Semi-planar YUV formats use two distinct planes, one for luminance and
one for chrominance. To add support for them, we need to configure the
second line stride and buffer address registers to setup the second YUV
plane.
New definitions are introduced to configure the input format register
for the YUV420 and YUV422 semi-planar formats.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190118145133.21281-10-paul.kocialkowski@bootlin.com
This introduces support for packed YUV formats with 4:2:2 sampling using
the frontend. Definitions are introduced for the data format and pixel
sequence input format register values.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190118145133.21281-9-paul.kocialkowski@bootlin.com
In prevision of adding support for YUV formats, set the YUV to RGB
colorspace conversion coefficients if required and don't bypass the
CSC engine when converting.
The BT601 coefficients from the A33 BSP are copied over from the backend
code. Because of module inter-dependency, we can't have the frontend use
these coefficients from the backend directly.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190118145133.21281-8-paul.kocialkowski@bootlin.com
Both the backend and the frontend need the BT.601 CSC coefficients for
YUV to RGB conversion. Since the backend has a dependency on the
frontend (and not the other way round), move the coefficients there
so that both can access them without having to duplicate them.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190118145133.21281-7-paul.kocialkowski@bootlin.com
Since all the RGB input formats have the same value for the DATA_FMT
field of the INPUT_FMT register, we can group them when the format is
known to be RGB. Here, we assume that a non-YUV format is RGB, because
the hardware does not support any other colorspace than RGB and YUV.
Use the DRM format info structure to check whether the format uses a
YUV colorspace.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190118145133.21281-6-paul.kocialkowski@bootlin.com
The helper returning the input mode needs to know the number of planes
for the provided format. Passing the fourcc requires iterating through
the format info list in order to return the number of planes.
Pass the DRM format info structure directly instead to all helpers
related to configuring the input format, since it's available to the
caller. Also rename the input format in the caller function to keep
things consistent.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190118145133.21281-5-paul.kocialkowski@bootlin.com
Checking for the number of planes is not sufficient to en ensure that
the format is a packed YUV422.
Use explicit fourcc helpers for the check instead.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190118145133.21281-4-paul.kocialkowski@bootlin.com
Make life easier for drivers by simply passing the connector
to drm_hdmi_avi_infoframe_from_display_mode() and
drm_hdmi_avi_infoframe_quant_range(). That way drivers don't
need to worry about is_hdmi2_sink mess.
v2: Make is_hdmi2_sink() return true for sil-sii8620
Adapt to omap/vc4 changes
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Sandy Huang <hjc@rock-chips.com>
Cc: "Heiko Stübner" <heiko@sntech.de>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: amd-gfx@lists.freedesktop.org
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Cc: nouveau@lists.freedesktop.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190108172828.15184-1-ville.syrjala@linux.intel.com
To prepare the introduction of tiled mode support, pass the framebuffer
format modifier to the helpers dealing with format support.
Since only linear mode is supported for now, add corresponding checks in
each helper.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-33-paul.kocialkowski@bootlin.com
Our hardware requires the pitch to be an even number when using YUV
formats with the frontend. Implement a driver-specific callback for GEM
dumb allocation that sets the pitch accordingly.
Since only the bpp is passed (and not the format), we cannot really
distinguish if this alignment is really required. Since it doesn't hurt
to align the pitch anyway, always do it.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-30-paul.kocialkowski@bootlin.com
The frontend comes with two "channels", that can be configured
independently. When used in YUV mode, the first channel (CH0) represents
the luminance component while the second channel (CH1) represents the
chrominance. In RGB mode, both have to be configured the same way.
Use variables (with the YUV terminology) for each channel's
dimensions, calculating the chroma dimensions from the luma dimensions
and the sub-sampling factors from the format description.
Since the configured size only has pixel precision, the fractional
fixed-point part of the source size is dropped for both components to
ensure that the scaling factors are accurate.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-26-paul.kocialkowski@bootlin.com
The values in the BT601 YUV to RGB colorspace translation are not
simply coded as multiples, but rather as fixed-point signed fractional
values on a given number of bits. Add an explanation about that.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-24-paul.kocialkowski@bootlin.com
This introduces support for the BGRX8888 input format for the frontend,
with its associated pixel sequence value definition. Other fields are
already configured correctly as they no longer depend on the format's
fourcc directly.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-22-paul.kocialkowski@bootlin.com
Use the number of planes associated with the DRM format to determine the
input mode configuration instead of the format iteself. This way, the
helper can be used for all packed formats without future changes.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-20-paul.kocialkowski@bootlin.com
This introduces proper definitions for the input and output format
configuration registers instead of a macro and raw values in the code,
with the intent to increase code readability and reduce indirections.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-19-paul.kocialkowski@bootlin.com
This introduces new helpers for retrieving the input data mode and pixel
sequence register field values based on the DRM format instead of
hardcoding these. This makes it easier to add support for more formats.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-18-paul.kocialkowski@bootlin.com
In order to support YUV to RGB conversion with the frontend (which is
generally used for connecting with the backend), the CSC block must not
be bypassed.
As a result, the bit to enable CSC bypass is moved from the runtime
resume routine to the format update routine, so that it can disabled
when introducing support for YUV formats later.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-17-paul.kocialkowski@bootlin.com
Since more formats can be supported by the frontend, rename the
variable listing the layer formats to avoid suggesting that the backend
itself supports all the listed formats.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-16-paul.kocialkowski@bootlin.com
Our hardware has a limited number of YUV planes (usually 1) that can be
supported using the backend only. However, YUV planes can also be
supported by the frontend and must then not be counted when checking for
that limitation.
Only count the YUV plane when the frontend is not used.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-15-paul.kocialkowski@bootlin.com
Before this patch, it is assumed that a plane is supported either
through the frontend or through the backend alone. However, the DRM
interface does not allow finely reporting our hardware capabilities
and there are cases where neither are support.
In particular, some plane formats are supported by the backend and not
the frontend, so they can only be supported without scaling.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-8-paul.kocialkowski@bootlin.com
Checking that scaling is in use is not sufficient as a condition to
decide to use the frontend.
Since not all layer formats are supported by the frontend, we need to
check for that support first. Then, the frontend must only be enabled
if the backend doesn't support the format or that scaling is required.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-7-paul.kocialkowski@bootlin.com
In order to check whether the frontend supports a specific format, an
explicit list and a related helper are introduced.
Just like in the backend, the prototype of the helper is added to the
frontend header so that it can be used later on. The helper is also
exported because it will be used outside of the frontend module.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-6-paul.kocialkowski@bootlin.com
In order to check whether the backend supports a specific format, an
explicit list and a related helper are introduced.
The prototype of this helper is added to the header so that it can be
called from sun4i_layer later (when introducing tiled mode support).
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-5-paul.kocialkowski@bootlin.com
The backend allows integer-only scaling but can handle alpha components,
unlike the frontend. It could be useful to add support for this
eventually, so add a short TODO comment describing the situation.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-4-paul.kocialkowski@bootlin.com
The frontend documentation (for the A33) mentions that ARGB is supported
as output, but with the alpha component always set to 0xff. In practice,
this means that the alpha component cannot be preserved when going
through the frontend. Since the information is lost, ARGB is not
properly supported.
As a result, expose the matching format supported by the frontend (both
for input and output) as XRGB instead of ARGB.
Since ARGB was the selected format for connecting the frontend to the
backend, change it to XRGB to reflect this as well.
The A31 and A80 SoCs apparently have a bit to enable proper alpha,
but this is not supported at this point (see the comment already in the
code).
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-3-paul.kocialkowski@bootlin.com
This adds a dedicated function for cleaning the video and YUV source
channel layer enable bits. This function is called first on layer atomic
update to make sure that there are no leftover bits from previous
plane configuration that were not cleaned until now.
It fixes issues when alternating between video and YUV planes, where
both bits would be set eventually, leading to broken plane display.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-2-paul.kocialkowski@bootlin.com
Render like lima will attach a fence to the framebuffer
dma_buf, display like sun4i should wait it finish before
show the framebuffer. Otherwise tearing will be observed.
Signed-off-by: Qiang Yu <yuq825@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181122014417.23285-1-yuq825@gmail.com
drm-next is forwarded to v4.20-rc1, and we need this to make
a patch series apply.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Some panels need an active-low data enable (DE) signal for the RGB
interface. This requires flipping a bit in the TCON0 polarity register
when setting up the mode for the RGB interface.
Match the associated bus flag and use it to set the polarity inversion
bit for the DE signal when required.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181107181843.27628-4-contact@paulk.fr
Features such as dithering and pixel data edge configuration currently
rely on the panel registered with the TCON driver. However, bridges are
also supported in addition to panels for RGB setup.
Instead of retrieving the connector from the panel, get it from the
encoder with the dedicated helper.
Even in the case of bridges, the connector is registered with the
encoder from our driver and is accessible when iterating connectors.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181107181843.27628-3-contact@paulk.fr
Passing the encoder to the TCON RGB setup functions allows accessing the
connector from the encoder directly instead of relying on the panel.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181107181843.27628-2-contact@paulk.fr
Some SoCs, such as H6, doesn't have a full-featured TCON TOP.
Add quirks support for TCON TOP.
Currently the presence of TCON_TV1 and DSI is controlled via the quirks
structure.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[Fixed code style and removed unnecessary initialization]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-25-jernej.skrabec@siol.net
It turns out that TCON TOP registers in H6 SoC have non-zero reset
value. This may cause issues if bits are not changed during
configuration.
To prevent that, initialize registers to 0.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-24-jernej.skrabec@siol.net
H6 has Synopsys DWC HDMI 2.0 TX PHY.
There is no freely available documentation for it, only code found in
BSP kernel. However, judging by the code, PHY is very similar to older
Synopsys HDMI PHY described in i.MX6 documentation. Most registers seem
to be the same.
According to i.MX6 documentation, mpll settings are based on pixel clock
and are not specific to each SoC. Because of that, mpll table in this
commit is based on that documentation and not on BSP code. Other PHY
settings were derived from BSP PHY driver code.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-23-jernej.skrabec@siol.net
Currently sun8i-hdmi-phy driver supports only custom PHYs connected to
DW HDMI controller. Since newest Allwinner SoCs have unmodified Synopsys
PHY, driver has to be reorganized to support them.
Variant structure is expanded to allow differentiation between custom
and Sysnopsys PHYs and to hold Synopsys PHY settings.
Since DW HDMI bridge platform data has different fields for custom and
Sysnopsys PHY, function sun8i_hdmi_phy_get_ops() is replaced with
sun8i_hdmi_phy_set_ops().
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-22-jernej.skrabec@siol.net
Currently, quirks and compatibles are sorted alphabetically. However,
they should be sorted by family release date and then alphabetically.
Fix that by moving A64 quirks and compatible to bottom. No functional
change is made.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-21-jernej.skrabec@siol.net
It turns out that H6 HDMI BSP kernel driver doesn't change TMDS rate at
all. At this point it is not clear whether it is just not necessary or
it would cause some kind of issues.
Add a quirk for it.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-18-jernej.skrabec@siol.net
Since it is not possible to access sun8i-dw-hdmi driver private data
inside mode_valid function, make it configurable. That way different
versions of HDMI controllers can set different function, depending on
it's limitations.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-17-jernej.skrabec@siol.net
Currently supported Allwinner SoCs with DW HDMI controller have
scrambled addresses and read lock. However, that is not true in general.
For example, A80 and H6 have normal addresses and normal read access.
Move code for unscrambling addresses and unlocking read access to it's
own function and call it from init function.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-16-jernej.skrabec@siol.net
Mixer 0 has 1 VI and 3 UI planes, scaler on all planes and can output
4K image @60Hz. It also support 10 bit colors, which are not yet
implemented.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-14-jernej.skrabec@siol.net
Display Engine 3 is an upgrade of DE2 with new features like support for
10 bit color formats and support for AFBC.
Most of DE2 code works with DE3, except some small details.
Implement basic support for DE3. Support for 10 bit colort formats and
AFBC, among others missing features, will be added later.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/260238/
Most, if not all, registers found in DE2 still exists in DE3. However,
units are on different base addresses.
To prepare for addition of DE3 support, registers macros are reworked so
they take base address as parameter.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
[rebased]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-10-jernej.skrabec@siol.net
The CMA helper is already using the drm_fb_helper_generic_probe part of
the generic fbdev emulation. This patch makes full use of the generic
fbdev emulation by using its drm_client callbacks. This means that
drm_mode_config_funcs->output_poll_changed and drm_driver->lastclose are
now handled by the emulation code. Additionally fbdev unregister happens
automatically on drm_dev_unregister().
The drm_fbdev_generic_setup() call is put after drm_dev_register() in the
driver. This is done to highlight the fact that fbdev emulation is an
internal client that makes use of the driver, it is not part of the
driver as such. If fbdev setup fails, an error is printed, but the driver
succeeds probing.
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181025201340.34227-8-noralf@tronnes.org
The is_double flag is a boolean currently assigned to the value of the d
variable, that is either 1 or 2. It means that this is_double variable is
always set to true, even though the initial intent was to have it set to
true when d is 2.
Fix this.
Fixes: 9c5681011a ("drm/sun4i: Add HDMI support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181021163446.29135-2-maxime.ripard@bootlin.com
Paul Kocialkowski