Add support to create thermal zones based on the temperature sensors
provided by the SCP. The thermal zones can be defined using the
thermal DT bindings and should refer to the SCP sensor id to select
the sensor.
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Cc: Eduardo Valentin <edubezval@gmail.com>
Create a driver to add support for SoC sensors exported by the System
Control Processor (SCP) via the System Control and Power Interface
(SCPI). The supported sensor types is one of voltage, temperature,
current, and power.
The sensor labels and values provided by the SCP are exported via the
hwmon sysfs interface.
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Cc: Sudeep Holla <sudeep.holla@arm.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
NCT6793D is register compatible with NCT6792D.
Also move nct6775_sio_names[] closer to enum kinds to simplify
adding new chips.
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The STEP_UP_TIME and STEP_DOWN_TIME registers are swapped for all chips but
NCT6775.
Reported-by: Grazvydas Ignotas <notasas@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Cc: stable@vger.kernel.org # v3.10+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull thermal updates from Zhang Rui:
- use int instead of unsigned long to represent temperature to avoid
bogus overheat detection when negative temperature reported. From
Sascha Hauer.
- export available thermal governors information to user space via
sysfs. From Wei Ni.
- introduce new thermal driver for Wildcat Point platform controller
hub, which uses PCH thermal sensor and associated critical and hot
trip points. From Tushar Dave.
- add suuport for Intel Skylake and Denlow platforms in powerclamp
driver.
- some small cleanups in thermal core.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: Add Intel PCH thermal driver
thermal: Add comment explaining test for critical temperature
thermal: Use IS_ENABLED instead of #ifdef
thermal: remove unnecessary call to thermal_zone_device_set_polling
thermal: trivial: fix typo in comment
thermal: consistently use int for temperatures
thermal: add available policies sysfs attribute
thermal/powerclamp: add cpu id for denlow platform
thermal/powerclamp: add cpu id for Skylake u/y
thermal/powerclamp: add cpu id for skylake h/s
This patch adds a member (cpu_pwr_sample_ratio) of fam15h_power_data,
that represents the ratio of compute unit power accumulator sample
period to the PTSC counter period.
Tsample: compute unit power accumulator sample period
Tref: the performance timestamp counter period
PTSC: performance timestamp counter
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On Carrizo and later platforms, running_avg_capture bit field is
extended to 4:31 (28 bits) from 4:25.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
We rename fam15h_power_is_internal_node0() function to
should_load_on_this_node(), because it may not be node0 from KV and
on, and they are single-node processors.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
AMD Carrizo(Fam15h, M60h) processors can report power1_crit
(ProcessorPwrWatts) and power1_input (CurrPwrWatts) values.
And this patch adds support for CZ.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some of the LTC chips supported by this driver have to be polled
to ensure that they are ready to accept commands.
Signed-off-by: Michael Jones <mike@proclivis.com>
[Guenter Roeck: simplifications and formatting changes]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
PMBus controllers optionally support PEC. Configure the driver
to use it if available to improve operational security.
Suggested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LTC3886 is a is a dual PolyPhase DC/DC synchronous step-down switching
regulator controller. It is mostly command compatible to LTC3883,
but supports two phases instead of one.
Suggested-by: Michael Jones <mike@proclivis.com>
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LTC2980 and LTM2987 are command compatible to LTC2977. They consist of
two LTC2977 on a single die, and are instantiated as two separate chips,
each supporting eight channels.
Suggested-by: Michael Jones <mike@proclivis.com>
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add additional chip ID for an older revision of LTC2978, as well
as two chip IDs for LTC3882. Turns out the LTC3882 does support the
LTC2978_MFR_SPECIAL_ID register, and reading it returns its chip ID,
but the register is undocumented.
Suggested-by: Michael Jones <mike@proclivis.com>
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Per information from Linear Technologies, the ID mask is 12 bit
for all chips of this series. Use this mask to detect chips to ensure
that all chip revisions are detected.
Suggested-by: Michael Jones <mike@proclivis.com>
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The code used to determine historic low and high peaks is repeated
several times. Introduce helper functions to simplify it.
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It is becoming cumbersom to track per-chip feature support.
Introduce feature flag to simplify the code.
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LTC2975 is mostly compatible to LTC2974, but supports input current
and power measurement.
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Per datasheet, the chip ID for LTM4676 is 0x448x. This was observed
in real systems. In addition to that, chip ID 0x4401 was observed
as well. Research shows that the chip ID has been changed from 0x440x
to 0x448x in datasheet revision C. Add support for the additional chip ID.
Also add the chip ID for LTM4676A, which is functionally identical
to LTM4676.
Reported-by: Ananda Babu Nettam <anandab@juniper.net>
Cc: Ananda Babu Nettam <anandab@juniper.net>
Cc: Amit U Jain <amjain@juniper.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LTC3882 is mostly compatible with LTC3880. Major differences are that it
does not measure the input current, and it no longer supports LTC's legacy
mechanism to identify the chip.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Verifying the chip type is getting more complicated with new chips,
since not all chips support the same mechanism to read the chip type.
Move the code into a separate function to simplify adding support for
those chips.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This change sht15_reverse() to be generic bitrev8().
Signed-off-by: yalin wang <yalin.wang2010@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add device IDs and references for Texas Instruments TPS544B20, TPS544B25,
TPS544C20, and TPS544C25 to the generic PMBus driver.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX20751 is a multiphase power controller with internal buck converter.
It uses VR12.0 to report the output voltage. This requires an explicit
driver, since the VR version can not be auto-detected.
The chip supports a manufacturer specific command to fine-tune the output
voltage. This command is not currently supported.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the IT8732F. This chip is pretty similar to IT8721F,
with the main difference being that the ADC LSB is 10.9 mV instead of
12 mV.
Signed-off-by: Justin Maggard <jmaggard@netgear.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
ADM1293 and ADM1294 are mostly compatible with other chips of the same
series, but have more configuration options. There are also some
differences in register details.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Introduce have_vout, have_vaux_status, have_pin_max, and have_uc_fault
to simplify adding support for new chips.
Also simplify error returns where appropriate to return immediately
on error.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Each new chip supported by the driver has a new set of coefficients,
making hard-coding coefficients more and more cumbersome. Introduce
a datastructure and table to simplify configuration.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
pmbus_regulator_ops is not modified after initialized, so make it const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The pmbus_regulator_ops is for voltage regulators, so explicitly set
regulator type for better readability.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add f81768d (id 0x1210) currently found on Jetway motherboards.
It has 11 voltages but otherwise needed no special handling
in this driver.
Signed-off-by: George Joseph <george.joseph@fairview5.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The temperature value of Fintek F81866 is the same with
f71882fg. It located with 0x6c + 2*(nr), others located
with 0x6c + 2*(nr+1). We change the rule in f71882fg_probe(),
If type = f71858fg/f8000/f81866a. the temp_start will set to 0,
others are 1.
The F81866 over-temperature beep setting is not the same with
f71882fg too. They are using the same address 63H, but F81866 is
using bit 0/1/2 & 4/5/6, others are using bit 1/2/3 & 5/6/7,
So we copy from fxxxx_temp_beep_attr[] to f81866_temp_beep_attr
and change bit setting.
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add New Fintek SuperIO F81866(0x1010) & F71868(0x1106)
with H/W Monitor functions.
We increased F71882FG_MAX_INS from 9 to 10 to read
F71868 10 voltage sets.
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Added fan output control registers.
Modes of operation are PWM (default) and DC.
Introduced show_pwm, store_pwm, nct7802_pwm_attrs, nct7802_pwm_group.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So technically there's no need for a driver to export
the OF table since currently it's not used.
In fact, the I2C device ID table is mandatory for I2C drivers since
a i2c_device_id is passed to the driver's probe function even if the
I2C core used the OF table to match the driver.
And since the I2C core uses different tables, OF-only drivers needs to
have duplicated data that has to be kept in sync and also the dev node
compatible manufacturer prefix is stripped when reporting the MODALIAS.
To avoid the above, the I2C core behavior may be changed in the future
to not require an I2C device table for OF-only drivers and report the
OF module alias. So, it's better to also export the OF table to prevent
breaking module autoloading if that happens.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So the driver needs to export the I2C table and this
be built into the module or udev won't have the necessary information
to auto load the correct module when the device is added.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
CPU fan speed going up and down on Dell Studio XPS 8100 for
unknown reasons. Without further debugging on the affected
machine, it is not possible to find the problem.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=100121
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Jan C Peters <jcpeters89@gmail.com>
Cc: stable@vger.kernel.org # v4.0+, will need backport
[groeck: cleaned up description, comments]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The thermal code uses int, long and unsigned long for temperatures
in different places.
Using an unsigned type limits the thermal framework to positive
temperatures without need. Also several drivers currently will report
temperatures near UINT_MAX for temperatures below 0°C. This will probably
immediately shut the machine down due to overtemperature if started below
0°C.
'long' is 64bit on several architectures. This is not needed since INT_MAX °mC
is above the melting point of all known materials.
Consistently use a plain 'int' for temperatures throughout the thermal code and
the drivers. This only changes the places in the drivers where the temperature
is passed around as pointer, when drivers internally use another type this is
not changed.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Darren Hart <dvhart@linux.intel.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Peter Feuerer <peter@piie.net>
Cc: Punit Agrawal <punit.agrawal@arm.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Peter Feuerer <peter@piie.net>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-acpi@vger.kernel.org
Cc: platform-driver-x86@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-omap@vger.kernel.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: lm-sensors@lm-sensors.org
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Writing a large value into a voltage limit attribute can result
in an overflow due to an auto-conversion from unsigned long to
unsigned int.
Cc: Constantine Shulyupin <const@MakeLinux.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
pwm attributes have well defined names, which should be used.
Cc: Vadim V. Vlasov <vvlasov@dev.rtsoft.ru>
Cc: stable@vger.kernel.org #v4.1+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use kernel.h macro definition.
Thanks to Julia Lawall for Coccinelle scripting support.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Add pwm[4-7] and the associated pwm[4-7]_mode attributes.
Signed-off-by: Roger Lucas <vt8231@hiddenengine.co.uk>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
The mcp3021 scaling code is dividing the VDD (full-scale) value in
millivolts by the A2D resolution to obtain the scaling factor. When VDD
is 3300mV (the standard value) and the resolution is 12-bit (4096
divisions), the result is a scale factor of 3300/4096, which is always
one. Effectively, the raw A2D reading is always being returned because
no scaling is applied.
This patch fixes the issue and simplifies the register-to-volts
calculation, removing the unneeded "output_scale" struct member.
Signed-off-by: Nick Stevens <Nick.Stevens@digi.com>
Cc: stable@vger.kernel.org # v3.10+
[Guenter Roeck: Dropped unnecessary value check]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
As per Documentation/hwmon/sysfs-interface, hwmon name attributes must
not include '-', so replace 'dell-smm' with 'dell_smm'.
Fixes: 039ae58503 ("hwmon: Allow to compile dell-smm-hwmon driver without /proc/i8k")
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Here's the big char/misc driver pull request for 4.2-rc1.
Lots of mei, extcon, coresight, uio, mic, and other driver updates in
here. Full details in the shortlog. All of these have been in
linux-next for some time with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlWNn0gACgkQMUfUDdst+ykCCQCgvdF4F2+Hy9+RATdk22ak1uq1
JDMAoJTf4oyaIEdaiOKfEIWg9MasS42B
=H5wD
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here's the big char/misc driver pull request for 4.2-rc1.
Lots of mei, extcon, coresight, uio, mic, and other driver updates in
here. Full details in the shortlog. All of these have been in
linux-next for some time with no reported problems"
* tag 'char-misc-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (176 commits)
mei: me: wait for power gating exit confirmation
mei: reset flow control on the last client disconnection
MAINTAINERS: mei: add mei_cl_bus.h to maintained file list
misc: sram: sort and clean up included headers
misc: sram: move reserved block logic out of probe function
misc: sram: add private struct device and virt_base members
misc: sram: report correct SRAM pool size
misc: sram: bump error message level on unclean driver unbinding
misc: sram: fix device node reference leak on error
misc: sram: fix enabled clock leak on error path
misc: mic: Fix reported static checker warning
misc: mic: Fix randconfig build error by including errno.h
uio: pruss: Drop depends on ARCH_DAVINCI_DA850 from config
uio: pruss: Add CONFIG_HAS_IOMEM dependence
uio: pruss: Include <linux/sizes.h>
extcon: Redefine the unique id of supported external connectors without 'enum extcon' type
char:xilinx_hwicap:buffer_icap - change 1/0 to true/false for bool type variable in function buffer_icap_set_configuration().
Drivers: hv: vmbus: Allocate ring buffer memory in NUMA aware fashion
parport: check exclusive access before register
w1: use correct lock on error in w1_seq_show()
...
- New driver for Microchip TC74
- Support for ncpXXwf104 added to ntc_thermistor driver
- Minor cleanup
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ZKHZ
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- new driver for Microchip TC74
- support for ncpXXwf104 added to ntc_thermistor driver
- minor cleanup
* tag 'hwmon-for-linus-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: add driver for Microchip TC74
hwmon: (ntc_thermistor) Improve precision of resistance calculation
hwmon: (ntc_thermistor) fix iio raw to microvolts conversion
hwmon: (atxp1) Drop auto-detection
hwmon: (atxp1) Drop FSF mailing address
hwmon: Allow compile test of GPIO consumers if !GPIOLIB
hwmon: (sht15) Constify platform_device_id
hwmon: (max197) Constify platform_device_id
hwmon: (ntc_thermistor) Add support for ncpXXwf104
Add hwmon driver for the Microchip TC74.
The TC74 is a single-input 8-bit I2C temperature sensor,
with +-2 degrees centigrade accuracy.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The function get_ohm_of_thermistor has both the measured voltage and the
pullup voltage available in microvolts. But it was promptly converting
both to millivolts before using them to calculate the thermistor
resistance. That conversion unnecessarily hurt the precision of the
calculation.
For example, take the ncpXXwb473 connected to 5000 mV and pulled down
through a 47000 ohm resistor. At 25 C, the resistance of the thermistor
is 47000 ohms. The measured voltage will be 2500 mV. If we measure
instead 2501 mV, then the calculated resistance will be 46962 ohms --
a difference of 38 ohms. So the precision of the resistance estimate
could be increased by 38X by doing the calculations in microvolts.
Signed-off-by: Chris Lesiak <chris.lesiak@licor.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The function ntc_adc_iio_read was assuming both a 12 bit ADC and that
pullup_uv is the same as the ADC reference voltage. If either
assumption is false, then the result is incorrect.
Attempt to use iio_convert_raw_to_processed to convert the raw value to
microvolts. It will fail for iio channels that don't support support
IIO_CHAN_INFO_SCALE; in that case fall back to the assumptions.
Signed-off-by: Chris Lesiak <chris.lesiak@licor.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Auto-detection for this chip is highly unreliable, and one of its
I2C addresses can also be used by EEPROMs, increasing the risk for
false positives even more. Drop auto-detection entirely to remove
the risk.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The FSF mailing address may change and does not provide any real value.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: lm-sensors@lm-sensors.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch adds support for the ntc thermistor NCPXXWF104 series.
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The following error message is seen when loading the nct6683 driver
with DEBUG_LOCK_ALLOC enabled.
BUG: key ffff88040b2f0030 not in .data!
------------[ cut here ]------------
WARNING: CPU: 0 PID: 186 at kernel/locking/lockdep.c:2988
lockdep_init_map+0x469/0x630()
DEBUG_LOCKS_WARN_ON(1)
Caused by a missing call to sysfs_attr_init() when initializing
sysfs attributes.
Reported-by: Alexey Orishko <alexey.orishko@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Cc: stable@vger.kernel.org # v3.18+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The following error message is seen when loading the nct6775 driver
with DEBUG_LOCK_ALLOC enabled.
BUG: key ffff88040b2f0030 not in .data!
------------[ cut here ]------------
WARNING: CPU: 0 PID: 186 at kernel/locking/lockdep.c:2988
lockdep_init_map+0x469/0x630()
DEBUG_LOCKS_WARN_ON(1)
Caused by a missing call to sysfs_attr_init() when initializing
sysfs attributes.
Reported-by: Alexey Orishko <alexey.orishko@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Cc: stable@vger.kernel.org # v3.12+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
I2C address 0x37 may be used by EEPROMs, which can result in false
positives. Do not attempt to detect a chip at this address.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Cc: stable@vger.kernel.org # v4.0+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The former duplicates the functionality of the latter but is
neither documented nor arch-independent.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Link: http://lkml.kernel.org/r/1432645896-12588-4-git-send-email-bgolaszewski@baylibre.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When configured via device tree, the associated iio device needs to be
measuring voltage for the conversion to resistance to be correct.
Return -EINVAL if that is not the case.
Signed-off-by: Chris Lesiak <chris.lesiak@licor.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch splits CONFIG_I8K compile option to SENSORS_DELL_SMM and CONFIG_I8K.
Option SENSORS_DELL_SMM is now used to enable compilation of dell-smm-hwmon
driver and old CONFIG_I8K option to enable /proc/i8k interface in driver.
So this change allows to compile dell-smm-hwmon driver without legacy /proc/i8k
interface which is needed only for old Dell Inspirion models or for userspace
i8kutils package.
For backward compatibility when CONFIG_I8K is enabled then also SENSORS_DELL_SMM
is enabled and so driver dell-smm-hwmon (with /proc/i8k) is compiled.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit moves i8k driver to hwmon tree under name dell-smm-hwmon which is
better name then abbreviation i8k. For backward compatibility is added macro
MODULE_ALIAS("i8k") so modprobe will load driver also old name i8k. CONFIG_I8K
compile option was not changed.
This commit also adds me as maintainer of this new dell-smm-hwmon driver and
remove Guenter Roeck from list who is implicit maintainer all hwmon drivers.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace the loop iterating over pwm_freq_cksel0 with a call to
find_closest_descending().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use find_closest() to locate the closest average in ina226_avg_tab.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
pwm_config() must be called with a duty cycle of 0 prior to calling
pwm_disable() to ensure that the pwm signal is set to low.
Reported-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Feature macros work on sio_data as well, so use them there.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix
drivers/hwmon/ibmpowernv.c: In function 'get_logical_cpu':
drivers/hwmon/ibmpowernv.c:121:3:
error: implicit declaration of function 'get_hard_smp_processor_id'
seen for some configurations, possibly if SMP is not configured.
Fixes: 3df2f59f0a ("hwmon: (ibmpowernv) pretty print labels")
Cc: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The new OPAL device tree adds a few properties which can be used to add
extra information on the sensor label.
In the case of a cpu core sensor, the firmware exposes the physical
identifier of the core in the "ibm,pir" property. The driver
translates this identifier in a linux cpu number and prints out a
range corresponding to the hardware threads of the core (as they
share the same sensor).
The numbering gives a hint on the localization of the core in the
system (which socket, which chip).
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Currently, sensors are only identified by their type and index.
The new OPAL device tree can expose extra properties to identify
some sensors by their name or location. This patch adds the creation
of a new hwmon *_label attribute when such properties are detected.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The new OPAL device tree for sensors has a different layout and uses new
property names, for the type and for the handler used to capture the
sensor data.
This patch modifies the ibmpowernv driver to support such a tree in a
way preserving compatibility with older OPAL firmwares.
This is achieved by changing the error path of the routine parsing
an OPAL node name. The node is simply considered being from the new
device tree layout and fallback values are used.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This should shorten a bit the code necessary to create a hmwon attribute.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
IT8620E is mostly compatible to IT7828F. Add generic support for it.
IT8620E supports up to 6 fan tachometers and 6 pwm controls.
Support for the 6th tachometer and for the additional pwm controls
are addded in separate patches.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
IT8790E is a super-IO chip with three fan tachometers. It is mostly
compatible to IT8728F, but only supports three fan tachometers
instead of five.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On some chips, in7 is always an internal voltage sensor. Introduce
feature flag to reflect this condition to simplify adding support
for new chips.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
ITE chips may have 'E', 'F', or both 'E' and 'F' suffixes.
Introduce suffic configuration to the it87_devices structure
to simplify adding new chips.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On chips with newer PWM control, the PWM frequency divider is 256
instead of 128. Since the base PWM frequency remained the same, the actual
PWM frequency is half of what it used to be with the older PWM control
mechanism.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Detection if a pwm channel is supported was wrong on removal,
causing the code to try removing non-existing sysfs attributes.
That didn't matter much because sysfs attribute removal of non-existing
files fails silently, and because the wrong evaluation always returned
false, but should nevertheless be fixed.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The current OPAL firmware exposes the different sensors of an IBM Power
system using node names such as :
sensors/amb-temp#1-data
sensors/amb-temp#1-thrs
cooling-fan#1-data
cooling-fan#1-faulted
cooling-fan#1-thrs
cooling-fan#2-data
...
The ibmpowernv driver, when loaded, parses these names to extract the
sensor index and the sensor attribute name. Unfortunately, this scheme
makes it difficult to add sensors with a different layout (specially of
the same type, like temperature) as the sensor index calculated in OPAL
is directly used in the hwmon sysfs interface.
What this patch does is add a independent hwmon index for each sensor.
The increment of the hwmon index (temp, fan, power, etc.) is kept per
sensor type in the sensor_group table. The sensor_data table is used
to store the association of the hwmon and OPAL indexes, as we need to
have the same hwmon index for different attributes of a same sensor.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It simplifies the creation of the hwmon attributes and will help when
support for a new device tree layout is added. The patch also changes
the name of the routine to parse_opal_node_name().
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It simplifies the create_hwmon_attr_name() routine and it clearly isolates
the conversion done between the OPAL node names and hwmon attributes names.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It will help in adding different compatible properties, coming from a
new device tree layout for example.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Ambient is too restrictive as there can be other temperature channels :
core, memory, etc.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Auxiliary fan monitoring is not enabled on ASRock Z77 Pro4-M
with BIOS version 2.00 if booted in UEFI Ultra-FastBoot mode.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
After a suspend/resume cycle it is not guaranteed that the hardware monitoring
device is still enabled. Ensure that this is the case after resume.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Get rid of #ifdef CONFIG_PM by using SIMPLE_DEV_PM_OPS and declaring suspend
and resume functions with __maybe_unused.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix build error when CONFIG_THERMAL=m and SENSORS_GPIO_FAN=y
by preventing that combination.
Fixes these build errors:
drivers/built-in.o: In function `gpio_fan_remove':
gpio-fan.c:(.text+0x21e97e): undefined reference to `thermal_cooling_device_unregister'
drivers/built-in.o: In function `gpio_fan_probe':
gpio-fan.c:(.text+0x21efbc): undefined reference to `thermal_cooling_device_register'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: lm-sensors@lm-sensors.org
Cc: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix build errors when CONFIG_THERMAL=m and SENSORS_PWM_FAN=y
by restricting SENSORS_PWM_FAN to 'm' when THERMAL=m.
drivers/built-in.o: In function `pwm_fan_remove':
pwm-fan.c:(.text+0x22ba58): undefined reference to `thermal_cooling_device_unregister'
drivers/built-in.o: In function `pwm_fan_probe':
pwm-fan.c:(.text+0x22bebb): undefined reference to `thermal_of_cooling_device_register'
pwm-fan.c:(.text+0x22bf11): undefined reference to `thermal_cdev_update'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Address the following sparse warnings.
drivers/hwmon/pwm-fan.c:176:5: warning:
symbol 'pwm_fan_of_get_cooling_data' was not declared. Should it be static?
drivers/hwmon/pwm-fan.c:176:5: warning:
no previous prototype for 'pwm_fan_of_get_cooling_data'
pwm_fan_of_get_cooling_data is only used in the pwm-fan driver and thus should
be declared static.
Cc: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Allow gpio-fan to be used as thermal cooling device for platforms that
use GPIO maps to control fans.
As part of this change, we make the shutdown and remove logic the same
as well.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The PWM FAN device can now be used as a thermal cooling device.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch provides code for reading PWM FAN configuration data via
device tree. The pwm-fan can work with full speed when configuration
is not provided. However, errors are propagated when wrong DT bindings
are found.
Additionally the struct pwm_fan_ctx has been extended.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It was necessary to decouple code handling writing to sysfs from the one
responsible for setting PWM of the fan.
Due to that, new __set_pwm() method was extracted, which is responsible for
only setting new PWM duty cycle.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On some boards, such as the LaCie 2Big Network v2 or 2Big NAS (based on
Marvell Kirkwood SoCs), an I2C fan controller is used but the alarm
signal is wired to a separate GPIO. Unfortunately, the gpio-fan driver
can't be used to handle GPIO alarm alone from DT: an error is returned
if the "gpios" DT property is missing.
This patch allows to use the gpio-fan driver even if the "alarm-gpios"
DT property is defined alone.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The bank register has five unused bits. Verify that those bits are zero
to strengthen the detect function.
Cc: Vadim V. Vlasov <vvlasov@dev.rtsoft.ru>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
The NCT7904D is a hardware monitor supporting up to 20 voltage sensors,
internal temperature sensor, Intel PECI and AMD SB-TSI CPU temperature
interface, up to 12 fan tachometer inputs, up to 4 fan control channels
with SmartFan.
Signed-off-by: Vadim V. Vlasov <vvlasov@dev.rtsoft.ru>
[Guenter Roeck: Fixed whitespace errors, dropped redundant comment]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
IT8603 only supports three fans, so it is not necessary to skip fan4.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
IT8786E is mostly compatible with IT8771 / IT8772.
Parameters determined by testing various combinations.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Thomas Lorblanches <zlika_ese@hotmail.com>
[Guenter Roeck: merged from github, addressed review comments]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Newer chips don't typically support VID inputs or control.
Add a feature flag for VID support to simplify adding support for
new chips.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fans 4-5 are not supported on all chips and revisions. Also, 16-bit fan
counters are always enabled on some chips. Provide feature flags to
simplify adding support for new chips.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On IT8728F, IT8771E, and IT8772E, fans counters are always 16 bit
and don't need to be configured for it.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
TS3000GB0 has a new device ID (0x2913). Since IDT's datasheets suggest
that the upper 8 bit of the device ID reflect the chip ID and the lower
8 bit reflect the version number, modify the code to accept all chips
with ID 0x29xx.
Also add support for TS3001 and TSE2004.
Some of the datasheets for older chips are no longer available from
the IDT web site, so replace explicit links in the documentation with
a generic note.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
IT8781F is mostly compatible to IT8782F. Major difference is that it only
supports four instead of six UART channels, and therefore does not share
the uart6 pins.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The only difference between the three power_sensor_name_templates is
whether there is a suffix of "", "_lowest" or "_highest". We might as
well pull those into an array and use a literal format string,
allowing gcc to do type checking of the arguments to
sprintf. Incidentially, the same three suffixes are used in the
temp_sensor_name_templates case, so we end up eliminating one static
array.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
[Guenter Roeck: Fixed line length over 80 characters]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
By extracting the only part that differs we can allow static checking
of the format string, and possibly save a little .rodata.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
[Guenter Roeck: continuation line alignment]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
devm_regmap_init_i2c() can fail, thus add return value checking.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull kconfig updates from Michal Marek:
"Yann E Morin was supposed to take over kconfig maintainership, but
this hasn't happened. So I'm sending a few kconfig patches that I
collected:
- Fix for missing va_end in kconfig
- merge_config.sh displays used if given too few arguments
- s/boolean/bool/ in Kconfig files for consistency, with the plan to
only support bool in the future"
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kconfig: use va_end to match corresponding va_start
merge_config.sh: Display usage if given too few arguments
kconfig: use bool instead of boolean for type definition attributes
Setting a dev_pm_ops suspend/resume pair but not a set of
hibernation functions means those pm functions will not be
called upon hibernation.
Fix this by using SIMPLE_DEV_PM_OPS, which appropriately
assigns the suspend and hibernation handlers and move
mp102_suspend/tmp102_resume under CONFIG_PM_SLEEP to avoid
build warnings.
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
[groeck: Declare tmp102_dev_pm_ops as static variable]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The variables diff_input, ext_vref, and vref_mv are only used in the probe
function and therefore don't need to be kept in the device data structure.
Reviewed-and-Tested-by: Robert Rosengren <robert.rosengren@axis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Simplify code and reduce code size by using regmap to access i2c registers.
Reviewed-and-Tested-by: Robert Rosengren <robert.rosengren@axis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver supports negative high and critical limits, it can return
negative hysteresis values, so there is no good reason to not let the
user write negative hysteresis values.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
data->temp[index] has type s16. Because of C's promotion rules,
(data->temp[index] << 7) >> 7 is exactly the same as
data->temp[index]. The intention was to use bit 8 as a sign bit, so do
that using the existing API.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The comment above (data << 2) >> 2 explains what the intention is: To
use bit 13 of the 14-bit value data as the sign bit. However, this
doesn't work due to C's promotion rules. data has type s16, but data
<< 2 has type int. To get sign extension, that expression would have
to be cast back to an s16 before being shifted (at which point C's
promotion rules would then kick in again and promote the left operand
to int). As it stands, both expressions are no-ops for any value of
data.
Avoid these subtleties by using the existing API for
this. sign_extend32 works equally well for 8 and 16 bit types.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fixed the following warnings (reported by cppcheck):
[drivers/hwmon/abx500.c:224]: (warning) %ld in format string (no. 1)
requires 'long' but the argument type is 'unsigned long'.
[drivers/hwmon/abx500.c:233]: (warning) %ld in format string (no. 1)
requires 'long' but the argument type is 'unsigned long'.
[drivers/hwmon/abx500.c:242]: (warning) %ld in format string (no. 1)
requires 'long' but the argument type is 'unsigned long'.
Signed-off-by: Asaf Vertz <asaf.vertz@tandemg.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Subtracting an unsigned long from a signed value causes an overflow with large
values. Use clamp_val() to reduce the number range prior to subtracting it
from the temperature limit.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Mixed use of long and int caused an integer overflow when writing large limits.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Despite the name, sign_extend32 works just fine for 16 bit variables,
so it is safe to use.
Cc: Martin Kepplinger <martink@posteo.de>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for "ina231" as compatible string, and update
Documentation and Kconfig accordingly.
Tested with the Exynos5422-based odroid-xu3 board which has on-board
INA231 sensors.
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DIV_ROUND_CLOSEST() when dealing with the calibration values to make the
calculations less error prone.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This attribute allows to configure the update interval of ina226. Although
the bus and shunt voltage conversion times remain hardcoded to 1.1 ms, we can
now modify said interval by changing the averaging rate.
While we're at it - add an additional variable to ina2xx_data, which holds
the current configuration settings - this way we'll be able to restore the
configuration in case of an unexpected chip reset.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The shunt resistance can only be set via platform_data or device tree. This
isn't suitable for devices in which the shunt resistance can change/isn't
known at boot-time.
Add a sysfs attribute that allows to read and set the shunt resistance.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Shunt resistance values greater than the chip's calibration factor make no
sense since the actual value written to the register equals:
<calibration factor> / <shunt>
Bail-out from ina2xx_probe() if the configured value is greater than the
calibration factor.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Chips from the ina family don't like to be uninitialized. In case the power
is cut-off and restored again the calibration register will be reset
to 0 and both the power and current registers will remain at 0.
Check the calibration register in ina2xx_update_device() and reinitialize
the chip if needed.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use module_pci_driver to simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
On many motherboards, for an unknown reason, the thermal sensor seems
to be disabled and will return a constant temperature value of 36.5
degrees Celsius. Don't bind to the device in that case, so that we
don't report this bogus value to userspace.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Romain Dolbeau <romain@dolbeau.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Use devm_hwmon_device_register_with_groups() to simplify the code a
bit.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Romain Dolbeau <romain@dolbeau.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
The Intel 5500, 5520 and X58 chipsets embed a digital thermal sensor.
This new driver supports it.
Note that on many boards the sensor seems to be disabled and reports
the minimum value (36.5 degrees Celsius) all the time.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Romain Dolbeau <romain@dolbeau.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Support for keyword 'boolean' will be dropped later on.
No functional change.
Reference: http://lkml.kernel.org/r/cover.1418003065.git.cj@linux.com
Signed-off-by: Christoph Jaeger <cj@linux.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Pull thermal management update from Zhang Rui:
"Summary:
- of-thermal extension to allow drivers to register and use its
functionality in a better way, without exploiting thermal core.
From Lukasz Majewski.
- Fix a bug in intel_soc_dts_thermal driver which calls a sleep
function in interrupt handler. From Maurice Petallo.
- add a thermal UAPI header file for exporting the thermal generic
netlink information to user-space. From Florian Fainelli.
- First round of refactoring in Exynos driver. Bartlomiej and Lukasz
are attempting to make it lean and easier to understand.
- New thermal driver for Rockchip (rk3288), with support for DT
thermal. From Caesar Wang.
- New thermal driver for Nvidia, Tegra124 SOCTHERM driver, with
support for DT thermal. From Mikko Perttunen.
- New cooling device, based on common clock framework. From Eduardo
Valentin.
- a couple of small fixes in thermal core framework. From Srinivas
Pandruvada, Javi Merino, Luis Henriques.
- Dropping Armada A375-Z1 SoC thermal support as the chip is not in
the market, armada folks decided to drop its support.
- a couple of small fixes and cleanups in int340x thermal driver"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (58 commits)
thermal: provide an UAPI header file
Thermal/int340x: Clear the error value of the last acpi_bus_get_device() call
thermal/powerclamp: add id for braswell cpu
thermal: Intel SoC DTS: Don't do thermal zone update inside spin_lock
Thermal: fix platform_no_drv_owner.cocci warnings
Thermal/int340x: avoid unnecessary pointer casting
thermal: int3403: Delete a check before thermal_zone_device_unregister()
thermal/int3400: export uuids
thermal: of: Extend current of-thermal.c code to allow setting emulated temp
thermal: of: Extend of-thermal to export table of trip points
thermal: of: Rename struct __thermal_trip to struct thermal_trip
thermal: of: Extend of-thermal.c to provide check if trip point is valid
thermal: of: Extend of-thermal.c to provide number of trip points
thermal: Fix error path in thermal_init()
thermal: lock the thermal zone when switching governors
thermal: core: ignore invalid trip temperature
thermal: armada: Remove support for A375-Z1 SoC
thermal: rockchip: add driver for thermal
dt-bindings: document Rockchip thermal
thermal: exynos: remove exynos_tmu_data.h include
...
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
TMP435 supports a range of I2C addresses, not just 0x4c.
Cc: Patrick Titiano <ptitiano@baylibre.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
A chip returning 0x00 in all registers is erroneously detected
as LM75. Check hysteresis and temperature limit registers and
abort if both are 0 to reduce the likelyhood for this to happen.
Reviewed-by: Rob Coulson <rob.coulson@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Poweroff the fans when shutting down the system. Else,
echo '1' > /sys/class/hwmon/hwmon0/fan1_target; poweroff leaves the
fan running if the System power off does not drive the gpio expander
which might control the fan power supply.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Certain I2C based GPIO expanders could be used in sleepable context,
this results in:
[ 115.890569] ------------[ cut here ]------------
[ 115.895422] WARNING: CPU: 0 PID: 1115 at drivers/gpio/gpiolib.c:1370 gpiod_set_raw_value+0x40/0x4c()
[ 115.905024] Modules linked in:
[ 115.908229] CPU: 0 PID: 1115 Comm: sh Tainted: G W 3.18.0-rc7-next-20141203-dirty #1
[ 115.917461] Hardware name: Generic DRA74X (Flattened Device Tree)
[ 115.923876] [<c0015368>] (unwind_backtrace) from [<c00119f4>] (show_stack+0x10/0x14)
[ 115.932013] [<c00119f4>] (show_stack) from [<c05b78e8>] (dump_stack+0x78/0x94)
[ 115.939594] [<c05b78e8>] (dump_stack) from [<c003de28>] (warn_slowpath_common+0x7c/0xb4)
[ 115.948094] [<c003de28>] (warn_slowpath_common) from [<c003de7c>] (warn_slowpath_null+0x1c/0x24)
[ 115.957315] [<c003de7c>] (warn_slowpath_null) from [<c03461e8>] (gpiod_set_raw_value+0x40/0x4c)
[ 115.966457] [<c03461e8>] (gpiod_set_raw_value) from [<c04866f4>] (set_fan_speed+0x4c/0x64)
[ 115.975145] [<c04866f4>] (set_fan_speed) from [<c04868a8>] (set_rpm+0x98/0xac)
[ 115.982742] [<c04868a8>] (set_rpm) from [<c039fb4c>] (dev_attr_store+0x18/0x24)
[ 115.990426] [<c039fb4c>] (dev_attr_store) from [<c01b0a28>] (sysfs_kf_write+0x4c/0x50)
[ 115.998742] [<c01b0a28>] (sysfs_kf_write) from [<c01afe1c>] (kernfs_fop_write+0xbc/0x19c)
[ 116.007333] [<c01afe1c>] (kernfs_fop_write) from [<c0148cc4>] (vfs_write+0xb0/0x1a0)
[ 116.015461] [<c0148cc4>] (vfs_write) from [<c0148fbc>] (SyS_write+0x44/0x84)
[ 116.022881] [<c0148fbc>] (SyS_write) from [<c000e5c0>] (ret_fast_syscall+0x0/0x48)
[ 116.030833] ---[ end trace 3a0b636123acab82 ]---
So, switch over to sleepable GPIO operations as there is no mandatory
need for non-sleepable gpio operations in the fan driver.
This allows the fan driver to be used with i2c based gpio expanders such
as palmas_gpio.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The return value of i2c_smbus_read_byte_data() is checked in
tmp401_init_client(), but only a warning is printed and the device is
registered anyway. This leads to devices being registered even if they
cannot be physically detected.
Bail out from probe in case of write errors and notify the user.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LM95233 is similar to LM95234, but it only supports two
instead of four external temperature sensors.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LM95235 is register compatible to LM95245.
Also update link to LM95245 data sheet, and drop the link to the
datasheet from the driver source to simplify code maintenance.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The return value of i2c_smbus_write_word_swapped() isn't checked in
ina2xx_probe(). This leads to devices being registered even if they cannot
be physically detected (e.g. device is not powered-up at boot-time).
Even after restoring power to such device, it is left unconfigured as the
configuration has never been actually written to the register.
Error out in case of write errors in probe and notify the user.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
[Guenter Roeck: Fixed multi-line comment style]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
checkpatch complains about
WARNING: Missing a blank line after declarations
Add missing blank lines. Also reorder variables length-wise where appropriate
if a function header is touched anyway.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
NCT6792D is similar to NCT6791D. Only beep control and temperature
monitoring registers are different.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It is basically a faster lm75 with improved (11 bit) resolution.
Signed-off-by: Michael Thalmeier <michael.thalmeier@hale.at>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The current driver probe() function assumes the sensor device to be
always present and gets executed every time if the driver is loaded,
but the appropriate hardware could not be present.
So, move the platform device creation as part of platform init code
and use the 'id_table' to check if the device is present or not.
Signed-off-by: Neelesh Gupta <neelegup@linux.vnet.ibm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The iio subsystem supports humidity sensors, so it makes sense
to support it in the iio-hwmon bridge as well.
Cc: Jonathan Cameron <jic23@kernel.org>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add simple on/off regulator support for ltc2978 and
other pmbus parts supported by the ltc2978 driver.
Signed-off-by: Alan Tull <atull@opensource.altera.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for simple on/off control of each channel.
To add regulator support, the pmbus part driver needs to add
regulator_desc information and number of regulators to its
pmbus_driver_info struct.
regulator_desc can be declared using default macro for a
regulator (PMBUS_REGULATOR) that is in pmbus.h
The regulator_init_data can be initialized from either
platform data or the device tree.
Signed-off-by: Alan Tull <atull@opensource.altera.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Different drivers request API extensions in of-thermal. For this reason,
additional callbacks are required to fit the new drivers needs.
The current API implementation expects the registering sensor driver
to provide a get_temp and get_trend callbacks as function parameters.
As the amount of callbacks is growing, this patch changes the existing
implementation to use a .ops field to hold all the of thermal callbacks
to sensor drivers.
This patch also changes the existing of-thermal users to fit the new
API design. No functional change is introduced in this patch.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: devicetree@vger.kernel.org
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jean Delvare <jdelvare@suse.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Cc: lm-sensors@lm-sensors.org
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Mikko Perttunen <mikko.perttunen@kapsi.fi>
Reviewed-by: Mikko Perttunen <mikko.perttunen@kapsi.fi>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
g762_remove() needs to first call hwmon_device_unregister() and then
g762_of_clock_disable(). For that reason, it is not possible to
convert it to devm_hwmon_device_register_with_groups() and the
the non device managed version must be used.
This is correctly stated in commit message for 398e16db62 ("hwmon:
(g762) Convert to hwmon_device_register_with_groups") but the
associated changes do in fact introduce a call to the device managed
version of the function.
This patch fixes that typo by switching to the non devm_ version.
Fixes: 398e16db62 ("hwmon: (g762) Convert to hwmon_device_register_with_groups")
Cc: stable@vger.kernel.org (3.17+)
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
F3 device ID is wrongly included in fam15h_power_id_table
for F16h M30h. It should be F4 device ID. Fix this.
Signed-off-by: Aravind Gopalakrishnan <aravind.gopalakrishnan@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The state of a PWM output is not clearly defined after resume. Some PWM
drivers do not restore the duty cycle upon resume, thus it is necessary to
manually restore the correct value.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Because we build kernels with drivers built in for many platforms, it's
normal for the ibmpowernv driver to be loaded on systems that don't have
the appropriate hardware.
Currently the driver spams the log with:
ibmpowernv ibmpowernv.0: Opal node 'sensors' not found
ibmpowernv: Platfrom driver probe failed
But there is no error, this machine is not a powernv and doesn't have
the hardware. So change the sensors message to dev_dbg(), and only print
an error about the probe failing if it's not ENODEV.
Also fix the spelling of "Platfrom" and print the actual error value.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Include linux/err.h to get the definitions for IS_ERR() PTR_ERR() and
ERR_PTR() used in the driver.
This fixes compilation on powerpc targets.
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@men.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Drivers should not call pm_power_off directly; it is not guaranteed
to be non-NULL. Call kernel_power_off instead.
Cc: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Added driver to support the 14F021P00 BMC Hardware Monitoring.
The BMC is a Board Management Controller including monitoring of the
board voltages.
Signed-off-by: Andreas Werner <andreas.werner@men.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
To get more comprehensive and integrated thermal management, it adds ntc
thermistor to thermal framework as a thermal sensor. It's governed thermal
susbsystem only if it is described in DT node. Otherwise, it just notifies
temperature to userspace via sysfs as it used to be.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use devm_hwmon_device_register_with_groups() to simplify the code
and reduce code size.
Cc: Clemens Ladisch <clemens@ladisch.de>
Tested-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch adds temperature monitoring support for F15h M60h processor.
- Add new pci device id for the relevant processor
- The functionality of REG_REPORTED_TEMPERATURE is moved to
D0F0xBC_xD820_0CA4 [Reported Temperature Control]
- So, use this to get CUR_TEMP value
- Since we need an indirect register access, protect this with
a mutex lock
- Add Kconfig, Doc entries to indicate support for this processor.
Signed-off-by: Aravind Gopalakrishnan <aravind.gopalakrishnan@amd.com>
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
[Guenter Roeck: Declare new mutex and function static]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
tmp103 temperature sensor driver registers with the hwmon framework by calling
hwmon_device_register_with_groups but does not have a .remove method to call
hwmon_device_unregister to unregister from the framework when the device is no
longer needed. Fix this by calling devm_hwmon_device_register_with_groups.
Signed-off-by: Sundar J Dev <sundarjayakumardev@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
power1_input should only be reported for Fam15h, Models 00h-0fh
So, introduce a is_visible function to take care of this.
As suggested by Guenter here:
http://marc.info/?l=linux-kernel&m=141038145616437&w=2
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Fixes: 22e32f4f57 ('x86,AMD: Power driver support for AMD's family 16h processors')
Signed-off-by: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
After the conversion rate is changed, the zbits are not updated,
but should be, since they are used later in the set_temp function.
Fixes: a50d9a4d9a ("hwmon: (ds1621) Fix temperature rounding operations")
Reported-by: Murat Ilsever <murat.ilsever@gmail.com>
Signed-off-by: Robert Coulson <rob.coulson@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since commit b42261078a ("regmap: i2c: fallback to SMBus if the adapter
does not support standard I2C"), regmap-i2c will check the
I2C_FUNC_SMBUS_[BYTE|WORD]_DATA functionality based on the regmap_config
setting if the adapter does not support standard I2C.
So remove the I2C_FUNC_SMBUS_BYTE_DATA functionality check in the driver code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The DEFINE_SIMPLE_ATTRIBUTE macro should not end in a ; Fix the one use
in the kernel tree that did not have a semicolon.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
vrm is an u8, so the written value needs to be limited to [0, 255].
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
vrm is an u8, so the written value needs to be limited to [0, 255].
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
vrm is an u8, so the written value needs to be limited to [0, 255].
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
vrm is an u8, so the written value needs to be limited to [0, 255].
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
vrm is an u8, so the written value needs to be limited to [0, 255].
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
vrm is an u8, so the written value needs to be limited to [0, 255].
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
vrm is an u8, so the written value needs to be limited to [0, 255].
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
vrm is an u8, so the written value needs to be limited to [0, 255].
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
vrm is an u8, so the written value needs to be limited to [0, 255].
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The hih6130->write_length setting was accidently removed by commit
ebc6b9383f3e "hwmon: (hih6130) Convert to devm_hwmon_device_register_with_groups",
fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On platforms with sizeof(int) < sizeof(long), writing a temperature
limit larger than MAXINT will result in unpredictable limit values
written to the chip. Avoid auto-conversion from long to int to fix
the problem.
Voltage limits, fan minimum speed, pwm frequency, pwm ramp rate, and
other attributes have the same problem, fix them as well.
Zone temperature limits are signed, but were cached as u8, causing
unepected values to be reported for negative temperatures. Cache as
s8 to fix the problem.
vrm is an u8, so the written value needs to be limited to [0, 255].
Signed-off-by: Axel Lin <axel.lin@ingics.com>
[Guenter Roeck: Fix zone temperature cache]
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Temperature limit range is [-127, 127], not [-127, 128].
The wrong range caused a bad limit to be written into the chip
if the limit was set to a value of 128 degrees C or above.
Also use DIV_ROUND_CLOSEST instead of a plain divide operation
to reduce the rounding error when writing temperature limits.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Current code uses data_rate as array index in ads1015_read_adc() and uses pga
as array index in ads1015_reg_to_mv, so we must make sure both data_rate and
pga settings are in valid value range.
Return -EINVAL if the setting is out-of-range.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On platforms with sizeof(int) < sizeof(long), writing a temperature
limit larger than MAXINT will result in unpredictable limit values
written to the chip. Avoid auto-conversion from long to int to fix
the problem.
The hysteresis temperature range depends on the value of
data->temp[attr->index], since val is subtracted from it.
Use a wider clamp, [-120000, 220000] should do to cover the
possible range. Also add missing TEMP_TO_REG() on writes into
cached hysteresis value.
Also uses clamp_val to simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
[Guenter Roeck: Fixed double TEMP_TO_REG on hysteresis updates]
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull timer and time updates from Thomas Gleixner:
"A rather large update of timers, timekeeping & co
- Core timekeeping code is year-2038 safe now for 32bit machines.
Now we just need to fix all in kernel users and the gazillion of
user space interfaces which rely on timespec/timeval :)
- Better cache layout for the timekeeping internal data structures.
- Proper nanosecond based interfaces for in kernel users.
- Tree wide cleanup of code which wants nanoseconds but does hoops
and loops to convert back and forth from timespecs. Some of it
definitely belongs into the ugly code museum.
- Consolidation of the timekeeping interface zoo.
- A fast NMI safe accessor to clock monotonic for tracing. This is a
long standing request to support correlated user/kernel space
traces. With proper NTP frequency correction it's also suitable
for correlation of traces accross separate machines.
- Checkpoint/restart support for timerfd.
- A few NOHZ[_FULL] improvements in the [hr]timer code.
- Code move from kernel to kernel/time of all time* related code.
- New clocksource/event drivers from the ARM universe. I'm really
impressed that despite an architected timer in the newer chips SoC
manufacturers insist on inventing new and differently broken SoC
specific timers.
[ Ed. "Impressed"? I don't think that word means what you think it means ]
- Another round of code move from arch to drivers. Looks like most
of the legacy mess in ARM regarding timers is sorted out except for
a few obnoxious strongholds.
- The usual updates and fixlets all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (114 commits)
timekeeping: Fixup typo in update_vsyscall_old definition
clocksource: document some basic timekeeping concepts
timekeeping: Use cached ntp_tick_length when accumulating error
timekeeping: Rework frequency adjustments to work better w/ nohz
timekeeping: Minor fixup for timespec64->timespec assignment
ftrace: Provide trace clocks monotonic
timekeeping: Provide fast and NMI safe access to CLOCK_MONOTONIC
seqcount: Add raw_write_seqcount_latch()
seqcount: Provide raw_read_seqcount()
timekeeping: Use tk_read_base as argument for timekeeping_get_ns()
timekeeping: Create struct tk_read_base and use it in struct timekeeper
timekeeping: Restructure the timekeeper some more
clocksource: Get rid of cycle_last
clocksource: Move cycle_last validation to core code
clocksource: Make delta calculation a function
wireless: ath9k: Get rid of timespec conversions
drm: vmwgfx: Use nsec based interfaces
drm: i915: Use nsec based interfaces
timekeeping: Provide ktime_get_raw()
hangcheck-timer: Use ktime_get_ns()
...
On platforms with sizeof(int) < sizeof(long), writing a temperature
limit larger than MAXINT will result in unpredictable limit values
written to the chip. Avoid auto-conversion from long to int to fix
the problem.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On platforms with sizeof(int) < sizeof(unsigned long), writing a rpm value
larger than MAXINT will result in unpredictable limit values written to the
chip. Avoid auto-conversion from unsigned long to int to fix the problem.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Simplify the code a bit and also improve readability.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Neelesh Gupta <neelegup@linux.vnet.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use devm_hwmon_device_register_with_groups() to simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver won't instantiate if OF is not configured, thus add OF dependency.
Also add COMPILE_TEST to increase build testing coverage.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The dev_set_drvdata() call is equivalent to the platform_set_drvdata() call in
next line.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
num_attr_groups is only used in nct6775_probe(), make it to be local variable.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver also supports NCT6106D and NCT6791D, thus update module description
and Kconfig accordingly.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and hwmon_device_register_with_groups() to simplify
the code a bit.
Use hwmon_device_register_with_groups rather than the device managed version to
ensure g762_of_clock_disable() is called after hwmon_device_unregister().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use devm_hwmon_device_register_with_groups() to simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use devm_hwmon_device_register_with_groups() to simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use devm_hwmon_device_register_with_groups() to simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The pwm-fan driver enables control of fans connected to PWM lines.
This driver uses the PWM framework, so it is compatible with all
PWM devices that provide drivers through the PWM framework.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Reviewed-by: Tobias Klauser <tklauser@distanz.ch>
[Guenter Roeck: Last argument to devm_of_pwm_get is pointer, use NULL]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Map tables are never changed, so it is safe to make them const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: George Joseph <george.joseph@fairview5.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Punit Agrawal