witherspoon hardware and p9 chips have very sensitive requirements for
the cfam-reset. We're seeing power faults with the kernel based cfam
reset due to this.
Could adapt the power application to use the new kernel based cfam reset
interface but there's not a lot to be gained there since the power
application is going away with p10 and this limitation is not present in
p10.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20210308225419.46530-17-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
The GPIO is used to place the BMC-connected TPM in reset.
The net is called BMC_TPM_RST_N on Tacoma.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20210727033319.473152-3-joel@jms.id.au
The degree values were reversed out from the magic tap values of 7 (in)
and 15 + inversion (out) initially suggested by Aspeed.
With the patch tacoma survives several gigabytes of reads and writes
using dd while without it locks up randomly during the boot process.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20210625061017.1149942-1-andrew@aj.id.au
Fixes: 2fc88f9235 ("mmc: sdhci-of-aspeed: Expose clock phase controls")
Fixes: 961216c135 ("ARM: dts: aspeed: Add Rainier system")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Tacoma and Rainier both have a line-names array that is too long:
gpio gpiochip0: gpio-line-names is length 232 but should be at most length 208
This was probably copied from an AST2500 device tree that did have more
GPIOs on the controller.
Fixes: e9b24b55ca ("ARM: dts: aspeed: rainier: Add gpio line names")
Fixes: 2f68e4e7df ("ARM: dts: aspeed: tacoma: Add gpio line names")
Link: https://lore.kernel.org/r/20210624090742.56640-1-joel@jms.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
Most of the aspeed boards have copied the 'earlyprink' string in
the bootargs. However, there's no earlyprink driver configured in the
defconfigs, so this does nothing.
A combination of setting stdout in the chosen node and adding earlycon
to bootargs causes early serial output to appear early. This changes all
boards to use this option.
The console=ttyS4,115200 option is still required, as this is used by
the run time uart driver.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Alexander Filippov <a.filippov@yadro.com>
Link: https://lore.kernel.org/r/20210526051220.136432-1-joel@jms.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reserve a 1.5MiB region of memory to record kmsg dumps, console and
userspace message state into 16kiB ring-buffer slots. The sizing allows
for up to 16 dumps to be captured and read out.
Set max-reason to KMSG_DUMP_EMERG to capture bad-path reboots.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20201022014731.2035438-7-andrew@aj.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
The mismatch lead to a miscalculation of regions in another patch, and
shouldn't be mismatched anyway, so make them consistent.
Fixes: 575640201e ("ARM: dts: aspeed: tacoma: Use 64MB for firmware memory")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20201022014731.2035438-2-andrew@aj.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
Set I2C bus 0 to multi-master mode and add the panel device that will
register as a slave.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20200908200101.64974-5-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Enable the second EHCI controller on the AST2600. Also add a line-name
for the GPIO that controls power to the USB port.
The power control is in place to allow the port to be disabled, for
those that are worried about rogue USB sticks.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The GPIO on Q0 is used for resetting the CFAM of the processor that the
ASPEED master is connected to.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The attention handler will monitor the checkstop gpio via the character
device interface so it needs to not be defined.
Signed-off-by: Ben Tyner <ben.tyner@ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add a reserved memory node for the VGA memory. Add the XDMA engine node,
enable it, and point it's memory region to the VGA memory.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Connect the BMP280 and DPS310 to the hwmon subsystem with iio-hwmon
nodes.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
GPIO Q7 is no longer used for air/water. It is repurposed on Tacoma to
indicate internal FSI (low) vs cabled (high).
GPIO B0 controls the muxing of FSI to the cable (low) or internal pins
(high).
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add gpio-keys for various signals on Tacoma.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Enabling emmc without enabling its controller doesn't do any good.
Enable its controller as well to make it work.
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Joel Stanley <joel@jms.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This is a revert of "ARM: dts: aspeed: tacoma: Enable FMC and SPI
devices" which was already applied as part of "ARM: dts: aspeed: Add
Tacoma machine".
Fixes: 8737481e38 ("ARM: dts: aspeed: tacoma: Enable FMC and SPI devices")
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This is a revert of "ARM: dts: aspeed: tacoma: Enable I2C busses", which
was already applied as part of "ARM: dts: aspeed: Add Tacoma machine".
Fixes: 606bcdde67 ("ARM: dts: aspeed: tacoma: Enable I2C busses")
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Requesting pinmux configuration is done at driver probe time. The LPC IP
is composed of many sub-devices, each with their own driver, and no
driver exists for the entire IP block. Avoid having each sub-device
request the LPC pinmux by just hogging it in the pinctrl node.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
OpenBMC requires a window the same size as the image being loaded.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The UARTs on the AST2600 A0 have a known issue that can be worked around
by using the Synopsys driver.
Tested-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
We need to ungate RCLK on AST2500- and AST2600-based platforms for RMII
to function. RMII interfaces are commonly used for NCSI.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add gpio-keys for various signals on Tacoma.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Enable all the I2C busses on Tacoma and add the I2C slave devices that
exist on the busses.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Eddie James