When the firmware security is enabled, the pcie_aux_dbi_reg_addr
register in the PCI controller is blocked. Therefore, ignore
the result of writing to this register and assume it worked. Also
remove the prints on errors in the internal ELBI write function.
If the security is enabled, the firmware is responsible for setting
this register correctly so we won't have any problem.
If the security is disabled, the write will work (unless something
is totally broken at the PCI level and then the whole sequence
will fail).
In addition, remove a write to register pcie_aux_dbi_reg_addr+4,
which was never actually needed.
Moreover, PCIE_DBI registers are blocked to access from host when
firmware security is enabled. Use a different register to flush the
writes.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In case the clock gating was enabled in preboot we need to disable it
at the H/W initialization stage before touching the MME/TPC registers.
Otherwise, the ASIC can get stuck. If the security is enabled in
the firmware level, the CGM is always disabled and the driver can't
enable it.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
We don't need to set EB on signal packets from collective slave
queues as it degrades performance. Because the slaves are the network
queues, the engine barrier doesn't actually guarantee that the
packet has been sent.
Signed-off-by: Alon Mizrahi <amizrahi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
FW hard reset capability indication is now moved to preboot stage.
Driver will check if HW is dirty only after it validated preboot
is up. If HW is dirty, driver will perform a hard reset according
to the FW capability.
In addition, FW defines a new message which driver need to send in
order to initiate a hard reset.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
As we only fetch the CPU_PLL frequency in gaudi, we don't need a
generic get_pll_frequency function which takes a pll index as input
Signed-off-by: Alon Mizrahi <amizrahi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Modify the CS counter of a CB to be atomic, so no locking is required
when it is being modified or read.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Some messages should be changed to debug mode as we want to keep
minimal prints during normal operation of the device.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Currently, if the f/w is in preboot/u-boot they don't perform the new
reset mechanism. Therefore, the driver needs to reset the device.
To prevent reset of PCI_IF, the driver needs to first configure the
reset units.
If the security is enabled, the driver can't configure the reset units.
In that situation, don't reset the card.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
We have the ECC type field from the firmware but the driver didn't
print it, so we need to add that field to the ECC print message.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Make a function in gaudi.c to be static
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: kernel test robot <lkp@intel.com>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Once firmware security is enabled, driver must fetch pll frequencies
through the firmware message interface instead of reading the registers
directly.
Signed-off-by: Alon Mizrahi <amizrahi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
We introduce a new wrapper which allows us to mmu map any size
to any host va_range available. In addition we remove duplicated
code from various places in driver and using this new wrapper
instead.
This wrapper supports mapping only contiguous physical
memory blocks and will be used for mappings that are done to the
driver ASID.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
As part of the security effort in which FW will be handling
sensitive HW registers, hard reset flow will be done by FW
and will be triggered by driver.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
F/W message returns 64bit value but up until now we casted it to
a 32bit variable, instead of receiving 64bit in the first place.
Signed-off-by: Alon Mizrahi <amizrahi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Add support for reserving va block with alignment different than
page size. This is a pre-requisite for allocations needed in future
ASICs
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Once FW security is enabled there is no access to HBM ecc registers,
need to read values from FW using a dedicated interface.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Driver must fetch FW hard reset capability during boot time,
in order to skip the hard reset flow if necessary.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Whether an ASIC has MMU towards its DRAM is an ASIC property, so
move it to the asic fixed properties structure.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Instead of using a dedicated va range for each internal pool,
we introduce a new way for reserving a va block from an existing
va range. This is a more generic way of reserving va blocks for
future use.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Driver must verify if HW is dirty before trying to fetch preboot
information. Hence, we move this validation to a prior stage of
the boot sequence.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The new state indicates that device should be reset in order
to re-gain funcionality.
This unique state can occur if reset_on_lockup is disabled
and an actual lockup has occurred.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Since the very large grace period is over and this functionality
prevents us to implement the new reset sequence and apply security
settings, we need to remove the code toggling the PCIE_EN bit in the
straps register.
Remove it for good.
Signed-off-by: Igor Grinberg <igrinberg@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
We print twice the firmware status regarding security, once in
common code and once in asic code. Remove the print in asic code
and leave the common code print.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
We need to have the MAX CS be much larger than the size of the
different queues. In GAUDI we have around 8 groups of queues, and each
group has 1K queue size. To prevent head-of-the-line blocking, we need
to make sure there is sufficient number of available CS allocations
even if one or more of those queues are full.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
failure in reading pre-boot verion is not handled correctly,
upon failure we need to reset the device in order to be able
to reinstall the driver.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Several header files are repeatedly included in many files.
Move these files to habanalabs.h which is included by all.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Once FW security is enabled there is no access to PLL registers,
need to read values from FW using a dedicated interface.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In cases of multi-tenants, administrators may want to prevent data
leakage between users running on the same device one after another.
To do that the driver can scrub the internal memory (both SRAM and
DRAM) after a user finish to use the memory.
Because in GAUDI the driver allows only one application to use the
device at a time, it can scrub the memory when user app close FD.
In future devices where we have MMU on the DRAM, we can scrub the DRAM
memory with a finer granularity (page granularity) when the user
allocates the memory.
This feature is not supported in Goya.
To allow users that want to debug their applications, we add a kernel
module parameter to load the driver with this feature disabled.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Skip relevant HW configurations once FW security is enabled
because these configurations are being performed by FW.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Add support for fetching security indication from FW.
This indication is needed in order to skip unnecessary
initializations done by FW.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Fix cs counters structure in uapi to be one flat structure instead
of two instances of the same other structure.
use atomic read/increment for context counters so we could use
one structure for both aggregated and context counters.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Today driver is able to load a whole FW binary into a specific
location on ASIC. We add support for loading sections from the
same FW binary into different loactions.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Implement sync stream collective for GAUDI. Need to allocate additional
resources for that and add ctx_fini() to clean up those resources.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
DMA5 QMAN is designated to be used for reduction process, hence it will
be no longer configured as external queue.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Define new API for collective wait support and modify sync stream
common flow. In addition add kernel CB allocation support for
internal queues.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In the future there will be situations where queues can accept either
kernel allocated CBs or user allocated CBs, depending on different
states.
Therefore, instead of using a boolean variable of kernel/user allocated
CB, we need to use a bitmask to indicate that, which will allow to
combine the two options.
Add a flag to the uapi so the user will be able to indicate whether
the CB was allocated by kernel or by user. Of course the driver
validates that.
Signed-off-by: Tal Cohen <talcohen@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Initialize the QMANs that are responsible to submit doorbells to the NIC
engines. Add support for stopping and disabling them, and reset them as
part of the hard-reset procedure of GAUDI. This will allow the user to
submit work to the NICs.
Add support for receiving events on QMAN errors from the firmware.
However, the nic_ports_mask is still initialized to 0. That means this code
won't initialize the QMANs just yet. That will be in a later patch.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Configure the security properties of the NIC IP. This is to prevent the
user process from doing something with the NIC that he shouldn't do. e.g.
crash the server, steal data, etc.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Support advanced monitor functionality to monitor more than a
single SOB. In addition expand all CB generation functions
with buffer offset in order to put in them multiple packets that are
generated by different functions.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
No need to print when the driver starts to initialize the H/W. Drivers
should be silent when everything is OK.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Currently mmu_prepare is located at context switch.
Since we support a single context, no reason to reconfigure
the MMU registers every context switch.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
There is missing statement and missing "break;" in the ECC handling
code in gaudi.c
This will cause a wrong behavior upon certain ECC interrupts.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
We must relocate the coresight mmu configuration to the coresight
flow to make it work in case the first submission is to configure
the profiler.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
All throughout the driver, normal kernel pointers are
stored as 'u64' struct members, which is kind of silly
and requires casting through a uintptr_t to void* every
time they are used.
There is one line that missed the intermediate uintptr_t
case, which leads to a compiler warning:
drivers/misc/habanalabs/common/command_buffer.c: In function 'hl_cb_mmap':
drivers/misc/habanalabs/common/command_buffer.c:512:44: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
512 | rc = hdev->asic_funcs->cb_mmap(hdev, vma, (void *) cb->kernel_address,
Rather than adding one more cast, just fix the type and
remove all the other casts.
Fixes: 0db575350c ("habanalabs: make use of dma_mmap_coherent")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
LDMA registers are configured with a fixed value.
We add new define set which gives the configuration
a proper meaning.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Future F/W versions will have enhanced security measures and the driver
won't be able to do certain configurations that it always did and those
configurations will be done by the firmware.
We use the firmware's preboot version to determine whether security
measures are enabled or not. Because we need this very early in our code,
the read of the preboot version is moved to the earliest possible place,
right after the device's PCI initialization.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
This is a workaround for H/W bug H3-2116, where if there are more than 16
outstanding completions in the DMA transpose engine, there can be a
deadlock in the engine.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
There are cases in which the device should access the host memory of a
CB through the device MMU, and thus this memory should be mapped.
The patch adds a flag to the CB IOCTL, in which a user can ask the
driver to perform the mapping when creating a CB.
The mapping is allowed only if a dedicated VA range was allocated for
the specific ASIC.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Future changes require using a context while handling a command buffer,
and thus need to save the context in the command buffer object.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
The firmware running in the boot stage takes more time to execute due to
increased security mechanisms. Therefore, we need to increase the timeout
we wait for the boot fit to finish loading.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
This commit adds the number of HOPs supported by the device to the
device MMU properties.
Signed-off-by: Moti Haimovski <mhaimovski@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
There were a couple of comments where the name ArmCP was still used. Rename
it to CPU-CP.
In addition, rename ArmCP or ARM in log messages to "device CPU".
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Add dma_mmap_coherent() for goya and gaudi to match their use of
dma_alloc_coherent(), see the Link tag for why.
Link: https://lore.kernel.org/lkml/20200609091727.GA23814@lst.de/
Cc: Christoph Hellwig <hch@lst.de>
Cc: Zhang Li <li.zhang@bitmain.com>
Cc: Ding Z Nan <oshack@hotmail.com>
Signed-off-by: Hillf Danton <hdanton@sina.com>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
When shifting a boolean variable by more than 31 bits and putting the
result into a u64 variable, we need to cast the boolean into unsigned 64
bits to prevent possible overflow.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
ArmCP mandates that the device CPU is always an ARM processor, which might
be wrong in the future.
Most of this change is an internal renaming of variables, functions and
defines but there are two entries in sysfs which have armcp in their
names. Add identical cpucp entries but don't remove yet the armcp entries.
Those will be deprecated next year. Add the documentation about it in sysfs
documentation.
Signed-off-by: Moti Haimovski <mhaimovski@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Include linux/bitfield.h only in habanalabs.h, instead of in each and
every file that needs it, as habanalabs.h is already included by all.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
change busy engines bitmask to 64 bits in order to represent
more engines, needed for future ASIC support.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Eliminate following warning:
warning: Shifting signed 32-bit value by 31 bits is undefined behavior
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
The driver waits for the TPC vector pipe to be empty before checking if the
TPC kernel has finished executing, but the code doesn't validate that the
pipe was indeed empty, it just wait for it without checking the return
value.
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
new_dma_pkt->ctl is assigned a value and then is reassigned a new value
without the first value ever being used.
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Use the standard FIELD_PREP() macro instead of << operator to perform
bitmask operations. This ensures type check safety and eliminate compiler
warnings.
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Use the standard macros to define bitmasks.
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
If there is a failure during the testing of a queue,
to ease up debugging - print the queue id.
Signed-off-by: Dotan Barak <dbarak@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Allow user application to write to this register in order
to be able to configure the quiet period of the QMAN between grants.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Although the driver defines the first user-available sync manager object
and monitor in habanalabs.h, we would like to also expose this information
via the INFO IOCTL so the runtime can get this information dynamically.
This is because in future ASICs we won't need to define it statically.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Update firmware header with new API for getting pcie info
such as tx/rx throughput and replay counter.
These counters are needed by customers for monitor and maintenance
of multiple devices.
Add new opcodes to the INFO ioctl to retrieve these counters.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
In Gaudi, the default max power setting is different between PCI and PMC
cards. Therefore, the driver need to set the default after knowing what is
the card type.
The current code has a bug where it limits the maximum power of the PMC
card to 200W after a reset occurs.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Allocation size can go up to 64bit but truncated to 32bit,
we should make sure it is not truncated and validate no address
overflow.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Once clock gating is set we enable clock gating according to mask,
we should also disable clock gating according to relevant bits.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
The condition was reversed. It should have been less than instead of
greater than. The result is that we never enter the loop.
Fixes: fcc6a4e606 ("habanalabs: Extract ECC information from FW")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
During command buffer parsing, driver extracts packet id
from user buffer. Driver must validate this packet id, since it is
being used in order to extract information from internal structures.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
There's no need to try to be cute with the include file locations in the
Makefile, so just specify exactly where the files are.
Bonus is this fixes the problem of building with O= as well as trying to
just build the subdirectory alone.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Oded Gabbay <oded.gabbay@gmail.com>
Cc: Omer Shpigelman <oshpigelman@habana.ai>
Cc: Tomer Tayar <ttayar@habana.ai>
Cc: Moti Haimovski <mhaimovski@habana.ai>
Cc: Ofir Bitton <obitton@habana.ai>
Cc: Ben Segal <bpsegal20@gmail.com>
Cc: Christine Gharzuzi <cgharzuzi@habana.ai>
Cc: Pawel Piskorski <ppiskorski@habana.ai>
Link: https://lore.kernel.org/r/20200728171851.55842-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gaudi_mmu_invalidate_cache() doesn't use the flags parameter, and thus
it can be set to 0 when the function is called in the gaudi only files.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Create a device MMU-mapped internal command buffer pool, in order to allow
the driver to allocate CBs for the signal/wait operations
that are fetched by the queues when they are configured with the user's
address space ID.
We must pre-map this internal pool due to performance issues.
This pool is needed for future ASIC support and it is currently unused in
GOYA and GAUDI.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
For internal needs of our CI we need to move all the common code into a
common folder instead of putting them in the root folder of the driver.
Same applies to the common header files under include/
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Reviewed-by: Omer Shpigelman <oshpigelman@habana.ai>
In GAUDI we use QMAN0 DMA for clearing the MMU memory region
at initialization. if this operation fails it places the DMA in an error
state and then when trying to initialize QMAN0 we fail and erroneously
assume its the QMAN that failed.
This commit adds a check and clear of such DMA errors at initialization so
we will have a better understanding of what went wrong.
Signed-off-by: Moti Haimovski <mhaimovski@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Currently the driver halts the device CPU in the halt engines function,
which halts all the engines of the ASIC. The problem is that if later on we
stop the reset process (due to inability to clean memory mappings in time),
the CPU will remain in halt mode. This creates many issues, such as
thermal/power control and FLR handling.
Therefore, move the halting of the device CPU to the very end of the reset
process, just before writing to the registers to initiate the reset. In
addition, the driver now needs to send a message to the device F/W to
disable it from sending interrupts to the host machine because during halt
engines function the driver disables the MSI/MSI-X interrupts.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
Currently the amount of maximum queues is statically configured.
Using a static value is causing redundunt cycles when traversing
all queues and consumes more memory than actually needed.
In this patch we configure each asic with the exact number of
queues needed.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Soft-reset isn't supported in GAUDI. Remove the code that performs it and
print error in case the user wants to do it via sysfs.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
Divide iATU initialization into inbound/outbound methods.
We must separate it in order to enable different match mode
per PCIe region.
In addition, added support for PCI address match mode.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
ECC (Error Correcting Code) interrupts are going to be handled
by the FW. Hence, we define an interface in which the driver can
obtain the relevant ECC information.
This information is needed for monitoring and can also lead
to a hard reset if ECC error is not correctable.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
After recent concurrent cs amount increase, we must also
increase queues depth since much more concurrent work can be done.
All external queue depths were increased to 4096 as gaudi's
internal queue depths were also increased to 1024.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
The profiler needs to know the PLL values for correctly showing the
profiling data. Because our firmware can use different PLL configurations,
we need to read the PLL values from the ASIC to pass them to the profiler.
Signed-off-by: Adam Aharon <aaharon@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Currently sync stream is limited only for external queues. We want to
remove this constraint by adding a new queue property dedicated for sync
stream. In addition we move the initialization and reset methods to the
common code since we can re-use them with slight changes.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Training schemes requires much more concurrent command submissions than
inference does. In addition, training command submissions can be completed
in a non serialized manner. Hence, we add support in which each ASIC will
be able to configure the amount of concurrent pending command submissions,
rather than use a predefined amount. This change will enhance performance
by allowing the user to add more concurrent work without waiting for the
previous work to be completed.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
We no longer need to initialize the rate limiters in GAUDI A1.
Reviewed-by: Omer Shpigelman <oshpigelman@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
We see that sometimes the CPU in GOYA and GAUDI is occupied by the
power/thermal loop and can't answer requests from the driver fast enough.
Therefore, to avoid false notifications on timeouts, increase the timeout
to 4 seconds on each message sent to the device CPU.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
For debugging purposes, we need to allow the root user better control of
the clock gating feature of the DMA and compute engines. Therefore, change
the clock gating debugfs interface to be bitmask instead of true/false.
Each bit represents a different engine, according to gaudi_engine_id enum.
See debugfs documentation for more details.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Reviewed-by: Omer Shpigelman <oshpigelman@habana.ai>
WREG_BULK is a special packet that has a variable length. Therefore, we
can't parse it when validating CBs that go to the PCI DMA queue. In case
the user needs to use it, it can put multiple WREG32 packets instead.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Reviewed-by: Omer Shpigelman <oshpigelman@habana.ai>
gaudi_pb_set_block()'s argument 'base' was incorrectly named 'block' in
its function header.
Fixes the following W=1 kernel build warning(s):
drivers/misc/habanalabs/gaudi/gaudi_security.c:454: warning: Function parameter or member 'base' not described in 'gaudi_pb_set_block'
drivers/misc/habanalabs/gaudi/gaudi_security.c:454: warning: Excess function parameter 'block' description in 'gaudi_pb_set_block'
Cc: Oded Gabbay <oded.gabbay@gmail.com>
Cc: Tomer Tayar <ttayar@habana.ai>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Link: https://lore.kernel.org/r/20200701085853.164358-11-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
W=1 kernel builds report a lack of description of gaudi_set_asic_funcs()'s
'hdev' argument. In reality it is documented, but the formatting
was not as expected '@.*:'. Instead, there was a misplaced asterisk
which was confusing the kerneldoc validator.
Squashes the following W=1 warning:
drivers/misc/habanalabs/gaudi/gaudi.c:6746: warning: Function parameter or member 'hdev' not described in 'gaudi_set_asic_funcs'
Cc: Oded Gabbay <oded.gabbay@gmail.com>
Cc: Tomer Tayar <ttayar@habana.ai>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Link: https://lore.kernel.org/r/20200701085853.164358-10-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In GAUDI the current timer value for the hardware to check if it is
in IDLE state is too low. As a result, there are occasions where the H/W
wrongly reports it is not IDLE. The driver checks that before submitting
work on behalf of the driver during initialization, so a false report might
cause the driver to fail during device initialization.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
The current timeout is too low for some of the workloads and we see false
errors as a result.
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
The PS flow for MMU cache invalidation caused timeouts in stress tests.
Use PS + PI flow so no timeouts should happen whatsoever.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
In Gaudi, the user can't execute scalar load_and_exe on external queue
because it can be a security hole. The driver doesn't parse the commands
being loaded and it can be msg_prot, which the user isn't allowed to use.
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
MMU cache invalidation timeout indicates that the device is unstable and
therefore unusable.
Hence in such case do hard reset and return an error to the user if was
called from ioctl.
In addition, change the print to error level and rephrase its text.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
GAUDI does not support soft-reset as it leaves the NIC ports in an awkward
state, where their QMANs were reset but the NIC itself is still working.
In addition, there is not much sense in doing soft-reset when training is
done on multiple GAUDIs.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
A new sequence is introduced to invalidate the MMU cache in order to avoid
timeouts.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Instead of writing similar event handling code for each ASIC, move the code
to the common firmware file. This code will be used for GAUDI and all
future ASICs.
In addition, add two new fields to the auto-generated events file: valid
and description. This will save the need to manually write the events
description in the source code and simplify the code.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Add the GAUDI code to initialize the ASIC's profiler. The profile receives
its initialization values from the user, same as in Goya, but the code to
initialize is in the driver because the configuration space of the
device is not directly exposed to the user.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Add the code to initialize the security module of GAUDI. Similar to Goya,
we have two dedicated mechanisms for security: Range Registers and
Protection bits. Those mechanisms protect sensitive memory and
configuration areas inside the device.
In addition, in Gaudi we moved to a 3-level security scheme, where the F/W
runs with the highest security level (Privileged), the driver runs with a
less secured level (Secured) and the user is neither privileged nor
secured. The security module in the driver configures the Secured parts so
the user won't be able to access them. The Privileged parts are configured
by the F/W.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
The hwmgr module is responsible for messages sent to GAUDI F/W that are
not common to all habanalabs ASICs.
In GAUDI, we provide the user a simplified mode of controlling the ASIC
clock frequency. Instead of three different clocks, we present a single
clock property that the user can configure via sysfs.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Add the ASIC-dependent code for GAUDI. Supply (almost) all of the function
callbacks that the driver's common code need to initialize, finalize and
submit workloads to the GAUDI ASIC.
It also contains the code to initialize the F/W of the GAUDI ASIC and to
receive events from the F/W.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Oded Gabbay