add snvs power key driver.
It work in imx chips after i.mx6sx
ON/OFF key used power on/off whole system.
This driver make it wakeup from suspend state when short press
ON/OFF key.
Long time press will trig SNVS power off chip without software
intervention.
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The original wait time was 200ms which was enough for the firmware to
finish loading and boot. After that the firmware will perform
initialization and touch calibration, which will take about 1.1 second. The
touch calibration will change controller frequency to scan at the most
optimal frequency and during calibration/frequency switching process we may
run into i2c data errors. To avoid them we extend the sleep to 2500ms after
issuing the sw reset.
Signed-off-by: HungNien Chen <hn.chen@weidahitech.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
These attributes can be used to identify controllers present in the system.
Signed-off-by: HungNien Chen <hn.chen@weidahitech.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch to using standard touchscreen device properties parsing module
instead of doing it by hand in the driver.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
input_mt_init_slots() will perform necessary settings for performing
multi-touch to single-touch emulation, we do not need to do that ourselves.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The controller has a RESET pin which is usually controlled over
a GPIO line. If such a GPIO is provided, perform a RESET
during probe.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We are using threaded interrupt handler and thus are allowed to sleep.
Let's switch over to gpiod_get_value_cansleep() so that we do not get
ugly warnings in case GPIO controller might sleep when accessing GPIO.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This allows uniform parsing on legacy, DT and ACPI systems.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's move driver's platform data definitions from include/linux/input/
into include/linux/platform_data/ so that it stays with the rest of
platform data definitions.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch form OF to device properties so that common parsing code could
work not only on device tree but also on ACPI-based platforms.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The binding specification says that "touchscreen-size-x" and "-y" specify
horizontal and vertical resolution of the touchscreen and therefore maximum
absolute coordinates should be reduced by 1 since we are starting with 0.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Do issue warning about axis that is present in device tree but not specified
by the driver even in case of multi-touch axis as callers now tell us if they
expect multi-touch data or not.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
"A fix (revert) for a recent regression in Synaptics driver and a fix
for Elan i2c touchpad driver"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: synaptics - allocate 3 slots to keep stability in image sensors"
Input: elan_i2c - change the hover event from MT to ST
Use for_each_set_bit to check for set bits in bitmap
as it is more efficient and compact.
Signed-off-by: Anshul Garg <aksgarg1989@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use for_each_set_bit to check for set bits in bitmap
as it is more efficient than checking individual bits.
Signed-off-by: Anshul Garg <aksgarg1989@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use for_each_set_bit to check for set bits in bitmap as it is more
efficient than checking individual bits.
Signed-off-by: Anshul Garg <aksgarg1989@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
These reg_default tables are not modified after initialized, so make them
const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use the new GPIO descriptor interface to handle the zForce GPIOs.
This simplifies the code and allows transparently handle GPIO polarity, as
specified in device tree data.
Also switch to using gpio_{set|get}_value_cansleep() since none of the
callers is in atomic context and cansleep variant allows more GPIO
controllers to be used with the touchscreen.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Despite it's name, sign_extend32() is used for 16 bit values aswell.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The firmware only reports hover condition while the very first contact is
approaching the surface; the hover is not reported for the subsequent
contacts. Therefore we should not be using ABS_MT_DISTANCE to report hover
but rather its single-touch counterpart ABS_DISTANCE.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Now that there is no paravirt TSC, the "native" is
inappropriate. The function does RDTSC, so give it the obvious
name: rdtsc().
Suggested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang Rui <ray.huang@amd.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kvm ML <kvm@vger.kernel.org>
Link: http://lkml.kernel.org/r/fd43e16281991f096c1e4d21574d9e1402c62d39.1434501121.git.luto@kernel.org
[ Ported it to v4.2-rc1. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
It's unclear to me why this code exists in the first place.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang Rui <ray.huang@amd.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kvm ML <kvm@vger.kernel.org>
Cc: linux-input@vger.kernel.org
Link: http://lkml.kernel.org/r/9e058e72f4cf1f13c6483c1360b39c3d188a2c2a.1434501121.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This timing code is hideous, and this doesn't help. It gets rid
of one of the last users of rdtscl(), though.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang Rui <ray.huang@amd.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kvm ML <kvm@vger.kernel.org>
Cc: linux-input@vger.kernel.org
Link: http://lkml.kernel.org/r/90d19b3cea0e05ca6f333d1598daa38afb993260.1434501121.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull second round of input updates from Dmitry Torokhov:
"A new driver for Weida wdt87xx touch controllers, and a bunch of
fixups for other drivers"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wdt87xx_i2c - add a scaling factor for TOUCH_MAJOR event
Input: wdt87xx_i2c - remove stray newline in diagnostic message
Input: arc_ps2 - add HAS_IOMEM dependency
Input: wdt87xx_i2c - fix format warning
Input: improve parsing OF parameters for touchscreens
Input: edt-ft5x06 - mark as direct input device
Input: use for_each_set_bit() where appropriate
Input: add a driver for wdt87xx touchscreen controller
Input: axp20x-pek - fix reporting button state as inverted
Input: xpad - re-send LED command on present event
Input: xpad - set the LEDs properly on XBox Wireless controllers
Input: imx_keypad - check for clk_prepare_enable() error
Get the scaling factor when it reads the sys params. The width value will
multiple the factor and report the value in the TOUCH_MAJOR event.
Signed-off-by: HungNien Chen <hn.chen@weidahitech.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Main excitement here is Peter Zijlstra's lockless rbtree optimization to
speed module address lookup. He found some abusers of the module lock
doing that too.
A little bit of parameter work here too; including Dan Streetman's breaking
up the big param mutex so writing a parameter can load another module (yeah,
really). Unfortunately that broke the usual suspects, !CONFIG_MODULES and
!CONFIG_SYSFS, so those fixes were appended too.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tWPQ
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module updates from Rusty Russell:
"Main excitement here is Peter Zijlstra's lockless rbtree optimization
to speed module address lookup. He found some abusers of the module
lock doing that too.
A little bit of parameter work here too; including Dan Streetman's
breaking up the big param mutex so writing a parameter can load
another module (yeah, really). Unfortunately that broke the usual
suspects, !CONFIG_MODULES and !CONFIG_SYSFS, so those fixes were
appended too"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (26 commits)
modules: only use mod->param_lock if CONFIG_MODULES
param: fix module param locks when !CONFIG_SYSFS.
rcu: merge fix for Convert ACCESS_ONCE() to READ_ONCE() and WRITE_ONCE()
module: add per-module param_lock
module: make perm const
params: suppress unused variable error, warn once just in case code changes.
modules: clarify CONFIG_MODULE_COMPRESS help, suggest 'N'.
kernel/module.c: avoid ifdefs for sig_enforce declaration
kernel/workqueue.c: remove ifdefs over wq_power_efficient
kernel/params.c: export param_ops_bool_enable_only
kernel/params.c: generalize bool_enable_only
kernel/module.c: use generic module param operaters for sig_enforce
kernel/params: constify struct kernel_param_ops uses
sysfs: tightened sysfs permission checks
module: Rework module_addr_{min,max}
module: Use __module_address() for module_address_lookup()
module: Make the mod_tree stuff conditional on PERF_EVENTS || TRACING
module: Optimize __module_address() using a latched RB-tree
rbtree: Implement generic latch_tree
seqlock: Introduce raw_read_seqcount_latch()
...
Fix this compile error:
drivers/built-in.o: In function `arc_ps2_probe':
/mnt/linux/drivers/input/serio/arc_ps2.c:206: undefined reference to `devm_ioremap_resource'
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This fixes the following warning:
drivers/input/touchscreen/wdt87xx_i2c.c: In function 'wdt87xx_validate_firmware':
>> drivers/input/touchscreen/wdt87xx_i2c.c:472:4: warning: format '%zd' expects argument of type 'signed size_t', but argument 4 has type 'size_t' [-Wformat=]
size, fw->size);
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Here's the tty and serial driver patches for 4.2-rc1.
A number of individual driver updates, some code cleanups, and other
minor things, full details in the shortlog.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlWNoSAACgkQMUfUDdst+ymxNQCguSEmkAYNDdLyYhdcOqSxJt9u
U1gAoMThUDoomkx6CTDMU1wn53hxgMk9
=eCUS
-----END PGP SIGNATURE-----
Merge tag 'tty-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here's the tty and serial driver patches for 4.2-rc1.
A number of individual driver updates, some code cleanups, and other
minor things, full details in the shortlog.
All have been in linux-next for a while with no reported issues"
* tag 'tty-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (152 commits)
Doc: serial-rs485.txt: update RS485 driver interface
Doc: tty.txt: remove mention of the BKL
MAINTAINERS: tty: add serial docs directory
serial: sprd: check for NULL after calling devm_clk_get
serial: 8250_pci: Correct uartclk for xr17v35x expansion chips
serial: 8250_pci: Add support for 12 port Exar boards
serial: 8250_uniphier: add bindings document for UniPhier UART
serial: core: cleanup in uart_get_baud_rate()
serial: stm32-usart: Add STM32 USART Driver
tty/serial: kill off set_irq_flags usage
tty: move linux/gsmmux.h to uapi
doc: dt: add documentation for nxp,lpc1850-uart
serial: 8250: add LPC18xx/43xx UART driver
serial: 8250_uniphier: add UniPhier serial driver
serial: 8250_dw: support ACPI platforms with integrated DMA engine
serial: of_serial: check the return value of clk_prepare_enable()
serial: of_serial: use devm_clk_get() instead of clk_get()
serial: earlycon: Add support for big-endian MMIO accesses
serial: sirf: use hrtimer for data rx
serial: sirf: correct the fifo empty_bit
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=iJ/U
-----END PGP SIGNATURE-----
Merge tag 'media/v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Lots of improvements at the DVB API DocBook documentation. Now, the
frontend and the network APIs are fully in sync with the Kernel and
looks more like the rest of the media documentation;
- New frontend driver: cx24120
- New driver for a PCI device: cobalt. This driver is actually not
sold in the market, but it is a good example of a multi-HDMI input
device;
- The dt3155 driver were promoted from staging;
- The mantis driver got remote controller support;
- New V4L2 driver for ST bdisp SoC chipsets;
- Make sparse and smatch happier: several bugs were solved by fixing
the issues reported by those static code analyzers.
- Lots of new device additions, new features, improvements and cleanups
at the existing drivers.
* tag 'media/v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (553 commits)
[media] lmedm04: fix the range for relative measurements
[media] lmedm04: use u32 instead of u64 for relative stats
[media] omap3isp: remove unused var
[media] saa7134: fix page size on some archs
[media] use CONFIG_PM_SLEEP for suspend/resume
[media] tuner-i2c: be consistent with I2C declaration
[media] si470x: cleanup define namespace
[media] bdisp: prevent compiling on random arch
[media] vb2: Don't WARN when v4l2_buffer.bytesused is 0 for multiplanar buffers
[media] MAINTAINERS: Add entry for the Renesas VSP1 driver
[media] videodev2.h: fix copy-and-paste error in V4L2_MAP_XFER_FUNC_DEFAULT
[media] Revert "[media] vb2: Push mmap_sem down to memops"
[media] mantis: cleanup a warning
[media] bdisp-debug: don't try to divide by s64
[media] cx88: don't declare restart_video_queue if not used
[media] au0828: move dev->boards atribuition to happen earlier
[media] lmedm04: implement dvb v5 statistics
[media] bdisp: remove unused var
[media] bdisp: remove needless check
ts2020: fix compilation on i386
...
When applying touchscreen parameters specified in device tree let's make
sure we keep whatever setup was done by the driver and not reset the
missing values to zero.
Reported-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
edt-ft5x06 is a touchscreen and thus a direct input device; let's amrk it
as such. This also allows us to drop some initialization code as
input_init_mt_slots() will do that for us.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of iterating over all bits in a bitmap and test them individually
let's siwtch to for_each_set_bit() which is more compact and is also
faster.
Also use bitmap_weight() when counting number of set bits.
This also fixes INPUT_DO_TOGGLE() implementation as it should have used
*_CNT as the upper boundary, not *_MAX.
Signed-off-by: Anshul Garg <aksgarg1989@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input subsystem updates from Dmitry Torokhov:
"Thanks to Samuel Thibault input device (keyboard) LEDs are no longer
hardwired within the input core but use LED subsystem and so allow use
of different triggers; Hans de Goede did a large update for the ALPS
touchpad driver; we have new TI drv2665 haptics driver and DA9063
OnKey driver, and host of other drivers got various fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (55 commits)
Input: pixcir_i2c_ts - fix receive error
MAINTAINERS: remove non existent input mt git tree
Input: improve usage of gpiod API
tty/vt/keyboard: define LED triggers for VT keyboard lock states
tty/vt/keyboard: define LED triggers for VT LED states
Input: export LEDs as class devices in sysfs
Input: cyttsp4 - use swap() in cyttsp4_get_touch()
Input: goodix - do not explicitly set evbits in input device
Input: goodix - export id and version read from device
Input: goodix - fix variable length array warning
Input: goodix - fix alignment issues
Input: add OnKey driver for DA9063 MFD part
Input: elan_i2c - add product IDs FW names
Input: elan_i2c - add support for multi IC type and iap format
Input: focaltech - report finger width to userspace
tty: remove platform_sysrq_reset_seq
Input: synaptics_i2c - use proper boolean values
Input: psmouse - use true instead of 1 for boolean values
Input: cyapa - fix a few typos in comments
Input: stmpe-ts - enforce device tree only mode
...
This is a driver for Weida HiTech WDT87xx series touchscreen controller.
Signed-off-by: HungNien Chen <hn.chen@weidahitech.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Currently we are reporting the button state as inverted on all boards with
an axp209 pmic, tested on a ba10-tvbox, bananapi, bananapro, cubietruck and
utoo-p66 tablet.
The axp209 datasheet clearly states that the power button must be connected
between the PWRON key and ground. Which means that on a press we will get
a falling edge (dbf) irq not a rising one, and likewise on release we will
get a rising edge (dbr) irq, not a falling one.
This commit swaps the check for the 2 irqs fixing the inverted reporting of
the power button state.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The controller only receives commands when its present. So for the
correct LED to be lit the LED command has to be sent on the present
event.
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Based on Patch by Pierre-Loup A. Griffais <pgriffais@valvesoftware.com>:
Add the logic to set the LEDs on XBox Wireless controllers. Command
sequence found by sniffing the Windows data stream when plugging the
device in.
Updated based on comments on linux-input:
unify codepaths in xpad_send_led_command for wired/ wireless controller.
Also document command values for clarification.
All values tested on Xbox 360 Wireless Controller.
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
clk_prepare_enable() may fail, so we should better check its return value
and propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The i2c_master_recv() uses readsize to receive data from i2c but compares
to size of rdbuf which is always 27. This would cause problem when the
max_fingers is not 5. Change the comparison value to readsize instead.
Fixes: 36874c7e21 ("Input: pixcir_i2c_ts - support up to 5 fingers and
hardware tracking IDs:)
Cc: stable@vger.kernel.org
Signed-off-by: Frodo Lai <frodo_lai@bcmcom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for
output. Simplify drivers accordingly.
Note that in the case of the drv260x driver error checking is more
strict now because -ENOSYS is reported to the caller now. But this
should only be returned if GPIOLIB is disabled which shouldn't happen as
the driver depends on GPIOLIB.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Chromebooks can have more than one Embedded Controller so the
cros_ec device id has to be incremented for each EC registered.
Add a new structure to represent multiple EC as different char
devices (e.g: /dev/cros_ec, /dev/cros_pd). It connects to
cros_ec_device and allows sysfs inferface for cros_pd.
Also reduce number of allocated objects, make chromeos sysfs
class object a static and add refcounting to prevent object
deletion while command is in progress.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The MFD driver should only have the logic to instantiate its child devices
and setup any shared resources that will be used by the subdevices drivers.
The cros_ec MFD is more complex than expected since it also has helpers to
communicate with the EC. So the driver will only get more bigger as other
protocols are supported in the future. So move the communication protocol
helpers to its own driver as drivers/platform/chrome/cros_ec_proto.c.
Suggested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Commit 1b84f2a4cd ("mfd: cros_ec: Use fixed size arrays to transfer
data with the EC") modified the struct cros_ec_command fields to not
use pointers for the input and output buffers and use fixed length
arrays instead.
This change was made because the cros_ec ioctl API uses that struct
cros_ec_command to allow user-space to send commands to the EC and
to get data from the EC. So using pointers made the API not 64-bit
safe. Unfortunately this approach was not flexible enough for all
the use-cases since there may be a need to send larger commands
on newer versions of the EC command protocol.
So to avoid to choose a constant length that it may be too big for
most commands and thus wasting memory and CPU cycles on copy from
and to user-space or having a size that is too small for some big
commands, use a zero-length array that is both 64-bit safe and
flexible. The same buffer is used for both output and input data
so the maximum of these values should be used to allocate it.
Suggested-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This change creates a new input handler called "leds" that exports LEDs on input
devices as standard LED class devices in sysfs and allows controlling their
state via sysfs or via any of the standard LED triggers. This allows to
re-purpose and reassign LDEs on the keyboards to represent states other
than the standard keyboard states (CapsLock, NumLock, etc).
The old API of controlling input LEDs by writing into /dev/input/eventX
devices is still present and will take precedence over accessing via LEDs
subsystem (i.e. it may override state set by a trigger). If input device is
"grabbed" then requests coming through LED subsystem will be ignored.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Tested-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use kernel.h macro definition.
Thanks to Julia Lawall for Coccinelle scripting support.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
input_mt_init_slots() will do that for us.
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input layer fix from Dmitry Torokhov:
"A small tweak for the Synaptics PS/2 touchpad driver"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics - add min/max quirk for Lenovo S540
Goodix touchscreens export through their registers a Product ID and
Firmware Version. The Product ID is an ASCII encoding of the product name
(e.g.: "911").
Export to sysfs (through the input subsystem) the product id and firmware
version read from the device rather than using constant values.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Acked-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fix sparse warning:
drivers/input/touchscreen/goodix.c:182:26: warning: Variable length array is used.
Replace the variable length array with fixed length.
Some Goodix devices have maximum 5 touch points, while others have 10 touch
points. Using the maximum length (80 bytes) for all devices will lead to
wasting 40 bytes on stack when using devices with maximum 5 touch points.
However, that is preferable to using kmalloc which will use even more
resources.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Acked-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds OnKey driver support for DA9063.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Previously the elan_i2c touchpad driver would simply request the firmware
"/lib/firmware/elan_i2c.bin", which does not work well if there are
multiple such devices in the system.
Let's append the "product ID" (by using the same function as the sysfs
interface for consistency) to the filename. This results in filenames of
the form "/lib/firmware/elan_i2c_72.0.bin", allowing you to support
multiple elan_i2c touchpads on the same device by simply naming each
device's FW with its corresponding product ID. This way when you trigger a
fw update the driver will load the correct binary.
Signed-off-by: Charlie Mooney <charliemooney@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In order to support multiple IC types for i2c/smbus protocol, add get ic
type command and use this data when checking firmware page count and
signature address.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This fixes up a merge issue with the amba-pl011.c driver, and we want
the fixes in this branch as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull input subsystem fixes from Dmitry Torokhov:
"Just a couple touchpad drivers fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: alps - do not reduce trackpoint speed by half
Input: elantech - add new icbody type
Input: elantech - fix detection of touchpads where the revision matches a known rate
On some v7 devices (e.g. Lenovo-E550) the deltas reported are typically
only in the 0-1 range dividing this by 2 results in a range of 0-0.
And even for v7 devices where this does not lead to making the trackstick
entirely unusable, it makes it twice as slow as before we added v7 support
and were using the ps/2 mouse emulation of the dual point setup.
If some kind of generic slowdown is actually necessary for some devices,
then that belongs in userspace, not in the kernel.
Cc: stable@vger.kernel.org
Reported-and-tested-by: Rico Moorman <rico.moorman@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds new icbody type to the list recognized by Elantech PS/2 driver.
Cc: stable@vger.kernel.org
Signed-off-by: Sam Hung <sam.hung@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Focaltech touchpads report finger width in packet[5] of absolute packet.
Range for width in raw format is 0x10 - 0x70. Second half-byte is always 0.
0xff is reported, when a large contact area is detected.
This can be handled in userspace.
Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make the check to skip the rate check more lax, so that it applies
to all hw_version 4 models.
This fixes the touchpad not being detected properly on Asus PU551LA
laptops.
Cc: stable@vger.kernel.org
Reported-and-tested-by: David Zafra Gómez <dezeta@klo.es>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When stop_streaming is called while a frame is currently being retrieved, the
buffer being filled will still be returned with BUF_STATE_DONE. By resetting
the sequence number and checking before returning the buffer, it can now
correctly be returned with BUF_STATE_ERROR.
Signed-off-by: Martin Kaltenbrunner <modin@yuri.at>
Signed-off-by: Florian Echtler <floe@butterbrot.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add dev_dbg statements for easier future debugging; also change the warning
about packet ID mismatches to debug output to avoid flooding the logs. This
warning is only important in a very specific/rare use case when trying to
correlate input events with video data.
Signed-off-by: Martin Kaltenbrunner <modin@yuri.at>
Signed-off-by: Florian Echtler <floe@butterbrot.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add missing functions to query the single fixed frame size (960x540) and
supported frame rates. Technically, the SUR40 supports any arbitrary frame
rate up to 60 FPS, as it is polled and not interrupt-driven. For now, we
just report 30 and 60 FPS, which is sufficient to make most V4L2 tools work.
Signed-off-by: Martin Kaltenbrunner <modin@yuri.at>
Signed-off-by: Florian Echtler <floe@butterbrot.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The SUR40 hardware can deliver images at up to 60 FPS; at full USB2 bandwidth,
one raw frame will take about 11 ms to transmit. If the poll interval is above
5 ms, fully handling one frame will take longer than 16 ms and the overall
frame rate will drop below 60 FPS. To get the full frame rate without blocking
all the time and still allowing for a bit of timing jitter, we reduce the poll
interval to 4 ms.
Signed-off-by: Martin Kaltenbrunner <modin@yuri.at>
Signed-off-by: Florian Echtler <floe@butterbrot.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Most code already uses consts for the struct kernel_param_ops,
sweep the kernel for the last offending stragglers. Other than
include/linux/moduleparam.h and kernel/params.c all other changes
were generated with the following Coccinelle SmPL patch. Merge
conflicts between trees can be handled with Coccinelle.
In the future git could get Coccinelle merge support to deal with
patch --> fail --> grammar --> Coccinelle --> new patch conflicts
automatically for us on patches where the grammar is available and
the patch is of high confidence. Consider this a feature request.
Test compiled on x86_64 against:
* allnoconfig
* allmodconfig
* allyesconfig
@ const_found @
identifier ops;
@@
const struct kernel_param_ops ops = {
};
@ const_not_found depends on !const_found @
identifier ops;
@@
-struct kernel_param_ops ops = {
+const struct kernel_param_ops ops = {
};
Generated-by: Coccinelle SmPL
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Junio C Hamano <gitster@pobox.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: cocci@systeme.lip6.fr
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The variable no_decel is bool type so assigning "true" instead of "1".
Also, synaptics_i2c_get_input() has bool return type, so let's use "false"
there.
Signed-off-by: Shailendra Verma <shailendra.capricorn@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The variable psmouse_smartscroll is bool type so assigning true
instead of 1.
Signed-off-by: Shailendra Verma <shailendra.capricorn@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The STMPE MFD is only used with device tree configured systems (and STMPE
MFD core depends on OF), so force the configuration to come from device
tree only.
Tested-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When STMPE is instantiated via device tree individual MFD cells rae formed
with OF modaliases, not platform modaliases, and so we need to add OF
device table to the driver if we want it to load automatically:
of:Nstmpe_touchscreenT<NULL>Cst,stmpe-ts
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
"Updates for the input subsystem.
The main change is that we tell joydev not to touch "absolute mice",
such as VMware virtual mouse, as that produced bad result (cursor
stuck in upper right corner) with games"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: smtpe-ts - wait 50mS until polling for pen-up
Input: smtpe-ts - use msecs_to_jiffies() instead of HZ
Input: joydev - don't classify the vmmouse as a joystick
Input: vmmouse - do not reference non-existing version of X driver
Input: alps - fix finger jumps on lifting 2 fingers on v7 touchpad
Input: elantech - fix semi-mt protocol for v3 HW
Input: sx8654 - fix memory allocation check
rajeev-dlh.kumar@st.com email-id doesn't exist anymore as I have left the
company.
Signed-off-by: Rajeev Kumar <rajeevkumar.linux@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
gcc-5 defaults to gnu11 which used c99 inline semantics in c99 'inline' is
not externally visible unlike gnu89, therefore we use 'static inline' which
has same semantics between gnu89 and c99
Signed-off-by: Khem Raj <raj.khem@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Wait a little bit longer, 50mS instead of 20mS, until the driver starts
polling for pen-up. The problematic behavior before this patch is applied
is as follows. The behavior was observed on the STMPE610QTR controller.
Upon a physical pen-down event, the touchscreen reports one set of x-y-p
coordinates and a pen-down event. After that, the pen-up polling is
triggered and since the controller is not ready yet, the polling mistakenly
detects a pen-up event while the physical state is still such that the pen
is down on the touch surface.
The pen-up handling flushes the controller FIFO, so after that, all the
samples in the controller are discarded. The controller becomes ready
shortly after this bogus pen-up handling and does generate again a pen-down
interrupt. This time, the controller contains x-y-p samples which all read
as zero. Since pressure value is zero, this set of samples is effectively
ignored by userland.
In the end, the driver just bounces between pen-down and bogus pen-up
handling, generating no useful results. Fix this by giving the controller a
bit more time before polling it for pen-up.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use msecs_to_jiffies(20) instead of plain (HZ / 50), as the former is much
more explicit about it's behavior. We want to schedule the task 20 mS from
now, so make it explicit in the code.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The I2C subsystem can match devices without explicit OF support based on
the part of their compatible property after the comma. However, this
mechanism uses the first compatible value only. For adxl34x OF device
nodes the compatible property will contain the more specific
"adi,adxl345" or "adi,adxl346" value first. This prevents the device
node from being matched with the adxl34x driver.
Fix this by adding an OF match table with an "adi,adxl345" compatible
entry. There's no need to add the "adi,adxl346" entry as the ADXL346 is
backward-compatible with the ADXL345 with differences handled by runtime
detection of the device model.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
As the name suggests, always_unused argument in cyapa_gen3_set_power_mode()
is never used, so there is no reason for setting it to 0.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Joydev is currently thinking some absolute mice are joystick, and that
messes up games in VMware guests, as the cursor typically gets stuck in
the top left corner.
Try to detect the event signature of a VMmouse input device and back off
for such devices. We're still incorrectly detecting, for example, the
VMware absolute USB mouse as a joystick, but adding an event signature
matching also that device would be considerably more risky, so defer that
to a later merge window.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This makes the intent a tad more clear.
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The vmmouse Kconfig help text was referring to an incorrect user-space
driver version. Fix this.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On v7 touchpads sometimes when 2 fingers are moved down on the touchpad
until they "fall of" the touchpad, the second touch will report 0 for y
(max y really since the y axis is inverted) and max x as coordinates,
rather then reporting 0, 0 as is expected for a non touching finger.
This commit detects this and treats these touches as non touching.
See the evemu-recording here:
https://bugzilla.redhat.com/attachment.cgi?id=1025058
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1221200
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Now that the generic process_bitmap function has been improved to offer
accurate coordinates for the first touch we can use it for v5 (dolphin)
touchpads too.
Besides being a nice code cleanup this also fixes the saw tooth pattern
in the coordinates for the second touch the dolphin specific version had.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Rename alps_set_abs_params_mt to alps_set_abs_params_semi_mt,
to make it clear that it is only (to be) used for semi-mt devices.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
With the recent process_bitmap() changes all semi-mt devices always report
the first finger down in slot 0, so stop using input-mt finger tracking
for these.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
All alps semi-mt touchpads give us the following data when 2 (or more)
fingers are touching: 1 more or less accurate touch for the first finger
down, and a bitmap with columns and rows in which 1 or more fingers are
seen resulting in a crude (low res) bounding box.
So far for v3, rushmore and v4 touchpads we've been reporting the
coordinates of 2 opposite corners of the box when 2 fingers are touching.
Ignoring the much better resolution data given in the normal position
packet.
This commit actually uses this data for the first touch, figures out which
corner of the bounding box is closest to the first touch, and reports the
coordinates of the opposite corner for the second touch, resulting in
much better data for the first touch and for the single touch
pointer-emulation events.
This approach is similar to the one in alps_process_bitmap_dolphin, that
function takes the single accurate touch info, calculates the distance to
the center of the bounding box, and then puts the 2nd touch mirrored to
the center. The downside of that approach is that if both touches move
slowly in the same direction, the bounding box will stay the same for a
while (as it is low res) and the second touch will thus been seen moving
in the opposite direction until the bounding box actually changes, and
then the second touch snaps to its new position resulting in a saw tooth
pattern in the coordinates for the second touch, hence this new approach.
This commit fixes 2 finger scrolling being choppy / jumpy on these
touchpads.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We should decode the position packet before the packet with the bitmap
data. This way we can use the more accurate position info in
process_bitmap() to get better results.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pinnacle / Rushmore packets contain either position info, or bitmap info,
never both. So far we've in essence been storing garbage in the position /
bitmap fields of the fields struct when decoding a bitmap / pos packet.
We've been relying on the following sequence to get away with this:
1) Decode bitmap packet
2) Process bitmap packet
3) Decode position packet
4) Use position / button info
This patch allows us to change this sequence, which will allow using the
position info when processing the bitmap for more accurate results.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Change alps_decode_rushmore to do all decoding itself, rather then relying
on alps_decode_pinnacle and then overriding some fields + or-ing in some
bits.
This is a preparation patch for modifying the decode functions to properly
differentiate between position and bitmap packets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since commit 1c6c69525b ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since commit 1c6c69525b ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since commit 1c6c69525b ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since commit 1c6c69525b ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
max7359_build_keycode() does the same thing as matrix_keypad_build_keymap(),
but the latter can also handle DT bindings.
Tested on beagleboard-xm.
Signed-off-by: Evgeniy A. Dushistov <dushistov@mail.ru>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In datasheet of max7359 there is the following description of this flag:
0 - INT cleared when FIFO empty,
1 - INT cleared after host read. In this mode, I2C should read
FIFO until interrupt condition removed, or further INT may be lost.
So, if we set this flag, we have to read FIFO until it becomes empty. But
in interrupt we read FIFO just once. This lead to "keyboard" hang until
reboot, if we press several keys, because of interrupt handler read just
one "press" from FIFO and clear interrupt.
Signed-off-by: Evgeniy A. Dushistov <dushistov@mail.ru>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When the v3 hardware sees more than one finger, it uses the semi-mt
protocol to report the touches. However, it currently works when
num_fingers is 0, 1 or 2, but when it is 3 and above, it sends only 1
finger as if num_fingers was 1.
This confuses userspace which knows how to deal with extra fingers
when all the slots are used, but not when some are missing.
Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=90101
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We have been testing wrong variable when trying to make sure that input
allocation succeeded.
Reported by Coverity (CID 1295918).
Acked-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add the TI drv2665 piezo haptic driver. This haptics IC requires the data
to be streamed to the FIFO for continuous output.
Datasheet can be found at:
http://www.ti.com/product/drv2665
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fix the Kconfig for the drv2667 as there was a copy/paste error.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Wait a little bit longer, 50mS instead of 20mS, until the driver starts
polling for pen-up. The problematic behavior before this patch is applied
is as follows. The behavior was observed on the STMPE610QTR controller.
Upon a physical pen-down event, the touchscreen reports one set of x-y-p
coordinates and a pen-down event. After that, the pen-up polling is
triggered and since the controller is not ready yet, the polling mistakenly
detects a pen-up event while the physical state is still such that the pen
is down on the touch surface.
The pen-up handling flushes the controller FIFO, so after that, all the
samples in the controller are discarded. The controller becomes ready
shortly after this bogus pen-up handling and does generate again a pen-down
interrupt. This time, the controller contains x-y-p samples which all read
as zero. Since pressure value is zero, this set of samples is effectively
ignored by userland.
In the end, the driver just bounces between pen-down and bogus pen-up
handling, generating no useful results. Fix this by giving the controller a
bit more time before polling it for pen-up.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use msecs_to_jiffies(20) instead of plain (HZ / 50), as the former is much
more explicit about it's behavior. We want to schedule the task 20 mS from
now, so make it explicit in the code.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The MSB of the first byte read via I2C at the coordinates address
indicates whether the data is valid or ready (called "buffer status" in
the datasheets) when an interrupt is raised. Previously, this bit was
ignored, which resulted in a lot of incorrect detections of "finger
removed" events.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The event mask was specified as 0xF (4 bits) when in reality is 0x1F (5
bits) in order to be capable of representing all FIFO length values from
0 to 16.
This caused a problem: when the keypad reported 16 pending events the
driver took it as 0, and did nothing. This in turn caused the keypad to
re-issue the interrupt over and over again.
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The pull mask is created by looping each row (column) and building an
8-bit integer with the configuration. It is written byte-by-byte, when
we reach the end of the rows (columns) or we're at the 3rd line (which
finishes the first byte, since each pin is 2bits on the mask).
However, this only works if we have at most 8 pins (2 bytes), which is
not the case for the ADP5589. So, write the byte at each boundary (every
4 rows/columns).
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
tty_name no longer uses the buf parameter, so remove it along with all
the 64 byte stack buffers that used to be passed in.
Mostly generated by the coccinelle script
@depends on patch@
identifier buf;
constant C;
expression tty;
@@
- char buf[C];
<+...
- tty_name(tty, buf)
+ tty_name(tty)
...+>
allmodconfig compiles, so I'm fairly confident the stack buffers
weren't used for other purposes as well.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's a set of updates to the Chrome OS platform drivers for this merge window.
Main new things this cycle is:
- Driver changes to expose the lightbar to users. With this, you can make your
own blinkenlights on Chromebook Pixels.
- Changes in the way that the atmel_mxt trackpads are probed. The laptop driver
is trying to be smart and not instantiate the devices that don't answer to
probe. For the trackpad that can come up in two modes (bootloader or regular),
this gets complicated since the driver already knows how to handle the two
modes including the actual addresses used. So now the laptop driver needs to
know more too, instantiating the regular address even if the bootloader one
is the probe that passed.
- mfd driver improvements by Javier Martines Canillas, and a few bugfixes
from him, kbuild and myself.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=NVa4
-----END PGP SIGNATURE-----
Merge tag 'chrome-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform
Pull chrome platform updates from Olof Johansson:
"Here's a set of updates to the Chrome OS platform drivers for this
merge window.
Main new things this cycle is:
- Driver changes to expose the lightbar to users. With this, you can
make your own blinkenlights on Chromebook Pixels.
- Changes in the way that the atmel_mxt trackpads are probed. The
laptop driver is trying to be smart and not instantiate the devices
that don't answer to probe. For the trackpad that can come up in
two modes (bootloader or regular), this gets complicated since the
driver already knows how to handle the two modes including the
actual addresses used. So now the laptop driver needs to know more
too, instantiating the regular address even if the bootloader one
is the probe that passed.
- mfd driver improvements by Javier Martines Canillas, and a few
bugfixes from him, kbuild and myself"
* tag 'chrome-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform:
platform/chrome: chromeos_laptop - instantiate Atmel at primary address
platform/chrome: cros_ec_lpc - Depend on X86 || COMPILE_TEST
platform/chrome: cros_ec_lpc - Include linux/io.h header file
platform/chrome: fix platform_no_drv_owner.cocci warnings
platform/chrome: cros_ec_lightbar - fix duplicate const warning
platform/chrome: cros_ec_dev - fix Unknown escape '%' warning
platform/chrome: Expose Chrome OS Lightbar to users
platform/chrome: Create sysfs attributes for the ChromeOS EC
mfd: cros_ec: Instantiate ChromeOS EC character device
platform/chrome: Add Chrome OS EC userspace device interface
platform/chrome: Add cros_ec_lpc driver for x86 devices
mfd: cros_ec: Add char dev and virtual dev pointers
mfd: cros_ec: Use fixed size arrays to transfer data with the EC
Pull more input subsystem updates from Dmitry Torokhov:
- an update to Atmel MXT driver that makes it functional on Google
Pixel 2 boxes (both touchpad and touchscreen)
- a new VMware VMMouse driver that should allow us drop X vmmouse
driver that requires root privileges (since it accesses ioports)
- XBox One controllers now support force feedback (rumble)
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: lm8333 - fix broken email address
Input: cyapa - fix setting suspend scan rate
Input: elan_i2c - fix calculating number of x and y traces.
Input: elan_i2c - report hovering contacts
Input: elants_i2c - zero-extend hardware ID in firmware name
Input: alps - document separate pointstick button bits for V2 devices
Input: atmel_mxt_ts - add support for Google Pixel 2
Input: xpad - add rumble support for Xbox One controller
Input: ff-core - use new debug macros
Input: add vmmouse driver
Input: elan_i2c - adjust for newer firmware pressure reporting
* 'drm-next-merged' of git://people.freedesktop.org/~airlied/linux: (9717 commits)
media-bus: Fixup RGB444_1X12, RGB565_1X16, and YUV8_1X24 media bus format
hexdump: avoid warning in test function
fs: take i_mutex during prepare_binprm for set[ug]id executables
smp: Fix error case handling in smp_call_function_*()
iommu-common: Fix PARISC compile-time warnings
sparc: Make LDC use common iommu poll management functions
sparc: Make sparc64 use scalable lib/iommu-common.c functions
Break up monolithic iommu table/lock into finer graularity pools and lock
sparc: Revert generic IOMMU allocator.
tools/power turbostat: correct dumped pkg-cstate-limit value
tools/power turbostat: calculate TSC frequency from CPUID(0x15) on SKL
tools/power turbostat: correct DRAM RAPL units on recent Xeon processors
tools/power turbostat: Initial Skylake support
tools/power turbostat: Use $(CURDIR) instead of $(PWD) and add support for O= option in Makefile
tools/power turbostat: modprobe msr, if needed
tools/power turbostat: dump MSR_TURBO_RATIO_LIMIT2
tools/power turbostat: use new MSR_TURBO_RATIO_LIMIT names
Bluetooth: hidp: Fix regression with older userspace and flags validation
config: Enable NEED_DMA_MAP_STATE by default when SWIOTLB is selected
perf/x86/intel/pt: Fix and clean up error handling in pt_event_add()
...
That solves several merge conflicts:
Documentation/DocBook/media/v4l/subdev-formats.xml
Documentation/devicetree/bindings/vendor-prefixes.txt
drivers/staging/media/mn88473/mn88473.c
include/linux/kconfig.h
include/uapi/linux/media-bus-format.h
The ones at subdev-formats.xml and media-bus-format.h are not trivial.
That's why we opted to merge from DRM.
My Pengutronix address is not valid anymore, redirect people to the
Pengutronix kernel team.
Reported-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The suspend scan rate value should not exceed 1000, unfortunately when
implementing the limit we used max_t instead of min_t, causing the value to
be at least 1000.
Signed-off-by: Dudley Du <dudl@cypress.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
According to Elan's firmware engineers we should not be subtracting 1 form
the raw number of x and y traces so that the pitch size is correct. For
example, if the touchpad x resolution is 2800 and x trace number is 20,
the pitch size of x should be 2800/20 = 140, not 2800/19 = 147.36.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When hover is detected report ABS_MT_DISTANCE as 1; for active contacts
the distance is reported as 0.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's zero-extend hardware id number when forming firmware file name,
to avoid kernel requesting firmware like "elants_i2c_ 0.bin", which
is quite unexpected.
Acked-by: Charlie Mooney<charliemooney@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
cycle:
- A new GPIO hogging mechanism has been added. This can
be used on boards that want to drive some GPIO line high,
low, or set it as input on boot and then never touch it
again. For some embedded systems this is bliss and
simplifies things to a great extent.
- Some API cleanup and closure: gpiod_get_array() and
gpiod_put_array() has been added to get and put GPIOs
in bulk as was possible with the non-descriptor API.
- Encapsulate cross-calls to the pin control subsystem in
<linux/gpio/driver.h>. Now this should be the only header
any GPIO driver needs to include or something is wrong.
Cleanups restricting drivers to this include are welcomed
if tested.
- Sort the GPIO Kconfig and split it into submenus, as
it was becoming and unstructured, illogical and
unnavigatable mess. I hope this is easier to follow.
Menus that require a certain subsystem like I2C can
now be hidden nicely for example, still working on
others.
- New drivers:
- New driver for the Altera Soft GPIO.
- The F7188x driver now handles the F71869 and
F71869A variants.
- The MIPS Loongson driver has been moved to
drivers/gpio for consolidation and cleanup.
- Cleanups:
- The MAX732x is converted to use the GPIOLIB_IRQCHIP
infrastructure.
- The PCF857x is converted to use the GPIOLIB_IRQCHIP
infrastructure.
- Radical cleanup of the OMAP driver.
- Misc:
- Enable the DWAPB GPIO for all architectures. This is
a "hard IP" block from Synopsys which has started to
turn up in so diverse architectures as X86 Quark, ARC
and a slew of ARM systems. So even though it's not an
expander, it's generic enough to be available for all.
- We add a mock GPIO on Crystalcove PMIC after a long
discussion with Daniel Vetter et al, tracing back to
the shootout at the kernel summit where DRM drivers
and sub-componentization was discussed. In this case
a mock GPIO is assumed to be the best compromise
gaining some reuse of infrastructure without making
DRM drivers overly complex at the same time. Let's
see.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=QFbC
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.1 development cycle:
- A new GPIO hogging mechanism has been added. This can be used on
boards that want to drive some GPIO line high, low, or set it as
input on boot and then never touch it again. For some embedded
systems this is bliss and simplifies things to a great extent.
- Some API cleanup and closure: gpiod_get_array() and
gpiod_put_array() has been added to get and put GPIOs in bulk as
was possible with the non-descriptor API.
- Encapsulate cross-calls to the pin control subsystem in
<linux/gpio/driver.h>. Now this should be the only header any GPIO
driver needs to include or something is wrong. Cleanups
restricting drivers to this include are welcomed if tested.
- Sort the GPIO Kconfig and split it into submenus, as it was
becoming and unstructured, illogical and unnavigatable mess. I
hope this is easier to follow. Menus that require a certain
subsystem like I2C can now be hidden nicely for example, still
working on others.
- New drivers:
- New driver for the Altera Soft GPIO.
- The F7188x driver now handles the F71869 and F71869A variants.
- The MIPS Loongson driver has been moved to drivers/gpio for
consolidation and cleanup.
- Cleanups:
- The MAX732x is converted to use the GPIOLIB_IRQCHIP
infrastructure.
- The PCF857x is converted to use the GPIOLIB_IRQCHIP
infrastructure.
- Radical cleanup of the OMAP driver.
- Misc:
- Enable the DWAPB GPIO for all architectures. This is a "hard
IP" block from Synopsys which has started to turn up in so
diverse architectures as X86 Quark, ARC and a slew of ARM
systems. So even though it's not an expander, it's generic
enough to be available for all.
- We add a mock GPIO on Crystalcove PMIC after a long discussion
with Daniel Vetter et al, tracing back to the shootout at the
kernel summit where DRM drivers and sub-componentization was
discussed. In this case a mock GPIO is assumed to be the best
compromise gaining some reuse of infrastructure without making
DRM drivers overly complex at the same time. Let's see"
* tag 'gpio-v4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (62 commits)
Revert "gpio: sch: use uapi/linux/pci_ids.h directly"
gpio: dwapb: remove dependencies
gpio: dwapb: enable for ARC
gpio: removing kfree remove functionality
gpio: mvebu: Fix mask/unmask managment per irq chip type
gpio: split GPIO drivers in submenus
gpio: move MFD GPIO drivers under their own comment
gpio: move BCM Kona Kconfig option
gpio: arrange SPI Kconfig symbols alphabetically
gpio: arrange PCI GPIO controllers alphabetically
gpio: arrange I2C Kconfig symbols alphabetically
gpio: arrange Kconfig symbols alphabetically
gpio: ich: Implement get_direction function
gpio: use (!foo) instead of (foo == NULL)
gpio: arizona: drop owner assignment from platform_drivers
gpio: max7300: remove 'ret' variable
gpio: use devm_kzalloc
gpio: sch: use uapi/linux/pci_ids.h directly
gpio: x-gene: fix devm_ioremap_resource() check
gpio: loongson: Add Loongson-3A/3B GPIO driver support
...
This change allows atmel_mxt_ts to bind to ACPI-enumerated devices in
Google Pixel 2 (2015).
While newer version of ACPI standard allow use of device-tree-like
properties in device descriptions, the version of ACPI implemented in
Google BIOS does not support them, and we have to resort to DMI data to
specify exact characteristics of the devices (touchpad vs. touchscreen,
GPIO to button mapping, etc).
Pixel 1 continues to use i2c devices and platform data created by
chromeos-laptop driver, since ACPI does not enumerate them.
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input subsystem updates from Dmitry Torokhov:
"You will get the following new drivers:
- Qualcomm PM8941 power key drver
- ChipOne icn8318 touchscreen controller driver
- Broadcom iProc touchscreen and keypad drivers
- Semtech SX8654 I2C touchscreen controller driver
ALPS driver now supports newer SS4 devices; Elantech got a fix that
should make it work on some ASUS laptops; and a slew of other
enhancements and random fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (51 commits)
Input: alps - non interleaved V2 dualpoint has separate stick button bits
Input: alps - fix touchpad buttons getting stuck when used with trackpoint
Input: atkbd - document "no new force-release quirks" policy
Input: ALPS - make alps_get_pkt_id_ss4_v2() and others static
Input: ALPS - V7 devices can report 5-finger taps
Input: ALPS - add support for SS4 touchpad devices
Input: ALPS - refactor alps_set_abs_params_mt()
Input: elantech - fix absolute mode setting on some ASUS laptops
Input: atmel_mxt_ts - split out touchpad initialisation logic
Input: atmel_mxt_ts - implement support for T100 touch object
Input: cros_ec_keyb - fix clearing keyboard state on wakeup
Input: gscps2 - drop pci_ids dependency
Input: synaptics - allocate 3 slots to keep stability in image sensors
Input: Revert "Revert "synaptics - use dmax in input_mt_assign_slots""
Input: MT - make slot assignment work for overcovered solutions
mfd: tc3589x: enforce device-tree only mode
Input: tc3589x - localize platform data
Input: tsc2007 - Convert msecs to jiffies only once
Input: edt-ft5x06 - remove EV_SYN event report
Input: edt-ft5x06 - allow to setting the maximum axes value through the DT
...
This adds rumble support for Xbox One controller by sending continuous
rumble command. Trigger button rumbling is not yet implemented.
Signed-off-by: Ming-ting Yao Wei <mwei@lxde.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
VMMouse enables low-latency mouse-cursor-movements for VMWare and QEMU
guests. By removing the guest cursor and using the host as a guest cursor
the cursor movement appears instant although in reality there is some lag.
To be able to do this, the host's view of the cursor position must exactly
match the guest's view and an absolute pointer device is needed. Enter the
VMMouse. While the VMMouse driver has historically been an Xorg user-space
driver, implementing it as a kernel imput driver enables rootless Xorg and
new compositing display servers for VMware guests.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Get pressure format flag from firmware to check if we need to normalize
pressure data before reporting it.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull HID updates from Jiri Kosina:
- quite a few firmware fixes for RMI driver by Andrew Duggan
- huion and uclogic drivers have been substantially overlaping in
functionality laterly. This redundancy is fixed by hid-huion driver
being merged into hid-uclogic; work done by Benjamin Tissoires and
Nikolai Kondrashov
- i2c-hid now supports ACPI GPIO interrupts; patch from Mika Westerberg
- Some of the quirks, that got separated into individual drivers, have
historically had EXPERT dependency. As HID subsystem matured (as
well as the individual drivers), this made less and less sense. This
dependency is now being removed by patch from Jean Delvare
- Logitech lg4ff driver received a couple of improvements for mode
switching, by Michal Malý
- multitouch driver now supports clickpads, patches by Benjamin
Tissoires and Seth Forshee
- hid-sensor framework received a substantial update; namely support
for Custom and Generic pages is being added; work done by Srinivas
Pandruvada
- wacom driver received substantial update; it now supports
i2c-conntected devices (Mika Westerberg), Bamboo PADs are now
properly supported (Benjamin Tissoires), much improved battery
reporting (Jason Gerecke) and pen proximity cleanups (Ping Cheng)
- small assorted fixes and device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (68 commits)
HID: sensor: Update document for custom sensor
HID: sensor: Custom and Generic sensor support
HID: debug: fix error handling in hid_debug_events_read()
Input - mt: Fix input_mt_get_slot_by_key
HID: logitech-hidpp: fix error return code
HID: wacom: Add support for Cintiq 13HD Touch
HID: logitech-hidpp: add a module parameter to keep firmware gestures
HID: usbhid: yet another mouse with ALWAYS_POLL
HID: usbhid: more mice with ALWAYS_POLL
HID: wacom: set stylus_in_proximity before checking touch_down
HID: wacom: use wacom_wac_finger_count_touches to set touch_down
HID: wacom: remove hardcoded WACOM_QUIRK_MULTI_INPUT
HID: pidff: effect can't be NULL
HID: add quirk for PIXART OEM mouse used by HP
HID: add HP OEM mouse to quirk ALWAYS_POLL
HID: wacom: ask for a in-prox report when it was missed
HID: hid-sensor-hub: Fix sparse warning
HID: hid-sensor-hub: fix attribute read for logical usage id
HID: plantronics: fix Kconfig default
HID: pidff: support more than one concurrent effect
...
Non interleaved V2 dualpoint touchpad / stick combos have separate stick
button bits in the touchpad packets, if we do not check these then the
trackpoint buttons will not work when using the touchpad, and when pressed
when the user starts using the touchpad will report a release event even
though the button is still pressed.
This commit fixes this by checking the separate bits, note that we simply
combine the buttons, since the hardware does the same when using the touchpad
buttons with the trackpoint, so we do not have enough information to properly
separate them.
Reported-by: Hans de Bruin <jmdebruin@xmsnet.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When the left touchpad button gets pressed, and then the trackpoint is
moved, and then the button is released, the following happens:
1) touchpad packet is received, touchpad evdev node reports BTN_LEFT 1
2) pointing stick packet is received, the hw will report a BTN_LEFT 1 in
this packet because when the trackstick is active it communicates the
combined touchpad + pointing stick buttons in the trackstick packet,
since alps_report_bare_ps2_packet passes NULL (*) for the dev2 parameter
to alps_report_buttons the combining is not detected and the
pointing stick evdev node will also report BTN_LEFT 1
3) on release of the button a pointing stick packet with BTN_LEFT 0 is
received and the pointing stick evdev node will report BTN_LEFT 0
Note how because of the passing as NULL for dev2 the touchpad evdev node
will never send BTN_LEFT 0 in this scenario leading to a stuck mouse button.
This is a regression in 4.0 introduced by commit 04aae283ba
("Input: ALPS - do not mix trackstick and external PS/2 mouse data")
This commit fixes this by passing in the touchpad evdev as dev2 parameter
when calling alps_report_buttons for the pointingstick on alps v2 devices,
so that alps_report_buttons correctly detect that we're already reporting
the button as pressed via the touchpad evdev node, and will also send the
release event there.
Cc: stable@vger.kernel.org # 4.0
Reported-by: Hans de Bruin <jmdebruin@xmsnet.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
To save people some time let's document that we do not want new quirks for
"force-release" keys in the kernel and that they should patch userspace
(udev) instead.
Suggested-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch fixes a kernel panic which occurs when buf_list is empty. This can
happen occasionally when user space is under heavy load (e.g. due to image
processing on the CPU) and new buffers aren't re-queued fast enough. In that
case, vb2_start_streaming_called can return true, but when the spinlock
is taken and sur40_poll attempts to fetch the next buffer from buf_list, the
list is in fact empty.
This patch needs to be applied on top of the queued one adding V4L2 support
to the sur40 driver.
Signed-off-by: Florian Echtler <floe@butterbrot.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Masaki Ota <masaki.ota@jp.alps.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This change adds support for SS4 touchpad devices as ALPS_PROTO_V8
protocol. They are real multi-touch devices and can be found in TOSHIBA
Tecra C50.
Signed-off-by: Masaki Ota <masaki.ota@jp.alps.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In preparation for adding support for SS4 touchpads, let's split
alps_set_abs_params_mt into common, v7-specific, and other protocols
portions.
Signed-off-by: Masaki Ota <masaki.ota@jp.alps.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVIws/AAoJEHm+PkMAQRiGwEcH/1GCBqrBzXaKwDdCPMRcYVUb
MYkXmGkCGRYWe5MXI8QNAaa/CdG6mAFMHWN6CaMMpLTxnM1m87uBg01fQMsh73BO
mRVLKE/soiJDnR1gYzBBDBYV/AUvytN5PhgeNaA95YIJvU3T1f3iTnV8vs30Dp0L
YpxSqwr3C0k7C9IE0VcgfzvWJPCnQ9IWHuX3jn5s1XjGKVNbBYHMt6FusHdyXMfT
dp8ksuGHwm30mTFI5xJpKOrRzfi+P5EsEUrsnFRPRM/iFTVrM5R7eaUhsRZb2+Wo
YApnbYhUYz7om1AuQ+UZ/+S6y7ZLlGWegI1lWI754GIsczG5vPHEYhhgkzMhTsc=
=kR1V
-----END PGP SIGNATURE-----
Merge tag 'v4.0-rc7' into next
Sync up with Linux 4.0-rc7 to bring in ALPS changes.
The case occurred recently with a touchscreen using twice a slot during a
single EV_SYN event:
E: 0.288415 0000 0000 0000 # ------------ SYN_REPORT (0) ----------
E: 0.296207 0003 002f 0000 # EV_ABS / ABS_MT_SLOT 0
E: 0.296207 0003 0039 -001 # EV_ABS / ABS_MT_TRACKING_ID -1
E: 0.296207 0003 002f 0001 # EV_ABS / ABS_MT_SLOT 1
E: 0.296207 0003 0035 0908 # EV_ABS / ABS_MT_POSITION_X 908
E: 0.296207 0003 0036 1062 # EV_ABS / ABS_MT_POSITION_Y 1062
E: 0.296207 0003 002f 0000 # EV_ABS / ABS_MT_SLOT 0
E: 0.296207 0003 0039 8787 # EV_ABS / ABS_MT_TRACKING_ID 8787
E: 0.296207 0003 0035 1566 # EV_ABS / ABS_MT_POSITION_X 1566
E: 0.296207 0003 0036 0861 # EV_ABS / ABS_MT_POSITION_Y 861
E: 0.296207 0003 0000 0908 # EV_ABS / ABS_X 908
E: 0.296207 0003 0001 1062 # EV_ABS / ABS_Y 1062
E: 0.296207 0000 0000 0000 # ------------ SYN_REPORT (0) ----------
This occurred because while having already slots 0 and 1 assigned, the
touchscreen sent:
0.293377 Tip Switch: 0 | Contact Id: 0 | X: 539 | Y: 1960 | Contact Count: 3
0.294783 Tip Switch: 1 | Contact Id: 1 | X: 908 | Y: 1062 | Contact Count: 0
0.296187 Tip Switch: 1 | Contact Id: 2 | X: 1566 | Y: 861 | Contact Count: 0
Slot 0 is released correclty, but when we look for Contact ID 2, the slot
0 is then picked up again because it is marked as inactive (trackingID < 0).
This is wrong, and we should not reuse a slot in the same frame.
The test should also check for input_mt_is_used().
In addition, we need to initialize mt->frame to an other value than 0.
With mt->frame being 0, all slots are tags as currently used, and so
input_mt_get_slot_by_key() would return -1 for all requests.
Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=88903
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
On ASUS TP500LN and X750JN, the touchpad absolute mode is reset each
time set_rate is done.
In order to fix this, we will verify the firmware version, and if it
matches the one in those laptops, the set_rate function is overloaded
with a function elantech_set_rate_restore_reg_07 that performs the
set_rate with the original function, followed by a restore of reg_07
(the register that sets the absolute mode on elantech v4 hardware).
Also the ASUS TP500LN and X750JN firmware version, capabilities, and
button constellation is added to elantech.c
Cc: stable@vger.kernel.org
Reported-and-tested-by: George Moutsopoulos <gmoutso@yahoo.co.uk>
Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
"Updates for the input subsystem - two more tweaks for ALPS driver to
work out kinks after splitting the touchpad, trackstick, and potential
external PS/2 mouse into separate input devices.
Changes to support ALPS SS4 devices (protocol V8) will be coming in
4.1..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: alps - document stick behavior for protocol V2
Input: alps - report V2 Dualpoint Stick events via the right evdev node
Input: alps - report interleaved bare PS/2 packets via dev3
If the "linux,gpio-keymap" DT property is defined, the T19 keys are
configured and the device is setup as a touchpad rather than a touchscreen.
The logic is part of the input device initialization routine but it can be
factored out to its own function to simplify the former.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support for the new T100 object which replaces the previous T9
multitouch touchscreen object in recent maXTouch devices. T100 provides
improved reporting with selectable auxiliary information, and a type field
for hover/stylus/glove reporting.
The hovering finger support was based on Chung-Yih's work in the ChromiumOS
downstream kernel:
https://chromium-review.googlesource.com/#/c/219280/
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Yufeng Shen <miletus@chromium.org>
[javier: Factor out T9 and T100 init functions and rework hover support]
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
As the comment right before explains, the keyboard state is to be cleared
only if the EC wasn't a wakeup source in the last suspend.
Without this commit, there's an unneeded delay when resuming from suspend
and we also lose the key that was pressed while suspended.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This driver does not use any PCI IDs, don't include the pci_ids.h header.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When slowly dropping 1, 2 and then 3 fingers on an image sensor touchpad,
we can see that the first finger gets reassigned a new slot while it did
not move. This is due to the kernel tracking algorithm which can not assign
correctly the 3 touches, being out of slots.
Declaring that we support 3 slots allows to actually forward:
slot 0 -> down, slot 1 -> up, slot 2 -> down
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Henrik Rydberg <rydberg@bitmath.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This reverts commit 09d042a2eb ("Revert "Input: synaptics - use dmax in
input_mt_assign_slots"")
Now that balanced slots assignments seem to be fixed, let's re-enable the
use in synaptics.c and wait for users to complain if there are still
problems.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Henrik Rydberg <rydberg@bitmath.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The recent inclusion of a deassignment cost in the slot assignment
algorithm did not properly account for the corner cases where the
solutions are overcovered. This change makes sure the resulting
assignment is unique, allocating new slots when necessary.
Signed-off-by: Henrik Rydberg <rydberg@bitmath.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On V2 devices the DualPoint Stick reports bare packets, these should be
reported via the "AlpsPS/2 ALPS DualPoint Stick" dev2 evdev node, which also
has the INPUT_PROP_POINTING_STICK propbit set.
Note that since there is no way to distinguish these packets from an external
PS/2 mouse (insofar as these laptops have an external PS/2 port) this means
that we will be reporting PS/2 mouse events via this evdev node too, as we've
been doing in kernel 3.19 and older.
This has been tested on a Dell Latitude D620 and a Dell Latitude E6400,
which both have a V2 touchpad + a DualPoint Stick which reports bare packets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Bare packets should be reported via the same evdev device independent on
whether they are detected on the beginning of a packet or in the middle
of a packet.
This has been tested on a Dell Latitude E6400, where the DualPoint Stick
reports bare packets, which get reported via dev3 when the touchpad is
idle, and via dev2 when the touchpad and stick are used simultaneously.
This commit fixes this inconsistency by always reporting bare packets via
dev3. Note that since the come from a DualPoint Stick they really should be
reported via dev2, this gets fixed in a later commit.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
All systems using the TC3589x multifunction expander uses
devicetree, so don't clutter the place with a lot of
and assume it is there.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This driver can only get its platform data from the device tree, and all
platforms using it do that. Localize the platform data for the keypad. A
later patch will enforce the device tree / OF dependence.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input subsystem fixes from Dmitry Torokhov:
"A fix for ALPS driver for issue introduced in the latest update and a
tweak for yet another Lenovo box in Synaptics.
There will be more ALPS tweaks coming.."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: define INPUT_PROP_ACCELEROMETER behavior
Input: synaptics - fix min-max quirk value for E440
Input: synaptics - add quirk for Thinkpad E440
Input: ALPS - fix max coordinates for v5 and v7 protocols
Input: add MT_TOOL_PALM
This patch adds raw video support for the Samsung SUR40 using vbuf2-dma-sg.
All tests from v4l2-compliance pass. Support for VB2_USERPTR is currently
disabled due to unexpected interference with dma-sg buffer sizes.
Signed-off-by: Florian Echtler <floe@butterbrot.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: fix compile warning: %ld -> %zd]
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit 98dc070373 ("Input: synaptics - add quirk for Thinkpad E440") had
a typo in ymax, this changes the value to the one reported by
touchpad-edge-detector and mentioned in the commit.
Signed-off-by: Filip Ayazi <filipayazi@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Eliminate redundant calculations by performing millisecond to jiffy
calculations once during driver initialization.
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
All systems using the TC3589x multifunction expander uses
devicetree, so don't clutter the place with a lot of
and assume it is there.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
input_register_device already sets the EV_SYN event since all devices can
generate them.
Remove the redundant affectation.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Currently the driver relies on some obscure and undocumented register to set
the maximum axis value.
The reported value is way too high to be meaningful, which confuses some
userspace tools like QT's evdevtouch plugin which try to scale the reported
events to the maximum values.
Use the values from the DT to set meaningful values.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
So far, the DT parsing code was only setting up the regular input axes,
completely ignoring their multitouch counter parts.
Fill them with the same parameters than the regular axes.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The DT parsing function currently duplicates a lot of the code to parse the
touchscreen DT properties. In order to ease further additions to this
parsing routine, rework it slightly to create new helper functions.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This simplifies error handling and device removal code. Also let's
get rid of setting driver's owner since i2c core does it for us.
Tested-by: Stefan Sauer <ensonic@google.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The ChipOne icn8318 is an i2c capacitive touchscreen controller typically
used in cheap android tablets, this commit adds a driver for it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds support for another model of IRTOUCH SYSTEMS Co.,LtD infrared
touchscreens. The USB vendorID/deviceID is 6615/0012. It is also sold
under the label "Elektrosil".
The datasheet states that coordinates for x and y are in the range from
0 to 32767.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add initial version of the Broadcom touchscreen driver.
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Tested-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Jonathan Richardson <jonathar@broadcom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Its ClickPad shares PNP ID "LEN2006" with the one in model E540 which is
already handled by the driver (both are Haswell iterations of the Edge
line, launched in 2014) but the dimensions it reports are different:
$ sudo ./touchpad-edge-detector /dev/input/event3
Touchpad SynPS/2 Synaptics TouchPad on /dev/input/event3
Move one finger around the touchpad to detect the actual edges
Kernel says: x [1472..5044], y [1408..3398]
Touchpad sends: x [1024..5045], y [2457..4832] /^C
Fortunately we can use the board ID, which is also different, to
distinguish among them.
$ dmesg | grep -i synaptics
psmouse serio1: synaptics: Touchpad model: 1, fw: 8.1, id: 0x1e2b1,
caps: 0xd001a3/0x940300/0x127c00, board id: 2691, fw id: 1494646
psmouse serio1: synaptics: serio: Synaptics pass-through port at
isa0060/serio1/input0
input: SynPS/2 Synaptics TouchPad as
/devices/platform/i8042/serio1/input/input4
Board ID in E540 is 2722:
psmouse serio1: synaptics: Touchpad model: 1, fw: 8.1, id: 0x1e2b1,
caps: 0xd001a3/0x940300/0x127c00, board id: 2722, fw id: 1484859
(from https://launchpadlibrarian.net/179702965/BootDmesg.txt)
Signed-off-by: Ramiro Morales <cramm0@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVD1VGAAoJEHm+PkMAQRiG7yoH/juKOQ1zbxi5M+mleDEEJtA0
RxQSojqEMWIKrWi8PNZxjENn1OZB6XOLIXOhlyAZBrmgsjO34p1DyXlZMznr/R8W
kQ2Xxs061hRtB3OuruMIqOApUrjuqsaCwgbgUS1qWmqZcoyZN4oELyZMP6OOlqv5
UUBZm8MfyXGyxrCcg39mjct3VEOhiuEcvL6SUxOC380CdSVAnyqHFPcz0JVqMUn9
9RUBs0T9cMdhb0mZ2bfXzt6AKArj63G2nXOum+VzFcvspSm2U+MPIDCuoE+ZbTPS
jqIAgG0rj1ezRyb5oeJrvlU0Yy3u/cXoMPs9+kORvpladooYNLti8ovh6qllm0I=
=d/ye
-----END PGP SIGNATURE-----
Merge tag 'v4.0-rc5' into next
Merge with the latest upstream to synchronize Synaptics changes
and bring in new infrastructure pieces.
Conflicts:
drivers/input/mouse/synaptics.c
Commit 3296f71cd2 ("Input: ALPS - consolidate
setting protocol parameters") inadvertently moved call to
alps_dolphin_get_device_area() from v5 to v7 protocol, causing both
protocols report incorrect maximum values for X and Y axes which resulted
in crash in Synaptics X driver.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=94801
Reported-by: Santiago Gala <sgala@apache.org>
Reported-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This commit introduces two new optional device-tree properties:
"tp-sensitive-adjust": adjust sensitivity of pen down detection
"filter-type": select median and averaging filter
The previous fixed defaults, didn't work well for the Olimex
A13-LCD10TS (I have).
Signed-off-by: Jens Thiele <karme@karme.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This change fixes a style issue where spaces where used instead of tabs.
Signed-off-by: Brian K. Turner <turnerbk84@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
"An update to Synaptics driver that makes it usable with the 2015
lineup from Lenovo"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: synaptics - use dmax in input_mt_assign_slots"
Input: synaptics - remove X250 from the topbuttonpad list
Input: synaptics - remove X1 Carbon 3rd gen from the topbuttonpad list
Input: synaptics - re-route tracksticks buttons on the Lenovo 2015 series
Input: synaptics - remove TOPBUTTONPAD property for Lenovos 2015
Input: synaptics - retrieve the extended capabilities in query $10
Input: synaptics - do not retrieve the board id on old firmwares
Input: synaptics - handle spurious release of trackstick buttons
Input: synaptics - fix middle button on Lenovo 2015 products
Input: synaptics - skip quirks when post-2013 dimensions
Input: synaptics - support min/max board id in min_max_pnpid_table
Input: synaptics - remove obsolete min/max quirk for X240
Input: synaptics - query min dimensions for fw v8.1
Input: synaptics - log queried and quirked dimension values
Input: synaptics - split synaptics_resolution(), query first
of_device_id is always used as const argument (See driver.of_match_table
and open firmware functions).
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Calling pwm_config() with a period equal to zero always results in
error (-EINVAL) and pwm chip config method is never called.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The commit titled: "Input: sun4i-ts - A10 (sun4i) has a different
temperature curve" contains a math error, the offset it uses is in degrees,
but the actual code applies the offset before multiplying by stepsize :|
Given that this is rather backwards (every math course ever thought applies
the multiplication before the offset for linear functions), this commit
fixes things by changing the code applying the offset to do the logical
thing, adjusting the offset for the other models accordingly.
This has been tested on an A10, A13, A20 and A31 to make sure everything
really is correct now.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
"irqsrc" needs to be signed for the error handling to work.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Currently the elants_i2c driver simply requests a static filename
/lib/firmware/elants_i2c.bin when it gets firmware updates. This is a
problem if you have two Elan touchscreens using the same driver. If both
touchscreens have different firmwares, you would need to move the files
around in your filesystem when you're updating them so that they don't get
updated with the other's FW. If you have a read-only filesystem then this
is impossible, even.
This patch changes the elants_i2c driver to automatically append the
four-hex-digit hw_version of the device onto the name of the FW file it's
requesting for update. Since different touchscreens should have a
different hw_version's this means the user needs to append the hw version
of the touchscreen he or she intends to update onto the end of the firmware
filename and then the driver will do the rest.
The firmware filenames it looks for now are of the form:
elants_i2c_${HW_VERSION}.bin
eg:
elants_i2c_2a44.bin
Signed-off-by: Charlie Mooney <charliemooney@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
While registering serio device for i8042, mark them as wakeup-capable
and check their user space wakeup settings in i8042_pm_suspend() and
i8042_pm_resume() to enable or disable, respectively, their interrupts
to wake up the system.
This makes it possible to use the PC keyboard to wake up the system
from suspend-to-idle, among other things, after writing "enabled" to
the keyboard serio device's power/wakeup sysfs attribute.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Lenovo X250 has a PnpID of LEN0046, but it does not have the top software
button requirement.
For the record, Lenovo T450s and W541 have a PnpID of LEN200f and LEN004a,
so they are not on the top software button list.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Daniel Martin <consume.noise@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Lenovo decided to switch back to physical buttons for the trackstick on
their latest series. The PNPId list was provided before they reverted back
to physical buttons, so it contains the new models too. We can know from
the touchpad capabilities that the touchpad has physical buttons, so
removing the ids from the list is not mandatory. It is still nicer to
remove the wrong ids, so start by removing the X1 Carbon 3rd gen, with the
PNPId of LEN0048.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The 2015 series of the Lenovo thinkpads added back the hardware buttons on
top of the touchpad for the trackstick.
Unfortunately, they are wired to the touchpad, and not the trackstick.
Thus, they are seen as extra buttons from the kernel point of view.
This leads to a problem in user space because extra buttons on synaptics
devices used to be used as scroll up/down buttons. So in the end, the
experience for the user is scroll events for buttons left and right when
using the trackstick. Yay!
Fortunately, the firmware advertises such behavior in the extended
capability $10, and so we can re-route the buttons through the pass-through
interface.
Hallelujah-expressed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The 2015 series of the Lenovo thinkpads added back the hardware buttons on
top of the touchpad for the trackstick.
Unfortunately, Lenovo used the PNPIDs that are supposed to be "5 buttons"
touchpads, so the new laptops also have the INPUT_PROP_TOPBUTTONPAD. Yay!
Instead of manually removing each of the new ones, or hoping that we know
all the current ones, we can consider that the PNPIDs list that were given
contains touchpads that have the trackstick buttons, either physically
wired to them, or emulated with the top software button property.
Thanks to the extra buttons capability in query $10, we can reliably detect
the physical buttons from the software ones, and so we can remove the
TOPBUTTONPAD property even if it was declared as such.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Newer Synaptics touchpads need to get information from the query $10.
Retrieve it if available.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The board id capability has been added in firmware 7.5.
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Fimware 8.1 has a bug in which the extra buttons are only sent when the
ExtBit is 1. This should be fixed in a future FW update which should have
a bump of the minor version.
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On the X1 Carbon 3rd gen (with a 2015 broadwell cpu), the physical middle
button of the trackstick (attached to the touchpad serio device, of course)
seems to get lost.
Actually, the touchpads reports 3 extra buttons, which falls in the switch
below to the '2' case. Let's handle the case of odd numbers also, so that
the middle button finds its way back.
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Post-2013 Lenovo laptops provide correct min/max dimensions, which are
different with the ones currently quirked. According to
https://bugzilla.kernel.org/show_bug.cgi?id=91541 the following board ids
are assigned in the post-2013 touchpads:
t440p/t440s: LEN0036 -> 2964/2962
t540p: LEN0034 -> 2964
Using 2961 as the common minimum makes these 3 laptops OK. We may need
to update those values later if other pnp_ids has a lower board_id.
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add a min/max range for board ids to the min/max coordinates quirk. This
makes it possible to restrict quirks to specific models based upon their
board id. The define ANY_BOARD_ID (0) serves as a wild card.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=91541
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Martin <daniel.martin@secunet.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The firmware of the X240 (LEN0035, 2013/12) exposes the same values
x [1232..5710], y [1156..4696]
as the quirk applies.
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Martin <consume.noise@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Query the min dimensions even if the check
SYN_EXT_CAP_REQUESTS(priv->capabilities) >= 7 fails, but we know that the
firmware version 8.1 is safe.
With that we don't need quirks for post-2013 models anymore as they expose
correct min and max dimensions.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=91541
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Martin <consume.noise@gmail.com>
re-order the tests to check SYN_CAP_MIN_DIMENSIONS even on FW 8.1
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Logging the dimension values we queried and the values we use from a quirk
to overwrite can be helpful for debugging.
This partly relates to bug:
https://bugzilla.kernel.org/show_bug.cgi?id=91541
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Martin <consume.noise@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Split the function synaptics_resolution() into synaptics_resolution() and
synaptics_quirks(). synaptics_resolution() will be called before
synaptics_quirks() to query dimensions and resolutions before overwriting
them with quirks.
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Martin <consume.noise@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Testing has revealed that the temperature in the rtp controller of the A10
(sun4i) SoC has a different curve then on the A13 (sun5i) and later models.
Add a new sun5i-a13-ts compatible to differentiate the newer models and
set the curve based on the compatible string.
The new curve is still not ideal on all A10-s, that seems to have to
do with there being a large spread between different A10-s out there,
the new curve us based on callibration results on 4 completely different
models:
raw min raw max temp min temp max stepsize offset
Tong Zhang's hackberry 2402 2680 45.0 80.0 0.125 -255.3
Hansg's Cubieboard 2207 2300 36.0 45.0 0.096 -175.8
Olliver's lime 1 (*): 2258 2537 48.3 87.1 0.139 -265.7
Olliver's lime 2 (*): 2222 2486 46.7 91.7 0.170 -331.0
*) from: http://linux-sunxi.org/Temperature_Calibration
Average all 4: 0.133 -257.0
Average without outliers (middle 2): 0.132 -261.0
Since it is better to slightly overreport the temperature this patch uses
the average of all 4 as curve.
This fixes the temperature reported on the A10 being much higher then
expected.
Reported-by: Tong Zhang <lovewilliam@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Remove duplicate "repeat--" from function elan_initialize.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In order to better diagnose potential issues let's return error to the
upper layers when resuming the device fails and also add a few diagnostic
messages.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The device->pm pointer is always present so there is no need to do tricks with
conditionally defining the pointer.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Apparently, the threshold for large contact area seems to be rather low on
some devices, causing the touchpad to frequently freeze during normal
usage. Because we do now know how we are supposed to use the value in
question, this commit just drops the related code completely.
Signed-off-by: Mathias Gottschlag <mgottschlag@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
These PS/2 commands make some touchpads stop responding, so this commit
adds some dummy functions to replace the generic implementation. Because
scale changes were not encapsulated in a method of struct psmouse yet, this
commit adds a method set_scale to psmouse.
Signed-off-by: Mathias Gottschlag <mgottschlag@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We don't know whether x_max or y_max really hold the maximum possible
coordinates, and we don't know for sure whether we correctly interpret the
coordinates sent by the touchpad, so we clamp the reported values to
prevent confusion in userspace code.
Signed-off-by: Mathias Gottschlag <mgottschlag@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The size has in most cases already been fetched from the touchpad, the
hardcoded values should have been removed.
Signed-off-by: Mathias Gottschlag <mgottschlag@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This change adds device tree support and binding information for Goodix
GT9xx series touchscreen controller. It also adds support for 5-finger
chips, like GT911 and GT912, which can be found on ARM tablets, such as
Wexler TAB7200 and MSI Primo73.
Datasheets can be found here:
https://drive.google.com/folderview?id=0BxCVOQS3ZymGfmJyY2RKbE5XbVlKNlktVTlwV0lxNEdxd2dzeWZER094cmJPVnMxN1F0Yzg&usp=sharing
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use max number of touches from device config instead of hardcoding.
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Acked-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
According to Synaptics devices with ForcePads use SYN300D and SYN3014 as
PNP IDs, so let's switch from DMI-bases detection scheme to PNP-based
one, which should be more reliable.
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
PNP IDs are supposed to be case-insensitive and so we should compare
them as such.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds a key input driver for the keys found on the h3xxx
iPAQ series.
Based on a driver from handhelds.org 2.6.21 kernel, written
by Alessandro GARDICH.
Signed-off-by: Alessandro GARDICH <gremlin@gremlin.it>
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch adds support for haptic on max77843 MFD (Multi Function Device)
with PMIC, MUIC, LED, CHARGER.
This driver supports external pwm and LRA (Linear Resonant Actuator) motor.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
[Jim Davis <jim.epost@gmail.com>: should depend on REGULATOR not PWM]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since commit 1c6c69525b ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request will fail.
Currently, plat->irqtype is only set to IRQF_TRIGGER_FALLING. This
patch sets the ONESHOT flag directly in request_threaded_irq() to
enforce the flag without being affected by future changes to
plat->irqtype.
Generated by: scripts/coccinelle/misc/irqf_oneshot.cocci
Signed-off-by: Valentin Rothberg <Valentin.Rothberg@lip6.fr>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The gpio binding document says that new code should always use named
gpios. Patch 40b73183 added support to parse a list of gpios from child
nodes, but does not make it possible to use named gpios. This patch adds
the con_id property and implements it is done in gpiolib.c, where the
old-style of using unnamed gpios still works.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Bryan Wu <cooloney@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Broadcom Keypad controller is used to interface a SoC with a matrix-type
keypad device. The keypad controller supports multiple row and column
lines. A key can be placed at each intersection of a unique row and a
unique column. The keypad controller can sense a key-press and key-release
and report the event using an interrupt to the CPU.
Reviewed-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The sun4i-ts driver has had a dependency on the thermal code
with the addition of the thermal zone sensor support, but this
is not currently enforced in Kconfig, so with TOUCHSCREEN_SUN4I=y,
THERMAL=m and THERMAL_OF=y we get
drivers/built-in.o: In function `sun4i_ts_remove':
:(.text+0x2376f4): undefined reference to `thermal_zone_of_sensor_unregister'
drivers/built-in.o: In function `sun4i_ts_probe':
:(.text+0x237a94): undefined reference to `thermal_zone_of_sensor_register'
:(.text+0x237c00): undefined reference to `thermal_zone_of_sensor_unregister'
We need the dependency on THERMAL in order to ensure that this
driver becomes a loadable module if the thermal support itself
is modular, while the dependency on THERMAL_OF is a runtime
dependency and the driver will still build if it is missing.
It is entirely possible to build sun4i-ts without THERMAL_OF
just to use the hwmon sensors and/or touchscreen.
Fixes: 2236971079 ("Input: sun4i-ts - add thermal zone sensor support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[wens@csie.org: Fix description and Kconfig dependencies]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
drivers/input/mouse/cyapa_gen5.c: In function ‘cyapa_gen5_read_idac_data’:
drivers/input/mouse/cyapa_gen5.c:1876: warning: ‘max_element_cnt’ may be used uninitialized in this function
drivers/input/mouse/cyapa_gen5.c:1873: warning: ‘offset’ may be used uninitialized in this function
If *data_size is non-zero, and idac_data_type contains an unknown type,
max_element_cnt and offset will be uninitialized, and the loop will
process non-existing data.
However, this cannot happen (for now), as there's a test for unknown
types at the top of cyapa_gen5_read_idac_data().
As no "if ... else if ..." is used in other places, remove the
superfluous "if" to silence the compiler warning.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use asm/unaligned.h instead of linux/unaligned/access_ok.h header file to
fix compiling issues such as following while doing cross platform
compiling:
"include/linux/unaligned/access_ok.h:7:19: error: redefinition of
'get_unaligned_le16'
...
include/linux/unaligned/le_struct.h:6:19: note: previous definition of
'get_unaligned_le16' was here".
Reported-by: kbuild test robot <kbuild-all@01.org>
Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The cos table used at fixp-arith.h has only 8 bits of precision.
That causes problems if it is reused on other drivers.
As some media drivers require a higher precision sin/cos
implementation, replace the current implementation by one that
will provide 32 bits precision.
The values generated by the new implementation matches the
32 bit precision of glibc's sin for an angle measured in
integer degrees.
It also provides support for fractional angles via linear
interpolation. On experimental calculus, when used a table
with a 0.001 degree angle, the maximum error for sin is
0.000038, which is likely good enough for practical purposes.
There are some logic there that seems to be specific to the
usage inside ff-memless.c. Move those logic to there, as they're
not needed elsewhere.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The struct cros_ec_command will be used as an ioctl() argument for the
API to control the ChromeOS EC from user-space. So the data structure
has to be 64-bit safe to make it compatible between 32 and 64 avoiding
the need for a compat ioctl interface. Since pointers are self-aligned
to different byte boundaries, use fixed size arrays instead of pointers
for transferring ingoing and outgoing data with the Embedded Controller.
Also, re-arrange struct members by decreasing alignment requirements to
reduce the needing padding size.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add the parent device so that udev can show the full hierarchy. This avoids
the device showing up under /devices/virtual/input instead of the i2c bus
it is actually attached to.
Signed-off-by: Stefan Sauer <ensonic@google.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull more input updates from Dmitry Torokhov:
"The second round of updates for the input subsystem.
Updates to ALPS an bfin_roraty drivers and a couple oother fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: psmouse - use IS_ENABLED instead of homegrown code
Input: bfin_rotary - introduce open and close methods
Input: bfin_rotary - convert to use managed resources
Input: bfin_rotary - use generic IO functions
Input: bfin_rotary - move pin lists into into platform data
Input: bfin_rotary - move platform header to linux/platform_data
Input: bfin_rotary - mark suspend and resume code as __maybe_unused
Input: bfin_rotary - fix potential oops in interrupt handler
Input: ALPS - move v7 packet info to Documentation and v6 packet info
Input: ALPS - fix confusing comment in protocol data
Input: ALPS - do not mix trackstick and external PS/2 mouse data
Input: ALPS - fix trackstick detection on some Dell Latitudes
Input: ALPS - consolidate setting protocol parameters
Input: ALPS - split protocol data from model info
Input: ALPS - make Rushmore a separate protocol
Input: ALPS - renumber protocol numbers
Input: adi - remove an unnecessary check
Input: pxa27x_keypad - remove an unneeded NULL check
Input: soc_button_array - use "Windows" key for "Home"
Instead of having various protocols provide <protocol>_supported()
functions, let's use IS_ENABLED() macro that works well in "if" statements.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Introduce open and close methods for the input device to postpone enabling
the device until it is needed.
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use of managed resources simplifies error handling.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of using arch-specific accessors remap rotary register physical
address into kernel space in probe and use standard readw and writew to
access rotary MMRs.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Newer Blackfin boards use pinctrl API to manage pins and the legacy
peripherial lists are not useful on them. Let's move pin lists into
platform data so older boards can still use them and newer boards can use
the modern API.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The platform data definition of the rotary driver should be generic for all
architectures.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of using #ifdef to guard potentially unused suspend and resume code
let's mark them as __maybe_unused so they still get discarded if they are
not used but we do not get warning. This allows for better compile coverage.
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The interrupt handler in the driver tries to fetch driver data from
platform device, unfortunately it is only set up after interrupt handler
is registered. Since interrupt handler does not really need to access
the platform device itself let's change it to get the driver data
instance instead.
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch move all packet info from driver source code to documentation
and adds info about v6 packet format (from driver source code).
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The comment about suspicions entry 0x20, 0x02, 0x0e has over time drifted
away and it become hard to figure out what it meant. Let's move it back so
it is clear.
Reported-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Previously dev2 device was used for both external PS/2 mouse and internal
trackstick device (if available). This change introduces dev3 device which
is used for external PS/2 mouse data and dev2 is now used only for
trackstick.
In case that trackstick is not present dev2 is not created, so userspace
does not see non existent device in system.
Because laptops with ALPS devices often do not use i8042 active
multiplexing all data (from touchpad, trackstick and external PS/2 mouse)
come to one port. So it is not possible to know if external PS/2 mouse is
connected or not. In most cases external PS/2 mouse is not connected so
driver will create dev3 input device after first bare PS/2 packet will be
received. So there will not be "ghost" input device.
This change also helps in identifying possible problems in future if driver
decides to report 6-bytes trackstick packets as 3-bytes bare PS/2 (data
will be reported to dev3 instead dev2).
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On some Dell Latitudes we fail to identify presence of trackstick unless we
reset the device. The issue is quite benign as we do perform reset in
alps_init(), so the trackstick ends up working, but mouse name reported to
userspace is not accurate.
In order to fix the issue while avoiding the additional lengthy reset we
move the resrt to alps_detect() and keep the discovered state to be used
later in alps_init().
Reported-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Move setting of all protocol properties into alps_set_protocol (former
alps_set_defaults) instead of having it split between several functions.
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In preparation of reworking the way we set protocol parameters let's
split certain protocol items from alps_model_info into a separate
structure.
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Even though Rushmore is very close to V3 protocol it is sufficiently
different to warrant it's own protocol name.
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In order to accommodate new protocol number for Rushmore touchpads
let's shift protocol numbers by 8 bits (i.e. 1 -> 0x100) - this way
we keep protocol version reported in input device id the same as it
was, but add some holes in numbering.
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
printk and friends can now format bitmaps using '%*pb[l]'. cpumask
and nodemask also provide cpumask_pr_args() and nodemask_pr_args()
respectively which can be used to generate the two printf arguments
necessary to format the specified cpu/nodemask.
* Line termination only requires one extra space at the end of the
buffer. Use PAGE_SIZE - 1 instead of PAGE_SIZE - 2 when formatting.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Robin Gong