The PRUSSs on AM57xx SoCs contain an MDIO controller that can
be used to control external PHYs associated with the Industrial
Ethernet peripherals within each PRUSS. The MDIO module used
within the PRU-ICSS is an instance of the MDIO Controller used
in TI Davinci SoCs. The same bus frequency of 1 MHz is chosen as
the regular MDIO node.
The nodes are added in the common am57-pruss.dtsi file and enabled
by default, but are disabled in all the existing AM57xx board dts
files. These nodes need pinctrl lines, and so should be enabled
only on boards where they are actually wired and pinned out for
PRUSS Ethernet. Any new board dts file should disable these if
they are not sure.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Switch all am571/2/4-idk boards to use new cpsw switch driver.
Those boards have 2 Ext. port wired and configured in dual_mac mode by
default. Hence, dual_mac mode has been preserved the same way between
legacy and new driver it's safe to switch drivers.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is the set of device tree changes, mostly covering new
hardware support, with 577 patches touching a little over 500
files.
There are five new Arm SoCs supported in this release, all of
them for existing SoC families:
- Realtek RTD1195, RTD1395 and RTD1619 -- three SoCs used in
both NAS devices and Android Set-top-box designs, along
with the "Horseradish", "Lion Skin" and "Mjolnir" reference
platforms; the Mele X1000 and Xnano X5 set-top-boxes and
the Banana Pi BPi-M4 single-board computer.
- Renesas RZ/G1H (r8a7742) -- a high-end 32-bit industrial SoC
and the iW-RainboW-G21D-Qseven-RZG1H board/SoM
- Rockchips RK3326 -- low-end 64-bit SoC along with the
Odroid-GO Advance game console
Newly added machines on already supported SoCs are:
- AMLogic S905D based Smartlabs SML-5442TW TV box
- AMLogic S905X3 based ODROID-C4 SBC
- AMLogic S922XH based Beelink GT-King Pro TV box
- Allwinner A20 based Olimex A20-OLinuXino-LIME-eMMC SBC
- Aspeed ast2500 based BMCs in Facebook x86 "Yosemite V2"
and YADRO OpenPower P9 "Nicole"
- Marvell Kirkwood based Check Point L-50 router
- Mediatek MT8173 based Elm/Hana Chromebook laptops
- Microchip SAMA5D2 "Industrial Connectivity Platform"
reference board
- NXP i.MX8m based Beacon i.MX8m-Mini SoM development kit
- Octavo OSDMP15x based Linux Automation MC-1 development board
- Qualcomm SDM630 based Xiaomi Redmi Note 7 phone
- Realtek RTD1295 based Xnano X5 TV Box
- STMicroelectronics STM32MP1 based Stinger96 single-board
computer and IoT Box
- Samsung Exynos4210 based based Samsung Galaxy S2 phone
- Socionext Uniphier based Akebi96 SBC
- TI Keystone based K2G Evaluation board
- TI am5729 based Beaglebone-AI development board
Include device descriptions for additional hardware support in existing
SoCs and machines based on all major SoC platforms:
- AMlogic Meson
- Allwinner sunxi
- Arm Juno/VFP/Vexpress/Integrator
- Broadcom bcm283x/bcm2711
- Hisilicon hi6220
- Marvell EBU
- Mediatek MT27xx, MT76xx, MT81xx and MT67xx
- Microchip SAMA5D2
- NXP i.MX6/i.MX7/i.MX8 and Layerscape
- Nvidia Tegra
- Qualcomm Snapdragon
- Renesas r8a77961, r8a7791
- Rockchips RK32xx/RK33xx
- ST-Ericsson ux500
- STMicroelectronics SMT32
- Samsung Exynos and S5PV210
- Socionext Uniphier
- TI OMAP5/DRA7 and Keystone
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=17kt
-----END PGP SIGNATURE-----
Merge tag 'arm-dt-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM devicetree updates from Arnd Bergmann:
"This is the set of device tree changes, mostly covering new hardware
support, with 577 patches touching a little over 500 files.
There are five new Arm SoCs supported in this release, all of them for
existing SoC families:
- Realtek RTD1195, RTD1395 and RTD1619 -- three SoCs used in both NAS
devices and Android Set-top-box designs, along with the
"Horseradish", "Lion Skin" and "Mjolnir" reference platforms; the
Mele X1000 and Xnano X5 set-top-boxes and the Banana Pi BPi-M4
single-board computer.
- Renesas RZ/G1H (r8a7742) -- a high-end 32-bit industrial SoC and
the iW-RainboW-G21D-Qseven-RZG1H board/SoM
- Rockchips RK3326 -- low-end 64-bit SoC along with the Odroid-GO
Advance game console
Newly added machines on already supported SoCs are:
- AMLogic S905D based Smartlabs SML-5442TW TV box
- AMLogic S905X3 based ODROID-C4 SBC
- AMLogic S922XH based Beelink GT-King Pro TV box
- Allwinner A20 based Olimex A20-OLinuXino-LIME-eMMC SBC
- Aspeed ast2500 based BMCs in Facebook x86 "Yosemite V2" and YADRO
OpenPower P9 "Nicole"
- Marvell Kirkwood based Check Point L-50 router
- Mediatek MT8173 based Elm/Hana Chromebook laptops
- Microchip SAMA5D2 "Industrial Connectivity Platform" reference
board
- NXP i.MX8m based Beacon i.MX8m-Mini SoM development kit
- Octavo OSDMP15x based Linux Automation MC-1 development board
- Qualcomm SDM630 based Xiaomi Redmi Note 7 phone
- Realtek RTD1295 based Xnano X5 TV Box
- STMicroelectronics STM32MP1 based Stinger96 single-board computer
and IoT Box
- Samsung Exynos4210 based based Samsung Galaxy S2 phone
- Socionext Uniphier based Akebi96 SBC
- TI Keystone based K2G Evaluation board
- TI am5729 based Beaglebone-AI development board
Include device descriptions for additional hardware support in
existing SoCs and machines based on all major SoC platforms:
- AMlogic Meson
- Allwinner sunxi
- Arm Juno/VFP/Vexpress/Integrator
- Broadcom bcm283x/bcm2711
- Hisilicon hi6220
- Marvell EBU
- Mediatek MT27xx, MT76xx, MT81xx and MT67xx
- Microchip SAMA5D2
- NXP i.MX6/i.MX7/i.MX8 and Layerscape
- Nvidia Tegra
- Qualcomm Snapdragon
- Renesas r8a77961, r8a7791
- Rockchips RK32xx/RK33xx
- ST-Ericsson ux500
- STMicroelectronics SMT32
- Samsung Exynos and S5PV210
- Socionext Uniphier
- TI OMAP5/DRA7 and Keystone"
* tag 'arm-dt-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (564 commits)
ARM: dts: keystone: Rename "msmram" node to "sram"
arm: dts: mt2712: add uart APDMA to device tree
arm64: dts: mt8183: add mmc node
arm64: dts: mt2712: add ethernet device node
arm64: tegra: Make the RTC a wakeup source on Jetson Nano and TX1
ARM: dts: mmp3: Add the fifth SD HCI
ARM: dts: berlin*: Fix up the SDHCI node names
ARM: dts: mmp3: Fix USB & USB PHY node names
ARM: dts: mmp3: Fix L2 cache controller node name
ARM: dts: mmp*: Fix up encoding of the /rtc interrupts property
ARM: dts: pxa*: Fix up encoding of the /rtc interrupts property
ARM: dts: pxa910: Fix the gpio interrupt cell number
ARM: dts: pxa3xx: Fix up encoding of the /gpio interrupts property
ARM: dts: pxa168: Fix the gpio interrupt cell number
ARM: dts: pxa168: Add missing address/size cells to i2c nodes
ARM: dts: dove: Fix interrupt controller node name
ARM: dts: kirkwood: Fix interrupt controller node name
arm64: dts: Add SC9863A emmc and sd card nodes
arm64: dts: Add SC9863A clock nodes
arm64: dts: mt6358: add PMIC MT6358 related nodes
...
Since commit bcf3440c6d ("net: phy: micrel: add phy-mode support for the
KSZ9031 PHY") the networking is broken on boards:
am571x-idk
am572x-idk
am574x-idk
am57xx-beagle-x15
All above boards have phy-mode = "rgmii" and this is worked before because
KSZ9031 PHY started with default RGMII internal delays configuration (TX
off, RX on 1.2 ns) and MAC provided TX delay. After above commit, the
KSZ9031 PHY starts handling phy mode properly and disables RX delay, as
result networking is become broken.
Fix it by switching to phy-mode = "rgmii-rxid" to reflect previous
behavior.
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Fixes: bcf3440c6d ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY")
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CMA reserved memory nodes have been added for both the IPUs and the
DSP1 remoteproc devices on the AM571x IDK board. These nodes are assigned
to the respective rproc device nodes, and both the IPUs and the DSP1
remote processors are enabled for this board.
The current CMA pools and sizes are defined statically for each device.
The addresses chosen are the same as the respective processors on the
DRA72 EVM board to maintain firmware compatibility between the two boards.
The CMA pools and sizes are defined using 64-bit values to support LPAE.
The starting addresses are fixed to meet current dependencies on the
remote processor firmwares, and this will go away when the remote-side
code has been improved to gather this information runtime during its
initialization.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The System Mailboxes 5 and 6 and their corresponding child sub-mailbox
(IPC 3.x) nodes are enabled in each of the DRA7xx and AM57xx board
dts files individually at present. These mailboxes enable the Remote
Processor Messaging (RPMsg) communication stack between the MPU host
processor and each of the IPU1, IPU2, DSP1 and DSP2 remote processors.
Move these nodes into two common dtsi files - dra7-ipu-dsp-common and
dra74-ipu-dsp-common files, which are then included in various board
dts files. These files can be used to add all the common configuration
properties (except memory data) required by remote processor nodes.
The memory pools and the remote processor nodes themselves are to be
enabled in the actual board dts files. The first file is to used by
platforms using DRA72x/DRA71x/AM571x/AM570x SoCs, and the second file
is to be used by platforms using DRA74x/DRA76x/AM572x/AM574x SoCs.
The second file includes the first file and contains additional data
only applicable for DSP2 remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
commit d23f3839fe ("ARM: dts: DRA7: Add pcie1 dt node for
EP mode") while adding the dt node for EP mode for DRA7 platform,
added rc node for am571x-idk and populated gpios property with
"gpio3 23". However the GPIO_PCIE_SWRST line is actually connected
to "gpio5 18". Fix it here. (The patch adding "gpio3 23" was tested
with another am57x board in EP mode which doesn't rely on reset from
host).
Cc: stable <stable@vger.kernel.org> # 4.14+
Fixes: d23f3839fe ("ARM: dts: DRA7: Add pcie1 dt node for EP mode")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
PERST# line in the PCIE connector is driven by the host mode and not
EP mode. The gpios property here is used for driving the PERST# line.
Remove gpios property from all endpoint device tree nodes.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add DT nodes for new cpsw switchdev driver for am571x-idk board for now to
enable testing of the new solution.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If UHS speed modes are enabled, a compatible SD card switches down to
1.8V during enumeration. If after this a software reboot/crash takes
place and on-chip ROM tries to enumerate the SD card, the difference in
IO voltages (host @ 3.3V and card @ 1.8V) may end up damaging the card.
The fix for this is to have support for power cycling the card in
hardware (with a PORz/soft-reset line causing a power cycle of the
card). Because the beaglebone X15 (rev A,B and C), am57xx-idks and
am57xx-evms don't have this capability, disable voltage switching for
these boards.
The major effect of this is that the maximum supported speed
mode is now high speed(50 MHz) down from SDR104(200 MHz).
commit 88a748419b ("ARM: dts: am57xx-idk: Remove support for voltage
switching for SD card") did this only for idk boards. Do it for all
affected boards.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AM5 and DRA7 SoC families have different set of modules
in them so the SoC sepecific dtsi files need to be separated.
e.g. Some of the major differences between AM576 and DRA76
DRA76x AM576x
USB3 x
USB4 x
ATL x
VCP x
MLB x
ISS x
PRU-ICSS1 x
PRU-ICSS2 x
This patch only deals with disabling USB3, USB4 and ATL for
AM57 variants.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
am574x-idk has no cpu vdd-supply at the moment. Hence hook smps12
regulator as cpu vdd-supply in am57xx-idk-common as the same regulator
feeds on to cpu on am571/2/4-idks. So remove all the individual
instances and place that in common place.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The SN65HVS882 load trigger is attached to GPIO2_23 on the AM571x IDK.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM571x-IDK rev 1.2A has tricolor RGB LEDs that can be controlled using
GPIO. Expose these to userspace for usage as necessary.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Dual-role support was added in v4.12. We should be using
it for USB2 port on the am57xx-idk.
Cc: <stable@vger.kernel.org> [4.16+]
Reported-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IO lines of MMC2 in am57xx-beagle-x15/am57xx-idk is connected to
3.3v. Use "ddr_3_3v" instead of "ddr_1_8v" to indicate DDR mode
works in 3.3v on these boards.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
commit 18aa0f4bca ("ARM: dts: am57xx-idk: Select pull down
for mmc1_clk line in default mode") modified mmc1_pins_default
pinctrl group in am57xx-idk-common.dtsi in order to change the CLK
line to PIN_INPUT_PULLDOWN. However instead of modifying the pinctrl
group, use the new pinctrl group "mmc1_pins_default_no_clk_pu" in
dra7-mmc-iodelay.dtsi added specifically to be used for CLK line without
external pull up.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
During a short period when the bus voltage is switched from 3.3v to 1.8v,
(to enumerate UHS mode), the mmc module is disabled and the mmc IO lines
are kept in a state according to the programmed pad mux pull type.
According to 4.2.4.2 Timing to Switch Signal Voltage in "SD Specifications
Part 1 Physical Layer Specification Version 5.00 February 22, 2016", the
host should hold CLK low for at least 5ms.
In order to keep the card line low during voltage switch, the pad mux of
mmc1_clk line should be configured to pull down.
This is specific to am57xx-idk (and not all dra72/dra74 based boards)
since mmc1_clk line in am57xx-idk is not connected to an external
pullup.
While at that change the order of header files in am571x-idk.dts and
am572x-idk.dts so that the modified pinctrl values in am57xx-idk-common
could take effect.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Include dra72x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra72 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in am571x-idk.dts.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM572x IDK and AM571x IDK boards have equivalent
design of how SD card and eMMC are connected.
The two EVMs mainly differ in IOdelay configuration
needed (because of difference in SoC used).
Move the common properties to am57xx-idk-common.dtsi
file which is common for both EVMs.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pcie1 dt node in order for the controller to operate in
endpoint mode. However since none of the dra7 based boards have
slots configured to operate in endpoint mode, keep EP mode
disabled.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The GPIO polarity for MMC1 card detect is set to '0' which means
active-high. However the polarity should be active-low. Fix it
here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable the System Mailboxes 5 and 6 and the corresponding
child sub-mailbox (IPC 3.x) nodes for the AM571x IDK board.
This is needed to enable communication with the respective
remote processors IPU1, IPU2, and DSP1 from the MPU.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
VBUS detection is available on the board via the palmas PMIC.
Use extcon-palmas driver instead of extcon-gpio-usb driver.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The AM571x-IDK board is a board based on TI's AM5718 SOC
which has a single core 1.5GHz A15 processor. This board is a
development platform for the Industrial market with:
- 1GB of DDR3L
- Dual 1Gbps Ethernet
- HDMI,
- PRU-ICSS
- uSD
- 16GB eMMC
- CAN
- RS-485
- PCIe
- USB3.0
- Video Input Port
- Industrial IO port and expansion connector
The link to the data sheet and TRM can be found here:
http://www.ti.com/product/AM5718
Initial support is only for basic peripherals.
Signed-off-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Suman Anna