If wowlan if off mac80211 will stop / start the driver on suspend /
resume. This causes problems on resume since request_firmware is called
from start. Fix this by caching the nv.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On some wcnss firmwares the start command can take up to 300ms to
complete. Currently there is a 200ms timeout for SMD command to
complete which causes the start to fail.
Increase the timeout to 500ms. Also improve debug information
regarding SMD command completion time.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Response format is not in the canonical format.
wcn36xx_smd_rsp_status_check cannot be used.
* Save the FW caps in wcn36xx struct for later use.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TI wl12xx/wl18xx cards support channel switch via a driver specific
switch_channel op while operating with channel contexts.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enabling beacon filtering before receving a beacon
might result in not having a beacon at all for the
current connected AP, which prevents the station
from entering power-save.
Replace the current approach (of starting beacon
filtering on init) and configure beacon filering
only after bss_conf->dtimper is set (which means
mac80211 already parsed a beacon).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
dfs configuration command might take longer than
the current timeout. increase it to 5 seconds.
Signed-off-by: Yaniv Machani <yanivma@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Silently ignore repetitive scheduling of recovery work and commands
being passed to the bus when the HW is not available. This can happen
many times during recovery and slow it down. It also spams the kernel
logs.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Each AP has its own global and broadcast links, so when
checking for active sta count (according to the active_link_count)
we must take them all into account.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 unsets the default wep key on disassoc.
The fw doesn't support this notification, so simply
ignore it.
The actual flow actually triggers fw recovery in some
cases, as mac80211 unsets the default key only after
disassoc, when wlvif->sta.hlid, resulting in invalid
hlid being passed to the fw.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12xx chips allow only OFDM rates in AP mode for BT-Coex purposes. This
is no longer required in 18xx chips, starting with FW 8.6.0.0.8.
Update the min allowed FW version in 18xx to support this functionality.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stopping sched scan on interface removal (during recovery)
is no longer needed, as sched scanning is automatically
restarted by mac80211.
Signed-off-by: Barak Bercovitz <barak@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Send EAPOL frames with voice priority by setting (the new)
TX_HW_ATTR_EAPOL_FRAME bit in tx attribute.
Sending EAPOL with voice priority fixes re-key
timeout issues during heavy traffic.
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bump the min wl18xx fw version to 8.8.0.0.13
This fw is not backward compatible with older
firmware (due to api changes), so use bump
the firmware name as well.
Some modifications were done to the driver-fw api
in order to support multiple APs.
Additionally, some of the consts (such as max stations,
max links and max RX BA sessions) were changed.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Each hw supports a different iface combinations.
Define the supported combinations in each driver,
and save it in wl->iface_combinations.
Since each driver defines its own combinations now,
it can also define its max supported channels, so
we no longer need to save and set it explicitly
in wlcore.
Update wl18xx interface combinations to allow
multiple APs.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Each hw supports a different max stations (connected to the
same ap). add a new wl->max_ap_stations and use it instead
of the current common AP_MAX_STATIONS.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Upcoming fw versions will have different max links support
(according to the hw). Get ready for it by configuring
wl->num_links per-hw, instead of using the const WL12XX_MAX_LINKS.
However, continue using WLCORE_MAX_LINKS in order to simplify
structs declarations (we use it in multiple bitmaps, and converting
them to dynamic arrays is just cumbersome).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of splitting the fw_status into 2 and using some
complex calculations, read the fw status and let each low-level
driver (wl12xx/wl18xx) convert it into a common struct.
This is required for the upcoming fw api changes, which
break the current logic anyway.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It seems the wl18xx FW sometimes sends spurious changes on the PSM state
of the broadcast HLID. This causes us to search for a station on a
non-peer link and fail, causing warnings in our log.
Prevent the driver from considering PSM changes for any non-peer HLIDs.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the chip is in ELP mode read/write to FW is invalid and may cause
the lower layers to get stuck. The reads/writes concerning ELP wakeup
are the exception here and are checked for. In addition to blocking the
IO, produce a warning.
Signed-off-by: Barak Bercovitz <barak@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes a tx_flush during suspend fails, but the FW manages to flush
out the packets during the time when the host is supsended. Cancel
the Tx-watchdog on suspend to not cause a spurious recovery on resume
for that case. Set a flag to reinit the watchdog on the first Tx after
resume, so we'll still recover if the FW is not empty and there's
indeed a problem.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
zero rx_filter_enabled array after recovery to avoid
cases were the driver will keep trying to clear a
filter which is not configured in FW.
Such case will cause consecutive recoveries due to
command execution failures.
While on it, convert rx_filter_enabled to bitmap,
to save some memory and make sparse happy (it
doesn't like sizeof(bool array)).
Signed-off-by: Nadim Zubidat <nadimz@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use ieee80211_channel_to_frequency() to replace b43_channel_to_freq_{2,5}ghz(),
and remove unused b43_freq_to_channel_{2,5}ghz().
Signed-off-by: ZHAO Gang <gamerh2o@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
remove_proc_subtree() doesn't work here as local->ddev has already
been removed, and NULLed out. Use proc_remove() instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes regression caused by commit a16dad7763 "MIPS: Fix
potencial corruption". That commit fixes one corruption scenario in
cost of adding another one, which actually start to cause crashes
on Yeeloong laptop when rtl8187 driver is used.
For correct DMA read operation on machines without DMA coherence, kernel
have to invalidate cache, such it will refill later with new data that
device wrote to memory, when that data is needed to process. We can only
invalidate full cache line. Hence when cache line includes both dma
buffer and some other data (written in cache, but not yet in main
memory), the other data can not hit memory due to invalidation. That
happen on rtl8187 where struct rtl8187_priv fields are located just
before and after small buffers that are passed to USB layer and DMA
is performed on them.
To fix the problem we align buffers and reserve space after them to make
them match cache line.
This patch does not resolve all possible MIPS problems entirely, for
that we have to assure that we always map cache aligned buffers for DMA,
what can be complex or even not possible. But patch fixes visible and
reproducible regression and seems other possible corruptions do not
happen in practice, since Yeeloong laptop works stable without rtl8187
driver.
Bug report:
https://bugzilla.kernel.org/show_bug.cgi?id=54391
Reported-by: Petr Pisar <petr.pisar@atlas.cz>
Bisected-by: Tom Li <biergaizi2009@gmail.com>
Reported-and-tested-by: Tom Li <biergaizi2009@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Larry Finger <Larry.Finger@lwfinger.next>
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the original code we shift "AR5K_PHY(256) >> 28" which is zero but
the intent was to shift the return value of ath5k_hw_reg_read() like we
do a couple lines later.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rtl_ps_enable_nic() is called from loops that will loop until this function returns true or a
maximum number of retries is performed.
hw_init() returns non-zero on error. In that situation return false to
restore the original design intent to retry hw init when it fails.
Signed-off-by: Olivier Langlois <olivier@trillion01.com>
Cc: Stable <stable@vger.kernel.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rtl8192ce is disabling for too long the local interrupts during hw initiatialisation when performing scans
The observable symptoms in dmesg can be:
- underruns from ALSA playback
- clock freezes (tstamps do not change for several dmesg entries until irqs are finaly reenabled):
[ 250.817669] rtlwifi:rtl_op_config():<0-0-0> 0x100
[ 250.817685] rtl8192ce:_rtl92ce_phy_set_rf_power_state():<0-1-0> IPS Set eRf nic enable
[ 250.817732] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.817796] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.817910] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818024] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818139] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818253] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818367] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818472] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818472] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818472] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818472] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818472] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:98053f15:10
[ 250.818472] rtl8192ce:rtl92ce_sw_led_on():<0-1-0> LedAddr:4E ledpin=1
[ 250.818472] rtl8192c_common:rtl92c_download_fw():<0-1-0> Firmware Version(49), Signature(0x88c1),Size(32)
[ 250.818472] rtl8192ce:rtl92ce_enable_hw_security_config():<0-1-0> PairwiseEncAlgorithm = 0 GroupEncAlgorithm = 0
[ 250.818472] rtl8192ce:rtl92ce_enable_hw_security_config():<0-1-0> The SECR-value cc
[ 250.818472] rtl8192c_common:rtl92c_dm_check_txpower_tracking_thermal_meter():<0-1-0> Schedule TxPowerTracking direct call!!
[ 250.818472] rtl8192c_common:rtl92c_dm_txpower_tracking_callback_thermalmeter():<0-1-0> rtl92c_dm_txpower_tracking_callback_thermalmeter
[ 250.818472] rtl8192c_common:rtl92c_dm_txpower_tracking_callback_thermalmeter():<0-1-0> Readback Thermal Meter = 0xe pre thermal meter 0xf eeprom_thermalmeter 0xf
[ 250.818472] rtl8192c_common:rtl92c_dm_txpower_tracking_callback_thermalmeter():<0-1-0> Initial pathA ele_d reg0xc80 = 0x40000000, ofdm_index=0xc
[ 250.818472] rtl8192c_common:rtl92c_dm_txpower_tracking_callback_thermalmeter():<0-1-0> Initial reg0xa24 = 0x90e1317, cck_index=0xc, ch14 0
[ 250.818472] rtl8192c_common:rtl92c_dm_txpower_tracking_callback_thermalmeter():<0-1-0> Readback Thermal Meter = 0xe pre thermal meter 0xf eeprom_thermalmeter 0xf delta 0x1 delta_lck 0x0 delta_iqk 0x0
[ 250.818472] rtl8192c_common:rtl92c_dm_txpower_tracking_callback_thermalmeter():<0-1-0> <===
[ 250.818472] rtl8192c_common:rtl92c_dm_initialize_txpower_tracking_thermalmeter():<0-1-0> pMgntInfo->txpower_tracking = 1
[ 250.818472] rtl8192ce:rtl92ce_led_control():<0-1-0> ledaction 3
[ 250.818472] rtl8192ce:rtl92ce_sw_led_on():<0-1-0> LedAddr:4E ledpin=1
[ 250.818472] rtlwifi:rtl_ips_nic_on():<0-1-0> before spin_unlock_irqrestore
[ 251.154656] PCM: Lost interrupts? [Q]-0 (stream=0, delta=15903, new_hw_ptr=293408, old_hw_ptr=277505)
The exact code flow that causes that is:
1. wpa_supplicant send a start_scan request to the nl80211 driver
2. mac80211 module call rtl_op_config with IEEE80211_CONF_CHANGE_IDLE
3. rtl_ips_nic_on is called which disable local irqs
4. rtl92c_phy_set_rf_power_state() is called
5. rtl_ps_enable_nic() is called and hw_init()is executed and then the interrupts on the device are enabled
A good solution could be to refactor the code to avoid calling rtl92ce_hw_init() with the irqs disabled
but a quick and dirty solution that has proven to work is
to reenable the irqs during the function rtl92ce_hw_init().
I think that it is safe doing so since the device interrupt will only be enabled after the init function succeed.
Signed-off-by: Olivier Langlois <olivier@trillion01.com>
Cc: Stable <stable@vger.kernel.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As result deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case IRQ configuration is unknown possibly enabled MSIs
are left enabled in ath10k_pci_deinit_irq(). This update
fixes the described misbehaviour.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The documentation states that pci_enable_msi_block() returns the number of
requests 'could have been allocated', not 'could allocate'. IOW, MSIs are *not*
enabled if a positive value returned.
kvalo: add commit log based on Alexander's email
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pass frames with invalid peer status to upper layer.
Next mac80211 will validate frames and drop if required.
This is required to detect spurious frames and pass
this info to user mode (detect CLASS2 CLASS3 frames from
nonauthenticated/nonassociated stations).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is a workaround for HT-enabled STAs which break the spec
and have no HT capabilities RX mask (no HT RX MCS map).
As per spec, in section 20.3.5 Modulation and coding scheme (MCS),
MCS 0 through 7 are mandatory in 20MHz with 800 ns GI at all STAs.
Firmware asserts if such situation occurs.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case of warm reset target need to be suspended.
Suspend function is extented to handle both cases
with disabling interrupts and without disabling interrupts.
Warm target reset requires suspend with all interrupts
disabled.
This patch depends on
ath10k: fix device initialization routine
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Suspend/resume callbacks are not protected by configuration mutex
so adding such protection. Also in order to simplify implemetation
of suspend function wait queue is replaced by completion.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Hardware CUS232 version 2 has some issues with cold
reset that lead to Data Bus Errors or system hangs
in some cases. It's safer to use warm reset when
possible as it shouldn't trigger the
aforementioned issues.
Prefer warm reset over cold reset. However since
warm reset doesn't work after FW crash make sure to
fallback to cold reset when booting up the HW.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was found during testing the nss calculation does not
cover all corner cases. Station could request eq. only MCS8
and MCS9 (nss=2 specific). Next num_rates=2 so the driver
sets nss=(max((2+7)/8, 1))=1. Which is wrong. The in-driver
calculation was introduced prior (commit ddcc347b70
mac80211: fix rx_nss calculation for drivers with hw rc).
Since it's fixed, use mac80211 provided value from now.
End user will experience lower throuhputs than expected
if the nss is wrongly calculated.
Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This throw a lot of pointless warnings in case of DFS (radar
detection) and PHYERR events from firmware, when firmware may
actually insert more data, than we assume.
Besides of being noisy this debug does not protect or check
anything usefull currently. It was introduced long time ago
while debugging aggregations. So just removing it.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Show message length and expected length. Helps debug
firmware mismatch issues.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
NICs supported by iwldvm don't handle well TX AMPDU.
Disable it by default, still leave the possibility to
the user to force enable it with a debug parameter.
NICs supported by iwlmvm don't suffer from the same issue,
leave TX AMPDU enabled by default for these.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The new API for ALIVE notification was misunderstood.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
These inlines are pretty pointless now as they just return a
fixed struct value, remove them - the code even gets shorter.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Support the changes below:
- Fields and sections structure were changed.
- the NVM file built from DWord instead of Words.
- sections header format was changed.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
New FW enables support for power save on BSS and P2P client MACs
simultaneously when they function on different channels (DCM).
Enable this case in the driver after examining new TLV flag -
IWL_UCODE_TLV_FLAGS_BSS_P2P_PS_DCM. Still power management is not
allowed on both MACs if they function on a same channel.
Remove another redundant TLV flag - IWL_UCODE_TLV_FLAGS_P2P_PS that
is not in use anymore. Remove bound_vif_cnt as redundant.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Allow reading/writing prph registers.
The address is set in the first argument
of the write operation. second argument
is optional and can be used for writing.
e.g.
echo '0xA01234 0x99' > /sys/kernel/debug/ieee80211/phy0/iwlwifi/iwlmvm/prph_reg
will write 0x99 into reg 0xA01234
cat /sys/kernel/debug/ieee80211/phy0/iwlwifi/iwlmvm/prph_reg
will show its current value (probably 0x99)
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Instead of checking the SKB protocol against EAP, check the
IEEE80211_TX_CTRL_PORT_CTRL_PROTO flag that more generally
indicates whether or not the frame is a port control frame.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This will allow to get sniffer captures with correct
settings for these HT / VHT capabilities.
Also set the corresponding HAVE_MCS / VHT_KNOWN bits in
the registration to mac80211.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There are a number of things in the .data section that should
really be in .rodata, for example all ops structs and strings.
Mark everything const that can be, leaving the .data section
pretty much empty.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The various code blocks in iwl_pcie_[rt]xq_inc_wr_ptr
finally do the same things, so just merge them
all and make the functions cleaner.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This patch adds key material V2 support to mwifiex.
Newer FW supports this feature and FW KEY API version is used
to determine which command structure needs to be used.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support to parse FW API version TLVs.
Currently only API version for key_material is supported.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During deauthenticate/link lost event, disable all TDLS links as
TDLS would not work when infra connection is not active.
Also this will avoid an issue where ping to peer station doesn't
work after reassociation to AP where we had created TDLS link in
earlier association.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If TDLS link is 11ac enabled i.e. we as well as peer station
supports VHT, configure seprate TX & RX window sizes during
BA setup. So even if BSS does not support 11ac, we can use VHT
capabilities and higher window sizes on direct link.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During TDLS setup request/response, if HW is 11ac capable,
we add VHT Capability IEs in outgoing data frame. Also while
processing received setup request/response, we preserve peer's
11ac capability retrieved from IEs.
Patch also gets VHT parameters from config_station handlers and
sets it to FW using TDLS config command.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch changes mwifiex_fill_vht_cap_tlv function to pass
struct ieee80211_vht_cap instead of mwifiex_ie_types_vhtcap
so that it can be used generically.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds AMPDU support for TDLS link. We have set 11n
capabilities including AMPDU parameters during ENABLE_LINK.
We set a variable in RA list to indicate this as TDLS link.
This patch uses these capabilities to know if AMPDU is allowed
on TDLS link and enables AMPDU aggregation for TX and RX reording
support for RA list for this peer.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1. If data packet is addressed to TDLS peer for which link is
established, mark these packets with TDLS flag so that FW can
send them on direct link instead of sending via AP.
2. If data packet is addressed to TDLS peer and TDLS setup is
underway, move these packets to TDLS queue.
3. If this packet is TDLS setup packet, do not block it.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While TDLS link is being setup, few packets from this station to
peer station may be buffered at AP. It may happen that once TDLS
link is setup, packets sent from station to peer on direct link
get delivered before traffic from AP arrives at peer station.
This results into packet reordering issue at peer station.
To avoid this, we hold data packets destined to TDLS peer during
TDLS setup. These packets are moved to temperory TDLS TX queue.
Upon successful TDLS setup, they are moved to RA list created for
this peer. Upon failure, packets are moved back to AP's RA list
for that particular TID.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds cfg80211 change_station handler support for mwifiex
which is needed for TDLS link setup. Driver creates a command to
modify peer link capabilities and issues command to FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds cfg80211 add_station handler support for mwifiex
which is needed for TDLS setup. Driver issues create TDLS link
command to FW upon receiving add_station from cfg80211.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds cfg80211 handler tdls_oper handler support to
mwifiex. Upon enable link, driver sets status as TDLS status as
setup complete and also sets AMSDU size, AMPDU params for direct
link. Upon disable link, driver issues command to FW to delete
this link in FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for parsing TDLS action frames during
station receive handler.
Peer station capabilities are stored into station node.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for TDLS management frames transmit
handler. mwifiex driver supports TDLS with external support,
i.e. expects user space application to form TDLS frames.
Same is advertised to cfg80211 during registration.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pass 'struct ieee80211_ht_cap' pointer to
mwifiex_fill_cap_info() instead of
'struct mwifiex_ie_types_htcap' pointer, because the routine
internally uses the later one.
This patch also adds WARN_ON_ONCE check for NULL band.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These functions are now needed by TDLS while managing station list.
Move them from AP related file to utility file.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
tos_to_tid_inv values are needed even during TDLS restore
operations. Currently tos_to_tid_inv is part of wmm.c and
is declared static.
Make it part of private structure so that it can be used in
other files as well.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug where we were checking for AP's AMPDU param
setting even when transmitting traffic to associated station.
Patch adds provision to pass additional parameter ra_list pointer
to function which checks if AMPDU is allowed. If current BSS type is
AP, we check station's AMPDU params else we check AP's AMPDU params.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently MU/SU beamformer and MU beamformee features are
not supported.
Hence this patch modifies VHT capability information accordingly.
Number of sounding dimensions should be zero in this case.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes sure that beamforming capability field in
ht capability info gets filled if hardware supports the feature.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current mwifiex pcie driver assumed that it would get
its cmdrsp_complete() callback called before another command
was sent to unmap the command's skbuff. However, that is not
true. The mwifiex_check_ps_cond() will send a sleep command
to the card without having adapter->curr_cmd set. Within the
workqueue's state machine the adapter's state would be set
to allow commands (curr_cmd = NULL && cmd_sent = false) after
having receieved the response from the sleep command. The
card->cmd_buf would then be overridden with the new command
but the first command's skbuff was not unmapped. This leaks
mapped skbuffs when a bounce buffer is employed.
To rectify this unmap the card->cmd_buf when the response is
received from the card instead of waiting for the
cmdrsp_complete() callback.
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Stewart <pstew@chromium.org>
Reviewed-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Depending on the underlying DMA implementation its
not possible to partially unmap DMA buffers. Moreover
its not possible to understand the intent of passing
0 as the size to dma unmap. The intent of this
driver is unmap the entire skb buffer. The only way
to ensure that the size matches on unmap is to store
both the dma address and the size in the skb ca field.
Introduce a mwifiex_dma_mapping structure which tracks
the dma address and the size. Additionally, provide
a mwifiex_unmap_pci_memory() that utilizes the new
structure. This also provide symmetry within the
internal API.
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Stewart <pstew@chromium.org>
Reviewed-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In extended scan, host gets scan results through one or
multiple events instead of scan command response. Host will
send next scan command when all the events are received.
Legacy scan sometimes truncates scan results in a noisy
environment due to buffer length limitation. This issue
is addressed in extended scan.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This new function will be useful later for extended scan
feature.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This new function will be useful later for extended scan
feature.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
'mwifiex_bcn_param' structure contains five parameters which
are present in beacon buffer in case of legacy scan.
'rssi' field won't be there in this buffer for extended scan.
Hence 'bssid' and 'rssi' are removed from the structure and it is
renamed as 'mwifiex_fixed_bcn_param' so that we can have common
parsing logic later for both.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bit12 in fw_cap_info is for testing only.
Remove all related code.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1) rename max_mcs to mcs;
2) initialize 'i' and 'nss' as 1 instead of 0 in nss lookup;
3) use GET_VHTNSSMCS(mcs_map, nss) macro;
4) use IEEE80211_VHT_MCS_* definitions instead of hard coding
Reported-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove these local array variables and define them as static
const array in global space.
The duplicated mcs_rate table is removed automatically with this
change.
Reported-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove driver's macro and use ieee80211's definition instead
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a routine to calculate the median IQ correction
values for AR955x, which is used for outlier detection.
The normal method which is used for all other chips is
bypassed for AR955x.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will be used for storing data for mutiple
IQ calibration runs, for AR955x.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IQ calibration post-processing for AR955x is different
from other chips - instead of just doing it as part
of AGC calibration once, it is triggered 3 times and
a median is determined. This patch adds initial support
for changing the calibration behavior for AR955x.
Also, to simplify things, a helper routine to issue/poll
AGC calibration is used.
For non-AR955x chips, the iqcal_idx (which will be used
in subsequent patches) is set to zero.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Incorrect values are programmed in the registers
containing the IQ correction coefficients by the IQ-CAL
post-processing code. Fix this.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use ar9003_hw_tx_iq_cal_outlier_detection instead.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In chips like AR955x, the initvals contain the information
whether IQ calibration is to be done in the HW when an
AGC calibration is triggered. Check if IQ-CAL is enabled
in the initvals before flagging 'txiqcal_done' as true.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calibration data is not reused for SoC chips, so
call ar9003_hw_tx_iq_cal_post_proc() with the correct
argument. The 'is_reusable' flag is currently used
only for PC-OEM chips, but it makes things clearer to
specify it explicity.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Buffalo WLI-UV-AG300P is almost the same as Sony UWA-BR100.
Signed-off-by: Masaki TAGAWA <masaki@club.kyutech.ac.jp>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no benefit in retaining the legacy rate control module
in the driver codebase.
It is known to be buggy and has less than optimal performance
in real-world environments compared with minstrel. The only
reason that it was kept when we made the switch to minstrel
as default was that it showed higher throughput numbers in a
clean/ideal environment.
This is no longer the case and minstrel can push ath9k to
the same throughput levels. In TCP, with 3-stream cards, more than
295 Mbps can be obtained in open air, with 2-stream cards,
210 Mbps is easily reached. To test performance issues,
instead of using a broken rate control module, it is better
to use the fixed-rate interface provided by mac80211 anyway.
The ath9k RC has not received any bug fixes in years and is
just bit-rotting away - this patch removes it.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
after switch to common fucntions we do not need this memcpy any more.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
and rename it to ath9k_cmn_rx_skb_postprocess. We will use it
on ath9k_htc.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we can reuse this function in ath9k_htc
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we can reuse this fucntion on ath9k_htc.
Now we will need to use common version last_rssi, so switch
it too.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we need access to this variable from common functions.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On commit 28f2bce9f8 I make change that
print various messages as default. This can cause flood of messages
related to TX status timeout on some environments. I partially fixed
problem on commit bb9c298f31, but forgot
to move two more messages to debug level.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the enter and exit download sequence the chip core info was checked
for presence of CM3 ARM core. If found it would enter download state for
the CM3. However, on devices that have a CM3 and CR4 this is not correct
and the CR4 should be used to enter download state. This patch changes
the ARM core lookup giving CR4 precedence.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The brcmf_add_keyext() is for setting per-station key for cipher
algorithms such as WPA1/WPA2 and should not be used to set
WEP broadcast/unicast keys. This patch fixes connect failure
problem with AP using 802.1x-WEP.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Daniel Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of instantiating core info structs based upon the
chip identifier it is now done parsing information provided
on the device.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In brcmf_contstruct_reginfo() some error logging was added by:
commit f7c51a1a72f50870f80001ddf528a6f7f992bc16
Author: Arend van Spriel <arend@broadcom.com>
Date: Wed Dec 11 16:21:21 2013 +0100
brcmfmac: correct reporting HT40 support in wiphy htcap
This logging was not intended to be delivered and adds a lot
of messages in the log. The patch removes this logging statement.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function brcmf_sdio_bus_sleep() function is called rather
frequently, which fills the log when TRACE level is enabled. Reduced
the level to SDIO.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch make several chip related functions host interface
independent by defining callback interface struct brcmf_buscore_ops.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the function sdio_remove will first destroy the datawork
workqueue and then detach the bus. This can create the situation
where work gets added on non-existing work queue resulting in panic.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmf_sdio_download_code_file is using a loop to send small blobs
of data. This is unnecessarily complex and was simplified with this
patch.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
the function brcmf_sdiod_ramrw is supposed to be able to send
large blobs of data. However inside the loop the skb->len field
did not correctly get reset each round. As a result only small
blobs could be sent. This patch fixes this problem.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just renaming the file. This file will contain chip related functions
that are independent of the host interface type.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The chip related functions will be made agnostic of the host
interface. However, some functions in the source file are
rather SDIO specific so better move it to the SDIO specific
source file.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Address of rte console was not initialized and so console logging
functionality didn't kick in. This patch fixes it and makes console
polling interval a debugfs variable.
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Daniel Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To link module attribute with sdio device driver attribute in sysfs.
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Expand the get_station command to also report dtim period and
beacon interval when the device is connected.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/ath/ath9k/main.c: In function ‘ath9k_has_tx_pending’:
drivers/net/wireless/ath/ath9k/main.c:1869: warning: ‘npend’ may be used uninitialized in this function
Introduced by commit 10e2318103 ("ath9k:
optimize ath9k_flush").
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In rtl8180/rtl8187 drivers, few register bit definitions have
names of form FOOBAR_SHIFT, suggesting they should be used as
shift offset, for example
reg |= (1 << ENABLE_FOO_SHIFT).
However they are actually defined as (1 << x) and thus they are
used (correctly) like
reg |= ENABLE_FOO_SHIFT;
This patch kills the misleading _SHIFT suffix.
Signed-off-by: andrea merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: Fix IQ calibration" added a check
to ensure that valid i2_p_q2_a0_d1 values are not discarded.
But since it is masked with 0xfff earlier, the codepath
will not be executed.
The earlier case where all values above 0x800 were considered
invalid is incorrect, since the HW can return valid values
between 0x800 and 0xfff.
Cc: Kai Shi <kaishi@qca.qualcomm.com>
Reported-by: Alex Hacker <hacker@epn.ru>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Soon mac80211 will support multi-interface CSA so
using sc->csa_vif is not an option.
Instead just depend on vif->csa_active. Calling
ieee80211_csa_finish() multiple number of times
should not be an issue.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new HWSIM_ATTR_USE_CHANCTX attribute to the
HWSIM_CMD_CREATE_RADIO command to allow the creation of radios with
one channel that use channel contexts. If this attribute is not
present, the behaviour is the same as before (ie. single channel
radios don't use channel contexts and multi channel radios do).
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's little point in setting the number of channels if the
entire combination struct is overwritten again later - that
was clearly intended the other way around, fix it.
Reported-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Orignal code will not detect a DMA mapping failure, causing the HW
to attempt a DMA from an invalid address.
This patch add the error check and eventually simply drops the TX
packet if we can't map it for DMA.
Signed-off-by: andrea merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In original code the old RX DMA buffer is unmapped and processed and at the end
of the isr a new buffer is mapped with pci_map_single and attached to the RX
descriptor.
If pci_map_single fails then the RX descriptor remains with no valid DMA buffer
attached.
In this condition the DMA will target where it shouldn't with obvious evil
consequences.
Simply avoiding re-arming the descriptor will prevent buggy DMA but it will
result soon in RX stuck.
This patch move the DMA mapping of the new buffer at the beginning of the ISR
(and it adds error check for pci_map_single success/fail).
If the DMA mapping fails then we do not unmap the old buffer and we re-arm the
descriptor without processing it, with the old DMA buffer still attached.
In this way we lose the currently RX-ed packet, but whenever next calls to
pci_map_single will succeed again,then the RX process will go on without stuck.
Signed-off-by: andrea merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The number of the PAPD group was increased in new devices.
Since we might now get empty entries on older devices, don't
warn if an entry is empty.
Signed-off-by: Ariej Marjieh <ariej.marjieh@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Alive notification ver2 support error table information
for 2 CPUs.
This is useful to fetch the error information in case of
firmware assert.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The 8000 family includes devices that don't support 11ac.
Add an iwl_cfg structure for them.
Signed-off-by: Ariej Marjieh <ariej.marjieh@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Newer NIC have different memory layout in their SRAM,
so change the checks in iwl_mvm_dump_nic_error_log
accordingly.
Signed-off-by: Ariej Marjieh <ariej.marjieh@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
For TSF master/slave synchronization, the FW does not require
exact match in the beacon interval between the master interface
and the slave one, but instead requires that the beacon interval
of one interface is the module of the other.
Modify the tsf_id selection to align with the above.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The d3/d0i3 fw code requires the sta_id to be 0
(this is used to determine the rates and keys
to use in arp offloading).
Reserve sta_id 0 to station interface in order
to comply with this requirement.
Change some functions prototypes in order to
make the allocation function know about
the interface type.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The current WARNING isn't very helpful.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
ieee80211_rx_status.flags is full. Define a new vht_flag
variable to be able to set more VHT related flags and make
room in flags.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com> [ath10k]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The purpose of this housekeeping is to make some room for
VHT flags. The radiotap vendor fields weren't in use.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When receiving an IBSS_JOINED event select the BSS object
based on the {bssid, channel} couple rather than the bssid
only.
With the current approach if another cell having the same
BSSID (but using a different channel) exists then cfg80211
picks up the wrong BSS object.
The result is a mismatching channel configuration between
cfg80211 and the driver, that can lead to any sort of
problem.
The issue can be triggered by having an IBSS sitting on
given channel and then asking the driver to create a new
cell using the same BSSID but with a different frequency.
By passing the channel to cfg80211_get_bss() we can solve
this ambiguity and retrieve/create the correct BSS object.
All the users of cfg80211_ibss_joined() have been changed
accordingly.
Moreover WARN when cfg80211_ibss_joined() gets a NULL
channel as argument and remove a bogus call of the same
function in ath6kl (it does not make sense to call
cfg80211_ibss_joined() with a zero BSSID on ibss-leave).
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: Bing Zhao <bzhao@marvell.com>
Cc: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Cc: libertas-dev@lists.infradead.org
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
[minor code cleanup in ath6kl]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The scheduled scan matchsets were intended to be a list of filters,
with the found BSS having to pass at least one of them to be passed
to the host. When the RSSI attribute was added, however, this was
broken and currently wpa_supplicant adds that attribute in its own
matchset; however, it doesn't intend that to mean that anything
that passes the RSSI filter should be passed to the host, instead
it wants it to mean that everything needs to also have higher RSSI.
This is semantically problematic because we have a list of filters
like [ SSID1, SSID2, SSID3, RSSI ] with no real indication which
one should be OR'ed and which one AND'ed.
To fix this, move the RSSI filter attribute into each matchset. As
we need to stay backward compatible, treat a matchset with only the
RSSI attribute as a "default RSSI filter" for all other matchsets,
but only if there are other matchsets (an RSSI-only matchset by
itself is still desirable.)
To make driver implementation easier, keep a global min_rssi_thold
for the entire request as well. The only affected driver is ath6kl.
I found this when I looked into the code after Raja Mani submitted
a patch fixing the n_match_sets calculation to disregard the RSSI,
but that patch didn't address the semantic issue.
Reported-by: Raja Mani <rmani@qti.qualcomm.com>
Acked-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A few places weren't checking that the frame passed to the
function actually has enough data even though the function
clearly documents it must have a payload byte. Make this
safer by changing the function to take an skb and checking
the length inside. The old version is preserved for now as
the rtl* drivers use it and don't have a correct skb.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Advertise to mac80211 that we can do channel switch both
for STA and AP/GO.
After each beacon transmission check if CSA is done and
call ieee80211_csa_finish if needed.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When creating new devices, allow P2P-Device support to be
turned off to be able to test default behaviour with and
without the support.
Also add a module parameter for the default setting.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's not a single rate control algorithm actually in
a separate module where the module refcount would be
required. Similarly, there's no specific rate control
module.
Therefore, all the module handling code in rate control
is really just dead code, so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change the code to allow making all the rate control ops
const, nothing ever needs to change them. Also change all
drivers to make use of this and mark the ops const.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This required liberally sprinkling 'const' over brcmfmac
and mwifiex but seems like a useful thing to do since the
pointer can't really be written.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Addition of the frequency hints showed up couple of places in cfg80211
where pointers could be marked const and a shared function could be used
to fetch a valid channel.
Signed-off-by: Jouni Malinen <j@w1.fi>
[fix mwifiex]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The commit, "ath9k_hw: Fix incorrect Tx control power in AR9003 template"
fixed the incorrect values in the eeprom templates, but if
boards have already been calibrated with incorrect values,
they would still be using the wrong TX power. Fix this by assigning
a default value in such cases.
Cc: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Even though we make sure PowerSave is not enabled by default
by disabling the flag, WIPHY_FLAG_PS_ON_BY_DEFAULT on init,
PS could be enabled by userspace based on various factors
like battery usage etc. Since PS in ath9k is just broken
and has been untested for years, remove support for it, but
allow a user to explicitly enable it using a module parameter.
Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 ->sta_rc_update() callback must be atomic. Since we have to
take mutex and do other operations that can sleep when sending fimrware
commands to device, the only option to satisfy atomicity requirement of
->sta_rc_update(), that I can see, is introduce work_struct and defer
uploading new rates to that work.
Tested-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Raw id and FW id should be switched.
Tested-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is a copy/paste of patch provided by Sujith for ath9k.
"Even though we make sure PowerSave is not enabled by default
by disabling the flag, WIPHY_FLAG_PS_ON_BY_DEFAULT on init,
PS could be enabled by userspace based on various factors
like battery usage etc. Since PS in ath9k is just broken
and has been untested for years, remove support for it, but
allow a user to explicitly enable it using a module parameter."
Cc: stable@vger.kernel.org
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is know that PS cause issues on that old devices, disable it by
default.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have disabled it currently on other buses. PS can cause some issues,
not necessarily with our driver but on AP, that are not easy to debug.
Since behaviour differs on rt2800usb and rt2800pci, user usually blame
for malfunction rt2800usb driver, whereas issue is on AP side.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sta_rc_update() callback must be atomic, hence we can not take mutexes
or do other operations, which can sleep in ath9k_htc_sta_rc_update().
I think we can just return from ath9k_htc_sta_rc_update(), if it is
called without IEEE80211_RC_SUPP_RATES_CHANGED bit. That will help
with scheduling while atomic bug for most cases (except mesh and IBSS
modes).
For mesh and IBSS I do not see other solution like creating additional
workqueue, because sending firmware command require us to sleep, but
this can be done in additional patch.
Patch partially fixes bug:
https://bugzilla.redhat.com/show_bug.cgi?id=990955
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Aids in understanding excactly what a firmware is
offering.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The main complexity of the power code is that it needs to
take into account the firmware limitations.
These limitations state that we need to have a global
picture of the vifs present in the system to be able to
decide if we can enable power management on a specific vif.
Even device power save (as opposed to vif power management)
must be disabled in certain circumstances (monitor vif).
Refactor the current code to make this clearer by defining
a function that explicitely computes these constraints.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If the driver detects old firmware, we disable support for
power management.
This greatly simplifies the code.
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Instead of re-building the power command upon debugfs read,
store the latest command sent to the firmware.
This reduces the code complexity by reducing the number of
entries in the power code.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The firmware doesn't allow per-vif beacon filtering: we can
use beacon filtering for one vif only. So remember which
vif has beacon filtering enabled in the iterator, and send
the command outside the iterator.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reduce indentation where it is possible.
Make a function static - it wasn't used outside its file
anyway.
Remove the unneeded pm_prevent state.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Remove the enum abuse (using an enum to store a set of values),
the unneeded ret variable and unnecessary if nesting.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The Sync to SCO is a feature that allows to synchronize
between the WiFi traffic and the expectable BT traffic
when SCO profile is active.
We need to set the validity bit in the command in the init
flow, and set / clear the enablement bit if we want to
enabled / disable the feature.
While at it, clean up the flags that are not used in the
API.
This feature needs to be enabled / disabled easily, so
export its enablement to constants.h.
Reviewed-by: Eyal Zolotov <eyal.zolotov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Some older versions of wpa_supplicant don't necessarily stop
scheduled scan before starting a regular scan, and there's
nothing in the API that requires it either. As a consequence
our driver's behaviour of not allowing scan while scheduled
scan was in progress broke userspace.
However, it is valid to unilaterally stop scheduled scan at
any point in time, so when a regular scan request comes just
abort the scheduled scan and run the regular scan.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fix a potential buffer overrun when creating the fw name
in drv->firmware_name by setting a maximal length to the
char array copied to it.
The maximal length is also updated to 32 rather than 25 to
keep both 32bit and 64bit alignment without requiring
padding to the struct it is in.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Newer devices have two embedded CPUs, and the firwmare for
both of them is include in the .ucode file requested upon
enumeration.
An empty section with address=0xFFFFCCCC separates between
the sections intended for cpu1 and the sections intended
for cpu2.
Update the driver to parse the .ucode file with this format
and act accordingly.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In iwl_mvm_calc_rssi() some values are calculated but then
never used, remove the calculations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Support taking an mvm ref (and preventing D0i3) by
writing '1' into the d0i3_refs debugfs file.
The reference can be unref by writing 0 to the same
file.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Schedule work to query the wakeup reasons, and
disconnect in some cases (e.g. beacon loss).
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We need to ask the fw to wake up on incoming packets (that
pass the filters).
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add d0i3_refs debugfs file that prints the currently taken
mvm D0i3 refs.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We don't want to go into D0i3, when P2P_CLI, AP (including
GO) or IBSS interfaces are running, so take appropriate
references.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Take a reference when ROC command is started, and
unref it on completion.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Take a reference when starting to scan and release it on completion.
Note that if the scan is cancelled/aborted, a completion will still be
sent up.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Hold a bitmap of taken references, according to the
reference reason (e.g. down, scan).
This will allow us validate our state and add some debugfs
entries later on.
Unref the transport when the FW is fully initialized,
allowing it to go into a low power mode.
Disallow the transition to low-power while recovery is in
progress.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Upon D0i3 entry/exit, iterate over the active interfaces
and configure them appropriately.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Configure skip-over-dtim and beacon filtering on D0i3
enter/exit.
Since the D0i3 entry/exit commands require different
command flags (e.g. CMD_HIGH_PRIORITY), add a new parameter
to the functions being called, and make the current users
pass CMD_SYNC.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When the bus is in D0i3, we can't send regular commands to
the firmware. This means that we need to add a state to
remember what is our d0i3 state and make sure that only
d0i3 exit commands can be sent.
Add flags to CMD_ flags and transport status for this
purpose.
Commands with CMD_HIGH_PRIO set are queued at the head of
the command queue, behind other high priority commands.
Commands with CMD_SEND_IN_IDLE set can be sent while the
transport is idle (without taking rpm reference).
Commands with CMD_MAKE_TRANS_IDLE set indicate that command
completion should mark the transport as idle (and release
the bus).
Commands with CMD_WAKE_UP_TRANS set instruct the transport
to exit from idle when this command is completed.
The transport is marked as idle (STATUS_TRANS_IDLE) when
the FW enters D0i3 state. This bit is cleared when it
enters D0 state again.
Process only commands with CMD_SEND_IN_IDLE flag while the
transport is idle. Other enqueued commands will be
processed only later, right after exiting D0i3.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add new enter_d0i3 and exit_d0i3 ops that
will be called by the transport on D0i3 enter/exit.
Each one of these ops will include the host commands
mentionned in the previous patch.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
D0i3 is bus power saving feature. It involves the
firmware - the driver needs to send a list of commands
to the firmware before entering this state. Wake up from
d0i3 also requires a few commands to the firmware.
The trigger to enter D0i3 is an idle timeout that will be
implemented later and will most probably rely on RUNTIME_PM
infrastructure.
In order to prevent entrance to D0i3 in critical flows, we
implement here a reference infrastructure. When a ref is
taken, we can't enter D0i3.
PCIe does't support D0i3.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The tx backoff settings used by the thermal throttling mechanism can
also be used for enforcing a limit on the power consumption of the module.
Handle the platform PCIe power limitation by translating the limit
(measured in mw) to its respective tx backoff value. The translation is
module specific.
The resulting tx backoff value is sent to the ucode, and also serves as the
minimal backoff value that can be set by the thermal throttling mechanism.
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Some platforms may have power limitations on PCIe cards connected to
specific root ports.
This information is encoded as part of the ACPI tables, for instance:
<snip>
Name (SPLX, Package (0x02)
{
Zero,
Package (0x03)
{
0x07,
0x00000500,
0x80000000
}
})
Method (SPLC, 0, Serialized)
{
Return (SPLX)
}
</snip>
The structure returned contains the domain type, the default power
limitation and the default time window (reserved for future use).
Upon PCI probing, call the relevant ACPI method, parse the returned
structure, and save the power limitation.
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Divide the maximal quota between all the data interfaces even in the
case of a single low latency binding without any other non low latency
interfaces, so that afterwards the quota allocation (which considers
the number of data interfaces) will be correct.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently the quota remainder was added to the first binding, although
it is possible that this was not a data binding (only the P2P_DEVICE
interface is part of the binding).
Fix this by adding the remainder to the first binding that was actually
allocated quota.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This makes the code a little bit longer as zero-extension
has to be done (mov vs. movzwl), but that's miniscule and
the space saving is significant, about 600 bytes in DVM
and 700 bytes in MVM, so the cache effect should be worth
the few bytes more code.
While at it, remove two spurious blank lines in variable
declaration blocks.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This will be useful during tests done on the physical layer.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Allow reading and setting bcast filtering configuration
through debugfs.
By default, mvm->bcast_filters is used for setting
the bcast filtering configuration (these filters
will be configured for each associated station).
For testing purposes, allow overriding this configuration,
and setting the bcast filtering configuration manually.
The following debugfs keys can be used:
* bcast_filtering/override - use debugfs values instead
of default configuration
* bcast_filtering/filters - set filters (+ attributes)
* bcast_filtering/macs - per-mac bcast filtering
configuration (policy + attached filters)
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add our ip as a new attribute to the bcast filtering
configuration (i.e. check the dest ip field of the
arp request).
Add bcast filter to pass incoming dhcp offer
broadcast frames as well (for sta vifs).
In order to support such dynamic configuration,
use the reserved1 field as a bitmap for driver internal
flags (which will indicate we want to configure the ip
in this attribute), and reconfigure the bcast
filtering on BSS_CHANGED_ARP_FILTER indication.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Configure arp request broadcast filter if this
option is enabled, in order to allow only arp
request broadcasts to pass-in.
(A following patch will make this filter even narrower
by limiting the arp request to our own ip)
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Broadcast filtering allows dropping broadcast
frames that don't match the configured patterns.
Use predefined filters, and configure them for
each associated station vif.
There is no need to optimize and attach the same
filter to multiple vifs, as a following patch
will configure each filter to have per-vif unique
values.
Configure the bcast filtering on assoc changes.
Add a new IWLWIFI_BCAST_FILTERING Kconfig option
in order to enable broadcast filtering.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Pontus Fuchs