This allows you to specify the type of rgmii-id that will enable phy
internal delay in ethernet phy-mode.
This adds all RGMII cases to all of get_pinmode() except LD11, because LD11
SoC doesn't support RGMII due to the constraint of the hardware. When RGMII
phy mode is specified in the devicetree for LD11, the driver will abort
with an error.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building with PROVE_LOCKING=y, lockdep shows the following
dump message.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
...
Calling device_set_wakeup_enable() directly occurs this issue,
and it isn't necessary for initialization, so this patch creates
internal function __ave_ethtool_set_wol() and replaces with this
in ave_init() and ave_resume().
Fixes: 7200f2e3c9 ("net: ethernet: ave: Set initial wol state to disabled")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this change of_get_phy_mode() returned an enum,
phy_interface_t. On error, -ENODEV etc, is returned. If the result of
the function is stored in a variable of type phy_interface_t, and the
compiler has decided to represent this as an unsigned int, comparision
with -ENODEV etc, is a signed vs unsigned comparision.
Fix this problem by changing the API. Make the function return an
error, or 0 on success, and pass a pointer, of type phy_interface_t,
where the phy mode should be stored.
v2:
Return with *interface set to PHY_INTERFACE_MODE_NA on error.
Add error checks to all users of of_get_phy_mode()
Fixup a few reverse christmas tree errors
Fixup a few slightly malformed reverse christmas trees
v3:
Fix 0-day reported errors.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until calling register_netdev(), ndev->dev_name isn't specified, and
netdev_err() displays "(unnamed net_device)".
ave 65000000.ethernet (unnamed net_device) (uninitialized): invalid phy-mode setting
ave: probe of 65000000.ethernet failed with error -22
This replaces netdev_err() with dev_err() before calling register_netdev().
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "phy_mode" variable is an enum and in this context GCC treats it as
an unsigned int so the error handling is never triggered.
Fixes: 4c270b55a5 ("net: ethernet: socionext: add AVE ethernet driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: netdev@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was NVMEM support added to of_get_mac_address, so it could now
return ERR_PTR encoded error values, so we need to adjust all current
users of of_get_mac_address to this new fact.
While at it, remove superfluous is_valid_ether_addr as the MAC address
returned from of_get_mac_address is always valid and checked by
is_valid_ether_addr anyway.
Fixes: d01f449c00 ("of_net: add NVMEM support to of_get_mac_address")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several conflicts, seemingly all over the place.
I used Stephen Rothwell's sample resolutions for many of these, if not
just to double check my own work, so definitely the credit largely
goes to him.
The NFP conflict consisted of a bug fix (moving operations
past the rhashtable operation) while chaning the initial
argument in the function call in the moved code.
The net/dsa/master.c conflict had to do with a bug fix intermixing of
making dsa_master_set_mtu() static with the fixing of the tagging
attribute location.
cls_flower had a conflict because the dup reject fix from Or
overlapped with the addition of port range classifiction.
__set_phy_supported()'s conflict was relatively easy to resolve
because Andrew fixed it in both trees, so it was just a matter
of taking the net-next copy. Or at least I think it was :-)
Joe Stringer's fix to the handling of netns id 0 in bpf_sk_lookup()
intermixed with changes on how the sdif and caller_net are calculated
in these code paths in net-next.
The remaining BPF conflicts were largely about the addition of the
__bpf_md_ptr stuff in 'net' overlapping with adjustments and additions
to the relevant data structure where the MD pointer macros are used.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing MODULE_AUTHOR of ave driver and an entry to MAINTAINERS.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 26a4676faa ("arm64: mm: define NET_IP_ALIGN to 0"),
AVE controller affects this modification because the controller forces
to ignore lower 2bits of buffer start address, and make 2-byte headroom,
that is, data reception starts from (buffer + 2).
This patch defines AVE_FRAME_HEADROOM macro as hardware-specific value,
and replaces NET_IP_ALIGN with it.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To improve performance, this increases Rx descriptor to 256, Tx descriptor
to 64, and adjusts NAPI weight to NAPI_POLL_WEIGHT.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the wol state forces to be initialized after reset, the state should
be preserved in suspend/resume sequence.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If wol state of phy hardware is enabled after reset, phy_ethtool_get_wol()
returns that wol.wolopts is true.
However, since net_device.wol_enabled is zero and this doesn't apply wol
state until calling ethtool_set_wol(), so mdio_bus_phy_may_suspend()
returns true, that is, it's in a state where phy can suspend even though
wol state is enabled.
In this inconsistency, phy_suspend() returns -EBUSY, and at last,
suspend sequence fails with the following message:
dpm_run_callback(): mdio_bus_phy_suspend+0x0/0x58 returns -16
PM: Device 65000000.ethernet-ffffffff:01 failed to suspend: error -16
PM: Some devices failed to suspend, or early wake event detected
In order to fix the above issue, this patch forces to set initial wol state
to disabled as default.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces suspend and resume functions to ave driver.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few MAC/PHYs combinations which now support > 1Gbps. These
may need to make use of link modes with bits > 31. Thus their
supported PHY features or advertised features cannot be implemented
using the current bitmap in a u32. Convert to using a linkmode bitmap,
which can support all the currently devices link modes, and is future
proof as more modes are added.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to convert the local advertising to an LCL capabilities,
which is then used to resolve pause flow control settings.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver may sleep with holding a spinlock.
The function call paths (from bottom to top) in Linux-4.17 are:
[FUNC] usleep_range
drivers/net/ethernet/socionext/sni_ave.c, 892:
usleep_range in ave_rxfifo_reset
drivers/net/ethernet/socionext/sni_ave.c, 932:
ave_rxfifo_reset in ave_irq_handler
[FUNC] usleep_range
drivers/net/ethernet/socionext/sni_ave.c, 888:
usleep_range in ave_rxfifo_reset
drivers/net/ethernet/socionext/sni_ave.c, 932:
ave_rxfifo_reset in ave_irq_handler
To fix these bugs, usleep_range() is replaced with udelay().
These bugs are found by my static analysis tool DSAC.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool can be used to enable/disable pause. Add a helper to configure
the PHY when asym pause is supported.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have the MAC drivers manipulate phydev members to indicate
they support Asym Pause, add a helper function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many Ethernet MAC drivers want to limit the PHY to only advertise a
maximum speed of 100Mbs or 1Gbps. Rather than using a mask, make use
of the helper function phy_set_max_speed().
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for specifying system controller that configures
phy-mode setting.
According to the DT property "phy-mode", it's necessary to configure the
controller, which is used to choose the settings of the MAC suitable,
for example, mdio pin connections, internal clocks, and so on.
Supported phy-modes are SoC-dependent. The driver allows phy-mode to set
"internal" if the SoC has a built-in PHY, and {"mii", "rmii", "rgmii"}
if the SoC supports each mode. So we have to check whether the phy-mode
is valid or not.
This adds the following features for each SoC:
- check whether the SoC supports the specified phy-mode
- configure the controller accroding to phy-mode
The DT property accepts one argument to distinguish them for multiple MAC
instances.
ethernet@65000000 {
...
socionext,syscon-phy-mode = <&soc_glue 0>;
};
ethernet@65200000 {
...
socionext,syscon-phy-mode = <&soc_glue 1>;
};
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the link is becoming up for Pro4 SoC, the kernel is stalled
due to some missing clocks and resets.
The AVE block for Pro4 is connected to the GIO bus in the SoC.
Without its clock/reset, the access to the AVE register makes the
system stall.
In the same way, another MAC clock for Giga-bit Connection and
the PHY clock are also required for Pro4 to activate the Giga-bit feature
and to recognize the PHY.
To satisfy these requirements, this patch adds support for multiple clocks
and resets, and adds the clock-names and reset-names to the binding because
we need to distinguish clock/reset for the AVE main block and the others.
Also, make the resets a required property. Currently, "reset is
optional" relies on that the bootloader or firmware has deasserted
the reset before booting the kernel. Drivers should work without
such expectation.
Fixes: 4c270b55a5 ("net: ethernet: socionext: add AVE ethernet driver")
Suggested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a compatible string and SoC data for ethernet controller on
UniPhier PXs3 SoC.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables AVE_GI_RXDROP interrupt factor. This factor indicates
depletion of Rx descriptors and the handler counts the number
of dropped packets.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UniPhier platform from Socionext provides the AVE ethernet
controller that includes MAC and MDIO bus supporting RGMII/RMII
modes. The controller is named AVE.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kunihiko Hayashi