gcc 4.4 warns about:
drivers/parisc/lba_pci.c: In function 'lba_pat_resources':
drivers/parisc/lba_pci.c:1099: warning: the frame size of 8280 bytes is larger than 4096 bytes
The problem is we declare two large structures on the stack. They don't need
to be on the stack since they are only used during LBA initialization (which
is serialized). Moving to be "static".
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
The defines and typedefs (hw_interrupt_type, no_irq_type, irq_desc_t) have
been kept around for migration reasons. After more than two years it's
time to remove them finally.
This patch cleans up one of the remaining users. When all such patches
hit mainline we can remove the defines and typedefs finally.
Impact: cleanup
Convert the last remaining users to struct irq_chip and remove the
define.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Alex Chiang asked me why PARISC was calling pci_bus_add_devices()
and pci_bus_assign_resources() in the opposite order from everyone else.
No reason and I couldn't see any data dependency.
Patch below applies cleanly to 2.6.30-rc2.
Later, I suspected the code worked only because no drivers would be
loaded/ready until much later in the system initialization sequence.
Tested "LBA" code on J6000 (32-bit) and A500 (64-bit SMP) with 2.6.30-rc2.
Not tested with any Dino controllers.
Not tested with PCI-PCI Bridge (TBD).
Reported-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Fix this build error when CONFIG_PROC_FS is not set:
drivers/parisc/ccio-dma.c:1574: error: 'ccio_proc_info_fops' undeclared
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Cc: linux-parisc@vger.kernel.org
Cc: Helge Deller <deller@gmx.de>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
according to Ingo, change set_affinity() in irq_chip should return int,
because that way we can handle failure cases in a much cleaner way, in
the genirq layer.
v2: fix two typos
[ Impact: extend API ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: linux-arch@vger.kernel.org
LKML-Reference: <49F654E9.4070809@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
ccio-dma.c:456: warning: overflow in implicit constant conversion
ccio-dma.c:459: warning: overflow in implicit constant conversion
ccio-dma.c:1032: warning: unused variable 'j'
ccio-dma.c:1031: warning: unused variable 'max'
ccio-dma.c:1031: warning: unused variable 'min'
ccio-dma.c:1031: warning: unused variable 'avg'
ccio-dma.c:1403: warning: format '%08lx' expects type 'long unsigned int', but argument 3 has type 'resource_size_t'
ccio-dma.c:1403: warning: format '%08lx' expects type 'long unsigned int', but argument 4 has type 'resource_size_t'
ccio-dma.c:1554: warning: format '%lx' expects type 'long unsigned int', but argument 3 has type 'resource_size_t'
dino.c:822: warning: format '%lx' expects type 'long unsigned int', but argument 4 has type 'resource_size_t'
dino.c:822: warning: format '%lx' expects type 'long unsigned int', but argument 5 has type 'resource_size_t'
dino.c:902: warning: format '%lx' expects type 'long unsigned int', but argument 3 has type 'resource_size_t'
dino.c:902: warning: format '%lx' expects type 'long unsigned int', but argument 4 has type 'resource_size_t'
asp.c:84: warning: format '%lx' expects type 'long unsigned int', but argument 4 has type 'resource_size_t'
eisa.c:317: warning: format '%08lx' expects type 'long unsigned int', but argument 3 has type 'resource_size_t'
eisa_enumerator.c:101: warning: format '%lx' expects type 'long unsigned int', but argument 2 has type 'resource_size_t'
eisa_enumerator.c:101: warning: format '%lx' expects type 'long unsigned int', but argument 3 has type 'resource_size_t'
eisa_enumerator.c:191: warning: format '%lx' expects type 'long unsigned int', but argument 2 has type 'resource_size_t'
eisa_enumerator.c:191: warning: format '%lx' expects type 'long unsigned int', but argument 3 has type 'resource_size_t'
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
drivers/parisc/iosapic.c:717: error: incompatible types in assignment
irq_desc::affinity was changed from cpumask_t to cpumask_var_t in
7f7ace0cda (cpumask: update irq_desc to use cpumask_var_t)
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
- depending on machine type, blink all leds or just the loadavg
leds twice a second on oops.
- cancel_rearming_delayed_workqueue() is obsolete,
use cancel_delayed_work_sync() instead
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
CC drivers/parisc/sba_iommu.o
drivers/parisc/sba_iommu.c:1373: error: expected identifier or '('
before '}' token
make[2]: *** [drivers/parisc/sba_iommu.o] Error 1
make[1]: *** [drivers/parisc] Error 2
make: *** [drivers] Error 2
Don't know how this has gone missed for so long... clearly I need
to do builds on my C8000 more often.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> posted a patch series
to linux-pci to fix a wrong assumption about pci_bus->self==NULL for
all PCI host bus controllers. While PARISC platforms to not behave
this way, I prefer to have the code consistent across architectures.
The following patch replaces pci_bus->self with pci_bus->parent when
used as a test to check for "root bus controller".
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
commit 11c3b5c3e0
Author: Greg Kroah-Hartman <gregkh@suse.de>
Date: Tue Dec 16 12:24:56 2008 -0800
driver core: move klist_children into private structure
Broke our parisc build pretty badly because we touch the klists directly
in three cases (AGP, SBA and GSC). Although GregKH will revert this
patch, there's no reason we should be using the iterators directly, we
can just move to the standard device_for_each_child() API.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Move DMA-mapping.txt to Documentation/PCI/.
DMA-mapping.txt was supposed to be moved from Documentation/ to
Documentation/PCI/. The 00-INDEX files in those two directories
were updated, along with a few other text files, but the file
itself somehow escaped being moved, so move it and update more
text files and source files with its new location.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit b430428a18 ("8250: Don't clobber
spinlocks.") introduced a regression on the parisc architecture, which
broke the handover to the serial port at boottime.
early_serial_setup() was changed to only copy a subset of the uart_port
fields, and sadly the "type" and "line" fields were forgotten and thus
the serial port was not initialized and could not be used for a
handover. This patch fixes this by copying the missing fields.
As this change to early_serial_setup() doesn't need an initialized
spinlock in the uart_port struct any longer, we can drop the spinlock
initialization in the superio driver.
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Cc: linux-parisc@vger.kernel.org
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
parisc: export length of os_hpmc vector
parisc: fix kernel crash (protection id trap) when compiling ruby1.9
parisc: Use DEFINE_SPINLOCK
parisc: add uevent helper for parisc bus
parisc: fix ipv6 checksum
parisc: quiet palo not-found message from "which"
parisc: Replace NR_CPUS in parisc code
parisc: trivial fixes
parisc: fix braino in commit adding __space_to_prot
parisc: factor out sid to protid conversion
parisc: use leX_to_cpu in place of __fswabX
parisc: fix GFP_KERNEL use while atomic in unwinder
parisc: remove dead BIO_VMERGE_BOUNDARY and BIO_VMERGE_MAX_SIZE definitions
parisc: set_time() catch errors
parisc: use the new byteorder headers
parisc: drivers/parisc/: make code static
parisc: lib/: make code static
* 'cpus4096-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (66 commits)
x86: export vector_used_by_percpu_irq
x86: use logical apicid in x2apic_cluster's x2apic_cpu_mask_to_apicid_and()
sched: nominate preferred wakeup cpu, fix
x86: fix lguest used_vectors breakage, -v2
x86: fix warning in arch/x86/kernel/io_apic.c
sched: fix warning in kernel/sched.c
sched: move test_sd_parent() to an SMP section of sched.h
sched: add SD_BALANCE_NEWIDLE at MC and CPU level for sched_mc>0
sched: activate active load balancing in new idle cpus
sched: bias task wakeups to preferred semi-idle packages
sched: nominate preferred wakeup cpu
sched: favour lower logical cpu number for sched_mc balance
sched: framework for sched_mc/smt_power_savings=N
sched: convert BALANCE_FOR_xx_POWER to inline functions
x86: use possible_cpus=NUM to extend the possible cpus allowed
x86: fix cpu_mask_to_apicid_and to include cpu_online_mask
x86: update io_apic.c to the new cpumask code
x86: Introduce topology_core_cpumask()/topology_thread_cpumask()
x86: xen: use smp_call_function_many()
x86: use work_on_cpu in x86/kernel/cpu/mcheck/mce_amd_64.c
...
Fixed up trivial conflict in kernel/time/tick-sched.c manually
Impact: change existing irq_chip API
Not much point with gentle transition here: the struct irq_chip's
setaffinity method signature needs to change.
Fortunately, not widely used code, but hits a few architectures.
Note: In irq_select_affinity() I save a temporary in by mangling
irq_desc[irq].affinity directly. Ingo, does this break anything?
(Folded in fix from KOSAKI Motohiro)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Acked-by: Ingo Molnar <mingo@redhat.com>
Cc: ralf@linux-mips.org
Cc: grundler@parisc-linux.org
Cc: jeremy@xensource.com
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
In order for the network device ops get_stats call to be immutable, the handling
of the default internal network device stats block has to be changed. Add a new
helper function which replaces the old use of internal_get_stats.
Note: change return code to make it clear that the caller should not
go changing the returned statistics.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add CONFIG_HAVE_SPARSE_IRQ to for use condensed array.
Get rid of irq_desc[] array assumptions.
Preallocate 32 irq_desc, and irq_desc() will try to get more.
( No change in functionality is expected anywhere, except the odd build
failure where we missed a code site or where a crossing commit itroduces
new irq_desc[] usage. )
v2: according to Eric, change get_irq_desc() to irq_desc()
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Wilcox <willy@debian.org>
Cc: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Use proc_create() to make sure that ->proc_fops be setup before gluing PDE to
main tree.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Cc: Kyle McMartin <kyle@parisc-linux.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the parisc usage of the global_list, as it's not needed anymore.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On 32bits boxes, boundary_size becomes zero due to a overflow and we
hit BUG_ON in iommu_is_span_boundary.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Kyle McMartin <kyle@parisc-linux.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds struct device argument to sba_alloc_range and ccio_alloc_range, a
preparation for modifications to fix the IOMMU segment boundary problem. This
change enables ccio_alloc_range to access to LLD's segment boundary limits.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Kyle McMartin <kyle@parisc-linux.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is no need for kobject_unregister() anymore, thanks to Kay's
kobject cleanup changes, so replace all instances of it with
kobject_put().
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stop using kobject_register, as this way we can control the sending of
the uevent properly, after everything is properly initialized.
Cc: Kyle McMartin <kyle@parisc-linux.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Using a kset for this simple directory is an overkill.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Thibaut VARENE <varenet@parisc-linux.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Kyle McMartin <kyle@parisc-linux.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is no firmware "subsystem" it's just a directory in /sys that
other portions of the kernel want to hook into. So make it a kobject
not a kset to help alivate anyone who tries to do some odd kset-like
things with this.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Dynamically create the kset instead of declaring it statically.
This makes the kobject attributes now work properly that I broke in the
previous patch.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Thibaut VARENE <varenet@parisc-linux.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Kyle McMartin <kyle@parisc-linux.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This makes the code a bit simpler and and gets us one step closer to
deleting the deprecated subsys_attr code.
NOTE, this needs the next patch in the series in order to work properly.
This will build, but the sysfs files will not properly operate.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Thibaut VARENE <varenet@parisc-linux.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Kyle McMartin <kyle@parisc-linux.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We don't need a "default" ktype for a kset. We should set this
explicitly every time for each kset. This change is needed so that we
can make ksets dynamic, and cleans up one of the odd, undocumented
assumption that the kset/kobject/ktype model has.
This patch is based on a lot of help from Kay Sievers.
Nasty bug in the block code was found by Dave Young
<hidave.darkstar@gmail.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
radeonfb was HPMC-ing my C8000 by trying to map its expansion rom from
IO_VIEW, instead of PA_VIEW. Fix seems to be to ensure that its disabled
ROM is properly inserted into the resource tree.
FIXME: this will result in a whinging printk for cards which share expansion
ROMS, such as a quad tulip. Thankfully, it isn't harmful.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
arch/parisc/kernel/pci-dma.c: In function 'pa11_dma_map_sg':
arch/parisc/kernel/pci-dma.c:487: error: 'struct scatterlist' has no member named 'page'
arch/parisc/kernel/pci-dma.c: In function 'pa11_dma_unmap_sg':
arch/parisc/kernel/pci-dma.c:508: error: 'struct scatterlist' has no member named 'page'
arch/parisc/kernel/pci-dma.c:508: error: 'struct scatterlist' has no member named 'page'
arch/parisc/kernel/pci-dma.c: In function 'pa11_dma_sync_sg_for_cpu':
arch/parisc/kernel/pci-dma.c:535: error: 'struct scatterlist' has no member named 'page'
arch/parisc/kernel/pci-dma.c:535: error: 'struct scatterlist' has no member named 'page'
arch/parisc/kernel/pci-dma.c: In function 'pa11_dma_sync_sg_for_device':
arch/parisc/kernel/pci-dma.c:545: error: 'struct scatterlist' has no member named 'page'
arch/parisc/kernel/pci-dma.c:545: error: 'struct scatterlist' has no member named 'page'
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
pcibios_link_hba_resources() could corrupt the resource tree by inserting
resources in the wrong place. Fix this by calling pci_claim_resource()
for PCI-PCI bridges. Delete pcibios_link_hba_resources as we shouldn't
need it any more. Also get rid of lba_claim_dev_resources() and just
call pci_claim_resource() directly.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Failing to create the links doesn't seem like a fatal error in these
paths. WARN_ON seems better than nothing though.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
If we have a SuckyIO, and pci_enable_device fails, we'll be in a world of
hurt anyways, so we might as well BUG_ON.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
This patch makes most of the generic device layer network
namespace safe. This patch makes dev_base_head a
network namespace variable, and then it picks up
a few associated variables. The functions:
dev_getbyhwaddr
dev_getfirsthwbytype
dev_get_by_flags
dev_get_by_name
__dev_get_by_name
dev_get_by_index
__dev_get_by_index
dev_ioctl
dev_ethtool
dev_load
wireless_process_ioctl
were modified to take a network namespace argument, and
deal with it.
vlan_ioctl_set and brioctl_set were modified so their
hooks will receive a network namespace argument.
So basically anthing in the core of the network stack that was
affected to by the change of dev_base was modified to handle
multiple network namespaces. The rest of the network stack was
simply modified to explicitly use &init_net the initial network
namespace. This can be fixed when those components of the network
stack are modified to handle multiple network namespaces.
For now the ifindex generator is left global.
Fundametally ifindex numbers are per namespace, or else
we will have corner case problems with migration when
we get that far.
At the same time there are assumptions in the network stack
that the ifindex of a network device won't change. Making
the ifindex number global seems a good compromise until
the network stack can cope with ifindex changes when
you change namespaces, and the like.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
early_serial_setup was removed from serial.h, but forgot to put in
serial_8250.h
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes the following build-error:
CC drivers/parisc/hppb.o
drivers/parisc/hppb.c: In function ‘hppb_probe’:
drivers/parisc/hppb.c:73: error: implicit declaration of function ‘ccio_request_resource’
Signed-off-by: Frank Lichtenheld <frank@lichtenheld.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sysfs is now completely out of driver/module lifetime game. After
deletion, a sysfs node doesn't access anything outside sysfs proper,
so there's no reason to hold onto the attribute owners. Note that
often the wrong modules were accounted for as owners leading to
accessing removed modules.
This patch kills now unnecessary attribute->owner. Note that with
this change, userland holding a sysfs node does not prevent the
backing module from being unloaded.
For more info regarding lifetime rule cleanup, please read the
following message.
http://article.gmane.org/gmane.linux.kernel/510293
(tweaked by Greg to not delete the field just yet, to make it easier to
merge things properly.)
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Hi Kyle,
this patch fixes the following section mismatch (EISA cards should be hotplug aware, but the EISA bus itself shouldn't):
WARNING: drivers/built-in.o(.text.eisa_probe+0x220): Section mismatch: reference to .init.text:eisa_root_register (after 'eisa_probe')
Please apply,
Helge
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Clean up ROUNDUP, Use ALIGN where ever appropriate.
Signed-off-by: Milind Arun Choudhary <milindchoudhary@gmail.com>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Remove includes of <linux/smp_lock.h> where it is not used/needed.
Suggested by Al Viro.
Builds cleanly on x86_64, i386, alpha, ia64, powerpc, sparc,
sparc64, and arm (all 59 defconfigs).
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (49 commits)
[SCTP]: Set assoc_id correctly during INIT collision.
[SCTP]: Re-order SCTP initializations to avoid race with sctp_rcv()
[SCTP]: Fix the SO_REUSEADDR handling to be similar to TCP.
[SCTP]: Verify all destination ports in sctp_connectx.
[XFRM] SPD info TLV aggregation
[XFRM] SAD info TLV aggregationx
[AF_RXRPC]: Sort out MTU handling.
[AF_IUCV/IUCV] : Add missing section annotations
[AF_IUCV]: Implementation of a skb backlog queue
[NETLINK]: Remove bogus BUG_ON
[IPV6]: Some cleanups in include/net/ipv6.h
[TCP]: zero out rx_opt in tcp_disconnect()
[BNX2]: Fix TSO problem with small MSS.
[NET]: Rework dev_base via list_head (v3)
[TCP] Highspeed: Limited slow-start is nowadays in tcp_slow_start
[BNX2]: Update version and reldate.
[BNX2]: Print bus information for PCIE devices.
[BNX2]: Add 1-shot MSI handler for 5709.
[BNX2]: Restructure PHY event handling.
[BNX2]: Add indirect spinlock.
...
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6:
remove "struct subsystem" as it is no longer needed
sysfs: printk format warning
DOC: Fix wrong identifier name in Documentation/driver-model/devres.txt
platform: reorder platform_device_del
Driver core: fix show_uevent from taking up way too much stack
Cleanup of dev_base list use, with the aim to simplify making device
list per-namespace. In almost every occasion, use of dev_base variable
and dev->next pointer could be easily replaced by for_each_netdev
loop. A few most complicated places were converted to using
first_netdev()/next_netdev().
Signed-off-by: Pavel Emelianov <xemul@openvz.org>
Acked-by: Kirill Korotaev <dev@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I noticed that many source files include <linux/pci.h> while they do
not appear to need it. Here is an attempt to clean it all up.
In order to find all possibly affected files, I searched for all
files including <linux/pci.h> but without any other occurence of "pci"
or "PCI". I removed the include statement from all of these, then I
compiled an allmodconfig kernel on both i386 and x86_64 and fixed the
false positives manually.
My tests covered 66% of the affected files, so there could be false
positives remaining. Untested files are:
arch/alpha/kernel/err_common.c
arch/alpha/kernel/err_ev6.c
arch/alpha/kernel/err_ev7.c
arch/ia64/sn/kernel/huberror.c
arch/ia64/sn/kernel/xpnet.c
arch/m68knommu/kernel/dma.c
arch/mips/lib/iomap.c
arch/powerpc/platforms/pseries/ras.c
arch/ppc/8260_io/enet.c
arch/ppc/8260_io/fcc_enet.c
arch/ppc/8xx_io/enet.c
arch/ppc/syslib/ppc4xx_sgdma.c
arch/sh64/mach-cayman/iomap.c
arch/xtensa/kernel/xtensa_ksyms.c
arch/xtensa/platform-iss/setup.c
drivers/i2c/busses/i2c-at91.c
drivers/i2c/busses/i2c-mpc.c
drivers/media/video/saa711x.c
drivers/misc/hdpuftrs/hdpu_cpustate.c
drivers/misc/hdpuftrs/hdpu_nexus.c
drivers/net/au1000_eth.c
drivers/net/fec_8xx/fec_main.c
drivers/net/fec_8xx/fec_mii.c
drivers/net/fs_enet/fs_enet-main.c
drivers/net/fs_enet/mac-fcc.c
drivers/net/fs_enet/mac-fec.c
drivers/net/fs_enet/mac-scc.c
drivers/net/fs_enet/mii-bitbang.c
drivers/net/fs_enet/mii-fec.c
drivers/net/ibm_emac/ibm_emac_core.c
drivers/net/lasi_82596.c
drivers/parisc/hppb.c
drivers/sbus/sbus.c
drivers/video/g364fb.c
drivers/video/platinumfb.c
drivers/video/stifb.c
drivers/video/valkyriefb.c
include/asm-arm/arch-ixp4xx/dma.h
sound/oss/au1550_ac97.c
I would welcome test reports for these files. I am fine with removing
the untested files from the patch if the general opinion is that these
changes aren't safe. The tested part would still be nice to have.
Note that this patch depends on another header fixup patch I submitted
to LKML yesterday:
[PATCH] scatterlist.h needs types.h
http://lkml.org/lkml/2007/3/01/141
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We need to work on cleaning up the relationship between kobjects, ksets and
ktypes. The removal of 'struct subsystem' is the first step of this,
especially as it is not really needed at all.
Thanks to Kay for fixing the bugs in this patch.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Herbert Xu conviced me that a new flag was overkill; every driver
currently overrides get_stats, so we might as well make the internal
one the default. If someone did fail to set get_stats, they would now
get all 0 stats instead of "No statistics available".
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Network drivers which keep stats allocate their own stats structure
then write a get_stats() function to return them. It would be nice if
this were done by default.
1) Add a new "stats" field to "struct net_device".
2) Add a new feature field to say "this driver uses the internal one"
3) Have a default "get_stats" which returns NULL if that feature not set.
4) Change callers to check result of get_stats call for NULL, not if
->get_stats is set.
This should not break backwards compatibility with older drivers, yet
allow modern drivers to shed some boilerplate code.
Lightly tested: works for a modified lguest network driver.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/kyle/parisc-2.6: (78 commits)
[PARISC] Use symbolic last syscall in __NR_Linux_syscalls
[PARISC] Add missing statfs64 and fstatfs64 syscalls
Revert "[PARISC] Optimize TLB flush on SMP systems"
[PARISC] Compat signal fixes for 64-bit parisc
[PARISC] Reorder syscalls to match unistd.h
Revert "[PATCH] make kernel/signal.c:kill_proc_info() static"
[PARISC] fix sys_rt_sigqueueinfo
[PARISC] fix section mismatch warnings in harmony sound driver
[PARISC] do not export get_register/set_register
[PARISC] add ENTRY()/ENDPROC() and simplify assembly of HP/UX emulation code
[PARISC] convert to use CONFIG_64BIT instead of __LP64__
[PARISC] use CONFIG_64BIT instead of __LP64__
[PARISC] add ASM_EXCEPTIONTABLE_ENTRY() macro
[PARISC] more ENTRY(), ENDPROC(), END() conversions
[PARISC] fix ENTRY() and ENDPROC() for 64bit-parisc
[PARISC] Fixes /proc/cpuinfo cache output on B160L
[PARISC] implement standard ENTRY(), END() and ENDPROC()
[PARISC] kill ENTRY_SYS_CPUS
[PARISC] clean up debugging printks in smp.c
[PARISC] factor syscall_restart code out of do_signal
...
Fix conflict in include/linux/sched.h due to kill_proc_info() being made
publicly available to PARISC again.
And remove it's reference in time.c.
Allow lcd_print() to take a const char *.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bug: pnx8550 code creates directory but resets ->nlink to 1.
create_proc_entry() et al will correctly set ->nlink for you.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Greg KH <greg@kroah.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix/change module_param permissions parameter from an init value
to a permission value.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Wilcox <willy@debian.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Run this:
#!/bin/sh
for f in $(grep -Erl "\([^\)]*\) *k[cmz]alloc" *) ; do
echo "De-casting $f..."
perl -pi -e "s/ ?= ?\([^\)]*\) *(k[cmz]alloc) *\(/ = \1\(/" $f
done
And then go through and reinstate those cases where code is casting pointers
to non-pointers.
And then drop a few hunks which conflicted with outstanding work.
Cc: Russell King <rmk@arm.linux.org.uk>, Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Ian Kent <raven@themaw.net>
Cc: Steven French <sfrench@us.ibm.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix up some PA-RISC work items broken by the workstruct reduction.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Firmware ignores Cardbus bridges, so when Linux assigns bus numbers,
it must override firmware's notion of what the busses are numbered.
This is not sufficient to support the Cardbus bridge as there is also
no interrupt routing table entry for them.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
This patch addresses the following issues:
* Removes an incorrect comment.
* Fixes a couple of compiler warnings.
* Properly detects the HP-PB bus on E-Class systems.
Signed-off-by: Ryan Bradetich <rbrad@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Fix various .c/.h typos in comments (no code changes).
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
Pull out struct sba_device and struct lba_device into a
common ropes.h header. Also fold the parisc portion of
iosapic.h into this file. (Then delete the useless portion
of iosapic.h)
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Our prior mode of operation didn't allow nested interrupts
because it makes the interrupt code much simpler. However,
nested interrupts are better for latency.
This code uses the EIEM register to simulate level interrupts
and thus achieve nesting.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Add header for McKinley bus related code. Remove extern decl
of proc_mckinley_root in drivers/parisc/sba_iommu.c
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Many files include the filename at the beginning, serveral used a wrong one.
Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
There are a few places in the kernel where the init task is signaled. The
ctrl+alt+del sequence is one them. It kills a task, usually init, using a
cached pid (cad_pid).
This patch replaces the pid_t by a struct pid to avoid pid wrap around
problem. The struct pid is initialized at boot time in init() and can be
modified through systctl with
/proc/sys/kernel/cad_pid
[ I haven't found any distro using it ? ]
It also introduces a small helper routine kill_cad_pid() which is used
where it seemed ok to use cad_pid instead of pid 1.
[akpm@osdl.org: cleanups, build fix]
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In some places, particularly drivers and __init code, the init utsns is the
appropriate one to use. This patch replaces those with a the init_utsname
helper.
Changes: Removed several uses of init_utsname(). Hope I picked all the
right ones in net/ipv4/ipconfig.c. These are now changed to
utsname() (the per-process namespace utsname) in the previous
patch (2/7)
[akpm@osdl.org: CIFS fix]
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Cc: Kirill Korotaev <dev@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: Andrey Savochkin <saw@sw.ru>
Cc: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use the new IRQF_ constants and remove the SA_INTERRUPT define
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The remaining counters in page_state after the zoned VM counter patches
have been applied are all just for show in /proc/vmstat. They have no
essential function for the VM.
We use a simple increment of per cpu variables. In order to avoid the most
severe races we disable preempt. Preempt does not prevent the race between
an increment and an interrupt handler incrementing the same statistics
counter. However, that race is exceedingly rare, we may only loose one
increment or so and there is no requirement (at least not in kernel) that
the vm event counters have to be accurate.
In the non preempt case this results in a simple increment for each
counter. For many architectures this will be reduced by the compiler to a
single instruction. This single instruction is atomic for i386 and x86_64.
And therefore even the rare race condition in an interrupt is avoided for
both architectures in most cases.
The patchset also adds an off switch for embedded systems that allows a
building of linux kernels without these counters.
The implementation of these counters is through inline code that hopefully
results in only a single instruction increment instruction being emitted
(i386, x86_64) or in the increment being hidden though instruction
concurrency (EPIC architectures such as ia64 can get that done).
Benefits:
- VM event counter operations usually reduce to a single inline instruction
on i386 and x86_64.
- No interrupt disable, only preempt disable for the preempt case.
Preempt disable can also be avoided by moving the counter into a spinlock.
- Handling is similar to zoned VM counters.
- Simple and easily extendable.
- Can be omitted to reduce memory use for embedded use.
References:
RFC http://marc.theaimsgroup.com/?l=linux-kernel&m=113512330605497&w=2
RFC http://marc.theaimsgroup.com/?l=linux-kernel&m=114988082814934&w=2
local_t http://marc.theaimsgroup.com/?l=linux-kernel&m=114991748606690&w=2
V2 http://marc.theaimsgroup.com/?t=115014808400007&r=1&w=2
V3 http://marc.theaimsgroup.com/?l=linux-kernel&m=115024767022346&w=2
V4 http://marc.theaimsgroup.com/?l=linux-kernel&m=115047968808926&w=2
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/kyle/parisc-2.6: (23 commits)
[PARISC] Move os_id_to_string() inside #ifndef __ASSEMBLY__
[PARISC] Fix do_gettimeofday() hang
[PARISC] Fix PCREL22F relocation problem for most modules
[PARISC] Refactor show_regs in traps.c
[PARISC] Add os_id_to_string helper
[PARISC] OS_ID_LINUX == 0x0006
[PARISC] Ensure Space ID hashing is turned off
[PARISC] Match show_cache_info with reality
[PARISC] Remove unused macro fixup_branch in syscall.S
[PARISC] Add is_compat_task() helper
[PARISC] Update Thibaut Varene's CREDITS entry
[PARISC] Reduce data footprint in pdc_stable.c
[PARISC] pdc_stable version 0.30
[PARISC] Work around machines which do not support chassis warnings
[PARISC] PDC_CHASSIS is implemented on all machines
[PARISC] Remove unconditional #define PIC in syscall macros
[PARISC] Use MFIA in current_text_addr on pa2.0 processors
[PARISC] Remove dead function pc_in_user_space
[PARISC] Test ioc_needs_fdc variable instead of open coding
[PARISC] Fix gcc 4.1 warnings in sba_iommu.c
...
This patch-queue improves the generic IRQ layer to be truly generic, by adding
various abstractions and features to it, without impacting existing
functionality.
While the queue can be best described as "fix and improve everything in the
generic IRQ layer that we could think of", and thus it consists of many
smaller features and lots of cleanups, the one feature that stands out most is
the new 'irq chip' abstraction.
The irq-chip abstraction is about describing and coding and IRQ controller
driver by mapping its raw hardware capabilities [and quirks, if needed] in a
straightforward way, without having to think about "IRQ flow"
(level/edge/etc.) type of details.
This stands in contrast with the current 'irq-type' model of genirq
architectures, which 'mixes' raw hardware capabilities with 'flow' details.
The patchset supports both types of irq controller designs at once, and
converts i386 and x86_64 to the new irq-chip design.
As a bonus side-effect of the irq-chip approach, chained interrupt controllers
(master/slave PIC constructs, etc.) are now supported by design as well.
The end result of this patchset intends to be simpler architecture-level code
and more consolidation between architectures.
We reused many bits of code and many concepts from Russell King's ARM IRQ
layer, the merging of which was one of the motivations for this patchset.
This patch:
rename desc->handler to desc->chip.
Originally i did not want to do this, because it's a big patch. But having
both "desc->handler", "desc->handle_irq" and "action->handler" caused a
large degree of confusion and made the code appear alot less clean than it
truly is.
I have also attempted a dual approach as well by introducing a
desc->chip alias - but that just wasnt robust enough and broke
frequently.
So lets get over with this quickly. The conversion was done automatically
via scripts and converts all the code in the kernel.
This renaming patch is the first one amongst the patches, so that the
remaining patches can stay flexible and can be merged and split up
without having some big monolithic patch act as a merge barrier.
[akpm@osdl.org: build fix]
[akpm@osdl.org: another build fix]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a helper to asm/pdc.h to translate OS_ID values to strings
and use it in the pdc_stable driver.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
We were assigned an OS_ID of 0x0006. Consistently use OS_ID_LINUX
instead of using the magic number. Also update the OS_ID_ defines in
asm/pdc.h to reflect this.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
pdc_stable v0.30:
This patch introduces 3 more files to the /sys/firmware/stable tree:
- diagnostic, which contains a cryptic hex string
- osdep1, a 16 bytes os-dependent storage area always available
- osdep2, another os-dependent storage area which existence/size depends
on hversion.
This patch also adds code to setup the "Linux" signature in stable
storage. That is to say that starting with this patch, the kernel will
now sign its OSID (0x0006, thx LaMont) in Stable Storage upon boot,
whether pdc_stable is enabled or not.
Signed-off-by: Thibaut VARENE <varenet@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
This patch removes a limitation of the original code, so that CHASSIS
codes can be sent to all machines. On machines with a LCD panel, this
code displays "INI" during bootup, "RUN" when the system is booted and
running, "FLT" when a panic occurs, etc.
This part of the code can be enabled/disabled through CONFIG_PDC_CHASSIS
This patch also adds minimalistic support for Chassis warnings, through
a proc entry '/proc/chassis', which will reflect the warnings status (PSU
or fans failure when they happen, NVRAM battery level and temperature
thresholds overflows).
This part of the code can be enabled/disabled through CONFIG_PDC_CHASSIS_WARN
Signed-off-by: Thibaut VARENE <varenet@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Some debugging code in sba_iommu.c should be testing ioc_needs_fdc,
not directly testing boot_cpu_data.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Clean up gcc 4.1 warnings noted by Joel Soete.
Kyle McMartin gets kudos for pointing out the issues.
Matthew Wilcox noticed sba_iommu was using open coded versions
of (read|write)X.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
This means "DMA Read returns" can bypass "MMIO Writes".
Violating the PCI specs in this case improves outbound DMA "flows"
and is currently not required by any drivers.
This is NOT a new behavior. Previous chipsets did this
already and I believe ZX1 PDC was already setting this
for hpux. I just want to further document the behavior.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Addresses in F-space must be accessed uncached on most parisc machines.
Signed-off-by: Helge Deller <deller@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
The kernel's implementation of notifier chains is unsafe. There is no
protection against entries being added to or removed from a chain while the
chain is in use. The issues were discussed in this thread:
http://marc.theaimsgroup.com/?l=linux-kernel&m=113018709002036&w=2
We noticed that notifier chains in the kernel fall into two basic usage
classes:
"Blocking" chains are always called from a process context
and the callout routines are allowed to sleep;
"Atomic" chains can be called from an atomic context and
the callout routines are not allowed to sleep.
We decided to codify this distinction and make it part of the API. Therefore
this set of patches introduces three new, parallel APIs: one for blocking
notifiers, one for atomic notifiers, and one for "raw" notifiers (which is
really just the old API under a new name). New kinds of data structures are
used for the heads of the chains, and new routines are defined for
registration, unregistration, and calling a chain. The three APIs are
explained in include/linux/notifier.h and their implementation is in
kernel/sys.c.
With atomic and blocking chains, the implementation guarantees that the chain
links will not be corrupted and that chain callers will not get messed up by
entries being added or removed. For raw chains the implementation provides no
guarantees at all; users of this API must provide their own protections. (The
idea was that situations may come up where the assumptions of the atomic and
blocking APIs are not appropriate, so it should be possible for users to
handle these things in their own way.)
There are some limitations, which should not be too hard to live with. For
atomic/blocking chains, registration and unregistration must always be done in
a process context since the chain is protected by a mutex/rwsem. Also, a
callout routine for a non-raw chain must not try to register or unregister
entries on its own chain. (This did happen in a couple of places and the code
had to be changed to avoid it.)
Since atomic chains may be called from within an NMI handler, they cannot use
spinlocks for synchronization. Instead we use RCU. The overhead falls almost
entirely in the unregister routine, which is okay since unregistration is much
less frequent that calling a chain.
Here is the list of chains that we adjusted and their classifications. None
of them use the raw API, so for the moment it is only a placeholder.
ATOMIC CHAINS
-------------
arch/i386/kernel/traps.c: i386die_chain
arch/ia64/kernel/traps.c: ia64die_chain
arch/powerpc/kernel/traps.c: powerpc_die_chain
arch/sparc64/kernel/traps.c: sparc64die_chain
arch/x86_64/kernel/traps.c: die_chain
drivers/char/ipmi/ipmi_si_intf.c: xaction_notifier_list
kernel/panic.c: panic_notifier_list
kernel/profile.c: task_free_notifier
net/bluetooth/hci_core.c: hci_notifier
net/ipv4/netfilter/ip_conntrack_core.c: ip_conntrack_chain
net/ipv4/netfilter/ip_conntrack_core.c: ip_conntrack_expect_chain
net/ipv6/addrconf.c: inet6addr_chain
net/netfilter/nf_conntrack_core.c: nf_conntrack_chain
net/netfilter/nf_conntrack_core.c: nf_conntrack_expect_chain
net/netlink/af_netlink.c: netlink_chain
BLOCKING CHAINS
---------------
arch/powerpc/platforms/pseries/reconfig.c: pSeries_reconfig_chain
arch/s390/kernel/process.c: idle_chain
arch/x86_64/kernel/process.c idle_notifier
drivers/base/memory.c: memory_chain
drivers/cpufreq/cpufreq.c cpufreq_policy_notifier_list
drivers/cpufreq/cpufreq.c cpufreq_transition_notifier_list
drivers/macintosh/adb.c: adb_client_list
drivers/macintosh/via-pmu.c sleep_notifier_list
drivers/macintosh/via-pmu68k.c sleep_notifier_list
drivers/macintosh/windfarm_core.c wf_client_list
drivers/usb/core/notify.c usb_notifier_list
drivers/video/fbmem.c fb_notifier_list
kernel/cpu.c cpu_chain
kernel/module.c module_notify_list
kernel/profile.c munmap_notifier
kernel/profile.c task_exit_notifier
kernel/sys.c reboot_notifier_list
net/core/dev.c netdev_chain
net/decnet/dn_dev.c: dnaddr_chain
net/ipv4/devinet.c: inetaddr_chain
It's possible that some of these classifications are wrong. If they are,
please let us know or submit a patch to fix them. Note that any chain that
gets called very frequently should be atomic, because the rwsem read-locking
used for blocking chains is very likely to incur cache misses on SMP systems.
(However, if the chain's callout routines may sleep then the chain cannot be
atomic.)
The patch set was written by Alan Stern and Chandra Seetharaman, incorporating
material written by Keith Owens and suggestions from Paul McKenney and Andrew
Morton.
[jes@sgi.com: restructure the notifier chain initialization macros]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
this changes if() BUG(); constructs to BUG_ON() which is
cleaner, contains unlikely() and can better optimized away.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Use seq_file interface for proc output in sba_iommu. Also
clean up the bus root assignment, and give the proc files
a more logical name. Tested on my J6000.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Gut ccio-dma.c of the ugly proc append and snprintf cruft and
just use seq_printf instead. Tested on a K-class.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Clean up some of the messages printed by the superio driver
by defining a prefix instead of duplicating it in every message.
Also some small coding style cleanups.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Define a chassis_power_off routine that machines which have a way
to turn off the power supply can hook into. Formerly they were
using pm_power_off, which is now being used by generic code. Make
lasi.c use chassis_power_off instead of pm_power_off.
Note, all machines need to call machine_power_off so that the
switch can power off the machine, though halt -p may not necessarily
be able to work properly on the machine.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
pdc_stable v0.22, changes since v0.10:
o renamed root subsystem from 'pdc' to 'stable'
o split 'info' into several files, one per PDC field
o implemented 'autoboot' and 'autosearch' write calls to toggle
these flags
o grant read permission to all users on "safe" files
o more code cleanup (removed duplicate code)
o avoid bad stable storage clobbering by write locking critical sections
o print consistent data as well
o SMP cleanups
Signed-off-by: Thibaut VARENE <varenet@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Helge,
o Convert a bunch of kmalloc/memset uses to kzalloc.
o pci.c: Add some __read_mostly annotations.
o pci.c: Move constant pci_post_reset_delay to asm/pci.h
o grfioctl.h: Add A4450A to comment of CRT_ID_VISUALIZE_EG.
o Add some consts to perf.c/perf_images.h
Matthew,
o sticore.c: Add some consts to suppress compile warnings.
Signed-off-by: Helge Deller <deller@parisc-linux.org>
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
- Move capable() from sched.h to capability.h;
- Use <linux/capability.h> where capable() is used
(in include/, block/, ipc/, kernel/, a few drivers/,
mm/, security/, & sound/;
many more drivers/ to go)
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix Dino reporting on J2240. This particular machine thought it
had a Cujo. Also add J2240 Dino chip to the hp_hardware_list.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
pdc_stable 0.10:
As mentioned on LKML, pdc_stable wasn't checky enough on the return
values of some calls. This patch makes it more robust to errors when
registering objects in sysfs.
Signed-off-by: Thibaut VARENE <varenet@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Deal with overlapping LBA MMIO resources,
rp3440 PDC BUG: PDC reports lmmio range for the last rope that overlaps
with the CPU HPA. Console output was:
...
Found devices:
1. Storm Peak Fast at 0xfffffffffe798000 [152] { 0, 0x0, 0x889, 0x00004 }
2. Storm Peak Fast at 0xfffffffffe799000 [153] { 0, 0x0, 0x889, 0x00004 }
...
FAILED: lba_fixup_bus() request for lmmio_space
[fffffffff0000000/fffffffffecffffe]
Output is now:
LBA: Truncating lmmio_space [fffffffff0000000/fffffffffecffffe] to
[fffffffff0000000,fffffffffe797fff]
My only concern with this patch is how C8000 (PAT PDC) will report
elmmio ranges when a gfx card is installed. I'll have to test this
another day.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: James Bottomley <jejb@parisc-linux.org>
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Fix dino by using DINO_LOCAL_IRQS as the limit for gsc_find_local_irq()
instead of the irq itself.
Signed-off-by: Helge Deller <deller@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Fix irq-off-by-one for Cirrus 6832 Cardbus on RDI Tadpole PARISC Laptop.
We just DECLARE_PCI_FIXUP_ENABLE as it is unlikely that this will be
found in any other parisc system.
Signed-off-by: Helge Deller <deller@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Flag a whole bunch of things as __read_mostly on parisc. Also flag a few
branches as unlikely() and cleanup a bit of code.
Signed-off-by: Helge Deller <deller@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Convert superio_init to use PCI_FIXUP_FINAL as ohci_pci being called
before superio_probe really makes a mess. superio_init will then fail
to register irq 20 (the "SuperIO" irq) and BUG() because ohci_pci has
stolen it before superio_fixup_irq can be moved USB to irq 1.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
This really only adds them for the machines I can check SMP on, which
is CPU interrupts and IOSAPIC (so not any of the GSC based machines).
With this patch, irqbalanced can be used to maintain irq balancing.
Unfortunately, irqbalanced is a bit x86 centric, so it doesn't do an
incredibly good job, but it does work.
Signed-off-by: James Bottomley <jejb@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
git commit 976ecd12b8 changed our locking
characteristics, and put the onus of spin_lock_init on superio.c.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
2.6.12-rc1-pa6 use work queue in LED/LCD driver instead of tasklet.
Main advantage is it allows use of msleep() in the led_LCD_driver to
"atomically" perform two MMIO writes (CMD, then DATA).
Lead to nice cleanup of the main led_work_func() and led_LCD_driver().
Kudos to David for being persistent.
From: David Pye <dmp@davidmpye.dyndns.org>
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Fix card-mode Dino crashes on 725 (and probably other Snake) systems.
Dino was coming up in fatal mode after a warm reboot. Resetting Dino
brings it out of fatal mode, so do that if the status register indicates
we're in fatal mode. Since this was never observed on any later systems,
I presume firmware does this for us on those.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Add debug statements in the cfg_read and cfg_write functions
Fix debug statements from the IRQ overhaul last winter
Rename dino_driver_callback() to dino_probe()
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
revert use of %%sr0 in fdc asm.
Thanks to Joel Soete for pointing out this oversight.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
2.6.14-rc2-pa3 fdc/lci should be %r0 instead 0 for index (PA 1.1 compliance)
From: Joel Soete <soete.joel@tiscali.be>
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Explain why we need insert_resource() instead of request_resource().
Fundementally, this is more convoluted for ccio driver because of
o legacy (HP-PB) transperant bridges.
o support for MMIO behind card-mode Dino (PCI)
o support for above bridges without ccio in the box
SBA driver doesn't have to worry about those issues.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Use insert_resource instead of request_resource now that the subdevices
will already have their resources claimed
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
re-enable use of "inline" for perf critical functions.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
2.6.12-rc4-pa5 fix sign extension of MMIO range
Fixes the problem of claiming a range that is disabled on 64-bit kernel:
ccio_init_resource() claimed CCIO bus address space (ffffffff00000000,
ffffffffffffffff)
also removes use of __FILE__.
Tested on both 32 and 64-bit systems by Joel.
From: Joel Soete <soete.joel@tiscali.be>
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
2.6.12-rc1-pa7 incorrect BUG_ON in ccio
ccio-dma.c line 1317 was preventing K-class with 4GB RAM from booting.
Any ccio machine with >=2GB of RAM would have (incorrectly) triggered this.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Convert to ioremap and __raw_read/write
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
revert use of %%sr0 in fdc asm.
Thanks to Joel Soete for pointing out this oversight.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
2.6.14-rc2-pa3 move "sync" outside the main loop that fills IO Pdir.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
remove explicit use of sr0 in fdc ops.
Thanks to Joel Soete for reminding me were I added those...
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
2.6.14-rc2-pa2 - make SBA more anal about invalidating pdir entries
Previous code cleared the valid flag a pdir entry but it did NOT
guarantee this change was visible to the PDIR before writing
the PCOM register. Ie the SBA could pick up a stale entry if
the write happened to hit the SBA before the cacheline was flushed
from the cache.
Long term, I think I want to make this a compile time flag.
Developement tree should enable anal pdir checking by default
and Debian can disable it with either a CONFIG option
or one-line patch. fdc/sync options can only negatively affect
performance though I haven't measure how much yet.
If someone can run netperf TCP_RR across gige and compare
-pa1 and -pa2, that would be sufficient.
Cleaned up the use of "fdc" to make sure it's using "kernel"
space id (specify sr0 but maps to sr4-7). It seems a bit fragile
to assume "sr1" gets loaded with KERNEL_SPACE which is how the
code works today.
Tested on 32 and 64-bit SMP kernels on j6k.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
remove PDC_NARROW from SBA and document history of PDC_NARROW a bit.
It will still show up in an older kernel's .config file.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
if/ifdef cleanups from Joel Soete.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
2.6.12-rc4-pa2 fix 32-bit support for Astro platforms
o Since my last SBA code change, SBA could allocate more than 1GB of IOVA
space on Astro boxes with more than 1GB of RAM when running 32-bit kernel.
This is bad since IOMMU can only talk to the first 1GB at most.
Kudos to jejb for quickly spotting that bug.
o jejb also noted SBA should *always* reject DMA masks > 32-bits since
DMA-mapping.txt indicates caller should try again with 32-bits.
o off-by-one error when comparing the mask to IOVA space size.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Convert pa_dev->hpa from an unsigned long to a struct resource.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Fix up users of ->hpa to use ->hpa.start instead.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Make /sys/bus/parisc/drivers look better by cleaning up parisc_driver
names.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Fix parse_tree_node. much more needs to be done to fix this file.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Make drivers.c compile based on a patch from Pat Mochel.
From: Patrick Mochel <mochel@digitalimplant.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Fix drivers.c to create new device tree nodes when no match is found.
Signed-off-by: Richard Hirst <rhirst@parisc-linux.org>
Do a proper depth-first search returning parents before children, using the
new klist infrastructure.
Signed-off-by: Richard Hirst <rhirst@parisc-linux.org>
Fixed parisc_device traversal so that pdc_stable works again
Fixed check_dev so it doesn't dereference a parisc_device until it
has verified the bus type
Signed-off-by: Randolph Chung <tausq@parisc-linux.org>
Convert pa_dev->hpa from an unsigned long to a struct resource.
Use insert_resource() instead of request_mem_region().
Request resources at bus walk time instead of driver probe time.
Don't release the resources as we don't have any hotplug parisc_device
support yet.
Add parisc_pathname() to conveniently get the textual representation
of the hwpath used in sysfs.
Inline the remnants of claim_device() into its caller.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
I noticed that some of the STI regions weren't showing up in iomem.
Reading the STI spec indicated that all STI devices occupy at least 32MB.
So check for STI HPAs and give them 32MB instead of 4kB.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Grant Grundler