Extract DMA channels directly from DT as they can not be found from
platform resources anymore. This is a work-around until davinci audio
driver is updated to use dmaengine.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds a separate register location for data port registers to
mcasp DT bindings. On am33xx SoCs the McASP registers are mapped
trough L4 interconnect, but data port registers are also mapped trough
L3 bus to a different memory location.
Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds S/PDIF input/output for mvebu DT boards.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mark Brown <broonie@linaro.org>
While reporting the jack status snd_soc_jack_report() invokes snd_soc_dapm_sync()
always. This should be required when we have pins associated with jack and
reporting enables or disables these.
So add a check for this case
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
... which was introduced by the previous commit a4e9a38b, causing
build errors without CONFIG_PROC_FS.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds codec ID (0x80862882) and module alias for
Valleyview2 display codec.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The conversion of the si476x to regmap removed locking of the core during
register updates, allowing things like power state changes for the MFD to
happen during a register update. Avoid this by taking the core lock in the
DAI operations (which are the only things that do register updates) as we
used to do in the open coded register I/O functions.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Andrey Smirnov <andrew.smirnov@gmail.com>
At the moment, this driver supports only playback, while FFADO supports
(only) full-duplex devices. So, prevent conflicts by not claiming
devices that would be better handled by FFADO.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
While most DICE devices keep TCAT's default category ID of 0x04, Weiss
devices identify themselves with 0x00.
Reported-by: Rolf Anderegg <rolf.anderegg@weiss.ch>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Doing accesses without quadlet alignment is a bad idea because the
firmware's byte-swapping would garble the data; clarify this in the
documentation.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Instead of relying of some control panel application to configure some
fixed sample rate, allow applications to set it automatically.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
In preparation for sample rate selection support, read the stream
parameters that might change when running at different sample rates.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
In preparation for sample rate selection support, ensure that the driver
knows about the device's clock capabilities.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Avoid a lock inversion between dice->mutex and pcm->open_mutex.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Since commit f2b3614cef (Don't check DMA time-out too shortly), we
need no longer to restrict the period length to less than 10 s.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
When a bus reset happens, the enable register is automatically cleared,
so we do not need to clear it manually when stopping the stream.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Add a flag to snd_fw_transaction() to allow it to abort when a bus reset
happens. This removes most of the duplicated error handling loops that
were required around calls to the low-level fw_run_transaction().
Also add a flag to suppress error messages; errors are expected when we
attempt to clean up after the device was unplugged.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Change the AMDTP streaming code to handle the non-standard stream format
that DICE devices use at sample rates greater than 96 kHz.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
DICE devices do not have a unique specifier ID in their unit directory
(it's always the same as the device vendor's ID), so rely on just the
version ID for driver loading, and use a heuristic in the probe callback
to detect actual DICE devices.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Introduce the helper function amdtp_out_stream_running(). This makes
many checks in amdtp.c clearer and frees the device drivers from having
to track this with a separate variable.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
When aborting a PCM stream, the xrun is signaled only if the stream is
running. When disconnecting a PCM stream, calling snd_card_disconnect()
too early would change the stream into a non-running state and thus
prevent the xrun from being noticed by user space.
To prevent this, move the snd_card_disconnect() call after the xrun.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Allow AMDTP output streams to use blocking mode.
Use it for DICE devices, because the old DICE-II chip will in some cases
not be able to lock to non-blocking streams (erratum E7).
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Instead of forcing a constant 44.1 kHz, read the current sample rate
from the device when opening the PCM device.
Actually changing the sample rate requires some separate controller
application.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
After a bus reset, do not stop the stream completely to avoid having to
reconfigure the device when restarting the stream.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
This patch adds support for device tree for the CS42L73 CODEC
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
When there is an external clock, always use this one.
This prevents the two Dove audio devices to use the same DCO clock
at different rates.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mark Brown <broonie@linaro.org>
R-Car sound has clock pin for each SSI, and sometimes,
these pins are shared with paired SSI.
It may sometimes become "SSI-A clock pin is master" and
"SSI-B clock pin is slave", but "SSI-A/B clock pins are shared".
SSI-B needs SSI-A clock in this case.
Current R-Car sound driver is using RSND_SSI_xxx flag
to control this kind of shared pin behavior.
But, this information, especially clock master setting,
can be got from ASoC set_fmt settings.
This patch removes rsnd_ssi_mode_init() and extend rsnd_ssi_mode_set()
to controlling pin settings via .set_fmt.
This patch doesn't removes RSND_SSI_CLK_FROM_ADG flag at this point
to avoid conflict branch merging between ASoC <-> SH-ARM.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current SSI needs RSND_SSI_DEPENDENT flag to
decide dependent/independent mode.
And SCU needs RSND_SCU_USE_HPBIF flag
to decide HPBIF is enable/disable.
But these 2 means same things.
This patch adds new rsnd_scu_hpbif_is_enable()
function, and merges above methods.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current simple-card returns error if DAI doesn't
support .set_fmt callback.
But the error is -ENOTSUPP (= not supported),
and it is not error.
This patch avoids such case
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Allow DMA data to be set at probe time for devices that can do that,
avoiding the need to do it every time we start a stream and supporting
non-DT dmaengine users using the helpers.
Signed-off-by: Mark Brown <broonie@linaro.org>
Help ensure that Lars-Peter gets CCed on dmaengine related patches by
adding a MAINTAINERS entry for the helpers.
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A number of small, fairly unexciting, fixes for drivers - nothing stand
out.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=aZuy
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.12-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.12
A number of small, fairly unexciting, fixes for drivers - nothing stand
out.
This patch adds some default settings for the generic dmaengine PCM driver for
the case that no config has been supplied. The following defaults are used:
* Use snd_dmaengine_pcm_prepare_slave_config for preparing the DMA slave
config.
* 512kB for the prealloc buffer size. This value has been chosen based on
'feels about right' and is not backed up by any scientific facts. We
may need to come up with something smarter in the future but it should
work fine for now.
With this infrastructure in place we can finally write DAI drivers which are
independent of the DMA controller they are connected to. This is e.g. useful if
the DAI IP core is reused across different SoCs, but the SoCs uses different DMA
controllers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently each platform making use the the generic dmaengine PCM driver still
needs to provide a custom snd_pcm_hardware struct which specifies the
capabilities of the DMA controller, e.g. the maximum period size that can be
supported. This patch adds code which uses the newly introduced
dma_get_slave_caps() API to query this information from the dmaengine driver.
The new code path will only be taken if the 'pcm_hardware' field of the
snd_dmaengine_pcm_config struct is NULL.
The patch also introduces a new 'fifo_size' field to the
snd_dmaengine_dai_dma_data struct which is used to initialize the
snd_pcm_hardware 'fifo_size' field and needs to be set by the DAI driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is no need for the CODEC to go to standby on resume since the core will
power it up as needed and in any case it is an idle_bias_off CODEC so would
normally sit with bias off while idle.
Signed-off-by: Mark Brown <broonie@linaro.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
If we have control over the LDO then disable it during suspend; the device
is already being put into reset so will be non-functional over suspend
anyway and this will save a small amount of power.
Signed-off-by: Mark Brown <broonie@linaro.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
The core support for ep93xx (currently only the DMA driver) does not
depend on the architecture at all and everything else has more strict
dependencies so enable compile test builds for improved build coverage.
Signed-off-by: Mark Brown <broonie@linaro.org>
Jyri Sarha