Commit Graph

275 Commits

Author SHA1 Message Date
Jean Delvare 01d56a6aa1 i2c-viapro: Add VIA VX900 device ID
The SMBus controller in the VIA VX900 appears to be compatible with
the VIA VX855, so just add the device ID.

This closes kernel bug #43096.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-10-05 22:23:53 +02:00
James Ralston 4a8f1ddde9 i2c-i801: Add Device IDs for Intel Lynx Point-LP PCH
Add the SMBus Device IDs for the Intel Lynx Point-LP PCH.

Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-09-10 10:14:02 +02:00
Daniel Kurtz 636752bcb5 i2c-i801: Enable IRQ for SMBus transactions
Add a new 'feature' to i2c-i801 to enable using PCI interrupts.
When the feature is enabled, then an isr is installed for the device's
PCI IRQ.

An I2C/SMBus transaction is always terminated by one of the following
interrupt sources: FAILED, BUS_ERR, DEV_ERR, or on success: INTR.

When the isr fires for one of these cases, it sets the ->status variable
and wakes up the waitq.  The waitq then saves off the status code, and
clears ->status (in preparation for some future transaction).
The SMBus controller generates an INTR irq at the end of each
transaction where INTREN was set in the HST_CNT register.

No locking is needed around accesses to priv->status since all writes to
it are serialized: it is only ever set once in the isr at the end of a
transaction, and cleared while no interrupts can occur.  In addition, the
I2C adapter lock guarantees that entire I2C transactions for a single
adapter are always serialized.

For this patch, the INTREN bit is set only for SMBus block, byte and word
transactions, but not for I2C reads or writes.  The use of the DS
(BYTE_DONE) interrupt with byte-by-byte I2C transactions is implemented in
a subsequent patch.

The interrupt feature has only been enabled for COUGARPOINT hardware.
In addition, it is disabled if SMBus is using the SMI# interrupt.

Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-07-24 14:13:58 +02:00
Jean Delvare 9cd3f2e849 i2c/writing-clients: Mention module_i2c_driver()
Based on a previous patch from Peter Meerwald.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Peter Meerwald <p.meerwald@bct-electronic.com>
2012-07-24 14:13:57 +02:00
Andrew Armenia 2a2f7404a1 i2c-piix4: Support AMD auxiliary SMBus controller
Some AMD chipsets, such as the SP5100, have an auxiliary SMBus
controller with a second set of registers. This patch adds
support for this auxiliary controller.

Tested on ASUS KCMA-D8 motherboard.

Signed-off-by: Andrew Armenia <andrew@asquaredlabs.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-07-24 14:13:57 +02:00
Mark Brown 14674e7011 i2c: Split I2C_M_NOSTART support out of I2C_FUNC_PROTOCOL_MANGLING
Since there are uses for I2C_M_NOSTART which are much more sensible and
standard than most of the protocol mangling functionality (the main one
being gather writes to devices where something like a register address
needs to be inserted before a block of data) create a new I2C_FUNC_NOSTART
for this feature and update all the users to use it.

Also strengthen the disrecommendation of the protocol mangling while we're
at it.

In the case of regmap-i2c we remove the requirement for mangling as
I2C_M_NOSTART is the only mangling feature which is being used.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-05-30 10:55:34 +02:00
Jean Delvare e7065e20d9 i2c: Rename last mux driver to standard pattern
Update the MAINTAINERS entry and all other references accordingly.

Based on an original patch by Wolfram Sang.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com>

[wsa: fixed merge conflict due to rework in i2c_add_mux_adapter()]

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-05-12 14:28:18 +02:00
Lucas De Marchi 970e248649 Documentation: remove references to /etc/modprobe.conf
Usage of /etc/modprobe.conf file was deprecated by module-init-tools and
is no longer parsed by new kmod tool. References to this file are
replaced in Documentation, comments and Kconfig according to the
context.

There are also some references to the old /etc/modules.conf from 2.4
kernels that are being removed.

Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2012-03-30 16:03:15 -07:00
Seth Heasley 062737fb6d i2c-i801: Add device IDs for Intel Lynx Point
Add the SMBus controller device IDs for the Intel Lynx Point PCH.

Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-03-26 21:47:19 +02:00
Roland Stigge 286431048b USB: ohci-nxp: Rename symbols from pnx4008 to nxp
Since this driver is compatible with several NXP devices, the driver was renamed
accordingly. This patch also changes the respective symbol names.

Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-03-13 14:27:28 -07:00
Jean Delvare cbb4451404 i2c: Fix device name for 10-bit slave address
10-bit addresses overlap with traditional 7-bit addresses, leading in
device name collisions. Add an arbitrary offset to 10-bit addresses to
prevent this collision. The offset was chosen so that the address is
still easily recognizable.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
2011-11-23 11:33:07 +01:00
Jonathan Cameron 06a67848c6 i2c: Functions for byte-swapped smbus_write/read_word_data
Reimplemented at least 17 times discounting error mangling cases
where it could be used.

Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2011-10-30 13:47:25 +01:00
Seth Heasley 6e2a851e71 i2c-i801: SMBus patch for Intel Panther Point DeviceIDs
This patch adds the SMBus controller DeviceID for the Intel Panther Point PCH.

Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2011-05-24 20:58:49 +02:00
Vikram Narayanan 3116c86033 i2c/writing-clients: Fix foo_driver.id_table
The i2c_device_id structure variable's name is not used in the
i2c_driver structure.

Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2011-05-24 20:58:48 +02:00
Lucas De Marchi 25985edced Fix common misspellings
Fixes generated by 'codespell' and manually reviewed.

Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
2011-03-31 11:26:23 -03:00
Linus Torvalds 75ea6358bc Merge branch 'for-linus/2639/i2c-2' of git://git.fluff.org/bjdooks/linux
* 'for-linus/2639/i2c-2' of git://git.fluff.org/bjdooks/linux:
  i2c-pxa2xx: Don't clear isr bits too early
  i2c-pxa2xx: Fix register offsets
  i2c-pxa2xx: pass of_node from platform driver to adapter and publish
  i2c-pxa2xx: check timeout correctly
  i2c-pxa2xx: add support for shared IRQ handler
  i2c-pxa2xx: Add PCI support for PXA I2C controller
  ARM: pxa2xx: reorganize I2C files
  i2c-pxa2xx: use dynamic register layout
  i2c-mxs: set controller to pio queue mode after reset
  i2c-eg20t: support new device OKI SEMICONDUCTOR ML7213 IOH
  i2c/busses: Add support for Diolan U2C-12 USB-I2C adapter
2011-03-22 10:05:27 -07:00
Seth Heasley 662cda8abb i2c-i801: SMBus patch for Intel DH89xxCC DeviceIDs
Add the SMBus Controller DeviceIDs for the Intel DH89xxCC PCH.

Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2011-03-20 14:50:53 +01:00
Jean Delvare ed065e26b8 i2c: Minor fixes to upgrading-clients document
* Typical legacy drivers implemented method .detach_client, not
  .detach_adapter.
* Drop all references to __devexit, as i2c drivers shouldn't use it.

Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2011-03-20 14:50:52 +01:00
Roman Fietze 6ced9e6b39 i2c: Fix typo in instantiating-devices document
The struct i2c_board_info member holding the name is "type", not
"name".

Signed-off-by: Roman Fietze <roman.fietze@telemotive.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
2011-03-20 14:50:52 +01:00
Guenter Roeck 335d7c58fc i2c/busses: Add support for Diolan U2C-12 USB-I2C adapter
This patch adds support for the Diolan U2C-12 USB-I2C adapter.
It also updates MAINTAINERS to list the author as maintainer.

Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2011-01-27 00:39:30 +00:00
Peter Korsgaard 92ed1a76ca i2c: Add generic I2C multiplexer using GPIO API
Add an i2c mux driver providing access to i2c bus segments using a
hardware MUX sitting on a master bus and controlled through gpio pins.

E.G. something like:

  ----------              ----------  Bus segment 1   - - - - -
 |          | SCL/SDA    |          |-------------- |           |
 |          |------------|          |
 |          |            |          | Bus segment 2 |           |
 |  Linux   | GPIO 1..N  |   MUX    |---------------   Devices
 |          |------------|          |               |           |
 |          |            |          | Bus segment M
 |          |            |          |---------------|           |
  ----------              ----------                  - - - - -

SCL/SDA of the master I2C bus is multiplexed to bus segment 1..M
according to the settings of the GPIO pins 1..N.

Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2011-01-10 22:11:23 +01:00
David Woodhouse 55fee8d7f7 i2c-i801: Add PCI idents for Patsburg 'IDF' SMBus controllers
These are the extra 'Integrated Device Function' SMBus controllers found
on the Patsburg chipset. Mention the absence of slave mode support.

Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-31 21:07:00 +01:00
Seth Heasley e30d9859cf i2c-i801: Add Intel Patsburg device ID
Add support for the Intel Patsburg PCH SMBus Controller.

Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-31 21:06:59 +01:00
Jean Delvare 9a94241afc i2c: Add support for custom probe function
The probe method used by i2c_new_probed_device() may not be suitable
for all cases. Let the caller provide its own, optional probe
function.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2010-08-11 18:20:56 +02:00
Justin P. Mattock 0ea6e61122 Documentation: update broken web addresses.
Below you will find an updated version from the original series bunching all patches into one big patch
updating broken web addresses that are located in Documentation/*
Some of the addresses date as far far back as 1995 etc... so searching became a bit difficult,
the best way to deal with these is to use web.archive.org to locate these addresses that are outdated.
Now there are also some addresses pointing to .spec files some are located, but some(after searching
on the companies site)where still no where to be found. In this case I just changed the address
to the company site this way the users can contact the company and they can locate them for the users.

Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Cc: Paulo Marques <pmarques@grupopie.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Michael Neuling <mikey@neuling.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2010-08-04 15:21:40 +02:00
Andrea Gelmini 89140f4157 Documentation/i2c: Checkpatch cleanup
Remove all trailing whitespace in Documentation/i2c.

Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-06-03 11:33:50 +02:00
Jean Delvare adff687d8c i2c-i801: Let the user disable selected driver features
Let the user disable selected features normally supported by the
device. This makes it possible to work around possible driver or
hardware bugs if the feature in question doesn't work as intended
for whatever reason.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Felix Rubinstein <felixru@gmail.com>
2010-05-21 18:40:54 +02:00
Wolfram Sang e4a7b9b04d i2c-core: Erase pointer to clientdata on removal
After discovering that a lot of i2c-drivers leave the pointer to their
clientdata dangling, it was decided to let the core handle this issue.
It is assumed that the core may access the private data after remove()
as there are no guarantees for the lifetime of such pointers anyhow (see
thread starting at http://lkml.org/lkml/2010/3/21/68)

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-05-04 11:09:27 +02:00
Zhangfei Gao 0c43ea544c i2c: Document the message size limit
i2c_master_send & i2c_master_recv do not support more than 64 kb
transfer, since msg.len is u16.

Signed-off-by: Zhangfei Gao <zgao6@marvell.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-03-02 12:23:49 +01:00
Jean Delvare 927ab2f807 i2c-parport-light: Add SMBus alert support
Add support for the SMBus alert mechanism to the i2c-parport-light
driver. The ADM1032 evaluation board at least is properly wired for
this.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Trent Piepho <tpiepho@freescale.com>
2010-03-02 12:23:45 +01:00
Jean Delvare 3585925448 i2c-parport: Add SMBus alert support
Add support for the SMBus alert mechanism to the i2c-parport driver.
The ADM1032 evaluation board at least is properly wired for this.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Trent Piepho <tpiepho@freescale.com>
2010-03-02 12:23:44 +01:00
Jean Delvare b5527a7766 i2c: Add SMBus alert support
SMBus alert support. The SMBus alert protocol allows several SMBus
slave devices to share a single interrupt pin on the SMBus master,
while still allowing the master to know which slave triggered the
interrupt.

This is based on preliminary work by David Brownell. The key
difference between David's implementation and mine is that his was
part of i2c-core, while mine is split into a separate, standalone
module named i2c-smbus. The i2c-smbus module is meant to include
support for all SMBus extensions to the I2C protocol in the future.

The benefit of this approach is a zero cost for I2C bus segments which
do not need SMBus alert support. Where David's implementation
increased the size of struct i2c_adapter by 7% (40 bytes on i386),
mine doesn't touch it. Where David's implementation added over 150
lines of code to i2c-core (+10%), mine doesn't touch it. The only
change that touches all the users of the i2c subsystem is a new
callback in struct i2c_driver (common to both implementations.) I seem
to remember Trent was worried about the footprint of David'd
implementation, hopefully mine addresses the issue.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Trent Piepho <tpiepho@freescale.com>
2010-03-02 12:23:42 +01:00
Seth Heasley 393764340b i2c-i801: Add Intel Cougar Point device IDs
Add the Intel Cougar Point (PCH) SMBus controller device IDs.

Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-03-02 12:23:39 +01:00
Jean Delvare c3813d6af1 i2c: Get rid of struct i2c_client_address_data
Struct i2c_client_address_data only contains one field at this point,
which makes its usefulness questionable. Get rid of it and pass simple
address lists around instead.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
2009-12-14 21:17:25 +01:00
Jean Delvare 6471b68982 i2c-stub: Documentation update
There is nothing sensors-specific to i2c-stub.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-12-06 17:06:30 +01:00
Jean Delvare 38f41f282f i2c-stub: Allow user to disable some commands
Add a module parameter to override the functionality bitfield. This
lets the user disable some commands. This can be used to force a chip
driver to take different code paths.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-12-06 17:06:29 +01:00
Jean Delvare 4710317891 i2c-stub: Implement I2C block support
This is required to test some drivers, for example at24.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-12-06 17:06:28 +01:00
Jean Delvare c7b25a9e96 i2c: Drop probe, ignore and force module parameters
The legacy probe and force module parameters are obsolete now, the
same can be achieved using the new_device sysfs interface, which is
both more flexible and cheaper (it is implemented by i2c-core rather
than replicated in every driver module.)

The legacy ignore module parameters can be dropped as well. Ignoring
can be done by instantiating a "dummy" device at the problematic
address.

This is the first step of a huge cleanup to i2c-core's i2c_detect
function, i2c.h's I2C_CLIENT_INSMOD* macros, and all drivers that made
use of them.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-12-06 17:06:24 +01:00
Jean Delvare a0c11cdd6a i2c-voodoo3: Delete
Superseded by tdfxfb. I2C/DDC support used to live in a separate
driver but this caused driver conflicts.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
2009-12-06 17:06:21 +01:00
Crane Cai 3806e94b01 i2c-piix4: Modify code name SB900 to Hudson-2
Change SB900 to its formal code name Hudson-2.

Signed-off-by: Crane Cai <crane.cai@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-11-07 13:10:46 +01:00
Jean Delvare 03f1805ad0 i2c: Minor documentation update
The sysfs path to i2c adapters has changed recently, update the
documentation to reflect that change.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-10-04 22:53:45 +02:00
Jean Delvare f546c65cd5 i2c: Move misc devices documentation
Some times ago the eeprom and max6875 drivers moved to
drivers/misc/eeprom, but their documentation did not follow. It's
finally time to get rid of Documentation/i2c/chips.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Ben Gardner <gardner.ben@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
2009-10-04 22:53:40 +02:00
Crane Cai 76b3e28fa7 i2c-piix4: Add AMD SB900 SMBus device ID
Add new SMBus device ID for AMD SB900.

Signed-off-by: Crane Cai <crane.cai@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-09-18 22:45:50 +02:00
Wolfram Sang e7c5c49ecd i2c/chips: Remove deprecated pcf8574 driver
The pcf8574 driver in drivers/i2c/chips which just exports its register to
sysfs is superseded by drivers/gpio/pcf857x.c which properly uses the gpiolib.
As this driver has been deprecated for more than a year, finally remove it.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-09-18 22:45:49 +02:00
Wolfram Sang 732d481127 i2c/chips: Remove deprecated pca9539 driver
The pca9539 driver in drivers/i2c/chips which just exports its registers to
sysfs is superseded by drivers/gpio/pca953x.c which properly uses the gpiolib.
As this driver has been deprecated for more than a year, finally remove it.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Ben Gardner <gardner.ben@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-09-18 22:45:48 +02:00
Wolfram Sang 8f67eeb0b4 i2c/chips: Remove deprecated pcf8575 driver
The pcf8575 driver in drivers/i2c/chips which just exports its register to
sysfs is superseded by drivers/gpio/pcf857x.c which properly uses the gpiolib.
As this driver has been deprecated for more than a year, finally remove it.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Bart Van Assche <bart.vanassche@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-09-18 22:45:48 +02:00
Jean Delvare 99cd8e2587 i2c: Add a sysfs interface to instantiate devices
Add a sysfs interface to instantiate and delete I2C devices. This is
primarily a replacement of the force_* module parameters implemented
by some i2c drivers. These module parameters were implemented
internally by the I2C_CLIENT_INSMOD* macros, which don't scale well.

This can also be used when developing a driver on a self-soldered
board which doesn't yet have proper I2C device declaration at the
platform level, and presumably for various debugging situations.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
2009-06-19 16:58:20 +02:00
Jean Delvare 729d6dd571 i2c: Get rid of the legacy binding model
We converted all the legacy i2c drivers so we can finally get rid of
the legacy binding model. Hooray!

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
2009-06-19 16:58:18 +02:00
Harald Welte a231591f04 i2c-viapro: Add new PCI device ID for VX855
The south bridge of the VIA VX855 chipset has a different PCI Device ID
so i2c-viapro.c needs to be updated with this.

Signed-off-by: Harald Welte <HaraldWelte@viatech.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-06-15 18:01:49 +02:00
Richard Röjfors dd14be4c27 i2c-ocores: Can add I2C devices to the bus
There is sometimes a need for the ocores driver to add devices to the
bus when installed.

i2c_register_board_info can not always be used, because the I2C devices
 are not known at an early state, they could for instance be connected
 on a I2C bus on a PCI device which has the Open Cores IP.

i2c_new_device can not be used in all cases either since the resulting
bus nummer might be unknown.

The solution is the pass a list of I2C devices in the platform data to
the Open Cores driver. This is useful for MFD drivers.

Signed-off-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-06-13 10:39:28 +01:00
Jean Delvare fb4504fe84 Move the pcf8591 driver to hwmon
Directory drivers/i2c/chips is going away, so drivers there must find
new homes. For the pcf8591 driver, the best choice seems to be the
hwmon subsystem. While the Philips PCF8591 device isn't a typical
hardware monitoring chip, its DAC interface is compatible with the
hwmon one, so it fits somewhat.

If a better subsystem is ever created for ADC/DAC chips, the driver
could be moved there.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>
2009-03-30 21:46:43 +02:00
Flavio Leitner 506a8b6c27 i2c-piix4: Add support for the Broadcom HT1100 chipset
Add support for the Broadcom HT1100 LD chipset (SMBus function.)

Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-03-28 21:34:46 +01:00
Jean Delvare d2dd14ac18 i2c-nforce2: Add support for MCP67, MCP73, MCP78S and MCP79
The MCP78S and MCP79 appear to be compatible with the previous nForce
chips as far as the SMBus controller is concerned. The MCP67 and MCP73
were not tested yet but I'd be very surprised if they weren't
compatible too.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Oleg Ryjkov <olegr@olegr.ca>
Cc: Malcolm Lalkaka <mlalkaka@gmail.com>
Cc: Zbigniew Luszpinski <zbiggy@o2.pl>
2009-03-28 21:34:41 +01:00
Jean Delvare 764c16918f i2c: Document the different ways to instantiate i2c devices
On popular demand, here comes some documentation about how to
instantiate i2c devices in the new (standard) i2c device driver
binding model.

I have also clarified how the class bitfield lets driver authors
control which buses are probed in the auto-detect case, and warned
more loudly against the abuse of this method.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Michael Lawnick <nospam_lawnick@gmx.de>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
2009-03-28 21:34:40 +01:00
Jean Delvare 846557d3ce i2c: The i2c mailing list is moving
Replace all references to the old i2c mailing list.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-30 15:55:47 +01:00
Jean Delvare 0e47858da4 i2c: Update and clean up writing-clients document
* Strip trailing white space.
* Remove out-of-date or irrelevant parts.
* Insist on the fact that command is deprecated.
* Fix spelling mistakes and typos.
* Reformat code examples and function prototypes to comply with the
  kernel coding style.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-22 20:21:32 +02:00
Jean Delvare e313353dd4 i2c: Delete legacy model documentation
The legacy i2c binding model is deprecated and will be removed soon,
so we no longer need to document it.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-22 20:21:31 +02:00
Jean Delvare 7d1d8999b4 i2c: Constify i2c_get_clientdata's parameter
i2c_get_clientdata doesn't change the i2c_client it is passed as a
parameter, so it can be constified. Same for i2c_get_adapdata.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-22 20:21:31 +02:00
Jean Delvare d955cafb5c i2c: Delete outdated client porting guide
The document describing how to port i2c chip drivers from Linux 2.4 to
Linux 2.6 is outdated. As I suspect that most drivers that had to be
ported have already been by now, I do not want to spend time updating
it. Let's just delete it instead.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-22 20:21:30 +02:00
Seth Heasley c429a247f5 i2c-i801: Add support for Intel Ibex Peak
Adds the Intel Ibex Peak (PCH) SMBus Controller Device IDs.

Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-22 20:21:29 +02:00
Prakash Mortha 596c88f460 i2c: Restore i2c_smbus_process_call function
Restore the i2c_smbus_process_call() as one driver (for the
Micronas MAP5401) will need it soon.

[JD: Update documentation accordingly.]

Signed-off-by: Prakash Mortha <pmortha@escient.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-14 17:30:06 +02:00
Jean Delvare 7c15fd1249 i2c: Document the implementation details of the /dev interface
I wrote this explanation to answer a question on the i2c mailing list,
and thought it would be good to have in the kernel documentation.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-14 17:30:05 +02:00
Jean Delvare fceb2d0680 i2c: Improve dev-interface documentation
* Clarify some points.
* Point developers to i2c-tools instead of lm_sensors.
* Fix coding style in code examples.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-14 17:30:05 +02:00
Rudolf Marek b806a71a0e i2c-viapro: Add VX800/VX820 support
Thanks to new datasheets published on http://linux.via.com.tw we can now add 
support for VX800/VX820 chipsets.

Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-14 17:30:03 +02:00
Ben Dooks 31321b76e1 i2c: Documentation: upgrading clients HOWTO
Add a document describing how i2c clients on Linux 2.6 can be
moved from the old to the new driver model.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2008-07-28 12:41:02 +01:00
Jean Delvare bd8d421f7c i2c: Convert the max6875 driver to a new-style i2c driver
The new-style max6875 driver implements the optional detect() callback
to cover the use cases of the legacy driver. I'm curious if anyone
really needs this though, so it might be removed in the feature.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-07-16 19:30:07 +02:00
Jean Delvare 3d63430a26 i2c: Convert the pca9539 driver to a new-style i2c driver
The new-style pca9539 driver implements the optional detect() callback
to cover the use cases of the legacy driver.

Warning: users will now have to use the force module parameter to get
the driver to attach to their device. That's not a bad thing as these
devices can't be detected anyway.

Note that this doesn't change the fact that this driver is deprecated
in favor of gpio/pca953x.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-07-16 19:30:07 +02:00
Jean Delvare 97addff6de i2c: Convert the pcf8575 driver to a new-style i2c driver
The new-style pcf8575 driver implements the optional detect() callback
to cover the use cases of the legacy driver.

Warning: users will now have to use the force module parameter to get
the driver to attach to their device. That's not a bad thing as these
devices can't be detected anyway.

Note that this doesn't change the fact that this driver is deprecated
in favor of gpio/pcf857x.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-07-16 19:30:06 +02:00
Jean Delvare 833bedb813 i2c: Convert the pcf8574 driver to a new-style i2c driver
The new-style pcf8574 driver implements the optional detect() callback
to cover the use cases of the legacy driver.

Warning: users will now have to use the force module parameter to get
the driver to attach to their device. That's not a bad thing as these
devices can't be detected anyway.

Note that this doesn't change the fact that this driver is deprecated
in favor of gpio/pcf857x.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-07-16 19:30:06 +02:00
Jean Delvare 4735c98f84 i2c: Add detection capability to new-style drivers
Add a mechanism to let new-style i2c drivers optionally autodetect
devices they would support on selected buses and ask i2c-core to
instantiate them. This is a replacement for legacy i2c drivers, much
cleaner.

Where drivers had to implement both a legacy i2c_driver and a
new-style i2c_driver so far, this mechanism makes it possible to get
rid of the legacy i2c_driver and implement both enumerated and
detected device support with just one (new-style) i2c_driver.

Here is a quick conversion guide for these drivers, step by step:

* Delete the legacy driver definition, registration and removal.
  Delete the attach_adapter and detach_client methods of the legacy
  driver.

* Change the prototype of the legacy detect function from
    static int foo_detect(struct i2c_adapter *adapter, int address, int kind);
  to
    static int foo_detect(struct i2c_client *client, int kind,
    			  struct i2c_board_info *info);

* Set the new-style driver detect callback to this new function, and
  set its address_data to &addr_data (addr_data is generally provided
  by I2C_CLIENT_INSMOD.)

* Add the appropriate class to the new-style driver. This is
  typically the class the legacy attach_adapter method was checking
  for. Class checking is now mandatory (done by i2c-core.) See
  <linux/i2c.h> for the list of available classes.

* Remove the i2c_client allocation and freeing from the detect
  function. A pre-allocated client is now handed to you by i2c-core,
  and is freed automatically.

* Make the detect function fill the type field of the i2c_board_info
  structure it was passed as a parameter, and return 0, on success. If
  the detection fails, return -ENODEV.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-07-14 22:38:36 +02:00
Jean Delvare 67c2e66571 i2c: Delete unused function i2c_smbus_write_quick
Function i2c_smbus_write_quick has no users left, so we can delete it.

Also update the list of these helper functions which are gone but
could be added back if needed.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-07-14 22:38:23 +02:00
David Brownell 24a5bb7b18 i2c-core: Return -Errno, not -1
More updates to the I2C stack's fault reporting:  make the core stop
returning "-1" (usually "-EPERM") for all faults.  Instead, pass lower
level fault code up the stack, or return some appropriate errno.

This patch happens to touch almost exclusively SMBus calls.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-07-14 22:38:23 +02:00
David Brownell 81fded1f79 i2c: Document standard fault codes
Create Documentation/i2c/fault-codes to help standardize
fault/error code usage in the I2C stack.  It turns out that
returning -1 (-EPERM) for everything was not at all helpful.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-07-14 22:38:22 +02:00
Adrian Bunk 20a9b6e7c3 i2c: Remove 3 deprecated bus drivers
This patch contains the scheduled removal of i2c-i810, i2c-prosavage
and i2c-savage4.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-07-14 22:38:22 +02:00
Ben Dooks 2260e63a2f i2c: Documentation: fix device matching description
The matching process described for new style clients in
Documentation/i2c/writing-clients is classed as out-of-date
as it requires the presence of an .id_table entry in the
driver's i2c_driver entry.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-07-01 22:38:18 +02:00
Jean Delvare 88b283281f i2c: Improve the functionality documentation
Attempt to make the documentation about the I2C/SMBus functionality
checking API clearer.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-05-11 20:37:05 +02:00
David Brownell 1a31a88f4f i2c: Improve smbus-protocol documentation
Improve the smbus-protocol documentation file somewhat:

 - Use the names of the SMBus protocol operations (from the 2.0
   specification), not made-up-for-Linux names.

 - Add the name of the call used to execute each operation ... and
   point out that there are mismatches, where functions execute
   different protocol operations than their names specify.
   
The most confusing examples are that "Read Byte" isn't executed by
i2c_smbus_read_byte(), and that "Write Byte" isn't executed by
i2c_smbus_write_byte().  When coding, that's not as bad as it may
seem; but that case would seem to be worth fixing.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-05-11 20:37:05 +02:00
Jean Delvare d2653e9273 i2c: Add support for device alias names
Based on earlier work by Jon Smirl and Jochen Friedrich.

This patch allows new-style i2c chip drivers to have alias names using
the official kernel aliasing system and MODULE_DEVICE_TABLE(). At this
point, the old i2c driver binding scheme (driver_name/type) is still
supported.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jochen Friedrich <jochen@scram.de>
Cc: Jon Smirl <jonsmirl@gmail.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
2008-04-29 23:11:39 +02:00
Gaston, Jason D d28dc71121 i2c-i801: Add support for the ICH10
Add the Intel ICH10 SMBus Controller DeviceID's and updates
Tolapai support.

Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-02-24 20:03:42 +01:00
Jean Delvare ec1d86c457 hwmon: Update the lm-sensors website address
It's about time to reflect the move of the lm-sensors project to
lm-sensors.org.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
2008-02-07 20:39:42 -05:00
eric miao b72540c30c deprecate obsolete pca9539 driver
Use drivers/gpio/pca9539.c instead.

Signed-off-by: eric miao <eric.miao@marvell.com>
Acked-by: Ben Gardner <bgardner@wabtec.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 09:44:13 -08:00
Jean Delvare 0d227a7e72 i2c-viapro: Add support for the VT8237S
Add support for another variant of the VT8237. I couldn't test
I2C block support but I assume it is present as well.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-01-27 18:14:51 +01:00
Jean Delvare 6342064cad i2c-i801: Implement I2C block read support
I2C block read is supported since the ICH5. I couldn't get it to work
using the block buffer, so it's using the old-style byte-by-byte mode
for now.

Note: I'm also updating the driver author... The i2c-i801 driver was
really written by Mark Studebaker, even though he based his work on
the i2c-piix4 driver which was written by Philip Edelbrock.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-01-27 18:14:50 +01:00
Jean Delvare 2cdddeb8d7 i2c: normal_i2c can be made const (remaining drivers)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-01-27 18:14:47 +01:00
Jean Delvare 569be443e3 i2c-stub: Use a single array for byte and word operations
This mimics the behavior of actual SMBus chips better.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
2008-01-27 18:14:45 +01:00
Jean Delvare b3af547e19 i2c-stub: Mention the existence of an helper script
There's a new script named i2c-stub-from-dump that can be very helpful
when working with the i2c-stub driver.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-01-27 18:14:45 +01:00
Bart Van Assche 5864ae03ca i2c: Add support for the PCF8575 chip
Signed-off-by: Bart Van Assche <bart.vanassche@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-01-27 18:14:45 +01:00
Jean Delvare 45ccc6c50d i2c: Delete an outdated piece of documentation
I'm amazed that this old piece of documentation managed to survive
until today.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2007-12-12 13:45:24 +01:00
Marcin Garski db955170d4 more UTF-8 conversions
Signed-off-by: Adrian Bunk <bunk@kernel.org>
2007-10-19 23:22:11 +02:00
David Brownell 6662cbb989 i2c: Rename the PEC functionality bit
Rename I2C_FUNC_SMBUS_HWPEC_CALC as I2C_FUNC_SMBUS_PEC, and list that
functionality as always available through the software implementation.
Update documentation accordingly (and list similar requirements).

The way it's currently packaged doesn't present the capability in a
useful way.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2007-10-13 23:56:33 +02:00
Jean Delvare 9d90c1fd9b i2c-stub: Support multiple chips
Add support for multiple chips to i2c-stub. I've changed the memory
allocation scheme from static to dynamic, so that we don't waste too
much memory.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Mark M. Hoffman <mhoffman@lightlink.com>
2007-10-13 23:56:31 +02:00
Jason Gaston e07bc679fb i2c-i801: Add support for the Intel Tolapai SMBus
Add the Intel Tolapai SMBus Controller DID.

Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2007-10-13 23:56:31 +02:00
Jean Delvare 553515e5c5 i2c/pcf8574: No arbitrary initialization
Do not initialize the PCF8574 with an arbitrary value. Users will have
to write the initial value to sysfs themselves.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Aurelien Jarno <aurelien@aurel32.net>
2007-10-13 23:56:31 +02:00
Shane Huang 60693e5a9a i2c-piix4: Fix SB700 PCI device ID
We find that SB700 and SB800 use the same SMBus device ID as SB600, which is
0x4385, instead of the already submitted 0x4395.

Besides removing the wrong SB700 device ID, add SB800 support to kernel, by
renaming the PCI_DEVICE_ID_ATI_IXP600_SMBUS into
PCI_DEVICE_ID_ATI_SBX00_SMBUS.

Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-08-31 01:42:23 -07:00
Jean Delvare 0a85e9a271 i2c-rpx: Remove
This driver has been broken forever. It depends on i2c-algo-8xx which
has never been in the mainline kernel.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2007-07-12 14:12:32 +02:00
Jean Delvare b9cdad7488 i2c: New bus driver for the TAOS evaluation modules
This is a new I2C bus driver for the TAOS evaluation modules. Developped
and tested on the TAOS TSL2550 EVM.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2007-07-12 14:12:31 +02:00
Oleg Ryjkov 7edcb9abb5 i2c-i801: Use the internal 32-byte buffer on ICH4+
Add an ability to utilize the internal SRAM buffer on ICH4
and newer host controllers to speed up execution of block operations.

I've split the code so that it is more clear which block transaction is
performed.

First of all the host controller's type is identified. isich4 is set when
we think that the controller has the internal buffer. Then, before every
block transaction, if isich4 is set, we attempt to enable the E32B bit in
SMBAUXCTL register.

Signed-off-by: Oleg Ryjkov <olegr@google.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2007-07-12 14:12:31 +02:00
Henry Su c29c22218b i2c-piix4: Add support for the ATI SB700
Add the SMBus device ID for ATI SB700.

Signed-off-by: Henry Su <Henry.su@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2007-07-12 14:12:29 +02:00
Jean Delvare 4b2643d7d9 i2c: Fix the i2c_smbus_read_i2c_block_data() prototype
Let the drivers specify how many bytes they want to read with
i2c_smbus_read_i2c_block_data(). So far, the block count was
hard-coded to I2C_SMBUS_BLOCK_MAX (32), which did not make much sense.
Many driver authors complained about this before, and I believe it's
about time to fix it. Right now, authors have to do technically stupid
things, such as individual byte reads or full-fledged I2C messaging,
to work around the problem. We do not want to encourage that.

I even found that some bus drivers (e.g. i2c-amd8111) already
implemented I2C block read the "right" way, that is, they didn't
follow the old, broken standard. The fact that it was never noticed
before just shows how little i2c_smbus_read_i2c_block_data() was used,
which isn't that surprising given how broken its prototype was so far.

There are some obvious compatiblity considerations:
* This changes the i2c_smbus_read_i2c_block_data() prototype. Users
  outside the kernel tree will notice at compilation time, and will
  have to update their code.
* User-space has access to i2c_smbus_xfer() directly using i2c-dev, so
  the changed expectations would affect tools such as i2cdump. In order
  to preserve binary compatibility, we give I2C_SMBUS_I2C_BLOCK_DATA
  a new numeric value, and define I2C_SMBUS_I2C_BLOCK_BROKEN with the
  old numeric value. When i2c-dev receives a transaction with the
  old value, it can convert it to the new format on the fly.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2007-07-12 14:12:29 +02:00
Jean Delvare 890e037509 i2c: Delete outdated x1205 driver documentation
The x1205 driver moved to the RTC subsystem and was significantly
modified since then, so just delete the outdated documentation.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Alessandro Zummo <alessandro.zummo@towertech.it>
2007-07-12 14:12:28 +02:00
John Anthony Kazos Jr be2a608bd0 documentation: convert the Documentation directory to UTF-8
Convert files within the Documentation directory to UTF-8.

Adrian Bunk:
small additional fixes

Signed-off-by: John Anthony Kazos Jr. <jakj@j-a-k-j.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
2007-05-09 08:58:19 +02:00
Jean Delvare eefcd75e72 i2c: Documentation update
Make the documentation on how to write and port i2c drivers more in
line with the current state of things:
* i2c-isa is deprecated and soon gone, so stop advertising it.
* Drop many sensors-specific references. Most of them were outdated
  anyway.
* Update the example code to reflect the recent and not-so-recent
  API and coding style preference changes.
* Simplify the example init and cleanup functions.

This should make things less complex to understand for newcomers.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2007-05-01 23:26:35 +02:00
Jean Delvare b3e820968a i2c: Make i2c_del_driver a void function
Make i2c_del_driver a void function, like all other driver removal
functions. It always returned 0 even when errors occured, and nobody
ever actually checked the return value anyway. And we cannot fail
a module removal anyway.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2007-05-01 23:26:32 +02:00
Jean Delvare ce9e0794c2 i2c: Document i2c_new_device()
Document the new i2c_new_device(), i2c_new_probed_device() and
i2c_unregister_device() functions.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2007-05-01 23:26:32 +02:00
David Brownell 4298cfc3eb i2c: i2c probe() and remove() documented
Update Documentation/i2c to match previous patches updating probe()
and remove() logic.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2007-05-01 23:26:31 +02:00
Jean Delvare f75803de6a i2c-nforce2: Add support for the MCP61 and MCP65
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans-Frieder Vogt <hfvogt@gmx.net>
2007-05-01 23:26:29 +02:00
Jonathan McDowell 55249cf750 i2c-parport: Add support for One For All remote JP1 interface
This simple patch adds support to i2c-parport for the One For All remote
JP1 parallel port interfaces which can be found detailed at:

http://www.hifi-remote.com/jp1/hardware.shtml

These allow access to the internal configuration EEPROM on various
remote controls and there are a variety of Windows tools that make use
of this hardware. I have tested this patch with the "simple" parallel
port device and a One For All URC-7562 and confirmed that the data read
using the eeprom i2c driver matches that returned by the Windows "IR"
JP1 tool.

Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2007-02-13 22:09:02 +01:00
Jean Delvare ab6a6ed271 i2c-viapro: Add support for the VIA CX700 south bridge
We do not have any documentation for the CX700, but it was reported
to work fine. Thanks to Claas Langbehn for testing.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2007-02-13 22:09:02 +01:00
David Brownell f37dd80ac2 i2c: Add driver suspend/resume/shutdown support
Driver model updates for the I2C core:

 - Add new suspend(), resume(), and shutdown() methods.  Use them in the
   standard driver model style; document them.

 - Minor doc updates to highlight zero-initialized fields in drivers, and
   the driver model accessors for "clientdata".

If any i2c drivers were previously using the old suspend/resume calls
in "struct driver", they were getting warning messages ... and will
now no longer work.  Other than that, this patch changes no behaviors;
and it lets I2C drivers use conventional PM and shutdown support.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2007-02-13 22:09:00 +01:00
Jean Delvare 099ab118b6 i2c-i801: Document the SMBus unhiding quirk
This is a frequently asked question so it deserves a paragraph in
the driver documentation.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2007-02-13 22:09:00 +01:00
Mike Frysinger 3f9a4790a3 i2c: Fix typo in SMBus Write Word Data description
Write data, don't read it.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2007-02-13 22:08:59 +01:00
Jean Delvare 4e6697fcc1 i2c-piix4: Add support for the ATI SB600
Add support for the ATI SB600 SMBus controller.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2007-02-13 22:08:59 +01:00
Jason Gaston a980a99ae5 i2c: i2c-i801 documentation update
Add the Intel ICH9/ICH8/ESB2 SMBus Controller text to
i2c-i801 documentation.

Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2006-12-10 21:21:31 +01:00
Hans-Frieder Vogt ad04d5c387 i2c: Cleanups to the i2c-nforce2 bus driver
Summary of changes:

- fixes:
   o legacy I/O region size is 64 bytes, not 8 bytes
- general cleanup:
   o removed code for the unsupported I2C block data, block data,
      proc call and block proc call transfer modes
   o removed detail warnings about unsupported modes that are
     covered in a general warning (unsupported transaction...)
     anyway
   o removed necessity of a definition of struct i2c_adapter
   o moved definition of struct i2c_algorithm, making forward
     declarations of nforce2_access and nforce2_func unnecessary
- minor changes:
   o in the description mention the nForce 5xx chipsets
   o changes my e-mail address in MODULE_AUTHOR

Theses cleanups shrink the driver binary size from 4.0 kB to 2.7 kB
on i386.

Signed-off-by: Hans-Frieder Vogt <hfvogt@gmx.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2006-12-10 21:21:29 +01:00
Jean Delvare 26f95c4ae2 i2c: Fix documentation typos
Fix typos in i2c bus drivers documentation.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2006-12-10 21:21:28 +01:00
Rudolf Marek c243353a90 i2c-viapro: Add support for the VT8237A and VT8251
i2c-viapro: Add support for the VT8237A and VT8251

Documentation update included. Compile tested.

Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-09-26 15:38:52 -07:00
Jean Delvare 7a8d29cec7 i2c-stub: Chip address as a module parameter
i2c-stub: Chip address as a module parameter

Add a mandatory chip_addr parameter to i2c-stub. This parameter
defines to which chip address the driver will respond, instead of
reponding to all addresses as before. The idea is to prevent the
users from loading i2c-stub at random and being then confused by
the results of sensors-detect or other user-space tools.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-09-26 15:38:51 -07:00
Jean Delvare 5d925fecac [PATCH] i2c: New mailing list
We have a new mailing list dedicated to linux i2c:
http://lists.lm-sensors.org/mailman/listinfo/i2c

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-07-12 15:43:07 -07:00
Jean Delvare d8db8f9856 [PATCH] i2c-i801: Remove force_addr parameter
i2c-i801: Remove force_addr parameter

Remove the force_addr module parameter. It doesn't appear to ever
have been needed, and PCI resources shouldn't be arbitrarily
changed anyway.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-22 11:10:35 -07:00
Jean Delvare 62aaa288ab [PATCH] scx200_acb: Documentation update
Documentation update for the scx200_acb driver. Hopefully this will
help future users.

References:

[lm-sensors] Support of i2c-nscacb (April, May 2005)
  http://lists.lm-sensors.org/pipermail/lm-sensors/2005-April/011756.html
  http://lists.lm-sensors.org/pipermail/lm-sensors/2005-May/012043.html

[lm-sensors] making a geode i2c slave driver (April 2006)
  http://lists.lm-sensors.org/pipermail/lm-sensors/2006-April/015998.html

Kernel bug #6445
  http://bugzilla.kernel.org/show_bug.cgi?id=6445

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-22 11:10:35 -07:00
Peter Korsgaard 18f98b1e31 [PATCH] i2c: New bus driver for the OpenCores I2C controller
The following patch adds support for the OpenCores I2C controller IP
core (See http://www.opencores.org/projects.cgi/web/i2c/overview).

Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-22 11:10:33 -07:00
Jean Delvare 5c7ae65899 [PATCH] I2C: i2c-nforce2: Add support for the nForce4 MCP51 and MCP55
Add support for the new nForce4 MCP51 (also known as nForce 410 or
430) and nForce4 MCP55 to the i2c-nforce2 driver. Some code changes
were required because the base I/O address registers have changed in
these versions. Standard BARs are now being used, while the original
nForce2 chips used non-standard ones.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-22 11:10:33 -07:00
Jean Delvare f9ba6c04ef [PATCH] I2C: i2c-piix4: Document the IBM problem more clearly
Properly document on which systems the i2c-piix4 SMBus driver will
refuse to load. Hopefully this will make it clearer for users, which
were often wondering why their destop or server systems were detected
as laptops.

Closes bug #6429.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-22 11:10:32 -07:00
Jean Delvare 7aadb8f943 [PATCH] I2C: i2c-piix4: Fix typo in documentation
Fix i2c-piix4 documentation typo.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-22 11:10:32 -07:00
Rudolf Marek 54aaa1ca10 [PATCH] I2C: i2c-piix4: Remove the fix_hstcfg parameter
This patch removes the fix_hstcfg option from the driver and related
SMBus Interrupt Select register magic because now we know what are
valid values for this register. This patch updates the documentation
and adds new IRQ mode check so we are sure not to miss any new
"unusual" value.

The PCI quirk for users of fix_hstcfg was not developed because the
chipset lacks of subsystem ID registers and DMI is stated "To be
filled". Impact to existing systems is minimal because the problem
showed up on motherboards like 10 years back. On the other hand users
of newer Serverworks and HT1000 systems won't be misleaded by the
message suggesting to try the fix_hstcfg any more.

Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-22 11:10:32 -07:00
Rudolf Marek 02e0c5d5c2 [PATCH] i2c-piix4: Add ATI IXP200/300/400 support
This patch adds the ATI IXP southbridges support to i2c-piix4,
as it turned out those chips are compatible with it.

Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-22 11:10:32 -07:00
Mark M. Hoffman e97b81ddbb [PATCH] i2c-parport: Make type parameter mandatory
This patch forces the user to specify what type of adapter is present when
loading i2c-parport or i2c-parport-light.  If none is specified, the driver
init simply fails - instead of assuming adapter type 0.

This alleviates the sometimes lengthy boot time delays which can be caused
by accidentally building one of these into a kernel along with several i2c
slave drivers that have lengthy probe routines (e.g. hwmon drivers).

Kconfig and documentation updated accordingly.

Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-04-14 11:18:34 -07:00
Martin Devera 5f7ea3c58c [PATCH] I2C: i2c-piix4: Add Broadcom HT-1000 support
Add Broadcom HT-1000 south bridge's PCI ID to i2c-piix driver. Note
that at least on Supermicro H8SSL it uses non-standard SMBHSTCFG = 3
and standard values like 0 or 9 causes hangup.

Signed-off-by: Martin Devera <devik@cdi.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-03-23 14:21:55 -08:00
Ben Gardner a417bbd33b [PATCH] i2c: scx200_acb minimal documentation update
scx200_acb: Minimal documentation update

Signed-off-by: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-03-23 14:21:50 -08:00
Rudolf Marek 806ba64090 [PATCH] i2c: Rename i2c-sis96x documentation file
This patch just renames the documentation file to correct file name.
i2c-sis69x -> i2c-sis96x.

Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-02-06 12:02:14 -08:00
Jean Delvare 7c72ccf09b [PATCH] i2c: i2c-nforce2 add nforce4 MCP-04 device ID
One more supported PCI ID for the i2c-nforce2 driver.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-05 22:16:27 -08:00
Jean Delvare fb687d73fa [PATCH] i2c: update i2c_driver.command documentation
Document i2c_driver.command as being deprecated, and don't suggest an
empty implementation of this callback as it doesn't make any sense.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-05 22:16:26 -08:00
Jean Delvare d82c0bf88f [PATCH] i2c: Documentation update
Update the i2c documentation to reflect the recent change to
i2c_add_driver.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-05 22:16:25 -08:00
Jean Delvare d45d204f0c [PATCH] i2c: Drop i2c_driver.{owner,name}, 11 of 11
Document the drop of the owner and name fields of the i2c_driver
structure.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
CC: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-05 22:16:24 -08:00
Jean Delvare 92b4294612 [PATCH] i2c: Chip driver porting guide update
Update Documentation/i2c/porting-clients. Many recent changes to the i2c
and hwmon subsystems were never reported there.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-05 22:16:22 -08:00
Jean Delvare cf02df7702 [PATCH] i2c: Rework client usage count, 3 of 3
Do not limit the usage count of i2c clients to 1. In other words,
change the client usage count behavior from the old I2C_CLIENT_ALLOW_USE
to the old I2C_CLIENT_ALLOW_MULTIPLE_USE. The rationale is that no
driver actually needs the limiting behavior, and the unlimiting
behavior is slightly easier to implement.

Update the documentation to reflect this change.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-05 22:16:22 -08:00
Jean Delvare 8a9947552d [PATCH] i2c: Drop i2c_driver.flags, 2 of 3
Just about every i2c chip driver sets the I2C_DF_NOTIFY flag, so we
can simply make it the default and drop the flag. If any driver really
doesn't want to be notified when i2c adapters are added, that driver
can simply omit to set .attach_adapter. This approach is also more
robust as it prevents accidental NULL pointer dereferences.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-05 22:16:21 -08:00
Peter Korsgaard 1d26f455eb [PATCH] i2c: Add support for Barco LPT->DVI to i2c-parport
The following patch adds support for the Barco LPT->DVI I2C adapter to
the i2c-parport driver.

Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-05 22:16:21 -08:00
Jean Delvare 8750197f0e [PATCH] i2c-viapro: Some adjustments
The big i2c-viapro SMBus driver update which went into 2.6.14-git1
introduced a few minor issues. Nothing critical, but I would like a
few adjustments to be merged in to fix the following problems:

* VIA should not be spelled Via.
* Frodo Looijaard and Philip Edelbrock did not write the i2c-viapro
  driver.
* When debugging is disabled, half of messages would be logged.
* Drop an unneeded masking.
* Some port reads can be avoided now that the transaction size is
  passed as a parameter to vt596_transaction().
* SMBus Receive Byte transactions are used for probing too (for
  EEPROMs), so hide errors on these too.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-11-07 21:46:38 -08:00
Jean Delvare a852daa00a [PATCH] i2c: writing-client doc update complement
My latest update to the writing-clients i2c documentation file was
incomplete, here's the complement.

Large parts of this file are still way out-of-date, but at least now
the memory allocation and freeing instructions are consistent.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-11-07 21:46:37 -08:00
Jeff Garzik d61780c0d3 [PATCH] remove some more check_region stuff
Removed some more references to check_region().

I checked these changes into the 'checkreg' branch of
rsync://rsync.kernel.org/pub/scm/linux/kernel/git/jgarzik/misc-2.6.git

The only valid references remaining are in:
drivers/scsi/advansys.c
drivers/scsi/BusLogic.c
drivers/cdrom/sbpcd.c
sound/oss/pss.c

  Remove last vestiges of ide_check_region()
  drivers/char/specialix: trim trailing whitespace
  drivers/char/specialix: eliminate use of check_region()
  Remove outdated and unused references to check_region()
  [sound oss] remove check_region() usage from cs4232, wavfront
  [netdrvr eepro] trim trailing whitespace
  [netdrvr eepro] remove check_region() usage

Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-10-30 17:37:18 -08:00
Jean Delvare 142078f6f0 [PATCH] i2c: i2c-i810 documentation update
Update the documented list of devices supported by the i2c-i810
driver.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-10-28 14:02:13 -07:00
Jean Delvare 2445eb62e9 [PATCH] i2c: Documentation update
Update the i2c documentation: kzalloc should be used instead of
kmalloc.

I also fixed a couple other things nearby in writing-clients, as several
past changes had never been reported there.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-10-28 14:02:12 -07:00
Alessandro Zummo 4d4e5ce864 [PATCH] i2c: New Xicor X1205 RTC driver
New driver for the Xicor X1205 RTC chip.

Signed-off-by: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-10-28 14:02:12 -07:00
Jean Delvare 7865e24935 [PATCH] i2c: Documentation fixes
i2c documentation fixes.

>From Hideki Iwamoto:
* i2c_smbus_read_i2c_block_data is not deleted in 2.6.10. It still
  exists.
* The name which can be set to i2c_driver is up to 31 characters.

>From Jean Delvare:
* Reword the paragraph about i2c_driver.name, to reflect the "new"
  naming policy.
* Delete the out-of-date note about now gone inc_use and dec_use
  fields.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-10-28 14:02:09 -07:00
Jean Delvare aaf7f14776 [PATCH] i2c-viapro: Update supported devices list
Make it clearer which chips are supported by the i2c-viapro driver,
and which support I2C block transactions.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 Documentation/i2c/busses/i2c-viapro |   12 ++++++------
 drivers/i2c/busses/i2c-viapro.c     |   22 +++++++++++++---------
 2 files changed, 19 insertions(+), 15 deletions(-)
2005-10-28 14:02:08 -07:00
Jean Delvare f118301416 [PATCH] i2c-viapro: Implement I2C Block transactions
Implement the I2C block transactions on VIA chips which support them:
VT82C686B, VT8233, VT8233A, VT8235 and VT8237R. This speeds up EEPROM
accesses by a factor 10 or so.

I would like to thank Antonino A. Daplas, Hinko Kocevar, Salah Coronya
and Andreas Henriksson for their help in testing this new feature.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 Documentation/i2c/busses/i2c-viapro |    7 +++++-
 drivers/i2c/busses/i2c-viapro.c     |   39 +++++++++++++++++++++++++++++++++---
 2 files changed, 42 insertions(+), 4 deletions(-)
2005-10-28 14:02:08 -07:00
Jean Delvare 5f49ef8e8c [PATCH] i2c-viapro: Coding style fixes
Before I go on cleaning up and improving the i2c-viapro driver, let's
fix all the coding style issues: mostly trailing white space, and
spaces used where tabs should be.

Signed-off-by: Jean Delvare <khali@linux-fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 Documentation/i2c/busses/i2c-viapro |   12 ++---
 drivers/i2c/busses/i2c-viapro.c     |   76 ++++++++++++++++++------------------
 2 files changed, 43 insertions(+), 45 deletions(-)
2005-10-28 14:02:07 -07:00
Hideki Iwamoto d057c96cab [PATCH] i2c: Fix I2C_FUNC_PROTOCOL_MANGLING documentation
Fix the description of I2C_FUNC_PROTOCOL_MANGLING.

From: Hideki Iwamoto <h-iwamoto@kit.hi-ho.ne.jp>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 Documentation/i2c/functionality |    7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)
2005-10-28 14:02:07 -07:00
Jean Delvare 4c9337da37 [PATCH] I2C: Centralize 24RF08 corruption prevention
The 24RF08 corruption would better be prevented at i2c-core level than
at chip driver level, for several reasons:
* The second quick write should happen as soon as possible after the
  first one, so as to limit the risk that another command is issued on
  the bus inbetween, causing the corruption.
* As a matter of fact, the protection code at driver level was reworked
  at least three times already, which proves how hard it is to get it
  right there, while it's straightforward at i2c-core level.
* It's easy to add a new driver that would need the protection, and
  forget to add it. This did happen already.
* As additional probing addresses can be passed to most i2c chip drivers
  as module parameters, virtually every i2c chip driver would need the
  protection if we want to be really safe.
* Why duplicate code when we can easily avoid it?

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-09-05 09:14:25 -07:00