dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191217112737.31024-1-peter.ujfalusi@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For the ux500v2 variant of the PL18x block, any block sizes
are supported. This is necessary to support some SDIO
transfers. This also affects the QCOM MMCI variant and the
ST micro variant.
For Ux500 an additional quirk only allowing DMA on blocks
that are a power of two is needed. This might be a bug in
the DMA engine (DMA40) or the MMCI or in the interconnect,
but the most likely is the MMCI, as transfers of these
sizes work fine for other devices using the same DMA
engine. DMA works fine also with SDIO as long as the
blocksize is a power of 2.
This patch has proven necessary for enabling SDIO for WLAN on
PostmarketOS-based Ux500 platforms.
What we managed to test in practice is Broadcom WiFi over
SDIO on the Ux500 based Samsung GT-I8190 and GT-S7710.
This WiFi chip, BCM4334 works fine after the patch.
Before this patch:
brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4334-sdio
for chip BCM4334/3
mmci-pl18x 80118000.sdi1_per2: unsupported block size (60 bytes)
brcmfmac: brcmf_sdiod_ramrw: membytes transfer failed
brcmfmac: brcmf_sdio_download_code_file: error -22 on writing
434236 membytes at 0x00000000
brcmfmac: brcmf_sdio_download_firmware: dongle image file download
failed
After this patch:
brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4334/3 wl0:
Nov 21 2012 00:21:28 version 6.10.58.813 (B2) FWID 01-0
Bringing up networks, discovering networks with "iw dev wlan0 scan"
and connecting works fine from this point.
This patch is inspired by Ulf Hansson's patch
http://www.spinics.net/lists/linux-mmc/msg12160.html
As the DMA engines on these platforms may now get block sizes
they were not used to before, make sure to also respect if
the DMA engine says "no" to a transfer.
Make a drive-by fix for datactrl_blocksz, misspelled.
Cc: Ludovic Barre <ludovic.barre@st.com>
Cc: Brian Masney <masneyb@onstation.org>
Cc: Stephan Gerhold <stephan@gerhold.net>
Cc: Niklas Cassel <niklas.cassel@linaro.org>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20191217143952.2885-1-linus.walleij@linaro.org
The stm32_sdmmc variant has build-in support for datatimeout for R1B
requests. If a corresponding IRQ is raised, this triggers the DPSM to stay
busy and remains in a non-functional state. Only a reset can bring it back
to a functional state.
Because a reset must be issued from non-atomic context, let's defer this to
be managed from a threaded IRQ handler. Besides the reset, the threaded
handler also calls mmc_request_done(), to finally complete the request.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20191211133934.16932-1-ludovic.Barre@st.com
[Ulf: A few minor updates to the changelog/comments]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let's drop the boilerplate code for managing the default pinctrl state and
convert into using the new pinctrl_select_default_state().
Additionally, move away from using pinctrl_pm_select_default_state() as
it's scheduled for removal and use pinctrl_select_default_state() instead.
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191206170821.29711-4-ulf.hansson@linaro.org
This patch adds a specific busy_complete callback for sdmmc variant.
sdmmc has 2 status flags:
-busyd0: This is a hardware status flag (inverted value of d0 line).
it does not generate an interrupt.
-busyd0end: This indicates only end of busy following a CMD response.
On busy to Not busy changes, an interrupt is generated (if unmask)
and BUSYD0END status flag is set. Status flag is cleared by writing
corresponding interrupt clear bit in MMCICLEAR.
The legacy busy completion has no dedicated interrupt for the end
of busy, so it's must monitor step by step the busy progression.
On sdmmc variant, this procedure is not needed, it's just need
to wait the busyd0end interrupt.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds busy_completion callback at mmci_host_ops
to allow to define a specific busy completion by variant.
The legacy code corresponding to busy completion used
by ux500 variants is moved to ux500_busy_complete function.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the stm32_sdmmc variant, the datatimer is active not only during
data transfers with the DPSM, but also while waiting for the busyend
IRQs from commands having the MMC_RSP_BUSY flag set. This leads to an
incorrect IRQ being raised to signal MCI_DATATIMEOUT error, which
simply breaks the behaviour.
Address this by updating the datatimer value before sending a command
having the MMC_RSP_BUSY flag set. To inform the mmc core about the
maximum supported busy timeout, which also depends on the current
clock rate, set ->max_busy_timeout (in ms).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix the following sparse warnings by making any functions not used
outsde the mmci.c driver static.
drivers/mmc/host/mmci.c:422:6: warning: symbol 'mmci_dma_release' was not declared. Should it be static?
drivers/mmc/host/mmci.c:430:6: warning: symbol 'mmci_dma_setup' was not declared. Should it be static?
drivers/mmc/host/mmci.c:465:5: warning: symbol 'mmci_prep_data' was not declared. Should it be static?
drivers/mmc/host/mmci.c:481:6: warning: symbol 'mmci_unprep_data' was not declared. Should it be static?
drivers/mmc/host/mmci.c:490:6: warning: symbol 'mmci_get_next_data' was not declared. Should it be static?
drivers/mmc/host/mmci.c:498:5: warning: symbol 'mmci_dma_start' was not declared. Should it be static?
drivers/mmc/host/mmci.c:533:6: warning: symbol 'mmci_dma_finalize' was not declared. Should it be static?
drivers/mmc/host/mmci.c:542:6: warning: symbol 'mmci_dma_error' was not declared. Should it be static?
drivers/mmc/host/mmci.c:951:6: warning: symbol 'mmci_variant_init' was not declared. Should it be static?
drivers/mmc/host/mmci.c:956:6: warning: symbol 'ux500v2_variant_init' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The code dealing with busy detection is somewhat complicated. In a way to
make it a bit clearer, let's try to clarify the comments in the code about
it.
Additionally, move the part for clearing the so called busy start IRQ, to
the place where the IRQ is actually delivered. Ideally, this should make
the code a bit more robust.
Finally, to improve understanding of the code and the sequence of the busy
detection, move the corresponding code around a bit in mmci_cmd_irq().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Jean Nicolas GRAUX <jean-nicolas.graux@st.com>
Reviewed-by: Jean Nicolas GRAUX <jean-nicolas.graux@st.com>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IRQ handler, mmci_irq(), loops until all status bits have been cleared.
However, the status bit signaling busy in variant->busy_detect_flag, may be
set even if busy detection isn't monitored for the current request.
This may be the case for the CMD11 when switching the I/O voltage, which
leads to that mmci_irq() busy loops in IRQ context. Fix this problem, by
clearing the status bit for busy, before continuing to validate the
condition for the loop. This is safe, because the busy status detection has
already been taken care of by mmci_cmd_irq().
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let's cleanup the mmci_cmd_irq() a bit, to make the busy detect code more
clear.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch allows to get datactrl configuration specific
at variant. This introduce more flexibility on datactlr
value.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As mmci_variant_init() is a local function to mmci.c, let's convert it into
static.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
It's good practice to share functions via header files, rather than from
the c-files. Therefore, let's move sdmmc_variant_init() to mmci.h.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Ludovic Barre <ludovic.barre@st.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
It seems a bit silly to have a header file to share only the
qcom_variant_init() function. So, let's just drop it and move the
declaration of the function into the common mmci.h instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Having mmci_dmae_start() to invoke the shared function, dml_start_xfer(),
explicitly for the qcom variant isn't very nice. Let's clean up this code
by moving the qcom specific parts into the qcom ->dma_start() callback and
then drop dml_start_xfer() altogether.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The current approach with sending a CMD12 (STOP_TRANSMISSION) to complete a
data transfer request, either because of using the open-ended transmission
type or because of receiving an error during a pre-defined data transfer,
isn't sufficient for the STM32 sdmmc variant. More precisely, this variant
needs to clear the DPSM ("Data Path State Machine") by sending a CMD12, for
all failing ADTC commands.
Support this, by adding a struct mmc_command inside the struct mmci_host
and initialize it to a CMD12 during ->probe(). Let's also add checks for
the new conditions, to enable mmci_data_irq() and mmci_cmd_irq() to
postpone the calls to mmci_request_end(), but instead send the CMD12.
Cc: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
The argument "override_active_level" made it possible to
enforce a specific polarity on the write-protect
GPIO line. All callers in the kernel pass "false" to this
call after I have converted all drivers to use GPIO machine
descriptors, so remove the argument and clean out this.
This kind of polarity inversion should be handled by the
GPIO descriptor inside the GPIO library if needed.
This rids us of one instance of the kludgy calls into
the gpiod_get_raw_value() API.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On cmd12 (STOP_TRANSMISSION), STM32 sdmmc variant needs to set
cmdstop bit in command register. The CPSM ("Command Path State Machine")
treats the command as a Stop Transmission command and signals
abort to the DPSM ("Data Path State Machine").
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Refer to "4.15 set block count command" of sd specification:
Host needs to issue CMD12 if any error is detected in
the CMD18 and CMD25 operations.
In sbc case, the data->stop is fill by framework.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Tested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a stm32 sdmmc variant, rev 1.1.
Introduces a new Manufacturer id "0x53, ascii 'S' to define
new stm32 sdmmc family with clean range of amba
revision/configurations bits (corresponding to sdmmc_ver
register with major/minor fields).
Add 2 variants properties:
-dma_lli, to enable link list support.
-stm32_idmabsize_mask, defines the range of SDMMC_IDMABSIZER register
which specify the number bytes per buffer.
DT properties for sdmmc:
-Indicate signal directions (only one property
for d0dir, d123dir, cmd_dir)
-Select command and data phase relation.
-Select "clock in" from an external driver.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The STM32 sdmmc variant has a different clock divider.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a optional reset management.
STM32 sdmmc variant needs to reset hardware block
during the power cycle procedure (for re-initialization).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a boolean property to not read datacnt register.
Needed to support the STM32 sdmmc variant. MMCIDATACNT
register should be read only after the data transfer is completed.
When reading after an error event the read data count value may be
different from the real number of data bytes transferred.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a boolean property to allow to write datactrl
before to send command, whatever the command type (read or write).
Needed to support the STM32 sdmmc variant.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch allows to define specific pio mask for variants.
Needed to support the STM32 sdmmc variant which has some bits
with different meaning (bits: 21,20,13,12,9)
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds datactrl variant property to define
dpsm enable bit. Needed to support the STM32 variant
(STM32 has no dpsm enable bit).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds command variant properties to define
cpsm enable bit and responses.
Needed to support the STM32 variant (shift of cpsm bit,
specific definition of commands response).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All variants don't pretend to have a startbiterr.
-While data error check, if status register return an error
(like MCI_DATACRCFAIL) we must avoid to check MCI_STARTBITERR
(if not desired).
-expand start_err to MCI_IRQENABLE to avoid to set this bit by default.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch allows to define a datactrl block size
by variant, requested by STM32 sdmmc variant.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds set_clkreg and set_pwrreg callbacks
at mmci_host_ops to allow to call specific variant.
extends visibility of mmci_write_clk/pwrreg functions
to be used into specific file variant.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds validate_data callback at mmci_host_ops
to check specific constraints of variant.
Move mmci_validate_data function to regroup mmci_host_ops interfaces.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds dma_error callback at mmci_host_ops
to allow to call specific variant.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds dma_finalize callback at mmci_host_ops
to allow to call specific variant.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds dma_start callback to mmci_host_ops.
Create a generic mmci_dma_start function which regroup
common action between variant.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds prepare/unprepare callbacks to mmci_host_ops.
Like this mmci_pre/post_request can be generic, mmci_prepare_data
and mmci_unprepare_data provide common next_cookie management.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch merges the prepare data functions.
This allows to define a single access to prepare data service.
This prepares integration for mmci host ops.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-Introduces dma_priv pointer to define specific
needs for each dma engine. This patch is needed to prepare
sdmmc variant with internal dma which not use dmaengine API.
-Moves next cookie to mmci host structure to share same cookie
management between all variants.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch creates a common mmci_dma_setup/release which calls
dma_setup/release callbacks of mmci_host_ops and manages
common features like use_dma... If there is a fallbacks to
pio mode, dma functions must check use_dma.
error management:
-mmci_dmae_setup fail if Tx and Rx dma channels are not defined
-qcom_dma_setup fail if one of both dma channels is not defined,
Qcom has no specific resource to release, just mmci dmae resource.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch internalizes the dma_inprogress into mmci dma interfaces.
This allows to simplify and prepare the next dma callbacks
for mmci host ops. dma_inprogress is called in mmci_dma_data_error
and mmci_dma_finalize.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch internalizes the management of dma map/unmap into
mmci dma interfaces. This allows to simplify and prepare the next dma
callbacks for mmci host ops.
mmci_dma_unmap was called in mmci_data_irq & mmci_cmd_irq functions
and can be integrated in mmci_dma_data_error.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All the machines using the MMCI are passing GPIOs for the
card detect and write protect using the device tree or
descriptor table (one single case, Integrator/AP IM-PD1).
Drop support for passing global GPIO numbers through
platform data, noone is using it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As a first step to improve the variant specific code for mmci, add a
->dma_setup() callback to the struct mmci_host_ops.
To show its use, let's deploy the callback for the qcom dml, which involves
also to the assign the mmci_host_ops pointer from the variant ->init()
callback.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
To be able to better support different mmci variants, we need to be able to
use variant specific callbacks, rather than continue to sprinkle the code
with additional variant data. To move in this direction, let's add an
optional ->init() callback to the variant data struct, which variants shall
use to assign the mmci_host_ops pointer.
Using an ->init() callback enables us to partition the code between
different files. To allow separate mmci variant files to implement the
variant specifics, let's also move the definition of the struct
variant_data to the common mmci header file.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
On !RT interrupt runs with interrupts disabled. On RT it's in a
thread, so no need to disable interrupts at all.
Remove the local_irq_save() invocation.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: f9bb304ce8 ("mmc: mmci: Add support for setting pad type via pinctrl")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Peter Ujfalusi