Most of the ACS quirks have a similar pattern of:
acs_flags &= ~( <controls provided by this device> );
return acs_flags ? 0 : 1;
Pull this out into a helper function to simplify the quirks slightly. The
helper function is also a convenient place for comments about what the list
of ACS controls means. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
The ACS quirks differ in needless ways, which makes them look more
different than they really are.
Reorder the ACS flags in order of definitions in the spec:
PCI_ACS_SV Source Validation
PCI_ACS_TB Translation Blocking
PCI_ACS_RR P2P Request Redirect
PCI_ACS_CR P2P Completion Redirect
PCI_ACS_UF Upstream Forwarding
PCI_ACS_EC P2P Egress Control
PCI_ACS_DT Direct Translated P2P
(PCIe r5.0, sec 7.7.8.2) and use similar code structure in all. No
functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Enhance the ACS quirk for Cavium Processors. Add the root port vendor IDs
for ThunderX2 and ThunderX3 series of processors.
[bhelgaas: add Fixes: and stable tag]
Fixes: f2ddaf8dfd ("PCI: Apply Cavium ThunderX ACS quirk to more Root Ports")
Link: https://lore.kernel.org/r/20191111024243.GA11408@dc5-eodlnx05.marvell.com
Signed-off-by: George Cherian <george.cherian@marvell.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Robert Richter <rrichter@marvell.com>
Cc: stable@vger.kernel.org # v4.12+
Intel Visual Compute Accelerator (VCA) is a family of PCIe add-in devices
exposing computational units via Non Transparent Bridges (NTB, PEX 87xx).
Similarly to MIC x200, we need to add DMA aliases to allow buffer access
when IOMMU is enabled.
Add aliases to allow computational unit access to host memory. These
aliases mark the whole VCA device as one IOMMU group.
All possible slot numbers (0x20) are used, since we are unable to tell what
slot is used on other side. This quirk is intended for both host and
computational unit sides. The VCA devices have up to five functions: four
for DMA channels and one additional.
Link: https://lore.kernel.org/r/5683A335CC8BE1438C3C30C49DCC38DF637CED8E@IRSMSX102.ger.corp.intel.com
Signed-off-by: Slawomir Pawlowski <slawomir.pawlowski@intel.com>
Signed-off-by: Przemek Kitszel <przemyslawx.kitszel@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
According to documentation [0] the correct offset for the Upstream Peer
Decode Configuration Register (UPDCR) is 0x1014. It was previously defined
as 0x1114.
d99321b63b ("PCI: Enable quirks for PCIe ACS on Intel PCH root ports")
intended to enforce isolation between PCI devices allowing them to be put
into separate IOMMU groups. Due to the wrong register offset the intended
isolation was not fully enforced. This is fixed with this patch.
Please note that I did not test this patch because I have no hardware that
implements this register.
[0] https://www.intel.com/content/dam/www/public/us/en/documents/datasheets/4th-gen-core-family-mobile-i-o-datasheet.pdf (page 325)
Fixes: d99321b63b ("PCI: Enable quirks for PCIe ACS on Intel PCH root ports")
Link: https://lore.kernel.org/r/7a3505df-79ba-8a28-464c-88b83eefffa6@kernkonzept.com
Signed-off-by: Steffen Liebergeld <steffen.liebergeld@kernkonzept.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Ashok Raj <ashok.raj@intel.com>
Cc: stable@vger.kernel.org # v3.15+
Code that iterates over all standard PCI BARs typically uses
PCI_STD_RESOURCE_END. However, that requires the unusual test
"i <= PCI_STD_RESOURCE_END" rather than something the typical
"i < PCI_STD_NUM_BARS".
Add a definition for PCI_STD_NUM_BARS and change loops to use the more
idiomatic C style to help avoid fencepost errors.
Link: https://lore.kernel.org/r/20190927234026.23342-1-efremov@linux.com
Link: https://lore.kernel.org/r/20190927234308.23935-1-efremov@linux.com
Link: https://lore.kernel.org/r/20190916204158.6889-3-efremov@linux.com
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Sebastian Ott <sebott@linux.ibm.com> # arch/s390/
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> # video/fbdev/
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com> # pci/controller/dwc/
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com> # scsi/pm8001/
Acked-by: Martin K. Petersen <martin.petersen@oracle.com> # scsi/pm8001/
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # memstick/
- Fix Tegra OF node reference leak (Nishka Dasgupta)
- Add #defines for PCIe Data Link Feature and Physical Layer 16.0 GT/s
features (Vidya Sagar)
- Disable MSI for Tegra Root Ports since they don't support using MSI for
all Root Port events (Vidya Sagar)
- Group DesignWare write-protected register writes together (Vidya Sagar)
- Move DesignWare capability search interfaces so they can be used by
both host and endpoint drivers (Vidya Sagar)
- Add DesignWare extended capability search interfaces (Vidya Sagar)
- Export dw_pcie_wait_for_link() so drivers can be modules (Vidya Sagar)
- Add "snps,enable-cdm-check" DT binding for Configuration Dependent
Module (CDM) register checking (Vidya Sagar)
- Add DesignWare support for "snps,enable-cdm-check" CDM checking (Vidya
Sagar)
- Add "supports-clkreq" DT binding for host drivers to decide whether to
advertise low power features (Vidya Sagar)
- Add DT binding for Tegra194 (Vidya Sagar)
- Add DT binding for Tegra194 P2U (PIPE to UPHY) block (Vidya Sagar)
- Add support for Tegra194 P2U (PIPE to UPHY) (Vidya Sagar)
- Add support for Tegra194 host controller (Vidya Sagar)
- Add Tegra support for sideband PERST# and CLKREQ# for C5 (Vidya Sagar)
- Add Tegra support for slot regulators for p2972-0000 platform (Vidya
Sagar)
* lorenzo/pci/tegra:
arm64: tegra: Add PCIe slot supply information in p2972-0000 platform
arm64: tegra: Add configuration for PCIe C5 sideband signals
PCI: tegra: Add support to enable slot regulators
PCI: tegra: Add support to configure sideband pins
dt-bindings: PCI: tegra: Add PCIe slot supplies regulator entries
dt-bindings: PCI: tegra: Add sideband pins configuration entries
PCI: tegra: Add Tegra194 PCIe support
phy: tegra: Add PCIe PIPE2UPHY support
dt-bindings: PHY: P2U: Add Tegra194 P2U block
dt-bindings: PCI: tegra: Add device tree support for Tegra194
dt-bindings: Add PCIe supports-clkreq property
PCI: dwc: Add support to enable CDM register check
dt-bindings: PCI: designware: Add binding for CDM register check
PCI: dwc: Export dw_pcie_wait_for_link() API
PCI: dwc: Add extended configuration space capability search API
PCI: dwc: Move config space capability search API
PCI: dwc: Group DBI registers writes requiring unlocking
PCI: Disable MSI for Tegra root ports
PCI: Add #defines for some of PCIe spec r4.0 features
PCI: tegra: Fix OF node reference leak
- Use devm_add_action_or_reset() helper (Fuqian Huang)
- Mark expected switch fall-through (Gustavo A. R. Silva)
- Convert sysfs device attributes from __ATTR() to DEVICE_ATTR() (Kelsey
Skunberg)
- Convert sysfs file permissions from S_IRUSR etc to octal (Kelsey
Skunberg)
- Move SR-IOV sysfs functions to iov.c (Kelsey Skunberg)
- Add pci_info_ratelimited() to ratelimit PCI messages separately
(Krzysztof Wilczynski)
- Fix "'static' not at beginning of declaration" warnings (Krzysztof
Wilczynski)
- Clean up resource_alignment parameter to not require static buffer
(Logan Gunthorpe)
- Add ACS quirk for iProc PAXB (Abhinav Ratna)
- Add pci_irq_vector() and other stubs for !CONFIG_PCI (Herbert Xu)
* pci/misc:
PCI: Add pci_irq_vector() and other stubs when !CONFIG_PCI
PCI: Add ACS quirk for iProc PAXB
PCI: Force trailing new line to resource_alignment_param in sysfs
PCI: Move pci_[get|set]_resource_alignment_param() into their callers
PCI: Clean up resource_alignment parameter to not require static buffer
PCI: Use static const struct, not const static struct
PCI: Add pci_info_ratelimited() to ratelimit PCI separately
PCI/IOV: Remove group write permission from sriov_numvfs, sriov_drivers_autoprobe
PCI/IOV: Move sysfs SR-IOV functions to iov.c
PCI: sysfs: Change permissions from symbolic to octal
PCI: sysfs: Change DEVICE_ATTR() to DEVICE_ATTR_WO()
PCI: sysfs: Define device attributes with DEVICE_ATTR*()
PCI: Mark expected switch fall-through
PCI: Use devm_add_action_or_reset()
The Root Port (identified by [1c36:0031]) doesn't support MSI-X. On some
platforms it is configured to not advertise the capability at all, while
on others it (mistakenly) does. This causes a panic during
initialization by the pcieport driver, since it tries to configure the
MSI-X capability. Specifically, when trying to access the MSI-X table
a "non-existing addr" exception occurs.
Example stacktrace snippet:
SError Interrupt on CPU2, code 0xbf000000 -- SError
CPU: 2 PID: 1 Comm: swapper/0 Not tainted 5.2.0-rc1-Jonny-14847-ge76f1d4a1828-dirty #33
Hardware name: Annapurna Labs Alpine V3 EVP (DT)
pstate: 80000005 (Nzcv daif -PAN -UAO)
pc : __pci_enable_msix_range+0x4e4/0x608
lr : __pci_enable_msix_range+0x498/0x608
sp : ffffff80117db700
x29: ffffff80117db700 x28: 0000000000000001
x27: 0000000000000001 x26: 0000000000000000
x25: ffffffd3e9d8c0b0 x24: 0000000000000000
x23: 0000000000000000 x22: 0000000000000000
x21: 0000000000000001 x20: 0000000000000000
x19: ffffffd3e9d8c000 x18: ffffffffffffffff
x17: 0000000000000000 x16: 0000000000000000
x15: ffffff80116496c8 x14: ffffffd3e9844503
x13: ffffffd3e9844502 x12: 0000000000000038
x11: ffffffffffffff00 x10: 0000000000000040
x9 : ffffff801165e270 x8 : ffffff801165e268
x7 : 0000000000000002 x6 : 00000000000000b2
x5 : ffffffd3e9d8c2c0 x4 : 0000000000000000
x3 : 0000000000000000 x2 : 0000000000000000
x1 : 0000000000000000 x0 : ffffffd3e9844680
Kernel panic - not syncing: Asynchronous SError Interrupt
CPU: 2 PID: 1 Comm: swapper/0 Not tainted 5.2.0-rc1-Jonny-14847-ge76f1d4a1828-dirty #33
Hardware name: Annapurna Labs Alpine V3 EVP (DT)
Call trace:
dump_backtrace+0x0/0x140
show_stack+0x14/0x20
dump_stack+0xa8/0xcc
panic+0x140/0x334
nmi_panic+0x6c/0x70
arm64_serror_panic+0x74/0x88
__pte_error+0x0/0x28
el1_error+0x84/0xf8
__pci_enable_msix_range+0x4e4/0x608
pci_alloc_irq_vectors_affinity+0xdc/0x150
pcie_port_device_register+0x2b8/0x4e0
pcie_portdrv_probe+0x34/0xf0
Notice that this quirk also disables MSI (which may work, but hasn't
been tested nor has a current use case), since currently there is no
standard way to disable only MSI-X.
Signed-off-by: Jonathan Chocron <jonnyc@amazon.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
The Amazon's Annapurna Labs root ports don't advertise an ACS
capability, but they don't allow peer-to-peer transactions and do
validate bus numbers through the SMMU. Additionally, it's not possible
for one RP to pass traffic to another RP.
Signed-off-by: Ali Saidi <alisaidi@amazon.com>
Signed-off-by: Jonathan Chocron <jonnyc@amazon.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
iProc PAXB Root Ports don't advertise an ACS capability, but they do not
allow peer-to-peer transactions between Root Ports. Add an ACS quirk so
each Root Port can be in a separate IOMMU group.
[bhelgaas: commit log, comment, use common implementation style]
Link: https://lore.kernel.org/r/1566275985-25670-1-git-send-email-srinath.mannam@broadcom.com
Signed-off-by: Abhinav Ratna <abhinav.ratna@broadcom.com>
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Move ASPM definitions and function prototypes from include/linux/pci-aspm.h
to include/linux/pci.h so users only need to include <linux/pci.h>:
PCIE_LINK_STATE_L0S
PCIE_LINK_STATE_L1
PCIE_LINK_STATE_CLKPM
pci_disable_link_state()
pci_disable_link_state_locked()
pcie_no_aspm()
No functional changes intended.
Link: https://lore.kernel.org/r/20190827095620.11213-1-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
quirk_reset_lenovo_thinkpad_50_nvgpu() resets NVIDIA GPUs to work around
an apparent BIOS defect. It previously used pci_reset_function(), and
the available method was a bus reset, which was fine because there was
only one function on the bus. After b516ea586d ("PCI: Enable NVIDIA
HDA controllers"), there are now two functions (the HDA controller and
the GPU itself) on the bus, so the reset fails.
Use pci_reset_bus() explicitly instead of pci_reset_function() since it's
OK to reset both devices.
[bhelgaas: commit log, add e0547c81bf]
Fixes: b516ea586d ("PCI: Enable NVIDIA HDA controllers")
Fixes: e0547c81bf ("PCI: Reset Lenovo ThinkPad P50 nvgpu at boot if necessary")
Link: https://lore.kernel.org/r/20190801220117.14952-1-lyude@redhat.com
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Daniel Drake <drake@endlessm.com>
Cc: Aaron Plattner <aplattner@nvidia.com>
Cc: Peter Wu <peter@lekensteyn.nl>
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: Karol Herbst <kherbst@redhat.com>
Cc: Maik Freudenberg <hhfeuer@gmx.de>
Tegra PCIe rootports don't generate MSI interrupts for PME and AER events.
Since PCIe spec (Ref: r4.0 sec 7.7.1.2 and 7.7.2.2) doesn't support using
a mix of INTx and MSI/MSI-X, MSI needs to be disabled to avoid root ports
service drivers registering their respective ISRs with MSI interrupt and
to let only INTx be used for all events.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Many NVIDIA GPUs can be configured as either a single-function video device
or a multi-function device with video at function 0 and an HDA audio
controller at function 1. The HDA controller can be enabled or disabled by
a bit in the function 0 config space.
Some BIOSes leave the HDA disabled, which means the HDMI connector from the
NVIDIA GPU may not work. Sometimes the BIOS enables the HDA if an HDMI
cable is connected at boot time, but that doesn't handle hotplug cases.
Enable the HDA controller on device enumeration and resume and re-read the
header type, which tells us whether the GPU is a multi-function device.
This quirk is limited to NVIDIA PCI devices with the VGA Controller device
class. This is expected to correspond to product configurations where the
NVIDIA GPU has connectors attached. Other products where the device class
is 3D Controller are expected to correspond to configurations where the
NVIDIA GPU is dedicated (dGPU) and has no connectors. See original post
(URL below) for more details.
This commit takes inspiration from an earlier patch by Daniel Drake.
Link: https://lore.kernel.org/r/20190708051744.24039-1-drake@endlessm.com v2
Link: https://lore.kernel.org/r/20190613063514.15317-1-drake@endlessm.com v1
Link: https://devtalk.nvidia.com/default/topic/1024022
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=75985
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Daniel Drake <drake@endlessm.com>
[bhelgaas: commit log, log message, return early if already enabled]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Aaron Plattner <aplattner@nvidia.com>
Cc: Peter Wu <peter@lekensteyn.nl>
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: Karol Herbst <kherbst@redhat.com>
Cc: Maik Freudenberg <hhfeuer@gmx.de>
The NVIDIA Turing GPU is a multi-function PCI device with the following
functions:
- Function 0: VGA display controller
- Function 1: Audio controller
- Function 2: USB xHCI Host controller
- Function 3: USB Type-C UCSI controller
Function 0 is tightly coupled with other functions in the hardware. When
function 0 is in D3, it gates power for hardware blocks used by other
functions, which means those functions only work when function 0 is in D0.
If any of these functions (1/2/3) are in D0, then function 0 should also be
in D0.
Commit 07f4f97d7b ("vga_switcheroo: Use device link for HDA controller")
already creates a device link to show the dependency of function 1 on
function 0 of this GPU. Create additional device links to express the
dependencies of functions 2 and 3 on function 0. This means function 0
will be in D0 if any other function is in D0.
[bhelgaas: I think the PCI spec expectation is that functions can be
power-managed independently, so I don't think this device is technically
compliant. For example, the PCIe r5.0 spec, sec 1.4, says "the PCI/PCIe
hardware/software model includes architectural constructs necessary to
discover, configure, and use a Function, without needing Function-specific
knowledge" and sec 5.1 says "D states are associated with a particular
Function" and "PM provides ... a mechanism to identify power management
capabilities of a given Function [and] the ability to transition a Function
into a certain power management state."]
Link: https://lore.kernel.org/lkml/20190606092225.17960-3-abhsahu@nvidia.com
Signed-off-by: Abhishek Sahu <abhsahu@nvidia.com>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Although not allowed by the PCI specs, some multi-function devices have
power dependencies between the functions. For example, function 1 may not
work unless function 0 is in the D0 power state.
The existing quirk_gpu_hda() adds a device link to express this dependency
for GPU and HDA devices, but it really is not specific to those device
types.
Generalize it and rename it to pci_create_device_link() so we can create
dependencies between any "consumer" and "producer" functions of a
multi-function device, where the consumer is only functional if the
producer is in D0. This reorganization should not affect any
functionality.
Link: https://lore.kernel.org/lkml/20190606092225.17960-2-abhsahu@nvidia.com
Signed-off-by: Abhishek Sahu <abhsahu@nvidia.com>
[bhelgaas: commit log, reword diagnostic]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/printk:
PCI: Replace dev_printk(KERN_DEBUG) with dev_info(), etc
PCI: Replace printk(KERN_INFO) with pr_info(), etc
PCI: Use dev_printk() when possible
- Mark ATS on AMD Stoney Radeon R7 GPU broken to avoid IOMMU issues
(Nikolai Kostrigin)
- Mark Atheros AR9462 to avoid bus reset that locks up host machine
(James Prestwood)
* pci/virtualization:
PCI: Mark Atheros AR9462 to avoid bus reset
PCI: Mark AMD Stoney Radeon R7 GPU ATS as broken
Replace dev_printk(KERN_DEBUG) with dev_info(), etc to be more consistent
with other logging and avoid checkpatch warnings.
The KERN_DEBUG messages could be converted to dev_dbg(), but that depends
on CONFIG_DYNAMIC_DEBUG and DEBUG, and we want most of these messages to
*always* be in the dmesg log.
Link: https://lore.kernel.org/lkml/1555733240-19875-1-git-send-email-mohankumar718@gmail.com
Signed-off-by: Mohan Kumar <mohankumar718@gmail.com>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use dev_printk() when possible. This makes messages more consistent with
other device-related messages and, in some cases, adds useful information.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
-----BEGIN PGP SIGNATURE-----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=WZfC
-----END PGP SIGNATURE-----
Merge tag 'printk-for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk
Pull printk updates from Petr Mladek:
- Allow state reset of printk_once() calls.
- Prevent crashes when dereferencing invalid pointers in vsprintf().
Only the first byte is checked for simplicity.
- Make vsprintf warnings consistent and inlined.
- Treewide conversion of obsolete %pf, %pF to %ps, %pF printf
modifiers.
- Some clean up of vsprintf and test_printf code.
* tag 'printk-for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk:
lib/vsprintf: Make function pointer_string static
vsprintf: Limit the length of inlined error messages
vsprintf: Avoid confusion between invalid address and value
vsprintf: Prevent crash when dereferencing invalid pointers
vsprintf: Consolidate handling of unknown pointer specifiers
vsprintf: Factor out %pO handler as kobject_string()
vsprintf: Factor out %pV handler as va_format()
vsprintf: Factor out %p[iI] handler as ip_addr_string()
vsprintf: Do not check address of well-known strings
vsprintf: Consistent %pK handling for kptr_restrict == 0
vsprintf: Shuffle restricted_pointer()
printk: Tie printk_once / printk_deferred_once into .data.once for reset
treewide: Switch printk users from %pf and %pF to %ps and %pS, respectively
lib/test_printf: Switch to bitmap_zalloc()
On ThinkPad P50 SKUs with an Nvidia Quadro M1000M instead of the M2000M
variant, the BIOS does not always reset the secondary Nvidia GPU during
reboot if the laptop is configured in Hybrid Graphics mode. The reason is
unknown, but the following steps and possibly a good bit of patience will
reproduce the issue:
1. Boot up the laptop normally in Hybrid Graphics mode
2. Make sure nouveau is loaded and that the GPU is awake
3. Allow the Nvidia GPU to runtime suspend itself after being idle
4. Reboot the machine, the more sudden the better (e.g. sysrq-b may help)
5. If nouveau loads up properly, reboot the machine again and go back to
step 2 until you reproduce the issue
This results in some very strange behavior: the GPU will be left in exactly
the same state it was in when the previously booted kernel started the
reboot. This has all sorts of bad side effects: for starters, this
completely breaks nouveau starting with a mysterious EVO channel failure
that happens well before we've actually used the EVO channel for anything:
nouveau 0000:01:00.0: disp: chid 0 mthd 0000 data 00000400 00001000 00000002
This causes a timeout trying to bring up the GR ctx:
nouveau 0000:01:00.0: timeout
WARNING: CPU: 0 PID: 12 at drivers/gpu/drm/nouveau/nvkm/engine/gr/ctxgf100.c:1547 gf100_grctx_generate+0x7b2/0x850 [nouveau]
Hardware name: LENOVO 20EQS64N0B/20EQS64N0B, BIOS N1EET82W (1.55 ) 12/18/2018
Workqueue: events_long drm_dp_mst_link_probe_work [drm_kms_helper]
...
nouveau 0000:01:00.0: gr: wait for idle timeout (en: 1, ctxsw: 0, busy: 1)
nouveau 0000:01:00.0: gr: wait for idle timeout (en: 1, ctxsw: 0, busy: 1)
nouveau 0000:01:00.0: fifo: fault 01 [WRITE] at 0000000000008000 engine 00 [GR] client 15 [HUB/SCC_NB] reason c4 [] on channel -1 [0000000000 unknown]
The GPU never manages to recover. Booting without loading nouveau causes
issues as well, since the GPU starts sending spurious interrupts that cause
other device's IRQs to get disabled by the kernel:
irq 16: nobody cared (try booting with the "irqpoll" option)
...
handlers:
[<000000007faa9e99>] i801_isr [i2c_i801]
Disabling IRQ #16
...
serio: RMI4 PS/2 pass-through port at rmi4-00.fn03
i801_smbus 0000:00:1f.4: Timeout waiting for interrupt!
i801_smbus 0000:00:1f.4: Transaction timeout
rmi4_f03 rmi4-00.fn03: rmi_f03_pt_write: Failed to write to F03 TX register (-110).
i801_smbus 0000:00:1f.4: Timeout waiting for interrupt!
i801_smbus 0000:00:1f.4: Transaction timeout
rmi4_physical rmi4-00: rmi_driver_set_irq_bits: Failed to change enabled interrupts!
This causes the touchpad and sometimes other things to get disabled.
Since this happens without nouveau, we can't fix this problem from nouveau
itself.
Add a PCI quirk for the specific P50 variant of this GPU. Make sure the
GPU is advertising NoReset- so we don't reset the GPU when the machine is
in Dedicated graphics mode (where the GPU being initialized by the BIOS is
normal and expected). Map the GPU MMIO space and read the magic 0x2240c
register, which will have bit 1 set if the device was POSTed during a
previous boot. Once we've confirmed all of this, reset the GPU and
re-disable it - bringing it back to a healthy state.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203003
Link: https://lore.kernel.org/lkml/20190212220230.1568-1-lyude@redhat.com
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: nouveau@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Cc: Karol Herbst <kherbst@redhat.com>
Cc: Ben Skeggs <skeggsb@gmail.com>
Cc: stable@vger.kernel.org
When using PCI passthrough with this device, the host machine locks up
completely when starting the VM, requiring a hard reboot. Add a quirk to
avoid bus resets on this device.
Fixes: c3e59ee4e7 ("PCI: Mark Atheros AR93xx to avoid bus reset")
Link: https://lore.kernel.org/linux-pci/20190107213248.3034-1-james.prestwood@linux.intel.com
Signed-off-by: James Prestwood <james.prestwood@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.14+
ATS is broken on the Radeon R7 GPU (at least for Stoney Ridge based laptop)
and causes IOMMU stalls and system failure. Disable ATS on these devices
to make them usable again with IOMMU enabled.
Thanks to Joerg Roedel <jroedel@suse.de> for help.
[bhelgaas: In the email thread mentioned below, Alex suspects the real
problem is in sbios or iommu, so it may affect only certain systems, and it
may affect other devices in those systems as well. However, per Joerg we
lack the ability to debug further, so this quirk is the best we can do for
now.]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=194521
Link: https://lore.kernel.org/lkml/20190408103725.30426-1-nickel@altlinux.org
Fixes: 9b44b0b09d ("PCI: Mark AMD Stoney GPU ATS as broken")
Signed-off-by: Nikolai Kostrigin <nickel@altlinux.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
CC: stable@vger.kernel.org
Due to an erratum in some Pericom PCIe-to-PCI bridges in reverse mode
(conventional PCI on primary side, PCIe on downstream side), the Retrain
Link bit needs to be cleared manually to allow the link training to
complete successfully.
If it is not cleared manually, the link training is continuously restarted
and no devices below the PCI-to-PCIe bridge can be accessed. That means
drivers for devices below the bridge will be loaded but won't work and may
even crash because the driver is only reading 0xffff.
See the Pericom Errata Sheet PI7C9X111SLB_errata_rev1.2_102711.pdf for
details. Devices known as affected so far are: PI7C9X110, PI7C9X111SL,
PI7C9X130.
Add a new flag, clear_retrain_link, in struct pci_dev. Quirks for affected
devices set this bit.
Note that pcie_retrain_link() lives in aspm.c because that's currently the
only place we use it, but this erratum is not specific to ASPM, and we may
retrain links for other reasons in the future.
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
[bhelgaas: apply regardless of CONFIG_PCIEASPM]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
CC: stable@vger.kernel.org
There is a Marvell 88SE9170 PCIe SATA controller I found on a board here.
Some quick testing with the ARM SMMU enabled reveals that it suffers from
the same requester ID mixup problems as the other Marvell chips listed
already.
Add the PCI vendor/device ID to the list of chips which need the
workaround.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org
-----BEGIN PGP SIGNATURE-----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=vf9L
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Use match_string() instead of reimplementing it (Andy Shevchenko)
- Enable SERR# forwarding for all bridges (Bharat Kumar Gogada)
- Use Latency Tolerance Reporting if already enabled by platform (Bjorn
Helgaas)
- Save/restore LTR info for suspend/resume (Bjorn Helgaas)
- Fix DPC use of uninitialized data (Dongdong Liu)
- Probe bridge window attributes only once at enumeration-time to fix
device accesses during rescan (Bjorn Helgaas)
- Return BAR size (not "size -1 ") from pci_size() to simplify code (Du
Changbin)
- Use config header type (not class code) identify bridges more
reliably (Honghui Zhang)
- Work around Intel Denverton incorrect Trace Hub BAR size reporting
(Alexander Shishkin)
- Reorder pciehp cached state/hardware state updates to avoid missed
interrupts (Mika Westerberg)
- Turn ibmphp semaphores into completions or mutexes (Arnd Bergmann)
- Mark expected switch fall-through (Mathieu Malaterre)
- Use of_node_name_eq() for node name comparisons (Rob Herring)
- Add ACS and pciehp quirks for HXT SD4800 (Shunyong Yang)
- Consolidate Rohm Vendor ID definitions (Andy Shevchenko)
- Use u32 (not __u32) for things not exposed to userspace (Logan
Gunthorpe)
- Fix locking semantics of bus and slot reset interfaces (Alex
Williamson)
- Update PCIEPORTBUS Kconfig help text (Hou Zhiqiang)
- Allow portdrv to claim subtractive decode Ports so PCIe services will
work for them (Honghui Zhang)
- Report PCIe links that become degraded at run-time (Alexandru
Gagniuc)
- Blacklist Gigabyte X299 Root Port power management to fix Thunderbolt
hotplug (Mika Westerberg)
- Revert runtime PM suspend/resume callbacks that broke PME on network
cable plug (Mika Westerberg)
- Disable Data Link State Changed interrupts to prevent wakeup
immediately after suspend (Mika Westerberg)
- Extend altera to support Stratix 10 (Ley Foon Tan)
- Allow building altera driver on ARM64 (Ley Foon Tan)
- Replace Douglas with Tom Joseph as Cadence PCI host/endpoint
maintainer (Lorenzo Pieralisi)
- Add DT support for R-Car RZ/G2E (R8A774C0) (Fabrizio Castro)
- Add dra72x/dra74x/dra76x SoC compatible strings (Kishon Vijay Abraham I)
- Enable x2 mode support for dra72x/dra74x/dra76x SoC (Kishon Vijay
Abraham I)
- Configure dra7xx PHY to PCIe mode (Kishon Vijay Abraham I)
- Simplify dwc (remove unnecessary header includes, name variables
consistently, reduce inverted logic, etc) (Gustavo Pimentel)
- Add i.MX8MQ support (Andrey Smirnov)
- Add message to help debug dwc MSI-X mask bit errors (Gustavo
Pimentel)
- Work around imx7d PCIe PLL erratum (Trent Piepho)
- Don't assert qcom reset GPIO during probe (Bjorn Andersson)
- Skip dwc MSI init if MSIs have been disabled (Lucas Stach)
- Use memcpy_fromio()/memcpy_toio() instead of plain memcpy() in PCI
endpoint framework (Wen Yang)
- Add interface to discover supported endpoint features to replace a
bitfield that wasn't flexible enough (Kishon Vijay Abraham I)
- Implement the new supported-feature interface for designware-plat,
dra7xx, rockchip, cadence (Kishon Vijay Abraham I)
- Fix issues with 64-bit BAR in endpoints (Kishon Vijay Abraham I)
- Add layerscape endpoint mode support (Xiaowei Bao)
- Remove duplicate struct hv_vp_set in favor of struct hv_vpset (Maya
Nakamura)
- Rework hv_irq_unmask() to use cpumask_to_vpset() instead of
open-coded reimplementation (Maya Nakamura)
- Align Hyper-V struct retarget_msi_interrupt arguments (Maya Nakamura)
- Fix mediatek MMIO size computation to enable full size of available
MMIO space (Honghui Zhang)
- Fix mediatek DMA window size computation to allow endpoint DMA access
to full DRAM address range (Honghui Zhang)
- Fix mvebu prefetchable BAR regression caused by common bridge
emulation that assumed all bridges had prefetchable windows (Thomas
Petazzoni)
- Make advk_pci_bridge_emul_ops static (Wei Yongjun)
- Configure MPS settings for VMD root ports (Jon Derrick)
* tag 'pci-v5.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (92 commits)
PCI: Update PCIEPORTBUS Kconfig help text
PCI: Fix "try" semantics of bus and slot reset
PCI/LINK: Report degraded links via link bandwidth notification
dt-bindings: PCI: altera: Add altr,pcie-root-port-2.0
PCI: altera: Enable driver on ARM64
PCI: altera: Add Stratix 10 PCIe support
PCI/PME: Fix possible use-after-free on remove
PCI: aardvark: Make symbol 'advk_pci_bridge_emul_ops' static
PCI: dwc: skip MSI init if MSIs have been explicitly disabled
PCI: hv: Refactor hv_irq_unmask() to use cpumask_to_vpset()
PCI: hv: Replace hv_vp_set with hv_vpset
PCI: hv: Add __aligned(8) to struct retarget_msi_interrupt
PCI: mediatek: Enlarge PCIe2AHB window size to support 4GB DRAM
PCI: mediatek: Fix memory mapped IO range size computation
PCI: dwc: Remove superfluous shifting in definitions
PCI: dwc: Make use of GENMASK/FIELD_PREP
PCI: dwc: Make use of BIT() in constant definitions
PCI: dwc: Share code for dw_pcie_rd/wr_other_conf()
PCI: dwc: Make use of IS_ALIGNED()
PCI: imx6: Add code to request/control "pcie_aux" clock for i.MX8MQ
...
There are at least four different parts with the same Vendor and Device
ID ([16c3:abcd]):
1) Synopsys HAPS USB3 controller
2) Synopsys PCIe Root Port in Freescale/NXP i.MX6Q (reported by Lucas)
3) Synopsys PCIe Root Port in Freescale/NXP i.MX6QP (reported by Lukas)
4) Synopsys PCIe Root Port in Freescale/NXP i.MX7D (reported by Trent)
The HAPS USB3 controller has a Class Code of PCI_CLASS_SERIAL_USB_XHCI,
which means the XHCI driver would normally claim it. Previously,
quirk_synopsys_haps() changed the Class Code of all [16c3:abcd] devices,
including the Root Ports, to PCI_CLASS_SERIAL_USB_DEVICE to prevent the
XHCI driver from claiming them so dwc3-haps can claim them instead.
Changing the Class Code of the Root Ports prevents the PCI core from
handling them as bridges, so devices below them don't work.
Restrict the quirk so it only changes the Class Code for devices that start
with the PCI_CLASS_SERIAL_USB_XHCI Class Code, leaving the Root Ports
alone.
Fixes: 03e6742584 ("PCI: Override Synopsys USB 3.x HAPS device class")
Reported-by: Lukas F. Hartmann <lukas@mntmn.com>
Reported-by: Trent Piepho <tpiepho@impinj.com>
Reported-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The design of HXT SD4800 ACS feature is the same as QCOM QDF2xxx. Add an
ACS quirk for the SD4800.
Signed-off-by: Shunyong Yang <shunyong.yang@hxt-semitech.com>
[bhelgaas: split to separate patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
CC: Joey Zheng <yu.zheng@hxt-semitech.com>
There is a plan to build the kernel with -Wimplicit-fallthrough and
these places in the code produced warnings (W=1). Fix them up.
Signed-off-by: Mathieu Malaterre <malat@debian.org>
[bhelgaas: squash into one patch, drop extra changelog detail]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Synopsys USB 3.x host HAPS platform has a class code of
PCI_CLASS_SERIAL_USB_XHCI, and xhci driver can claim it. However, these
devices should use dwc3-haps driver. Change these devices' class code to
PCI_CLASS_SERIAL_USB_DEVICE to prevent the xhci-pci driver from claiming
them.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Currently the Switchtec quirk runs on all endpoints in the switch,
including all the upstream and downstream ports. These other functions do
not contain BARs, so the quirk fails when trying to map the BAR and prints
the error "Cannot iomap Switchtec device". The user will see a few of
these useless and scary errors, one for each port in the switch.
At most, the quirk should only run on either a management endpoint
(PCI_CLASS_MEMORY_OTHER) or an NTB endpoint (PCI_CLASS_BRIDGE_OTHER).
However, the quirk is useless except in NTB applications, so we will
only run it when the class is PCI_CLASS_BRIDGE_OTHER.
Switch to using DECLARE_PCI_FIXUP_CLASS_FINAL and only match
PCI_CLASS_BRIDGE_OTHER.
Reported-by: Stephen Bates <sbates@raithlin.com>
Fixes: ad281ecf1c ("PCI: Add DMA alias quirk for Microsemi Switchtec NTB")
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
[bhelgaas: split SWITCHTEC_QUIRK() introduction to separate patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Doug Meyer <dmeyer@gigaio.com>
Cc: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Add SWITCHTEC_QUIRK() to reduce redundancy in declaring devices that use
quirk_switchtec_ntb_dma_alias().
By itself, this is no functional change, but a subsequent patch updates
SWITCHTEC_QUIRK() to fix ad281ecf1c ("PCI: Add DMA alias quirk for
Microsemi Switchtec NTB").
Fixes: ad281ecf1c ("PCI: Add DMA alias quirk for Microsemi Switchtec NTB")
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
[bhelgaas: split to separate patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add Device IDs to the Intel GPU "spurious interrupt" quirk table.
For these devices, unplugging the VGA cable and plugging it in again causes
spurious interrupts from the IGD. Linux eventually disables the interrupt,
but of course that disables any other devices sharing the interrupt.
The theory is that this is a VGA BIOS defect: it should have disabled the
IGD interrupt but failed to do so.
See f67fd55fa9 ("PCI: Add quirk for still enabled interrupts on Intel
Sandy Bridge GPUs") and 7c82126a94 ("PCI: Add new ID for Intel GPU
"spurious interrupt" quirk") for some history.
[bhelgaas: See link below for discussion about how to fix this more
generically instead of adding device IDs for every new Intel GPU. I hope
this is the last patch to add device IDs.]
Link: https://lore.kernel.org/linux-pci/1537974841-29928-1-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v3.4+
Remove a set but unused variable in quirks.c. Fixes warning:
variable ‘mmio_sys_info’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Joshua Abraham <j.abraham1776@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Allow the PCI quirk tables to be emitted in a way that avoids absolute
references to the hook functions. This reduces the size of the entries,
and, more importantly, makes them invariant under runtime relocation
(e.g., for KASLR)
Link: http://lkml.kernel.org/r/20180704083651.24360-6-ard.biesheuvel@linaro.org
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morris <james.morris@microsoft.com>
Cc: James Morris <jmorris@namei.org>
Cc: Jessica Yu <jeyu@kernel.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Nicolas Pitre <nico@linaro.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: "Serge E. Hallyn" <serge@hallyn.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Garnier <thgarnie@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Add more devices to Broadcom PAXC quirk (Ray Jui)
- Work around corrupted Broadcom PAXC config space to enable SMMU and
GICv3 ITS (Ray Jui)
- Disable MSI parsing to work around broken Broadcom PAXC logic in some
devices (Ray Jui)
- Hide unconfigured functions to work around a Broadcom PAXC defect (Ray
Jui)
- Lower iproc log level to reduce console output during boot (Ray Jui)
* remotes/lorenzo/pci/iproc:
PCI: iproc: Reduce inbound/outbound mapping print level
PCI: iproc: Reject unconfigured physical functions from PAXC
PCI: iproc: Disable MSI parsing in certain PAXC blocks
PCI: iproc: Fix up corrupted PAXC root complex config registers
PCI: iproc: Activate PAXC bridge quirk for more devices
- To avoid bus errors, enable PASID only if entire path supports End-End
TLP prefixes (Sinan Kaya)
- Unify slot and bus reset functions and remove hotplug knowledge from
callers (Sinan Kaya)
- Add Function-Level Reset quirks for Intel and Samsung NVMe devices to
fix guest reboot issues (Alex Williamson)
- Add function 1 DMA alias quirk for Marvell 88SS9183 PCIe SSD Controller
(Bjorn Helgaas)
* pci/virtualization:
PCI: Add function 1 DMA alias quirk for Marvell 88SS9183
PCI: Delay after FLR of Intel DC P3700 NVMe
PCI: Disable Samsung SM961/PM961 NVMe before FLR
PCI: Export pcie_has_flr()
PCI: Rename pci_try_reset_bus() to pci_reset_bus()
PCI: Deprecate pci_reset_bus() and pci_reset_slot() functions
PCI: Unify try slot and bus reset API
PCI: Hide pci_reset_bridge_secondary_bus() from drivers
IB/hfi1: Use pci_try_reset_bus() for initiating PCI Secondary Bus Reset
PCI: Handle error return from pci_reset_bridge_secondary_bus()
PCI/IOV: Tidy pci_sriov_set_totalvfs()
PCI: Enable PASID only if entire path supports End-End TLP prefixes
# Conflicts:
# drivers/pci/hotplug/pciehp_hpc.c
- Add DMA alias quirk for Microsemi Switchtec NTB (Doug Meyer)
- Expand documentation for pci_add_dma_alias() (Logan Gunthorpe)
* pci/switchtec:
PCI: Expand documentation for pci_add_dma_alias()
PCI: Add DMA alias quirk for Microsemi Switchtec NTB
switchtec: Use generic PCI Vendor ID and Class Code
# Conflicts:
# drivers/pci/quirks.c
- Add "pci=disable_acs_redir=" parameter to disable ACS redirection for
peer-to-peer DMA support (we don't have the peer-to-peer support yet;
this is just one piece) (Logan Gunthorpe)
* pci/peer-to-peer:
PCI: Add ACS Redirect disable quirk for Intel Sunrise Point
PCI: Add device-specific ACS Redirect disable infrastructure
PCI: Convert device-specific ACS quirks from NULL termination to ARRAY_SIZE
PCI: Add "pci=disable_acs_redir=" parameter for peer-to-peer support
PCI: Allow specifying devices using a base bus and path of devfns
PCI: Make specifying PCI devices in kernel parameters reusable
PCI: Hide ACS quirk declarations inside PCI core
- Mark fall-through switch cases before enabling -Wimplicit-fallthrough
(Gustavo A. R. Silva)
- Move DMA-debug PCI init from arch code to PCI core (Christoph Hellwig)
- Fix pci_request_irq() usage of IRQF_ONESHOT when no handler is supplied
(Heiner Kallweit)
- Unify PCI and DMA direction #defines (Shunyong Yang)
- Add PCI_DEVICE_DATA() macro (Andy Shevchenko)
- Check for VPD completion before checking for timeout (Bert Kenward)
- Limit Netronome NFP5000 config space size to work around erratum (Jakub
Kicinski)
* pci/misc:
PCI: Limit config space size for Netronome NFP5000
PCI/VPD: Check for VPD access completion before checking for timeout
PCI: Add PCI_DEVICE_DATA() macro to fully describe device ID entry
PCI: Unify PCI and normal DMA direction definitions
PCI: Use IRQF_ONESHOT if pci_request_irq() called with no handler
PCI: Call dma_debug_add_bus() for pci_bus_type from PCI core
PCI: Mark fall-through switch cases before enabling -Wimplicit-fallthrough
# Conflicts:
# drivers/pci/hotplug/pciehp_ctrl.c
Like the NFP4000 and NFP6000, the NFP5000 as an erratum where reading/
writing to PCI config space addresses above 0x600 can cause the NFP to
generate PCIe completion timeouts.
Limit the NFP5000's PF's config space size to 0x600 bytes as is already
done for the NFP4000 and NFP6000.
The NFP5000's VF is 0x6003 (PCI_DEVICE_ID_NETRONOME_NFP6000_VF), the same
device ID as the NFP6000's VF. Thus, its config space is already limited
by the existing use of quirk_nfp6000().
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tony Egan <tony.egan@netronome.com>
Intel Sunrise Point PCH hardware has an implementation of the ACS bits that
does not comply with the PCIe standard. Add a device-specific quirk,
pci_quirk_disable_intel_spt_pch_acs_redir() to disable ACS Redirection on
this system.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
[bhelgaas: changelog, split to separate patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Intel Sunrise Point (SPT) PCH hardware has an implementation of the ACS
bits that does not comply with the PCIe standard. To deal with this we
need device-specific quirks to disable ACS redirection.
Add a new pci_dev_specific_disable_acs_redir() quirk and a new
.disable_acs_redir() function pointer for use by non-compliant devices. No
functional change intended.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
[bhelgaas: split to separate patch, move
pci_dev_specific_disable_acs_redir() declarations to drivers/pci/pci.h]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Convert the search for device-specific ACS enable quirks from searching a
NULL-terminated array to iterating through the array, which is always
fixed-size anyway. No functional change intended.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
[bhelgaas: changelog, split to separate patch for reviewability]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Add a device-specific reset for Intel DC P3700 NVMe device which exhibits a
timeout failure in drivers waiting for the ready status to update after
NVMe enable if the driver interacts with the device too soon after FLR. As
this has been observed in device assignment scenarios, resolve this with a
device-specific reset quirk to add an additional, heuristically determined,
delay after the FLR completes.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1592654
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The Samsung SM961/PM961 (960 EVO) sometimes fails to return from FLR with
the PCI config space reading back as -1. A reproducible instance of this
behavior is resolved by clearing the enable bit in the NVMe configuration
register and waiting for the ready status to clear (disabling the NVMe
controller) prior to FLR.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1542494
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Activate PAXC bridge quirk for more PAXC based PCIe root complex with
the following PCIe device ID:
0xd750, 0xd802, 0xd804
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Warning level 2 was used: -Wimplicit-fallthrough=2
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Some IDT switches incorrectly flag an ACS Source Validation error on
completions for config read requests even though PCIe r4.0, sec 6.12.1.1,
says that completions are never affected by ACS Source Validation. Here's
the text of IDT 89H32H8G3-YC, erratum #36:
Item #36 - Downstream port applies ACS Source Validation to Completions
Section 6.12.1.1 of the PCI Express Base Specification 3.1 states that
completions are never affected by ACS Source Validation. However,
completions received by a downstream port of the PCIe switch from a
device that has not yet captured a PCIe bus number are incorrectly
dropped by ACS Source Validation by the switch downstream port.
Workaround: Issue a CfgWr1 to the downstream device before issuing the
first CfgRd1 to the device. This allows the downstream device to capture
its bus number; ACS Source Validation no longer stops completions from
being forwarded by the downstream port. It has been observed that
Microsoft Windows implements this workaround already; however, some
versions of Linux and other operating systems may not.
When doing the first config read to probe for a device, if the device is
behind an IDT switch with this erratum:
1. Disable ACS Source Validation if enabled
2. Wait for device to become ready to accept config accesses (by using
the Config Request Retry Status mechanism)
3. Do a config write to the endpoint
4. Enable ACS Source Validation (if it was enabled to begin with)
The workaround suggested by IDT is basically only step 3, but we don't know
when the device is ready to accept config requests. That means we need to
do config reads until we receive a non-Config Request Retry Status, which
means we need to disable ACS SV temporarily.
Signed-off-by: James Puthukattukaran <james.puthukattukaran@oracle.com>
[bhelgaas: changelog, clean up whitespace, fold in unused variable fix
from Anders Roxell <anders.roxell@linaro.org>]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Add a quirk for the Microsemi Switchtec parts to allow DMA access via
non-transparent bridging to work when the IOMMU is turned on.
This exclusively addresses the ability of a remote NT endpoint to perform
DMA accesses through the locally enumerated NT endpoint. Other aspects of
the Switchtec NTB functionality, such as interrupts for doorbells and
messages are independent of this quirk, and will work whether the IOMMU is
on or off.
When a requestor on one NT endpoint accesses memory on another NT endpoint,
it does this via a devfn proxy ID. Proxy IDs are statically assigned to
each NT endpoint by the NTB hardware as part of the release-from-reset
sequence prior to PCI enumeration. These proxy IDs cannot be modified
dynamically, and are not visible to the host during enumeration.
When the Switchtec NTB driver loads it will map local requestor IDs, such
as the root complex and transparent bridge DMA engines, to proxy IDs by
populating those requestor IDs in hardware mapping table table entries.
This establishes a fixed relationship between a requestor ID and a proxy
ID.
When a peer on a remote NT endpoint performs an access within a particular
translation window in it's NT endpoint BAR address space, that access is
translated to a DMA request on the local endpoint's bus. As part of the
translation process, the original requestor ID has its devfn replaced with
the proxy ID, and the bus portion of the BDF is replaced with the bus of
the local NT endpoint. Thus, the DMA access from a remote NT endpoint will
appear on the local bus to have come from the unknown devfn which the IOMMU
will reject.
Interrogate NTB hardware registers for each remote NT endpoint to obtain
the proxy IDs that have been assigned to it and alias them to the local
(enumerated) NT endpoint's device. The IOMMU then accepts the remote proxy
IDs as if they were requests coming directly from the enumerated endpoint,
giving remote requestors access to memory resources which the local host
has made available.
Note that the aliasing of the proxy IDs cannot be performed at the driver
level given the current IOMMU architecture. Superficially this is because
pci_add_dma_alias() symbol is not exported. Functionally, the current
IOMMU design requires the aliasing to be performed prior to the creation of
IOMMU groups. If a driver were to attempt to use pci_add_dma_alias() in
its probe routine it would fail since the IOMMU groups have been set up by
that time. If the Switchtec hardware supported dynamic proxy ID
(re-)assignment this would be an issue, but it does not.
To further clarify static proxy ID assignment: While the requester ID to
proxy ID mapping can be dynamically changed, the number and value of proxy
IDs given to an NT EP cannot, even for dynamic reconfiguration such as
hot-add. Therefore, the chip configuration must account a priori for the
proxy IDs needs, considering both static and dynamic system configurations.
For example, a port on the chip may not having anything plugged into it at
start of day; but it must have a sufficient number of proxy IDs assigned to
accommodate the supported devices which may be hot-added.
Switchtec NTB functionality with the IOMMU off is unchanged by this quirk.
Signed-off-by: Doug Meyer <dmeyer@gigaio.com>
[bhelgaas: use hard-coded Device IDs instead of adding #defines for each]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
- add generic enable function for simple SR-IOV hardware (Alexander
Duyck)
- use generic SR-IOV enable for ena, nvme (Alexander Duyck)
- add ACS quirk for Intel 7th & 8th Gen mobile (Alex Williamson)
- add ACS quirk for Intel 300 series (Mika Westerberg)
* pci/virtualization:
PCI/IOV: Allow PF drivers to limit total_VFs to 0
PCI: Add "pci=noats" boot parameter
PCI: Add ACS quirk for Intel 300 series
PCI: Add ACS quirk for Intel 7th & 8th Gen mobile
nvme-pci: Use pci_sriov_configure_simple() to enable VFs
net: ena: Use pci_sriov_configure_simple() to enable VFs
PCI/IOV: Add pci-pf-stub driver for PFs that only enable VFs
PCI/IOV: Add pci_sriov_configure_simple()
The infrastructure that applies PCI quirks was buried in the middle of the
quirks themselves (at one time it was probably at the end of the file, but
new quirks tend to be added at the end of the file). Move it all to the
top of the file so it's easy to find. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Intel 300 series chipset still has the same ACS issue as the previous
generations so extend the ACS quirk to cover it as well.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org
The specification update indicates these have the same errata for
implementing non-standard ACS capabilities.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org
Per PCIe r3.1, sec 2.2.6.2 and 7.8.4, a Requester may not use 8-bit Tags
unless its Extended Tag Field Enable is set, but all Receivers/Completers
must handle 8-bit Tags correctly regardless of their Extended Tag Field
Enable.
Some devices do not handle 8-bit Tags as Completers, so add a quirk for
them. If we find such a device, we disable Extended Tags for the entire
hierarchy to make peer-to-peer DMA possible.
The Broadcom HT1100/HT2000/HT2100 seems to have issues with handling 8-bit
tags. Mark it as broken.
This fixes Xorg hangs and unresponsive keyboards with errors like this:
radeon 0000:06:00.0: GPU lockup (current fence id 0x000000000000000e last fence id 0x0000000000000
[drm:r600_ring_test [radeon]] *ERROR* radeon: ring 0 test failed (scratch(0x8504)=0xCAFEDEAD)
[drm:r600_resume [radeon]] *ERROR* r600 startup failed on resume
Fixes: 60db3a4d8c ("PCI: Enable PCIe Extended Tags if supported")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=196197
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
CC: stable@vger.kernel.org # v4.11: 62ce94a7a5 PCI: Mark Broadcom HT2100 Root Port Extended Tags as broken
CC: stable@vger.kernel.org # v4.11
-----BEGIN PGP SIGNATURE-----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=T++R
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- move pci_uevent_ers() out of pci.h (Michael Ellerman)
- skip ASPM common clock warning if BIOS already configured it (Sinan
Kaya)
- fix ASPM Coverity warning about threshold_ns (Gustavo A. R. Silva)
- remove last user of pci_get_bus_and_slot() and the function itself
(Sinan Kaya)
- add decoding for 16 GT/s link speed (Jay Fang)
- add interfaces to get max link speed and width (Tal Gilboa)
- add pcie_bandwidth_capable() to compute max supported link bandwidth
(Tal Gilboa)
- add pcie_bandwidth_available() to compute bandwidth available to
device (Tal Gilboa)
- add pcie_print_link_status() to log link speed and whether it's
limited (Tal Gilboa)
- use PCI core interfaces to report when device performance may be
limited by its slot instead of doing it in each driver (Tal Gilboa)
- fix possible cpqphp NULL pointer dereference (Shawn Lin)
- rescan more of the hierarchy on ACPI hotplug to fix Thunderbolt/xHCI
hotplug (Mika Westerberg)
- add support for PCI I/O port space that's neither directly accessible
via CPU in/out instructions nor directly mapped into CPU physical
memory space. This is fairly intrusive and includes minor changes to
interfaces used for I/O space on most platforms (Zhichang Yuan, John
Garry)
- add support for HiSilicon Hip06/Hip07 LPC I/O space (Zhichang Yuan,
John Garry)
- use PCI_EXP_DEVCTL2_COMP_TIMEOUT in rapidio/tsi721 (Bjorn Helgaas)
- remove possible NULL pointer dereference in of_pci_bus_find_domain_nr()
(Shawn Lin)
- report quirk timings with dev_info (Bjorn Helgaas)
- report quirks that take longer than 10ms (Bjorn Helgaas)
- add and use Altera Vendor ID (Johannes Thumshirn)
- tidy Makefiles and comments (Bjorn Helgaas)
- don't set up INTx if MSI or MSI-X is enabled to align cris, frv,
ia64, and mn10300 with x86 (Bjorn Helgaas)
- move pcieport_if.h to drivers/pci/pcie/ to encapsulate it (Frederick
Lawler)
- merge pcieport_if.h into portdrv.h (Bjorn Helgaas)
- move workaround for BIOS PME issue from portdrv to PCI core (Bjorn
Helgaas)
- completely disable portdrv with "pcie_ports=compat" (Bjorn Helgaas)
- remove portdrv link order dependency (Bjorn Helgaas)
- remove support for unused VC portdrv service (Bjorn Helgaas)
- simplify portdrv feature permission checking (Bjorn Helgaas)
- remove "pcie_hp=nomsi" parameter (use "pci=nomsi" instead) (Bjorn
Helgaas)
- remove unnecessary "pcie_ports=auto" parameter (Bjorn Helgaas)
- use cached AER capability offset (Frederick Lawler)
- don't enable DPC if BIOS hasn't granted AER control (Mika Westerberg)
- rename pcie-dpc.c to dpc.c (Bjorn Helgaas)
- use generic pci_mmap_resource_range() instead of powerpc and xtensa
arch-specific versions (David Woodhouse)
- support arbitrary PCI host bridge offsets on sparc (Yinghai Lu)
- remove System and Video ROM reservations on sparc (Bjorn Helgaas)
- probe for device reset support during enumeration instead of runtime
(Bjorn Helgaas)
- add ACS quirk for Ampere (née APM) root ports (Feng Kan)
- add function 1 DMA alias quirk for Marvell 88SE9220 (Thomas
Vincent-Cross)
- protect device restore with device lock (Sinan Kaya)
- handle failure of FLR gracefully (Sinan Kaya)
- handle CRS (config retry status) after device resets (Sinan Kaya)
- skip various config reads for SR-IOV VFs as an optimization
(KarimAllah Ahmed)
- consolidate VPD code in vpd.c (Bjorn Helgaas)
- add Tegra dependency on PCI_MSI_IRQ_DOMAIN (Arnd Bergmann)
- add DT support for R-Car r8a7743 (Biju Das)
- fix a PCI_EJECT vs PCI_BUS_RELATIONS race condition in Hyper-V host
bridge driver that causes a general protection fault (Dexuan Cui)
- fix Hyper-V host bridge hang in MSI setup on 1-vCPU VMs with SR-IOV
(Dexuan Cui)
- fix Hyper-V host bridge hang when ejecting a VF before setting up MSI
(Dexuan Cui)
- make several structures static (Fengguang Wu)
- increase number of MSI IRQs supported by Synopsys DesignWare bridges
from 32 to 256 (Gustavo Pimentel)
- implemented multiplexed IRQ domain API and remove obsolete MSI IRQ
API from DesignWare drivers (Gustavo Pimentel)
- add Tegra power management support (Manikanta Maddireddy)
- add Tegra loadable module support (Manikanta Maddireddy)
- handle 64-bit BARs correctly in endpoint support (Niklas Cassel)
- support optional regulator for HiSilicon STB (Shawn Guo)
- use regulator bulk API for Qualcomm apq8064 (Srinivas Kandagatla)
- support power supplies for Qualcomm msm8996 (Srinivas Kandagatla)
* tag 'pci-v4.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (123 commits)
MAINTAINERS: Add John Garry as maintainer for HiSilicon LPC driver
HISI LPC: Add ACPI support
ACPI / scan: Do not enumerate Indirect IO host children
ACPI / scan: Rename acpi_is_serial_bus_slave() for more general use
HISI LPC: Support the LPC host on Hip06/Hip07 with DT bindings
of: Add missing I/O range exception for indirect-IO devices
PCI: Apply the new generic I/O management on PCI IO hosts
PCI: Add fwnode handler as input param of pci_register_io_range()
PCI: Remove __weak tag from pci_register_io_range()
MAINTAINERS: Add missing /drivers/pci/cadence directory entry
fm10k: Report PCIe link properties with pcie_print_link_status()
net/mlx5e: Use pcie_bandwidth_available() to compute bandwidth
net/mlx5: Report PCIe link properties with pcie_print_link_status()
net/mlx4_core: Report PCIe link properties with pcie_print_link_status()
PCI: Add pcie_print_link_status() to log link speed and whether it's limited
PCI: Add pcie_bandwidth_available() to compute bandwidth available to device
misc: pci_endpoint_test: Handle 64-bit BARs properly
PCI: designware-ep: Make dw_pcie_ep_reset_bar() handle 64-bit BARs properly
PCI: endpoint: Make sure that BAR_5 does not have 64-bit flag set when clearing
PCI: endpoint: Make epc->ops->clear_bar()/pci_epc_clear_bar() take struct *epf_bar
...
- probe for device reset support during enumeration instead of runtime
(Bjorn Helgaas)
- add ACS quirk for Ampere (née APM) root ports (Feng Kan)
- add function 1 DMA alias quirk for Marvell 88SE9220 (Thomas
Vincent-Cross)
- protect device restore with device lock (Sinan Kaya)
- handle failure of FLR gracefully (Sinan Kaya)
- handle CRS (config retry status) after device resets (Sinan Kaya)
- skip various config reads for SR-IOV VFs as an optimization (KarimAllah
Ahmed)
* pci/virtualization:
PCI/IOV: Add missing prototypes for powerpc pcibios interfaces
PCI/IOV: Use VF0 cached config registers for other VFs
PCI/IOV: Skip BAR sizing for VFs
PCI/IOV: Skip INTx config reads for VFs
PCI: Wait for device to become ready after secondary bus reset
PCI: Add a return type for pci_reset_bridge_secondary_bus()
PCI: Wait for device to become ready after a power management reset
PCI: Rename pci_flr_wait() to pci_dev_wait() and make it generic
PCI: Handle FLR failure and allow other reset types
PCI: Protect restore with device lock to be consistent
PCI: Add function 1 DMA alias quirk for Marvell 88SE9220
PCI: Add ACS quirk for Ampere root ports
PCI: Remove redundant probes for device reset support
PCI: Probe for device reset support during enumeration
Conflicts:
include/linux/pci.h
This removes the entire architecture code for blackfin, cris, frv, m32r,
metag, mn10300, score, and tile, including the associated device drivers.
I have been working with the (former) maintainers for each one to ensure
that my interpretation was right and the code is definitely unused in
mainline kernels. Many had fond memories of working on the respective
ports to start with and getting them included in upstream, but also saw
no point in keeping the port alive without any users.
In the end, it seems that while the eight architectures are extremely
different, they all suffered the same fate: There was one company
in charge of an SoC line, a CPU microarchitecture and a software
ecosystem, which was more costly than licensing newer off-the-shelf
CPU cores from a third party (typically ARM, MIPS, or RISC-V). It seems
that all the SoC product lines are still around, but have not used the
custom CPU architectures for several years at this point. In contrast,
CPU instruction sets that remain popular and have actively maintained
kernel ports tend to all be used across multiple licensees.
The removal came out of a discussion that is now documented at
https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
marking any ports as deprecated but remove them all at once after I made
sure that they are all unused. Some architectures (notably tile, mn10300,
and blackfin) are still being shipped in products with old kernels,
but those products will never be updated to newer kernel releases.
After this series, we still have a few architectures without mainline
gcc support:
- unicore32 and hexagon both have very outdated gcc releases, but the
maintainers promised to work on providing something newer. At least
in case of hexagon, this will only be llvm, not gcc.
- openrisc, risc-v and nds32 are still in the process of finishing their
support or getting it added to mainline gcc in the first place.
They all have patched gcc-7.3 ports that work to some degree, but
complete upstream support won't happen before gcc-8.1. Csky posted
their first kernel patch set last week, their situation will be similar.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fQ8z
-----END PGP SIGNATURE-----
Merge tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pul removal of obsolete architecture ports from Arnd Bergmann:
"This removes the entire architecture code for blackfin, cris, frv,
m32r, metag, mn10300, score, and tile, including the associated device
drivers.
I have been working with the (former) maintainers for each one to
ensure that my interpretation was right and the code is definitely
unused in mainline kernels. Many had fond memories of working on the
respective ports to start with and getting them included in upstream,
but also saw no point in keeping the port alive without any users.
In the end, it seems that while the eight architectures are extremely
different, they all suffered the same fate: There was one company in
charge of an SoC line, a CPU microarchitecture and a software
ecosystem, which was more costly than licensing newer off-the-shelf
CPU cores from a third party (typically ARM, MIPS, or RISC-V). It
seems that all the SoC product lines are still around, but have not
used the custom CPU architectures for several years at this point. In
contrast, CPU instruction sets that remain popular and have actively
maintained kernel ports tend to all be used across multiple licensees.
[ See the new nds32 port merged in the previous commit for the next
generation of "one company in charge of an SoC line, a CPU
microarchitecture and a software ecosystem" - Linus ]
The removal came out of a discussion that is now documented at
https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
marking any ports as deprecated but remove them all at once after I
made sure that they are all unused. Some architectures (notably tile,
mn10300, and blackfin) are still being shipped in products with old
kernels, but those products will never be updated to newer kernel
releases.
After this series, we still have a few architectures without mainline
gcc support:
- unicore32 and hexagon both have very outdated gcc releases, but the
maintainers promised to work on providing something newer. At least
in case of hexagon, this will only be llvm, not gcc.
- openrisc, risc-v and nds32 are still in the process of finishing
their support or getting it added to mainline gcc in the first
place. They all have patched gcc-7.3 ports that work to some
degree, but complete upstream support won't happen before gcc-8.1.
Csky posted their first kernel patch set last week, their situation
will be similar
[ Palmer Dabbelt points out that RISC-V support is in mainline gcc
since gcc-7, although gcc-7.3.0 is the recommended minimum - Linus ]"
This really says it all:
2498 files changed, 95 insertions(+), 467668 deletions(-)
* tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (74 commits)
MAINTAINERS: UNICORE32: Change email account
staging: iio: remove iio-trig-bfin-timer driver
tty: hvc: remove tile driver
tty: remove bfin_jtag_comm and hvc_bfin_jtag drivers
serial: remove tile uart driver
serial: remove m32r_sio driver
serial: remove blackfin drivers
serial: remove cris/etrax uart drivers
usb: Remove Blackfin references in USB support
usb: isp1362: remove blackfin arch glue
usb: musb: remove blackfin port
usb: host: remove tilegx platform glue
pwm: remove pwm-bfin driver
i2c: remove bfin-twi driver
spi: remove blackfin related host drivers
watchdog: remove bfin_wdt driver
can: remove bfin_can driver
mmc: remove bfin_sdh driver
input: misc: remove blackfin rotary driver
input: keyboard: remove bf54x driver
...
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJauCZfAAoJEHm+PkMAQRiGWGUH/2rhdQDkoJpYWnjaQkolECG8
MxpGE7nmIIHxQcbSDdHTGJ8IhVm6Z5wZ7ym/PwCDTT043Y1y341sJrIwL2/nTG6d
HVidk8hFvgN6QzlzVAHT3ZZMII/V9Zt+VV5SUYLGnPAVuJNHo/6uzWlTU5g+NTFo
IquFDdQUaGBlkKqby+NoAFnkV1UAIkW0g22cfvPnlO5GMer0gusGyVNvVp7TNj3C
sqj4Hvt3RMDLMNe9RZ2pFTiOD096n8FWpYftZneUTxFImhRV3Jg5MaaYZm9SI3HW
tXrv/LChT/F1mi5Pkx6tkT5Hr8WvcrwDMJ4It1kom10RqWAgjxIR3CMm448ileY=
=YKUG
-----END PGP SIGNATURE-----
Backmerge tag 'v4.16-rc7' into drm-next
Linux 4.16-rc7
This was requested by Daniel, and things were getting
a bit hard to reconcile, most of the conflicts were
trivial though.
Pull libata fixes from Tejun Heo:
"I sat on them too long and it's quite a few this late, but nothing has
a wide blast area. The changes are...
- Fix corner cases in SG command handling.
- Recent introduction of default powersaving mode config option
exposed several devices with broken powersaving behaviors. A number
of patches to update the blacklist accordingly.
- Fix a kernel panic on SAS hotplug.
- Other misc and device specific updates"
* 'for-4.16-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: Modify quirks for MX100 to limit NCQ_TRIM quirk to MU01 version
libata: Make Crucial BX100 500GB LPM quirk apply to all firmware versions
libata: Apply NOLPM quirk to Crucial M500 480 and 960GB SSDs
libata: Enable queued TRIM for Samsung SSD 860
PCI: Add function 1 DMA alias quirk for Highpoint RocketRAID 644L
ahci: Add PCI-id for the Highpoint Rocketraid 644L card
ata: do not schedule hot plug if it is a sas host
libata: disable LPM for Crucial BX100 SSD 500GB drive
libata: Apply NOLPM quirk to Crucial MX100 512GB SSDs
libata: update documentation for sysfs interfaces
ata: sata_rcar: Remove unused variable in sata_rcar_init_controller()
libata: transport: cleanup documentation of sysfs interface
sata_rcar: Reset SATA PHY when Salvator-X board resumes
libata: don't try to pass through NCQ commands to non-NCQ devices
libata: remove WARN() for DMA or PIO command without data
libata: fix length validation of ATAPI-relayed SCSI commands
ata: libahci: fix comment indentation
ahci: Add check for device presence (PCIe hot unplug) in ahci_stop_engine()
libata: Fix compile warning with ATA_DEBUG enabled
Remove pointless comments that tell us the file name, remove blank line
comments, follow multi-line comment conventions. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
With "initcall_debug", we report how long every PCI quirk took.
Even without "initcall_debug", report the runtime of any quirk that takes
longer than 10ms. This is to make it easier to notice quirks that slow
down boot.
This was motivated by a report from Paul Menzel that PCI final quirks took
half a second at boot.
Link: https://lkml.kernel.org/r/44cada166e42007d27b4c3e3aa0744d7@molgen.mpg.de
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
With "initcall_debug", we report how long every PCI quirk took. Previously
we used pr_debug(), which means you have to figure out how to enable debug
output.
Log these timings using pci_info() instead so it doesn't depend on DEBUG,
CONFIG_DYNAMIC_DEBUG, etc.
Also, don't log anything at all unless "initcall_debug" is specified. This
matches what we do in do_one_initcall_debug().
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move the VPD-related quirks from quirks.c to vpd.c, which removes the need
for struct pci_vpd outside vpd.c. The goal is to encapsulate all the VPD
code and structures in vpd.c.
No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The Tile architecture port was added by Chris Metcalf in 2010, and
maintained until early 2018 when he orphaned it due to his departure
from Mellanox, and nobody else stepped up to maintain it. The product
line is still around in the form of the BlueField SoC, but no longer
uses the Tile architecture.
There are also still products for sale with Tile-GX SoCs, notably the
Mikrotik CCR router family. The products all use old (linux-3.3) kernels
with lots of patches and won't be upgraded by their manufacturers. There
have been efforts to port both OpenWRT and Debian to these, but both
projects have stalled and are very unlikely to be continued in the future.
Given that we are reasonably sure that nobody is still using the port
with an upstream kernel any more, it seems better to remove it now while
the port is in a good shape than to let it bitrot for a few years first.
Cc: Chris Metcalf <chris.d.metcalf@gmail.com>
Cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Link: http://www.mellanox.com/page/npu_multicore_overview
Link: https://jenkins.debian.net/view/rebootstrap/job/rebootstrap_tilegx_gcc7/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Back in 2013, runtime PM for GPUs with integrated HDA controller was
introduced with commits 0d69704ae3 ("gpu/vga_switcheroo: add driver
control power feature. (v3)") and 246efa4a07 ("snd/hda: add runtime
suspend/resume on optimus support (v4)").
Briefly, the idea was that the HDA controller is forced on and off in
unison with the GPU.
The original code is mostly still in place even though it was never a
100% perfect solution: E.g. on access to the HDA controller, the GPU
is powered up via vga_switcheroo_runtime_resume_hdmi_audio() but there
are no provisions to keep it resumed until access to the HDA controller
has ceased: The GPU autosuspends after 5 seconds, rendering the HDA
controller inaccessible.
Additionally, a kludge is required when hda_intel.c probes: It has to
check whether the GPU is powered down (check_hdmi_disabled()) and defer
probing if so.
However in the meantime (in v4.10) the driver core has gained a feature
called device links which promises to solve such issues in a clean way:
It allows us to declare a dependency from the HDA controller (consumer)
to the GPU (supplier). The PM core then automagically ensures that the
GPU is runtime resumed as long as the HDA controller's ->probe hook is
executed and whenever the HDA controller is accessed.
By default, the HDA controller has a dependency on its parent, a PCIe
Root Port. Adding a device link creates another dependency on its
sibling:
PCIe Root Port
^ ^
| |
| |
HDA ===> GPU
The device link is not only used for runtime PM, it also guarantees that
on system sleep, the HDA controller suspends before the GPU and resumes
after the GPU, and on system shutdown the HDA controller's ->shutdown
hook is executed before the one of the GPU. It is a complete solution.
Using this functionality is as simple as calling device_link_add(),
which results in a dmesg entry like this:
pci 0000:01:00.1: Linked as a consumer to 0000:01:00.0
The code for the GPU-governed audio power management can thus be removed
(except where it's still needed for legacy manual power control).
The device link is added in a PCI quirk rather than in hda_intel.c.
It is therefore legal for the GPU to runtime suspend to D3cold even if
the HDA controller is not bound to a driver or if CONFIG_SND_HDA_INTEL
is not enabled, for accesses to the HDA controller will cause the GPU to
wake up regardless if they're occurring outside of hda_intel.c (think
config space readout via sysfs).
Contrary to the previous implementation, the HDA controller's power
state is now self-governed, rather than GPU-governed, whereas the GPU's
power state is no longer fully self-governed. (The HDA controller needs
to runtime suspend before the GPU can.)
It is thus crucial that runtime PM is always activated on the HDA
controller even if CONFIG_SND_HDA_POWER_SAVE_DEFAULT is set to 0 (which
is the default), lest the GPU stays awake. This is achieved by setting
the auto_runtime_pm flag on every codec and the AZX_DCAPS_PM_RUNTIME
flag on the HDA controller.
A side effect is that power consumption might be reduced if the GPU is
in use but the HDA controller is not, because the HDA controller is now
allowed to go to D3hot. Before, it was forced to stay in D0 as long as
the GPU was in use. (There is no reduction in power consumption on my
Nvidia GK107, but there might be on other chips.)
The code paths for legacy manual power control are adjusted such that
runtime PM is disabled during power off, thereby preventing the PM core
from resuming the HDA controller.
Note that the device link is not only added on vga_switcheroo capable
systems, but for *any* GPU with integrated HDA controller. The idea is
that the HDA controller streams audio via connectors located on the GPU,
so the GPU needs to be on for the HDA controller to do anything useful.
This commit implicitly fixes an unbalanced runtime PM ref upon unbind of
hda_intel.c: On ->probe, a runtime PM ref was previously released under
the condition "azx_has_pm_runtime(chip) || hda->use_vga_switcheroo", but
on ->remove a runtime PM ref was only acquired under the first of those
conditions. Thus, binding and unbinding the driver twice on a
vga_switcheroo capable system caused the runtime PM refcount to drop
below zero. The issue is resolved because the AZX_DCAPS_PM_RUNTIME flag
is now always set if use_vga_switcheroo is true.
For more information on device links please refer to:
https://www.kernel.org/doc/html/latest/driver-api/device_link.html
Documentation/driver-api/device_link.rst
Cc: Dave Airlie <airlied@redhat.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Peter Wu <peter@lekensteyn.nl>
Tested-by: Kai Heng Feng <kai.heng.feng@canonical.com> # AMD PowerXpress
Tested-by: Mike Lothian <mike@fireburn.co.uk> # AMD PowerXpress
Tested-by: Denis Lisov <dennis.lissov@gmail.com> # Nvidia Optimus
Tested-by: Peter Wu <peter@lekensteyn.nl> # Nvidia Optimus
Tested-by: Lukas Wunner <lukas@wunner.de> # MacBook Pro
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://patchwork.freedesktop.org/patch/msgid/51bd38360ff502a8c42b1ebf4405ee1d3f27118d.1520068884.git.lukas@wunner.de
The Highpoint RocketRAID 644L uses a Marvel 88SE9235 controller, as with
other Marvel controllers this needs a function 1 DMA alias quirk.
Note the RocketRAID 642L uses the same Marvel 88SE9235 controller and
already is listed with a function 1 DMA alias quirk.
Cc: stable@vger.kernel.org
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1534106
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add Marvell 88SE9220 DMA quirk as found and tested on bug 42679.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=42679
Signed-off-by: Thomas Vincent-Cross <me@tvc.id.au>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
The Ampere Computing PCIe root port does not support ACS at this point.
However, the hardware provides isolation and source validation through the
SMMU. The stream ID generated by the PCIe ports contain both the
bus/device/function number as well as the port ID in its 3 most significant
bits. Turn on ACS but disable all the peer-to-peer features.
APM is being rebranded to Ampere. The Vendor and Device IDs change, but
the functionality stays the same.
Signed-off-by: Feng Kan <fkan@apm.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
We've run into a problem where our device is attached
to a Virtual Machine and the use of the new pci_set_vpd_size()
API doesn't help. The VM kernel has been informed that
the accesses are okay, but all of the actual VPD Capability
Accesses are trapped down into the KVM Hypervisor where it
goes ahead and imposes the silent denials.
The right idea is to follow the kernel.org
commit 1c7de2b4ff ("PCI: Enable access to non-standard VPD for
Chelsio devices (cxgb3)") which Alexey Kardashevskiy authored
to establish a PCI Quirk for our T3-based adapters. This commit
extends that PCI Quirk to cover Chelsio T4 devices and later.
The advantage of this approach is that the VPD Size gets set early
in the Base OS/Hypervisor Boot and doesn't require that the cxgb4
driver even be available in the Base OS/Hypervisor. Thus PF4 can
be exported to a Virtual Machine and everything should work.
Fixes: 67e658794c ("cxgb4: Set VPD size so we can read both VPD structures")
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* pci/virtualization:
PCI: Expose ari_enabled in sysfs
PCI: Add function 1 DMA alias quirk for Marvell 9128
PCI: Mark Ceton InfiniTV4 INTx masking as broken
xen/pci: Use acpi_noirq_set() helper to avoid #ifdef
* pci/misc:
PCI: Add dummy pci_irqd_intx_xlate() for CONFIG_PCI=n build
PCI: Add wrappers for dev_printk()
PCI: Remove unnecessary messages for memory allocation failures
PCI: Add #defines for Completion Timeout Disable feature
hinic: Replace PCI pool old API
net: e100: Replace PCI pool old API
block: DAC960: Replace PCI pool old API
MAINTAINERS: Include more PCI files
PCI: Remove unneeded kallsyms include
powerpc/pci: Unroll two pass loop when scanning bridges
powerpc/pci: Use for_each_pci_bridge() helper
Add PCI-specific dev_printk() wrappers and use them to simplify the code
slightly. No functional change intended.
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
[bhelgaas: squash into one patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_get_bus_and_slot() is restrictive such that it assumes domain=0 as
where a PCI device is present. This restricts the device drivers to be
reused for other domain numbers.
Getting ready to remove pci_get_bus_and_slot() function in favor of
pci_get_domain_bus_and_slot().
When we have a pci_dev, extract the domain number from it.
The config access syscalls don't allow the user to supply a domain number,
so they only work on devices in domain 0, so we can just hard-code that.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
[bhelgaas: squash quirk & syscall patches together]
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
The Marvell 9128 is the original device generating bug 42679, from which
many other Marvell DMA alias quirks have been sourced, but we didn't have
positive confirmation of the fix on 9128 until now.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=42679
Link: https://www.spinics.net/lists/kvm/msg161459.html
Reported-by: Binarus <lists@binarus.de>
Tested-by: Binarus <lists@binarus.de>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
HiSilicon Hip06/Hip07 can operate as either a Root Port or an Endpoint. It
always advertises an MSI capability, but it can only generate MSIs when in
Endpoint mode.
The device has the same Vendor and Device IDs in both modes, so check the
Class Code and disable MSI only when operating as a Root Port.
[bhelgaas: changelog]
Fixes: 72f2ff0deb ("PCI: Disable MSI for HiSilicon Hip06/Hip07 Root Ports")
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
Cc: stable@vger.kernel.org # v4.11+
PCI_COMMAND_INTX_DISABLE is writable on the Ceton InfiniTV4, indicating
that the device supports disabling the INTx# signal, but it apparently
doesn't work.
Mark the device so we know we can't use PCI_COMMAND_INTX_DISABLE to disable
its interrupts.
Link: https://lkml.kernel.org/r/92a65068-60b2-c1a8-9e17-ac41fe3c5c93@code.jackst.com
Reported-by: John Strader <strader.john@code.jackst.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The file was converted from print_fn_descriptor_symbol() to %pF some time
ago (c9bbb4abb6 "PCI: use %pF instead of print_fn_descriptor_symbol()
in quirks.c"). kallsyms does not seem to be needed anymore.
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/host-thunder:
PCI: Avoid slot reset if bridge itself is broken
PCI: Avoid bus reset if bridge itself is broken
PCI: Mark Cavium CN8xxx to avoid bus reset
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Freescale PCIe controller advertises the MSI/MSI-X capability in both
RC and Endpoint mode, but in RC mode it doesn't support MSI/MSI-X by
itself; it can only transfer MSI/MSI-X from downstream devices.
Add a quirk to prevent use of MSI/MSI-X in RC mode.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Minghuan Lian <minghuan.Lian@nxp.com>
Extend the Cavium ThunderX ACS quirk to cover more device IDs and restrict
it to only Root Ports.
Signed-off-by: Vadim Lomovtsev <Vadim.Lomovtsev@cavium.com>
[bhelgaas: changelog, stable tag]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v4.12+
The Cavium ThunderX (CN8XXX) family of PCIe Root Ports does not advertise
an ACS capability. However, the RTL internally implements similar
protection as if ACS had Request Redirection, Completion Redirection,
Source Validation, and Upstream Forwarding features enabled.
Change Cavium ACS capabilities quirk flags accordingly.
Fixes: b404bcfbf0 ("PCI: Add ACS quirk for all Cavium devices")
Signed-off-by: Vadim Lomovtsev <Vadim.Lomovtsev@cavium.com>
[bhelgaas: tidy changelog, comment, stable tag]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v4.6+: b77d537d00d0: PCI: Apply Cavium ACS quirk only to CN81xx/CN83xx/CN88xx devices
Root ports of cn8xxx do not function after bus reset when used with some
e1000e and LSI HBA devices. Add a quirk to prevent bus reset on these root
ports.
Signed-off-by: David Daney <david.daney@cavium.com>
[jglauber@cavium.com: fixed typo and whitespaces]
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
... and __initconst if applicable.
Based on similar work for an older kernel in the Grsecurity patch.
[JD: fix toshiba-wmi build]
[JD: add htcpen]
[JD: move __initconst where checkscript wants it]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9cLP
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.14-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- add enhanced Downstream Port Containment support, which prints more
details about Root Port Programmed I/O errors (Dongdong Liu)
- add Layerscape ls1088a and ls2088a support (Hou Zhiqiang)
- add MediaTek MT2712 and MT7622 support (Ryder Lee)
- add MediaTek MT2712 and MT7622 MSI support (Honghui Zhang)
- add Qualcom IPQ8074 support (Varadarajan Narayanan)
- add R-Car r8a7743/5 device tree support (Biju Das)
- add Rockchip per-lane PHY support for better power management (Shawn
Lin)
- fix IRQ mapping for hot-added devices by replacing the
pci_fixup_irqs() boot-time design with a host bridge hook called at
probe-time (Lorenzo Pieralisi, Matthew Minter)
- fix race when enabling two devices that results in upstream bridge
not being enabled correctly (Srinath Mannam)
- fix pciehp power fault infinite loop (Keith Busch)
- fix SHPC bridge MSI hotplug events by enabling bus mastering
(Aleksandr Bezzubikov)
- fix a VFIO issue by correcting PCIe capability sizes (Alex
Williamson)
- fix an INTD issue on Xilinx and possibly other drivers by unifying
INTx IRQ domain support (Paul Burton)
- avoid IOMMU stalls by marking AMD Stoney GPU ATS as broken (Joerg
Roedel)
- allow APM X-Gene device assignment to guests by adding an ACS quirk
(Feng Kan)
- fix driver crashes by disabling Extended Tags on Broadcom HT2100
(Extended Tags support is required for PCIe Receivers but not
Requesters, and we now enable them by default when Requesters support
them) (Sinan Kaya)
- fix MSIs for devices that use phantom RIDs for DMA by assuming MSIs
use the real Requester ID (not a phantom RID) (Robin Murphy)
- prevent assignment of Intel VMD children to guests (which may be
supported eventually, but isn't yet) by not associating an IOMMU with
them (Jon Derrick)
- fix Intel VMD suspend/resume by releasing IRQs on suspend (Scott
Bauer)
- fix a Function-Level Reset issue with Intel 750 NVMe by waiting
longer (up to 60sec instead of 1sec) for device to become ready
(Sinan Kaya)
- fix a Function-Level Reset issue on iProc Stingray by working around
hardware defects in the CRS implementation (Oza Pawandeep)
- fix an issue with Intel NVMe P3700 after an iProc reset by adding a
delay during shutdown (Oza Pawandeep)
- fix a Microsoft Hyper-V lockdep issue by polling instead of blocking
in compose_msi_msg() (Stephen Hemminger)
- fix a wireless LAN driver timeout by clearing DesignWare MSI
interrupt status after it is handled, not before (Faiz Abbas)
- fix DesignWare ATU enable checking (Jisheng Zhang)
- reduce Layerscape dependencies on the bootloader by doing more
initialization in the driver (Hou Zhiqiang)
- improve Intel VMD performance allowing allocation of more IRQ vectors
than present CPUs (Keith Busch)
- improve endpoint framework support for initial DMA mask, different
BAR sizes, configurable page sizes, MSI, test driver, etc (Kishon
Vijay Abraham I, Stan Drozd)
- rework CRS support to add periodic messages while we poll during
enumeration and after Function-Level Reset and prepare for possible
other uses of CRS (Sinan Kaya)
- clean up Root Port AER handling by removing unnecessary code and
moving error handler methods to struct pcie_port_service_driver
(Christoph Hellwig)
- clean up error handling paths in various drivers (Bjorn Andersson,
Fabio Estevam, Gustavo A. R. Silva, Harunobu Kurokawa, Jeffy Chen,
Lorenzo Pieralisi, Sergei Shtylyov)
- clean up SR-IOV resource handling by disabling VF decoding before
updating the corresponding resource structs (Gavin Shan)
- clean up DesignWare-based drivers by unifying quirks to update Class
Code and Interrupt Pin and related handling of write-protected
registers (Hou Zhiqiang)
- clean up by adding empty generic pcibios_align_resource() and
pcibios_fixup_bus() and removing empty arch-specific implementations
(Palmer Dabbelt)
- request exclusive reset control for several drivers to allow cleanup
elsewhere (Philipp Zabel)
- constify various structures (Arvind Yadav, Bhumika Goyal)
- convert from full_name() to %pOF (Rob Herring)
- remove unused variables from iProc, HiSi, Altera, Keystone (Shawn
Lin)
* tag 'pci-v4.14-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (170 commits)
PCI: xgene: Clean up whitespace
PCI: xgene: Define XGENE_PCI_EXP_CAP and use generic PCI_EXP_RTCTL offset
PCI: xgene: Fix platform_get_irq() error handling
PCI: xilinx-nwl: Fix platform_get_irq() error handling
PCI: rockchip: Fix platform_get_irq() error handling
PCI: altera: Fix platform_get_irq() error handling
PCI: spear13xx: Fix platform_get_irq() error handling
PCI: artpec6: Fix platform_get_irq() error handling
PCI: armada8k: Fix platform_get_irq() error handling
PCI: dra7xx: Fix platform_get_irq() error handling
PCI: exynos: Fix platform_get_irq() error handling
PCI: iproc: Clean up whitespace
PCI: iproc: Rename PCI_EXP_CAP to IPROC_PCI_EXP_CAP
PCI: iproc: Add 500ms delay during device shutdown
PCI: Fix typos and whitespace errors
PCI: Remove unused "res" variable from pci_resource_io()
PCI: Correct kernel-doc of pci_vpd_srdt_size(), pci_vpd_srdt_tag()
PCI/AER: Reformat AER register definitions
iommu/vt-d: Prevent VMD child devices from being remapping targets
x86/PCI: Use is_vmd() rather than relying on the domain number
...
* pci/enumeration:
PCI: Warn periodically while waiting for non-CRS ("device ready") status
PCI: Wait up to 60 seconds for device to become ready after FLR
PCI: Factor out pci_bus_wait_crs()
PCI: Add pci_bus_crs_vendor_id() to detect CRS response data
PCI: Always check for non-CRS response before timeout
PCI: Avoid race while enabling upstream bridges
PCI: Mark Broadcom HT2100 Root Port Extended Tags as broken
VMD currently only exists for Intel x86 products, so move the VMD quirk to
arch/x86.
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Casey reported that the AMD ARM A1100 SoC has a bug in its PCIe
Root Port where Upstream Transaction Layer Packets with the Relaxed
Ordering Attribute clear are allowed to bypass earlier TLPs with
Relaxed Ordering set, it would cause Data Corruption, so we need
to disable Relaxed Ordering Attribute when Upstream TLPs to the
Root Port.
Reported-and-suggested-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the Intel spec section 3.9.1 said:
3.9.1 Optimizing PCIe Performance for Accesses Toward Coherent Memory
and Toward MMIO Regions (P2P)
In order to maximize performance for PCIe devices in the processors
listed in Table 3-6 below, the soft- ware should determine whether the
accesses are toward coherent memory (system memory) or toward MMIO
regions (P2P access to other devices). If the access is toward MMIO
region, then software can command HW to set the RO bit in the TLP
header, as this would allow hardware to achieve maximum throughput for
these types of accesses. For accesses toward coherent memory, software
can command HW to clear the RO bit in the TLP header (no RO), as this
would allow hardware to achieve maximum throughput for these types of
accesses.
Table 3-6. Intel Processor CPU RP Device IDs for Processors Optimizing
PCIe Performance
Processor CPU RP Device IDs
Intel Xeon processors based on 6F01H-6F0EH
Broadwell microarchitecture
Intel Xeon processors based on 2F01H-2F0EH
Haswell microarchitecture
It means some Intel processors has performance issue when use the Relaxed
Ordering Attribute, so disable Relaxed Ordering for these root port.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When bit4 is set in the PCIe Device Control register, it indicates
whether the device is permitted to use relaxed ordering.
On some platforms using relaxed ordering can have performance issues or
due to erratum can cause data-corruption. In such cases devices must avoid
using relaxed ordering.
The patch adds a new flag PCI_DEV_FLAGS_NO_RELAXED_ORDERING to indicate that
Relaxed Ordering (RO) attribute should not be used for Transaction Layer
Packets (TLP) targeted towards these affected root complexes.
This patch checks if there is any node in the hierarchy that indicates that
using relaxed ordering is not safe. In such cases the patch turns off the
relaxed ordering by clearing the capability for this device.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Ashok Raj <ashok.raj@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The APM X-Gene PCIe root port does not support ACS at this point. However,
the hardware provides isolation and source validation through the SMMU.
The stream ID generated by the PCIe ports contain both the bus/device/
function number as well as the port ID in its 3 most significant bits.
Turn on ACS but disable all the peer-to-peer features.
Signed-off-by: Feng Kan <fkan@apm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Tanmay Inamdar <tinamdar@apm.com>
We're about to amend ACPI bus scan with DMI checks whether we're running
on a Mac to support Apple device properties in AML. The DMI checks are
performed for every single device, adding overhead for everything x86
that isn't Apple, which is the majority. Rafael and Andy therefore
request to perform the DMI match only once and cache the result.
Outside of ACPI various other Apple DMI checks exist and it seems
reasonable to use the cached value there as well. Rafael, Andy and
Darren suggest performing the DMI check in arch code and making it
available with a header in include/linux/platform_data/x86/.
To this end, add early_platform_quirks() to arch/x86/kernel/quirks.c
to perform the DMI check and invoke it from setup_arch(). Switch over
all existing Apple DMI checks, thereby fixing two deficiencies:
* They are now #defined to false on non-x86 arches and can thus be
optimized away if they're located in cross-arch code.
* Some of them only match "Apple Inc." but not "Apple Computer, Inc.",
which is used by BIOSes released between January 2006 (when the first
x86 Macs started shipping) and January 2007 (when the company name
changed upon introduction of the iPhone).
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Suggested-by: Darren Hart <dvhart@infradead.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ATS is broken on this hardware and causes IOMMU stalls and system failure.
Disable ATS on these devices to make them usable again with IOMMU enabled.
Note that the commit in the Fixes tag is not buggy; it just uncovers the
problem in the hardware by increasing the ATS flush rate.
Link: https://lists.linuxfoundation.org/pipermail/iommu/2017-March/020836.html
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1409201
Fixes: b1516a1465 ("iommu/amd: Implement flush queue")
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Per PCIe r3.1, sec 2.2.6.2 and 7.8.4, a Requester may not use 8-bit Tags
unless its Extended Tag Field Enable is set, but all Receivers/Completers
must handle 8-bit Tags correctly regardless of their Extended Tag Field
Enable.
Some devices do not handle 8-bit Tags as Completers, so add a quirk for
them. If we find such a device, we disable Extended Tags for the entire
hierarchy to make peer-to-peer DMA possible.
The Broadcom HT2100 seems to have issues with handling 8-bit tags. Mark it
as broken.
The pci_walk_bus() in the quirk handles devices we've enumerated in the
past, and pci_configure_device() handles devices we enumerate in the
future.
Fixes: 60db3a4d8c ("PCI: Enable PCIe Extended Tags if supported")
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1467674
Reported-and-tested-by: Wim ten Have <wim.ten.have@oracle.com>
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
[bhelgaas: changelog, tweak messages, rename bit and quirk]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/virtualization:
PCI: Remove __pci_dev_reset() and pci_dev_reset()
PCI: Split ->reset_notify() method into ->reset_prepare() and ->reset_done()
PCI: Protect pci_error_handlers->reset_notify() usage with device_lock()
PCI: Protect pci_driver->sriov_configure() usage with device_lock()
PCI: Mark Intel XXV710 NIC INTx masking as broken
PCI: Restore PRI and PASID state after Function-Level Reset
PCI: Cache PRI and PASID bits in pci_dev
* pci/pm:
PCI/PM: Avoid using device_may_wakeup() for runtime PM
x86/PCI: Avoid AMD SB7xx EHCI USB wakeup defect
PCI/PM: Restore the status of PCI devices across hibernation
drm/radeon: make MacBook Pro d3_delay quirk more generic
drm/amdgpu: remove unnecessary save/restore of pdev->d3_delay
PCI/PM: Add needs_resume flag to avoid suspend complete optimization
PCI: imx6: Fix config read timeout handling
switchtec: Fix minor bug with partition ID register
switchtec: Use new cdev_device_add() helper function
PCI: endpoint: Make PCI_ENDPOINT depend on HAS_DMA
The PCI Power Management Spec, r1.2, sec 5.6.1, requires a 10 millisecond
delay when powering on a device, i.e., transitioning from state D3hot to
D0.
Apparently some devices require more time, and d1f9809ed1 ("drm/radeon:
add quirk for d3 delay during switcheroo poweron for apple macbooks") added
an additional delay for the Radeon device in a MacBook Pro. 4807c5a8a0
("drm/radeon: add a PX quirk list") made the affected device more explicit.
Add a generic PCI quirk to increase the d3_delay. This means we will use
the additional delay for *all* wakeups from D3, not just those initiated by
radeon_switcheroo_set_state().
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andreas Boll <andreas.boll.dev@gmail.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
CC: Maarten Lankhorst <maarten.lankhorst@canonical.com>
PCI_STD_RESOURCE_END is (confusingly) the index of the last valid BAR, not
the *number* of BARs. To iterate through all possible BARs, we need to
include PCI_STD_RESOURCE_END.
Fixes: 9fe373f999 ("PCI: Increase IBM ipr SAS Crocodile BARs to at least system page size")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Just like the other XL710 and X710 variants, the XXV710 device IDs appear
to have the same hardware bug, the status register doesn't report pending
interrupts resulting in "irq xx: nobody cared..." errors from the spurious
interrupt handler when we try to use it with device assignment.
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
* pci/virtualization:
ixgbe: Use pcie_flr() instead of duplicating it
IB/hfi1: Use pcie_flr() instead of duplicating it
PCI: Call pcie_flr() from reset_chelsio_generic_dev()
PCI: Call pcie_flr() from reset_intel_82599_sfp_virtfn()
PCI: Export pcie_flr()
PCI: Add sysfs sriov_drivers_autoprobe to control VF driver binding
PCI: Avoid FLR for Intel 82579 NICs
Conflicts:
include/linux/pci.h
* pci/irq:
PCI: Disable boot interrupt quirk for ASUS M2N-LR
nvme/pci: Switch to pci_request_irq()
PCI/irq: Add pci_request_irq() and pci_free_irq() helpers
genirq: Return the IRQ name from free_irq()
genirq: Fix indentation in remove_irq()
The ASUS M2N-LR should not trigger boot interrupt quirks although it
carries an Intel 6702PXH. On this board the boot interrupt quirks cause
incorrect IRQ assignments and should be disabled.
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=43074
Tested-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Instead of copy & pasting and old version of the code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The 82599 quirk contained an outdated copy of the FLR code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
On Cavium ThunderX2 arm64 SoCs (formerly known as Broadcom Vulcan), the PCI
topology is slightly unusual. For a multi-node system, it looks like:
00:00.0 PCI bridge to [bus 01-1e]
01:0a.0 PCI-to-PCIe bridge to [bus 02-04]
02:00.0 PCIe Root Port bridge to [bus 03-04] (XLATE_ROOT)
03:00.0 PCIe Endpoint
pci_for_each_dma_alias() assumes IOMMU translation is done at the root of
the PCI hierarchy. It generates 03:00.0, 01:0a.0, and 00:00.0 as DMA
aliases for 03:00.0 because buses 01 and 00 are non-PCIe buses that don't
carry the Requester ID.
Because the ThunderX2 IOMMU is at 02:00.0, the Requester IDs 01:0a.0 and
00:00.0 are never valid for the endpoint. This quirk stops alias
generation at the XLATE_ROOT bridge so we won't generate 01:0a.0 or
00:00.0.
The current IOMMU code only maps the last alias (this is a separate bug in
itself). Prior to this quirk, we only created IOMMU mappings for the
invalid Requester ID 00:00:0, which never matched any DMA transactions.
With this quirk, we create IOMMU mappings for a valid Requester ID, which
fixes devices with no aliases but leaves devices with aliases still broken.
The last alias for the endpoint is also used by the ARM GICv3 MSI-X code.
Without this quirk, the GIC Interrupt Translation Tables are setup with the
invalid Requester ID, and the MSI-X generated by the device fails to be
translated and routed.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=195447
Signed-off-by: Jayachandran C <jnair@caviumnetworks.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: David Daney <david.daney@cavium.com>
The ITE 8893 bridge has the same problems as the ITE 8892, which were
resulting in crippling an older PCI 1Gbps NIC down to 45Mbps throughput
with IOMMU and VT-d enabled. With the patch, this old e1000 goes back up
to ~900Mbps.
Suggested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Per Intel Specification Update 335553-002 (see link below), some 82579
network adapters advertise a Function Level Reset (FLR) capability, but
they can hang when an FLR is triggered.
To reproduce the problem, attach the device to a VM, then detach and try to
attach again.
Add a quirk to prevent the use of FLR on these devices.
[bhelgaas: changelog, comments]
Link: http://www.intel.com/content/dam/www/public/us/en/documents/specification-updates/82579lm-82579v-gigabit-network-connection-spec-update.pdf
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Only apply the Cavium ACS quirk to devices with ID in the range
0xa000-0xa0ff. These are the on-chip PCI devices for CN81xx/CN83xx/CN88xx.
Fixes: b404bcfbf0 ("PCI: Add ACS quirk for all Cavium devices")
Reported-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Manish Jaggi <mjaggi@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Fix typos and add the following to the scripts/spelling.txt:
followings||following
While we are here, add a missing colon in the boilerplate in DT binding
documents. The "you SoC" in allwinner,sunxi-pinctrl.txt was fixed as
well.
I reworded "as the followings:" to "as follows:" for
drivers/usb/gadget/udc/renesas_usb3.c.
Link: http://lkml.kernel.org/r/1481573103-11329-32-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* pci/host-hisi:
PCI: generic: Call pci_fixup_irqs() only on ARM
PCI: Disable MSI for HiSilicon Hip06/Hip07 Root Ports
PCI: hisi: Rename config space accessors to remove "acpi"
PCI: hisi: Add DT almost-ECAM support for Hip06/Hip07 host controllers
PCI: hisi: Use of_device_get_match_data() to simplify probe
Conflicts:
drivers/pci/dwc/pcie-hisi.c
The Qualcomm QDF2xxx root ports don't advertise an ACS capability, but they
do provide ACS-like features to disable peer transactions and validate bus
numbers in requests.
To be specific:
* Hardware supports source validation but it will report the issue as
Completer Abort instead of ACS Violation.
* Hardware doesn't support peer-to-peer and each root port is a root
complex with unique segment numbers.
* It is not possible for one root port to pass traffic to the other root
port. All PCIe transactions are terminated inside the root port.
Add an ACS quirk for the QDF2400 and QDF2432 products.
[bhelgaas: changelog]
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Sort the list of Intel devices that have no PCI D3 delay by ID. Add a
comment for group of devices that had not been marked yet.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCIe Root Port in Hip06/Hip07 SoCs advertises an MSI capability, but it
cannot generate MSIs. It can transfer MSI/MSI-X from downstream devices,
but does not support MSI/MSI-X itself.
Add a quirk to prevent use of MSI/MSI-X by the Root Port.
[bhelgaas: changelog, sort vendor ID #define, drop device ID #define]
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
The Broadcom Northstar2 SoC has a number of quirks for the PAXC
(internal/fake) PCI bus. Specifically, the PCI config space is shared
between the root port and the first PF (ie., PF0), and a number of fields
are tied to zero (thus preventing them from being set). These cannot be
"fixed" in device firmware, so we must fix them with a quirk.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Intel 200-series chipsets have the same errata as 100-series: the ACS
capability doesn't follow the PCIe spec, the capability and control
registers are dwords rather than words. Add PCIe root port device IDs to
existing quirk.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
* pci/virtualization:
PCI: Add comments about ROM BAR updating
PCI: Decouple IORESOURCE_ROM_ENABLE and PCI_ROM_ADDRESS_ENABLE
PCI: Remove pci_resource_bar() and pci_iov_resource_bar()
PCI: Don't update VF BARs while VF memory space is enabled
PCI: Separate VF BAR updates from standard BAR updates
PCI: Update BARs using property bits appropriate for type
PCI: Ignore BAR updates on virtual functions
PCI: Do any VF BAR updates before enabling the BARs
PCI: Support INTx masking on ConnectX-4 with firmware x.14.1100+
PCI: Convert Mellanox broken INTx quirks to be for listed devices only
PCI: Convert broken INTx masking quirks from HEADER to FINAL
net/mlx4_core: Use device ID defines
PCI: Add Mellanox device IDs
There is at least one Chelsio 10Gb card which uses VPD area to store some
non-standard blocks (example below). However pci_vpd_size() returns the
length of the first block only assuming that there can be only one VPD "End
Tag".
Since 4e1a635552 ("vfio/pci: Use kernel VPD access functions"), VFIO
blocks access beyond that offset, which prevents the guest "cxgb3" driver
from probing the device. The host system does not have this problem as its
driver accesses the config space directly without pci_read_vpd().
Add a quirk to override the VPD size to a bigger value. The maximum size
is taken from EEPROMSIZE in drivers/net/ethernet/chelsio/cxgb3/common.h.
We do not read the tag as the cxgb3 driver does as the driver supports
writing to EEPROM/VPD and when it writes, it only checks for 8192 bytes
boundary. The quirk is registered for all devices supported by the cxgb3
driver.
This adds a quirk to the PCI layer (not to the cxgb3 driver) as the cxgb3
driver itself accesses VPD directly and the problem only exists with the
vfio-pci driver (when cxgb3 is not running on the host and may not be even
loaded) which blocks accesses beyond the first block of VPD data. However
vfio-pci itself does not have quirks mechanism so we add it to PCI.
This is the controller:
Ethernet controller [0200]: Chelsio Communications Inc T310 10GbE Single Port Adapter [1425:0030]
This is what I parsed from its VPD:
===
b'\x82*\x0010 Gigabit Ethernet-SR PCI Express Adapter\x90J\x00EC\x07D76809 FN\x0746K'
0000 Large item 42 bytes; name 0x2 Identifier String
b'10 Gigabit Ethernet-SR PCI Express Adapter'
002d Large item 74 bytes; name 0x10
#00 [EC] len=7: b'D76809 '
#0a [FN] len=7: b'46K7897'
#14 [PN] len=7: b'46K7897'
#1e [MN] len=4: b'1037'
#25 [FC] len=4: b'5769'
#2c [SN] len=12: b'YL102035603V'
#3b [NA] len=12: b'00145E992ED1'
007a Small item 1 bytes; name 0xf End Tag
0c00 Large item 16 bytes; name 0x2 Identifier String
b'S310E-SR-X '
0c13 Large item 234 bytes; name 0x10
#00 [PN] len=16: b'TBD '
#13 [EC] len=16: b'110107730D2 '
#26 [SN] len=16: b'97YL102035603V '
#39 [NA] len=12: b'00145E992ED1'
#48 [V0] len=6: b'175000'
#51 [V1] len=6: b'266666'
#5a [V2] len=6: b'266666'
#63 [V3] len=6: b'2000 '
#6c [V4] len=2: b'1 '
#71 [V5] len=6: b'c2 '
#7a [V6] len=6: b'0 '
#83 [V7] len=2: b'1 '
#88 [V8] len=2: b'0 '
#8d [V9] len=2: b'0 '
#92 [VA] len=2: b'0 '
#97 [RV] len=80: b's\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00'...
0d00 Large item 252 bytes; name 0x11
#00 [VC] len=16: b'122310_1222 dp '
#13 [VD] len=16: b'610-0001-00 H1\x00\x00'
#26 [VE] len=16: b'122310_1353 fp '
#39 [VF] len=16: b'610-0001-00 H1\x00\x00'
#4c [RW] len=173: b'\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00'...
0dff Small item 0 bytes; name 0xf End Tag
10f3 Large item 13315 bytes; name 0x62
!!! unknown item name 98: b'\xd0\x03\x00@`\x0c\x08\x00\x00\x00\x00\x00\x00\x00\x00\x00'
===
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
It's not very enlightening to see
pci 0000:07:00.0: [Firmware Bug]: VPD access disabled
in the dmesg log because there's no clue about what the firmware bug is.
Expand the message to explain why we're disabling VPD.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Mellanox devices were marked as having INTx masking ability broken. As a
result, the VFIO driver fails to start when more than one device function
is passed-through to a VM if both have the same INTx pin.
Prior to Connect-IB, Mellanox devices exposed to the operating system one
PCI function per all ports. Starting from Connect-IB, the devices are
function-per-port. When passing the second function to a VM, VFIO will
fail to start.
Exclude ConnectX-4, ConnectX4-Lx and Connect-IB from the list of Mellanox
devices marked as having broken INTx masking:
- ConnectX-4 and ConnectX4-LX firmware version is checked. If INTx
masking is supported, we unmark the broken INTx masking.
- Connect-IB does not support INTx currently so will not cause any
problem.
[bhelgaas: call pci_disable_device() always, after iounmap()]
Fixes: 11e42532ad ("PCI: Assume all Mellanox devices have broken INTx masking")
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Change Mellanox's broken_intx_masking() quirk from an "all Mellanox
devices" to a quirk for listed devices only.
[bhelgaas: remove #defines, reorder to keep other quirks together]
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Convert all quirk_broken_intx_masking() quirks from HEADER to FINAL.
The quirk sets dev->broken_intx_masking, which is only used by
pci_intx_mask_supported(), which is not needed until after FINAL
quirks have been run.
[bhelgaas: changelog]
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Bjorn Helgaas