Panic() invokes printk() to add a \n internally, so panic arguments should
not themselves end in \n. Panic invocations in arch/mips and elsewhere
are inconsistently sometimes terminating in \n, sometimes not.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Or else we get lots of variations on this:
arch/mips/pci/pci.c:330: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL'
scattered throughout the build.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This patch add support for the bcma bus. Broadcom uses only Mips 74K
CPUs on the new SoC and on the old ons using ssb bus there are no Mips
74K CPUs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prepare bcm47xx to support different System buses. Before adding
support for bcma it should be possible to build bcm47xx without the
need of ssb. With this patch bcm47xx does not directly contain a
ssb_bus, but a union contain all the supported system buses. As a SoC
just uses one system bus a union is a good choice.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some members of the struct ssb_sprom where not filled with data available
in the NVRAM. Some attribute names in the NVRAM changed from SPROM version
3 to version 4. This patch was done by analyzing the the pci sprom parser
in the ssb code and some open source parts of the braodcom wireless driver
used on embedded devices.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2365/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We are generating the prefix based on the PCI bus address the device is
on. This is done like Broadcom does it in their code expect that the the
bus number is increased by one. In the SB bus implementation used by
Broadcom the SB bus emulates a PCI bus so the kernel sees one PCI bus
more then in our implementation. We do not handle prefixes like sb/1/
yet as they are only used on the new bus which is not implemented yet.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2364/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When an other SSB based device without an own SPROM is attached, using the
PCI bus to the main SSB based device, the data normally found in the SPROM
will be stored in the NVRAM on modern devices. The keys, to load the data
from the NVRAM, are all using some sort of prefix like pci/1/1/, pci/1/3/
or sb/1/ before the actual key. This patch extends bcm47xx_fill_sprom() to
make it possible to read out these values when some prefix was used.
The keys for the SPROM data used on the main chip does not have a prefix.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2363/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some devices like the Netgear WGT634U are using ttyS1 for default console
output. We should switch to that console if it was given in the kernel_args
parameters.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/1848/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Instead of writing own function for parsing the mac address we now
use sscanf.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/1847/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fill the sprom with all available values from the nvram. Most of these
new values are needed for the b43 or b43legacy driver.
Parts of this patch have been in OpenWRT for a long time and were written
by Michael Buesch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/1846/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The config options read out here are not stored in CFE but only in NVRAM on
the devices. Remove reading from CFE and only access the NVRAM. Reading out
CFE does not harm but is useless here.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/1845/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When trying to netboot a Linksys WRT54GS WLAN router, the bootup fails,
because of following error message:
...
[ 0.424000] b44: b44.c:v2.0
[ 0.424000] b44: Invalid MAC address found in EEPROM
[ 0.432000] b44 ssb0:1: Problem fetching invariants of chip,aborting
[ 0.436000] b44: probe of ssb0:1 failed with error -22
...
The router uses a CFE bootloader, but most of the needed environment
variables for network card initialization, are not available from CFE
via printenv and even though not via cfe_getenv().
The required environment variables are saved in a special partition
in flash memory. The attached patch implement nvram_getenv and enables
bootup via NFS root on my router.
Most of the patch is extracted from the OpenWrt subversion repository and
stripped down and cleaned up to just fix this issue.
[Ralf: sorted out header file inclusions. Lots of unneded headers and such
that should have been included.]
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
Reviewed-by: Phil Sutter <phil@nwl.cc>
To: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/1359/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch simplifies the BCM47xx GPIO code by using the new SSB GPIO
API, which does a lot things that were implemented directly in the
BCM47xx code.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Switch the BCM47XX code to the new SPROM data structure now that the old
one has been removed.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Hard to follow who is pointing what to where and why so it's simply getting
in the way of the time code renovation.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add CFE support to the BCM47XX code. That includes querying CFE environment
variables as well as using CFE to print messages before the serial port is
initialized (early printk).
Signed-off-by: Aurelien Jarno <aurel32@farad.aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Note that the BCM4710 does not support the wait instruction, this
is not a mistake in the code.
It originally comes from the OpenWrt patches.
Cc: Michael Buesch <mb@bu3sch.de>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: Florian Schirmer <jolt@tuxbox.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle