This adds support for the AU Optronics G185HAN01 18.5" LVDS FullHD TFT
LCD panel, which can be supported by the simple panel driver.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This adds support for the AU Optronics G133HAN01 13.3" LVDS FullHD TFT
LCD panel, which can be supported by the simple panel driver.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Convert from a single mode to display timings, which allow to describe
the minimum/maximium blanking and clock rates, add enable/disable delays
and provide the bus format.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Sharp LQ123P1JX31 panel support 8 bits per component.
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In the loop on .timings, we should check .num_timings to see if it's the
only mode specified, not .num_modes, which should be used with .modes.
Fixes: cda553725c ("drm/panel: simple: Set appropriate mode type")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Chunghwa CLAA070WP03XG is a 7" 1280x800 panel, which can be
supported by the simple panel driver.
Signed-off-by: Randy Li <ayaka@soulik.info>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The AUO T215HVN01 is a 21.5" FHD (1920x1080) color TFT LCD panel.
This panel is used on the Acer Chromebase 21.5-inch All-in-One (DC221HQ).
Link to spec: http://www.udmgroup.com/ftp/T215HVN01.0.pdf
v2: fix alphabetical order
v3: remove minor revision suffix ".0" and add link to spec
v4: add dt-binding documentation
Signed-off-by: Haixia Shi <hshi@chromium.org>
Tested-by: Haixia Shi <hshi@chromium.org>
Reviewed-by: Stéphane Marchesin <marcheu@chromium.org>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Sharp 15" LQ150X1LG11 panel is an XGA TFT LCD panel.
The simple-panel driver is used to get support for essential
functionality of the panel.
Signed-off-by: Gustaf Lindström <gl@axentia.se>
Signed-off-by: Peter Rosin <peda@axentia.se>
[treding@nvidia.com: change .bpc from 8 to 6]
Signed-off-by: Thierry Reding <treding@nvidia.com>
The format is RGB888 not RGB666.
Signed-off-by: Jonathan Liu <net147@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Taking our cue from commit a42f6e3f8f ("drm/panel: simple: Add delay
timing for Sharp LQ123P1JX31"), let's add timings:
.prepare = t1 + t3
.enable = t7
.unprepare = t11 + 12
Without this, the panel may not be given enough time to come up.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This display expects DE pin and data lines to be active high, add the
necessary flags.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Thierry Reding <treding@nvidia.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch adds support for Innolux Corporation 10.1" G101ICE-L01 WXGA
(1280x800) LVDS panel to the simple-panel driver.
Signed-off-by: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
According to page 16 of the Sharp LQ123P1JX31 datasheet, we need to add
the missing delay timing. Panel prepare time should be t1 (0.5 to 10 ms)
plus t3 (0 to 100 ms), panel enable time should equal to t7 (0 to 50 ms)
and panel unprepare time should be t11 (1 to 50 ms) plus t12 (500 ms).
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add simple-panel support for the Sharp LQ101K1LY04, which is a 10"
WXGA (1280x800) LVDS panel.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The LG LP079QX1-SP0V is an 7.9" QXGA TFT with LED Backlight unit and
32 pins eDP interface. This module supports 1536x2048 mode.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Sharp LQ123P1JX31 is an 12.3", 2400x1600 TFT-LCD panel connected
using eDP interfaces.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Samsung LSN122DL01-C01 is an 12.2" 2560x1600 (WQXGA) TFT-LCD panel
connected using eDP interfaces.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The LG LP097QX1-SPA1 is an 9.7", 2048x1536 (QXGA) TFT-LCD panel
connected using eDP interfaces.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Some backlight drivers ignore the power property and instead only use
the state property. Fixup the panel driver to set the state property in
addition to the power property.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This blank line was introduced in commit c8521969de ("drm/panel:
simple: Add support for BOE TV080WUM-NL0"), likely by mistake.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Both the Innolux ZJ070NA-01P and Samsung LTN101NT05 were listing the
horizontal and vertical resolutions in the size.width and size.height
fields, whereas they should contain the physical dimensions of the
panel.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for TPK U.S.A. LLC Fusion 7", 10.1" panels to the DRM simple
panel driver.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for the Innolux AT070TN92 panel.
Signed-off-by: Riccardo Bortolato <bortolato@navaltechitalia.it>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
All modes exposed by simple panels should be tagged as driver defined
modes. Moreover, if a panel supports only one mode, this mode is
obviously the preferred one.
Doing this also fix a problem occurring when a 'video=' parameter is
passed on the kernel command line. In some cases the user provided mode
will be preferred over the simple panel ones, which might result in
unpredictable behavior.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Nicolas Ferre <nicolas.ferre@atmel.com>
[treding@nvidia.com: reshuffle some code for consistency]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for the Olimex LCD-OLinuXino-4.3TS panel to the DRM simple
panel driver.
It is a 480x272 panel connected through a 24-bits RGB interface.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This is a basic TFT panel with a 40-pin FPC connector on it. The
specification doesn't define timings, but the Adafruit instructions
were setting up 800x480 CVT.
v2: Add .bus_format and vsync/hsync flags.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Rob Herring <robh@kernel.org>
[treding@nvidia.com: keep entries properly sorted]
Signed-off-by: Thierry Reding <treding@nvidia.com>
The drivers current default configuration drives the pixel data
on rising edge of the pixel clock. However, most display sample
data on rising edge... This leads to color shift artefacts visible
especially at edges.
This patch changes the relevant defines to be useful and actually
set the bits, and changes pixel clock polarity to drive the pixel
data on falling edge by default. The patch also adds an explicit
pixel clock polarity flag to the display introduced with the driver
(NEC WQVGA "nec,nl4827hc19-05b") using the new bus_flags field to
retain the initial behavior.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Introduce bus_flags to specify display bus properties like signal
polarities. This is useful for parallel display buses, e.g. to
specify the pixel clock or data enable polarity.
Suggested-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Manfred Schlaegl <manfred.schlaegl@gmx.at>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Stefan Agner <stefan@agner.ch>
This contains a refactoring of parts of the DSI core to allow creating
DSI devices from non-DSI control busses (i.e. I2C, SPI, ...).
Other than that there's support for a couple of new panels as well as
a few cleanup patches.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=zrRb
-----END PGP SIGNATURE-----
Merge tag 'drm/panel/for-4.6-rc1' of http://anongit.freedesktop.org/git/tegra/linux into drm-next
drm/panel: Changes for v4.6-rc1
This contains a refactoring of parts of the DSI core to allow creating
DSI devices from non-DSI control busses (i.e. I2C, SPI, ...).
Other than that there's support for a couple of new panels as well as
a few cleanup patches.
* tag 'drm/panel/for-4.6-rc1' of http://anongit.freedesktop.org/git/tegra/linux:
drm/bridge: Make (pre/post) enable/disable callbacks optional
drm/panel: simple: Add URT UMSH-8596MD-xT panels support
dt-bindings: Add URT UMSH-8596MD-xT panel bindings
of: Add United Radiant Technology Corporation vendor prefix
drm/panel: simple: Support for LG lp120up1 panel
dt-bindings: Add LG lp120up1 panel bindings
drm/panel: simple: Fix g121x1_l03 hsync/vsync polarity
drm/dsi: Get DSI host by DT device node
drm/dsi: Add routine to unregister a DSI device
drm/dsi: Try to match non-DT DSI devices
drm/dsi: Use mipi_dsi_device_register_full() for DSI device creation
drm/dsi: Check for CONFIG_OF when defining of_mipi_dsi_device_add()
Add support for United Radiant Technology UMSH-8596MD-xT 7.0" WVGA TFT
LCD panels in the simple-panel driver.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The LG lp120up1 TFT LCD panel with eDP interface is a 12.0" 1920x1280
panel, which can be supported by the simple panel driver.
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Set hsync/vsync to active low for g121x1_l03 panel to match the
recommended setting in the datasheet.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The current default configuration is as follows:
- Invert VSYNC signal (active LOW)
- Invert HSYNC signal (active LOW)
The mode flags allow to specify the required polarity per
mode. Furthermore, none of the current driver settings is
actually a standard polarity.
This patch applies the current driver default polarities as
explicit flags to the display which has been introduced with
the driver (NEC WQVGA "nec,nl4827hc19-05b"). The driver now
also parses the flags field and applies the configuration
accordingly, by using the following values as standard
polarities: (e.g. when no flags are specified):
- VSYNC signal not inverted (active HIGH)
- HSYNC signal not inverted (active HIGH)
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Document that 'width' and 'height' are measured in millimeters.
Signed-off-by: Ulrich Ölmann <u.oelmann@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Kyocera TCG121XGLP panel is an XGA LCD TFT panel connected through
LVDS, which can be supported by the simple panel driver.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The BOE TV080WUM-NL0 is an 8.0", 1200x1920 (WUXGA) TFT-LCD panel
connected using four DSI lanes. It can be supported by the simple-panel
driver.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for the Okaya RS800480T-7X0GP to the DRM simple panel
driver.
The RS800480T-7X0GP is a WVGA (800x480) panel with an 18-bit parallel
LCD interface. It supports pixel clocks in the range of 30-40 MHz.
This panel details can be found at:
http://boundarydevices.com/product/7-800x480-display/
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This adds support for the NEC NL4827HC19-05B 480x272 panel to the DRM
simple panel driver.
Signed-off-by: Alison Wang <b18965@freescale.com>
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Jianwei Wang <jianwei.wang.chn@gmail.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[treding@nvidia.com: add .bpc field for panel]
Signed-off-by: Thierry Reding <treding@nvidia.com>
The AUO B080UAN01 is an 8.0" WUXGA TFT LCD panel connected using four
DSI lanes. It can be supported by the simple-panel driver.
Signed-off-by: Thierry Reding <treding@nvidia.com>
According to the data sheet, the minimum horizontal blanking interval
is 54 clocks (1 + 52 + 1), but tests with a Nitrogen6X have shown the
minimum working horizontal blanking interval to be 60 clocks.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The bus format both specifies the bpc and the way the individual bits get
serialized into the 7 LVDS timeslots.
While the is only one standard mapping for 6 bpc and so the driver could
infer the bit mapping from the bpc alone, there are more options for the
8 bpc case which makes specifiying the bus format mandatory.
To keep things consistent across panels and to set a precedent for new
panel additions add the proper bus format.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch adds the bus_format field to the HSD100PXN1 panel structure.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for the Hannstar HSD100PXN1 to the DRM simple panel driver.
The HSD100PXN1 is an XGA (1024x768) panel with an 18-bit LVDS interface.
It supports pixel clocks in the range of 55-75 MHz.
This panel is offered for sale by Freescale as a companion part to its'
i.MX5x Quick Start board and i.MX6 SABRE platforms with under the name
MCIMX-LVDS1.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This adds support for the LG LB070WV8 7" 800x480 panel to the DRM simple
panel driver.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This adds support for the AM-800480R3TMQW-A1H 7" 800x480 panel to the
DRM simple panel driver.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The HannStar HSD070PWW1 LVDS panel data sheet lists allowed ranges
additionally to the typical values for pixel clock rate (64.3-82 MHz)
and blanking intervals (54-681 clock cycles horizontally, 3-23 lines
vertically).
This patch replaces this panel's display mode with the display timing
information to describe acceptable timings. Since the HSYNC and VSYNC
are unused, the distribution between front porches, back porches, and
sync pulse lengths was chosen at will.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The simple panel driver's ->get_modes() implementation calculates the
display mode list from the typical timings and the ->get_timings()
implementation returns the timings to the connected encoder for mode
validation and fixup.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
[treding@nvidia.com: select VIDEOMODE_HELPERS]
Signed-off-by: Thierry Reding <treding@nvidia.com>
This adds support for the COM43H4M85ULC 3.7" 800x480 panel to the
DRM simple panel driver.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch adds the bus_format field to the GPG482739QS5 panel structure.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The AUO b101ean01 panel is a 10.1" 1280x800 panel which can be supported
by the simple panel driver.
Signed-off-by: Huang Lin <hl@rock-chips.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Innolux ZJ070NA-01P is a 7.0" TFT LCD panel with an integrated LED
backlight unit.
This panel is used on the Technexion Toucan.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Innolux AT043TN24 4.3" WQVGA TFT LCD panel.
This panel with backlight is found in PDA 4.3" LCD screen (TM43xx series for
instance).
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Shelly SCA07010-BFN-LNN is a 7.0" WVGA TFT LCD panel.
This panel with backlight is found in PDA 7" LCD screen (TM70xx series for
instance).
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This panel is used by the Nyan Blaze board and can be supported by the
simple-panel driver.
Signed-off-by: Stéphane Marchesin <marcheu@chromium.org>
[tomeu.vizoso@collabora.com: add device tree binding document]
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Shanghai AVIC Optoelectronics TM070DDH03 is a 7" 1024x600 TFT LCD
panel connecting to a 24-bit RGB LVDS interface.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch adds support for the GiantPlus GPG48273QS5 4.3" WQVGA TFT LCD
panel to the simple-panel driver.
This panel is connected via a parallel bus and uses both HSYNC and
VSYNC, whose lengths are unfortunately not clearly defined. The
datasheet only specifies the front- and backporch length, but the timing
diagram suggests that both sync signals should be asserted for exactly
one clock cycle.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Provide a way to specify panel requirement in terms of supported media bus
format (particularly useful for panels connected to an RGB or LVDS bus).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Pull drm updates from Dave Airlie:
"Highlights:
- AMD KFD driver merge
This is the AMD HSA interface for exposing a lowlevel interface for
GPGPU use. They have an open source userspace built on top of this
interface, and the code looks as good as it was going to get out of
tree.
- Initial atomic modesetting work
The need for an atomic modesetting interface to allow userspace to
try and send a complete set of modesetting state to the driver has
arisen, and been suffering from neglect this past year. No more,
the start of the common code and changes for msm driver to use it
are in this tree. Ongoing work to get the userspace ioctl finished
and the code clean will probably wait until next kernel.
- DisplayID 1.3 and tiled monitor exposed to userspace.
Tiled monitor property is now exposed for userspace to make use of.
- Rockchip drm driver merged.
- imx gpu driver moved out of staging
Other stuff:
- core:
panel - MIPI DSI + new panels.
expose suggested x/y properties for virtual GPUs
- i915:
Initial Skylake (SKL) support
gen3/4 reset work
start of dri1/ums removal
infoframe tracking
fixes for lots of things.
- nouveau:
tegra k1 voltage support
GM204 modesetting support
GT21x memory reclocking work
- radeon:
CI dpm fixes
GPUVM improvements
Initial DPM fan control
- rcar-du:
HDMI support added
removed some support for old boards
slave encoder driver for Analog Devices adv7511
- exynos:
Exynos4415 SoC support
- msm:
a4xx gpu support
atomic helper conversion
- tegra:
iommu support
universal plane support
ganged-mode DSI support
- sti:
HDMI i2c improvements
- vmwgfx:
some late fixes.
- qxl:
use suggested x/y properties"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (969 commits)
drm: sti: fix module compilation issue
drm/i915: save/restore GMBUS freq across suspend/resume on gen4
drm: sti: correctly cleanup CRTC and planes
drm: sti: add HQVDP plane
drm: sti: add cursor plane
drm: sti: enable auxiliary CRTC
drm: sti: fix delay in VTG programming
drm: sti: prepare sti_tvout to support auxiliary crtc
drm: sti: use drm_crtc_vblank_{on/off} instead of drm_vblank_{on/off}
drm: sti: fix hdmi avi infoframe
drm: sti: remove event lock while disabling vblank
drm: sti: simplify gdp code
drm: sti: clear all mixer control
drm: sti: remove gpio for HDMI hot plug detection
drm: sti: allow to change hdmi ddc i2c adapter
drm/doc: Document drm_add_modes_noedid() usage
drm/i915: Remove '& 0xffff' from the mask given to WA_REG()
drm/i915: Invert the mask and val arguments in wa_add() and WA_REG()
drm: Zero out DRM object memory upon cleanup
drm/i915/bdw: Fix the write setting up the WIZ hashing mode
...
Drivers now no longer need to set the .owner field. It will be
automatically set at registration time.
Signed-off-by: Thierry Reding <treding@nvidia.com>
There are several different models of N116BGE. According to commit
0a2288c06a ("drm/panel: simple: Add Innolux N116BGE panel support"),
the video timings are for the eDP variant.
The clock and htotal values added by that patch are out of spec
according to the datasheets I have seen for the eDP N116BGE (-EA2 and
-EB2).
This patch changes the values to the "Typ" values on the datasheet.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
[tested that these timings work with the Tegra132 Norrin panel]
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Hitachi TX23D38VM0CAA is a 9" WVGA TFT LCD panel and can be
supported by the simple-panel driver.
This panel is connected via LVDS and uses the data enable signal for
timing. Since HSYNC/VSYNC are ignored, the split between sync length and
porches is arbitrary, as long as the complete horizontal blanking interval
is 256 clocks, and the vertical blanking interval is 45 lines.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Innolux G121I1-L01 is a 12.1" TFT LCD panel and can be supported by
the simple-panel driver.
This panel is connected via LVDS and uses the data enable signal for
timing. Since HSYNC/VSYNC are ignored, the split between sync length and
porches is arbitrary, as long as the complete horizontal blanking interval
is 160 clocks, and the vertical blanking interval is 24 lines.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Various panels were missing the .bpc field which encodes the number of
bits per color. Not every display driver relies on this value, but since
the panels can be used with any display engine it must be specified so
that if a driver knows how to differentiate based on this field it can
do so.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The AUO B116XW03 is a 11.6" HD TFT LCD panel connecting to a LVDS
interface and with an integrated LED backlight unit.
This panel is used on the Samsung Chromebook(XE303C12).
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
[treding@nvidia.com: add missing .bpc field]
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch adds support for the HannStar Display Corp. HSD070PWW1 7.0"
WXGA TFT LCD panel to the simple-panel driver. The binding documentation
is included.
This panel is connected via LVDS and uses the data enable signal for
timing. Since HSYNC/VSYNC are ignored, the split between sync length and
porches is arbitrary, as long as the complete horizontal blanking interval
is 160 clocks, and the vertical blanking interval is 23 lines.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the new flags argument to calls of (devm_)gpiod_get*() and remove
any direction setting code afterwards.
Currently both forms (with or without the flags argument) are valid
thanks to transitional macros in <linux/gpio/consumer.h>. These macros
will be removed once all consumers are updated and the flags argument
will become compulsary.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
LVDS panel, make/model described as:
AU Optronics Corporation - B101XTN01.0 (H/W:0A)
See:
http://www.encore-electronic.com/media/B101XTN01.0.pdf
Tested with panel attached to an Inforce IFC6410 board.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Use the new devm_gpiod_get_optional() to simplify the probe code.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The AUO B133HTN01 is a 13.6" FHD TFT LCD panel connecting to an eDP
interface and with an integrated LED backlight unit.
This panel is used on the Samsung Chromebook 2 (XE503C32).
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
For most of the panels, we need to provide delays during various stages
of panel power up and power down. Add a structure to hold those delay
values and use them in corresponding functions.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Move out code from enable and disable routines to prepare
and unprepare routines, so that functionality is properly
distributed across all the panel functions.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
simple-panel is not a valid panel model, so there is no data (video
timings, etc.) associated with it. Therefore drivers can't do anything
useful with it, so it should not appear in the table of OF matches.
Device trees will always need to specify the exact model of the panel.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Innolux N116BGE is an 11.6" WXGA TFT LCD panel connecting to an eDP
interface and with an integrated LED backlight unit.
It is used in the Tegra132 Norrin reference design.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The bits-per-color is provided by the EDID normally, but if we're using
panels, we need to store it somewhere. So we add a field to the panel
descriptor for it.
Signed-off-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This panel is used by the Medcom Wide and supported by the
simple-panel driver.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This panel is used by Atmel's SAMA5D3 Evaluation Kits (sama5d3xek) and
supported by the simple-panel driver.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The LG LD070WX3-SL01 and Panasonic VVX10F004B00 are DSI support
non-continuous clock mode. Set the MIPI_DSI_CLOCK_NON_CONTINUOUS
to their definition so host drivers become aware of this capability.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This panel is used by nyan-big and can be supported by the simple-panel
driver.
Signed-off-by: Stéphane Marchesin <marcheu@chromium.org>
[treding@nvidia.com: add device tree binding document]
Signed-off-by: Thierry Reding <treding@nvidia.com>
This panel is sold by Toradex for Colibri T20/T30 and Apalis T30
evaluation kits.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The EDT ETM0700G0DH6 and ET070080DH6 are 7" 800x480 panels,
which can be supported by the simple panel driver.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This panel is used by Tegra Note 7 and supported by the simple-panel
driver.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This panel is used by the NVIDIA SHIELD and supported by the
simple-panel driver.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to differentiate between the different video modes (burst vs.
non-burst, sync pulses vs. sync events) supported by peripherals, pass
the flags that specify this mode in the panel description to the DSI
peripheral device when probed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The enable GPIO for panels may be provided by GPIO expanders on slow
busses (such as I2C), and therefore toggling the GPIO may sleep. Since
these accesses don't happen in interrupt context, use the *_cansleep()
variants of the GPIO API.
Signed-off-by: Thierry Reding <treding@nvidia.com>
regulator_disable() is already performed by panel_simple_disable(),
which is called by panel_simple_remove().
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use the new GPIO descriptor interface to handle the panel's enable GPIO.
This considerably simplifies the code.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
[treding@nvidia.com: rework to improve readability]
Signed-off-by: Thierry Reding <treding@nvidia.com>
This stashes away the EDID data so that the sysfs per-connector file
"edid" can display it. Without this change, the "edid" file is always
empty.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Chunghwa CLAA101WA01A is a 10.1" 1366x768 panel, which can be
supported by the simple panel driver.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Samsung LNT101NT05 10.1" WXVGA panel can be supported by the simple panel
driver.
Cc: linux-fbdev@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Lucas Stach