To get a better idea if underruns occurred during crtc disabling,
let's check for them explicitly. This helps in cases where the
error interrupt isn't active, or there is no underrun interrupt
support at all.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448050160-14124-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We sometimes get a spurious CPU pipe underrun somewhere between
enabling port A and enabling vdd for the panel. Observed on both
ILK and IVB with port A eDP. Suppress FIFO underrun reporting
around the port and vdd enable to avoid the dmesg errors.
Not sure if port D eDP would suffer from the same issue, but assume
that it doesn't until proven differently.
Testcase: igt/kms_setmode
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448050160-14124-2-git-send-email-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
We still get spurious pipe underruns on ILK/SNB/IVB under two
circumstances when dealing with PCH ports:
* When the pipe has been disabled, but FDI RX/TX is still enabled
* During FDI link training
Both cases seem to happen at least when we do VGA+HDMI cloning
from the same pipe. I don't think I've seen them when not cloning,
but can't be 100% sure.
Disable underrun reporting around those places to eliminate the
dmesg errors.
Testcase: igt/kms_setmode/basic-clone-single-crtc
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448050160-14124-1-git-send-email-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
It is not a bad idea to disable the PSR feature on Sink
when we are disabling on the Source.
v2: Move dpcd write inside mutex protected area as suggested by Sonika.
Cc: Sonika Jindal <sonika.jindal@intel.com>
Suggested-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Whenever DMC firmware put the HW into DC State a bunch
of registers including this perf counter is reset to 0.
Even with PSR active and working we could still read
"Performance_Counter: 0" what will misslead people to believe
PSR is broken. For instance on SKL we can only see PC10
residency with screen on if PSR is working properly.
However Performance_Counter was showing 0.
Even if it restored properly on DC6 exit we don't want to
give users the wrong impression that PSR is not working
while we know for sure it is.
So, it is better to remove this counter information while
we don't have a better way to track PSR residency.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we introduced PSR we let LPSP masked allowing us to get PSR
independently from the audio runtime PM. However in one of the
attempts to get PSR enabled by default one user reported one specific
case where he would miss screen updates if scrolling the firefox in a
Gnome environment when i915 runtime pm was enabled. So for
this specific case that (I could never create an i-g-t test case)
we decided to remove the LPSP mask and let HW tracking taking care of
this case. The mask got removed later by my
commit 09108b90f0 ("drm/i915: PSR: Remove Low Power HW tracking mask.")
So we started depending on audio driver again, what is bad.
With previous commit
"drm/i915: PSR: Let's rely more on frontbuffer tracking."
we transfered the PSR exit responsability totally to SW frontbuffer
tracking. So now can safelly shut off a bit the HW tracking, or
at least this case that makes us to depend on other drivers.
v2: Update commit message since this patch by itself doesn't solve
the bugzilla entries.
v3: Another attempt to improve commit message.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau damien.lespiau@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The ultimate goal here is to remove the dependency we
currently have on audio driver power to get PSR working.
Since with audio driver runtime PM disabled the Hardware tracking
believes graphics is fully active and prevent PSR Entry, or
in other words continuously exit PSR.
So, the idea is to transfer the PSR exit responsability
from the HW tracking to the SW tracking (frontbuffer tracking),
who is really mature right now.
However with LPSP masked out there might be cases where we could
miss exit from HW tracking since it can be relying on this,
like a specific case reported at our mailing list who
user reported he would miss screen updates if scrolling firefox
in a Gnome environment when i915 runtimepm was enabled.
So before masking out LPSP again to make us independent from
the audio driver we need to make sure that all our cases
are coverred from the frontbuffer tracking perspective,
where the flush means invalidate and flush.
Without this patch for HSW, BDW and SKL we just do the
invalidate part when the flush wasn't originated by a page flip
because we were trusting the HW tracking for the flip case.
So let's rely more on frontbuffer tracking and do the
invalidation regardless the origin as expected for all platforms.
v2: Improve commit message as suggested by Paulo.
v3: Another attempt to let commit message more clear.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau damien.lespiau@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Commit (89251b17) intended to remove this line and let only one
DP_PSR_EN_CFG set, but it was wrong and this call is now duplicated
at the code.
Also "& ~DP_PSR_MAIN_LINK_ACTIVE" doesn't do anything at all. It
was like that since I introduced this call but probably the idea
was to be informative and make clear statement that we were not using
the link standby. So it is better to remove this one here and let
the code a bit cleaner.
v2: Improve commit message as requested by Paulo.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau damien.lespiau@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Commit e9f24d5fb7
Author: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Date: Mon Oct 5 13:26:36 2015 +0100
drm/i915: Clean up associated VMAs on context destruction
Added a warning based on an incorrect assumption that all VMAs
in a VM will be on the inactive list at the point last reference
to a context and VM is dropped.
This is not true because i915_gem_object_retire__read will not
put VMA on the inactive list until all activities on the object
in question (in all VMs) have been retired.
As a consequence, whether or not a context/VM will be destroyed
with its VMAs still on the active list, can depend on completely
unrelated activities using the same object from a different
context or engine.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92638
Testcase: igt/gem_request_retire/retire-vma-not-inactive
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448025816-25584-1-git-send-email-tvrtko.ursulin@linux.intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we experience a refcounting failure in a power domain/well (unref'ing at
least one too many times), log the name of the offending domain or well.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448034934-11926-2-git-send-email-daniels@collabora.com
Let us print human-parseable values from the power domain code; upcoming
display code also wants to use it.
This requires moving it out of i915_debugfs.c, as that is only conditionally
compiled.
v2: Move it out of the header.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448034934-11926-1-git-send-email-daniels@collabora.com
During suspend-to-idle we need to keep the DMC firmware active and DC6
enabled, since otherwise we won't reach deep system power states like
PC9/10. The lead for this came from Nivedita who noticed that the
kernel's turbostat tool didn't report any PC9/10 residency change
across an 'echo freeze > /sys/power/state'.
Reported-by: Nivedita Swaminathan <nivedita.swaminathan@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447860750-18110-1-git-send-email-imre.deak@intel.com
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWUmHZAAoJEHm+PkMAQRiGHtcH/RVRsn8re0WdRWYaTr9+Hknm
CGlRJN4LKecttgYQ/2bS1QsDbt8usDPBiiYVopqGXQxPBmjyDAqPjsa+8VzCaVc6
WA+9LDB+PcW28lD6BO+qSZCOAm7hHSZq7dtw9x658IqO+mI2mVeCybsAyunw2iWi
Kf5q90wq6tIBXuT8YH9MXGrSCQw00NclbYeYwB9CmCt9hT/koEFBdl7uFUFitB+Q
GSPTz5fXhgc5Lms85n7flZlrVKoQKmtDQe4/DvKZm+SjsATHU9ru89OxDBdS5gSG
YcEIM4zc9tMjhs3GC9t6WXf6iFOdctum8HOhUoIN/+LVfeOMRRwAhRVqtGJ//Xw=
=DCUg
-----END PGP SIGNATURE-----
Merge tag 'v4.4-rc2' into drm-intel-next-queued
Linux 4.4-rc2
Backmerge to get at
commit 1b0e3a049e
Author: Imre Deak <imre.deak@intel.com>
Date: Thu Nov 5 23:04:11 2015 +0200
drm/i915/skl: disable display side power well support for now
so that we can proplery re-eanble skl power wells in -next.
Conflicts are just adjacent lines changed, except for intel_fbdev.c
where we need to interleave the changs. Nothing nefarious.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
There are platforms that don't need the full GMBUS power domain (BXT)
while others do (PCH, VLV/CHV). For optimizing this we would need to add
a new power domain, but it's not clear how much we would benefit given
the short time we hold the reference. So for now let's keep things
simple.
v2:
- fix commit message, PCH won't take any redundant power resource after
this change (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[fix commit message in v2 (Imre)]
Link: http://patchwork.freedesktop.org/patch/msgid/1447959301-1263-2-git-send-email-imre.deak@intel.com
i915 fixes for 4.4, including the revert for the backlight regression
Olof reported. Otherwise fixes all around.
* tag 'drm-intel-fixes-2015-11-19' of git://anongit.freedesktop.org/drm-intel:
Revert "drm/i915: skip modeset if compatible for everyone."
drm/i915: Consider SPLL as another shared pll, v2.
drm/i915: Fix gpu frequency change tracing
drm/i915: Don't clobber the addfb2 ioctl params
drm/i915: Clear intel_crtc->atomic before updating it.
drm/i915: get runtime PM reference around GEM set_caching IOCTL
drm/i915: Fix GT frequency rounding
drm/i915: quirk backlight present on Macbook 4, 1
drm/i915: Fix crtc_y assignment in intel_find_initial_plane_obj()
Here are some drm core fixes for v4.4 that I've picked up. Atomic fixes
from Maarten, and atomic helper fixes from Ville and Daniel.
Admittedly the topmost commit didn't sit in our tree for very long, but
does come with reviews and testing from trustworthy people.
* tag 'topic/drm-fixes-2015-11-19' of git://anongit.freedesktop.org/drm-intel:
drm/atomic-helper: Check encoder/crtc constraints
drm: Fix primary plane size for stereo doubled modes for legacy setcrtc
drm/core: Fix old_fb handling in pan_display_atomic.
drm/core: Fix old_fb handling in restore_fbdev_mode_atomic.
drm/atomic: add a drm_atomic_clean_old_fb helper.
drm/core: Fix old_fb handling in drm_mode_atomic_ioctl.
drm/core: Set legacy_cursor_update in drm_atomic_helper_disable_plane.
Currently if intelfb_create() errors out, it unrefs the bo even though
the fb now owns that reference. (Spotted by Ville Syrjälä.) We should
unref the fb instead of the bo.
However the fb was not necessarily allocated by intelfb_create(),
it could be inherited from BIOS (the fb struct was then allocated by
dev_priv->display.get_initial_plane_config()) and be in active use by
a crtc. In this case we should call drm_framebuffer_remove() instead
of _unreference() to also disable the crtc.
Daniel Vetter suggested that "fbdev teardown code will take care of it.
The correct approach is probably to not unref anything at all".
But if fbdev initialization fails, the fbdev isn't torn down and
occupies memory even though it's unusable. Therefore clobber it in
intel_fbdev_initial_config(). (Currently we ignore a negative return
value there.) The idea is that if fbdev initialization fails, the driver
behaves as if CONFIG_DRM_FBDEV_EMULATION wasn't set. Should X11 manage
to start up without errors, it will at least be able to use the memory
that would otherwise be hogged by the unusable fbdev.
Also, log errors in intelfb_create().
Don't call async_synchronize_full() in intel_fbdev_fini() when called
from intel_fbdev_initial_config() to avoid deadlock.
v2: Instead of calling drm_framebuffer_unreference() (if fb was not
inherited from BIOS), call intel_fbdev_fini().
v3: Rebase on e00bf69644 (drm/i915: Move the fbdev async_schedule()
into intel_fbdev.c), call async_synchronize_full() conditionally
instead of moving it into i915_driver_unload().
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: http://patchwork.freedesktop.org/patch/msgid/49ce5f0daead24b7598ec78591731046c333c18d.1447938059.git.lukas@wunner.de
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 2e5356da37.
It is now redundant as it is already covered in below commit which introduced
the changes to reuse initialization of resources in resume/reset path.
commit e84fe80337
Author: Nick Hoath <nicholas.hoath@intel.com>
Date: Fri Sep 11 12:53:46 2015 +0100
drm/i915: Split alloc from init for lrc
lrc_setup_hardware_status_page() in the same function gen8_init_common_ring()
takes care of this.
Cc: Nick Hoath <nicholas.hoath@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447951664-9347-1-git-send-email-arun.siluvery@linux.intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intelfb_create() is called once on driver initialization. If it fails,
ifbdev->helper.fbdev, ifbdev->fb or ifbdev->fb->obj may be NULL.
Further up in the call stack, intel_fbdev_initial_config() calls
intel_fbdev_fini() to tear down the ifbdev on failure. This calls
intel_fbdev_destroy() which dereferences ifbdev->fb. Fix the ensuing
oops.
Also check in these functions if ifbdev is not NULL to avoid oops:
i915_gem_framebuffer_info() is called on access to debugfs file
"i915_gem_framebuffer" and dereferences ifbdev, ifbdev->helper.fb
and ifbdev->helper.fb->obj.
intel_connector_add_to_fbdev() / intel_connector_remove_from_fbdev()
are called when registering / unregistering an mst connector and
dereference ifbdev.
v3: Drop additional null pointer checks in intel_fbdev_set_suspend(),
intel_fbdev_output_poll_changed() and intel_fbdev_restore_mode()
since they already check if ifbdev is not NULL, which is sufficient
now that intel_fbdev_fini() is called on initialization failure.
(Requested by Daniel Vetter <daniel.vetter@ffwll.ch>)
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: http://patchwork.freedesktop.org/patch/msgid/d05f0edf121264a9d0adb8ca713fd8cc4ae068bf.1447938059.git.lukas@wunner.de
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The rotated view depends upon the rotation paramters, but thus far we
didn't bother checking for those. This seems to have been an issue
ever since this was introduce in
commit fe14d5f4e5
Author: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Date: Wed Dec 10 17:27:58 2014 +0000
drm/i915: Infrastructure for supporting different GGTT views per object
But userspace is allowed to reuse framebuffer backing storage with
different framebuffers with different pixel formats/stride/whatever.
And e.g. SNA indeed does this. Hence we must check for all the
paramters to match, not just that it's rotated.
v2: intel_plane_obj_offset also needs to construct the full view, to
avoid fallout since they don't fully match.
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1444834266-12689-3-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't need 2 separate unions.
Note that this was done intentinoally
Author: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Date: Wed May 6 14:35:38 2015 +0300
drm/i915: Add a partial GGTT view type
on Tvrtko's request, but without a clear justification. Rotated views
are also not checking for matching paramters in i915_ggtt_view_equal,
which seems like a bug. But this patch here doesn't change that.
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1444834266-12689-2-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It can't fail and there's even a WARN_ON suggesting that if it would,
it would be a disaster.
Correct this to make things less confusing.
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1444834266-12689-1-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This was totally lost when I originally created the atomic helpers.
We probably should also check possible_clones in the helpers, but
since the legacy ones didn't do that this is for a separate patch.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Stone <daniels@collabora.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447868808-10266-1-git-send-email-daniel.vetter@ffwll.ch
This reverts
commit 6764e9f872
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date: Thu Aug 27 15:44:06 2015 +0200
drm/i915: skip modeset if compatible for everyone.
Bring back the i915.fastboot module parameter, disabled by default, due
to backlight regression on Chromebook Pixel 2015.
Apparently the firmware of the Chromebook in question enables the panel
but disables backlight to avoid a brief garbage scanout upon loading the
kernel/module. With fastboot, we leave the backlight untouched, in this
case disabled. The user would have to do a modeset (i.e. not just crank
up the brightness) to enable the backlight.
There is no clean fix readily available, so get back to the drawing
board by reverting.
[N.B. The reference below is for when the thread was included on public
lists, and some of the context had already been dropped by then.]
Reported-and-tested-by: Olof Johansson <olof@lixom.net>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
References: http://marc.info/?i=CAKMK7uES7xk05ki92oeX6gmvZWAh9f2vL7yz=6T+fGK9J3X7cQ@mail.gmail.com
Fixes: 6764e9f872 ("drm/i915: skip modeset if compatible for everyone.")
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447921590-3785-1-git-send-email-jani.nikula@intel.com
Here are a few little VC4 fixes for 4.4 that I didn't get in to you
before the -next pull request. I dropped the feature-ish one I'd
mentioned, and also droppped the one I saw you included in the last
-fixes pull request.
* 'drm-vc4-fixes' of git://github.com/anholt/linux:
drm/vc4: Make sure that planes aren't scaled.
drm/vc4: Fix some failure to track __iomem decorations on pointers.
drm/vc4: checking for NULL instead of IS_ERR
drm/vc4: fix itnull.cocci warnings
drm/vc4: fix platform_no_drv_owner.cocci warnings
drm/vc4: vc4_plane_duplicate_state() can be static
Radeon and amdgpu fixes for 4.4. A bit more the usual since I missed
last week. Misc fixes all over the place. The big changes are the
tiling configuration fixes for Fiji.
* 'drm-fixes-4.4' of git://people.freedesktop.org/~agd5f/linux: (35 commits)
drm/amdgpu: reserve/unreserve objects out of map/unmap operations
drm/amdgpu: move bo_reserve out of amdgpu_vm_clear_bo
drm/amdgpu: add lock for interval tree in vm
drm/amdgpu: keep the owner for VMIDs
drm/amdgpu: move VM manager clean into the VM code again
drm/amdgpu: cleanup VM coding style
drm/amdgpu: remove unused VM manager field
drm/amdgpu: cleanup scheduler command submission
drm/amdgpu: fix typo in firmware name
drm/amdgpu: remove the unnecessary parameter adev for amdgpu_sa_bo_new()
drm/amdgpu: wait interruptible when semaphores are disabled v2
drm/amdgpu: update pd while updating vm as well
drm/amdgpu: fix handling order in scheduler CS
drm/amdgpu: fix incorrect mutex usage v3
drm/amdgpu: cleanup scheduler fence get/put dance
drm/amdgpu: add command submission workflow tracepoint
drm/amdgpu: update Fiji's tiling mode table
drm/amdgpu: fix bug that can't enter thermal interrupt for bonaire.
drm/amdgpu: fix seq_printf format string
drm/radeon: fix quirk for MSI R7 370 Armor 2X
...
MISSING_CASE() would have been useful to track down a recent problem in
intel_display_port_aux_power_domain(), so add it there and a few related
helpers. This was also suggested by Ville in his review of the latest
DMC/DC changes, we forgot to address that.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447855045-7109-2-git-send-email-imre.deak@intel.com
Due to the current sharing of the DDI encoder between DP and HDMI
connectors we can run the DP detection after the HDMI detection has
already set the shared encoder's type. For now solve this keeping the
current behavior and running the detection in this case too. For a proper
solution Ville suggested to split the encoder into an HDMI and DP one, that
can be done as a follow-up.
This issue triggers the WARN in intel_display_port_aux_power_domain() and
was introduced in:
commit 25f78f58e5
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Mon Nov 16 15:01:04 2015 +0100
drm/i915: Clean up AUX power domain handling
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447855045-7109-1-git-send-email-imre.deak@intel.com
Change-Id: Id6514f2fb6e002437fdbe99353d5d35f4ac736c7
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Change-Id: Ifbb0c06680494bfa04d0be5e5941d31ae2e5ef28
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Change-Id: I62b892a22af37b32e6b4aefca80a25cf45426ed2
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
We don't need the last VM use any more, keep the owner directly.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <davdi1.zhou@amd.com>
It's not a good idea to duplicate that code.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <davdi1.zhou@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Fix the indentation and move the VM functions to the structures.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <davdi1.zhou@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Unify the two code path again, cause they do pretty much the same thing.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <davdi1.zhou@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
That call was moved to intel_dp_detect() in
commit d410b56d74
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Sep 2 20:03:59 2014 +0100
drm/i915/dp: Refactor common eDP lid detection
but it seem to have been resurrected in the following commit, probably
due to a wrong merge conflict resolution.
commit 2a592bec50
Author: Dave Airlie <airlied@redhat.com>
Date: Mon Sep 1 16:58:12 2014 +1000
drm/i915: handle G45/GM45 pulse detection connected state.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447859970-9546-1-git-send-email-ander.conselvan.de.oliveira@intel.com
On the commit 3301d40921 ("drm/i915: PSR: Fix DP_PSR_NO_TRAIN_ON_EXIT logic")'
we already had identified that DP_PSR_NO_TRAIN_ON_EXIT
doesn't mean we shouldn't send TPS patterns, however we start sending the
minimal TP1 as possible and no TP2.
For most of the panels this is ok, but we found a reported case where
this is not true and panel keeps frozen without updating the screen for a while.
We could just get this case after patch "PSR: Don't Skip aux handshake on
DP_PSR_NO_TRAIN_ON_EXIT." is applied since that one fix the
hard freeze on this kind of panels.
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=91436#c19
Cc: Ivan Mitev <ivan.mitev@gmail.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since the beginning there is a confusion on the meaning of this bit.
A previous patch had identified this already and fixed it partially:
'commit 3301d409 ("drm/i915: PSR: Fix DP_PSR_NO_TRAIN_ON_EXIT logic")
DP_PSR_NO_TRAIN_ON_EXIT means the source doesn't need to do the
training, but it doesn't tell to avoid TP patterns or to skip
aux handshake.
This patch fixes the hard freeze reported.
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=91436
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=91437
Cc: Ivan Mitev <ivan.mitev@gmail.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With 'commit 30886c5a ("drm/i915: VLV/CHV PSR: Increase wait delay
time before active PSR.")' we fixed a blank screen when first
activation was happening immediately after PSR being enabled.
There we gave more time for idleness by increasing the delay
between re-activating sequences.
However, commit "drm/i915: Delay first PSR activation."
delay the first activation in a better way keeping a good PSR
residency. So, we can now reduce the delay on re-enable.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When debuging the frozen screen caused by HW tracking with low
power state I noticed that if we keep moving the mouse non stop
you will miss the screen updates for a while. At least
until we stop moving the mouse for a small time and move again.
The actual enabling should happen immediately after
Display Port enabling sequence finished with links trained and
everything enabled. However we face many issues when enabling PSR
right after a modeset.
On VLV/CHV we face blank screens on this scenario and on HSW+
we face a recoverable frozen screen, at least until next
exit-activate sequence.
Another workaround for the same issue here would be to increase
re-enable idle time from 100 to 500 as we did for VLV/CHV.
However this patch workaround this issue in a better
way since it doesn't reduce PSR residency and also
allow us to reduce the delay time between re-enables at least
on VLV/CHV.
This is also important to make the sysfs toggle working properly.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make I915_READ and I915_WRITE more type safe by wrapping the register
offset in a struct. This should eliminate most of the fumbles we've had
with misplaced parens.
This only takes care of normal mmio registers. We could extend the idea
to other register types and define each with its own struct. That way
you wouldn't be able to accidentally pass the wrong thing to a specific
register access function.
The gpio_reg setup is probably the ugliest thing left. But I figure I'd
just leave it for now, and wait for some divine inspiration to strike
before making it nice.
As for the generated code, it's actually a bit better sometimes. Eg.
looking at i915_irq_handler(), we can see the following change:
lea 0x70024(%rdx,%rax,1),%r9d
mov $0x1,%edx
- movslq %r9d,%r9
- mov %r9,%rsi
- mov %r9,-0x58(%rbp)
- callq *0xd8(%rbx)
+ mov %r9d,%esi
+ mov %r9d,-0x48(%rbp)
callq *0xd8(%rbx)
So previously gcc thought the register offset might be signed and
decided to sign extend it, just in case. The rest appears to be
mostly just minor shuffling of instructions.
v2: i915_mmio_reg_{offset,equal,valid}() helpers added
s/_REG/_MMIO/ in the register defines
mo more switch statements left to worry about
ring_emit stuff got sorted in a prep patch
cmd parser, lrc context and w/a batch buildup also in prep patch
vgpu stuff cleaned up and moved to a prep patch
all other unrelated changes split out
v3: Rebased due to BXT DSI/BLC, MOCS, etc.
v4: Rebased due to churn, s/i915_mmio_reg_t/i915_reg_t/
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1447853606-2751-1-git-send-email-ville.syrjala@linux.intel.com
When diagnosing a unrelated bug for someone on irc, it would seem the hardware can
be brought up by the BIOS with the embedded displayport using the SPLL for spread spectrum.
Right now this is not handled well in i915, and it calculates the crtc needs to
be reprogrammed on the first modeset without SSC, but the SPLL itself was kept
active. Fix this by exposing SPLL as a shared pll that will not be returned
by intel_get_shared_dpll; you have to know it exists to use it.
Changes since v1:
- Create a separate dpll_hw_state.spll for spll, and use
separate pll functions for spll.
Tested-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Gabriel Feceoru <gabriel.feceoru@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447681332-6318-1-git-send-email-maarten.lankhorst@linux.intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Ville Syrjälä