happens afterwards, the rdev pointer will be NULL so there is nothing
to increment.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
A performance drop of mkfs has been observed on RAID10 during resync
since commit 09314799e4 ("md: remove 'go_faster' option from
->sync_request()"). Resync sends so many IOs it slows down non-resync
IOs significantly (few times). Add a short delay to a resync. The
previous long sleep (1s) has proven unnecessary, even very short delay
brings performance right.
The change also applied to raid1. The problem has not been observed on
raid1, however it shares barriers code with raid10 so it might be an
issue for some setup too.
Suggested-by: NeilBrown <neilb@suse.com>
Link: http://lkml.kernel.org/r/20160609134555.GA9104@proton.igk.intel.com
Signed-off-by: Tomasz Majchrzak <tomasz.majchrzak@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Instead of overloading the discard support with the REQ_SECURE flag.
Use the opportunity to rename the queue flag as well, and remove the
dead checks for this flag in the RAID 1 and RAID 10 drivers that don't
claim support for secure erase.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
To avoid confusion between REQ_OP_FLUSH, which is handled by
request_fn drivers, and upper layers requesting the block layer
perform a flush sequence along with possibly a WRITE, this patch
renames REQ_FLUSH to REQ_PREFLUSH.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Separate the op from the rq_flag_bits and have md
set/get the bio using bio_set_op_attrs/bio_op.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This has callers of submit_bio/submit_bio_wait set the bio->bi_rw
instead of passing it in. This makes that use the same as
generic_make_request and how we set the other bio fields.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Fixed up fs/ext4/crypto.c
Signed-off-by: Jens Axboe <axboe@fb.com>
Some code waits for a metadata update by:
1. flagging that it is needed (MD_CHANGE_DEVS or MD_CHANGE_CLEAN)
2. setting MD_CHANGE_PENDING and waking the management thread
3. waiting for MD_CHANGE_PENDING to be cleared
If the first two are done without locking, the code in md_update_sb()
which checks if it needs to repeat might test if an update is needed
before step 1, then clear MD_CHANGE_PENDING after step 2, resulting
in the wait returning early.
So make sure all places that set MD_CHANGE_PENDING are atomicial, and
bit_clear_unless (suggested by Neil) is introduced for the purpose.
Cc: Martin Kepplinger <martink@posteo.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: <linux-kernel@vger.kernel.org>
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
If first_bad == this_sector when we get the WriteMostly disk
in read_balance(), valid disk will be returned with zero
max_sectors. It'll lead to a dead loop in make_request(), and
OOM will happen because of endless allocation of struct bio.
Since we can't get data from this disk in this case, so
continue for another disk.
Signed-off-by: Wei Fang <fangwei1@huawei.com>
Signed-off-by: Shaohua Li <shli@fb.com>
If raid1d is handling a mix of read and write errors, handle_read_error's
call to freeze_array can get stuck.
This can happen because, though the bio_end_io_list is initially drained,
writes can be added to it via handle_write_finished as the retry_list
is processed. These writes contribute to nr_pending but are not included
in nr_queued.
If a later entry on the retry_list triggers a call to handle_read_error,
freeze array hangs waiting for nr_pending == nr_queued+extra. The writes
on the bio_end_io_list aren't included in nr_queued so the condition will
never be satisfied.
To prevent the hang, include bio_end_io_list writes in nr_queued.
There's probably a better way to handle decrementing nr_queued, but this
seemed like the safest way to avoid breaking surrounding code.
I'm happy to supply the script I used to repro this hang.
Fixes: 55ce74d4bfe1b(md/raid1: ensure device failure recorded before write request returns.)
Cc: stable@vger.kernel.org (v4.3+)
Signed-off-by: Nate Dailey <nate.dailey@stratus.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Since bitmap_start_sync will not return until
sync_blocks is not less than PAGE_SIZE>>9, so
the BUG_ON is not needed anymore.
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
It is not safe for an integrity profile to be changed while i/o is
in-flight in the queue. Prevent adding new disks or otherwise online
spares to an array if the device has an incompatible integrity profile.
The original change to the blk_integrity_unregister implementation in
md, commmit c7bfced9a6 "md: suspend i/o during runtime
blk_integrity_unregister" introduced an immediate hang regression.
This policy of disallowing changes the integrity profile once one has
been established is shared with DM.
Here is an abbreviated log from a test run that:
1/ Creates a degraded raid1 with an integrity-enabled device (pmem0s) [ 59.076127]
2/ Tries to add an integrity-disabled device (pmem1m) [ 90.489209]
3/ Retries with an integrity-enabled device (pmem1s) [ 205.671277]
[ 59.076127] md/raid1:md0: active with 1 out of 2 mirrors
[ 59.078302] md: data integrity enabled on md0
[..]
[ 90.489209] md0: incompatible integrity profile for pmem1m
[..]
[ 205.671277] md: super_written gets error=-5
[ 205.677386] md/raid1:md0: Disk failure on pmem1m, disabling device.
[ 205.677386] md/raid1:md0: Operation continuing on 1 devices.
[ 205.683037] RAID1 conf printout:
[ 205.684699] --- wd:1 rd:2
[ 205.685972] disk 0, wo:0, o:1, dev:pmem0s
[ 205.687562] disk 1, wo:1, o:1, dev:pmem1s
[ 205.691717] md: recovery of RAID array md0
Fixes: c7bfced9a6 ("md: suspend i/o during runtime blk_integrity_unregister")
Cc: <stable@vger.kernel.org>
Cc: Mike Snitzer <snitzer@redhat.com>
Reported-by: NeilBrown <neilb@suse.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Two major components to this update.
1/ the clustered-raid1 support from SUSE is nearly
complete. There are a few outstanding issues being
worked on. Maybe half a dozen patches will bring
this to a usable state.
2/ The first stage of journalled-raid5 support from
Facebook makes an appearance. With a journal
device configured (typically NVRAM or SSD), the
"RAID5 write hole" should be closed - a crash
during degraded operations cannot result in data
corruption.
The next stage will be to use the journal as a
write-behind cache so that latency can be reduced
and in some cases throughput increased by
performing more full-stripe writes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=TD5o
-----END PGP SIGNATURE-----
Merge tag 'md/4.4' of git://neil.brown.name/md
Pull md updates from Neil Brown:
"Two major components to this update.
1) The clustered-raid1 support from SUSE is nearly complete. There
are a few outstanding issues being worked on. Maybe half a dozen
patches will bring this to a usable state.
2) The first stage of journalled-raid5 support from Facebook makes an
appearance. With a journal device configured (typically NVRAM or
SSD), the "RAID5 write hole" should be closed - a crash during
degraded operations cannot result in data corruption.
The next stage will be to use the journal as a write-behind cache
so that latency can be reduced and in some cases throughput
increased by performing more full-stripe writes.
* tag 'md/4.4' of git://neil.brown.name/md: (66 commits)
MD: when RAID journal is missing/faulty, block RESTART_ARRAY_RW
MD: set journal disk ->raid_disk
MD: kick out journal disk if it's not fresh
raid5-cache: start raid5 readonly if journal is missing
MD: add new bit to indicate raid array with journal
raid5-cache: IO error handling
raid5: journal disk can't be removed
raid5-cache: add trim support for log
MD: fix info output for journal disk
raid5-cache: use bio chaining
raid5-cache: small log->seq cleanup
raid5-cache: new helper: r5_reserve_log_entry
raid5-cache: inline r5l_alloc_io_unit into r5l_new_meta
raid5-cache: take rdev->data_offset into account early on
raid5-cache: refactor bio allocation
raid5-cache: clean up r5l_get_meta
raid5-cache: simplify state machine when caches flushes are not needed
raid5-cache: factor out a helper to run all stripes for an I/O unit
raid5-cache: rename flushed_ios to finished_ios
raid5-cache: free I/O units earlier
...
Pull block integrity updates from Jens Axboe:
""This is the joint work of Dan and Martin, cleaning up and improving
the support for block data integrity"
* 'for-4.4/integrity' of git://git.kernel.dk/linux-block:
block, libnvdimm, nvme: provide a built-in blk_integrity nop profile
block: blk_flush_integrity() for bio-based drivers
block: move blk_integrity to request_queue
block: generic request_queue reference counting
nvme: suspend i/o during runtime blk_integrity_unregister
md: suspend i/o during runtime blk_integrity_unregister
md, dm, scsi, nvme, libnvdimm: drop blk_integrity_unregister() at shutdown
block: Inline blk_integrity in struct gendisk
block: Export integrity data interval size in sysfs
block: Reduce the size of struct blk_integrity
block: Consolidate static integrity profile properties
block: Move integrity kobject to struct gendisk
To incorporate --grow feature executed on one node, other nodes need to
acknowledge the change in number of disks. Call update_raid_disks()
to update internal data structures.
This leads to call check_reshape() -> md_allow_write() -> md_update_sb(),
this results in a deadlock. This is done so it can safely allocate memory
(which might trigger writeback which might write to raid1). This is
not required for md with a bitmap.
In the clustered case, we don't perform md_update_sb() in md_allow_write(),
but in do_md_run(). Also we disable safemode for clustered mode.
mddev->recovery_cp need not be set in check_sb_changes() because this
is required only when a node reads another node's bitmap. mddev->recovery_cp
(which is read from sb->resync_offset), is set only if mddev is in_sync.
Since we disabled safemode, in_sync is set to zero.
In a clustered environment, the MD may not be in sync because another
node could be writing to it. So make sure that in_sync is not set in
case of clustered node in __md_stop_writes().
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: NeilBrown <neilb@suse.com>
When a write fails and a bad-block-list is present, we can
update the bad-block-list instead of writing the data. If
this succeeds then it is OK clear the relevant bitmap-bit as
no further 'sync' of the block is needed.
However if writing the bad-block-list fails then we need to
treat the write as failed and particularly must not clear
the bitmap bit. Otherwise the device can be re-added (after
any hardware connection issues are resolved) and because the
relevant bit in the bitmap is clear, that block will not be
resynced. This leads to data corruption.
We already delay the final bio_endio() on the write until
the bad-block-list is written so that when the write
returns: either that data is safe, the bad-block record is
safe, or the fact that the device is faulty is safe.
However we *don't* delay the clearing of the bitmap, so the
bitmap bit can be recorded as cleared before we know if the
bad-block-list was written safely.
So: delay that until the write really is safe.
i.e. move the call to close_write() until just before
calling bio_endio(), and recheck the 'is array degraded'
status before making that call.
This bug goes back to v3.1 when bad-block-lists were
introduced, though it only affects arrays created with
mdadm-3.3 or later as only those have bad-block lists.
Backports will require at least
Commit: 55ce74d4bf ("md/raid1: ensure device failure recorded before write request returns.")
as well. I'll send that to 'stable' separately.
Note that of the two tests of R1BIO_WriteError that this
patch adds, the first is certain to fail and the second is
certain to succeed. However doing it this way makes the
patch more obviously correct. I will tidy the code up in a
future merge window.
Reported-and-tested-by: Nate Dailey <nate.dailey@stratus.com>
Cc: Jes Sorensen <Jes.Sorensen@redhat.com>
Fixes: cd5ff9a16f ("md/raid1: Handle write errors by updating badblock log.")
Signed-off-by: NeilBrown <neilb@suse.com>
Synchronize pending i/o against a change in the integrity profile to
avoid the possibility of spurious integrity errors. Given linear_add()
is suspending the mddev before manipulating the mddev, do the same for
the other personalities.
Acked-by: NeilBrown <neilb@suse.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This was introduced with 9e882242c6
which changed the return value of submit_bio_wait() to return != 0 on
error, but didn't update the caller accordingly.
Fixes: 9e882242c6 ("block: Add submit_bio_wait(), remove from md")
Cc: stable@vger.kernel.org (v3.10)
Reported-by: Bill Kuzeja <William.Kuzeja@stratus.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.com>
md-cluster: A better way for METADATA_UPDATED processing
The processing of METADATA_UPDATED message is too simple and prone to
errors. Besides, it would not update the internal data structures as
required.
This set of patches reads the superblock from one of the device of the MD
and checks for changes in the in-memory data structures. If there is a change,
it performs the necessary actions to keep the internal data structures
as it would be in the primary node.
An example is if a devices turns faulty. The algorithm is:
1. The initiator node marks the device as faulty and updates the superblock
2. The initiator node sends METADATA_UPDATED with an advisory device number to the rest of the nodes.
3. The receiving node on receiving the METADATA_UPDATED message
3.1 Reads the superblock
3.2 Detects a device has failed by comparing with memory structure
3.3 Calls the necessary functions to record the failure and get the device out of the active array.
3.4 Acknowledges the message.
The patch series also fixes adding the disk which was impacted because of
the changes.
Patches can also be found at
https://github.com/goldwynr/linux branch md-next
Changes since V2:
- Fix status synchrnoization after --add and --re-add operations
- Included Guoqing's patches on endian correctness, zeroing cmsg etc
- Restructure add_new_disk() and cancel()
Resync or recovery must be performed by only one node at a time.
A DLM lock resource, resync_lockres provides the mutual exclusion
so that only one node performs the recovery/resync at a time.
If a node is unable to get the resync_lockres, because recovery is
being performed by another node, it set MD_RECOVER_NEEDED so as
to schedule recovery in the future.
Remove the debug message in resync_info_update()
used during development.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
md_reload_sb is too simplistic and it explicitly needs to determine
the changes made by the writing node. However, there are multiple areas
where a simple reload could fail.
Instead, read the superblock of one of the "good" rdevs and update
the necessary information:
- read the superblock into a newly allocated page, by temporarily
swapping out rdev->sb_page and calling ->load_super.
- if that fails return
- if it succeeds, call check_sb_changes
1. iterates over list of active devices and checks the matching
dev_roles[] value.
If that is 'faulty', the device must be marked as faulty
- call md_error to mark the device as faulty. Make sure
not to set CHANGE_DEVS and wakeup mddev->thread or else
it would initiate a resync process, which is the responsibility
of the "primary" node.
- clear the Blocked bit
- Call remove_and_add_spares() to hot remove the device.
If the device is 'spare':
- call remove_and_add_spares() to get the number of spares
added in this operation.
- Reduce mddev->degraded to mark the array as not degraded.
2. reset recovery_cp
- read the rest of the rdevs to update recovery_offset. If recovery_offset
is equal to MaxSector, call spare_active() to set it In_sync
This required that recovery_offset be initialized to MaxSector, as
opposed to zero so as to communicate the end of sync for a rdev.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Suspending the entire device for resync could take too long. Resync
in small chunks.
cluster's resync window (32M) is maintained in r1conf as
cluster_sync_low and cluster_sync_high and processed in
raid1's sync_request(). If the current resync is outside the cluster
resync window:
1. Set the cluster_sync_low to curr_resync_completed.
2. Check if the sync will fit in the new window, if not issue a
wait_barrier() and set cluster_sync_low to sector_nr.
3. Set cluster_sync_high to cluster_sync_low + resync_window.
4. Send a message to all nodes so they may add it in their suspension
list.
bitmap_cond_end_sync is modified to allow to force a sync inorder
to get the curr_resync_completed uptodate with the sector passed.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The commit 55ce74d4bf (md/raid1: ensure
device failure recorded before write request returns) is causing crash in
the LVM2 testsuite test shell/lvchange-raid.sh. For me the crash is 100%
reproducible.
The reason for the crash is that the newly added code in raid1d moves the
list from conf->bio_end_io_list to tmp, then tests if tmp is non-empty and
then incorrectly pops the bio from conf->bio_end_io_list (which is empty
because the list was alrady moved).
Raid-10 has a similar bug.
Kernel Fault: Code=15 regs=000000006ccb8640 (Addr=0000000100000000)
CPU: 3 PID: 1930 Comm: mdX_raid1 Not tainted 4.2.0-rc5-bisect+ #35
task: 000000006cc1f258 ti: 000000006ccb8000 task.ti: 000000006ccb8000
YZrvWESTHLNXBCVMcbcbcbcbOGFRQPDI
PSW: 00001000000001001111111000001111 Not tainted
r00-03 000000ff0804fe0f 000000001059d000 000000001059f818 000000007f16be38
r04-07 000000001059d000 000000007f16be08 0000000000200200 0000000000000001
r08-11 000000006ccb8260 000000007b7934d0 0000000000000001 0000000000000000
r12-15 000000004056f320 0000000000000000 0000000000013dd0 0000000000000000
r16-19 00000000f0d00ae0 0000000000000000 0000000000000000 0000000000000001
r20-23 000000000800000f 0000000042200390 0000000000000000 0000000000000000
r24-27 0000000000000001 000000000800000f 000000007f16be08 000000001059d000
r28-31 0000000100000000 000000006ccb8560 000000006ccb8640 0000000000000000
sr00-03 0000000000249800 0000000000000000 0000000000000000 0000000000249800
sr04-07 0000000000000000 0000000000000000 0000000000000000 0000000000000000
IASQ: 0000000000000000 0000000000000000 IAOQ: 000000001059f61c 000000001059f620
IIR: 0f8010c6 ISR: 0000000000000000 IOR: 0000000100000000
CPU: 3 CR30: 000000006ccb8000 CR31: 0000000000000000
ORIG_R28: 000000001059d000
IAOQ[0]: call_bio_endio+0x34/0x1a8 [raid1]
IAOQ[1]: call_bio_endio+0x38/0x1a8 [raid1]
RP(r2): raid_end_bio_io+0x88/0x168 [raid1]
Backtrace:
[<000000001059f818>] raid_end_bio_io+0x88/0x168 [raid1]
[<00000000105a4f64>] raid1d+0x144/0x1640 [raid1]
[<000000004017fd5c>] kthread+0x144/0x160
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Fixes: 55ce74d4bf ("md/raid1: ensure device failure recorded before write request returns.")
Fixes: 95af587e95 ("md/raid10: ensure device failure recorded before write request returns.")
Signed-off-by: NeilBrown <neilb@suse.com>
close_sync() needs to set conf->next_resync to a large, but safe value
below MaxSector and use it to determine whether or not to set
start_next_window in wait_barrier()
Solution suggested by Neil Brown.
Reported-by: Nate Dailey <nate.dailey@stratus.com>
Tested-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Remove unneeded NULL test.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@ expression x; @@
-if (x != NULL)
\(kmem_cache_destroy\|mempool_destroy\|dma_pool_destroy\)(x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NeilBrown <neilb@suse.com>
Pull core block updates from Jens Axboe:
"This first core part of the block IO changes contains:
- Cleanup of the bio IO error signaling from Christoph. We used to
rely on the uptodate bit and passing around of an error, now we
store the error in the bio itself.
- Improvement of the above from myself, by shrinking the bio size
down again to fit in two cachelines on x86-64.
- Revert of the max_hw_sectors cap removal from a revision again,
from Jeff Moyer. This caused performance regressions in various
tests. Reinstate the limit, bump it to a more reasonable size
instead.
- Make /sys/block/<dev>/queue/discard_max_bytes writeable, by me.
Most devices have huge trim limits, which can cause nasty latencies
when deleting files. Enable the admin to configure the size down.
We will look into having a more sane default instead of UINT_MAX
sectors.
- Improvement of the SGP gaps logic from Keith Busch.
- Enable the block core to handle arbitrarily sized bios, which
enables a nice simplification of bio_add_page() (which is an IO hot
path). From Kent.
- Improvements to the partition io stats accounting, making it
faster. From Ming Lei.
- Also from Ming Lei, a basic fixup for overflow of the sysfs pending
file in blk-mq, as well as a fix for a blk-mq timeout race
condition.
- Ming Lin has been carrying Kents above mentioned patches forward
for a while, and testing them. Ming also did a few fixes around
that.
- Sasha Levin found and fixed a use-after-free problem introduced by
the bio->bi_error changes from Christoph.
- Small blk cgroup cleanup from Viresh Kumar"
* 'for-4.3/core' of git://git.kernel.dk/linux-block: (26 commits)
blk: Fix bio_io_vec index when checking bvec gaps
block: Replace SG_GAPS with new queue limits mask
block: bump BLK_DEF_MAX_SECTORS to 2560
Revert "block: remove artifical max_hw_sectors cap"
blk-mq: fix race between timeout and freeing request
blk-mq: fix buffer overflow when reading sysfs file of 'pending'
Documentation: update notes in biovecs about arbitrarily sized bios
block: remove bio_get_nr_vecs()
fs: use helper bio_add_page() instead of open coding on bi_io_vec
block: kill merge_bvec_fn() completely
md/raid5: get rid of bio_fits_rdev()
md/raid5: split bio for chunk_aligned_read
block: remove split code in blkdev_issue_{discard,write_same}
btrfs: remove bio splitting and merge_bvec_fn() calls
bcache: remove driver private bio splitting code
block: simplify bio_add_page()
block: make generic_make_request handle arbitrarily sized bios
blk-cgroup: Drop unlikely before IS_ERR(_OR_NULL)
block: don't access bio->bi_error after bio_put()
block: shrink struct bio down to 2 cache lines again
...
When a write to one of the legs of a RAID1 fails, the failure is
recorded in the metadata of the other leg(s) so that after a restart
the data on the failed drive wont be trusted even if that drive seems
to be working again (maybe a cable was unplugged).
Similarly when we record a bad-block in response to a write failure,
we must not let the write complete until the bad-block update is safe.
Currently there is no interlock between the write request completing
and the metadata update. So it is possible that the write will
complete, the app will confirm success in some way, and then the
machine will crash before the metadata update completes.
This is an extremely small hole for a racy to fit in, but it is
theoretically possible and so should be closed.
So:
- set MD_CHANGE_PENDING when requesting a metadata update for a
failed device, so we can know with certainty when it completes
- queue requests that experienced an error on a new queue which
is only processed after the metadata update completes
- call raid_end_bio_io() on bios in that queue when the time comes.
Signed-off-by: NeilBrown <neilb@suse.com>
When checking sync_action in a script, we want to be sure it is
as accurate as possible.
As resync/reshape etc doesn't always start immediately (a separate
thread is scheduled to do it), it is best if 'action_show'
checks if MD_RECOVER_NEEDED is set (which it does) and in that
case reports what is likely to start soon (which it only sometimes
does).
So:
- report 'reshape' if reshape_position suggests one might start.
- set MD_RECOVERY_RECOVER in raid1_reshape(), because that is very
likely to happen next.
Signed-off-by: NeilBrown <neilb@suse.com>
As generic_make_request() is now able to handle arbitrarily sized bios,
it's no longer necessary for each individual block driver to define its
own ->merge_bvec_fn() callback. Remove every invocation completely.
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Lars Ellenberg <drbd-dev@lists.linbit.com>
Cc: drbd-user@lists.linbit.com
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Yehuda Sadeh <yehuda@inktank.com>
Cc: Sage Weil <sage@inktank.com>
Cc: Alex Elder <elder@kernel.org>
Cc: ceph-devel@vger.kernel.org
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: dm-devel@redhat.com
Cc: Neil Brown <neilb@suse.de>
Cc: linux-raid@vger.kernel.org
Cc: Christoph Hellwig <hch@infradead.org>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Acked-by: NeilBrown <neilb@suse.de> (for the 'md' bits)
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Kent Overstreet <kent.overstreet@gmail.com>
[dpark: also remove ->merge_bvec_fn() in dm-thin as well as
dm-era-target, and resolve merge conflicts]
Signed-off-by: Dongsu Park <dpark@posteo.net>
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
raid1_end_read_request() assumes that the In_sync bits are consistent
with the ->degaded count.
raid1_spare_active updates the In_sync bit before the ->degraded count
and so exposes an inconsistency, as does error()
So extend the spinlock in raid1_spare_active() and error() to hide those
inconsistencies.
This should probably be part of
Commit: 34cab6f420 ("md/raid1: fix test for 'was read error from
last working device'.")
as it addresses the same issue. It fixes the same bug and should go
to -stable for same reasons.
Fixes: 76073054c9 ("md/raid1: clean up read_balance.")
Cc: stable@vger.kernel.org (v3.0+)
Signed-off-by: NeilBrown <neilb@suse.com>
Some places use helpers now, others don't. We only have the 'is set'
helper, add helpers for setting and clearing flags too.
It was a bit of a mess of atomic vs non-atomic access. With
BIO_UPTODATE gone, we don't have any risk of concurrent access to the
flags. So relax the restriction and don't make any of them atomic. The
flags that do have serialization issues (reffed and chained), we
already handle those separately.
Signed-off-by: Jens Axboe <axboe@fb.com>
Currently we have two different ways to signal an I/O error on a BIO:
(1) by clearing the BIO_UPTODATE flag
(2) by returning a Linux errno value to the bi_end_io callback
The first one has the drawback of only communicating a single possible
error (-EIO), and the second one has the drawback of not beeing persistent
when bios are queued up, and are not passed along from child to parent
bio in the ever more popular chaining scenario. Having both mechanisms
available has the additional drawback of utterly confusing driver authors
and introducing bugs where various I/O submitters only deal with one of
them, and the others have to add boilerplate code to deal with both kinds
of error returns.
So add a new bi_error field to store an errno value directly in struct
bio and remove the existing mechanisms to clean all this up.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
During a node failure, We need to suspend read balancing so that the
reads are directed to the first device and stale data is not read.
Suspending writes is not required because these would be recorded and
synced eventually.
A new flag MD_CLUSTER_SUSPEND_READ_BALANCING is set in recover_prep().
area_resyncing() will respond true for the entire devices if this
flag is set and the request type is READ. The flag is cleared
in recover_done().
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Reported-By: David Teigland <teigland@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.com>
When we get a read error from the last working device, we don't
try to repair it, and don't fail the device. We simple report a
read error to the caller.
However the current test for 'is this the last working device' is
wrong.
When there is only one fully working device, it assumes that a
non-faulty device is that device. However a spare which is rebuilding
would be non-faulty but so not the only working device.
So change the test from "!Faulty" to "In_sync". If ->degraded says
there is only one fully working device and this device is in_sync,
this must be the one.
This bug has existed since we allowed read_balance to read from
a recovering spare in v3.0
Reported-and-tested-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Fixes: 76073054c9 ("md/raid1: clean up read_balance.")
Cc: stable@vger.kernel.org (v3.0+)
Signed-off-by: NeilBrown <neilb@suse.com>
Currently, a bdi (backing_dev_info) embeds single wb (bdi_writeback)
and the role of the separation is unclear. For cgroup support for
writeback IOs, a bdi will be updated to host multiple wb's where each
wb serves writeback IOs of a different cgroup on the bdi. To achieve
that, a wb should carry all states necessary for servicing writeback
IOs for a cgroup independently.
This patch moves bdi->state into wb.
* enum bdi_state is renamed to wb_state and the prefix of all enums is
changed from BDI_ to WB_.
* Explicit zeroing of bdi->state is removed without adding zeoring of
wb->state as the whole data structure is zeroed on init anyway.
* As there's still only one bdi_writeback per backing_dev_info, all
uses of bdi->state are mechanically replaced with bdi->wb.state
introducing no behavior changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: drbd-dev@lists.linbit.com
Cc: Neil Brown <neilb@suse.de>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This option is not well justified and testing suggests that
it hardly ever makes any difference.
The comment suggests there might be a need to wait for non-resync
activity indicated by ->nr_waiting, however raise_barrier()
already waits for all of that.
So just remove it to simplify reasoning about speed limiting.
This allows us to remove a 'FIXME' comment from raid5.c as that
never used the flag.
Signed-off-by: NeilBrown <neilb@suse.de>
When a drive is marked write-mostly it should only be the
target of reads if there is no other option.
This behaviour was broken by
commit 9dedf60313
md/raid1: read balance chooses idlest disk for SSD
which causes a write-mostly device to be *preferred* is some cases.
Restore correct behaviour by checking and setting
best_dist_disk and best_pending_disk rather than best_disk.
We only need to test one of these as they are both changed
from -1 or >=0 at the same time.
As we leave min_pending and best_dist unchanged, any non-write-mostly
device will appear better than the write-mostly device.
Reported-by: Tomáš Hodek <tomas.hodek@volny.cz>
Reported-by: Dark Penguin <darkpenguin@yandex.ru>
Signed-off-by: NeilBrown <neilb@suse.de>
Link: http://marc.info/?l=linux-raid&m=135982797322422
Fixes: 9dedf60313
Cc: stable@vger.kernel.org (3.6+)
Algorithm:
1. Node 1 issues mdadm --manage /dev/mdX --add /dev/sdYY which issues
ioctl(ADD_NEW_DISC with disc.state set to MD_DISK_CLUSTER_ADD)
2. Node 1 sends NEWDISK with uuid and slot number
3. Other nodes issue kobject_uevent_env with uuid and slot number
(Steps 4,5 could be a udev rule)
4. In userspace, the node searches for the disk, perhaps
using blkid -t SUB_UUID=""
5. Other nodes issue either of the following depending on whether the disk
was found:
ioctl(ADD_NEW_DISK with disc.state set to MD_DISK_CANDIDATE and
disc.number set to slot number)
ioctl(CLUSTERED_DISK_NACK)
6. Other nodes drop lock on no-new-devs (CR) if device is found
7. Node 1 attempts EX lock on no-new-devs
8. If node 1 gets the lock, it sends METADATA_UPDATED after unmarking the disk
as SpareLocal
9. If not (get no-new-dev lock), it fails the operation and sends METADATA_UPDATED
10. Other nodes understand if the device is added or not by reading the superblock again after receiving the METADATA_UPDATED message.
Signed-off-by: Lidong Zhong <lzhong@suse.com>
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
set choose_first true for cluster read in read balance when the area
is resyncing.
Signed-off-by: Lidong Zhong <lzhong@suse.com>
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
If there is a resync going on, all nodes must suspend writes to the
range. This is recorded in the suspend_info/suspend_list.
If there is an I/O within the ranges of any of the suspend_info,
should_suspend will return 1.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
This modifies raid1's narrow_write_error to round up block_sectors to the
device's logical block size.
This prevents sd complaining about "Bad block number requested" for non-512-byte
sector disks.
Signed-off-by: Nate Dailey <nate.dailey@stratus.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Now that the ->stop function only frees the private data,
rename is accordingly.
Also pass in the private pointer as an arg rather than using
mddev->private. This flexibility will be useful in level_store().
Finally, don't clear ->private. It doesn't make sense to clear
it seeing that isn't what we free, and it is no longer necessary
to clear ->private (it was some time ago before ->to_remove was
introduced).
Setting ->to_remove in ->free() is a bit of a wart, but not a
big problem at the moment.
Signed-off-by: NeilBrown <neilb@suse.de>
Each md personality has a 'stop' operation which does two
things:
1/ it finalizes some aspects of the array to ensure nothing
is accessing the ->private data
2/ it frees the ->private data.
All the steps in '1' can apply to all arrays and so can be
performed in common code.
This is useful as in the case where we change the personality which
manages an array (in level_store()), it would be helpful to do
step 1 early, and step 2 later.
So split the 'step 1' functionality out into a new mddev_detach().
Signed-off-by: NeilBrown <neilb@suse.de>
There is no locking around calls to merge_bvec_fn(), so
it is possible that calls which coincide with a level (or personality)
change could go wrong.
So create a central dispatch point for these functions and use
rcu_read_lock().
If the array is suspended, reject any merge that can be rejected.
If not, we know it is safe to call the function.
Signed-off-by: NeilBrown <neilb@suse.de>
There is currently no locking around calls to the 'congested'
bdi function. If called at an awkward time while an array is
being converted from one level (or personality) to another, there
is a tiny chance of running code in an unreferenced module etc.
So add a 'congested' function to the md_personality operations
structure, and call it with appropriate locking from a central
'mddev_congested'.
When the array personality is changing the array will be 'suspended'
so no IO is processed.
If mddev_congested detects this, it simply reports that the
array is congested, which is a safe guess.
As mddev_suspend calls synchronize_rcu(), mddev_congested can
avoid races by included the whole call inside an rcu_read_lock()
region.
This require that the congested functions for all subordinate devices
can be run under rcu_lock. Fortunately this is the case.
Signed-off-by: NeilBrown <neilb@suse.de>
If a devices is being recovered it is not InSync and is not Faulty.
If a read error is experienced on that device, fix_read_error()
will be called, but it ignores non-InSync devices. So it will
neither fix the error nor fail the device.
It is incorrect that fix_read_error() ignores non-InSync devices.
It should only ignore Faulty devices. So fix it.
This became a bug when we allowed reading from a device that was being
recovered. It is suitable for any subsequent -stable kernel.
Fixes: da8840a747
Cc: stable@vger.kernel.org (v3.5+)
Reported-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Tested-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Both normal IO and resync IO can be retried with reschedule_retry()
and so be counted into ->nr_queued, but only normal IO gets counted in
->nr_pending.
Before the recent improvement to RAID1 resync there could only
possibly have been one or the other on the queue. When handling a
read failure it could only be normal IO. So when handle_read_error()
called freeze_array() the fact that freeze_array only compares
->nr_queued against ->nr_pending was safe.
But now that these two types can interleave, we can have both normal
and resync IO requests queued, so we need to count them both in
nr_pending.
This error can lead to freeze_array() hanging if there is a read
error, so it is suitable for -stable.
Fixes: 79ef3a8aa1
cc: stable@vger.kernel.org (v3.13+)
Reported-by: Brassow Jonathan <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
raise_barrier() uses next_resync as part of its calculations, so it
really should be updated first, instead of afterwards.
next_resync is always used under resync_lock so update it under
resync lock to, just before it is used. That is safest.
This could cause normal IO and resync IO to interact badly so
it suitable for -stable.
Fixes: 79ef3a8aa1
cc: stable@vger.kernel.org (v3.13+)
Signed-off-by: NeilBrown <neilb@suse.de>
next_resync is (approximately) the location for the next resync request.
However it does *not* reliably determine the earliest location
at which resync might be happening.
This is because resync requests can complete out of order, and
we only limit the number of current requests, not the distance
from the earliest pending request to the latest.
mddev->curr_resync_completed is a reliable indicator of the earliest
position at which resync could be happening. It is updated less
frequently, but is actually reliable which is more important.
So use it to determine if a write request is before the region
being resynced and so safe from conflict.
This error can allow resync IO to interfere with normal IO which
could lead to data corruption. Hence: stable.
Fixes: 79ef3a8aa1
cc: stable@vger.kernel.org (v3.13+)
Signed-off-by: NeilBrown <neilb@suse.de>
The resync/recovery process for raid1 was recently changed
so that writes could happen in parallel with resync providing
they were in different regions of the device.
There is a problem though: While a write request will always
wait for conflicting resync to complete, a resync request
will *not* always wait for conflicting writes to complete.
Two changes are needed to fix this:
1/ raise_barrier (which waits until it is safe to do resync)
must wait until current_window_requests is zero
2/ wait_battier (which waits at the start of a new write request)
must update current_window_requests if the request could
possible conflict with a concurrent resync.
As concurrent writes and resync can lead to data loss,
this patch is suitable for -stable.
Fixes: 79ef3a8aa1
Cc: stable@vger.kernel.org (v3.13+)
Cc: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
If there are outstanding writes when close_sync is called,
the change to ->start_next_window might cause them to
decrement the wrong counter when they complete. Fix this
by merging the two counters into the one that will be decremented.
Having an incorrect value in a counter can cause raise_barrier()
to hangs, so this is suitable for -stable.
Fixes: 79ef3a8aa1
cc: stable@vger.kernel.org (v3.13+)
Signed-off-by: NeilBrown <neilb@suse.de>
commit 79ef3a8aa1 made
it possible for reads to happen concurrently with resync.
This means that we need to be more careful where read_balancing
is allowed during resync - we can no longer be sure that any
resync that has already started will definitely finish.
So keep read_balancing to before recovery_cp, which is conservative
but safe.
This bug makes it possible to read from a device that doesn't
have up-to-date data, so it can cause data corruption.
So it is suitable for any kernel since 3.11.
Fixes: 79ef3a8aa1
cc: stable@vger.kernel.org (v3.13+)
Signed-off-by: NeilBrown <neilb@suse.de>
r1_bio->start_next_window is not initialised in the READ
case, so allow_barrier may incorrectly decrement
conf->current_window_requests
which can cause raise_barrier() to block forever.
Fixes: 79ef3a8aa1
cc: stable@vger.kernel.org (v3.13+)
Reported-by: Brassow Jonathan <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Currently we don't abort recovery on a write error if the write error
to the recovering device was triggerd by normal IO (as opposed to
recovery IO).
This means that for one bitmap region, the recovery might write to the
recovering device for a few sectors, then not bother for subsequent
sectors (as it never writes to failed devices). In this case
the bitmap bit will be cleared, but it really shouldn't.
The result is that if the recovering device fails and is then re-added
(after fixing whatever hardware problem triggerred the failure),
the second recovery won't redo the region it was in the middle of,
so some of the device will not be recovered properly.
If we abort the recovery, the region being processes will be cancelled
(bit not cleared) and the whole region will be retried.
As the bug can result in data corruption the patch is suitable for
-stable. For kernels prior to 3.11 there is a conflict in raid10.c
which will require care.
Original-from: jiao hui <jiaohui@bwstor.com.cn>
Reported-and-tested-by: jiao hui <jiaohui@bwstor.com.cn>
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@vger.kernel.org
When performing a user-request check/repair (MD_RECOVERY_REQUEST is set)
on a raid1, we allocate multiple bios each with their own set of pages.
If the page allocations for one bio fails, we currently do *not* free
the pages allocated for the previous bios, nor do we free the bio itself.
This patch frees all the already-allocate pages, and makes sure that
all the bios are freed as well.
This bug can cause a memory leak which can ultimately OOM a machine.
It was introduced in 3.10-rc1.
Fixes: a07876064a
Cc: Kent Overstreet <koverstreet@google.com>
Cc: stable@vger.kernel.org (3.10+)
Reported-by: Russell King - ARM Linux <linux@arm.linux.org.uk>
Signed-off-by: NeilBrown <neilb@suse.de>
commit 30bc9b5387
md/raid1: fix bio handling problems in process_checks()
Move the bio_reset() to a point before where BIO_UPTODATE is checked,
so that check now always report that the bio is uptodate, even if it is not.
This causes process_check() to sometimes treat read-errors as
successful matches so the good data isn't written out.
This patch preserves the flag until it is needed.
Bug was introduced in 3.11, but backported to 3.10-stable (as it fixed
an even worse bug). So suitable for any -stable since 3.10.
Reported-and-tested-by: Michael Tokarev <mjt@tls.msk.ru>
Cc: stable@vger.kernel.org (3.10+)
Fixed: 30bc9b5387
Signed-off-by: NeilBrown <neilb@suse.de>
Pull core block IO changes from Jens Axboe:
"The major piece in here is the immutable bio_ve series from Kent, the
rest is fairly minor. It was supposed to go in last round, but
various issues pushed it to this release instead. The pull request
contains:
- Various smaller blk-mq fixes from different folks. Nothing major
here, just minor fixes and cleanups.
- Fix for a memory leak in the error path in the block ioctl code
from Christian Engelmayer.
- Header export fix from CaiZhiyong.
- Finally the immutable biovec changes from Kent Overstreet. This
enables some nice future work on making arbitrarily sized bios
possible, and splitting more efficient. Related fixes to immutable
bio_vecs:
- dm-cache immutable fixup from Mike Snitzer.
- btrfs immutable fixup from Muthu Kumar.
- bio-integrity fix from Nic Bellinger, which is also going to stable"
* 'for-3.14/core' of git://git.kernel.dk/linux-block: (44 commits)
xtensa: fixup simdisk driver to work with immutable bio_vecs
block/blk-mq-cpu.c: use hotcpu_notifier()
blk-mq: for_each_* macro correctness
block: Fix memory leak in rw_copy_check_uvector() handling
bio-integrity: Fix bio_integrity_verify segment start bug
block: remove unrelated header files and export symbol
blk-mq: uses page->list incorrectly
blk-mq: use __smp_call_function_single directly
btrfs: fix missing increment of bi_remaining
Revert "block: Warn and free bio if bi_end_io is not set"
block: Warn and free bio if bi_end_io is not set
blk-mq: fix initializing request's start time
block: blk-mq: don't export blk_mq_free_queue()
block: blk-mq: make blk_sync_queue support mq
block: blk-mq: support draining mq queue
dm cache: increment bi_remaining when bi_end_io is restored
block: fixup for generic bio chaining
block: Really silence spurious compiler warnings
block: Silence spurious compiler warnings
block: Kill bio_pair_split()
...
The new iobarrier implementation in raid1 (which keeps normal writes
and resync activity separate) counts every request what is not before
the current resync point in either next_window_requests or
current_window_requests.
It flags that the request is counted by setting ->start_next_window.
allow_barrier follows this model exactly and decrements one of the
*_window_requests if and only if ->start_next_window is set.
However wait_barrier(), which increments *_window_requests uses a
slightly different test for setting -.start_next_window (which is set
from the return value of this function).
So there is a possibility of the counts getting out of sync, and this
leads to the resync hanging.
So change wait_barrier() to return a non-zero value in exactly the
same cases that it increments *_window_requests.
But was introduced in 3.13-rc1.
Reported-by: Bruno Wolff III <bruno@wolff.to>
URL: https://bugzilla.kernel.org/show_bug.cgi?id=68061
Fixes: 79ef3a8aa1
Cc: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Mostly optimisations and obscure bug fixes.
- raid5 gets less lock contention
- raid1 gets less contention between normal-io and resync-io
during resync.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=8RCg
-----END PGP SIGNATURE-----
Merge tag 'md/3.13' of git://neil.brown.name/md
Pull md update from Neil Brown:
"Mostly optimisations and obscure bug fixes.
- raid5 gets less lock contention
- raid1 gets less contention between normal-io and resync-io during
resync"
* tag 'md/3.13' of git://neil.brown.name/md:
md/raid5: Use conf->device_lock protect changing of multi-thread resources.
md/raid5: Before freeing old multi-thread worker, it should flush them.
md/raid5: For stripe with R5_ReadNoMerge, we replace REQ_FLUSH with REQ_NOMERGE.
UAPI: include <asm/byteorder.h> in linux/raid/md_p.h
raid1: Rewrite the implementation of iobarrier.
raid1: Add some macros to make code clearly.
raid1: Replace raise_barrier/lower_barrier with freeze_array/unfreeze_array when reconfiguring the array.
raid1: Add a field array_frozen to indicate whether raid in freeze state.
md: Convert use of typedef ctl_table to struct ctl_table
md/raid5: avoid deadlock when raid5 array has unack badblocks during md_stop_writes.
md: use MD_RECOVERY_INTR instead of kthread_should_stop in resync thread.
md: fix some places where mddev_lock return value is not checked.
raid5: Retry R5_ReadNoMerge flag when hit a read error.
raid5: relieve lock contention in get_active_stripe()
raid5: relieve lock contention in get_active_stripe()
wait: add wait_event_cmd()
md/raid5.c: add proper locking to error path of raid5_start_reshape.
md: fix calculation of stacking limits on level change.
raid5: Use slow_path to release stripe when mddev->thread is null
There is an iobarrier in raid1 because of contention between normal IO and
resync IO. It suspends all normal IO when resync/recovery happens.
However if normal IO is out side the resync window, there is no contention.
So this patch changes the barrier mechanism to only block IO that
could contend with the resync that is currently happening.
We partition the whole space into five parts.
|---------|-----------|------------|----------------|-------|
start next_resync start_next_window end_window
start + RESYNC_WINDOW = next_resync
next_resync + NEXT_NORMALIO_DISTANCE = start_next_window
start_next_window + NEXT_NORMALIO_DISTANCE = end_window
Firstly we introduce some concepts:
1 - RESYNC_WINDOW: For resync, there are 32 resync requests at most at the
same time. A sync request is RESYNC_BLOCK_SIZE(64*1024).
So the RESYNC_WINDOW is 32 * RESYNC_BLOCK_SIZE, that is 2MB.
2 - NEXT_NORMALIO_DISTANCE: the distance between next_resync
and start_next_window. It also indicates the distance between
start_next_window and end_window.
It is currently 3 * RESYNC_WINDOW_SIZE but could be tuned if
this turned out not to be optimal.
3 - next_resync: the next sector at which we will do sync IO.
4 - start: a position which is at most RESYNC_WINDOW before
next_resync.
5 - start_next_window: a position which is NEXT_NORMALIO_DISTANCE
beyond next_resync. Normal-io after this position doesn't need to
wait for resync-io to complete.
6 - end_window: a position which is 2 * NEXT_NORMALIO_DISTANCE beyond
next_resync. This also doesn't need to wait, but is counted
differently.
7 - current_window_requests: the count of normalIO between
start_next_window and end_window.
8 - next_window_requests: the count of normalIO after end_window.
NormalIO will be partitioned into four types:
NormIO1: the end sector of bio is smaller or equal the start
NormIO2: the start sector of bio larger or equal to end_window
NormIO3: the start sector of bio larger or equal to
start_next_window.
NormIO4: the location between start_next_window and end_window
|--------|-----------|--------------------|----------------|-------------|
| start | next_resync | start_next_window | end_window |
NormIO1 NormIO4 NormIO4 NormIO3 NormIO2
For NormIO1, we don't need any io barrier.
For NormIO4, we used a similar approach to the original iobarrier
mechanism. The normalIO and resyncIO must be kept separate.
For NormIO2/3, we add two fields to struct r1conf: "current_window_requests"
and "next_window_requests". They indicate the count of active
requests in the two window.
For these, we don't wait for resync io to complete.
For resync action, if there are NormIO4s, we must wait for it.
If not, we can proceed.
But if resync action reaches start_next_window and
current_window_requests > 0 (that is there are NormIO3s), we must
wait until the current_window_requests becomes zero.
When current_window_requests becomes zero, start_next_window also
moves forward. Then current_window_requests will replaced by
next_window_requests.
There is a problem which when and how to change from NormIO2 to
NormIO3. Only then can sync action progress.
We add a field in struct r1conf "start_next_window".
A: if start_next_window == MaxSector, it means there are no NormIO2/3.
So start_next_window = next_resync + NEXT_NORMALIO_DISTANCE
B: if current_window_requests == 0 && next_window_requests != 0, it
means start_next_window move to end_window
There is another problem which how to differentiate between
old NormIO2(now it is NormIO3) and NormIO2.
For example, there are many bios which are NormIO2 and a bio which is
NormIO3. NormIO3 firstly completed, so the bios of NormIO2 became NormIO3.
We add a field in struct r1bio "start_next_window".
This is used to record the position conf->start_next_window when the call
to wait_barrier() is made in make_request().
In allow_barrier(), we check the conf->start_next_window.
If r1bio->stat_next_window == conf->start_next_window, it means
there is no transition between NormIO2 and NormIO3.
If r1bio->start_next_window != conf->start_next_window, it mean
there was a transition between NormIO2 and NormIO3. There can only
have been one transition. So it only means the bio is old NormIO2.
For one bio, there may be many r1bio's. So we make sure
all the r1bio->start_next_window are the same value.
If we met blocked_dev in make_request(), it must call allow_barrier
and wait_barrier. So the former and the later value of
conf->start_next_window will be change.
If there are many r1bio's with differnet start_next_window,
for the relevant bio, it depend on the last value of r1bio.
It will cause error. To avoid this, we must wait for previous r1bios
to complete.
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
In a subsequent patch, we'll use some const parameters.
Using macros will make the code clearly.
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
We used to use raise_barrier to suspend normal IO while we reconfigure
the array. However raise_barrier will soon only suspend some normal
IO, not all. So we need something else.
Change it to use freeze_array.
But freeze_array not only suspends normal io, it also suspends
resync io.
For the place where call raise_barrier for reconfigure, it isn't a
problem.
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Because the following patch will rewrite the content between normal IO
and resync IO. So we used a parameter to indicate whether raid is in freeze
array.
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Someone cut and pasted md's md_trim_bio() into xen-blkfront.c. Come on,
we should know better than this.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Neil Brown <neilb@suse.de>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Since:
commit 7ceb17e87b
md: Allow devices to be re-added to a read-only array.
spares are activated on a read-only array. In case of raid1 and raid10
personalities it causes that not-in-sync devices are marked in-sync
without checking if recovery has been finished.
If a read-only array is degraded and one of its devices is not in-sync
(because the array has been only partially recovered) recovery will be skipped.
This patch adds checking if recovery has been finished before marking a device
in-sync for raid1 and raid10 personalities. In case of raid5 personality
such condition is already present (at raid5.c:6029).
Bug was introduced in 3.10 and causes data corruption.
Cc: stable@vger.kernel.org
Signed-off-by: Pawel Baldysiak <pawel.baldysiak@intel.com>
Signed-off-by: Lukasz Dorau <lukasz.dorau@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Recent change to use bio_copy_data() in raid1 when repairing
an array is faulty.
The underlying may have changed the bio in various ways using
bio_advance and these need to be undone not just for the 'sbio' which
is being copied to, but also the 'pbio' (primary) which is being
copied from.
So perform the reset on all bios that were read from and do it early.
This also ensure that the sbio->bi_io_vec[j].bv_len passed to
memcmp is correct.
This fixes a crash during a 'check' of a RAID1 array. The crash was
introduced in 3.10 so this is suitable for 3.10-stable.
Cc: stable@vger.kernel.org (3.10)
Reported-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: NeilBrown <neilb@suse.de>
DM RAID: Add ability to restore transiently failed devices on resume
This patch adds code to the resume function to check over the devices
in the RAID array. If any are found to be marked as failed and their
superblocks can be read, an attempt is made to reintegrate them into
the array. This allows the user to refresh the array with a simple
suspend and resume of the array - rather than having to load a
completely new table, allocate and initialize all the structures and
throw away the old instantiation.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Some tagged for -stable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=8iy3
-----END PGP SIGNATURE-----
Merge tag 'md-3.10-fixes' of git://neil.brown.name/md
Pull md bugfixes from Neil Brown:
"A few bugfixes for md
Some tagged for -stable"
* tag 'md-3.10-fixes' of git://neil.brown.name/md:
md/raid1,5,10: Disable WRITE SAME until a recovery strategy is in place
md/raid1,raid10: use freeze_array in place of raise_barrier in various places.
md/raid1: consider WRITE as successful only if at least one non-Faulty and non-rebuilding drive completed it.
md: md_stop_writes() should always freeze recovery.
There are cases where the kernel will believe that the WRITE SAME
command is supported by a block device which does not, in fact,
support WRITE SAME. This currently happens for SATA drivers behind a
SAS controller, but there are probably a hundred other ways that can
happen, including drive firmware bugs.
After receiving an error for WRITE SAME the block layer will retry the
request as a plain write of zeroes, but mdraid will consider the
failure as fatal and consider the drive failed. This has the effect
that all the mirrors containing a specific set of data are each
offlined in very rapid succession resulting in data loss.
However, just bouncing the request back up to the block layer isn't
ideal either, because the whole initial request-retry sequence should
be inside the write bitmap fence, which probably means that md needs
to do its own conversion of WRITE SAME to write zero.
Until the failure scenario has been sorted out, disable WRITE SAME for
raid1, raid5, and raid10.
[neilb: added raid5]
This patch is appropriate for any -stable since 3.7 when write_same
support was added.
Cc: stable@vger.kernel.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Various places in raid1 and raid10 are calling raise_barrier when they
really should call freeze_array.
The former is only intended to be called from "make_request".
The later has extra checks for 'nr_queued' and makes a call to
flush_pending_writes(), so it is safe to call it from within the
management thread.
Using raise_barrier will sometimes deadlock. Using freeze_array
should not.
As 'freeze_array' currently expects one request to be pending (in
handle_read_error - the only previous caller), we need to pass
it the number of pending requests (extra) to ignore.
The deadlock was made particularly noticeable by commits
050b66152f (raid10) and 6b740b8d79 (raid1) which
appeared in 3.4, so the fix is appropriate for any -stable
kernel since then.
This patch probably won't apply directly to some early kernels and
will need to be applied by hand.
Cc: stable@vger.kernel.org
Reported-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Without that fix, the following scenario could happen:
- RAID1 with drives A and B; drive B was freshly-added and is rebuilding
- Drive A fails
- WRITE request arrives to the array. It is failed by drive A, so
r1_bio is marked as R1BIO_WriteError, but the rebuilding drive B
succeeds in writing it, so the same r1_bio is marked as
R1BIO_Uptodate.
- r1_bio arrives to handle_write_finished, badblocks are disabled,
md_error()->error() does nothing because we don't fail the last drive
of raid1
- raid_end_bio_io() calls call_bio_endio()
- As a result, in call_bio_endio():
if (!test_bit(R1BIO_Uptodate, &r1_bio->state))
clear_bit(BIO_UPTODATE, &bio->bi_flags);
this code doesn't clear the BIO_UPTODATE flag, and the whole master
WRITE succeeds, back to the upper layer.
So we returned success to the upper layer, even though we had written
the data onto the rebuilding drive only. But when we want to read the
data back, we would not read from the rebuilding drive, so this data
is lost.
[neilb - applied identical change to raid10 as well]
This bug can result in lost data, so it is suitable for any
-stable kernel.
Cc: stable@vger.kernel.org
Signed-off-by: Alex Lyakas <alex@zadarastorage.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Pull block core updates from Jens Axboe:
- Major bit is Kents prep work for immutable bio vecs.
- Stable candidate fix for a scheduling-while-atomic in the queue
bypass operation.
- Fix for the hang on exceeded rq->datalen 32-bit unsigned when merging
discard bios.
- Tejuns changes to convert the writeback thread pool to the generic
workqueue mechanism.
- Runtime PM framework, SCSI patches exists on top of these in James'
tree.
- A few random fixes.
* 'for-3.10/core' of git://git.kernel.dk/linux-block: (40 commits)
relay: move remove_buf_file inside relay_close_buf
partitions/efi.c: replace useless kzalloc's by kmalloc's
fs/block_dev.c: fix iov_shorten() criteria in blkdev_aio_read()
block: fix max discard sectors limit
blkcg: fix "scheduling while atomic" in blk_queue_bypass_start
Documentation: cfq-iosched: update documentation help for cfq tunables
writeback: expose the bdi_wq workqueue
writeback: replace custom worker pool implementation with unbound workqueue
writeback: remove unused bdi_pending_list
aoe: Fix unitialized var usage
bio-integrity: Add explicit field for owner of bip_buf
block: Add an explicit bio flag for bios that own their bvec
block: Add bio_alloc_pages()
block: Convert some code to bio_for_each_segment_all()
block: Add bio_for_each_segment_all()
bounce: Refactor __blk_queue_bounce to not use bi_io_vec
raid1: use bio_copy_data()
pktcdvd: Use bio_reset() in disabled code to kill bi_idx usage
pktcdvd: use bio_copy_data()
block: Add bio_copy_data()
...
In SSD/hard disk hybid storage, discard request should be ignored for hard
disk. We used to be doing this way, but the unplug path forgets it.
This is suitable for stable tree since v3.6.
Cc: stable@vger.kernel.org
Reported-and-tested-by: Markus <M4rkusXXL@web.de>
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Hi.
Raid1 and raid10 devices leak memory every time they stop.
This is a patch for linux-3.9.0-rc7 to fix this problem.
Thanks,
Hirokazu Takahashi.
Signed-off-by: Hirokazu Takahashi <taka@valinux.co.jp>
Signed-off-by: NeilBrown <neilb@suse.de>
More prep work for immutable bvecs:
A few places in the code were either open coding or using the wrong
version - fix.
After we introduce the bvec iter, it'll no longer be possible to modify
the biovec through bio_for_each_segment_all() - it doesn't increment a
pointer to the current bvec, you pass in a struct bio_vec (not a
pointer) which is updated with what the current biovec would be (taking
into account bi_bvec_done and bi_size).
So because of that it's more worthwhile to be consistent about
bio_for_each_segment()/bio_for_each_segment_all() usage.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: NeilBrown <neilb@suse.de>
CC: Alasdair Kergon <agk@redhat.com>
CC: dm-devel@redhat.com
CC: Alexander Viro <viro@zeniv.linux.org.uk>
__bio_for_each_segment() iterates bvecs from the specified index
instead of bio->bv_idx. Currently, the only usage is to walk all the
bvecs after the bio has been advanced by specifying 0 index.
For immutable bvecs, we need to split these apart;
bio_for_each_segment() is going to have a different implementation.
This will also help document the intent of code that's using it -
bio_for_each_segment_all() is only legal to use for code that owns the
bio.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: Neil Brown <neilb@suse.de>
CC: Boaz Harrosh <bharrosh@panasas.com>
This doesn't really delete any code _yet_, but once immutable bvecs are
done we can just delete the rest of the code in that loop.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: NeilBrown <neilb@suse.de>
More bi_idx removal. This code was just open coding bio_clone(). This
could probably be further improved by using bio_advance() instead of
skipping over null pages, but that'd be a larger rework.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: NeilBrown <neilb@suse.de>
Random cleanup - this code was duplicated and it's not really specific
to md.
Also added the ability to return the actual error code.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: NeilBrown <neilb@suse.de>
Acked-by: Tejun Heo <tj@kernel.org>
Bunch of places in the code weren't using it where they could be -
this'll reduce the size of the patch that puts bi_sector/bi_size/bi_idx
into a struct bvec_iter.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: "Ed L. Cashin" <ecashin@coraid.com>
CC: Nick Piggin <npiggin@kernel.dk>
CC: Jiri Kosina <jkosina@suse.cz>
CC: Jim Paris <jim@jtan.com>
CC: Geoff Levand <geoff@infradead.org>
CC: Alasdair Kergon <agk@redhat.com>
CC: dm-devel@redhat.com
CC: Neil Brown <neilb@suse.de>
CC: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Ed Cashin <ecashin@coraid.com>
Just a little convenience macro - main reason to add it now is preparing
for immutable bio vecs, it'll reduce the size of the patch that puts
bi_sector/bi_size/bi_idx into a struct bvec_iter.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: Lars Ellenberg <drbd-dev@lists.linbit.com>
CC: Jiri Kosina <jkosina@suse.cz>
CC: Alasdair Kergon <agk@redhat.com>
CC: dm-devel@redhat.com
CC: Neil Brown <neilb@suse.de>
CC: Martin Schwidefsky <schwidefsky@de.ibm.com>
CC: Heiko Carstens <heiko.carstens@de.ibm.com>
CC: linux-s390@vger.kernel.org
CC: Chris Mason <chris.mason@fusionio.com>
CC: Steven Whitehouse <swhiteho@redhat.com>
Acked-by: Steven Whitehouse <swhiteho@redhat.com>
When raid1/raid10 needs to fix a read error, it first drains
all pending requests by calling freeze_array().
This calls flush_pending_writes() if it needs to sleep,
but some writes may be pending in a per-process plug rather
than in the per-array request queue.
When raid1{,0}_unplug() moves the request from the per-process
plug to the per-array request queue (from which
flush_pending_writes() can flush them), it needs to wake up
freeze_array(), or freeze_array() will never flush them and so
it will block forever.
So add the requires wake_up() calls.
This bug was introduced by commit
f54a9d0e59
for raid1 and a similar commit for RAID10, and so has been present
since linux-3.6. As the bug causes a deadlock I believe this fix is
suitable for -stable.
Cc: stable@vger.kernel.org (3.6.y 3.7.y 3.8.y)
Reported-by: Tregaron Bayly <tbayly@bluehost.com>
Tested-by: Tregaron Bayly <tbayly@bluehost.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Set mddev queue's max_write_same_sectors to its chunk_sector value (before
disk_stack_limits merges the underlying disk limits.) With that in place,
be sure to handle writes coming down from the block layer that have the
REQ_WRITE_SAME flag set. That flag needs to be copied into any newly cloned
write bio.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Pull block driver update from Jens Axboe:
"Now that the core bits are in, here are the driver bits for 3.8. The
branch contains:
- A huge pile of drbd bits that were dumped from the 3.7 merge
window. Following that, it was both made perfectly clear that
there is going to be no more over-the-wall pulls and how the
situation on individual pulls can be improved.
- A few cleanups from Akinobu Mita for drbd and cciss.
- Queue improvement for loop from Lukas. This grew into adding a
generic interface for waiting/checking an even with a specific
lock, allowing this to be pulled out of md and now loop and drbd is
also using it.
- A few fixes for xen back/front block driver from Roger Pau Monne.
- Partition improvements from Stephen Warren, allowing partiion UUID
to be used as an identifier."
* 'for-3.8/drivers' of git://git.kernel.dk/linux-block: (609 commits)
drbd: update Kconfig to match current dependencies
drbd: Fix drbdsetup wait-connect, wait-sync etc... commands
drbd: close race between drbd_set_role and drbd_connect
drbd: respect no-md-barriers setting also when changed online via disk-options
drbd: Remove obsolete check
drbd: fixup after wait_even_lock_irq() addition to generic code
loop: Limit the number of requests in the bio list
wait: add wait_event_lock_irq() interface
xen-blkfront: free allocated page
xen-blkback: move free persistent grants code
block: partition: msdos: provide UUIDs for partitions
init: reduce PARTUUID min length to 1 from 36
block: store partition_meta_info.uuid as a string
cciss: use check_signature()
cciss: cleanup bitops usage
drbd: use copy_highpage
drbd: if the replication link breaks during handshake, keep retrying
drbd: check return of kmalloc in receive_uuids
drbd: Broadcast sync progress no more often than once per second
drbd: don't try to clear bits once the disk has failed
...
New wait_event{_interruptible}_lock_irq{_cmd} macros added. This commit
moves the private wait_event_lock_irq() macro from MD to regular wait
includes, introduces new macro wait_event_lock_irq_cmd() instead of using
the old method with omitting cmd parameter which is ugly and makes a use
of new macros in the MD. It also introduces the _interruptible_ variant.
The use of new interface is when one have a special lock to protect data
structures used in the condition, or one also needs to invoke "cmd"
before putting it to sleep.
All new macros are expected to be called with the lock taken. The lock
is released before sleep and is reacquired afterwards. We will leave the
macro with the lock held.
Note to DM: IMO this should also fix theoretical race on waitqueue while
using simultaneously wait_event_lock_irq() and wait_event() because of
lack of locking around current state setting and wait queue removal.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Cc: Neil Brown <neilb@suse.de>
Cc: David Howells <dhowells@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If the raid1 or raid10 unplug function gets called
from a make_request function (which is very possible) when
there are bios on the current->bio_list list, then it will not
be able to successfully call bitmap_unplug() and it could
need to submit more bios and wait for them to complete.
But they won't complete while current->bio_list is non-empty.
So detect that case and handle the unplugging off to another thread
just like we already do when called from within the scheduler.
RAID1 version of bug was introduced in 3.6, so that part of fix is
suitable for 3.6.y. RAID10 part won't apply.
Cc: stable@vger.kernel.org
Reported-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Reported-by: Peter Maloney <peter.maloney@brockmann-consult.de>
Signed-off-by: NeilBrown <neilb@suse.de>
setup_conf in raid1.c uses conf->raid_disks before assigning
a value. It is used when including 'Replacement' devices.
The consequence is that assembling an array which contains a
replacement will misbehave and either not include the replacement, or
not include the device being replaced.
Though this doesn't lead directly to data corruption, it could lead to
reduced data safety.
So use mddev->raid_disks, which is initialised, instead.
Bug was introduced by commit c19d57980b
md/raid1: recognise replacements when assembling arrays.
in 3.3, so fix is suitable for 3.3.y thru 3.6.y.
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
Now that multiple threads can handle stripes, it is safer to
use an atomic64_t for resync_mismatches, to avoid update races.
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When we get a read error, we arrange for raid1d to handle it.
Currently we release the reference on the device. This can result
in
conf->mirrors[read_disk].rdev
being NULL in fix_read_error, if the device happens to get removed
before the read error is handled.
So instead keep the reference until the read error has been fully
handled.
Reported-by: hank <pyu@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Change the thread parameter, so the thread can carry extra info. Next patch
will use it.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
This makes md raid 1 support TRIM.
If one disk supports discard and another not, or one has discard_zero_data and
another not, there could be inconsistent between data from such disks. But this
should not matter, discarded data is useless. This will add extra copy in rebuild
though.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
This contains a few patches that depend on
plugging changes in the block layer so needs to wait
for those.
It also contains a Kconfig fix for the new RAID10 support
in dm-raid.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=ovN2
-----END PGP SIGNATURE-----
Merge tag 'md-3.6' of git://neil.brown.name/md
Pull additional md update from NeilBrown:
"This contains a few patches that depend on plugging changes in the
block layer so needed to wait for those.
It also contains a Kconfig fix for the new RAID10 support in dm-raid."
* tag 'md-3.6' of git://neil.brown.name/md:
md/dm-raid: DM_RAID should select MD_RAID10
md/raid1: submit IO from originating thread instead of md thread.
raid5: raid5d handle stripe in batch way
raid5: make_request use batch stripe release
queuing writes to the md thread means that all requests go through the
one processor which may not be able to keep up with very high request
rates.
So use the plugging infrastructure to submit all requests on unplug.
If a 'schedule' is needed, we fall back on the old approach of handing
the requests to the thread for it to handle.
Signed-off-by: NeilBrown <neilb@suse.de>
Pull block driver changes from Jens Axboe:
- Making the plugging support for drivers a bit more sane from Neil.
This supersedes the plugging change from Shaohua as well.
- The usual round of drbd updates.
- Using a tail add instead of a head add in the request completion for
ndb, making us find the most completed request more quickly.
- A few floppy changes, getting rid of a duplicated flag and also
running the floppy init async (since it takes forever in boot terms)
from Andi.
* 'for-3.6/drivers' of git://git.kernel.dk/linux-block:
floppy: remove duplicated flag FD_RAW_NEED_DISK
blk: pass from_schedule to non-request unplug functions.
block: stack unplug
blk: centralize non-request unplug handling.
md: remove plug_cnt feature of plugging.
block/nbd: micro-optimization in nbd request completion
drbd: announce FLUSH/FUA capability to upper layers
drbd: fix max_bio_size to be unsigned
drbd: flush drbd work queue before invalidate/invalidate remote
drbd: fix potential access after free
drbd: call local-io-error handler early
drbd: do not reset rs_pending_cnt too early
drbd: reset congestion information before reporting it in /proc/drbd
drbd: report congestion if we are waiting for some userland callback
drbd: differentiate between normal and forced detach
drbd: cleanup, remove two unused global flags
floppy: Run floppy initialization asynchronous
This seemed like a good idea at the time, but after further thought I
cannot see it making a difference other than very occasionally and
testing to try to exercise the case it is most likely to help did not
show any performance difference by removing it.
So remove the counting of active plugs and allow 'pending writes' to
be activated at any time, not just when no plugs are active.
This is only relevant when there is a write-intent bitmap, and the
updating of the bitmap will likely introduce enough delay that
the single-threading of bitmap updates will be enough to collect large
numbers of updates together.
Removing this will make it easier to centralise the unplug code, and
will clear the other for other unplug enhancements which have a
measurable effect.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When doing resync or repair, attempt to correct bad blocks, according
to WriteErrorSeen policy
Signed-off-by: Alex Lyakas <alex.bolshoy@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
If a resync of a RAID1 array with 2 devices finds a known bad block
one device it will neither read from, or write to, that device for
this block offset.
So there will be one read_target (The other device) and zero write
targets.
This condition causes md/raid1 to abort the resync assuming that it
has finished - without known bad blocks this would be true.
When there are no write targets because of the presence of bad blocks
we should only skip over the area covered by the bad block.
RAID10 already gets this right, raid1 doesn't. Or didn't.
As this can cause a 'sync' to abort early and appear to have succeeded
it could lead to some data corruption, so it suitable for -stable.
Cc: stable@vger.kernel.org
Reported-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
For SSD, if request size exceeds specific value (optimal io size), request size
isn't important for bandwidth. In such condition, if making request size bigger
will cause some disks idle, the total throughput will actually drop. A good
example is doing a readahead in a two-disk raid1 setup.
So when should we split big requests? We absolutly don't want to split big
request to very small requests. Even in SSD, big request transfer is more
efficient. This patch only considers request with size above optimal io size.
If all disks are busy, is it worth doing a split? Say optimal io size is 16k,
two requests 32k and two disks. We can let each disk run one 32k request, or
split the requests to 4 16k requests and each disk runs two. It's hard to say
which case is better, depending on hardware.
So only consider case where there are idle disks. For readahead, split is
always better in this case. And in my test, below patch can improve > 30%
thoughput. Hmm, not 100%, because disk isn't 100% busy.
Such case can happen not just in readahead, for example, in directio. But I
suppose directio usually will have bigger IO depth and make all disks busy, so
I ignored it.
Note: if the raid uses any hard disk, we don't prevent merging. That will make
performace worse.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
SSD hasn't spindle, distance between requests means nothing. And the original
distance based algorithm sometimes can cause severe performance issue for SSD
raid.
Considering two thread groups, one accesses file A, the other access file B.
The first group will access one disk and the second will access the other disk,
because requests are near from one group and far between groups. In this case,
read balance might keep one disk very busy but the other relative idle. For
SSD, we should try best to distribute requests to as many disks as possible.
There isn't spindle move penality anyway.
With below patch, I can see more than 50% throughput improvement sometimes
depending on workloads.
The only exception is small requests can be merged to a big request which
typically can drive higher throughput for SSD too. Such small requests are
sequential reads. Unlike hard disk, sequential read which can't be merged (for
example direct IO, or read without readahead) can be ignored for SSD. Again
there is no spindle move penality. readahead dispatches small requests and such
requests can be merged.
Last patch can help detect sequential read well, at least if concurrent read
number isn't greater than raid disk number. In that case, distance based
algorithm doesn't work well too.
V2: For hard disk and SSD mixed raid, doesn't use distance based algorithm for
random IO too. This makes the algorithm generic for raid with SSD.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Currently the sequential read detection is global wide. It's natural to make it
per disk based, which can improve the detection for concurrent multiple
sequential reads. And next patch will make SSD read balance not use distance
based algorithm, where this change help detect truly sequential read for SSD.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
MD RAID1/RAID10: Move some macros from .h file to .c file
There are three macros (IO_BLOCKED,IO_MADE_GOOD,BIO_SPECIAL) which are defined
in both raid1.h and raid10.h. They are only used in there respective .c files.
However, if we wish to make RAID10 accessible to the device-mapper RAID
target (dm-raid.c), then we need to move these macros into the .c files where
they are used so that they do not conflict with each other.
The macros from the two files are identical and could be moved into md.h, but
I chose to leave the duplication and have them remain in the personality
files.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
MD RAID1: Rename the structure 'mirror_info' to 'raid1_info'
The same structure name ('mirror_info') is used by raid10. Each of these
structures are defined in there respective header files. If dm-raid is
to support both RAID1 and RAID10, the header files will be included and
the structure names must not collide. While only one of these structure
names needs to change, this patch adds consistency to the naming of the
structure.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
commit 4367af5561
md/raid1: clear bad-block record when write succeeds.
Added a 'reschedule_retry' call possibility at the end of
end_sync_write, but didn't add matching code at the end of
sync_request_write. So if the writes complete very quickly, or
scheduling makes it seem that way, then we can miss rescheduling
the request and the resync could hang.
Also commit 73d5c38a95
md: avoid races when stopping resync.
Fix a race condition in this same code in end_sync_write but didn't
make the change in sync_request_write.
This patch updates sync_request_write to fix both of those.
Patch is suitable for 3.1 and later kernels.
Reported-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Original-version-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
This bug has been present ever since data-check was introduce
in 2.6.16. However it would only fire if a data-check were
done on a degraded array, which was only possible if the array
has 3 or more devices. This is certainly possible, but is quite
uncommon.
Since hot-replace was added in 3.3 it can happen more often as
the same condition can arise if not all possible replacements are
present.
The problem is that as soon as we submit the last read request, the
'r1_bio' structure could be freed at any time, so we really should
stop looking at it. If the last device is being read from we will
stop looking at it. However if the last device is not due to be read
from, we will still check the bio pointer in the r1_bio, but the
r1_bio might already be free.
So use the read_targets counter to make sure we stop looking for bios
to submit as soon as we have submitted them all.
This fix is suitable for any -stable kernel since 2.6.16.
Cc: stable@vger.kernel.org
Reported-by: Arnold Schulz <arnysch@gmx.net>
Signed-off-by: NeilBrown <neilb@suse.de>
The value returned by "mddev_check_plug" is only valid until the
next 'schedule' as that will unplug things. This could happen at any
call to mempool_alloc.
So just calling mddev_check_plug at the start doesn't really make
sense.
So call it just before, or just after, queuing things for the thread.
As the action that happens at unplug is to wake the thread, this makes
lots of sense.
If we cannot add a plug (which requires a small GFP_ATOMIC alloc) we
wake thread immediately.
RAID5 is a bit different. Requests are queued for the thread and the
thread is woken by release_stripe. So we don't need to wake the
thread on failure.
However the thread doesn't perform certain actions when there is any
active plug, so it is important to install a plug before waking the
thread. So for RAID5 we install the plug *before* queuing the request
and waking the thread.
Without this patch it is possible for raid1 or raid10 to queue a
request without then waking the thread, resulting in the array locking
up.
Also change raid10 to only flush_pending_write when there are not
active plugs, just like raid1.
This patch is suitable for 3.0 or later. I plan to submit it to
-stable, but I'll like to let it spend a few weeks in mainline
first to be sure it is completely safe.
Signed-off-by: NeilBrown <neilb@suse.de>
When we added hot_replace we doubled the number of devices
that could be in a RAID1 array. So we doubled how far read_balance
would search. Unfortunately we didn't double the point at which
it looped back to the beginning - so it effectively loops over
all non-replacement disks twice.
This doesn't cause bad behaviour, but it pointless and means we
never read from replacement devices.
Signed-off-by: NeilBrown <neilb@suse.de>
Having the 'name' arg optional and defaulting to the current
personality name is no necessary and leads to errors, as when
changing the level of an array we can end up using the
name of the old level instead of the new one.
So make it non-optional and always explicitly pass the name
of the level that the array will be.
Reported-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The new merge_bvec_fn which calls the corresponding function
in subsidiary devices requires that mddev->merge_check_needed
be set if any child has a merge_bvec_fn.
However were were only setting that when a device was hot-added,
not when a device was present from the start.
This bug was introduced in 3.4 so patch is suitable for 3.4.y
kernels. However that are conflicts in raid10.c so a separate
patch will be needed for 3.4.y.
Cc: stable@vger.kernel.org
Reported-by: Sebastian Riemer <sebastian.riemer@profitbricks.com>
Signed-off-by: NeilBrown <neilb@suse.de>
A RAID1 device does not necessarily need a fullsync if the bitmap can be used instead.
Similar to commit d6b212f4b1 in raid5.c, if a raid1
device can be brought back (i.e. from a transient failure) it shouldn't need a
complete resync. Provided the bitmap is not to old, it will have recorded the areas
of the disk that need recovery.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Now that bitmaps can be resized, we can allow an array to be resized
while the bitmap is present.
This only covers resizing that involves changing the effective size
of member devices, not resizing that changes the number of devices.
Signed-off-by: NeilBrown <neilb@suse.de>
When attempting to fix a read error, it is acceptable to read from a
device that is recovering, provided the recovery has got past the
place we are reading from. This makes the test for "can we read from
here" the same as the test in read_balance.
Signed-off-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When reshaping we can avoid costly intermediate backup by
changing the 'start' address of the array on the device
(if there is enough room).
So as a first step, allow such a change to be requested
through sysfs, and recorded in v1.x metadata.
(As we didn't previous check that all 'pad' fields were zero,
we need a new FEATURE flag for this.
A (belatedly) check that all remaining 'pad' fields are
zero to avoid a repeat of this)
The new data offset must be requested separately for each device.
This allows each to have a different change in the data offset.
This is not likely to be used often but as data_offset can be
set per-device, new_data_offset should be too.
This patch also removes the 'acknowledged' arg to rdev_set_badblocks as
it is never used and never will be. At the same time we add a new
arg ('in_new') which is currently always zero but will be used more
soon.
When a reshape finishes we will need to update the data_offset
and rdev->sectors. So provide an exported function to do that.
Signed-off-by: NeilBrown <neilb@suse.de>
If r1bio->sectors % 8 != 0,then the memcmp and a later
memcpy will omit the last bio_vec.
This is suitable for any stable kernel since 3.1 when bad-block
management was introduced.
Cc: stable@vger.kernel.org
Signed-off-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
colyli@suse.de