If fec MDIO write method succeeds its return value comes from
call to pm_runtime_get_sync().
But pm_runtime_get_sync() can also return 1.
In case of Micrel KSZ9031 PHY this value will then
be returned along the call chain of phy_write() ->
ksz9031_extended_write() -> ksz9031_center_flp_timing() ->
ksz9031_config_init() -> phy_init_hw() -> phy_attach_direct() ->
phy_connect_direct().
Then phy_connect() will cast it into a pointer using ERR_PTR(),
which then fec_enet_mii_probe() will try to dereference
resulting in an oops.
Fix it by normalizing return value of pm_runtime_get_sync()
to be zero if positive in MDIO write method.
Fixes: 8fff755e9f ("net: fec: Ensure clocks are enabled while using mdio bus")
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch just to re-submit the patch "db3421c114cfa6326" because the
patch "4d494cdc92b3b9a0" remove the change.
Clear any pending receive interrupt before we process a pending packet.
This helps to avoid any spurious interrupts being raised after we have
fully cleaned the receive ring, while still allowing an interrupt to be
raised if we receive another packet.
The position of this is critical: we must do this prior to reading the
next packet status to avoid potentially dropping an interrupt when a
packet is still pending.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than re-initialising the entire completion on every mdio access,
use reinit_completion() which only resets the completion count. This
avoids possible reinitialisation of the contained spinlock and waitqueue
while they may be in use (eg, mid-completion.)
Such an event could occur if there's a long delay in interrupt handling
causing the mdio accessor to time out, then a second access comes in
while the interrupt handler on a different CPU has called complete().
Another scenario where this has been observed is while locking has
been missing at the phy layer, allowing concurrent attempts to access
the MDIO bus.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/cavium/Kconfig
The cavium conflict was overlapping dependency
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to use the IS_ERR_VALUE() macro for checking
the return value from pm_runtime_* functions.
Just do a simple negative test instead.
The semantic patch that makes this change is available
in scripts/coccinelle/api/pm_runtime.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we transmit a fragmented skb, we may run into a race like the
following scenario (assume txq->cur_tx is next to txq->dirty_tx):
cpu 0 cpu 1
fec_enet_txq_submit_skb
reserve a bdp for the first fragment
fec_enet_txq_submit_frag_skb
update the bdp for the other fragment
update txq->cur_tx
fec_enet_tx_queue
bdp = fec_enet_get_nextdesc(txq->dirty_tx, fep, queue_id);
This bdp is the bdp reserved for the first segment. Given
that this bdp BD_ENET_TX_READY bit is not set and txq->cur_tx
is already pointed to a bdp beyond this one. We think this is a
completed bdp and try to reclaim it.
update the bdp for the first segment
update txq->cur_tx
So we shouldn't update the txq->cur_tx until all the update to the
bdps used for fragments are performed. Also add the corresponding
memory barrier to guarantee that the update to the bdps, dirty_tx and
cur_tx performed in the proper order.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The clocks are initially active and thus the device is marked active.
This still keeps the PM refcount at 0, the pm_runtime_put_autosuspend()
call at the end of probe then leaves us with an invalid refcount of -1,
which in turn leads to the device staying in suspended state even though
netdev open had been called.
Fix this by initializing the refcount to be coherent with the initial
device status.
Fixes:
8fff755e9f (net: fec: Ensure clocks are enabled while using mdio bus)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a switch is attached to the mdio bus, the mdio bus can be used
while the interface is not open. If the IPG clock is not enabled, MDIO
reads/writes will simply time out.
Add support for runtime PM to control this clock. Enable/disable this
clock using runtime PM, with open()/close() and mdio read()/write()
function triggering runtime PM operations. Since PM is optional, the
IPG clock is enabled at probe and is no longer modified by
fec_enet_clk_enable(), thus if PM is not enabled in the kernel, it is
guaranteed the clock is running when MDIO operations are performed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Cc: tyler.baker@linaro.org
Cc: fabio.estevam@freescale.com
Cc: shawn.guo@linaro.org
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function frees resources and cancels delayed work item that
have been initialized in fec_ptp_init().
Use this to do proper error handling if something goes wrong in
probe function after fec_ptp_init has been called.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So it gets freed when the device is going away.
This fixes a DMA memory leak on driver probe() fail and driver
remove().
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 6c3e921b18.
commit 6c3e921b18 ("net: fec: Ensure clocks are enabled while using mdio
bus") prevents the kernel to boot on mx6 boards, so let's revert it.
Reported-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a switch is attached to the mdio bus, the mdio bus can be used
while the interface is not open. If the IPG clock is not enabled, MDIO
reads/writes will simply time out.
Add support for runtime PM to control this clock. Enable/disable this
clock using runtime PM, with open()/close() and mdio read()/write()
function triggering runtime PM operations. Since PM is optional, the
IPG clock is enabled at probe and is no longer modified by
fec_enet_clk_enable(), thus if PM is not enabled in the kernel, it is
guaranteed the clock is running when MDIO operations are performed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all silicon implementations of the Freescale FEC hardware module
have the RACC (Receive Accelerator Function) register, so we should not
be trying to access it on those that don't. Currently none of the ColdFire
based parts with a FEC have it.
Support for RACC was introduced by commit 4c09eed9 ("net: fec: Enable imx6
enet checksum acceleration"). A fix was introduced in commit d1391930
("net: fec: Fix build for MCF5272") that disables its use on the ColdFire
M5272 part, but it doesn't fix the general case of other ColdFire parts.
To fix we create a quirk flag, FEC_QUIRK_HAS_RACC, and check it before
working with the RACC register.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Below case causes mii bus probe failed:
ifconfig eth0 down -> suspend/resume with Mega/fax mix off -> ifconfig eth0 up
In i.MX6SX/i.MX7D chip, Mega/fast mix off feature is supported that means most of
SOC power will be off including ENET MAC for power saving. Once ENET MAC power
off, all initialized MAC registers reset to default, so in the case, it must
init MAC prior to mii bus probe.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables the ethtool's "-d" and "--register-dump"
options for fec devices.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RGMII-ID uses an internal delay within the transmitter or receiver. This
feature is phy specific. The rest of the communication is normal RGMII.
So the fec driver has to check for all RGMII modes, not only
'PHY_INTERFACE_MODE_RGMII'.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FEC modules used on i.MX28 and newer have a register to tune the MDIO
output hold time that should be at least 10 ns. Up to now this value was not
explicitly set and so resulted in less hold time if the fec clock was
faster than 100 MHz.
This was noticed on an i.MX28 machine that uses an input clock of ~150
Mhz which resulted in unreliable communication with a Marvell switch.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 2b995f6398.
Панов Андрей reported the following regression:
"Commit 2b995f6398 in 4.0.0-rc3 introduces a
nasty bug in transmit, corrupting packets.
To reproduce:
$ dd if=/dev/zero of=zeros bs=1M count=20
$ md5sum -b zeros
8f4e33f3dc3e414ff94e5fb6905cba8c *zeros
This checksum is correct.
Copy file "zeros" to another host with NFS, and it gets corrupted, checksum is
changed.
File should be big, small amounts of transmit isn't affected.
I use an i.MX6 Quad board.
If this commit is reverted, all works fine."
Reported-by: Панов Андрей <rockford@yandex.ru>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current driver support receive VLAN CTAG HW acceleration feature
(NETIF_F_HW_VLAN_CTAG_RX) through software simulation. There calls the
api .skb_copy_to_linear_data_offset() to skip the VLAN tag, but there
have overlap between the two memory data point range. The patch just fix
the issue.
V2:
Michael Grzeschik suggest to use memmove() instead of skb_copy_to_linear_data_offset().
Reported-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Fixes: 1b7bde6d65 ("net: fec: implement rx_copybreak to improve rx performance")
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the driver is removed (e.g. using unbind through sysfs), the
clocks get disabled twice, once on fec_enet_close and once on
fec_drv_remove. Since the clocks are enabled only once, this leads
to a warning:
WARNING: CPU: 0 PID: 402 at drivers/clk/clk.c:992 clk_core_disable+0x64/0x68()
Remove the call to fec_enet_clk_enable in fec_drv_remove to balance
the clock enable/disable calls again. This has been introduce by
e8fcfcd568 ("net: fec: optimize the clock management to save power").
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kfree() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable kernel config "CONFIG_HAVE_DMA_API_DEBUG", FEC have kernel warning:
[ 6.650444] fec 2188000.ethernet: DMA-API: device driver tries to free DMA memory it has not allocated
[ 6.664289] Modules linked in:
[ 6.667378] CPU: 0 PID: 3 Comm: ksoftirqd/0 Not tainted 3.19.0-rc4-00688-g8834016-dirty #150
[ 6.675841] Hardware name: Freescale i.MX6 SoloX (Device Tree)
[ 6.681698] Backtrace:
[ 6.684189] [<80011e3c>] (dump_backtrace) from [<80011fdc>] (show_stack+0x18/0x1c)
[ 6.691789] r6:80890154 r5:00000000 r4:00000000 r3:00000000
[ 6.697533] [<80011fc4>] (show_stack) from [<806d2d88>] (dump_stack+0x80/0x9c)
[ 6.704799] [<806d2d08>] (dump_stack) from [<8002a4e4>] (warn_slowpath_common+0x7c/0xb4)
[ 6.712917] r5:00000445 r4:00000000
[ 6.716544] [<8002a468>] (warn_slowpath_common) from [<8002a5c0>] (warn_slowpath_fmt+0x38/0x40)
[ 6.725265] r8:809a2ee8 r7:00000000 r6:00000000 r5:00000000 r4:00000042
[ 6.732087] [<8002a58c>] (warn_slowpath_fmt) from [<802d6268>] (check_unmap+0x86c/0x98c)
[ 6.740202] r3:808c79bc r2:8089060c
[ 6.743826] [<802d59fc>] (check_unmap) from [<802d65e4>] (debug_dma_unmap_page+0x80/0x88)
[ 6.752029] r10:00000000 r9:00000000 r8:00000000 r7:00000001 r6:be12a410 r5:00000000
[ 6.759967] r4:00000042
[ 6.762538] [<802d6564>] (debug_dma_unmap_page) from [<80440248>] (fec_enet_rx_napi+0x7ec/0xb9c)
[ 6.771345] r7:00000400 r6:be3e4000 r5:bf08fa20 r4:be036000
[ 6.777094] [<8043fa5c>] (fec_enet_rx_napi) from [<8056ae24>] (net_rx_action+0x134/0x324)
[ 6.785297] r10:be089e60 r9:80998180 r8:ffff8d68 r7:0000012c r6:00000040 r5:00000001
[ 6.793239] r4:be036718
[ 6.795801] [<8056acf0>] (net_rx_action) from [<8002db24>] (__do_softirq+0x138/0x2d0)
[ 6.803655] r10:00000003 r9:00000003 r8:80996378 r7:8099c080 r6:00000100 r5:8099c08c
[ 6.811593] r4:00000000
[ 6.814157] [<8002d9ec>] (__do_softirq) from [<8002dd00>] (run_ksoftirqd+0x44/0x5c)
[ 6.821836] r10:00000000 r9:00000000 r8:809b133c r7:00000000 r6:00000001 r5:00000000
[ 6.829775] r4:be027e80
[ 6.832346] [<8002dcbc>] (run_ksoftirqd) from [<80048290>] (smpboot_thread_fn+0x154/0x1c4)
[ 6.840649] [<8004813c>] (smpboot_thread_fn) from [<80044780>] (kthread+0xdc/0xf8)
[ 6.848224] r10:00000000 r8:00000000 r7:8004813c r6:be027e80 r5:be027ec0 r4:00000000
[ 6.856179] [<800446a4>] (kthread) from [<8000ebc8>] (ret_from_fork+0x14/0x2c)
[ 6.863425] r7:00000000 r6:00000000 r5:800446a4 r4:be027ec0
[ 6.869156] ---[ end trace 861cf914d2461a8b ]---
There have one bug in .fec_enet_tx_queue() function to unmap the DMA memory:
For SG or TSO, get one buffer descriptor and then unmap the related DMA memory, and then
get the next buffer descriptor, loop to while() to check "TX_READY". If "TX_READY" bit
still __IS__ existed in the BD (The next fraglist or next TSO packet is not transmited
complitely), exit the current clean work. When the next work is triggered, it still repeat
above step with the same BD. The potential issue is that unmap the same DMA memory for
multiple times.
The patch fix the clean work for SG and TSO packet.
Reported-by: Anand Moon <moon.linux@yahoo.com>
Reported-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/xen-netfront.c
Minor overlapping changes in xen-netfront.c, mostly to do
with some buffer management changes alongside the split
of stats into TX and RX.
Signed-off-by: David S. Miller <davem@davemloft.net>
On i.MX28, the MDIO bus is shared between the two FEC instances.
The driver makes sure that the second FEC uses the MDIO bus of the
first FEC. This is done conditionally if FEC_QUIRK_ENET_MAC is set.
However, in newer designs, such as Vybrid or i.MX6SX, each FEC MAC
has its own MDIO bus. Simply removing the quirk FEC_QUIRK_ENET_MAC
is not an option since other logic, triggered by this quirk, is
still needed.
Furthermore, there are board designs which use the same MDIO bus
for both PHY's even though the second bus would be available on the
SoC side. Such layout are popular since it saves pins on SoC side.
Due to the above quirk, those boards currently do work fine. The
boards in the mainline tree with such a layout are:
- Freescale Vybrid Tower with TWR-SER2 (vf610-twr.dts)
- Freescale i.MX6 SoloX SDB Board (imx6sx-sdb.dts)
This patch adds a new quirk FEC_QUIRK_SINGLE_MDIO for i.MX28, which
makes sure that the MDIO bus of the first FEC is used in any case.
However, the boards above do have a SoC with a MDIO bus for each FEC
instance. But the PHY's are not connected in a 1:1 configuration. A
proper device tree description is needed to allow the driver to
figure out where to find its PHY. This patch fixes that shortcoming
by adding a MDIO bus child node to the first FEC instance, along
with the two PHY's on that bus, and making use of the phy-handle
property to add a reference to the PHY's.
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch initialises the fep->netdev pointer. This pointer was not
initialised at all, but is used in fec_enet_timeout_work and in some
error paths.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for Wake-on-LAN using Magic Packet. ENET IP supports sleep mode
in low power status, when system enter suspend status, Magic packet can
wake up system even if all SOC clocks are gate. The patch doing below things:
- flagging the device as a wakeup source for the system, as well as
its Wake-on-LAN interrupt
- prepare the hardware for entering WoL mode
- add standard ethtool WOL interface
- enable the ENET interrupt to wake us
Tested on i.MX6q/dl sabresd, sabreauto boards, i.MX6SX arm2 boards.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do camera capture test on i.MX6q sabresd board, and save the capture data to
nfs rootfs. The command is:
gst-launch-1.0 -e imxv4l2src device=/dev/video1 num-buffers=2592000 ! tee name=t !
queue ! imxv4l2sink sync=false t. ! queue ! vpuenc ! queue ! mux. pulsesrc num-buffers=3720937
blocksize=4096 ! 'audio/x-raw, rate=44100, channels=2' ! queue ! imxmp3enc ! mpegaudioparse !
queue ! mux. qtmux name=mux ! filesink location=video_recording_long.mov
After about 10 hours running, there have net watchdog timeout kernel dump:
...
WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:264 dev_watchdog+0x2b4/0x2d8()
NETDEV WATCHDOG: eth0 (fec): transmit queue 0 timed out
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.14.24-01051-gdb840b7 #440
[<80014e6c>] (unwind_backtrace) from [<800118ac>] (show_stack+0x10/0x14)
[<800118ac>] (show_stack) from [<806ae3f0>] (dump_stack+0x78/0xc0)
[<806ae3f0>] (dump_stack) from [<8002b504>] (warn_slowpath_common+0x68/0x8c)
[<8002b504>] (warn_slowpath_common) from [<8002b558>] (warn_slowpath_fmt+0x30/0x40)
[<8002b558>] (warn_slowpath_fmt) from [<8055e0d4>] (dev_watchdog+0x2b4/0x2d8)
[<8055e0d4>] (dev_watchdog) from [<800352d8>] (call_timer_fn.isra.33+0x24/0x8c)
[<800352d8>] (call_timer_fn.isra.33) from [<800354c4>] (run_timer_softirq+0x184/0x220)
[<800354c4>] (run_timer_softirq) from [<8002f420>] (__do_softirq+0xc0/0x22c)
[<8002f420>] (__do_softirq) from [<8002f804>] (irq_exit+0xa8/0xf4)
[<8002f804>] (irq_exit) from [<8000ee5c>] (handle_IRQ+0x54/0xb4)
[<8000ee5c>] (handle_IRQ) from [<80008598>] (gic_handle_irq+0x28/0x5c)
[<80008598>] (gic_handle_irq) from [<800123c0>] (__irq_svc+0x40/0x74)
Exception stack(0x80d27f18 to 0x80d27f60)
7f00: 80d27f60 0000014c
7f20: 8858c60e 0000004d 884e4540 0000004d ab7250d0 80d34348 00000000 00000000
7f40: 00000001 00000000 00000017 80d27f60 800702a4 80476e6c 600f0013 ffffffff
[<800123c0>] (__irq_svc) from [<80476e6c>] (cpuidle_enter_state+0x50/0xe0)
[<80476e6c>] (cpuidle_enter_state) from [<80476fa8>] (cpuidle_idle_call+0xac/0x154)
[<80476fa8>] (cpuidle_idle_call) from [<8000f174>] (arch_cpu_idle+0x8/0x44)
[<8000f174>] (arch_cpu_idle) from [<80064c54>] (cpu_startup_entry+0x100/0x158)
[<80064c54>] (cpu_startup_entry) from [<80cd8a9c>] (start_kernel+0x304/0x368)
---[ end trace 09ebd32fb032f86d ]---
...
There might have a race in napi_schedule(), leaving interrupts disabled forever.
After these patch, the case still work more than 40 hours running.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Before phy device link up, we only enable FEC mdio interrupt, which
is more reasonable.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For i.MX6SX FEC controller, there have interrupt mask and event
field extension. To support all SOCs FEC, we clear all interrupt
events during MAVC initial process.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some i.MX6 serial boards, phy power and refrence clock are supplied
or controlled by SOC. When do suspend/resume test, the power and clock
are disabled, so phy device link down.
For current driver, fep->link is still up status, which cause extra operation
like below code. To avoid the dumy operation, we set fep->link to down when
phy device is real down.
...
if (fep->link) {
napi_disable(&fep->napi);
netif_tx_lock_bh(ndev);
fec_stop(ndev);
netif_tx_unlock_bh(ndev);
napi_enable(&fep->napi);
fep->link = phy_dev->link;
status_change = 1;
}
...
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i.MX6SX fec support three rx ring1, the current driver lost to init
ring1 and ring2 maximum receive buffer size, that cause receving
frame date length error. The driver reports "rcv is not +last" error
log in user case.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The return value of swap_buffer() is not used by any caller, thus
remove it.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate the DIV_ROUND_UP() and change the loop counter increment to
4 instead. This results in saving 6 instructions in the functions
assembly code.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
when swap_buffer() is being called, we know for sure, that we need to
byte swap the data. Furthermore, this function is called for swapping
data in both directions. Thus cpu_to_be32() is semantically not
correct for all use cases. Use swab32s() to reflect this.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
fep->bufdesc_ex is treated as a boolean value, thus declare it as
such.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 1b7bde6d65 ("net: fec: implement rx_copybreak to improve rx performance")
introduced a regression for i.MX28. The swap_buffer() function doing
the endian conversion of the received data on i.MX28 may access memory
beyond the actual packet size in the DMA buffer. fec_enet_copybreak()
does not copy those bytes, so that the last bytes of a packet may be
filled with invalid data after swapping.
This will likely lead to checksum errors on received packets.
E.g. when trying to mount an NFS rootfs:
UDP: bad checksum. From 192.168.1.225:111 to 192.168.100.73:44662 ulen 36
Do the byte swapping and copying to the new skb in one go if
necessary.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 278d240478 (net: fec: ptp: Enable PPS output based on ptp clock)
fec_enet_interrupt calls fec_ptp_check_pps_event unconditionally, which calls
into ptp_clock_event. If fep->ptp_clock is NULL, ptp_clock_event tries to
dereference the NULL pointer.
Since on i.MX53 fep->bufdesc_ex is not set, fec_ptp_init is never called,
and fep->ptp_clock is NULL, which reliably causes a kernel panic.
This patch adds a check for fep->ptp_clock == NULL in fec_enet_interrupt.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
iMX6SX IEEE 1588 module has one hw issue in capturing the ATVR register.
The current SW flow is:
ENET0->ATCR |= ENET_ATCR_CAPTURE_MASK;
ts_counter_ns = ENET0->ATVR;
The ATVR value is not expected value that cause LinuxPTP stack cannot be convergent.
ENET Block Guide/ Chapter for the iMX6SX (PELE) address the issue:
After set ENET_ATCR[Capture], there need some time cycles before the counter
value is capture in the register clock domain. The wait-time-cycles is at least
6 clock cycles of the slower clock between the register clock and the 1588 clock.
So need something like:
ENET0->ATCR |= ENET_ATCR_CAPTURE_MASK;
wait();
ts_counter_ns = ENET0->ATVR;
For iMX6SX, the 1588 ts_clk is fixed to 25Mhz, register clock is 66Mhz, so the
wait-time-cycles must be greater than 240ns (40ns * 6). The patch add 1us delay
before cpu read ATVR register.
Changes V2:
Modify the commit/comments log to describe the issue clearly.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FEC ptp timer has 4 channel compare/trigger function. It can be used to
enable pps output.
The pulse would be ouput high exactly on N second. The pulse ouput high
on compare event mode is used to produce pulse per second. The pulse
width would be one cycle based on ptp timer clock source.Since 31-bit
ptp hardware timer is used, the timer will wrap more than 2 seconds. We
need to reload the compare compare event about every 1 second.
Signed-off-by: Luwei Zhou <b45643@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
reproduce:
make ARCH=arm C=1 2>fec.txt drivers/net/ethernet/freescale/fec_main.o
cat fec.txt
sparse warnings:
drivers/net/ethernet/freescale/fec_main.c:2916:12: warning: context imbalance
in 'fec_set_features' - different lock contexts for basic block
Christopher Li suggest to change as below:
if (need_lock) {
lock();
do_something_real();
unlock();
} else {
do_something_real();
}
Reported-by: Fabio Estevam <festevam@gmail.com>
Suggested-by: Christopher Li <sparse@chrisli.org>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When fec_enet_alloc_buffers() fails we should better undo the previous actions,
which consists of: disabling the FEC clocks and putting the FEC pins into
inactive state.
The error path for fec_enet_mii_probe() is kept unchanged.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
reproduce:
wget https://git.kernel.org/cgit/linux/kernel/git/wfg/lkp-tests.git/plain/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
git checkout 1b7bde6d65
make.cross ARCH=m68k m5275evb_defconfig
make.cross ARCH=m68k
All error/warnings:
drivers/net/ethernet/freescale/fec_main.c: In function 'fec_enet_rx_queue':
>> drivers/net/ethernet/freescale/fec_main.c:1470:3: error: implicit declaration of function 'prefetch' [-Werror=implicit-function-declaration]
prefetch(skb->data - NET_IP_ALIGN);
^
cc1: some warnings being treated as errors
missed included prefetch.h
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Copy short frames and keep the buffers mapped, re-allocate skb instead of
memory copy for long frames.
- Add support for setting/getting rx_copybreak using generic ethtool tunable
Changes V3:
* As Eric Dumazet's suggestion that removing the copybreak module parameter
and only keep the ethtool API support for rx_copybreak.
Changes V2:
* Implements rx_copybreak
* Rx_copybreak provides module parameter to change this value
* Add tunable_ops support for rx_copybreak
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Free memory and disable all related clocks when there has no phy
connection or phy probe failed.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Align allocated rx data buffer size for dma map/unmap, otherwise
kernel print warning when enable DMA_API_DEBUG.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the ERR006358 workaround for imx6sx enet since the hw issue
was fixed on the SOC.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current driver loss Ftype field init for BD, which cause tx
queue #1 and #2 cannot work well.
Add Ftype field to BD to distiguish three queues for AVB:
0 -> Best Effort
1 -> ClassA
2 -> ClassB
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparse complains about fec_enet_select_queue() not being static.
Feedback from David Miller [1] was to remove this function instead of making it
static:
"Please just delete this function.
It's overriding code which does exactly the same thing.
Actually, more precisely, this code is duplicating code in a way that
bypasses many core facilitites of the networking. For example, this
override means that socket based flow steering, XPS, etc. are all
not happening on these devices.
Without ->ndo_select_queue(), the flow dissector does __netdev_pick_tx
which is exactly what you want to happen."
[1] http://www.spinics.net/lists/netdev/msg297653.html
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There have extra identation before .skb_copy_to_linear_data_offset(),
this patch just remove the identation.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enable three queues on imx6sx enet, and then do tx performance
test with iperf tool, after some time running, tx hang.
Found that:
If uDMA is running, software set TDAR may cause tx hang.
If uDMA is in idle, software set TDAR don't cause tx hang.
There is a TDAR race condition for mutliQ when the software sets TDAR
and the UDMA clears TDAR simultaneously or in a small window (2-4 cycles).
This will cause the udma_tx and udma_tx_arbiter state machines to hang.
The issue exist at i.MX6SX enet IP.
So, the Workaround is checking TDAR status four time, if TDAR cleared by
hardware and then write TDAR, otherwise don't set TDAR.
The patch is only one Workaround for the issue ERR007885.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i.MX6 SX support interrupt coalescence feature
By default, init the interrupt coalescing frame count threshold and
timer threshold.
Supply the ethtool interfaces as below for user tuning to improve
enet performance:
rx_max_coalesced_frames
rx_coalesce_usecs
tx_max_coalesced_frames
tx_coalesce_usecs
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
check tx and rx queue seperately.
fix typo, "Invalidate" and "fail".
change pr_err to pr_warn.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replacing strncpy with strlcpy to avoid strings that lacks null terminate.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use container_of instead of casting first structure member.
ARM cross-compiled but untested.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
i.MX6 SX change FEC alignment requirement.
i.MX6 SX change internal bus from AHB to AXI.
It require RX buffer must be 64 bytes alignment.
And remove TX buffer alignment requirement.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add compatible string "fsl,imx6sx-fec" for i.MX6SX.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i.MX6SX Enet-AVB support 3 tx queues, 3 rx queues.
For tx queues: ring 0 -> best effort
ring 1 -> Class A
ring 2 -> Class B
For rx queues:
ring 0 -> best effort
ring 1 -> receive VLAN packet with classification match
ring 2 -> receive VLAN packet with classification match
Add enet-avb IP multiqueue support for the driver.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For i.MX6SX enet use AXI bus, reset MAC will make system bus dead
if ENET-AXI bus has pending access (AHB bus should not have such issue).
So, disable enet with AVB MAC instead of reset MAC itself.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
initilized all queues according to queue number get from DT file.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Duan Fugang <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, the tx/rx queue number is 1, user can config the queue number
at DTS file like this:
fsl,num-tx-queues=<3>;
fsl,num-rx-queues=<3>
Since i.MX6SX enet-AVB IP support multi queues, so use multi queues
interface to allocate and set up an Ethernet device.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch just change data structure to support multi-queue.
Only 1 queue enabled.
Ethernet multiqueue mechanism can improve performance in SMP system.
For single hw queue, multiqueue can balance cpu loading.
For multi hw queues, multiple cores can process network packets in parallel,
and refer the article for the detail advantage for multiqueue:
http://vger.kernel.org/~davem/davem_nyc09.pdf
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <frank.li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add enet AVB feature macro define for imx6sx.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i.MX6sx enet has below clocks for user config:
clk_ipg: ipg_clk_s, ipg_clk_mac0_s, 66Mhz
clk_ahb: enet system clock, it is enet AXI clock for imx6sx.
For imx6sx, it alos is the clock source of interrupt coalescing.
The clock range: 200Mhz ~ 266Mhz.
clk_ref: refrence clock for tx and rx. For imx6sx enet RGMII mode,
the refrence clock is 125Mhz coming from internal PLL or external.
In i.MX6sx-arm2 board, the clock is from internal PLL.
clk_ref is optional, depends on board.
clk_enet_out: The clock can be output from internal PLL. It can supply 50Mhz
clock for phy. clk_enet_out is optional, depends on chip and board.
clk_ptp: 1588 ts clock. It is optional, depends on chip.
The patch add clk_ref to distiguish the different clocks.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current kernel hang on i.MX6SX with rootfs mount from MMC.
The root cause is that ptp uses a periodic timer to access enet register
even if ipg clock is disabled.
FEC ptp driver start one period timer to read 1588 counter register in the
ptp init function that is called after FEC driver is probed.
To save power, after FEC probe finish, FEC driver disable all clocks including
ipg clock that is needed for register access.
i.MX5x, i.MX6q/dl/sl FEC register access don't cause system hang when ipg clock
is disabled, just return zero value. But for i.MX6sx SOC, it cause system hang.
To avoid the issue, we need to check ptp clock status before ptp timer count access.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for specifying the phy to be used with the fec in the
devicetree using the standard phy-handle property and also supports
fixed-link.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of the CONFIG_PM_SLEEP ifdef by annotating the suspend/resume functions
with '__maybe_unused' in order to keep the code simpler and shorter.
While at it, declare the suspend/resume functions in a single line.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both transmit and receive use the same infrastructure for calculating
the packet timestamp. Rather than duplicating the code, provide a
function to do this common work. Model this function in the Intel
e1000e version which avoids calling ns_to_ktime() within the spinlock;
the spinlock is critical for timecounter_cyc2time() but not
ns_to_ktime().
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a useless status check in the transmit reap path - we have
already checked that the BD_ENET_TX_READY bit is clear, and as the
hardware only ever clears this bit, there is no way this test can ever
be true.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we timeout on transmit, it would be useful to dump the transmit
ring, so we can see the ring state. This can be helpful to diagnose
the cause of transmit timeouts.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows us to merge two separate preprocessor conditionals together.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear any pending receive interrupt before we process a pending packet.
This helps to avoid any spurious interrupts being raised after we have
fully cleaned the receive ring, while still allowing an interrupt to be
raised if we receive another packet.
The position of this is critical: we must do this prior to reading the
next packet status to avoid potentially dropping an interrupt when a
packet is still pending.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of "better implementation of iMX6 ERR006358 quirk", we no longer have
a requirement for a delayed work. Moreover, the work is now only used
for timeout purposes, so the timeout flag is also pointless - we set it
each time we queue the work, and the work clears it.
Replace the fec_enet_delayed_work struct with a standard work_struct,
resulting in simplified timeout handling code.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using a (delayed) workqueue for ERR006358 is not correct - a work queue
is a single-trigger device. Once the work queue has been scheduled, it
can't be re-scheduled until it has been run. This can cause problems -
with an appropriate packet timing, we can end up with packets queued,
but not sent by the hardware, resulting in the transmit timeout firing.
Re-implement this as per the workaround detailed in the ERR006358
documentation - if there are packets waiting to be sent when we service
the transmit ring, and we see that the transmitter is not running,
kick the transmitter to run the pending entries in the ring.
Testing here with a 10Mbit half duplex link sees the resulting iperf
TCP bandwidth increase from between 1 to 2Mbps to between 8 to 9Mbps.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many places call fec_restart() with the second parameter being some kind
of previously saved duplex value, but only two places call it with some
other setting. This is at odds with how the other link settings are
handled, and used to be racy before the rtnl locks were added to
fec_restart()'s various call paths.
Clean this up so all link capabilities are handled in the same way -
saved into the fec_enet_private structure, and then fec_restart() acts
on those settings.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the link goes down, the adjust_link method will be called, but
there is no synchronisation to ensure that we won't be processing some
last remaining packets via the NAPI handlers while performing a reset of
the device.
Add the necessary synchronisation to ensure that packet processing
is complete before we stop and reset the FEC.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing the features (receive checksumming) requires the hardware to be
reprogrammed, and also changes the checks in the receive packet
processing.
The current implementation has a race - fec_set_features() changes the
flags which alter the receive packet processing while the adapter is
active, and potentially receiving frames. Only after we've modified
the software flag do we shutdown and reconfigure the hardware.
This can lead to packets being received and marked with a valid checksum
(via CHECKSUM_UNNECESSARY) when the hardware checksum validation has not
yet been enabled.
We must quiesce the device, then change the software configuration for
this feature, and then resume the device if it was previously running.
The resulting code structure also allows us to add other configuration
features in this path without having to quiesce and resume the network
interface and device.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
fec_set_features() calls fec_stop() to stop the transmit ring while the
transmit queue is still active. This can lead to the transmit ring
being restarted by an intervening packet queued for transmission, or
by the tx quirk timer expiring.
Fix this by disabling NAPI (which ensures that the NAPI handlers are
not running), and then take the transmit lock while we stop and
restart the adapter (which prevents new packets being queued).
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
fec_suspend() calls fec_stop() to stop the transmit ring while the
transmit packet processing is still active. This can lead to the
transmit queue being restarted by an intervening packet queued for
transmission, or by the tx quirk timer expiring.
Fix this by disabling NAPI first, which will ensure that the NAPI
handlers are not running. Then, take the transmit lock before
detaching the netif device. This ensures that there are no races
with the transmit path - and also ensures that the watchdog won't
fire.
We can then safely stop the ethernet device itself, knowing that the
rest of the driver is safely shut down.
On resume, we bring the device back up in reverse order - we restart
the device, reattach the device (under the tx lock), and then enable
the NAPI handlers.
We also need to adjust the close function to cope with this new
sequence, so that it's possible to cleanly close down the driver
after the hardware fails to resume (eg, due to the regulator_enable()
or pinctrl calls in the resume path returning an error.)
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the second stage to "move calls to quiesce/resume packet
processing out of fec_restart()", where we remove calls which are not
appropriate to the call site.
In the majority of cases, there is no need to detach and reattach the
interface as we are holding the queue xmit lock across the reset. The
exception to that is in fec_resume(), where we are already detached by
the suspend function. Here, we can remove the call to detach the
interface.
We also do not need to stop the transmit queue. Holding the xmit lock
is enough to ensure that the transmit packet processing is not running
while we perform our task. However, since fec_restart() always cleans
the rings, we call netif_wake_queue() (or netif_device_attach() in the
case of resume) just before dropping the xmit lock. This prevents the
watchdog firing.
Lastly, always call napi_enable() after the device has been reattached
in the resume path so that we know that the transmit packet processing
is already in an enabled state, so we don't call netif_wake_queue()
while detached.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the calls to quiesce and resume packet processing out of
fec_restart() to its call sites. This is the first step in a two stage
clean up of this code, where we just move the calls out of fec_restart()
without changing them. Not everywhere needs to issue these calls, and
not everywhere needs all of these calls to be issued.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid calling fec_restart() or fec_stop() while the device is down
or not present (iow suspended.)
Although the ndo_timeout method will only be called if the device is
present and running, we defer this to a work queue. The work queue
can run independently, and so needs to repeat these checks to ensure
that a restart doesn't occur after the device has been taken down or
detached for suspend. In this case, we call fec_restart() in the
resume path, so nothing is lost.
For fec_set_features, we add a call to fec_restart() in fec_enet_open()
to ensure that the hardware is appropriate programmed when the interface
is opened. fec_set_features() call should not occur while we're
suspended, so we don't have to worry about that case.
The adjust_link needs similar treatment - this also is called from a
work queue, which may be run independently after we have taken the
device down and detached it. In this case, we just mark the link
down and take no further action. We will reset things appropriately
once the device is up and running again, at which point we will receive
another adjust_link callback.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the FEC is suspended, the device is detached. Upon resume failure,
the device is left in detached mode, possibly with some of the required
clocks not running. We don't want to be poking the device in that state
because as it may cause bus errors.
If the device is marked detached, avoid calling fec_stop().
This depends upon: "net:fec: improve safety of suspend/resume paths"
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should hold the rtnl lock while suspending, resuming or processing
the transmit timeout to ensure that nothing will interfere while we
bring up, take down or restart the hardware. The transmit timeout
could run if we're preempted during suspend.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
fec_enet_alloc_buffers() assumes that kmalloc() will never fail, which
is an invalid assumption. Fix this by implementing a common error
cleanup path, and use it to also clean up after failed bounce buffer
allocation.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that we do not double-free any allocations, and that any transmit
skbuffs are properly freed when we clean up the rings.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid writing any state until we're certain we can proceed with the
transmission: this avoids writing mapping error address values to the
descriptors, or setting the skbuff pointer until we have successfully
mapped the skb.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate, and then map the receive skb before writing any data to the
ring descriptor or storing the skb. When freeing the receive ring
entries, unmap and free the skb, and then clear the stored skb pointer.
This means we have ring data and skb pointer in one of two states:
either both fully setup, or nothing setup.
This simplifies the cleanup, as we can use just the skb pointer to
indicate whether the descriptor is setup, and thus avoids potentially
calling dma_unmap_single() on a DMA error value.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_disable() waits until the NAPI processing has completed, and then
prevents any further polls. At this point, the driver then clears
fep->opened. The NAPI poll function uses this to stop processing in
the receive path. Hence, it will never see this variable cleared,
because the NAPI poll has to complete before it will be cleared.
Therefore, this variable serves no purpose, so let's remove it.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the network interface goes down, stop the phy to prevent further
link up status changes before taking the MAC or netif sections down.
This prevents further reception of link up events which could
potentially call fec_restart().
Since phy_stop() takes the mutex which adjust_link() runs under, we
also ensure that adjust_link() will not already be processing a link
up event.
We also need to do this when suspending as well - we don't want a
mis-timed phy state change to restart the MAC after we have stopped
it for suspend, and thus need to restart the phy when resuming.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we disconnect from a phy, we should forget our pointer to it so we
don't accidentally try to configure it. We handle a NULL phy pointer
correctly in most places, except fec_enet_set_pauseparam(). Fix this
too.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
fep->phy_dev can not be NULL here for two reasons:
- fec_enet_open() will have successfully connected the phy, or will have
failed.
- fec_enet_open() will have called phy_start(fep->phy_dev), which
unconditionally dereferences this pointer.
If it were to be NULL here, then fec_enet_open() will have already
oopsed.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We use netif_stop_queue() in several places where we want to ensure that
the start_xmit function is not running. netif_stop_queue() is not
sufficient to achieve that - it merely sets a flag to indicate that the
transmit queue(s) should not be run.
netif_tx_disable() gives this guarantee, since it takes the transmit
queue lock while marking the queue stopped. This will wait for the
transmit function to complete before returning.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
While running: while :; do iperf -c <HOST> -P 4; done, transmit timeouts
are regularly reported. With the tx ring dumping in place, we can see
that all entries are in use, and the hardware has finished transmitting
these packets. However, the driver has not reclaimed these ring
entries.
This can occur if the interrupt handler is invoked at the wrong moment -
eg:
CPU0 CPU1
fec_enet_tx()
interrupt, IEVENT = FEC_ENET_TXF
FEC_ENET_TXF cleared
napi_schedule_prep()
napi_complete()
The result is that we clear the transmit interrupt, but we don't trigger
any cleaning of the transmit ring. Instead, use a different strategy:
- When receiving a transmit or receive interrupt, disable both tx and rx
interrupts, but do not acknowledge them. Schedule a napi poll. Don't
loop.
- When we are polled, read IEVENT, acknowledging the pending transmit
and receive interrupts, before then going on to process the
appropriate rings.
This allows us to avoid the race, and has a number of other advantages:
- we cut down on the number of transmit interrupts we have to process.
- we only look at the rings which have pending events.
- we gain additional throughput: the iperf total bandwidth increases
from about 180Mbps to 240Mbps:
[ 3] 0.0-10.0 sec 68.1 MBytes 57.0 Mbits/sec
[ 5] 0.0-10.0 sec 72.4 MBytes 60.5 Mbits/sec
[ 4] 0.0-10.1 sec 76.1 MBytes 63.5 Mbits/sec
[ 6] 0.0-10.1 sec 71.9 MBytes 59.9 Mbits/sec
[SUM] 0.0-10.1 sec 288 MBytes 241 Mbits/sec
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting the pause parameters causes a running network interface to be
restarted. However, the restart forces the FEC into half-duplex mode,
whether or not the remote end is in half-duplex mode. Misconfigured
duplex mode is a known source of problems on a link.
Fix this by always preserving the duplex mode on configuration changes.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The iMX6 gigabit FEC does not support half-duplex gigabit operation.
Phys attacked to the FEC may support this, and we currently do nothing
to disable this feature. This may result in an invalid configuration.
Mask out phy support for gigabit half-duplex operation.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 96c50caa51 (net: fec: Enable IP header hardware checksum)
enable HW IP header checksum for IPV4 and IPV6, which causes IPV6 TCP/UDP
cannot work. (The issue is reported by Russell King)
For FEC IP header checksum function: Insert IP header checksum. This "IINS"
bit is written by the user. If set, IP accelerator calculates the IP header
checksum and overwrites the IINS corresponding header field with the calculated
value. The checksum field must be cleared by user, otherwise the checksum
always is 0xFFFF.
So the previous patch clear IP header checksum field regardless of IP frame
type.
In fact, IP HW detect the packet as IPV6 type, even if the "IINS" bit is set,
the IP accelerator is not triggered to calculates IPV6 header checksum because
IPV6 frame format don't have checksum.
So this results in the IPV6 frame being corrupted.
The patch just add software detect the current packet type, if it is IPV6
frame, it don't clear IP header checksum field.
Cc: Russell King <linux@arm.linux.org.uk>
Reported-and-tested-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add software TSO support for FEC.
This feature allows to improve outbound throughput performance.
Tested on imx6dl sabresd board, running iperf tcp tests shows:
- 16.2% improvement comparing with FEC SG patch
- 82% improvement comparing with NO SG & TSO patch
$ ethtool -K eth0 tso on
$ iperf -c 10.192.242.167 -t 3 &
[ 3] local 10.192.242.108 port 35388 connected with 10.192.242.167 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0- 3.0 sec 181 MBytes 506 Mbits/sec
During the testing, CPU loading is 30%.
Since imx6dl FEC Bandwidth is limited to SOC system bus bandwidth, the
performance with SW TSO is a milestone.
CC: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: David Laight <David.Laight@ACULAB.COM>
CC: Li Frank <B20596@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Scatter/gather support for FEC.
This feature allows to improve outbound throughput performance.
Tested on imx6dl sabresd board:
Running iperf tests shows a 55.4% improvement.
$ ethtool -K eth0 sg off
$ iperf -c 10.192.242.167 -t 3 &
[ 3] local 10.192.242.108 port 52618 connected with 10.192.242.167 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0- 3.0 sec 99.5 MBytes 278 Mbits/sec
$ ethtool -K eth0 sg on
$ iperf -c 10.192.242.167 -t 3 &
[ 3] local 10.192.242.108 port 52617 connected with 10.192.242.167 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0- 3.0 sec 154 MBytes 432 Mbits/sec
CC: Li Frank <B20596@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support SG, software TSO, let's increase BD entry number.
CC: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to enhance the code readable, let's factorize the
feature list.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IP header checksum is calcalated by network layer in default.
To support software TSO, it is better to use HW calculate the
IP header checksum.
FEC hw checksum feature request the checksum field in frame
is zero, otherwise the calculative CRC is not correct.
For segmentated TCP packet, HW calculate the IP header checksum again,
it doesn't bring any impact. For SW TSO, HW calculated checksum bring
better performance.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the code more readable and easy to support other features like
SG, TSO, moving the common transmit function to one api.
And the patch also factorize the getting BD index to it own function.
CC: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5bbde4d2ec ("net: fec: use pinctrl PM helpers") caused the following
build error on m68k:
drivers/net/ethernet/freescale/fec_main.c: In function 'fec_enet_open':
drivers/net/ethernet/freescale/fec_main.c:1819:2: error: implicit declaration of function 'pinctrl_pm_select_default_state' [-Werror=implicit-function-declaration]
drivers/net/ethernet/freescale/fec_main.c: In function 'fec_enet_close':
drivers/net/ethernet/freescale/fec_main.c:1863:2: error: implicit declaration of function 'pinctrl_pm_select_sleep_state' [-Werror=implicit-function-declaration]
In order to fix the build error, include the linux/pinctrl/consumer.h header
file.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when system suspend, need to set pins to low power state to
save IO power consumption, there are three states of pinctrl:
"default", "idle" and "sleep". Currently enet supports default
and sleep state.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since imx serials FEC/ENET MDIO clock source is internal ipg clock,
and "ahb" clock is defined as FEC/ENET bus clock, so the patch just
correct the fec driver MDIO clock source.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Frank Li <frank.li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add below clock management to save fec power:
- After probe, disable all clocks incluing ipg, ahb, enet_out, ptp clock.
- Open ethx interface enable necessary clocks.
Close ethx interface disable all clocks.
The patch also encapsulates the all enet clocks enable/disable to
.fec_enet_clk_enable(), which can reduce the repetitional code in
driver.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Frank Li <Frank.li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Though we made sure to acquire a valid MAC for
the netdevice we never actually programmed it
into the hardware.
So if the bootloader did not set the MAC,
network operation would only work if userspace
explicitly asked to transfer the MAC to hardware.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
fec_enet_mdio_reset() does nothing useful and is optional for the MDIO
bus code, so let's just remove it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace kfree_skb with dev_kfree_skb_any in fec_enet_start_xmit that
can be called in hard irq and other contexts, when the packet is
dropped.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
If the Freescale fec is in promiscuous mode and network cable is
reconnected then the promiscuous mode get lost. The problem is caused
by a too soon call of set_multicast_list to re-enable promisc mode.
The FEC_R_CNTRL register changes are overwritten by fec_restart.
This patch fixes this by moving the call behind the init of FEC_R_CNTRL
register in fec_restart.
Successful tested on a i.MX28 board.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current flow: Set TX BD ready, and then set "INT" and "PINS" bit to
enable tx interrupt generation and crc checksum.
There has potential issue like as:
CPU fec uDMA
Set tx ready bit
uDMA start the BD transmission
Set "INT" bit
Set "PINS" bit
...
Above situation cause fec tx interrupt lost and fec MAC don't do
CRC checksum. The patch fix the potential issue.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Frank Li <Frank.li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If napi is left enabled after a failed attempt to bring the interface
up, we BUG:
fec 2188000.ethernet eth0: no PHY, assuming direct connection to switch
libphy: PHY fixed-0:00 not found
fec 2188000.ethernet eth0: could not attach to PHY
------------[ cut here ]------------
kernel BUG at include/linux/netdevice.h:502!
Internal error: Oops - BUG: 0 [#1] SMP ARM
...
PC is at fec_enet_open+0x4d0/0x500
LR is at __dev_open+0xa4/0xfc
Only enable napi after we are past all the failure paths.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
This covers everything under drivers/net except for wireless, which
has been submitted separately.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c
net/ipv6/ip6_tunnel.c
net/ipv6/ip6_vti.c
ipv6 tunnel statistic bug fixes conflicting with consolidation into
generic sw per-cpu net stats.
qlogic conflict between queue counting bug fix and the addition
of multiple MAC address support.
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to keep DT compatibility we need to revert this, otherwise the original
dts files will no longer work with this driver change.
This reverts commit 7a399e3a2e.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should not assume that the PHY reset is always active low.
Retrieve this information from the device tree instead, so that the PHY reset
can work on both cases.
Reported-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_tx_timestamp(skb) should be called _before_ TX completion
has a chance to trigger, otherwise it is too late and we access
freed memory.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: de5fb0a053 ("net: fec: put tx to napi poll function to fix dead lock")
Cc: Frank Li <Frank.Li@freescale.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/intel/i40e/i40e_main.c
drivers/net/macvtap.c
Both minor merge hassles, simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 031916568a worked around
errata ERR006358, but comment contains duplicated lines, impairing
the readability. Remove them.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings says:
====================
SIOCGHWTSTAMP ioctl
1. Add the SIOCGHWTSTAMP ioctl and update the timestamping
documentation.
2. Implement SIOCGHWTSTAMP in most drivers that support SIOCSHWTSTAMP.
3. Add a test program to exercise SIOC{G,S}HWTSTAMP.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
On tx submit the driver always dma_map_single() FEC_ENET_TX_FRSIZE (=2048)
bytes. This works because we don't overwrite any memory after the data buffer,
we remove it from cache if it was there. So we hurt performace in case the
mapping of a smaller area makes a difference.
There is also a bug: If the data area starts shortly before the end of
RAM say 0xc7fffa10 and the RAM ends at 0xc8000000 then we have enough
space to fit the data area (according to skb->len) but we would map beyond
end of ram if we are using 2048. In v2.6.31 (against which kernel this patch
made) there is the following check in dma_cache_maint():
|BUG_ON(!virt_addr_valid(start) || !virt_addr_valid(start + size - 1));
Since the area starting at 0xc8000000 is no longer virt_addr_valid() we
BUG() during dma_map_single(). The BUG() statement was removed in v3.5-rc1 as
per 2dc6a016 ("ARM: dma-mapping: use asm-generic/dma-mapping-common.h").
This patch was tested on v2.6.31 and then forward-ported and compile
tested only against the net tree. I think it is still worth fixing
mainline even after the BUG() statement is gone.
Tested-by: Fugang Duan <B38611@freescale.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver fails to check the results of DMA mapping and results in
the following warning: (with kernel config "CONFIG_DMA_API_DEBUG" enable)
------------[ cut here ]------------
WARNING: at lib/dma-debug.c:937 check_unmap+0x43c/0x7d8()
fec 2188000.ethernet: DMA-API: device driver failed to check map
error[device address=0x00000000383a8040] [size=2048 bytes] [mapped as single]
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.10.17-16827-g9cdb0ba-dirty #188
[<80013c4c>] (unwind_backtrace+0x0/0xf8) from [<80011704>] (show_stack+0x10/0x14)
[<80011704>] (show_stack+0x10/0x14) from [<80025614>] (warn_slowpath_common+0x4c/0x6c)
[<80025614>] (warn_slowpath_common+0x4c/0x6c) from [<800256c8>] (warn_slowpath_fmt+0x30/0x40)
[<800256c8>] (warn_slowpath_fmt+0x30/0x40) from [<8026bfdc>] (check_unmap+0x43c/0x7d8)
[<8026bfdc>] (check_unmap+0x43c/0x7d8) from [<8026c584>] (debug_dma_unmap_page+0x6c/0x78)
[<8026c584>] (debug_dma_unmap_page+0x6c/0x78) from [<8038049c>] (fec_enet_rx_napi+0x254/0x8a8)
[<8038049c>] (fec_enet_rx_napi+0x254/0x8a8) from [<804dc8c0>] (net_rx_action+0x94/0x160)
[<804dc8c0>] (net_rx_action+0x94/0x160) from [<8002c758>] (__do_softirq+0xe8/0x1d0)
[<8002c758>] (__do_softirq+0xe8/0x1d0) from [<8002c8e8>] (do_softirq+0x4c/0x58)
[<8002c8e8>] (do_softirq+0x4c/0x58) from [<8002cb50>] (irq_exit+0x90/0xc8)
[<8002cb50>] (irq_exit+0x90/0xc8) from [<8000ea88>] (handle_IRQ+0x3c/0x94)
[<8000ea88>] (handle_IRQ+0x3c/0x94) from [<8000855c>] (gic_handle_irq+0x28/0x5c)
[<8000855c>] (gic_handle_irq+0x28/0x5c) from [<8000de00>] (__irq_svc+0x40/0x50)
Exception stack(0x815a5f38 to 0x815a5f80)
5f20: 815a5f80 3b9aca00
5f40: 0fe52383 00000002 0dd8950e 00000002 81e7b080 00000000 00000000 815ac4d8
5f60: 806032ec 00000000 00000017 815a5f80 80059028 8041fc4c 60000013 ffffffff
[<8000de00>] (__irq_svc+0x40/0x50) from [<8041fc4c>] (cpuidle_enter_state+0x50/0xf0)
[<8041fc4c>] (cpuidle_enter_state+0x50/0xf0) from [<8041fd94>] (cpuidle_idle_call+0xa8/0x14c)
[<8041fd94>] (cpuidle_idle_call+0xa8/0x14c) from [<8000edac>] (arch_cpu_idle+0x10/0x4c)
[<8000edac>] (arch_cpu_idle+0x10/0x4c) from [<800582f8>] (cpu_startup_entry+0x60/0x130)
[<800582f8>] (cpu_startup_entry+0x60/0x130) from [<80bc7a48>] (start_kernel+0x2d0/0x328)
[<80bc7a48>] (start_kernel+0x2d0/0x328) from [<10008074>] (0x10008074)
---[ end trace c6edec32436e0042 ]---
Because dma-debug add new interfaces to debug dma mapping errors, pls refer
to: http://lwn.net/Articles/516640/
After dma mapping, it must call dma_mapping_error() to check mapping error,
otherwise the map_err_type alway is MAP_ERR_NOT_CHECKED, check_unmap() define
the mapping is not checked and dump the error msg. So,add dma_mapping_error()
checking to fix the WARNING
And RX DMA buffers are used repeatedly and the driver copies it into an skb,
fec_enet_rx() should not map or unmap, use dma_sync_single_for_cpu()/dma_sync_single_for_device()
instead of dma_map_single()/dma_unmap_single().
There have another potential issue: fec_enet_rx() passes the DMA address to __va().
Physical and DMA addresses are *not* the same thing. They may differ if the device
is behind an IOMMU or bounce buffering was required, or just because there is a fixed
offset between the device and host physical addresses. Also fix it in this patch.
=============================================
V2: add net_ratelimit() to limit map err message.
use dma_sync_single_for_cpu() instead of dma_map_single().
fix the issue that pass DMA addresses to __va() to get virture address.
V1: initial send
=============================================
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/freescale/fec_main.c
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
net/bridge/br_multicast.c
net/ipv6/sit.c
The conflicts were minor:
1) sit.c changes overlap with change to ip_tunnel_xmit() signature.
2) br_multicast.c had an overlap between computing max_delay using
msecs_to_jiffies and turning MLDV2_MRC() into an inline function
with a name using lowercase instead of uppercase letters.
3) stmmac had two overlapping changes, one which conditionally allocated
and hooked up a dma_cfg based upon the presence of the pbl OF property,
and another one handling store-and-forward DMA made. The latter of
which should not go into the new of_find_property() basic block.
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug: error to get the previous BD entry. When the current BD
is the first BD, the previous BD entry must be the last BD,
not "bdp - 1" in current logic.
V4:
* Optimize fec_enet_get_nextdesc() for code clean.
Replace "ex_new_bd - ring_size" with "ex_base".
Replace "new_bd - ring_size" with "base".
V3:
* Restore the API name because David suggest to use fec_enet_
prefix for all function in fec driver.
So, change next_bd() -> fec_enet_get_nextdesc()
change pre_bd() -> fec_enet_get_prevdesc()
* Reduce the two APIs parameters for easy to call.
V2:
* Add tx_ring_size and rx_ring_size to struct fec_enet_private.
* Replace api fec_enet_get_nextdesc() with next_bd().
Replace api fec_enet_get_prevdesc() with pre_bd().
* Move all ring size check logic to next_bd() and pre_bd(), which
simplifies the code redundancy.
V1:
* Add BD ring size check to get the previous BD entry in correctly.
Reviewed-by: Li Frank <B20596@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Frank Li <frank.li@freescale.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit dc975382 "net: fec: add napi support to improve proformance"
converted the fec driver to the napi model. However, that commit
forgot to remove the call to skb_defer_rx_timestamp which is only
needed in non-napi drivers.
(The function napi_gro_receive eventually calls netif_receive_skb,
which in turn calls skb_defer_rx_timestamp.)
This patch should also be applied to the 3.9 and 3.10 kernels.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My static checker complains that on some arches unsigned longs can be 8
characters which is larger than the buffer is only 6 chars.
Additionally, Ben Hutchings points out that the buffer actually holds
big endian data and the buffer we are reading from is CPU endian.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using a custom 'FEC_NAPI_WEIGHT', just use the generic
'NAPI_POLL_WEIGHT' definition instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't test for having link and let hardware deal with this situation.
Without this patch I see a machine running an -rt patched Linux being
stuck in sch_direct_xmit when it looses link while there is still a
packet to be sent. In this case the fec_enet_start_xmit routine returned
NETDEV_TX_BUSY which makes the network stack reschedule the packet and
so sch_direct_xmit calls fec_enet_start_xmit again.
I failed to reproduce a complete hang without -rt, but I think the
problem exists there, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the ready bit in the transmit buffer descriptor (TxBD[R])
is previously detected as not set during a prior frame transmission,
then the ENET_TDAR[TDAR] bit is cleared at a later time, even if
additional TxBDs were added to the ring and the ENET_TDAR[TDAR]
bit is set. This results in frames not being transmitted until
there is a 0-to-1 transition on ENET_TDAR[TDAR].
Workarounds:
code can use the transmit frame interrupt flag (ENET_EIR[TXF])
as a method to detect whether the ENET has completed transmission
and the ENET_TDAR[TDAR] has been cleared. If ENET_TDAR[TDAR] is
detected as cleared when packets are queued and waiting for transmit,
then a write to the TDAR bit will restart TxBD processing.
This case main happen when loading is light. A ethernet package may
not send out utile next package put into tx queue.
How to test:
while [ true ]
do
ping <IP> -s 10000 -w 4
ping <IP> -s 6000 -w 2
ping <IP> -s 4000 -w 2
ping <IP> -s 10000 -w 2
done
You will see below result in overnight test.
6008 bytes from 10.192.242.116: seq=1 ttl=128 time=0.722 ms
4008 bytes from 10.192.242.116: seq=0 ttl=128 time=1001.008 ms
4008 bytes from 10.192.242.116: seq=1 ttl=128 time=1.010 ms
10008 bytes from 10.192.242.116: seq=0 ttl=128 time=0.896 ms
After apply this patch, >1000ms delay disappear.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MODULE_ALIAS, so that auto module loading can work.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using devm_request_irq() can make the code smaller and cleaner.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As devm_ioremap_resource() is used, there is no need to explicitely check the
return value from platform_get_resource(), as this is something that
devm_ioremap_resource() takes care by itself.
Also, place platform_get_resource() prior to devm_ioremap_resource() for
better code readability.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clk_prepare_enable() may fail, so let's check its return value and propagate it
in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clk_ptp should also be enabled in fec_resume() and disabled in fec_suspend().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On fec_probe the clocks are enabled in the following order:
clk_ahb -> clk_ipg -> clk_enet_out -> clk_ptp
, so in the error and remove paths we should disabled them in the opposite
order.
Also fix the order in the suspend/resume functions.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clk_enet_out and clk_ptp are optional clocks, so we should not enable/disable
them unconditionally.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables the driver to take advantage of the FEC VLAN
indicator to improve performance.
Signed-off-by: Jim Baxter <jim_baxter@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maciej S. Szmigiero