Replace the V4L2_IDENT_* usage with tveeprom-specific defines. This header
is deprecated, so those defines shouldn't be used anymore.
The em28xx driver is the only one that uses the tveeprom audio_processor
field, so that has been updated to use the new tveeprom AUDPROC define.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
VIDIOC_DBG_G_CHIP_IDENT has been replaced by VIDIOC_DBG_G_CHIP_INFO. Remove
g_chip_ident support from bridge drivers since it is no longer needed.
This patch takes care of all the trivial cases.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hardware is the same as MaxMedia UB425-TC but ships with a different
remote.
Signed-off-by: Jakob Haufe <sur5r@sur5r.net>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
X-Patchwork-Delegate: mchehab@redhat.com
In addition to commit 72cc9ba3 "em28xx: ignore isoc DVB USB endpoints with
wMaxPacketSize = 0 bytes for all alt settings" we should not save the endpoint
number of the isoc DVB endpoint before it has been validated.
While the current code works fine, dev->dvb_ep_isoc != 0 could be interpreted
as indicator that the device provides DVB support.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
commit 61ff5d69 "em28xx: improve em2710/em2820 distinction" missed the
le16_to_cpu conversion of the USB vendor ID.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit cd634f1 ("[media] v4l2: put VIDIOC_DBG_G_CHIP_NAME under
ADV_DEBUG") missed the initializer of radio_ioctl_ops:
drivers/media/usb/em28xx/em28xx-video.c:1830:2: error: unknown field 'vidioc_g_chip_info' specified in initializer
drivers/media/usb/em28xx/em28xx-video.c:1830:26: error: 'vidioc_g_chip_info' undeclared here (not in a function)
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Chip id 18 is used by the em2710 and em2820.
The current code assumes that if the device is a camera, the chip is an em2710
and an em2820 otherwise.
But it turned out that the em2820 is also used in camera devices.
"Silvercrest 1.3 MPix" webcams for example are available with both chips.
Fortunately both variants are using different generic USD IDs which give us a
hint about the used chip.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The snapshot button support is currently broken, because module em28xx-rc is
loaded only if the device has remote control support.
Fix it by also loading this module if the device has a snapshot button.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
dvb->adapter.priv should also be set to the i2c bus since that's what
em28xx_tuner_callback expects.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ioctl will be extended to return more information than just the name.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Only enable this ioctl if the VIDEO_ADV_DEBUG config option is set. This
prevents abuse from both userspace and kernelspace (some bridge drivers
abuse DBG_G_CHIP_IDENT, lets prevent that from happening again with this
ioctl).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
em28xx: fix typo in scale_to_size().
The second hscale should be vscale. This bug caused xawtv to fail because it
cannot find a workable image size.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This sensor is used by the "SpeedLink Vicious And Devine Laplace webcam" and
others. It supports resolutions up to 1600x1200 (at 7-8 fps), but for
resolutions higher than 640x480, further driver changes will be necessary,
such as sensor output resolution switching (including further configuration
changes), bridge xclk adjustment and disabling of 16 bit (12 bit) output formats
at high resolutions. Image quality should also needs to be improved.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Windows driver also probes at least two further i2c addresses (0x22 >> 1
and 0x66 >> 1). I've got some hints that they are very likely used by Samsung
and Kodak sensors, which are known to be used in Empia devices, too.
We havn't seen any devices using these sensors yet and don't know how to probe
them properly, so leave a comment.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
OmniVision sensors are used as well in Empiatech based cameras such as the
"SpeedLink Vicious And Devine Laplace" webcam (EM2765 + Omnivision OV2640).
With this patch applied, OminiVision sensors with 8 bit address and register
width are detected (recent models have a 16 bit address width and use different
client addresses).
The most commonly used sensors (including the ones listed by Empiatech) are
detected properly, although there is no support for them yet.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Other sensors like the ones from OmniVision need a different probing procedure,
so it makes sense have separate functions for each manufacturer/sensor type.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add further Micron chip IDs to be able to identify all Micron sensors listed
by Empiatech.
Also probe the two alternate i2c addresses used by Micron sensors with 8 bit
address and 16 bit register width.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
em28xx-cards.c is very large and the sensor/camera related code is growing,
so move this code to a separate source code file em28xx-camera.c.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that the board hints and the sensor initialization/configuration have been
separated, em28xx_detect_sensor() is the better name for this function.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sensor detection and initialization/configuration are currently mixed together.
This works as long as all devices with a particular sensor are working with the
same board configuration. In the long run, this will be not sufficient, so
separate these both steps to make the code more flexible and future proof.
This also makes the code more consistent, because the initialization of the
MT9V011 sensor subdevice is already separated.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current board hint code is mixed together with the sensor detection and
initialization code. It actually selects a board depending on the detected
sensor type only, with the result that 3 of the 6 webcam boards are currently
dead.
Separate it and move it to em28xx_hint_board() which already contains the board
hints for analog capturing+TV and DVB devices.
This way, we have all board hints at a common place which makes it easier
to extend the code and reduces the risk of regressions.
It also makes it possible again to use the boards EM2750_BOARD_DLCW_130,
EM2820_BOARD_VIDEOLOGY_20K14XUSB and EM2860_BOARD_NETGMBH_CAM (using the module
parameter "card").
NOTE: the current board hint logic for webcams is preserved. Not more not less.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some devices without DVB support (such as the "Terratec Grabby" and
"Easycap DC-60") provide isochronous DVB USB endpoints with wMaxPacketSize set
to 0 bytes for all alt settings.
Ignore these endpoints and avoid registering a DVB device node and loading the
DVB driver extension.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Tested-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Windows driver writes the output resolution to registers 0x34 (width / 16)
and 0x35 (height / 16) always.
We don't know yet what these registers are used for.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Streaming doesn't work with the EM2765 if bit 5 of the output format register
0x27 is set.
It's actually not clear if really has to be set for the other chips, but for
now let's keep it to avoid regressions and add a comment to the code.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The em25xx/em276x/em277x/em278x frame data format is different to the one used
by the em2710/em2750/em28xx chips.
With the recent cleanups and reorganization of the frame data processing code it
can be easily extended to support these devices.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This chip can be found in the SpeedLink VAD Laplace webcam (1ae7:9003 and 1ae7:9004).
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The webcam "SpeedLink VAD Laplace" (em2765 + ov2640) uses a special algorithm
for i2c communication with the sensor, which is connected to a second i2c bus.
We don't know yet how to find out which devices support/use it.
It's very likely used by all em25xx and em276x+ bridges.
Tests with other em28xx chips (em2820, em2882/em2883) show, that this
algorithm always succeeds there although no slave device is connected.
The algorithm likely also works for real i2c client devices (OV2640 uses SCCB),
because the Windows driver seems to use it for probing Samsung and Kodak
sensors.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for vidioc_g_chip_name, allowing AC97 to be implemented as a
second chip on the bridge with the name "ac97". v4l2-dbg can just match the
name with that string in order to detect a ac97-compliant set of registers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ioctl is defined as IOW, so pass the argument as const.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ioctl is defined as IOW, so pass the argument by value instead of by
reference. I could have chosen to add const instead, but this is 1) easier
to handle in drivers and 2) consistent with the s_std subdev operation.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ioctl is defined as IOW, so pass the argument as const.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ioctl is defined as IOW, so pass the argument as const.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit aab3125c43 broke em28xx. I traced
this eventually to the change in what algo_data points to. This pointer
is also passed to em28xx_tuner_callback() through several hidden tuner
layers (yuck!) and that callback was not updated.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There's currently a bug on em28xx-i2c that makes it write the
wrong values to register 06, that controlls the I2C bus speed
and bus.
Fix it to change only the I2C bus flag.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is an hybrid board. However, for analog, it requires
a new driver for saa7136. So, for now, let's just add
support for Digital TV.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It turned out that some devices return less bytes then requested via i2c when
ALL of the following 3 conditions are met:
- i2c bus B is used
- there was no attempt to write to the specified slave address before
- no device present at the specified slave address
With the current code, this triggers an -EIO error and prints a message to the
system log.
Because it can happen very often during device probing, it is better to ignore
this error and bail out silently after the follwing i2c transaction success
check with -ENODEV.
[mchehab@redhat.com: a small CodingStyle fix]
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The em28xx driver obtains the timestamps using function v4l2_get_timestamp(),
which produces a montonic timestamp.
Fixes the warnings appearing in the system log since commit 6aa69f99
"[media] vb2: Add support for non monotonic timestamps"
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Register both buses 0 and 1 via I2C API. For now, bus 0 is used
only by eeprom on all known devices. Later patches will be needed
if this changes in the future.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Prepare to register a separate bus for the second bus.
For now, just add a new field. A latter patch will add the
bits to make it work.
This patch was generated by this script:
perl -e 'while (<>) { if (s/EM2874_I2C_SECONDARY_BUS_SELECT.*\n//) {
printf "\t\t.def_i2c_bus = 1,\n"; $found = 1; print $_ } else { if ($found) { s/^\s+// }; $found = 0; print $_; } }' \
drivers/media/usb/em28xx/em28xx-cards.c >a && mv a drivers/media/usb/em28xx/em28xx-cards.c
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Newer em28xx devices have 2 buses. Change the logic to allow
using both buses.
This patch was generated by this small script:
for i in drivers/media/usb/em28xx/*.c; do
sed 's,->i2c_adap,->i2c_adap[dev->def_i2c_bus],g;s,->i2c_client,->i2c_client[dev->def_i2c_bus],'
done
Of course, em28xx.h needed manual edit.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Putting em28xx in suspend mode when a feed stops is just plain
wrong. Every time a new PES filter is changed, the DVB demux
code will stop the current feed, and then start a new one.
If are there any code that switches off the frontend, via
some GPIO setting, this would make the DVB fail.
This condition was actually trigged with one device, during
DVB scan, as, during scan, it is common that userspace apps
to change the filter several times, in order to get all
tables.
Also, this is not needed at all, since the em28xx code already
hooks into ops.ts_bus_ctrl(). This warrants that em28xx can
check there if DVB frontend is in usage or not. The code there
already puts the device on suspend mode, if the DVB frontend
is not used (closed).
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The new eeproms with 16 address width still have the the device config dataset
(the content of the old 8 bit eeproms) embedded.
Hauppauge also continues to include the tveeprom data structure inside this
dataset in their devices.
The start address of the dataset depends on the start address of the microcode
and a variable additional offset.
It should be mentioned that Camera devices seem to use a different dataset type,
which is not yet supported.
Tested with devices "Hauppauge HVR-930C". I've also checked the USB-log from the
"MSI Digivox ATSC" and it works the same way.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We currently reserve an array of 256 bytes for the eeprom content in the device
struct. For eeproms with 16 bit address width it might even be necessary to
increase the buffer size further.
Having such a big chunk of memory reserved even if the device has no eeprom and
keeping it after it has already been processed seems to be a waste of memory.
Change the code to allocate + free the eeprom memory dynamically.
This also makes it possible to handle different dataset sizes depending on what
is stored/found in the eeprom.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a helper function for reading data blocks from i2c devices with 8 or 16 bit
address width and 8 bit register width.
This allows us to reduce the size of new code added by the following patches.
Works only for devices with activated register auto incrementation.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Newer devices (em2874, em2884, em28174, em25xx, em27[6,7,8]x) use eeproms with
16 bit instead of 8 bit address width.
The used eeprom type depends on the chip type, which makes sure eeproms can't
be damaged.
This patch adds basic support for 16 bit eeproms only, which includes
- reading the content
- calculating the eeprom hash
- displaying the content
The eeprom content uses a different format, for which support will be added with
subsequent patches.
Tested with the "Hauppauge HVR-930C" and the "Speedlink VAD Laplace webcam"
(with additional experimental patches).
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The data is stored as little endian in the eeprom.
Hence the correct data types should be used and the data should be converted
to the machine endianess before using it.
The eeprom id (key) also isn't a 32 bit value but 4 separate bytes instead.
[mchehab@redhat.com: Fix CodingStyle]
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the eeprom key isn't valid, either a different (currently unknown) format
is used or the eeprom is corrupted.
In both cases it doesn't make sense to interpret the data.
Also print an error message.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current code uses only a single debug level and all debug messages are
printed for i2c_debug >= 2 only. So debug level 1 is actually the same as
level 0, which is odd.
Users expect debugging messages to become enabled for anything else than
debug level 0.
Fix it and simplify the code a bit by printing the debug messages also at debug
level 1;
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reduces the number of characters/lines, unifies the code and improves readability.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is only a single place where the dprintk2 macro is used, so get rid of it.
[mchehab@redhat.com: fix checkpathc.pl complain:
ERROR: space prohibited before that close parenthesis ')']
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The em28xx driver has changed much, especially since kernel 3.8.
So it's time to bump the driver version.
Changes since kernel 3.8:
- converted the driver to videobuf2
- converted the driver to the v4l2-ctrl framework
- added USB bulk transfer support
- use USB bulk transfers by default for webcams (allows streaming from multiple devices at the same time)
- added image quality bridge controls: contrast, brightness, saturation, blue balance, red balance, sharpness
- removed dependency from module ir-kbd-i2c
- cleaned up the frame data processing code
- removed some unused/obsolete code
- made remote controls of devices with external (i2c) receiver/decoder work again
- fixed audio over USB for device "Terratec Cinergy 250"
- several v4l2 compliance fixes and improvements (including fixes for ioctls enabling/disabling)
- lots of further bug fixes and code improvements
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the image quality bridge controls contrast, brightness, saturation,
blue balance, red balance and sharpness.
These controls are enabled only if no subdevice provides them.
Tested with the following devices:
"Terratec Cinergy 200 USB"
"Hauppauge HVR-900"
"SilverCrest 1.3MPix webcam"
"Hauppauge WinTV USB2"
"Speedlink VAD Laplace webcam"
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The image quality default values will be used in at least two different places
and by using #defines we make sure that they are always consistent.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Output resolutions <=20% of the input resolution exceed the capabilities of the
scaler.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The maximum supported scaling value for registers 0x30+0x31 (horizontal scaling)
and 0x32+0x33 (vertical scaling) is 0x3fff, which corresponds to 20% of the
input frame size.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Avoids registering a VBI device and streaming in VBI-mode if the device is a
camera.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
VIDIOC_DBG_G_CHIP_IDENT is a "normal" and not an "advanced" debug functionality.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2_device_disconnect() is called when the device is disconnected, so that the
v4l2-core rejects all ioctl calls.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The tuner type is set by the v4l2-core based on the device type.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
vidioc_s_fmt_vbi_cap() is a 100% duplicate of vidioc_g_fmt_vbi_cap() and
therefore can be removed.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The em28xx driver doesn't support the VIDIOC_G_CROP and VIDIOC_S_CROP ioctls,
so VIDIOC_CROPCAP is useless and has the potential to confuse applications,
because it can be interpreted as indicator for cropping support.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the current code V4L2_BUF_TYPE_VIDEO_CAPTURE is accepted only, but for VBI
devices only buffer type V4L2_BUF_TYPE_VBI_CAPTURE is used/valid.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
VIDIOC_S_PARM doesn't make sense for VBI device nodes, because we don't support
selecting the number of read buffers to use.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of checking the device type and returning -ENOTTY inside the ioctl
function, use v4l2_disable_ioctl() to disable the ioctl VIDIOC_S_PARM if the
device is not a camera.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of checking the device type and returning -EINVAL inside the ioctl
functions, use v4l2_disable_ioctl() to disable the ioctls VIDIOC_G_AUDIO and
VIDIOC_S_AUDIO if the device doesn't support audio.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Disable the ioctls VIDIOC_G_TUNER, VIDIOC_S_TUNER, VIDIOC_G_FREQUENCY and
VIDIOC_S_FREQUENCY for video and VBI devices without tuner.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of checking the device type and returning -ENOTTY inside the ioctl
functions, use v4l2_disable_ioctl() to disable the ioctls VIDIOC_QUERYSTD,
VIDIOC_G_STD and VIDIOC_S_STD if the device is a camera.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Seems to work just the same as older revisions.
Signed-off-by: Roland Scheidegger <rscheidegger_lists@hispeed.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the conversion to videobuf2, some unnecessary calls of
em28xx_set_alternate() have been removed. It is now called at analog streaming
start only.
This has unveiled a bug that causes USB bulk transfers to fail with all urbs
having status -EVOERFLOW.
The reason is, that for bulk transfers usb_set_interface() needs to be called
even if the previous alt setting was the same (side note: bulk transfers seem
to work only with alt=0).
While it seems to be NOT necessary for isoc transfers, it's reasonable to just
call usb_set_interface() unconditionally in em28xx_set_alternate().
Also add a comment that explains the issue to prevent regressions in the future.
Cc: stable@vger.kernel.org # for 3.8
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bytesperline calculation was incorrect: it used the old width instead of
the provided width. Fixed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- move the bit shifting of width+height values inside the function
- fix the debug message format and output values
- add comment about the size limit (e.g. EM277x supports >2MPix)
- make void, because error checking is incomplete and we never check the
returned value (we would continue anyway)
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove em28xx_i2c_ir_work() and check the device type in the common callback
function em28xx_ir_work() instead. Simplifies em28xx_ir_start().
Reduces the code size with a minor performance drawback.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Set up the i2c_client locally in em28xx_i2c_ir_handle_key().
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We already have the key polling functions and the polling infrastructure in
em28xx-input, so we can easily get rid of the dependency on module ir-kbd-i2c.
For maximum safety, do not touch the key reporting mechanism for those devices.
Code size could be improved further but would have minor peformance impacts.
Tested with device "Terratec Cinergy 200 USB" (EM2800_BOARD_TERRATEC_CINERGY_200)
[mchehab@redhat.com: Fix two checkpatch.pl warnings:
ERROR: "foo * bar" should be "foo *bar" (line 465)
WARNING: kfree(NULL) is safe this check is probably not required (line 725)]
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We don't report any key/scan codes or errors inside the key polling functions
for internal IR RC devices, just in the key handling fucntions.
Do the same for external devices.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Field 'old' of struct IR_i2c is used nowhere in module ir-kbd-i2c.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remy Blank reported that audio over USB can be made working for the television
input if .amux is changed from EM28XX_AMUX_LINE_IN to EM28XX_AMUX_VIDEO.
An examination of his devices shows, that it is indeed supplied with an EM202
AC97 audio IC. We also use this setting for the Cinergy 200.
Remy Blank also provided the original version of this patch (many thanks !).
Fixes bug 14126 (see bug report for further device details).
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Remy Blank <remy.blank@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that it uses videobuf2, em28xx can support DMABUF.
Tested with an HVR-950 on analog mode and a 2gen i5core machine
with an i915 graphics adapter.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
That fixes the following warning:
drivers/media/usb/em28xx/em28xx-video.c:611:5: warning: no previous prototype for 'em28xx_stop_streaming' [-Wmissing-prototypes]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
EEPROMs are currently read in blocks of 16 bytes, but the em2800 is limited
to 4 bytes per read. All other chip variants support reading of max. 64 bytes
at once (according to the em258x datasheet; also verified with em2710, em2882,
and em28174).
Since em2800_i2c_recv_bytes() has been fixed to return with -EOPNOTSUPP when
more than 4 bytes are requested, EEPROM reading with this chip is broken.
It was actually broken before that change, too, it just didn't throw an error
because the i2c adapter silently returned trash data (for all reads >1 byte !).
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- do not pass USB specific error codes to userspace/i2c-subsystem
- unify the returned error codes and make them compliant with
the i2c subsystem spec
- check number of actually transferred bytes (via USB) everywehere
- fix/improve debug messages
- improve code comments
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I2C_FUNC_SMBUS_EMUL includes flag I2C_FUNC_SMBUS_WRITE_BLOCK_DATA which signals
that up to 31 data bytes can be written to the ic2 client.
But the EM2800 supports only i2c messages with max. 4 data bytes.
I2C_FUNC_IC2 should be set if a master_xfer function pointer is provided in
struct i2c_algorithm.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Function em2800_i2c_recv_bytes() has 2 severe bugs:
1) It does not wait for the i2c read to complete before reading the received message content from the bridge registers.
2) Reading more than 1 byte doesn't work
The former can result in data corruption, the latter always does.
The rewritten code also superseds the content of function
em2800_i2c_check_for_device().
Tested with device "Terratec Cinergy 200 USB".
[mchehab@redhat.com: Fix CodingStyle issues]
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The em2800 can transfer up to 4 bytes per i2c message.
All other em25xx/em27xx/28xx chips can transfer at least 64 bytes per message.
I2C adapters should never split messages transferred via the I2C subsystem
into multiple message transfers, because the result will almost always NOT be
the same as when the whole data is transferred to the I2C client in a single
message.
If the message size exceeds the capabilities of the I2C adapter, -EOPNOTSUPP
should be returned.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The get_key functions are independent from the selected protocol, so assign
them once only at device initialization.
[mchehab@redhat.com: fix a merge conflict]
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The main purpose of this patch is to move the call of em28xx_release_resources()
after the call of em28xx_close_extension().
This is necessary, because some resources might be needed/used by the extensions
fini() functions when they get closed.
Also mark the device as disconnected earlier in this function and unify the
em28xx_uninit_usb_xfer() calls for analog and digital mode.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
DEV_INITIALIZED of enum em28xx_dev_state state is used nowhere and there is no
need for DEV_MISCONFIGURED, so remove this enum and use a boolean field
'disconnected' in the device struct instead.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch converts the em28xx driver over to videobuf2. It is
likely that em28xx_fh can go away entirely, but that will come in
a separate patch.
[mchehab@redhat.com: fix a non-trivial merge conflict with some VBI
patches; CodingStyle fixes]
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The sliced VBI support in the tvp5150 is completely broken. And there is no
support for the saa7115 sliced VBI implementation in the em28xx driver. So
we remove the sliced VBI support completely.
It should be possible to get it to work with the tvp5150, but that will
require someone to really dig into that driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When in webcam mode the STD API shouldn't be implemented.
When changing the standard the resolution wasn't updated, and there was no
check against streaming-in-progress.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
g/s_parm should fill in readbuffers.
For non-webcams s_parm should return -ENOTTY instead of -EINVAL.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2-compliance found problems with frequency clamping that wasn't
reported correctly and missing tuner index checks.
Also removed unnecessary tuner type checks (these are now done by the
v4l2 core).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Radio devices should not implement those ioctls.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ir-i2c-kbd already adds I2C IR before the name. The way it is,
the devices are named as:
"i2c IR (i2c IR (EM2840 Hauppaug"
With is ugly and incorrect. After this patch, it is now properly
displayed as:
"i2c IR (WinTV USB2)"
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the device has an I2C IR, em28xx-rc should be loaded by default,
except if the user explicitly requested to not load, via modprobe
option.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The em28xx-input is used by 3 different types of input devices:
- devices with buttons (like cameras and grabber devices);
- devices with I2C remotes;
- em2860 or latter chips with RC support embedded.
When the device has an I2C remote, all it needs to do is to call
the proper I2C driver (ir-i2c-kbd), passing the proper data to
it, and just leave the code.
Also, button devices have its own init code that doesn't depend on
having an IR or not (as a general rule, they don't have).
So, move its init code to fix bugs introduced by earlier patches
that prevent them to work.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since we have now 3 modes (auto/isoc/bulk), usb_xfer_mode is more suitable than prefer_bulk.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Using bulk mode allows more than one webcam, as the maximum fps
is low at 640x480 resolution. So, prefer it, if the device is
a webcam.
Tested with Silvercrest 1.3 Mpixel webcam (em2710) on both bulk and isoc
modes.
Tested analog with HVR-950 model 65201/A1C0 (em2883), where only ISOC
endpoints are available for both DVB and Analog.
Tested on Hauppauge WinTV USB 2 (em2840) on both bulk and isoc modes.
It should be noticed that enabling bulk mode by default with TV boards
is a bad idea; what happens is that, while with ISOC the USB logic will
prevent the concurrent usage of two devices that spends more than 100%
of the USB2 traffic, it doesn't care with bulk transfers.
On my tests, I started two streams, one with a WinTV at 640x480x30fps
and the other one with a Silvercrest webcam at 640x480, on a lower fps)
both on bulk mode. One of the streams always silently failed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In order to make easier to analize the logs when multiple devices
are plugged, change the device name accordingly with the chip
version.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As both bulk and isoc modes can be available, display what it
was found for both DVB and analog.
While here, also displays if audio is provided via USB Audio
Class or via vendor's extension.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As the bulk mode is set at device's probe, it is not possible
to change it later. So, change the parameter to be read only
after modprobing.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The code in em28xx_vbi_copy can be simplified a lot.
Also rename some variables to something more meaningful and fix+add the
function descriptions.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
em28xx_urb_data_copy() actually consists of two parts:
USB urb processing (checks, data extraction) and frame data packet processing.
Move the latter to a separate function and call it from em28xx_urb_data_copy()
for each data packet.
The em25xx, em2760, em2765 (and likely em277x) chip variants are using a
different frame data format, for which support will be added later with
another function.
This reduces the size of em28xx_urb_data_copy() and makes the code much more
readable. While we're at it, clean up the code a bit (rename some variables to
something more meaningful, improve some comments etc.)
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reduce code duplication by moving the duplicate code for dev->capture_type=0
(vbi start) and dev->capture_type=2 (video start) to a function.
The same function will also be called by the (not yet existing) em25xx frame
data processing code.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the current code em28xx_urb_data_copy() caches the pointer to the vmalloc
memory in videobuf locally.
The alternative would be to call videobuf_to_vmalloc() for each processed USB
data packet (isoc USB transfers => 64 times per URB) in the em28xx_copy_*()
functions.
With the next commits, the data processing code will be split into functions
for serveral reasons:
- em28xx_urb_data_copy() is generally way to long, making it less readable
- there is code duplication between VBI and video data processing
- support for em25xx data processing (uses a different header and frame
end signaling mechanism) will be added
This would require extensive usage of pointer-pointers, which usually makes the
code less readable and prone to bugs.
The better solution is to cache the pointer in struct em28xx_buffer.
This also improves consistency, because we already track the buffer fill count there.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When a new frame header is detected in em28xx_urb_data_copy() and the data
packet contains both, VBI data and video data, the prevoius VBI buffer doesn't
get finished and is overwritten with the new VBI data.
This bug is not triggered with isochronous USB transfers, because the data
packetes are much smaller than the VBI data size.
But when using USB bulk transfers, the whole data of an URB is treated as
single packet, which is usually much larger then the VBI data size.
Refactor the VBI data processing code to fix this bug, but also to simplify the
code and make it similar to the video data processing code part (which allows
further code abstraction/unification in the future).
The changes have been tested with device "Hauppauge HVR-900".
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This field is used to keep track of the current memory position in the buffer,
not in the dma queue, so move it to right place.
This also allows us to get rid of the struct em28xx_dmaqueue pointer parameter
in functions em28xx_copy_video() and em28xx_copy_vbi().
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
get_next_buf() and vbi_get_next_buf() do exactly the same just with a
different dma queue and buffer. Saving the new buffer pointer back to the
device struct in em28xx_urb_data_copy() instead of doing this from inside
these functions makes it possible to get rid of one of them.
Also refactor the function parameters and return type:
- pass a pointer to struct em28xx as parameter (instead of obtaining the
pointer from the dma queue pointer with the container_of macro) like we do
it in all other functions
- instead of using a pointer-pointer, return the pointer to the new buffer
as return value of the function
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
em28xx_urb_data_copy_vbi() is actually an extended version of
em28xx_urb_data_copy(). With the preceding fixes and improvements, it works
fine with both, vbi and non-vbi data streams without performance impacts.
So rename em28xx_urb_data_copy_vbi() to em28xx_urb_data_copy(), delete the
the old implementation of em28xx_urb_data_copy() and change the code to use
this function for both data stream types.
Tested with "SilverCrest 1.3 MPix webcam" (progressive, non-vbi) and
"Hauppauge HVR-900 (65008/A1C0)" (interlaced, vbi enabled and disabled).
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Set capture type to 1 (video start) when the video frame start header is
detected. This bug didn't cause any trouble, because this type of header is
never received in vbi mode.
Fix it, because we want to use this function with disabled vbi in the future.
Also start with capture type -1 to avoid processing of corrupted/incomplete
frame data which is usually received at streaming start (especially when
USB bulk transfers are used).
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The header check/removal code at the end of function em28xx_urb_data_copy_vbi()
is obsolete, because this is already done earlier in this function.
In fact it is incomplete (doesn't check for vbi header) and causes trouble
when the first data bytes are the same as header bytes (which is fortunately
very unlikely).
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
By default, isoc transfers are used if possible.
With the new module parameter, bulk can be selected as the
preferred USB transfer type.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current enpoint logic ignores all bulk endpoints and uses
a fixed mapping between endpint addresses and the supported
data stream types (analog/audio/DVB):
Ep 0x82, isoc => analog
Ep 0x83, isoc => audio
Ep 0x84, isoc => DVB
Now that the code can also do bulk transfers, the endpoint
logic has to be extended to also consider bulk endpoints.
The new logic preserves backwards compatibility and reflects
the endpoint configurations we have seen so far:
Ep 0x82, isoc => analog
Ep 0x82, bulk => analog
Ep 0x83, isoc* => audio
Ep 0x84, isoc => digital
Ep 0x84, bulk => analog or digital**
(*: audio should always be isoc)
(**: analog, if ep 0x82 is isoc, otherwise digital)
[mchehab@redhat.com: Fix a CodingStyle issue: don't break strings
into separate lines]
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Extend function em28xx_set_alternate:
- use alternate setting 0 for bulk transfers as default
- respect module parameter 'alt'=0 for bulk transfers
- set max_packet_size to 512 bytes for bulk transfers
[mchehab@redhat.com: Fix a CodingStyle issue: don't break strings
into separate lines]
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The URB data processing for DVB bulk transfers is very similar to
what is done with isoc transfers, so create a common function that
works with both transfer types based on the existing isoc function.
Tested with device Hauppauge HVR-930c.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The URB data processing for bulk transfers is very similar to what
is done with isoc transfers, so create a common function that works
with both transfer types based on the existing isoc function.
[mchehab@redhat.com: Fix a CodingStyle issue: don't break strings
into separate lines]
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The URB data processing for bulk transfers is very similar to what
is done with isoc transfers, so create a common function that works
with both transfer types based on the existing isoc function.
[mchehab@redhat.com: Fix a CodingStyle issue: don't break strings
into separate lines]
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This check is already done in the URB handler
em28xx_irq_callback before calling these functions.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[mchehab@redhat.com: Fix a CodingStyle issue: don't break strings
into separate lines]
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- rename em28xx_init_isoc to em28xx_init_usb_xfer
- add parameter for isoc/bulk transfer selection which is passed to em28xx_alloc_urbs
- rename local variable isoc_buf to usb_bufs
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rename the existing function for isoc transfers em28xx_init_isoc
to em28xx_init_usb_xfer and extend it.
URB allocation and setup is now done depending on the USB
transfer type, which is selected with a new function parameter.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This function will be used to uninitialize USB bulk transfers, too.
Also rename the local variable isoc_bufs to usb_bufs.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
em28xx_irq_callback can be used for isoc and bulk transfers.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It isn't used anymore and uses constants which no longer exist.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Also rename the corresponding field isoc_ctl in struct em28xx
to usb_ctl.
We will use this struct for USB bulk transfers, too.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It will be used for USB bulk transfers, too.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rename EM28XX_NUM_PACKETS to EM28XX_NUM_ISOC_PACKETS and
EM28XX_DVB_MAX_PACKETS to EM28XX_DVB_NUM_ISOC_PACKETS to
clarify that these values are used only for isoc usb transfers.
Also use the term num_packets instead of max_packets, as this
is how these values are used and called in struct urb.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
em28xx_copy_video uses a wrong offset for the target buffer
when copying the data from an USB isoc packet. This happens
only for the second and all following lines in the packet.
The reason why this bug doesn't cause image corruption with
my test device (SilverCrest Webcam 1.3 MPix) is, that this
device never sends any packets that cross the end of a line.
I don't know if all devices behave like this, so this patch
should be considered for stable.
With the upcoming patches to add support for USB bulk transfers,
em28xx_copy_video will be called once per URB, which will
always trigger this bug.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When em28xx_ir_init() fails due to an configuration error, it frees the memory
of struct em28xx_IR *ir, but doesn't set the corresponding pointer in the
device struct to NULL.
On device removal, em28xx_ir_fini() gets called, which then calls
rc_unregister_device() with a pointer to freed memory.
Fixes bug 26572 (http://bugzilla.kernel.org/show_bug.cgi?id=26572)
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Newer em28xx chipsets (em2874 and upper) are capable of supporting
RC6 codes, on both mode 0 (command mode, 16 bits payload size, similar
to RC5, also called "Philips mode") and mode 6a (OEM command mode,
with offers a few alternatives with regards to the payload size).
I don't have any mode 6a control ATM to test it, so, I opted to add
support only to mode 0.
After this patch, adding support to mode 6a should not be hard.
Tested with a Philips television remote controller.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
By disabling the NEC parity check, it is possible to handle all 3 NEC
protocol variants (32, 24 or 16 bits).
Change the driver in order to handle all of them.
Unfortunately, em2860/em2863 provide only 16 bits for the IR scancode,
even when NEC parity is disabled. So, this change should affect only
em2874 and newer devices, with provides up to 32 bits for the scancode.
Tested with one NEC-16, one NEC-24 and one RC5 IR.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I noticed that the EM28XX DVB driver doesn't auto select all of the
appropriate DVB tuner modules required. In particular I needed
DVB_LGDT3305 for my a340, but it looks like DVB_MT352 + DVB_S5H1409 were
missing as well.
Signed-Off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
display an error message if either tuner_i2c_addr or demod_i2c_addr
are not specified in the tda10071_config structure
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert drivers using wall clock time (CLOCK_REALTIME) to timestamp from the
monotonic timer (CLOCK_MONOTONIC).
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The RC_TYPE_* defines are currently used both where a single protocol is
expected and where a bitmap of protocols is expected.
Functions like rc_keydown() and functions which add/remove entries to the
keytable want a single protocol. Future userspace APIs would also
benefit from numeric protocols (rather than bitmap ones). Keytables are
smaller if they can use a small(ish) integer rather than a bitmap.
Other functions or struct members (e.g. allowed_protos,
enabled_protocols, etc) accept multiple protocols and need a bitmap.
Using different types reduces the risk of programmer error. Using a
protocol enum whereever possible also makes for a more future-proof
user-space API as we don't need to worry about a sufficient number of
bits being available (e.g. in structs used for ioctl() calls).
The use of both a number and a corresponding bit is dalso one in e.g.
the input subsystem as well (see all the references to set/clear bit when
changing keytables for example).
This patch separate the different usages in preparation for
upcoming patches.
Where a single protocol is expected, enum rc_type is used; where one or more
protocol(s) are expected, something like u64 is used.
The patch has been rewritten so that the format of the sysfs "protocols"
file is no longer altered (at the loss of some detail). The file itself
should probably be deprecated in the future though.
Signed-off-by: David Härdeman <david@hardeman.nu>
Cc: Andy Walls <awalls@md.metrocast.net>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Antti Palosaari <crope@iki.fi>
Cc: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This intializes the card just like the windows driver does
- the "HTC USB XS HD" uses the same firmware as the "HTC Stick HD";
- both have different GPIO and reg init sequences;
Tested only with DVB-C.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Applied on the top of changeset 782cd9e, as some of those patches
depend on some fixes that went via -arm tree.
* staging/for_v3.7: (109 commits)
[media] m5mols: Add missing #include <linux/sizes.h>
[media] stk1160: Add support for S-Video input
Revert "[media] omap3isp: Replace cpu_is_omap3630() with ISP revision check"
[media] dvb: LNA implementation changes
[media] v4l2-ioctl: fix W=1 warnings
[media] v4l2-ioctl: add blocks check for VIDIOC_SUBDEV_G/S_EDID
[media] omap3isp: Fix compilation error in ispreg.h
[media] rc-msi-digivox-ii: Add full scan keycodes
[media] cx25821: testing the wrong variable
[media] tda18271-common: hold the I2C adapter during write transfers
[media] ds3000: add module parameter to force firmware upload
[media] drivers/media: Remove unnecessary semicolon
[media] winbond: remove space from driver name
[media] iguanair: cannot send data from the stack
[media] omap3isp: Replace cpu_is_omap3630() with ISP revision check
[media] dvb-usb: print small buffers via %*ph
[media] uvc: Add return code check at vb2_queue_init()
[media] em28xx: Replace memcpy with struct assignment
[media] bt8xx: Add video4linux control V4L2_CID_COLOR_KILLER
[media] mem2mem_testdev: Use devm_kzalloc() in probe
...
* use dvb property cache
* implement get (thus API minor++)
* PCTV 290e: 1=LNA ON, all the other values LNA OFF
Also fix PCTV 290e LNA comment, it is disabled by default
Hans and Mauro proposed use of cache implementation of get as they
were planning to extend LNA usage for analog side too.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pull media updates from Mauro Carvalho Chehab:
"The first part of the media updates for Kernel 3.7.
This series contain:
- A major tree renaming patch series: now, drivers are organized
internally by their used bus, instead of by V4L2 and/or DVB API,
providing a cleaner driver location for hybrid drivers that
implement both APIs, and allowing to cleanup the Kconfig items and
make them more intuitive for the end user;
- Media Kernel developers are typically very lazy with their duties
of keeping the MAINTAINERS entries for their drivers updated. As
now the tree is more organized, we're doing an effort to add/update
those entries for the drivers that aren't currently orphan;
- Several DVB USB drivers got moved to a new DVB USB v2 core; the new
core fixes several bugs (as the existing one that got bitroted).
Now, suspend/resume finally started to work fine (at least with
some devices - we should expect more work with regards to it);
- added multistream support for DVB-T2, and unified the API for
DVB-S2 and ISDB-S. Backward binary support is preserved;
- as usual, a few new drivers, some V4L2 core improvements and lots
of drivers improvements and fixes.
There are some points to notice on this series:
1) you should expect a trivial merge conflict on your tree, with the
removal of Documentation/feature-removal-schedule.txt: this series
would be adding two additional entries there. I opted to not
rebase it due to this recent change;
2) With regards to the PCTV 520e udev-related breakage, I opted to
fix it in a way that the patches can be backported to 3.5 even
without your firmware fix patch. This way, Greg doesn't need to
rush backporting your patch (as there are still the firmware cache
and firmware path customization issues to be addressed there).
I'll send later a patch (likely after the end of the merge window)
reverting the rest of the DRX-K async firmware request, fully
restoring its original behaviour to allow media drivers to
initialize everything serialized as before for 3.7 and upper.
3) I'm planning to work on this weekend to test the DMABUF patches
for V4L2. The patches are on my queue for several Kernel cycles,
but, up to now, there is/was no way to test the series locally.
I have some concerns about this particular changeset with regards
to security issues, and with regards to the replacement of the old
VIDIOC_OVERLAY ioctl's that is broken on modern systems, due to
GPU drivers change. The Overlay API allows direct PCI2PCI
transfers from a media capture card into the GPU framebuffer, but
its API is crappy. Also, the only existing X11 driver that
implements it requires a XV extension that is not available
anymore on modern drivers. The DMABUF can do the same thing, but
with it is promising to be a properly-designed API. If I can
successfully test this series and be happy with it, I should be
asking you to pull them next week."
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (717 commits)
em28xx: regression fix: use DRX-K sync firmware requests on em28xx
drxk: allow loading firmware synchrousnously
em28xx: Make all em28xx extensions to be initialized asynchronously
[media] tda18271: properly report read errors in tda18271_get_id
[media] tda18271: delay IR & RF calibration until init() if delay_cal is set
[media] MAINTAINERS: add Michael Krufky as tda827x maintainer
[media] MAINTAINERS: add Michael Krufky as tda8290 maintainer
[media] MAINTAINERS: add Michael Krufky as cxusb maintainer
[media] MAINTAINERS: add Michael Krufky as lg2160 maintainer
[media] MAINTAINERS: add Michael Krufky as lgdt3305 maintainer
[media] MAINTAINERS: add Michael Krufky as mxl111sf maintainer
[media] MAINTAINERS: add Michael Krufky as mxl5007t maintainer
[media] MAINTAINERS: add Michael Krufky as tda18271 maintainer
[media] s5p-tv: Report only multi-plane capabilities in vidioc_querycap
[media] s5p-mfc: Fix misplaced return statement in s5p_mfc_suspend()
[media] exynos-gsc: Add missing static storage class specifiers
[media] exynos-gsc: Remove <linux/version.h> header file inclusion
[media] s5p-fimc: Fix incorrect condition in fimc_lite_reqbufs()
[media] s5p-tv: Fix potential NULL pointer dereference error
[media] s5k6aa: Fix possible NULL pointer dereference
...
This kind of memcpy() is error-prone and its
replacement with a struct assignment is prefered.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As em28xx-dvb will always be initialized asynchronously, there's
no need anymore for a separate thread to load the DRX-K firmware.
Fixes a known regression with kernel 3.6 with tda18271 driver
and asynchronous DRX-K firmware load.
Antti tested it with the following hardware:
Hauppauge WinTV HVR 930C
MaxMedia UB425-TC
PCTV QuatroStick nano (520e)
Tested-by: Antti Palosaari <crope@iki.fi>
Cc: stable@kernel.org # for Kernel 3.6 - please note that driver location has changed
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
em28xx-dvb, em28xx-alsa and em28xx-ir are typically initialized
asyncrhronously. The exception for it is when those modules
are loaded before em28xx (or before an em28xx card insertion) or
when they're built in.
Make the extentions to always load asynchronously. That allows
having all DVB firmwares loaded synchronously with udev-182.
Antti tested it with the following hardware:
Hauppauge WinTV HVR 930C
MaxMedia UB425-TC
PCTV QuatroStick nano (520e)
Tested-by: Antti Palosaari <crope@iki.fi>
Cc: stable@kernel.org # for Kernel 3.6 - please note that driver location has changed
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It was a bug that could cause oops if demodulator attach was
failed.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is fallback condition as GPIOLIB seems to be disabled by default.
Better solution is needed, maybe GPIOLIB could be enabled by default?
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make LNA run-time switching possible for PCTV nanoStick T2 290e!
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently there is LNA behind cxd2820r demodulator GPIO. Use
Kernel GPIO interface to access those GPIOs.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Write-only ioctls should have a const argument in the ioctl op.
Do this conversion for vidioc_s_audio.
Adding const for write-only ioctls was decided during the 2012 Media Workshop.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of having 3 options to allow customizing the media
sub-drivers (tuners, I2C drivers, frontends), merge all of
them into just one.
That simplifies the life for users, as they can just keep
this untouched.
Life for developers is also simpler, as there's now just
one Kconfig item to remember, for the ancillary sub-drivers
providing supports for chips that could change from one
board design to another.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On a few places, := were using instead of +=, causing drivers to
not compile.
While here, standardize the usage of += on all cases where multiple
lines are needed, and for obj-y/obj-m targets, and := when just one
line is needed, on <module>-obj rules.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Identified-by: Antti Polosaari <crope@iki.fi>
Tested-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We need to move the unlock before the kfree(dev);
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rename all USB drivers with their own directory under
drivers/media/video into drivers/media/usb and update the
building system.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil