se_lun and se_lun_acl are immutable pointers of struct se_dev_entry.
Remove RCU usage for access to those pointers.
Link: https://lore.kernel.org/r/20220727214125.19647-3-d.bogdanov@yadro.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Dmitry Bogdanov <d.bogdanov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The se_cmd is unused in these functions, just remove it.
Link: https://lore.kernel.org/r/20210913083045.3670648-1-fengli@smartx.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Li Feng <fengli@smartx.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
TCM fails to pass the following tests in libiscsi:
SCSI.ExtendedCopy.DescrType
SCSI.ExtendedCopy.DescrLimits
SCSI.ExtendedCopy.ParamHdr
SCSI.ExtendedCopy.ValidSegDescr
SCSI.ExtendedCopy.ValidTgtDescr
The xcopy code always returns the same NOT READY sense key for all detected
errors. Change the sense key for invalid requests to ILLEGAL REQUEST, and
for aborted transfers to COPY ABORTED.
Link: https://lore.kernel.org/r/20210803145410.80147-3-s.samoylenko@yadro.com
Fixes: d877d7275b ("target: Fix a deadlock between the XCOPY code and iSCSI session shutdown")
Reviewed-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: Konstantin Shelekhin <k.shelekhin@yadro.com>
Signed-off-by: Sergey Samoylenko <s.samoylenko@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
target_complete_cmd() and friends requires a SAM status type, so passing
GOOD here is actually wrong.
Link: https://lore.kernel.org/r/20210427083046.31620-40-hare@suse.de
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Both the INQUIRY handling and the XCOPY implementation provide functions to
generate an NAA designator. In addition, these functions are poorly named:
- spc_parse_naa_6h_vendor_specific()
- target_xcopy_gen_naa_ieee()
Introduce a common NAA 6 designator generation function,
spc_gen_naa_6h_vendor_specific().
Link: https://lore.kernel.org/r/20210420185920.42431-2-s.samoylenko@yadro.com
Signed-off-by: Sergey Samoylenko <s.samoylenko@yadro.com>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
tcm_loop could be used like a normal block device, so we can't use
GFP_KERNEL and should use GFP_NOIO. This adds a gfp_t arg to
target_cmd_init_cdb() and converts the users. For every driver but loop
GFP_KERNEL is kept.
This will also be useful in subsequent patches where loop needs to do
target_submit_prep() from interrupt context to get a ref to the se_device,
and so it will need to use GFP_ATOMIC.
Link: https://lore.kernel.org/r/20210227170006.5077-16-michael.christie@oracle.com
Tested-by: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rename transport_init_se_cmd() to __target_init_cmd() to reflect that it is
more of an internal function that drivers should normally not use and
because we are going to add a new init function in the next patches.
Link: https://lore.kernel.org/r/20210227170006.5077-4-michael.christie@oracle.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When attempting to match EXTENDED COPY CSCD descriptors with corresponding
se_devices, target_xcopy_locate_se_dev_e4() currently iterates over LIO's
global devices list which includes all configured backstores.
This change ensures that only initiator-accessible backstores are
considered during CSCD descriptor lookup, according to the session's
se_node_acl LUN list.
To avoid LUN removal race conditions, device pinning is changed from being
configfs based to instead using the se_node_acl lun_ref.
Reference: CVE-2020-28374
Fixes: cbf031f425 ("target: Add support for EXTENDED_COPY copy offload emulation")
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
transport_init_session can allocate memory via percpu_ref_init, and
target_xcopy_release_pt never frees it. This adds a
transport_uninit_session function to handle cleanup of resources allocated
in the init function.
Link: https://lore.kernel.org/r/1593654203-12442-3-git-send-email-michael.christie@oracle.com
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This commit also removes the unused argument, cdb, that was passed to this
function.
Link: https://lore.kernel.org/r/1591559913-8388-5-git-send-email-sudhakar.panneerselvam@oracle.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Sudhakar Panneerselvam <sudhakar.panneerselvam@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NULL pointer dereference happens when the following conditions are met:
1) A SCSI command is received for a non-existing LU or cdb initialization
fails in target_setup_cmd_from_cdb().
2) Tracing is enabled.
The following call sequences lead to NULL pointer dereference:
1) iscsit_setup_scsi_cmd
transport_lookup_cmd_lun <-- lookup fails.
or
target_setup_cmd_from_cdb() <-- cdb initialization fails
iscsit_process_scsi_cmd
iscsit_sequence_cmd
transport_send_check_condition_and_sense
trace_target_cmd_complete <-- NULL dereference
2) target_submit_cmd_map_sgls
transport_lookup_cmd_lun <-- lookup fails
or
target_setup_cmd_from_cdb() <-- cdb initialization fails
transport_send_check_condition_and_sense
trace_target_cmd_complete <-- NULL dereference
In the above sequence, cmd->t_task_cdb is uninitialized which when
referenced in trace_target_cmd_complete() causes NULL pointer dereference.
The fix is to use the helper, target_cmd_init_cdb() and call it after
transport_init_se_cmd() is called, so that cmd->t_task_cdb can be
initialized and hence can be referenced in trace_target_cmd_complete().
Link: https://lore.kernel.org/r/1591559913-8388-4-git-send-email-sudhakar.panneerselvam@oracle.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Sudhakar Panneerselvam <sudhakar.panneerselvam@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Initialization of orig_fe_lun is moved to transport_init_se_cmd() from
transport_lookup_cmd_lun(). This helps for the cases where the SCSI request
fails before the call to transport_lookup_cmd_lun() so that
trace_target_cmd_complete() can print the LUN information to the trace
buffer. Due to this change, the lun parameter is removed from
transport_lookup_cmd_lun() and transport_lookup_tmr_lun().
Link: https://lore.kernel.org/r/1591559913-8388-3-git-send-email-sudhakar.panneerselvam@oracle.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Sudhakar Panneerselvam <sudhakar.panneerselvam@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reads and writes in the XCOPY loop are synchronous, so needn't be heap
allocated / freed with each loop.
Link: https://lore.kernel.org/r/20200327141954.955-6-ddiss@suse.de
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The main target_xcopy_do_work() loop unnecessarily allocates an I/O buffer
with each synchronous READ / WRITE pair. This commit significantly reduces
allocations by reusing the XCOPY I/O buffer when possible.
Link: https://lore.kernel.org/r/20200327141954.955-4-ddiss@suse.de
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The DISK BLOCK LENGTH field is carried with XCOPY target descriptors on the
wire, but is currently unmarshalled during 0x02 segment descriptor
passing. The unmarshalled value is currently unused, so drop it.
Link: https://lore.kernel.org/r/20200327141954.955-3-ddiss@suse.de
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Maintaining tpg_list without ever iterating over it is not useful. Hence
remove tpg_list. This patch does not change the behavior of the SCSI target
code.
Cc: Mike Christie <mchristie@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Link: https://lore.kernel.org/r/20190930232224.58980-1-bvanassche@acm.org
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The target_xcopy_setup_pt_port() and target_xcopy_init_pt_lun() functions
obfuscate what is really going on. Hence inline these two functions. This
patch does not change any functionality.
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Other than removing a few pr_debug() statements, this patch does not change
any functionality.
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch does not change any functionality.
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Due to the patch that makes TMF handling synchronous the
write_pending_status() callback function is no longer called. Hence remove
it.
Acked-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Andy Grover <agrover@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A session must only be released after all code that accesses the session
structure has finished. Make sure that this is the case by introducing a
new command counter per session that is only decremented after the
.release_cmd() callback has finished. This patch fixes the following crash:
BUG: KASAN: use-after-free in do_raw_spin_lock+0x1c/0x130
Read of size 4 at addr ffff8801534b16e4 by task rmdir/14805
CPU: 16 PID: 14805 Comm: rmdir Not tainted 4.18.0-rc2-dbg+ #5
Call Trace:
dump_stack+0xa4/0xf5
print_address_description+0x6f/0x270
kasan_report+0x241/0x360
__asan_load4+0x78/0x80
do_raw_spin_lock+0x1c/0x130
_raw_spin_lock_irqsave+0x52/0x60
srpt_set_ch_state+0x27/0x70 [ib_srpt]
srpt_disconnect_ch+0x1b/0xc0 [ib_srpt]
srpt_close_session+0xa8/0x260 [ib_srpt]
target_shutdown_sessions+0x170/0x180 [target_core_mod]
core_tpg_del_initiator_node_acl+0xf3/0x200 [target_core_mod]
target_fabric_nacl_base_release+0x25/0x30 [target_core_mod]
config_item_release+0x9c/0x110 [configfs]
config_item_put+0x26/0x30 [configfs]
configfs_rmdir+0x3b8/0x510 [configfs]
vfs_rmdir+0xb3/0x1e0
do_rmdir+0x262/0x2c0
do_syscall_64+0x77/0x230
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: David Disseldorp <ddiss@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
All fabrics return a const string. In all cases *except* iSCSI the
get_fabric_name() string matches fabric_ops.name.
Both fabric_ops.get_fabric_name() and fabric_ops.name are user-facing, with
the former being used for PR/ALUA state and the latter for ConfigFS
(config/target/$name), so we unfortunately need to keep both strings around
for now. Replace the useless .get_fabric_name() accessor function with a
const string fabric_name member variable.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A value is assigned to the xcopy_op member of struct xcopy_pt_cmd but
that value is never used. Hence remove the xcopy_op member.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Other than initializing xcopy_pt_sess.sess_wait_list, this patch does not
change any functionality.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This converts the xcopy code to use the idr helper. The next patch
will drop the g_device_list and make g_device_mutex local to the
target_core_device.c file.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Introduce the function get_unaligned_be24(). Use {get,put}_unaligned_be*()
where appropriate. This patch does not change any functionality.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Cc: Andy Grover <agrover@redhat.com>
Cc: David Disseldorp <ddiss@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds the missing target_complete_cmd() SCSI status
parameter change in target_xcopy_do_work(), that was originally
missing in commit 926317de33.
It correctly propigates up the correct SCSI status during
EXTENDED_COPY exception cases, instead of always using the
hardcoded SAM_STAT_CHECK_CONDITION from original code.
This is required for ESX host environments that expect to
hit SAM_STAT_RESERVATION_CONFLICT for certain scenarios,
and SAM_STAT_CHECK_CONDITION results in non-retriable
status for these cases.
Reported-by: Nixon Vincent <nixon.vincent@calsoftinc.com>
Tested-by: Nixon Vincent <nixon.vincent@calsoftinc.com>
Cc: Nixon Vincent <nixon.vincent@calsoftinc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org # 3.14+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
SPC4r37 6.4.1 EXTENDED COPY(LID4) states (also applying to LID1 reqs):
A parameter list length of zero specifies that the copy manager shall
not transfer any data or alter any internal state, and this shall not
be considered an error.
This behaviour can be tested using the libiscsi ExtendedCopy.ParamHdr
test.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Check for XCOPY header, CSCD descriptor and segment descriptor list
truncation, and respond accordingly.
SPC4r37 6.4.1 EXTENDED COPY(LID4) states (also applying to LID1 reqs):
If the parameter list length causes truncation of the parameter list,
then the copy manager shall transfer no data and shall terminate the
EXTENDED COPY command with CHECK CONDITION status, with the sense key
set to ILLEGAL REQUEST, and the additional sense code set to PARAMETER
LIST LENGTH ERROR.
This behaviour can be tested using the libiscsi ExtendedCopy.ParamHdr
test.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
The XCOPY specification in SPC4r37 states that the XCOPY source and
destination device(s) should be derived from the copy source and copy
destination (CSCD) descriptor IDs in the XCOPY segment descriptor.
The CSCD IDs are generally (for block -> block copies), indexes into
the corresponding CSCD descriptor list, e.g.
=================================
EXTENDED COPY Header
=================================
CSCD Descriptor List
- entry 0
+ LU ID <--------------<------------------\
- entry 1 |
+ LU ID <______________<_____________ |
================================= | |
Segment Descriptor List | |
- segment 0 | |
+ src CSCD ID = 0 --------->---------+----/
+ dest CSCD ID = 1 ___________>______|
+ len
+ src lba
+ dest lba
=================================
Currently LIO completely ignores the src and dest CSCD IDs in the
Segment Descriptor List, and instead assumes that the first entry in the
CSCD list corresponds to the source, and the second to the destination.
This commit removes this assumption, by ensuring that the Segment
Descriptor List is parsed prior to processing the CSCD Descriptor List.
CSCD Descriptor List processing is modified to compare the current list
index with the previously obtained src and dest CSCD IDs.
Additionally, XCOPY requests where the src and dest CSCD IDs refer to
the CSCD Descriptor List entry can now be successfully processed.
Fixes: cbf031f ("target: Add support for EXTENDED_COPY copy offload")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=191381
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Ensure that the segment descriptor CSCD descriptor ID values correspond
to CSCD descriptor entries located in the XCOPY command parameter list.
SPC4r37 6.4.6.1 Table 150 specifies this range as 0000h to 07FFh, where
the CSCD descriptor location in the parameter list can be located via:
16 + (id * 32)
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
[ bvanassche: inserted "; " in the format string of an error message
and also moved a "||" operator from the start of a line to the end
of the previous line ]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
target_xcopy_locate_se_dev_e4() is used to locate an se_dev, based on
the WWN provided with the XCOPY request. Remove a couple of unneeded
arguments, and rely on the caller for the src/dst test.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Use UNSUPPORTED TARGET DESCRIPTOR TYPE CODE and UNSUPPORTED SEGMENT
DESCRIPTOR TYPE CODE additional sense codes if a descriptor type in an
XCOPY request is not supported, as specified in spc4r37 6.4.5 and 6.4.6.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
spc4r37 6.4.3.5 states:
If the combined length of the CSCD descriptors and segment descriptors
exceeds the allowed value, then the copy manager shall terminate the
command with CHECK CONDITION status, with the sense key set to ILLEGAL
REQUEST, and the additional sense code set to PARAMETER LIST LENGTH
ERROR.
This functionality can be tested using the libiscsi
ExtendedCopy.DescrLimits test.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Check the length of the XCOPY request segment descriptor list against
the value advertised via the MAXIMUM SEGMENT DESCRIPTOR COUNT field in
the RECEIVE COPY OPERATING PARAMETERS response.
spc4r37 6.4.3.5 states:
If the number of segment descriptors exceeds the allowed number, the
copy manager shall terminate the command with CHECK CONDITION status,
with the sense key set to ILLEGAL REQUEST, and the additional sense
code set to TOO MANY SEGMENT DESCRIPTORS.
This functionality is testable using the libiscsi
ExtendedCopy.DescrLimits test.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
spc4r37 6.4.3.4 states:
If the number of CSCD descriptors exceeds the allowed number, the copy
manager shall terminate the command with CHECK CONDITION status, with
the sense key set to ILLEGAL REQUEST, and the additional sense code
set to TOO MANY TARGET DESCRIPTORS.
LIO currently responds with INVALID FIELD IN PARAMETER LIST, which sees
it fail the libiscsi ExtendedCopy.DescrLimits test.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Remove superfluous #include directives from the include/target/*.h
files. Add missing #include directives to other *.h and *.c files.
Use forward declarations for structures where possible. This
change reduces the build time for make M=drivers/target on my
laptop from 27.1s to 18.7s or by about 30%.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
This patch addresses a bug where a local EXTENDED_COPY WRITE or READ
backend I/O request would always return SAM_STAT_CHECK_CONDITION,
even if underlying xcopy_pt_cmd->se_cmd generated a different
SCSI status code.
ESX host environments expect to hit SAM_STAT_RESERVATION_CONFLICT
for certain scenarios, and SAM_STAT_CHECK_CONDITION results in
non-retriable status for these cases.
Tested on v4.1.y with ESX v5.5u2+ with local IBLOCK backend copy.
Reported-by: Nixon Vincent <nixon.vincent@calsoftinc.com>
Tested-by: Nixon Vincent <nixon.vincent@calsoftinc.com>
Cc: Nixon Vincent <nixon.vincent@calsoftinc.com>
Tested-by: Dinesh Israni <ddi@datera.io>
Signed-off-by: Dinesh Israni <ddi@datera.io>
Cc: Dinesh Israni <ddi@datera.io>
Cc: stable@vger.kernel.org # 3.14+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses a bug where EXTENDED_COPY across multiple LUNs
results in a CHECK_CONDITION when the source + destination are not
located on the same physical node.
ESX Host environments expect sense COPY_ABORTED w/ COPY TARGET DEVICE
NOT REACHABLE to be returned when this occurs, in order to signal
fallback to local copy method.
As described in section 6.3.3 of spc4r22:
"If it is not possible to complete processing of a segment because the
copy manager is unable to establish communications with a copy target
device, because the copy target device does not respond to INQUIRY,
or because the data returned in response to INQUIRY indicates
an unsupported logical unit, then the EXTENDED COPY command shall be
terminated with CHECK CONDITION status, with the sense key set to
COPY ABORTED, and the additional sense code set to COPY TARGET DEVICE
NOT REACHABLE."
Tested on v4.1.y with ESX v5.5u2+ with BlockCopy across multiple nodes.
Reported-by: Nixon Vincent <nixon.vincent@calsoftinc.com>
Tested-by: Nixon Vincent <nixon.vincent@calsoftinc.com>
Cc: Nixon Vincent <nixon.vincent@calsoftinc.com>
Tested-by: Dinesh Israni <ddi@datera.io>
Signed-off-by: Dinesh Israni <ddi@datera.io>
Cc: Dinesh Israni <ddi@datera.io>
Cc: stable@vger.kernel.org # 3.14+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The SRP target driver will need to allocate and chain it's own SGLs soon.
For this export target_alloc_sgl, and add a new argument to it so that it
can allocate an additional chain entry that doesn't point to a page. Also
export transport_free_sgl after renaming it to target_free_sgl to free
these SGLs again.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch is a >= v4.1 regression bug-fix where control CDB
emulation logic in commit 38b57f82 now expects a se_cmd->se_sess
pointer to exist when determining T10-PI support is to be exposed
for initiator host ports.
To address this bug, go ahead and add locally generated se_cmd
descriptors for copy-offload block-copy to it's own stand-alone
se_session nexus, while the parent EXTENDED_COPY se_cmd descriptor
remains associated with it's originating se_cmd->se_sess nexus.
Note a valid se_cmd->se_sess is also required for future support
of WRITE_INSERT and READ_STRIP software emulation when submitting
backend I/O to se_device that exposes T10-PI suport.
Reported-by: Alex Gorbachev <ag@iss-integration.com>
Tested-by: Alex Gorbachev <ag@iss-integration.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Doug Gilbert <dgilbert@interlog.com>
Cc: <stable@vger.kernel.org> # v4.1+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull SCSI target updates from Nicholas Bellinger:
"It's been a busy development cycle for target-core in a number of
different areas.
The fabric API usage for se_node_acl allocation is now within
target-core code, dropping the external API callers for all fabric
drivers tree-wide.
There is a new conversion to RCU hlists for se_node_acl and
se_portal_group LUN mappings, that turns fast-past LUN lookup into a
completely lockless code-path. It also removes the original
hard-coded limitation of 256 LUNs per fabric endpoint.
The configfs attributes for backends can now be shared between core
and driver code, allowing existing drivers to use common code while
still allowing flexibility for new backend provided attributes.
The highlights include:
- Merge sbc_verify_dif_* into common code (sagi)
- Remove iscsi-target support for obsolete IFMarker/OFMarker
(Christophe Vu-Brugier)
- Add bidi support in target/user backend (ilias + vangelis + agover)
- Move se_node_acl allocation into target-core code (hch)
- Add crc_t10dif_update common helper (akinobu + mkp)
- Handle target-core odd SGL mapping for data transfer memory
(akinobu)
- Move transport ID handling into target-core (hch)
- Move task tag into struct se_cmd + support 64-bit tags (bart)
- Convert se_node_acl->device_list[] to RCU hlist (nab + hch +
paulmck)
- Convert se_portal_group->tpg_lun_list[] to RCU hlist (nab + hch +
paulmck)
- Simplify target backend driver registration (hch)
- Consolidate + simplify target backend attribute implementations
(hch + nab)
- Subsume se_port + t10_alua_tg_pt_gp_member into se_lun (hch)
- Drop lun_sep_lock for se_lun->lun_se_dev RCU usage (hch + nab)
- Drop unnecessary core_tpg_register TFO parameter (nab)
- Use 64-bit LUNs tree-wide (hannes)
- Drop left-over TARGET_MAX_LUNS_PER_TRANSPORT limit (hannes)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (76 commits)
target: Bump core version to v5.0
target: remove target_core_configfs.h
target: remove unused TARGET_CORE_CONFIG_ROOT define
target: consolidate version defines
target: implement WRITE_SAME with UNMAP bit using ->execute_unmap
target: simplify UNMAP handling
target: replace se_cmd->execute_rw with a protocol_data field
target/user: Fix inconsistent kmap_atomic/kunmap_atomic
target: Send UA when changing LUN inventory
target: Send UA upon LUN RESET tmr completion
target: Send UA on ALUA target port group change
target: Convert se_lun->lun_deve_lock to normal spinlock
target: use 'se_dev_entry' when allocating UAs
target: Remove 'ua_nacl' pointer from se_ua structure
target_core_alua: Correct UA handling when switching states
xen-scsiback: Fix compile warning for 64-bit LUN
target: Remove TARGET_MAX_LUNS_PER_TRANSPORT
target: use 64-bit LUNs
target: Drop duplicate + unused se_dev_check_wce
target: Drop unnecessary core_tpg_register TFO parameter
...
This is the usual grab bag of driver updates (lpfc, hpsa,
megaraid_sas, cxgbi, be2iscsi) plus an assortment of minor updates.
There are also one new driver: the Cisco snic; the advansys driver has
been rewritten to get rid of the warning about converting it to the
DMA API, the tape statistics patch got in and finally, there's a
resuffle of SCSI header files to separate more cleanly initiator from
target mode (and better share the common definitions).
Signed-off-by: James Bottomley <JBottomley@Odin.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJViKWdAAoJEDeqqVYsXL0MAr8IAMmlA6HBVjMJJFCEOY9corHj
e70MNQa7LUgf+JCdOtzGcvHXTiFFd4IHZAwXUJAnsC4IU2QWEfi1bjUTErlqBIGk
LoZlXXpEHnFpmWot3OluOzzcGcxede8rVgPiKWVVdojIngBC2+LL/i2vPCJ84ri9
WCVlk6KBvWZXuU6JuOKAb2FO9HOX7Q61wuKAMast2Qc6RNc2ksgc7VbstsITqzZ9
FVEsjmQ5lqUj+xdxBpiUOdUpc22IJ4VcpBgQ2HrThvg6vf4aq937RJ/g4vi/g0SU
Utk0a3bUw1H/WnYAfJVFx83nVEsS/954Z7/ERDg1sjlfLYwQtQnpov0XIbPIbZU=
=k9IT
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is the usual grab bag of driver updates (lpfc, hpsa,
megaraid_sas, cxgbi, be2iscsi) plus an assortment of minor updates.
There is also one new driver: the Cisco snic. The advansys driver has
been rewritten to get rid of the warning about converting it to the
DMA API, the tape statistics patch got in and finally, there's a
resuffle of SCSI header files to separate more cleanly initiator from
target mode (and better share the common definitions)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (156 commits)
snic: driver for Cisco SCSI HBA
qla2xxx: Fix indentation
qla2xxx: Comment out unreachable code
fusion: remove dead MTRR code
advansys: fix compilation errors and warnings when CONFIG_PCI is not set
mptsas: fix depth param in scsi_track_queue_full
megaraid: fix irq setup process regression
lpfc: Update version to 10.7.0.0 for upstream patch set.
lpfc: Fix to drop PLOGIs from fabric node till LOGO processing completes
lpfc: Fix scsi task management error message.
lpfc: Fix cq_id masking problem.
lpfc: Fix scsi prep dma buf error.
lpfc: Add support for using block multi-queue
lpfc: Devices are not discovered during takeaway/giveback testing
lpfc: Fix vport deletion failure.
lpfc: Check for active portpeerbeacon.
lpfc: Update driver version for upstream patch set 10.6.0.1.
lpfc: Change buffer pool empty message to miscellaneous category
lpfc: Fix incorrect log message reported for empty FCF record.
lpfc: Fix rport leak.
...
Only include SCSI initiator header files in target code that needs
these header files, namely the SCSI pass-through code and the tcm_loop
driver. Change SCSI_SENSE_BUFFERSIZE into TRANSPORT_SENSE_BUFFER in
target code because the former is intended for initiator code and the
latter for target code. With this patch the only initiator include
directives in target code that remain are as follows:
$ git grep -nHE 'include .scsi/(scsi.h|scsi_host.h|scsi_device.h|scsi_cmnd.h)' drivers/target drivers/infiniband/ulp/{isert,srpt} drivers/usb/gadget/legacy/tcm_*.[ch] drivers/{vhost,xen} include/{target,trace/events/target.h}
drivers/target/loopback/tcm_loop.c:29:#include <scsi/scsi.h>
drivers/target/loopback/tcm_loop.c:31:#include <scsi/scsi_host.h>
drivers/target/loopback/tcm_loop.c:32:#include <scsi/scsi_device.h>
drivers/target/loopback/tcm_loop.c:33:#include <scsi/scsi_cmnd.h>
drivers/target/target_core_pscsi.c:39:#include <scsi/scsi_device.h>
drivers/target/target_core_pscsi.c:40:#include <scsi/scsi_host.h>
drivers/xen/xen-scsiback.c:52:#include <scsi/scsi_host.h> /* SG_ALL */
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
This patch eliminates all se_port + t10_alua_tg_pt_gp_member usage,
and converts current users to direct se_lun pointer dereference.
This includes the removal of core_export_port(), core_release_port()
core_dev_export() and core_dev_unexport(). Along with conversion
of special case se_lun pointer dereference within PR ALL_TG_PT=1
and ALUA access state transition UNIT_ATTENTION handling.
Also, update core_enable_device_list_for_node() to reference the
new per se_lun->lun_deve_list when creating a new entry, or
replacing an existing one via RCU.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Simplify target core and target drivers by storing the task tag
a.k.a. command identifier inside struct se_cmd.
For several transports (e.g. SRP) tags are 64 bits wide.
Hence add support for 64-bit tags.
(Fix core_tmr_abort_task conversion spec warnings - nab)
(Fix up usb-gadget to use 16-bit tags - HCH + bart)
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: <qla2xxx-upstream@qlogic.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Dmitry Bogdanov