With the introduction of PCI it became apparent that s390 should
convert to generic hardirqs as too many drivers do not have the
correct dependency for GENERIC_HARDIRQS. On the architecture
level s390 does not have irq lines. It has external interrupts,
I/O interrupts and adapter interrupts. This patch hard-codes all
external interrupts as irq #1, all I/O interrupts as irq #2 and
all adapter interrupts as irq #3. The additional information from
the lowcore associated with the interrupt is stored in the
pt_regs of the interrupt frame, where the interrupt handler can
pick it up. For PCI/MSI interrupts the adapter interrupt handler
scans the relevant bit fields and calls generic_handle_irq with
the virtual irq number for the MSI interrupt.
Reviewed-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Uninline pci related instruction wrappers to de-bloat the code:
add/remove: 15/0 grow/shrink: 2/24 up/down: 1326/-12628 (-11302)
This is especially useful for the inlined pci read and write functions
which are used all over the kernel. Also remove the unused __stpcifc
while at it.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add support for reading the PCI function measurement block counters
provided by the hypervisor. Add two s390 debug features, one for
critical errors and one for tracing and provide wrappers to log data.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add some s390 specific sysfs attributes to the PCI device directory.
The following attributes are introduced:
- function_id (PCI function ID)
- function_handle (PCI function handle)
- pchid (PCI channel ID)
- pfgid (PCI function group ID aka PCI root complex)
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add CHSC store-event-information support for PCI (notfication type 2)
and report error and availability events to the PCI architecture layer.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add DMA IOMMU support using 4K page table entries. Implement dma_map_ops.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Support PCI adapter interrupts using the Single-IRQ-mode. Single-IRQ-mode
disables an adapter IRQ automatically after delivering it until the SIC
instruction enables it again. This is used to reduce the number of IRQs
for streaming workloads.
Up to 64 MSI handlers can be registered per PCI function.
A hash table is used to map interrupt numbers to MSI descriptors.
The interrupt vector is scanned using the flogr instruction.
Only MSI/MSI-X interrupts are supported, no legacy INTs.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
CLP instructions are used to query the firmware about detected PCI
functions, the attributes of those functions and to enable or disable
a PCI function. The CLP interface is the equivalent to a PCI bus scan.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add PCI support for s390, (only 64 bit mode is supported by hardware):
- PCI facility tests
- PCI instructions: pcilg, pcistg, pcistb, stpcifc, mpcifc, rpcit
- map readb/w/l/q and writeb/w/l/q to pcilg and pcistg instructions
- pci_iomap implementation
- memcpy_fromio/toio
- pci_root_ops using special pcilg/pcistg
- device, bus and domain allocation
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Martin Schwidefsky