Based on Arnds review comments here https://lkml.org/lkml/2014/11/13/161,
update the miphy28lp phy driver to access sysconfig register offsets via
syscfg dt property.
This is because the reg property should not be mixing address spaces like
it does currently for miphy28lp. This change then also aligns us to how other
platforms such as keystone and bcm7445 pass there syscon offsets via DT.
I have updated the miphy28lp phy driver same way as Peter's implementation.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
In case of error, the function devm_ioremap_resource() returns
ERR_PTR() and never returns NULL. The NULL test in the return
value check should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Failed test case: Boot without SATA drive connected. Suspend/resume
the board and then connect SATA drive. It fails to enumerate.
Due to Errata i783 "SATA Lockup After SATA DPLL Unlock/Relock"
we can't allow SATA DPLL to be in the unlocked state.
The SATA refclk (sata_ref_clk) is the source of the SATA_DPLL.
This clock is being controlled only by the AHCI SATA driver and is
shut off during system suspend (if the SATA drive was not already attached)
causing the SATA DPLL to be unlocked and so causing errata i783.
To prevent sata_ref_clk from being disabled, we add the control of
this clock to the SATA PHY driver and prevent it from being disabled.
This also fixes the issue of SATA not working on OMAP5/DRA7 when
AHCI platform driver is built as a module.
NOTE: Device tree changes also required for OMAP5 & DRA7.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
On system suspend, the runtime_suspend() driver hook doesn't get
called for USB phy and so the clocks are not disabled in the driver.
This causes the L3INIT_960M_GFCLK and L3INIT_480M_GFCLK to remain
active on the DRA7 platform while in system suspend.
In case of pcie-phy, the runtime_suspend hook gets called after
the suspend hook so we introduce a flag phy->enabled to keep
track if our clocks are enabled or not to prevent multiple
enable/disables.
Add suspend/resume hooks to the driver.
Move enabling/disabling clock code into helper functions.
Reported-by: Nishant Menon <nm@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This change adds a support for a 14nm qcom-ufs phy that is
required in platforms that use ufs-qcom controller.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Dov Levenglick <dovl@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This change adds a support for a 20nm qcom-ufs phy that is required in
platforms that use ufs-qcom controller.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Dov Levenglick <dovl@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This change adds a generic and common API support for ufs phy QUALCOMM
Technologies. This support provides common code and also points
to specific phy callbacks to differentiate between different behaviors
of frequent use-cases (like power on, power off, phy calibration etc).
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Dov Levenglick <dovl@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Based on Arnds review comments here https://lkml.org/lkml/2014/11/13/161,
update the miphy365 phy driver to access sysconfig register offsets via
syscfg dt property.
This is because the reg property should not be mixing address spaces
like it does currently for miphy365. This change then also aligns us
to how other platforms such as keystone and bcm7445 pass there syscon
offsets via DT.
This patch breaks DT compatibility, but this platform is considered WIP,
and is only used by a few developers who are upstreaming support for it.
This change has been done as a single atomic commit to ensure it is
bisectable.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on Arnds review comments here https://lkml.org/lkml/2014/11/13/161,
update the phy driver to not use the reg property to access the sysconfig
register offsets.
This is because other phy's (miphy28, miphy365) have a combination of
memory mapped registers and sysconfig control regs, and we shouldn't
be mixing address spaces in the reg property. In addition we would
ideally like the sysconfig offsets to be passed via DT in a uniform way.
This new method will also allow us to support devices which have sysconfig
registers in different banks more easily and it is also analagous to how
keystone and bcm7745 platforms pass there syscon offsets in DT.
This breaks DT compatibility, but this platform is considered WIP, and
is only used by a few developers who are upstreaming support for it.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to DRA74x silicon rev 1.1, pcie_pcs register bits 8-15 and bits 16-23
were used to configure RC delay count for phy1 and phy2 respectively.
phyid was used as index to distinguish the phys and to configure the delay
values appropriately.
As of DRA74x silicon rev 1.1, pcie_pcs register definition has changed.
Bits 16-23 are used to configure delay values for *both* phy1 and phy2.
Hence phyid is no longer required.
So, drop id field from ti_pipe3 structure and its subsequent references
for configuring pcie_pcs register.
Also, pcie_pcs register now needs to be configured with delay value of 0x96
at bit positions 16-23. See register description of CTRL_CORE_PCIE_PCS in
ARM572x TRM, SPRUHZ6, October 2014, section 18.5.2.2, table 18-1804.
This is needed to ensure Gen2 cards are enumerated consistently.
DRA72x silicon behaves same way as DRA74x rev 1.1 as far as this functionality
is considered.
Test results on DRA74x and DRA72x EVMs:
Before patch
------------
DRA74x ES 1.0: Gen1 cards work, Gen2 cards do not work (expected result due to
silicon errata)
DRA74x ES 1.1: Gen1 cards work, Gen2 cards do not work sometimes due to incorrect
programming of register
DRA72x: Gen1 cards work, Gen2 cards do not work sometimes due to incorrect
programming of register
After patch
-----------
DRA74x ES 1.0: Gen1 cards work, Gen2 cards do not work (expected result due to
silicon errata)
DRA74x ES 1.1: Gen1 cards work, Gen2 cards work consistently.
DRA72x: Gen1 and Gen2 cards enumerate consistently.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The allwinner SDK uses a value of 3 for the disconnect threshold setting on
sun6i, do the same in the kernel.
In my previous experience with sun5i problems getting the threshold right
is important to avoid usb2 devices being unplugged sometimes going unnoticed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
We need to unlock before returning the -EINVAL here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by
the driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken
into account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should
have used from the start and drop some other unuseful KERN_ERR
messages printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool
(Prarit Bhargava).
- Fix two regressions introduced by recent commits in the OPP
library and clean up some existing minor issues in that code
(Viresh Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout
the tree (or drop it where that can be done) in order to make
it possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki,
Ulf Hansson, Ludovic Desroches). There will be one more
"CONFIG_PM_RUNTIME removal" batch after this one, because some
new uses of it have been introduced during the current merge
window, but that should be sufficient to finally get rid of it.
- Make the ACPI EC driver more robust against race conditions
related to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to
disable GPEs that it has not enabled which confuses ACPICA
and makes it report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver
to make it possible to override the blacklisting of some
systems in that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS
entry for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces
witn names that reflect the IDs of the ACPI device objects
they are associated with, except for "generic" ACPI fans
(PNP ID "PNP0C0B"). That's necessary for user space thermal
management tools to be able to connect the fans with the
parts of the system they are supposed to be cooling properly.
From Srinivas Pandruvada.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5fo2
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are regression fixes (leds-gpio, ACPI backlight driver,
operating performance points library, ACPI device enumeration
messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device
PM), some cleanups in the operating performance points (OPP)
framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of
minor intel_pstate driver changes, a new MAINTAINERS entry for it and
an ACPI fan driver change needed for better support of thermal
management in user space.
Specifics:
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by the
driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken into
account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should have
used from the start and drop some other unuseful KERN_ERR messages
printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool (Prarit
Bhargava).
- Fix two regressions introduced by recent commits in the OPP library
and clean up some existing minor issues in that code (Viresh
Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the
tree (or drop it where that can be done) in order to make it
possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf
Hansson, Ludovic Desroches).
There will be one more "CONFIG_PM_RUNTIME removal" batch after this
one, because some new uses of it have been introduced during the
current merge window, but that should be sufficient to finally get
rid of it.
- Make the ACPI EC driver more robust against race conditions related
to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to disable
GPEs that it has not enabled which confuses ACPICA and makes it
report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver to
make it possible to override the blacklisting of some systems in
that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS entry
for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces witn
names that reflect the IDs of the ACPI device objects they are
associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B").
That's necessary for user space thermal management tools to be able
to connect the fans with the parts of the system they are supposed
to be cooling properly. From Srinivas Pandruvada"
* tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
MAINTAINERS: add entry for intel_pstate
ACPI / video: update the skip case for acpi_video_device_in_dod()
power / PM: Eliminate CONFIG_PM_RUNTIME
NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / EC: Fix unexpected ec_remove_handlers() invocations
Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()"
tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c
PM: Remove the SET_PM_RUNTIME_PM_OPS() macro
mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro
PM / Kconfig: Replace PM_RUNTIME with PM in dependencies
ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / PM: Do not disable wakeup GPEs that have not been enabled
ACPI / utils: Drop error messages from acpi_evaluate_reference()
...
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under
drivers/phy/.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
of non-dt boot. Adds three new PHY drivers using the PHY framework and some
miscellaneous fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=oo3u
-----END PGP SIGNATURE-----
Merge tag 'for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-testing
Kishon writes:
Improvements in phy-core specifically on PHY core finds the PHY in the case
of non-dt boot. Adds three new PHY drivers using the PHY framework and some
miscellaneous fixes and cleanups.
The Armada 375 SoC comes with an USB2 host and device controller and
an USB3 controller. The USB cluster control register allows to manage
common features of both USB controllers.
This commit adds a driver integrated in the generic PHY framework to
control this USB cluster feature.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
[ kishon@ti.com : Made it to use the updated devm_phy_create API and
soem cosmentic changes in Kconfig file.]
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: coccinelle/api/ptr_ret.cocci
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This time, a very pull request with 216 non-merge
commits. Most of the commits contained here are
sparse or coccinelle fixes ranging from missing
'static' to returning 0 in case of errors.
More importantly, we have the removal the now
unnecessary 'driver' argument to ->udc_stop().
DWC2 learned about Dual-Role builds. Users of
this IP can now have a single driver built for
host and device roles.
DWC3 got support for two new HW platforms: Exynos7
and AMD.
The Broadcom USB 3.0 Device Controller IP is now
supported and so is PLX USB338x, which means DWC3
has lost is badge as the only USB 3.0 peripheral
IP supported on Linux.
Thanks for Tony Lindgren's work, we can now have
a distro-like kernel where all MUSB glue layers
can be built into the same kernel (statically
or dynamically linked) and it'll work in PIO (DMA
will come probably on v3.20).
Other than these, the usual set of cleanups and
non-critical fixes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WYyZ
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.19 merge window
This time, a very pull request with 216 non-merge
commits. Most of the commits contained here are
sparse or coccinelle fixes ranging from missing
'static' to returning 0 in case of errors.
More importantly, we have the removal the now
unnecessary 'driver' argument to ->udc_stop().
DWC2 learned about Dual-Role builds. Users of
this IP can now have a single driver built for
host and device roles.
DWC3 got support for two new HW platforms: Exynos7
and AMD.
The Broadcom USB 3.0 Device Controller IP is now
supported and so is PLX USB338x, which means DWC3
has lost is badge as the only USB 3.0 peripheral
IP supported on Linux.
Thanks for Tony Lindgren's work, we can now have
a distro-like kernel where all MUSB glue layers
can be built into the same kernel (statically
or dynamically linked) and it'll work in PIO (DMA
will come probably on v3.20).
Other than these, the usual set of cleanups and
non-critical fixes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This PHY controller is also present on Exynos7 platform
in arch-exynos family.
So PHY_EXYNOS5_USBDRD should now depend on ARCH_EXYNOS.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Some Exynos boards have a separate regulator controlling a
Boost 5V supply which goes as input for VBUS regulator.
So adding a control for the same in driver, to enable
vbus supply on the port.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Exynos7 SoC has now separate gate control for 125MHz pipe3 phy
clock, as well as 60MHz utmi phy clock.
Additionally, separate gate control is available for the clock
used for ITP (Isochronous Transfer Packet) generation.
So get the same and control in the phy-exynos5-usbdrd driver.
Suggested-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The users of the old method are now converted to the new one.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
[ kishon@ti.com : made phy-berlin-usb.c and phy-miphy28lp.c to use the updated
devm_phy_create API.]
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Creates the lookup separately. Hard coding the consumer as
it can't be anything else except musb.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Separates registration of the phy and the lookup. The method
is copied from clkdev.c,
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add the driver driving the Marvell Berlin USB PHY. This allows to
initialize the PHY and to use it from the USB driver later.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Berlin BG2 also has a SATA PHY compatible with the current driver
except different PHY_BASE. Add a new compatible to the driver
reflecting the different PHY_BASE.
Acked-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Currently, Berlin SATA PHY driver assumes PHY_BASE address being
constant. While this PHY_BASE is correct for BG2Q, older BG2 PHY_BASE
is different. Prepare the driver for BG2 support by moving the phy_base
into private driver data.
Acked-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The driver for sun4i USB phys currently supports
only phy1 and phy2 which are used for USB host
controllers. This patch adds support for USB phy0,
which is used by the musb hdrc USB controller.
Signed-off-by: Roman Byshko <rbyshko@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Instead of using the node pointer of the PHY provider and then scanning its
child nodes to get a reference to the PHY, directly use the node pointer
present in of_phandle_args to get a reference to the PHY.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch to compensate tx impedance (Sata, PCIe)
depending on Soc cuts the kernel is built for.
Signed-off-by: Giuseppe Condorelli <giuseppe.condorelli@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
SSC is the technique of modulating the operating frequency of a signal
slightly to spread its radiated emissions over a range of frequencies.
This reduction in the maximum emission for a given frequency helps meet
radiated emission requirements.
These settings are applicable for PCIE with Internal clock.
Signed-off-by: Harsh Gupta <harsh.gupta@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch to tune on/off the ssc on miphy sata setup.
User can now enable ssc via dt blob, it is useful to reduce
effects of EMI.
Signed-off-by: Giuseppe Condorelli <giuseppe.condorelli@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The MiPHY28lp is a Generic PHY which can serve various SATA or PCIe
or USB3 devices.
Signed-off-by: alexandre torgue <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
commit e47d925 (usb: move the OTG state
from the USB PHY to the OTG structure) moved
the OTG state field from struct usb_phy to
struct usb_otg but, even though I fixed many
other build breakages, I still missed one
on phy-twl4030-usb.c.
Fix the build breakage now.
While at that, also a build warning introduced
by the same commit.
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The USB OTG port does not work since v3.16 on omap platform.
This is a regression introduced by the commit
eb82a3d846 (phy: omap-usb2: Balance pm_runtime_enable() on probe failure
and remove).
This because the call to pm_runtime_enable() function is moved after the
call to devm_phy_create() function, which has side effect since later in
the subsequent calls of devm_phy_create() there is a check with
pm_runtime_enabled() to configure few things.
Fixes: eb82a3d846
Signed-off-by: Oussama Ghorbel <ghorbel@pivasoftware.com>
Tested-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch prepares the introduction of the generic PHY support in the
USB OTG common functions. The USB PHY member of the OTG structure is
renamed to 'usb_phy' and modifications are done in all drivers accessing
it. Renaming this pointer will allow to keep the compatibility for USB
PHY drivers.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Before using the PHY framework instead of the USB PHY one, we need to
move the OTG state into another place, since it won't be available when
USB PHY isn't used. This patch moves the OTG state into the OTG
structure, and makes all the needed modifications in the drivers
using the OTG state.
[ balbi@ti.com : fix build regressions with phy-tahvo.c, musb_dsps.c,
phy-isp1301-omap, and chipidea's debug.c ]
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch removes the superflous .owner field for drivers which
use the module_platform_driver or platform_driver_register api,
as this is overriden in __platform_driver_register.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Currently the DP_PHY_ENABLE register is mapped in the driver,
and accessed to control power to the PHY.
With mfd-syscon and regmap interface available at our disposal,
it's wise to use that instead of using a 'reg' property for the
controller and allocating a memory resource for that.
To facilitate this, we have added another compatible string
for Exynso5420 SoC to acquire driver data which contains
different DP-PHY-CONTROL register offset.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This driver adds support for USB (1.1 and 2.0) phy for STiH415 and
STiH416 System-On-Chips from STMicroelectronics.
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This is the generic phy driver for the picoPHY ports used by the
USB2 and USB3 Host controllers when controlling usb2/1.1 devices. It
is found on STiH407 SoC family from STMicroelectronics.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
We're using threaded irq on a I2C bus and we're sleeping in
twl4030_usb_irq() as it calls twl4030_usb_linkstat() which
calls the i2c functions. If we ever need to lock for longer
I2C transaction sequences a mutex will allow us to do that
easily.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
There's no longer need for tracking the phy state in the driver
with asleep, we can now rely on runtime PM.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
We don't need twl4030_phy_power() any longer now that we have
the runtime PM calls. Let's get rid of it as it's confusing.
No functional changes, just move the code and use res instead
of ret as we are not returning that value.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
We can now let the interrupt and delayed work do all that's
needed with runtime PM.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Using the module_platform_driver macro to register the driver as this gets
rid of a lot of the boilerplate code.
Also remove .owner field as this gets overridden in __platform_driver_register.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Use the module_platform_driver macro to register the driver as this gets
rid of a lot of the boilerplate code.
Also remove .owner field as this gets overridden in __platform_driver_register.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The site specific OOM messages are unncessary, because they duplicate
messages from the memory subsystem which include dump_stack().
Removing these superflous messages makes the kernel smaller. A discussion
here http://patchwork.ozlabs.org/patch/324158/ found that all error paths
from kzalloc will print a error message, and that any error path which maybe
found which doesn't would be considered a bug in kzalloc.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The site specific OOM messages are unncessary, because they duplicate
messages from the memory subsystem which include dump_stack().
Removing these superflous messages makes the kernel smaller. A discussion
here http://patchwork.ozlabs.org/patch/324158/ found that all error paths
from kzalloc will print a error message, and that any error path which maybe
found which doesn't would be considered a bug in kzalloc.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The site specific OOM messages are unncessary, because they duplicate
messages from the memory subsystem which include dump_stack().
Removing these superflous messages makes the kernel smaller. A discussion
here http://patchwork.ozlabs.org/patch/324158/ found that all error paths
from kzalloc will print a error message, and that any error path which maybe
found which doesn't would be considered a bug in kzalloc.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The site specific OOM messages are unncessary, because they duplicate
messages from the memory subsystem which include dump_stack().
Removing these superflous messages makes the kernel smaller. A discussion
here http://patchwork.ozlabs.org/patch/324158/ found that all error paths
from kzalloc will print a error message, and that any error path which maybe
found which doesn't would be considered a bug in kzalloc.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Currently this driver is missing a check on the return value of devm_kzalloc,
which would cause a NULL pointer dereference in a OOM situation.
This patch adds the aformentioned missing check.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The site specific OOM messages are unncessary, because they duplicate
messages from the memory subsystem which include dump_stack().
Removing these superflous messages makes the kernel smaller. A discussion
here http://patchwork.ozlabs.org/patch/324158/ found that all error paths
from kzalloc will print a error message, and that any error path which maybe
found which doesn't would be considered a bug in kzalloc.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This PHY, though formally being a part of Renesas USBHS controller, contains the
UGCTRL2 register that controls multiplexing of the USB ports (Renesas calls them
channels) to the different USB controllers: channel 0 can be connected to either
PCI EHCI/OHCI or USBHS controllers, channel 2 can be connected to PCI EHCI/OHCI
or xHCI controllers.
This is a new driver for this USB PHY currently already supported under drivers/
usb/phy/. The reason for writing the new driver was the requirement that the
multiplexing of USB channels to the controller be dynamic, depending on what
USB drivers are loaded, rather than static as provided by the old driver. The
infrastructure provided by drivers/phy/phy-core.c seems to fit that purpose
ideally. The new driver only supports device tree probing for now.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
ST SPEAR1340-MIPHY support should be available only on
ST SPEAr1340 machine.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Pratyush Anand <pratyush.anand@st.com>
Cc: Mohit Kumar <mohit.kumar@st.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
ST SPEAR1310-MIPHY support should be available only on
ST SPEAr1310 machine.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Pratyush Anand <pratyush.anand@st.com>
Cc: Mohit Kumar <mohit.kumar@st.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
We index the RX/TX speed select values in the following way:
rx_tx_spd[miphy_phy->sata_gen];
However rx_tx_spd[] starts at index zero and the SATA_GENx's start
at one. In this patch we pad out the first element in rx_tx_spd[]
in an attempt to realign the values.
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Reported-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Enabling GENERIC_PHY in the shared (by most ARM sub-architectures)
defconfig multi_v7_defconfig is prohibited. Instead, we'll enable
it from the Kconfig whenever PHY_MIPHY365X is enabled.
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a MODULE_DEVICE_TABLE call for OF match tables. This allows the
module to be autoloaded based on devicetree information.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Commit 249751f223 ("usb: phy: twl4030-usb: poll for ID disconnect")
added twl4030_id_workaround_work() to deal with lost interrupts
after ID pin goes down. Looks like commit f1ddc24c9e ("usb: phy:
twl4030-usb: remove *set_suspend* and *phy_init* ops") changed
things around for the generic phy framework, and delayed work no
longer got called except initially during boot.
The PHY connect and disconnect interrupts for twl4030-usb are not
working after disconnecting a USB-A cable from the board, and the
deeper idle states for omap are blocked as the USB controller
stays busy.
The issue can be solved by calling delayed work from twl4030_usb_irq()
when ID pin is down and the PHY is not asleep like we already do
in twl4030_id_workaround_work().
But as both twl4030_usb_irq() and twl4030_id_workaround_work()
already do pretty much the same thing, let's call twl4030_usb_irq()
from twl4030_id_workaround_work() instead of adding some more
duplicate code. We also must call sysfs_notify() only when we have
an interrupt and not from the delayed work as notified by
Grazvydas Ignotas <notasas@gmail.com>.
Fixes: f1ddc24c9e ("usb: phy: twl4030-usb: remove *set_suspend* and *phy_init* ops")
Cc: stable@vger.kernel.org # v3.13+
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Commit 30a70b026b ("usb: musb: fix obex in g_nokia.ko causing kernel
panic") attempted to fix runtime PM handling for PHYs that are on the
I2C bus. Commit 3063a12be2 ("usb: musb: fix PHY power on/off") then
changed things around to enable of PHYs that rely on runtime PM.
These changes however broke idling of the PHY and causes at least
100 mW extra power consumption on omaps, which is a lot with
the idle power consumption being below 10 mW range on many devices.
As calling phy_power_on/off from runtime PM calls in the USB
causes complicated issues with I2C connected PHYs, let's just let
the PHY do it's own runtime PM as needed. This leaves out the
dependency between PHYs and USB controller drivers for runtime
PM.
Let's fix the regression for twl4030-usb by adding minimal runtime
PM support. This allows idling the PHY on disconnect.
Note that we are changing to use standard runtime PM handling
for twl4030_phy_init() as that function just checks the state
and does not initialize the PHY. The PHY won't get initialized
until in twl4030_phy_power_on().
Fixes: 30a70b026b ("usb: musb: fix obex in g_nokia.ko causing kernel panic")
Fixes: 3063a12be2 ("usb: musb: fix PHY power on/off")
Cc: stable@vger.kernel.org # v3.15+
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
A handful of driver-related changes. We've had a bunch of them going in through
other branches as well, so it's only a part of what we really have this release.
Larger pieces are:
* Removal of a now unused PWM driver for atmel
- This includes AVR32 changes that have been appropriately acked.
* Performance counter support for the arm CCN interconnect
* OMAP mailbox driver cleanups and consolidation
* PCI and SATA PHY drivers for SPEAr 13xx platforms
* Redefinition (with backwards compatibility!) of PCI DT bindings for Tegra to
better model regulators/power.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=fsP6
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Olof Johansson:
"A handful of driver-related changes. We've had a bunch of them going
in through other branches as well, so it's only a part of what we
really have this release.
Larger pieces are:
- Removal of a now unused PWM driver for atmel
[ This includes AVR32 changes that have been appropriately acked ]
- Performance counter support for the arm CCN interconnect
- OMAP mailbox driver cleanups and consolidation
- PCI and SATA PHY drivers for SPEAr 13xx platforms
- Redefinition (with backwards compatibility!) of PCI DT bindings for
Tegra to better model regulators/power"
Note: this merge also fixes up the semantic conflict with the new
calling convention for devm_phy_create(), see commit f0ed817638 ("phy:
core: Let node ptr of PHY point to PHY and not of PHY provider") that
came in through Greg's USB tree.
Semantic merge patch by Stephen Rothwell <sfr@canb.auug.org.au> through
the next tree.
* tag 'drivers-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
bus: arm-ccn: Fix error handling at event allocation
mailbox/omap: add a parent structure for every IP instance
mailbox/omap: remove the private mailbox structure
mailbox/omap: consolidate OMAP mailbox driver
mailbox/omap: simplify the fifo assignment by using macros
mailbox/omap: remove omap_mbox_type_t from mailbox ops
mailbox/omap: remove OMAP1 mailbox driver
mailbox/omap: use devm_* interfaces
bus: ARM CCN: add PERF_EVENTS dependency
bus: ARM CCN PMU driver
PCI: spear: Remove spear13xx_pcie_remove()
PCI: spear: Fix Section mismatch compilation warning for probe()
ARM: tegra: Remove legacy PCIe power supply properties
PCI: tegra: Remove deprecated power supply properties
PCI: tegra: Implement accurate power supply scheme
ARM: SPEAr13xx: Update defconfigs
ARM: SPEAr13xx: Add pcie and miphy DT nodes
ARM: SPEAr13xx: Add bindings and dt node for misc block
ARM: SPEAr13xx: Fix static mapping table
phy: Add drivers for PCIe and SATA phy on SPEAr13xx
...
This is the bulk of new SoC enablement and other platform changes for 3.17:
* Samsung S5PV210 has been converted to DT and multiplatform
* Clock drivers and bindings for some of the lower-end i.MX 1/2 platforms
* Kirkwood, one of the popular Marvell platforms, is folded into the
mvebu platform code, removing mach-kirkwood.
* Hwmod data for TI AM43xx and DRA7 platforms.
* More additions of Renesas shmobile platform support
* Removal of plat-samsung contents that can be removed with S5PV210 being
multiplatform/DT-enabled and the other two old platforms being removed.
New platforms (most with only basic support right now):
* Hisilicon X5HD2 settop box chipset is introduced
* Mediatek MT6589 (mobile chipset) is introduced
* Broadcom BCM7xxx settop box chipset is introduced
+ as usual a lot other pieces all over the platform code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=5TJ6
-----END PGP SIGNATURE-----
Merge tag 'soc-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"This is the bulk of new SoC enablement and other platform changes for
3.17:
- Samsung S5PV210 has been converted to DT and multiplatform
- Clock drivers and bindings for some of the lower-end i.MX 1/2
platforms
- Kirkwood, one of the popular Marvell platforms, is folded into the
mvebu platform code, removing mach-kirkwood
- Hwmod data for TI AM43xx and DRA7 platforms
- More additions of Renesas shmobile platform support
- Removal of plat-samsung contents that can be removed with S5PV210
being multiplatform/DT-enabled and the other two old platforms
being removed
New platforms (most with only basic support right now):
- Hisilicon X5HD2 settop box chipset is introduced
- Mediatek MT6589 (mobile chipset) is introduced
- Broadcom BCM7xxx settop box chipset is introduced
+ as usual a lot other pieces all over the platform code"
* tag 'soc-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (240 commits)
ARM: hisi: remove smp from machine descriptor
power: reset: move hisilicon reboot code
ARM: dts: Add hix5hd2-dkb dts file.
ARM: debug: Rename Hi3716 to HIX5HD2
ARM: hisi: enable hix5hd2 SoC
ARM: hisi: add ARCH_HISI
MAINTAINERS: add entry for Broadcom ARM STB architecture
ARM: brcmstb: select GISB arbiter and interrupt drivers
ARM: brcmstb: add infrastructure for ARM-based Broadcom STB SoCs
ARM: configs: enable SMP in bcm_defconfig
ARM: add SMP support for Broadcom mobile SoCs
Documentation: arm: misc updates to Marvell EBU SoC status
Documentation: arm: add URLs to public datasheets for the Marvell Armada XP SoC
ARM: mvebu: fix build without platforms selected
ARM: mvebu: add cpuidle support for Armada 38x
ARM: mvebu: add cpuidle support for Armada 370
cpuidle: mvebu: add Armada 38x support
cpuidle: mvebu: add Armada 370 support
cpuidle: mvebu: rename the driver from armada-370-xp to mvebu-v7
ARM: mvebu: export the SCU address
...
This has the added advantages of being able to enable/disable each
of the channels as simply as enabling/disabling the DT node.
Suggested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The MiPHY365x is a Generic PHY which can serve various SATA or PCIe
devices. It has 2 ports which it can use for either; both SATA, both
PCIe or one of each in any configuration.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a PHY driver for uses with AHCI based SATA controller driver on the
IPQ806x family of SoCs.
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch fixes a possible timeout in poll loop without actually
checking the register before return. In theory the there is a possibility
of loop being scheduled after a long lock/delay, which would then force
the loop to exit without actually checking the register.
Reported-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
In case of multi-phy PHY providers, each PHY should be modeled as a sub
node of the PHY provider. Then each PHY will have a different node pointer
(node pointer of sub node) than that of PHY provider. Added this provision
in the PHY core.
Also fixed all drivers to use the updated API.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Fixed of_phy_provider_lookup to return 'phy_provider' if _of_phy_get
passes the node pointer of the sub-node of phy provider node. This is
needed when phy provider implements multiple PHYs and each PHY is
modelled as the sub-node of PHY provider device node.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
The Berlin SoC has a two SATA ports. Add a PHY driver to handle them.
The mode selection can let us think this PHY can be configured to fit
other purposes. But there are reasons to think the SATA mode will be
the only one usable: the PHY registers are only accessible indirectly
through two registers in the SATA range, the PHY seems to be integrated
and no information tells us the contrary. For these reasons, make the
driver a SATA PHY driver.
Signed-off-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
mach-kirkwood has been removed, now that kirkwood lives in mach-mvebu.
Depend on MACH_KIRKWOOD, which will be set when these SoCs are built
as part of mach-mvebv.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a PHY driver for uses with AHCI based SATA controller driver on the
APQ8064 family of SoCs.
This patch is a forward port from Qualcomm's v3.4 andriod kernel.
Tested on IFC6410 board.
CC: Sujit Reddy Thumma <sthumma@codeaurora.org>
Tested-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
USB DWC3 driver on Exynos platform does not work without its
corresponding phy driver. Hence make the PHY driver depend on
Exynos DWC3 driver and default it to yes to make things easier
for the end user.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Tested-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Since the USB 2.0 PHYs are required with EHCI/OHCI USB drivers and
USB gadget controller supported by the DWC2 gadget driver, make it
depend on them and default to ARCH_EXYNOS as they are meant for
Exynos platforms. Also, make the sub-drivers silent options enabling
them based on the SoC platforms that they are meant to work with. This
will make life easier for end users who do not have any way knowing the
dependencies.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Tested-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Some PHYs can be powered by an external power regulator.
e.g. USB_HS PHY on DRA7 SoC. Make the PHY core support a
power regulator.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds support for Exynos3250 SoC to Exynos2USB PHY driver.
Although Exynos3250 has only one device phy interface, the register
layout and all operations that are required to get it enabled are almost
same as on Exynos4x12. The only different is one more register
(REFCLKSEL) which need to be set and lack of MODE SWITCH register.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
8-bit delay value (0xF1) is required for GEN2 devices to be enumerated
consistently. Added an API to be called from PHY drivers to set this delay
value and called it from PIPE3 driver to set the delay value.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
PCIe PHY uses an external pll instead of the internal pll used by SATA
and USB3. So added support in pipe3 PHY to use external pll.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
The Exynos4412 USB 2.0 PHY hardware differs from the description provided
in the documentation. Some register bits have different function. This
patch fixes the defines of register bits and changes the way how phys are
powered on and off.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Tested-by: Daniel Drake <drake@endlessm.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Make local functions static, because these are used only in this
file.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
PTR_ERR_OR_ZERO simplifies the code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
PTR_ERR_OR_ZERO simplifies the code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
PTR_ERR_OR_ZERO simplifies the code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Jingoo Han <jg1.han@samsung.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add support for the Samsung's S5PV210 SoC to the Exynos USB 2.0 PHY driver.
Signed-off-by: Mateusz Krawczuk <m.krawczuk@partner.samsung.com>
[k.debski@samsung.com: cleanup and commit description]
[k.debski@samsung.com: make changes accordingly to the mailing list
comments]
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
ARM based ST Microelectronics's SPEAr1310/40 platforms uses ST's phy (known as
'miphy') for PCIe and SATA. This patch adds drivers for these miphys.
This also adds proper bindings for miphys.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Tested-by: Mohit Kumar <mohit.kumar@st.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
[viresh: fixed logs/cclist/checkpatch warnings, broken into smaller patches]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Here are some small USB fixes, PHY driver fixes (they ended up in this
tree for lack of somewhere else to put them), and some new USB device
ids.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlPBnZAACgkQMUfUDdst+ynTkACgwma2Ccj7DJl3g1zFEtM0h8ki
8RYAnirwiO0p1B7gIKlDIgGs25JIwN61
=tNZ2
-----END PGP SIGNATURE-----
Merge tag 'usb-3.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes, PHY driver fixes (they ended up in this
tree for lack of somewhere else to put them), and some new USB device
ids"
* tag 'usb-3.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
phy: omap-usb2: Balance pm_runtime_enable() on probe failure and remove
phy: core: Fix error path in phy_create()
drivers: phy: phy-samsung-usb2.c: Add missing MODULE_DEVICE_TABLE
phy: omap-usb2: fix devm_ioremap_resource error detection code
phy: sun4i: depend on RESET_CONTROLLER
USB: serial: ftdi_sio: Add Infineon Triboard
USB: ftdi_sio: Add extra PID.
usb: option: Add ID for Telewell TW-LTE 4G v2
USB: cp210x: add support for Corsair usb dongle
If probe fails then we need to call pm_runtime_disable() to balance
out the previous pm_runtime_enable() call. Else it will cause
unbalanced pm_runtime_enable() call in the succeding probe call.
This anomaly was observed when the call to devm_phy_create() failed
with -EPROBE_DEFER.
Balance out the pm_runtime_enable() call in .remove() as well.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prevent resources from being freed twice in case device_add() call
fails within phy_create(). Also use ida_simple_remove() instead of
ida_remove() as we had used ida_simple_get() to allocate the ida.
Cc: 3.13+ <stable@vger.kernel.org> # 3.13+
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allow phy-exynos-usb2 to be autoloaded based on devicetree information.
Tested on Odroid X2 with its USB subsystem build as modules.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devm_ioremap_resource returns an ERR_PTR value, not NULL, on failure.
A simplified version of the semantic match that finds this problem is as
follows:
// <smpl>
@@
expression e,e1;
statement S;
@@
*e = devm_ioremap_resource(...);
if (!e1) S
// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver depend on the reset framework in a mandatory way. Make sure
reset_control_get is defined by adding this dependency in Kconfig
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When NO_IOMEM is enabled (e.g. score architecture), some drivers which
need HAS_IOMEM need notice about it, or it will report related warning:
warning: (GPIO_SCH && GPIO_ICH && GPIO_VX855 && GPIO_RDC321X && IE6XX_WDT && RADIO_WL1273 && HID_SENSOR_HUB && MFD_NVEC) selects MFD_CORE which has unmet direct dependencies (HAS_IOMEM)
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The USB phy controller in the A31 differs mostly from the older controllers
because it has a clock dedicated for each phy, while the older ones were having
a single clock for all the phys.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Move the phy initialization and variables declaration to the loop itself, since
it is where it really belongs. Also remove all the temporary variables, we can
use the structure members directly.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Adding support to enable/disable VBUS controlled by a
regulator, to enable vbus supply on the port.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a new driver for the USB 3.0 PHY on Exynos5 series of SoCs.
The new driver uses the generic PHY framework and will interact
with DWC3 controller present on Exynos5 series of SoCs.
Also, created a new header file in linux/mfd/syscon/ for
Exynos5 SoCs and put the required PMU offset definitions
for the basic available PHYs.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
All other phy drivers use 'select', while this one is
the only one to use 'depends on'. This is not a bug, just
slightly inconsistent, so let's change it to do things the
same way as everyone else.
We may also want to turn GENERIC_PHY into a silent option
that only ever gets turned on if another driver needs it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Matt Porter <mporter@linaro.org>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The phys array is of size EXYNOS_MIPI_PHYS_NUM. Trying to access the
index EXYNOS_MIPI_PHYS_NUM should return an error.
Fixes: 069d2e26e9 "phy: Add driver for Exynos MIPI CSIS/DSIM DPHYs"
Signed-off-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Gabriel FERNANDEZ