Add a net argument to inet_lookup and propagate it further
into lookup calls. Plus tune the __inet_check_established.
The dccp and inet_diag, which use that lookup functions
pass the init_net into them.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Needed to propagate it down to the __ip_route_output_key.
Signed_off_by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This one is used in quite many places in the networking code and
seems to big to be inline.
After the patch net/ipv4/build-in.o loses ~650 bytes:
add/remove: 2/0 grow/shrink: 0/5 up/down: 461/-1114 (-653)
function old new delta
__inet_hash_nolisten - 282 +282
__inet_hash - 179 +179
tcp_sacktag_write_queue 2255 2254 -1
__inet_lookup_listener 284 274 -10
tcp_v4_syn_recv_sock 755 493 -262
tcp_v4_hash 389 35 -354
inet_hash_connect 1086 599 -487
This version addresses the issue pointed by Eric, that
while being inline this function was optimized by gcc
in respect to the 'listen_possible' argument.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The option parsing code currently only parses on full sk's. This causes a problem for
options sent during the initial handshake (in particular timestamps and feature-negotiation
options). Therefore, this patch extends the option parsing code with an additional argument
for request_socks: if it is non-NULL, options are parsed on the request socket, otherwise
the normal path (parsing on the sk) is used.
Subsequent patches, which implement feature negotiation during connection setup, make use
of this facility.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the following problem: client connects to peer which has no DCCP
enabled or loaded; ICMP error messages ("Protocol Unavailable") can be seen
on the wire, but the application hangs. Reason: ICMP packets don't get through
to dccp_v4_err.
When reporting errors, a sequence number check is made for the DCCP packet
that had caused an ICMP error to arrive.
Such checks can not be made if the socket is in state LISTEN, RESPOND (which
in the implementation is the same as LISTEN), or REQUEST, since update_gsr()
has not been called in these states, hence the sequence window is 0..0.
This patch fixes the problem by adding the REQUEST state as another exemption
to the window check. The error reporting now works as expected on connecting.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
This fixes a problem when analysing erroneous packets in dccp_v{4,6}_err:
* dccp_hdr_seq currently takes an skb
* however, the transport headers in the skb are shifted, due to the
preceding IPv4/v6 header.
Fixed for v4 and v6 by changing dccp_hdr_seq to take a struct dccp_hdr as
argument. Verified that the correct sequence number is now reported in the
error handler.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Now that we have this new macro, use it where possible.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes two bugs in processing of connection-Requests in
v{4,6}_conn_request:
1. Due to using the variable `reset_code', the Reset code generated
internally by dccp_parse_options() is overwritten with the
initialised value ("Too Busy") of reset_code, which is not what is
intended.
2. When receiving a connection-Request on a multicast or broadcast
address, no Reset should be generated, to avoid storms of such
packets. Instead of jumping to the `drop' label, the
v{4,6}_conn_request functions now return 0. Below is why in my
understanding this is correct:
When the conn_request function returns < 0, then the caller,
dccp_rcv_state_process(), returns 1. In all instances where
dccp_rcv_state_process is called (dccp_v4_do_rcv, dccp_v6_do_rcv,
and dccp_child_process), a return value of != 0 from
dccp_rcv_state_process() means that a Reset is generated.
If on the other hand the conn_request function returns 0, the
packet is discarded and no Reset is generated.
Note: There may be a related problem when sending the Response, due to
the following.
if (dccp_v6_send_response(sk, req, NULL))
goto drop_and_free;
/* ... */
drop_and_free:
return -1;
In this case, if send_response fails due to transmission errors, the
next thing that is generated is a Reset with a code "Too Busy". I
haven't been able to conjure up such a condition, but it might be good
to change the behaviour here also (not done by this patch).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This factors code common to dccp_v{4,6}_ctl_send_reset into a separate function,
and adds support for filling in the Data 1 ... Data 3 fields from RFC 4340, 5.6.
It is useful to have this separate, since the following Reset codes will always
be generated from the control socket rather than via dccp_send_reset:
* Code 3, "No Connection", cf. 8.3.1;
* Code 4, "Packet Error" (identification for Data 1 added);
* Code 5, "Option Error" (identification for Data 1..3 added, will be used later);
* Code 6, "Mandatory Error" (same as Option Error);
* Code 7, "Connection Refused" (what on Earth is the difference to "No Connection"?);
* Code 8, "Bad Service Code";
* Code 9, "Too Busy";
* Code 10, "Bad Init Cookie" (not used).
Code 0 is not recommended by the RFC, the following codes would be used in
dccp_send_reset() instead, since they all relate to an established DCCP connection:
* Code 1, "Closed";
* Code 2, "Aborted";
* Code 11, "Aggression Penalty" (12.3).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
This replaces normal addition with mod-48 addition so that sequence number
wraparound is respected.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
This trivial patch removes the unneeded pointer newdp, which is never used.
Signed-off-by: Micah Gruber <micah.gruber@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do this even for non-blocking sockets. This avoids the silly -EAGAIN
that applications can see now, even for non-blocking sockets in some
cases (f.e. connect()).
With help from Venkat Tekkirala.
Signed-off-by: David S. Miller <davem@davemloft.net>
That accumulated over the last months hackaton, shame on me for not
using git-apply whitespace helping hand, will do that from now on.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This reaps the benefit of the earlier patch, which changed the type of
CCID 3 states to use enums, in that many conditions are now simplified
and the number of possible (unexpected) values is greatly reduced.
In a few instances, this also allowed to simplify pre-conditions; where
care has been taken to retain logical equivalence.
[DCCP]: Introduce a consistent BUG/WARN message scheme
This refines the existing set of DCCP messages so that
* BUG(), BUG_ON(), WARN_ON() have meaningful DCCP-specific counterparts
* DCCP_CRIT (for severe warnings) is not rate-limited
* DCCP_WARN() is introduced as rate-limited wrapper
Using these allows a faster and cleaner transition to their original
counterparts once the code has matured into a full DCCP implementation.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Spotted by Ian McDonald, tentatively fixed by Gerrit Renker:
http://www.mail-archive.com/dccp%40vger.kernel.org/msg00599.html
Rewritten not to unroll sk_receive_skb, in the common case, i.e. no lock
debugging, its optimized away.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This patch does not change code; it performs some trivial clean/tidy-ups:
* removal of a `debug_prefix' string in favour of the
already existing dccp_role(sk)
* add documentation of structures and constants
* separated out the cases for invalid packets (step 1
of the packet validation)
* removing duplicate statements
* combining declaration & initialisation
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Throughout the TCP/DCCP (and tunnelling) code, it often happens that the
return code of a transmit function needs to be tested against NET_XMIT_CN
which is a value that does not indicate a strict error condition.
This patch uses a macro for these recurring situations which is consistent
with the already existing macro net_xmit_errno, saving on duplicated code.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This
* resolves a FIXME - DCCPv6 connections started all with
an initial sequence number of 1;
* provides a redirection `secure_dccpv6_sequence_number'
in case the init_sequence_v6 code should be updated later;
* concentrates the update of S.GAR into dccp_connect_init();
* removes a duplicate dccp_update_gss() in ipv4.c;
* uses inet->dport instead of usin->sin_port, due to the
following assignment in dccp_v4_connect():
inet->dport = usin->sin_port;
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This patch removes the following redundancies:
1) The test skb->protocol == htons(ETH_P_IPV6) in dccp_v6_init_sequence
is always true since
* dccp_v6_conn_request() is the only calling function
* dccp_v6_conn_request() redirects all skb's with ETH_P_IP to
dccp_v4_conn_request()
2) The first argument, `struct sock *sk', of dccp_v{4,6}_init_sequence()
is never used.
(This is similar for tcp_v{4,6}_init_sequence, an analogous patch has been
submitted to netdev and merged.)
By the way - are the `sport' / `dport' arguments in the right order?
I have made them consistent among calls but they seem to be in the
reverse order.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
In order to make their function clearer and obtain a consistent naming
scheme to identify sysctls, all existing DCCP sysctls have been prefixed
with `sysctl_dccp', following the same convention as used by TCP.
Feature-specific sysctls retain the `feat' in the middle, although the
`default' has been dropped, since it is obvious from use.
Also removed a duplicate `dccp_feat_default_sequence_window' in ipv4.c.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This patch does the following:
a) introduces variable-length checksums as specified in [RFC 4340, sec. 9.2]
b) provides necessary socket options and documentation as to how to use them
c) basic support and infrastructure for the Minimum Checksum Coverage feature
[RFC 4340, sec. 9.2.1]: acceptability tests, user notification and user
interface
In addition, it
(1) fixes two bugs in the DCCPv4 checksum computation:
* pseudo-header used checksum_len instead of skb->len
* incorrect checksum coverage calculation based on dccph_x
(2) removes dccp_v4_verify_checksum() since it reduplicates code of the
checksum computation; code calling this function is updated accordingly.
(3) now uses skb_checksum(), which is safer than checksum_partial() if the
sk_buff has is a non-linear buffer (has pages attached to it).
(4) fixes an outstanding TODO item:
* If P.CsCov is too large for the packet size, drop packet and return.
The code has been tested with applications, the latest version of tcpdump now
comes with support for partial DCCP checksums.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Sorts out the comments for processing steps 2,3 in section 8.5 of RFC 4340.
All comments have been updated against this document, and the reference to step
2 has been made consistent throughout the files.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This patch removes two functions, the send_ack functions of request_sock,
which are not called/used by the DCCP code. It is correct that these
functions are not called, below is a justification why calling these
functions (on a passive socket in the LISTEN/RESPOND state) would mean
a DCCP protocol violation.
A) Background: using request_sock in TCP:
This is a code simplification and was singled out from the
DCCPv6 Oops patch on
http://www.mail-archive.com/dccp@vger.kernel.org/msg00600.html
It mainly makes the code consistent between ipv{4,6}.c for the functions
dccp_v4_rcv
dccp_v6_rcv
and removes the do_time_wait label to simplify code somewhat.
Commiter note: fixed up a compile problem, trivial.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This is a code simplification:
it combines three often recurring operations into one inline function,
* allocate `len' bytes header space in skb
* fill these `len' bytes with zeroes
* cast the start of this header space as dccp_hdr
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
We currently allocate a fixed size (TCP_SYNQ_HSIZE=512) slots hash table for
each LISTEN socket, regardless of various parameters (listen backlog for
example)
On x86_64, this means order-1 allocations (might fail), even for 'small'
sockets, expecting few connections. On the contrary, a huge server wanting a
backlog of 50000 is slowed down a bit because of this fixed limit.
This patch makes the sizing of listen hash table a dynamic parameter,
depending of :
- net.core.somaxconn tunable (default is 128)
- net.ipv4.tcp_max_syn_backlog tunable (default : 256, 1024 or 128)
- backlog value given by user application (2nd parameter of listen())
For large allocations (bigger than PAGE_SIZE), we use vmalloc() instead of
kmalloc().
We still limit memory allocation with the two existing tunables (somaxconn &
tcp_max_syn_backlog). So for standard setups, this patch actually reduce RAM
usage.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updates the references to spec documents throughout the code, taking into
account that
* the DCCP, CCID 2, and CCID 3 drafts all became RFCs in March this year
* RFC 1063 was obsoleted by RFC 1191
* draft-ietf-tcpimpl-pmtud-0x.txt was published as an Informational
RFC, RFC 2923 on 2000-09-22.
All references verified.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I think I got the cause for the Oops observed in
http://www.mail-archive.com/dccp@vger.kernel.org/msg00578.html
The problem is always with applications listening on PF_INET6 sockets. Apart
from the mentioned oops, I observed another one one, triggered at irregular
intervals via timer interrupt:
run_timer_softirq -> dccp_keepalive_timer
-> inet_csk_reqsk_queue_prune
-> reqsk_free
-> dccp_v6_reqsk_destructor
The latter function is the problem and is also the last function to be called
in said kernel panic.
In any case, there is a real problem with allocating the right request_sock
which is what this patch tackles.
It fixes the following problem:
- application listens on PF_INET6
- DCCPv4 packet comes in, is handed over to dccp_v4_do_rcv, from there
to dccp_v4_conn_request
Now: socket is PF_INET6, packet is IPv4. The following code then furnishes the
connection with IPv6 - request_sock operations:
req = reqsk_alloc(sk->sk_prot->rsk_prot);
The first problem is that all further incoming packets will get a Reset since
the connection can not be looked up.
The second problem is worse:
--> reqsk_alloc is called instead of inet6_reqsk_alloc
--> consequently inet6_rsk_offset is never set (dangling pointer)
--> the request_sock_ops are nevertheless still dccp6_request_ops
--> destructor is called via reqsk_free
--> dccp_v6_reqsk_destructor tries to free random memory location (inet6_rsk_offset not set)
--> panic
I have tested this for a while, DCCP sockets are now handled correctly in all
three scenarios (v4/v6 only/v4-mapped).
Commiter note: I've added the dccp_request_sock_ops forward declaration to keep
the tree building and to reduce the size of the patch for 2.6.19,
later I'll move the functions to the top of the affected source
code to match what we have in the TCP counterpart, where this
problem hasn't existed in the first place, dumb me not to have
done the same thing on DCCP land 8)
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
annotated address arguments (port number left alone for now); ditto
for inferred net-endian variables in callers.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This has been discussed on dccp@vger and removes the necessity for applications
to supply service codes in each and every case.
If an application does not want to provide a service code, that's fine, it will
be given 0. Otherwise, service codes can be set via socket options as before.
This patch has been tested using various client/server configurations
(including listening on multiple service codes).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Right now most inet_lookup_* functions take a host-order hnum instead
of a network-order dport because that's how it is represented
internally.
This means that users of these functions have to be careful about
using the right byte-order. To add more confusion, inet_lookup takes
a network-order dport unlike all other functions.
So this patch changes all visible inet_lookup functions to take a
dport and move all dport->hnum conversion inside them.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This automatically labels the TCP, Unix stream, and dccp child sockets
as well as openreqs to be at the same MLS level as the peer. This will
result in the selection of appropriately labeled IPSec Security
Associations.
This also uses the sock's sid (as opposed to the isec sid) in SELinux
enforcement of secmark in rcv_skb and postroute_last hooks.
Signed-off-by: Venkat Yekkirala <vyekkirala@TrustedCS.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This labels the flows that could utilize IPSec xfrms at the points the
flows are defined so that IPSec policy and SAs at the right label can
be used.
The following protos are currently not handled, but they should
continue to be able to use single-labeled IPSec like they currently
do.
ipmr
ip_gre
ipip
igmp
sit
sctp
ip6_tunnel (IPv6 over IPv6 tunnel device)
decnet
Signed-off-by: Venkat Yekkirala <vyekkirala@TrustedCS.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using the default sequence window size (100) I got the following in
my logs:
Jun 22 14:24:09 localhost kernel: [ 1492.114775] DCCP: Step 6 failed for
DATA packet, (LSWL(6279674225) <= P.seqno(6279674749) <=
S.SWH(6279674324)) and (P.ackno doesn't exist or LAWL(18798206530) <=
P.ackno(1125899906842620) <= S.AWH(18798206548), sending SYNC...
Jun 22 14:24:09 localhost kernel: [ 1492.115147] DCCP: Step 6 failed for
DATA packet, (LSWL(6279674225) <= P.seqno(6279674750) <=
S.SWH(6279674324)) and (P.ackno doesn't exist or LAWL(18798206530) <=
P.ackno(1125899906842620) <= S.AWH(18798206549), sending SYNC...
I went to alter the default sysctl and it didn't take for new sockets.
Below patch fixes this.
I think the default is too low but it is what the DCCP spec specifies.
As a side effect of this my rx speed using iperf goes from about 2.8 Mbits/sec
to 3.5. This is still far too slow but it is a step in the right direction.
Compile tested only for IPv6 but not particularly complex change.
Signed off by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
we dont free req if we cant parse the options.
This fixes coverity bug id #1046
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
No code changes, just tidying up, in some cases moving EXPORT_SYMBOLs
to just after the function exported, etc.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends {get|set}sockopt compatibility layer in order to
move protocol specific parts to their place and avoid huge universal
net/compat.c file in the future.
Signed-off-by: Dmitry Mishin <dim@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merging it with its only user: dccp_v[46]_reqsk_send_ack.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using this also provides opportunities for introducing
inet_csk_alloc_skb that would call alloc_skb, account it to the sock
and skb_reserve(max_header), but I'll leave this for later, for now
using sk_prot->max_header consistently is enough.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consolidating open coded sequences in tcp and dccp, v4 and v6.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I guess I forgot to add it, nah, now it just works:
18:04:33.274066 IP6 ::1.1476 > ::1.5001: request (service=0)
18:04:33.334482 IP6 ::1.5001 > ::1.1476: reset (code=bad_service_code)
Ditched IP_DCCP_UNLOAD_HACK, as now we would have to do it for both
IPv6 and IPv4, so I'll come up with another way for freeing the
control sockets in upcoming changesets.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no reason for struct dccp_v4_prot being global.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch in place we can break down the complexity by better
compartmentalizing the code that is common to ipv6 and ipv4.
Now we have these modules:
Module Size Used by
dccp_diag 1344 0
inet_diag 9448 1 dccp_diag
dccp_ccid3 15856 0
dccp_tfrc_lib 12320 1 dccp_ccid3
dccp_ccid2 5764 0
dccp_ipv4 16996 2
dccp 48208 4 dccp_diag,dccp_ccid3,dccp_ccid2,dccp_ipv4
dccp_ipv6 still requires dccp_ipv4 due to dccp_ipv6_mapped, that is
the next target to work on the "hey, ipv4 is legacy, I only want ipv6
dude!" direction.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dccp_make_response is shared by ipv4/6 and the ipv6 code was
recalculating the checksum, not good, so move the dccp_v4_checksum
call to dccp_v4_send_response.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As this is used by both ipv4 and ipv6 and is not ipv4 specific.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing one more ipv6 uses ipv4 stuff case in dccp land.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Renaming it to dccp_send_reset and moving it from the ipv4 specific
code to the core dccp code.
This fixes some bugs in IPV6 where timers would send v4 resets, etc.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So that dccp_feat_clean doesn't get confused with uninitialized
list_heads.
Noticed when testing with no ccid kernel modules.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This also fixes the layout of dccp_hdr short sequence numbers, problem
was not fatal now as we only support long (48 bits) sequence numbers.
Signed-off-by: Andrea Bittau <a.bittau@cs.ucl.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. No need for ->ccid_init nor ->ccid_exit, this is what module_{init,exit}
does and anynways neither ccid2 nor ccid3 were using it.
2. Rename struct ccid to struct ccid_operations and introduce struct ccid
with a pointer to ccid_operations and rigth after it the rx or tx
private state.
3. Remove the pointer to the state of the half connections from struct
dccp_sock, now its derived thru ccid_priv() from the ccid pointer.
Now we also can implement the setsockopt for changing the CCID easily as
no ccid init routines can affect struct dccp_sock in any way that prevents
other CCIDs from working if a CCID switch operation is asked by apps.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Original work by Andrea Bittau, Arnaldo Melo cleaned up and fixed several
issues on the merge process.
For now CCID2 was turned the default for all SOCK_DCCP connections, but this
will be remedied soon with the merge of the feature negotiation code.
Signed-off-by: Andrea Bittau <a.bittau@cs.ucl.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplifying the code a bit as we're always using DCCP_MAX_ACKVEC_LEN.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_route_newports uses the struct flowi from the struct rtable returned
by ip_route_connect for the new route lookup and just replaces the port
numbers if they have changed. If an IPsec policy exists which doesn't match
port 0 the struct flowi won't have the proto field set and no xfrm lookup
is done for the changed ports.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle NAT of decapsulated IPsec packets by reconstructing the struct flowi
of the original packet from the conntrack information for IPsec policy
checks.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep the conntrack reference until policy checks have been performed for
IPsec NAT support. The reference needs to be dropped before a packet is
queued to avoid having the conntrack module unloadable.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
To help in reducing the number of include dependencies, several files were
touched as they were getting needed headers indirectly for stuff they use.
Thanks also to Alan Menegotto for pointing out that net/dccp/proto.c had
linux/dccp.h include twice.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Its common enough to to justify that, TCP still can't use it as it has the
prequeueing stuff, still to be made generic in the not so distant future :-)
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As DCCP needs to be called in the same spots.
Now we have a member in inet_sock (is_icsk), set at sock creation time from
struct inet_protosw->flags (if INET_PROTOSW_ICSK is set, like for TCP and
DCCP) to see if a struct sock instance is a inet_connection_sock for places
like the ones in ip_sockglue.c (v4 and v6) where we previously were looking if
sk_type was SOCK_STREAM, that is insufficient because we now use the same code
for DCCP, that has sk_type SOCK_DCCP.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Renaming it to inet_hash_connect, making it possible to ditch
dccp_v4_hash_connect and share the same code with TCP instead.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So that we can share several timewait sockets related functions and
make the timewait mini sockets infrastructure closer to the request
mini sockets one.
Next changesets will take advantage of this, moving more code out of
TCP and DCCP v4 and v6 to common infrastructure.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now we have the destructor (dccp_v4_reqsk_destructor) in our
request_sock_ops vtable.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Basically exports a similar set of functions as the one exported by
the non-AF specific TCP code.
In the process moved some non-AF specific code from dccp_v4_connect to
dccp_connect_init and moved the checksum verification from
dccp_invalid_packet to dccp_v4_rcv, so as to use it in dccp_v6_rcv
too.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And make the core DCCP code AF agnostic, just like TCP, now its time
to work on net/dccp/ipv6.c, we are close to the end!
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I hope to actually change this behaviour shortly but this will help
anybody grepping code at present.
Signed-off-by: Ian McDonald <imcdnzl@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Jesper Juhl <jesper.juhl@gmail.com>
This is the net/ part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in net/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Arnaldo Carvalho de Melo <acme@conectiva.com.br>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
This patch randomizes the port selected on bind() for connections
to help with possible security attacks. It should also be faster
in most cases because there is no need for a global lock.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Turns out the problem has nothing to do with use-after-free or double-free.
It's just that we're not clearing the CB area and DCCP unlike TCP uses a CB
format that's incompatible with IP.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Ian McDonald <imcdnzl@gmail.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Arnaldo and I agreed it could be applied now, because I have other
pending patches depending on this one (Thank you Arnaldo)
(The other important patch moves skc_refcnt in a separate cache line,
so that the SMP/NUMA performance doesnt suffer from cache line ping pongs)
1) First some performance data :
--------------------------------
tcp_v4_rcv() wastes a *lot* of time in __inet_lookup_established()
The most time critical code is :
sk_for_each(sk, node, &head->chain) {
if (INET_MATCH(sk, acookie, saddr, daddr, ports, dif))
goto hit; /* You sunk my battleship! */
}
The sk_for_each() does use prefetch() hints but only the begining of
"struct sock" is prefetched.
As INET_MATCH first comparison uses inet_sk(__sk)->daddr, wich is far
away from the begining of "struct sock", it has to bring into CPU
cache cold cache line. Each iteration has to use at least 2 cache
lines.
This can be problematic if some chains are very long.
2) The goal
-----------
The idea I had is to change things so that INET_MATCH() may return
FALSE in 99% of cases only using the data already in the CPU cache,
using one cache line per iteration.
3) Description of the patch
---------------------------
Adds a new 'unsigned int skc_hash' field in 'struct sock_common',
filling a 32 bits hole on 64 bits platform.
struct sock_common {
unsigned short skc_family;
volatile unsigned char skc_state;
unsigned char skc_reuse;
int skc_bound_dev_if;
struct hlist_node skc_node;
struct hlist_node skc_bind_node;
atomic_t skc_refcnt;
+ unsigned int skc_hash;
struct proto *skc_prot;
};
Store in this 32 bits field the full hash, not masked by (ehash_size -
1) Using this full hash as the first comparison done in INET_MATCH
permits us immediatly skip the element without touching a second cache
line in case of a miss.
Suppress the sk_hashent/tw_hashent fields since skc_hash (aliased to
sk_hash and tw_hash) already contains the slot number if we mask with
(ehash_size - 1)
File include/net/inet_hashtables.h
64 bits platforms :
#define INET_MATCH(__sk, __hash, __cookie, __saddr, __daddr, __ports, __dif)\
(((__sk)->sk_hash == (__hash))
((*((__u64 *)&(inet_sk(__sk)->daddr)))== (__cookie)) && \
((*((__u32 *)&(inet_sk(__sk)->dport))) == (__ports)) && \
(!((__sk)->sk_bound_dev_if) || ((__sk)->sk_bound_dev_if == (__dif))))
32bits platforms:
#define TCP_IPV4_MATCH(__sk, __hash, __cookie, __saddr, __daddr, __ports, __dif)\
(((__sk)->sk_hash == (__hash)) && \
(inet_sk(__sk)->daddr == (__saddr)) && \
(inet_sk(__sk)->rcv_saddr == (__daddr)) && \
(!((__sk)->sk_bound_dev_if) || ((__sk)->sk_bound_dev_if == (__dif))))
- Adds a prefetch(head->chain.first) in
__inet_lookup_established()/__tcp_v4_check_established() and
__inet6_lookup_established()/__tcp_v6_check_established() and
__dccp_v4_check_established() to bring into cache the first element of the
list, before the {read|write}_lock(&head->lock);
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Acked-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Isolating it, that will be used when we introduce a CCID2 (TCP-Like)
implementation.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As discussed in the dccp@vger mailing list:
Now applications have to use setsockopt(DCCP_SOCKOPT_SERVICE, service[s]),
prior to calling listen() and connect().
An array of unsigned ints can be passed meaning that the listening sock accepts
connection requests for several services.
With this we can ditch struct sockaddr_dccp and use only sockaddr_in (and
sockaddr_in6 in the future).
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving the setting of DCCP_SKB_CB(skb)->dccpd_reset_code to the places
where events happen that trigger sending a RESET packet.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To start the timestamps with 0.0ms, easing the integer maths in the CCIDs, this
probably will be reworked to use the to be introduced struct timeval_offset
infrastructure out of skb_get_timestamp, etc.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This makes the send rate calculations behave way more closely to what
is specified, with the jitter previously seen on x and x_recv
disappearing completely on non lossy setups.
This resembles the tcp_data_snd_check code, that possibly we'll end up
using in DCCP as well, perhaps moving this code to
inet_connection_sock.
For now I'm doing the simplest implementation tho.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is from a first audit, more eyeballs are more than welcome.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also fix step 6 when receiving SYNC or SYNCACK packets, i.e. we were not using
the updated swl.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With ugly ifdefs, etc, but this actually:
1. keeps the existing ABI, i.e. no need to recompile the iproute2
utilities if not interested in DCCP.
2. Provides all the tcp_diag functionality in DCCP, with just a
small patch that makes iproute2 support DCCP.
Of course I'll get this cleaned-up in time, but for now I think its
OK to be this way to quickly get this functionality.
iproute2-ss050808 patch at:
http://vger.kernel.org/~acme/iproute2-ss050808.dccp.patch
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using most of the infrastructure TCP uses, with a dccp_death_row,
etc. As per my current interpretation of the draft what we have with
this changeset seems to be all we need (or very close to it 8)).
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes nasty bug related to the retransmit timer (yeah, DCCP does
retransmits) firing too early.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yoshifumi Nishida <nishida@csl.sony.co.jp>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Development to this point was done on a subversion repository at:
http://oops.ghostprotocols.net:81/cgi-bin/viewcvs.cgi/dccp-2.6/
This repository will be kept at this site for the foreseable future,
so that interested parties can see the history of this code,
attributions, etc.
If I ever decide to take this offline I'll provide the full history at
some other suitable place.
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov