take care of UpDbgLaRdPtr[0-3] restriction for T6.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Take uld mutex to avoid race between cxgb_up() and
cxgb4_register_uld() to enable napi for the same uld
queue.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change t4fw_version.h to update latest firmware version
number to 1.16.45.0.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GRO is not supported by Chelsio HW when rx_csum is disabled.
Update the netdev features flag when rx_csum is modified.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable FW_OK flag while flashing Firmware. This will help to fix any
potential mailbox timeouts during Firmware flash.
Grab new devlog parameters after Firmware restart. When we FLASH new
Firmware onto an adapter, the new Firmware may have the Firmware Device Log
located at a different memory address or have a different size for it.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark carrier off before registering netdev to ensure that vlan device
picks up the correct state of the carrier
Signed-off-by: Surendra Mobiya <surendra@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During PCI error recovery process, specifically on eeh_err_detected()
we might have a NULL netdev struct, hence a direct dereference will
lead to a kernel oops. This was observed with latest upstream kernel
(v4.12-rc2) on Chelsio adapter T422-CR in PowerPC machines.
This patch checks for NULL pointer and avoids the crash, both in
eeh_err_detected() and eeh_resume(). Also, we avoid to trigger
a fatal error or to try disabling interrupts on FW during PCI
error recovery, because: (a) driver might not be able to accurately
access PCI regions in this case, and (b) trigger a fatal error
_during_ the recovery steps is a mistake that could prevent the
recovery path to complete successfully.
Reported-by: Harsha Thyagaraja <hathyaga@in.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
issue get port information command to firmware to retrieve port
information and update if it is different from what was last
recorded and also add indication for supported link modes for
firmware port types FW_PORT_TYPE_SFP28, FW_PORT_TYPE_KR_SFP28,
FW_PORT_TYPE_CR4_QSFP.
Based on the original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change t4fw_version.h to update latest firmware version
number to 1.16.43.0.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When is_kdump_kernel() is true, reduce memory footprint of
cxgb4 by using a single "Queue Set".
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix multiqueue in stmmac driver on PCI, from Andy Shevchenko.
2) cdc_ncm doesn't actually fully zero out the padding area is
allocates on TX, from Jim Baxter.
3) Don't leak map addresses in BPF verifier, from Daniel Borkmann.
4) If we randomize TCP timestamps, we have to do it everywhere
including SYN cookies. From Eric Dumazet.
5) Fix "ethtool -S" crash in aquantia driver, from Pavel Belous.
6) Fix allocation size for ntp filter bitmap in bnxt_en driver, from
Dan Carpenter.
7) Add missing memory allocation return value check to DSA loop driver,
from Christophe Jaillet.
8) Fix XDP leak on driver unload in qed driver, from Suddarsana Reddy
Kalluru.
9) Don't inherit MC list from parent inet connection sockets, another
syzkaller spotted gem. Fix from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
dccp/tcp: do not inherit mc_list from parent
qede: Split PF/VF ndos.
qed: Correct doorbell configuration for !4Kb pages
qed: Tell QM the number of tasks
qed: Fix VF removal sequence
qede: Fix XDP memory leak on unload
net/mlx4_core: Reduce harmless SRIOV error message to debug level
net/mlx4_en: Avoid adding steering rules with invalid ring
net/mlx4_en: Change the error print to debug print
drivers: net: wimax: i2400m: i2400m-usb: Use time_after for time comparison
DECnet: Use container_of() for embedded struct
Revert "ipv4: restore rt->fi for reference counting"
net: mdio-mux: bcm-iproc: call mdiobus_free() in error path
net: ethernet: ti: cpsw: adjust cpsw fifos depth for fullduplex flow control
ipv6: reorder ip6_route_dev_notifier after ipv6_dev_notf
net: cdc_ncm: Fix TX zero padding
stmmac: pci: split out common_default_data() helper
stmmac: pci: RX queue routing configuration
stmmac: pci: TX and RX queue priority configuration
stmmac: pci: set default number of rx and tx queues
...
There are many code paths opencoding kvmalloc. Let's use the helper
instead. The main difference to kvmalloc is that those users are
usually not considering all the aspects of the memory allocator. E.g.
allocation requests <= 32kB (with 4kB pages) are basically never failing
and invoke OOM killer to satisfy the allocation. This sounds too
disruptive for something that has a reasonable fallback - the vmalloc.
On the other hand those requests might fallback to vmalloc even when the
memory allocator would succeed after several more reclaim/compaction
attempts previously. There is no guarantee something like that happens
though.
This patch converts many of those places to kv[mz]alloc* helpers because
they are more conservative.
Link: http://lkml.kernel.org/r/20170306103327.2766-2-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> # Xen bits
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Andreas Dilger <andreas.dilger@intel.com> # Lustre
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com> # KVM/s390
Acked-by: Dan Williams <dan.j.williams@intel.com> # nvdim
Acked-by: David Sterba <dsterba@suse.com> # btrfs
Acked-by: Ilya Dryomov <idryomov@gmail.com> # Ceph
Acked-by: Tariq Toukan <tariqt@mellanox.com> # mlx4
Acked-by: Leon Romanovsky <leonro@mellanox.com> # mlx5
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Anton Vorontsov <anton@enomsg.org>
Cc: Colin Cross <ccross@android.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Kent Overstreet <kent.overstreet@gmail.com>
Cc: Santosh Raspatur <santosh@chelsio.com>
Cc: Hariprasad S <hariprasad@chelsio.com>
Cc: Yishai Hadas <yishaih@mellanox.com>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: "Yan, Zheng" <zyan@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recent Chelsio firmware started using few port capablity bits to
manage FEC and as driver was not aware of FEC changes those bits
were zeroed, consequently disabling FEC.
Avoid zeroing those bits and default to whatever the firmware
tells us the Link is currently advertising.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Millar:
"Here are some highlights from the 2065 networking commits that
happened this development cycle:
1) XDP support for IXGBE (John Fastabend) and thunderx (Sunil Kowuri)
2) Add a generic XDP driver, so that anyone can test XDP even if they
lack a networking device whose driver has explicit XDP support
(me).
3) Sparc64 now has an eBPF JIT too (me)
4) Add a BPF program testing framework via BPF_PROG_TEST_RUN (Alexei
Starovoitov)
5) Make netfitler network namespace teardown less expensive (Florian
Westphal)
6) Add symmetric hashing support to nft_hash (Laura Garcia Liebana)
7) Implement NAPI and GRO in netvsc driver (Stephen Hemminger)
8) Support TC flower offload statistics in mlxsw (Arkadi Sharshevsky)
9) Multiqueue support in stmmac driver (Joao Pinto)
10) Remove TCP timewait recycling, it never really could possibly work
well in the real world and timestamp randomization really zaps any
hint of usability this feature had (Soheil Hassas Yeganeh)
11) Support level3 vs level4 ECMP route hashing in ipv4 (Nikolay
Aleksandrov)
12) Add socket busy poll support to epoll (Sridhar Samudrala)
13) Netlink extended ACK support (Johannes Berg, Pablo Neira Ayuso,
and several others)
14) IPSEC hw offload infrastructure (Steffen Klassert)"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2065 commits)
tipc: refactor function tipc_sk_recv_stream()
tipc: refactor function tipc_sk_recvmsg()
net: thunderx: Optimize page recycling for XDP
net: thunderx: Support for XDP header adjustment
net: thunderx: Add support for XDP_TX
net: thunderx: Add support for XDP_DROP
net: thunderx: Add basic XDP support
net: thunderx: Cleanup receive buffer allocation
net: thunderx: Optimize CQE_TX handling
net: thunderx: Optimize RBDR descriptor handling
net: thunderx: Support for page recycling
ipx: call ipxitf_put() in ioctl error path
net: sched: add helpers to handle extended actions
qed*: Fix issues in the ptp filter config implementation.
qede: Fix concurrency issue in PTP Tx path processing.
stmmac: Add support for SIMATIC IOT2000 platform
net: hns: fix ethtool_get_strings overflow in hns driver
tcp: fix wraparound issue in tcp_lp
bpf, arm64: fix jit branch offset related to ldimm64
bpf, arm64: implement jiting of BPF_XADD
...
The patch fixes a critical issue to map txqid with flows on the hardware appropriately,
if tx queues created are more than flows configured then txqid shall map within
the range of hardware flows configured. This ensure that un-mapped txqid does not remain un-handled.
The patch also segregated the rxqid and txqid for clarity.
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Reviewed-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Save the filter tid while creating the server filter, which is used
later to retrieve the corresponding filter instance while handling
the filter reply.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using a private copy of struct net_device_stats in
struct port_info, use stats from struct net_device.
Cc: Santosh Raspatur <santosh@chelsio.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using a private copy of struct net_device_stats in struct
port_info, use stats from struct net_device.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are using the smallest padding boundary (8 bytes), which isn't
smaller than the Memory Controller Read/Write Size
We get best performance in 100G when the Packing Boundary is a multiple
of the Maximum Payload Size. Its related to inefficient chopping of DMA
packets by PCIe, that causes more overhead on bus. So driver is helping
by making the starting address alignment to be MPS size.
We will try to determine PCIE MaxPayloadSize capabiltiy and set
IngPackBoundary based on this value. If cache line size is greater than
MPS or determinig MPS fails, we will use cache line size to determine
IngPackBoundary(as before).
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix double-free in batman-adv, from Sven Eckelmann.
2) Fix packet stats for fast-RX path, from Joannes Berg.
3) Netfilter's ip_route_me_harder() doesn't handle request sockets
properly, fix from Florian Westphal.
4) Fix sendmsg deadlock in rxrpc, from David Howells.
5) Add missing RCU locking to transport hashtable scan, from Xin Long.
6) Fix potential packet loss in mlxsw driver, from Ido Schimmel.
7) Fix race in NAPI handling between poll handlers and busy polling,
from Eric Dumazet.
8) TX path in vxlan and geneve need proper RCU locking, from Jakub
Kicinski.
9) SYN processing in DCCP and TCP need to disable BH, from Eric
Dumazet.
10) Properly handle net_enable_timestamp() being invoked from IRQ
context, also from Eric Dumazet.
11) Fix crash on device-tree systems in xgene driver, from Alban Bedel.
12) Do not call sk_free() on a locked socket, from Arnaldo Carvalho de
Melo.
13) Fix use-after-free in netvsc driver, from Dexuan Cui.
14) Fix max MTU setting in bonding driver, from WANG Cong.
15) xen-netback hash table can be allocated from softirq context, so use
GFP_ATOMIC. From Anoob Soman.
16) Fix MAC address change bug in bgmac driver, from Hari Vyas.
17) strparser needs to destroy strp_wq on module exit, from WANG Cong.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (69 commits)
strparser: destroy workqueue on module exit
sfc: fix IPID endianness in TSOv2
sfc: avoid max() in array size
rds: remove unnecessary returned value check
rxrpc: Fix potential NULL-pointer exception
nfp: correct DMA direction in XDP DMA sync
nfp: don't tell FW about the reserved buffer space
net: ethernet: bgmac: mac address change bug
net: ethernet: bgmac: init sequence bug
xen-netback: don't vfree() queues under spinlock
xen-netback: keep a local pointer for vif in backend_disconnect()
netfilter: nf_tables: don't call nfnetlink_set_err() if nfnetlink_send() fails
netfilter: nft_set_rbtree: incorrect assumption on lower interval lookups
netfilter: nf_conntrack_sip: fix wrong memory initialisation
can: flexcan: fix typo in comment
can: usb_8dev: Fix memory leak of priv->cmd_msg_buffer
can: gs_usb: fix coding style
can: gs_usb: Don't use stack memory for USB transfers
ixgbe: Limit use of 2K buffers on architectures with 256B or larger cache lines
ixgbe: update the rss key on h/w, when ethtool ask for it
...
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- enable dual mode (initiator + target) qla2xxx operation. (Quinn +
Himanshu)
- add a framework for qla2xxx async fabric discovery. (Quinn +
Himanshu)
- enable iscsi PDU DDP completion offload in cxgbit/T6 NICs. (Varun)
- fix target-core handling of aborted failed commands. (Bart)
- fix a long standing target-core issue NULL pointer dereference with
active I/O LUN shutdown. (Rob Millner + Bryant + nab)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (44 commits)
target: Add counters for ABORT_TASK success + failure
iscsi-target: Fix early login failure statistics misses
target: Fix NULL dereference during LUN lookup + active I/O shutdown
target: Delete tmr from list before processing
target: Fix handling of aborted failed commands
uapi: fix linux/target_core_user.h userspace compilation errors
target: export protocol identifier
qla2xxx: Fix a warning reported by the "smatch" static checker
target/iscsi: Fix unsolicited data seq_end_offset calculation
target/cxgbit: add T6 iSCSI DDP completion feature
target/cxgbit: Enable DDP for T6 only if data sequence and pdu are in order
target/cxgbit: Use T6 specific macros to get ETH/IP hdr len
target/cxgbit: use cxgb4_tp_smt_idx() to get smt idx
target/iscsi: split iscsit_check_dataout_hdr()
target: Remove command flag CMD_T_DEV_ACTIVE
target: Remove command flag CMD_T_BUSY
target: Move session check from target_put_sess_cmd() into target_release_cmd_kref()
target: Inline transport_cmd_check_stop()
target: Remove an overly chatty debug message
target: Stop execution if CMD_T_STOP has been set
...
Change t4fw_version.h to update latest firmware version
number to 1.16.33.0.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix typos and add the following to the scripts/spelling.txt:
omited||omitted
omiting||omitting
Link: http://lkml.kernel.org/r/1481573103-11329-26-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove variable rxq_info and also remove redundant assignment
to it.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make max number of supported tc u32 links equal to max number of filters
supported by hardware.
Signed-off-by: Arjun V <arjun@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Count buffer group drops or truncates as rx drops rather than
rx errors in netdev stats.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: Arjun V <arjun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For T6 adapters use T6 specific macro to set the force bit.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch does not change any functionality but avoids that sparse
complains about endianness.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch makes use of is_vlan_dev() function instead of flag
comparison which is exactly done by is_vlan_dev() helper function.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Jon Maxwell <jmaxwell37@gmail.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Acked-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In linux-4.5, busy polling was implemented in core
NAPI stack, meaning that all custom implementation can
be removed from drivers.
Not only we remove lot of code, we also remove one spin_lock()
from driver fast path.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without any uld being loaded, uld_txq_info[] will be NULL. uld_send()
is also used for sending control work requests(for eg: setting filter)
that dont require any ulds to be loaded. Hence move uld_txq_info[]
assignment after ctrl_xmit().
Also added a NULL check for uld_txq_info[].
Fixes: 94cdb8bb99 (cxgb4: Add support for dynamic allocation
of resources for ULD).
Signed-off-by: Arjun V <arjun@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change assign flowc id to each outgoing request.Firmware use flowc id
to schedule each request onto HW. FW reply may miss without this change.
Reviewed-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Change t4fw_version.h to update latest firmware version
number 1.16.26.0.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d30396
("net: gro: add a per device gro flush timer")
This allows for more efficient GRO aggregation without
sacrifying latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The two new variables are only used inside of an #ifdef and cause
harmless warnings when that is disabled:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c: In function 'init_one':
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:4646:9: error: unused variable 'port_vec' [-Werror=unused-variable]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:4646:6: error: unused variable 'v' [-Werror=unused-variable]
This adds another #ifdef around the declarations.
Fixes: 96fe11f27b ("cxgb4: Implement ndo_get_phys_port_id for mgmt dev")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Perform an emergency shutdown of the adapter and stop it from
continuing any further communication on the ports or DMA to the
host. This is typically used when the adapter and/or firmware
have crashed and we want to prevent any further accidental
communication with the rest of the world. This will also force
the port Link Status to go down -- if register writes work --
which should help our peers figure out that we're down.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The region set by the call to memset, immediately overwritten by
the subsequent call to memcpy and thus makes the memset redundant.
Also remove the memset((&info, 0, sizeof(info)) on line 398 because
info is memcpy()'ed to before being used in the loop and it isn't
used outside of the loop.
Signed-off-by: Shyam Saini <mayhs11saini@gmail.com>
Reviewed-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not count pause frames as part of general TX/RX frame
counters.
Based on the original work of Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize mbox lock and list for mgmt dev to avoid NULL pointer
dereference when cxgb_set_vf_mac is called.
And also allocate memory for private data while allocating mgmt
netdev.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.
Fix all drivers with ndo_get_stats64 to have a void function.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add port description for 25G and 100G cards, and also
change few port descriptions in compliance with the new
naming convention.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to report 25G and 100G links, which was missed
as part of commit "eb97ad99f9ed".
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The issue comes when there are multiple threads attempting to use
the mailbox facility at the same time.
When DCB operations and interface up/down is run in a loop for every
0.1 sec, we observed mailbox collisions. And out of the two commands
one would fail with the present code, since we don't queue the second
command.
To overcome the above issue, added a queue to access the mailbox.
Whenever a mailbox command is issued add it to the queue. If its at
the head issue the mailbox command, else wait for the existing command
to complete. Usually command takes less than a milli-second to
complete.
Also timeout from the loop, if the command under execution takes
long time to run.
In reality, the number of mailbox access collisions is going to be
very rare since no one runs such abusive script.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
t6fw-1.15.15.0 enabled compressed error vector in cpl_rx_pkt for T6.
Updating driver to take care of these changes.
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Arjun V <arjun@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_route_output() never returns NULL so
check dst->error instead of !dst.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is mostly stuff which missed the initial pull. There's a new
driver: qedi, some ufs, ibmvscsis and ncr5380 updates plus some
assorted driver fixes and also a fix for the bug where if a device
goes into a blocked state between configuration and sysfs device add
(which can be a long time under async probing) it would become
permanently blocked.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Zofc
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull late SCSI updates from James Bottomley:
"This is mostly stuff which missed the initial pull.
There's a new driver: qedi, and some ufs, ibmvscsis and ncr5380
updates plus some assorted driver fixes and also a fix for the bug
where if a device goes into a blocked state between configuration and
sysfs device add (which can be a long time under async probing) it
would become permanently blocked"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (30 commits)
scsi: avoid a permanent stop of the scsi device's request queue
scsi: mpt3sas: Recognize and act on iopriority info
scsi: qla2xxx: Fix Target mode handling with Multiqueue changes.
scsi: qla2xxx: Add Block Multi Queue functionality.
scsi: qla2xxx: Add multiple queue pair functionality.
scsi: qla2xxx: Utilize pci_alloc_irq_vectors/pci_free_irq_vectors calls.
scsi: qla2xxx: Only allow operational MBX to proceed during RESET.
scsi: hpsa: remove memory allocate failure message
scsi: Update 3ware driver email addresses
scsi: zfcp: fix rport unblock race with LUN recovery
scsi: zfcp: do not trace pure benign residual HBA responses at default level
scsi: zfcp: fix use-after-"free" in FC ingress path after TMF
scsi: libcxgbi: return error if interface is not up
scsi: cxgb4i: libcxgbi: add missing module_put()
scsi: cxgb4i: libcxgbi: cxgb4: add T6 iSCSI completion feature
scsi: cxgb4i: libcxgbi: add active open cmd for T6 adapters
scsi: cxgb4i: use cxgb4_tp_smt_idx() to get smt_idx
scsi: qedi: Add QLogic FastLinQ offload iSCSI driver framework.
scsi: aacraid: remove wildcard for series 9 controllers
scsi: ibmvscsi: add write memory barrier to CRQ processing
...
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
T6 adapters reduce number of completions to host by generating single
completion for all the directly placed(DDP) iSCSI pdus in a sequence.
This patch adds new structure for completion hw cmd (struct
cpl_rx_iscsi_cmp) and implements T6 completion feature.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added missing dev_port assignment in cxgb4vf driver.
Also made dev_port assignment of cxgb4 in sync with cxgb4vf driver.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Arjun V <arjun@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove deprecated module parameters num_vf, dflt_msg_enable and
force_init.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Couple conflicts resolved here:
1) In the MACB driver, a bug fix to properly initialize the
RX tail pointer properly overlapped with some changes
to support variable sized rings.
2) In XGBE we had a "CONFIG_PM" --> "CONFIG_PM_SLEEP" fix
overlapping with a reorganization of the driver to support
ACPI, OF, as well as PCI variants of the chip.
3) In 'net' we had several probe error path bug fixes to the
stmmac driver, meanwhile a lot of this code was cleaned up
and reorganized in 'net-next'.
4) The cls_flower classifier obtained a helper function in
'net-next' called __fl_delete() and this overlapped with
Daniel Borkamann's bug fix to use RCU for object destruction
in 'net'. It also overlapped with Jiri's change to guard
the rhashtable_remove_fast() call with a check against
tc_skip_sw().
5) In mlx4, a revert bug fix in 'net' overlapped with some
unrelated changes in 'net-next'.
6) In geneve, a stale header pointer after pskb_expand_head()
bug fix in 'net' overlapped with a large reorganization of
the same code in 'net-next'. Since the 'net-next' code no
longer had the bug in question, there was nothing to do
other than to simply take the 'net-next' hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently if txq_info->uldtxq cannot be allocated then
txq_info->txq is being kfree'd (which is redundant because it
is NULL) instead of txq_info. Fix this by instead kfree'ing
txq_info.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate resources dynamically for Upper layer driver's (ULD) like
cxgbit, iw_cxgb4, cxgb4i and chcr. The resources allocated include Tx
queues which are allocated when ULD register with cxgb4 driver and freed
while un-registering. The Tx queues which are shared by ULD shall be
allocated by first registering driver and un-allocated by last
unregistering driver.
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling napi_hash_del() before netif_napi_del() is dangerous
if a synchronize_rcu() is not enforced before NAPI struct freeing.
Lets leave this detail to core networking stack and feel
more comfortable.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Hariprasad S <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to release resources properly in error handling path of
alloc_uld_rxqs(), This patch also removes unwanted arguments
and avoids calling the same function twice.
Fixes: 94cdb8bb99 (cxgb4: Add support for dynamic allocation
of resources for ULD
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Somehow, I missed a healthy number of ethernet drivers in the last pass.
Most of these drivers either were in need of an updated max_mtu to make
jumbo frames possible to enable again. In a few cases, also setting a
different min_mtu to match previous lower bounds. There are also a few
drivers that had no upper bounds checking, so they're getting a brand new
ETH_MAX_MTU that is identical to IP_MAX_MTU, but accessible by includes
all ethernet and ethernet-like drivers all have already.
acenic:
- min_mtu = 0, max_mtu = 9000
amazon/ena:
- min_mtu = 128, max_mtu = adapter->max_mtu
amd/xgbe:
- min_mtu = 0, max_mtu = 9000
sb1250:
- min_mtu = 0, max_mtu = 1518
cxgb3:
- min_mtu = 81, max_mtu = 65535
cxgb4:
- min_mtu = 81, max_mtu = 9600
cxgb4vf:
- min_mtu = 81, max_mtu = 65535
benet:
- min_mtu = 256, max_mtu = 9000
ibmveth:
- min_mtu = 68, max_mtu = 65535
ibmvnic:
- min_mtu = adapter->min_mtu, max_mtu = adapter->max_mtu
- remove now redundant ibmvnic_change_mtu
jme:
- min_mtu = 1280, max_mtu = 9202
mv643xx_eth:
- min_mtu = 64, max_mtu = 9500
mlxsw:
- min_mtu = 0, max_mtu = 65535
- Basically bypassing the core checks, and instead relying on dynamic
checks in the respective switch drivers' ndo_change_mtu functions
ns83820:
- min_mtu = 0
- remove redundant ns83820_change_mtu, only checked for mtu > 1500
netxen:
- min_mtu = 0, max_mtu = 8000 (P2), max_mtu = 9600 (P3)
qlge:
- min_mtu = 1500, max_mtu = 9000
- driver only supports setting mtu to 1500 or 9000, so the core check only
rules out < 1500 and > 9000, qlge_change_mtu still needs to check that
the value is 1500 or 9000
qualcomm/emac:
- min_mtu = 46, max_mtu = 9194
xilinx_axienet:
- min_mtu = 64, max_mtu = 9000
Fixes: 61e84623ac ("net: centralize net_device min/max MTU checking")
CC: netdev@vger.kernel.org
CC: Jes Sorensen <jes@trained-monkey.org>
CC: Netanel Belgazal <netanel@annapurnalabs.com>
CC: Tom Lendacky <thomas.lendacky@amd.com>
CC: Santosh Raspatur <santosh@chelsio.com>
CC: Hariprasad S <hariprasad@chelsio.com>
CC: Sathya Perla <sathya.perla@broadcom.com>
CC: Ajit Khaparde <ajit.khaparde@broadcom.com>
CC: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
CC: Somnath Kotur <somnath.kotur@broadcom.com>
CC: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
CC: John Allen <jallen@linux.vnet.ibm.com>
CC: Guo-Fu Tseng <cooldavid@cooldavid.org>
CC: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
CC: Jiri Pirko <jiri@mellanox.com>
CC: Ido Schimmel <idosch@mellanox.com>
CC: Manish Chopra <manish.chopra@qlogic.com>
CC: Sony Chacko <sony.chacko@qlogic.com>
CC: Rajesh Borundia <rajesh.borundia@qlogic.com>
CC: Timur Tabi <timur@codeaurora.org>
CC: Anirudha Sarangi <anirudh@xilinx.com>
CC: John Linn <John.Linn@xilinx.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not let number of offload queue sets to go more than
MAX_OFLD_QSETS, which would otherwise crash the driver
on machines with cores more than MAX_OFLD_QSETS.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A memory leak of qe occurs when t4_sched_queue_unbind fails,
so fix this by free'ing qe on the error exit path.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These accessors are used in various drivers that support tc offloading,
to detect properties of a given 'tc_action'.
'is_tcf_mirred_redirect' tests that the action is TCA_EGRESS_REDIR.
'is_tcf_mirred_mirror' tests that the action is TCA_EGRESS_MIRROR.
As a prep towards supporting INGRESS redir/mirror, rename these
predicates to reflect their true meaning:
s/is_tcf_mirred_redirect/is_tcf_mirred_egress_redirect/
s/is_tcf_mirred_mirror/is_tcf_mirred_egress_mirror/
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Cc: Hariprasad S <hariprasad@chelsio.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Ido Schimmel <idosch@mellanox.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Updates to mlx5
- Updates to mlx4 (two conflicts, both minor and easily resolved)
- Updates to iw_cxgb4 (one conflict, not so obvious to resolve, proper
resolution is to keep the code in cxgb4_main.c as it is in Linus'
tree as attach_uld was refactored and moved into cxgb4_uld.c)
- Improvements to uAPI (moved vendor specific API elements to uAPI area)
- Add hns-roce driver and hns and hns-roce ACPI reset support
- Conversion of all rdma code away from deprecated
create_singlethread_workqueue
- Security improvement: remove unsafe ib_get_dma_mr (breaks lustre in
staging)
-----BEGIN PGP SIGNATURE-----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=LC+S
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull main rdma updates from Doug Ledford:
"This is the main pull request for the rdma stack this release. The
code has been through 0day and I had it tagged for linux-next testing
for a couple days.
Summary:
- updates to mlx5
- updates to mlx4 (two conflicts, both minor and easily resolved)
- updates to iw_cxgb4 (one conflict, not so obvious to resolve,
proper resolution is to keep the code in cxgb4_main.c as it is in
Linus' tree as attach_uld was refactored and moved into
cxgb4_uld.c)
- improvements to uAPI (moved vendor specific API elements to uAPI
area)
- add hns-roce driver and hns and hns-roce ACPI reset support
- conversion of all rdma code away from deprecated
create_singlethread_workqueue
- security improvement: remove unsafe ib_get_dma_mr (breaks lustre in
staging)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (75 commits)
staging/lustre: Disable InfiniBand support
iw_cxgb4: add fast-path for small REG_MR operations
cxgb4: advertise support for FR_NSMR_TPTE_WR
IB/core: correctly handle rdma_rw_init_mrs() failure
IB/srp: Fix infinite loop when FMR sg[0].offset != 0
IB/srp: Remove an unused argument
IB/core: Improve ib_map_mr_sg() documentation
IB/mlx4: Fix possible vl/sl field mismatch in LRH header in QP1 packets
IB/mthca: Move user vendor structures
IB/nes: Move user vendor structures
IB/ocrdma: Move user vendor structures
IB/mlx4: Move user vendor structures
IB/cxgb4: Move user vendor structures
IB/cxgb3: Move user vendor structures
IB/mlx5: Move and decouple user vendor structures
IB/{core,hw}: Add constant for node_desc
ipoib: Make ipoib_warn ratelimited
IB/mlx4/alias_GUID: Remove deprecated create_singlethread_workqueue
IB/ipoib_verbs: Remove deprecated create_singlethread_workqueue
IB/ipoib: Remove deprecated create_singlethread_workqueue
...
When processing a REG_MR work request, if fw supports the
FW_RI_NSMR_TPTE_WR work request, and if the page list for this
registration is <= 2 pages, and the current state of the mr is INVALID,
then use FW_RI_NSMR_TPTE_WR to pass down a fully populated TPTE for FW
to write. This avoids FW having to do an async read of the TPTE blocking
the SQ until the read completes.
To know if the current MR state is INVALID or not, iw_cxgb4 must track the
state of each fastreg MR. The c4iw_mr struct state is updated as REG_MR
and LOCAL_INV WRs are posted and completed, when a reg_mr is destroyed,
and when RECV completions are processed that include a local invalidation.
This optimization increases small IO IOPS for both iSER and NVMF.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Query firmware for the FW_PARAMS_PARAM_DEV_RI_FR_NSMR_TPTE_WR parameter.
If it exists and is 1, then advertise support for FR_NSMR_TPTE_WR to
the ULDs.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
A recent cleanup marked cxgb4_dcb_enabled as 'static', which is correct, but this ignored
how the symbol is also exported. In addition, the export can be compiled out when modules
are disabled, causing a harmless compiler warning in configurations for which it is not
used at all:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:282:12: error: 'cxgb4_dcb_enabled' defined but not used [-Werror=unused-function]
This removes the export and moves the function into the correct #ifdef so we only build
it when there are users.
Fixes: 50935857f8 ("cxgb4: mark symbols static where possible")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We get 1 warning when building kernel with W=1:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:2715:5: warning: no previous prototype for 'cxgb_setup_tc' [-Wmissing-prototypes]
In fact, this function is only used in the file in which it is
declared and don't need a declaration, but can be made static.
so this patch marks this function with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We get 10 warnings when building kernel with W=1:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:304:5: warning: no previous prototype for 'cxgb4_dcb_enabled' [-Wmissing-prototypes]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_uld.c:194:5: warning: no previous prototype for 'setup_sge_queues_uld' [-Wmissing-prototypes]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_uld.c:241:6: warning: no previous prototype for 'free_sge_queues_uld' [-Wmissing-prototypes]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_uld.c:268:5: warning: no previous prototype for 'cfg_queues_uld' [-Wmissing-prototypes]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_uld.c:344:6: warning: no previous prototype for 'free_queues_uld' [-Wmissing-prototypes]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_uld.c:353:5: warning: no previous prototype for 'request_msix_queue_irqs_uld' [-Wmissing-prototypes]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_uld.c:379:6: warning: no previous prototype for 'free_msix_queue_irqs_uld' [-Wmissing-prototypes]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_uld.c:393:6: warning: no previous prototype for 'name_msix_vecs_uld' [-Wmissing-prototypes]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_uld.c:433:6: warning: no previous prototype for 'enable_rx_uld' [-Wmissing-prototypes]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_uld.c:442:6: warning: no previous prototype for 'quiesce_rx_uld' [-Wmissing-prototypes]
In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
so this patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
iq is unsigned, so the error check for iq < 0 has no effect so errors
can slip past this check. Fix this by making iq signed and also
get_filter_steerq return a signed int so a -ve error can be returned.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change predecrement compare to post decrement compare to avoid an
unsigned integer wrap-around comparison when decrementing idx in
the while loop.
For example, when idx is zero, the current situation will
predecrement idx in the while loop, wrapping idx to the maximum
signed integer and cause out of bounds reads on rxq_info->msix_tbl[idx].
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove an open coded simple_open() function and replace file
operations references to the function with simple_open()
instead.
Generated by: scripts/coccinelle/api/simple_open.cocci
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for dropping matched packets in hardware. Also add support
for re-directing matched packets to a specified port in hardware.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for offloading u32 filter onto hardware. Links are stored
in a jump table to perform necessary jumps to match TCP/UDP header.
When inserting rules in the linked bucket, the TCP/UDP match fields
in the corresponding entry of the jump table are appended to the filter
rule before insertion. If a link is deleted, then all corresponding
filters associated with the link are also deleted. Also enable
hardware tc offload as a supported feature.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parse information sent by u32 into internal filter specification.
Add support for parsing several fields in IPv4, IPv6, TCP, and UDP.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable filters for non-offload configuration and add common api support
for setting and deleting filters in LE-TCAM region of the hardware.
IPv4 filters occupy one slot. IPv6 filters occupy 4 slots and must
be on a 4-slot boundary. IPv4 filters can not occupy a slot belonging
to IPv6 and the vice-versa is also true.
Filters are set and deleted asynchronously. Use completion to wait
for reply from firmware in order to allow for synchronization if needed.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move common filter code to separate files. Also fix the following
checkpatch checks.
CHECK: Comparison to NULL could be written "!f->l2t"
+ if (f->l2t == NULL) {
CHECK: spaces preferred around that '/' (ctx:VxV)
+ fwr->len16_pkd = htonl(FW_WR_LEN16_V(sizeof(*fwr)/16));
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were missing check for 25G and 100G while checking port speed,
which lead to less number of queues getting allocated for 25G & 100G
adapters and leading to low throughput. Adding the missing check for
both NIC and vNIC driver.
Also fixes port advertisement for 25G and 100G in ethtool output.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the retrn value check which testing the wrong variable
in cfg_queues_uld().
Fixes: 94cdb8bb99 ("cxgb4: Add support for dynamic allocation of
resources for ULD")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate resources dynamically to cxgb4's Upper layer driver's(ULD) like
cxgbit, iw_cxgb4 and cxgb4i. Allocate resources when they register with
cxgb4 driver and free them while unregistering. All the queues and the
interrupts for them will be allocated during ULD probe only and freed
during remove.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cxgb_mk_rx_data_ack() to remove duplicate
code to form CPL_RX_DATA_ACK hardware command.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cxgb_mk_abort_rpl() to remove duplicate
code to form CPL_ABORT_RPL hardware command.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cxgb_mk_abort_req() to remove duplicate code
to form CPL_ABORT_REQ hardware command.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cxgb_mk_close_con_req() to remove duplicate
code to form CPL_CLOSE_CON_REQ hardware command.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cxgb_mk_tid_release() to remove duplicate code
to form CPL_TID_RELEASE hardware command.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cxgb_compute_wscale() in libcxgb_cm.h to remove
it's duplicate definitions from cxgb4/cm.c and
cxgbit/cxgbit_cm.c.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cxgb_best_mtu() in libcxgb_cm.h to remove
it's duplicate definitions from cxgb4/cm.c and
cxgbit/cxgbit_cm.c
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cxgb_is_neg_adv() in libcxgb_cm.h to remove
it's duplicate definitions from cxgb4/cm.c and
cxgbit/cxgbit_cm.c.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cxgb_find_route6() in libcxgb_cm.c to remove
it's duplicate definitions from cxgb4/cm.c and
cxgbit/cxgbit_cm.c.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cxgb_find_route() in libcxgb_cm.c to remove
it's duplicate definitions from cxgb4/cm.c and
cxgbit/cxgbit_cm.c.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cxgb_get_4tuple() in libcxgb_cm.c to remove
it's duplicate definitions from cxgb4/cm.c and
cxgbit/cxgbit_cm.c.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The checksum provided by the device doesn't include the L3 headers,
as IPv6 expects
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for ndo_get_vf_config, also fill the default mac address
that will be provided to the VF by firmware, in case user doesn't
provide one. So user can get the default MAC address address also
through ndo_get_vf_config.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in dev_warn message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove including <linux/version.h> that don't need it.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we disable SRIOV, we used to unregister the netdev but wasn't
freed. But next time when the same netdev is registered, since the state
was in 'NETREG_UNREGISTERED', we used to hit BUG_ON in register_netdevice,
where it expects the state to be 'NETREG_UNINITIALIZED'.
Alloc netdev and register them while configuring SRIOV, and free them
when SRIOV is disabled. Also added a new function to setup ethernet
properties instead of using ether_setup. Set carrier off by default,
since we don't have to do any transmit on the interface.
Fixes: 7829451c69 ("cxgb4: Add control net_device for configuring PCIe VF")
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement set_tx_maxrate NDO to perform per queue tx rate limiting.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to bind/unbind specified tx queues to/from scheduling
classes. If a queue is already bound to a scheduling class, it is
unbound first and then bound to a new specified class.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to create tx traffic scheduling classes with specified
scheduling parameters. Return an existing class if a match is found
with same scheduling parameters.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new commmon infrastructure to allocate reosurces dynamically to
Upper layer driver's(ULD) when they register with cxgb4 driver and free
them during unregistering. All the queues and the interrupts for
them will be allocated during ULD probe only and freed during remove.
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At present the code to check in kdump kernel was not disabling
allocation of resources when CONFIG_CHELSIO_T4_DCB is defined, move the
code outside #defines so that it gets disabled irrespective of #define,
when in kdump kernel.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes for both merge conflicts.
Resolution work done by Stephen Rothwell was used
as a reference.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ndo_set_vf_mac support which allows to set the MAC address
for cxgb4vf interfaces from the host
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Issue:
For instance, the current APIs assume a 1-to-1 mapping of Network Ports,
Physical Functions and the SR-IOV Virtual Functions of those Physical
Functions. This is not the case with our cards where any Virtual
Function can be hooked up to any Port -- or any number of Ports the
current Linux APIs also assume only 1 Network Interface/Port can be
accessed per Virtual Function.
Another issue is that these APIs assume that the Administrative Driver
is attached to the Physical Function Associated with a Virtual Function.
This is not the case with our card where all administration is performed
by a Driver which is not attached to any of the Physical Functions which
have SR-IOV PCI Capabilities.
Another consequence of these assumptions is the inability to utilize all
of the cards SR-IOV resources. For instance, our cards have SR-IOV
Capabilities on Physical Functions 0..3 and the administrative Driver
attaches to Physical Function 4. Each of the Physical Functions 0..3 can
support up to 16 Virtual Functions. With the current Linux APIs, a
2-Port card would only be able to use the Virtual Functions on Physical
Function 0..1 and not allow the Virtual Functions on Physical Functions
2..3 to be used since there are no Ports 2..3 on a 2-Port card.
Fix:
Since the control node is always the netdevice for all VF ACL commands.
Created a dummy netdevice for each Physical Function from 0 to 3 through
which one could control their VFs. The device won't be associated with
any port, since it doesn't need to transmit/receive. Its purely used
for VF management purpose only. The device will be registered only when
VF for a particular PF is configured using PCI sysfs interface and
unregistered while pci_disable_sriov() for the PF is called.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Updates/fixes for iw_cxgb4 driver
- Updates/fixes for mlx5 driver
- Add flow steering and RSS API
- Add hardware stats to mlx4 and mlx5 drivers
- Add firmware version API for RDMA driver use
- Add the rxe driver (this is a software RoCE driver that makes any
Ethernet device a RoCE device)
- Fixes for i40iw driver
- Support for send only multicast joins in the cma layer
- Other minor fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=oZOO
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull base rdma updates from Doug Ledford:
"Round one of 4.8 code: while this is mostly normal, there is a new
driver in here (the driver was hosted outside the kernel for several
years and is actually a fairly mature and well coded driver). It
amounts to 13,000 of the 16,000 lines of added code in here.
Summary:
- Updates/fixes for iw_cxgb4 driver
- Updates/fixes for mlx5 driver
- Add flow steering and RSS API
- Add hardware stats to mlx4 and mlx5 drivers
- Add firmware version API for RDMA driver use
- Add the rxe driver (this is a software RoCE driver that makes any
Ethernet device a RoCE device)
- Fixes for i40iw driver
- Support for send only multicast joins in the cma layer
- Other minor fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (72 commits)
Soft RoCE driver
IB/core: Support for CMA multicast join flags
IB/sa: Add cached attribute containing SM information to SA port
IB/uverbs: Fix race between uverbs_close and remove_one
IB/mthca: Clean up error unwind flow in mthca_reset()
IB/mthca: NULL arg to pci_dev_put is OK
IB/hfi1: NULL arg to sc_return_credits is OK
IB/mlx4: Add diagnostic hardware counters
net/mlx4: Query performance and diagnostics counters
net/mlx4: Add diagnostic counters capability bit
Use smaller 512 byte messages for portmapper messages
IB/ipoib: Report SG feature regardless of HW UD CSUM capability
IB/mlx4: Don't use GFP_ATOMIC for CQ resize struct
IB/hfi1: Disable by default
IB/rdmavt: Disable by default
IB/mlx5: Fix port counter ID association to QP offset
IB/mlx5: Fix iteration overrun in GSI qps
i40iw: Add NULL check for puda buffer
i40iw: Change dup_ack_thresh to u8
i40iw: Remove unnecessary check for moving CQ head
...
The commit 637d3e9973 ("cxgb4: Discard the packet if the length is
greater than mtu") introduced a regression in the VLAN interface
performance when Tx VLAN offload is disabled.
Check if skb is tagged, regardless of whether it is hardware accelerated
or not. Presently we were checking only for hardware acclereated one,
which caused performance to drop to ~0.17Mbps on a 10GbE adapter for
VLAN interface, when tx vlan offload is turned off using ethtool.
The ethernet head length calculation was going wrong in this case, and
driver ended up dropping packets.
Fixes: 637d3e9973 ("cxgb4: Discard the packet if the length is greater than mtu")
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove including <linux/version.h> that don't need it.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export cxgbi_ppm_release() to release
ppod manager and cxgbi_tagmask_set() to
set tag mask, they are used by cxgb3i, cxgb4i
and cxgbit.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add common library module(libcxgb.ko) for
Chelsio drivers to remove duplicate code.
Code for iSCSI DDP Page Pod Manager is moved
from cxgb4.ko to libcxgb.ko. Earlier only cxgbit.ko
was using this code, now cxgb3i and cxgb4i will
also use common Page Pod manager code.
In future this module will have common connection
management and hardware specific code that can be
shared by multiple Chelsio drivers.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mellanox/mlx5/core/en.h
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
drivers/net/usb/r8152.c
All three conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Change t4fw_version.h to update latest firmware version number
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The issue comes when there are multiple threads attempting to use the
mailbox facility at the same time. The issue is the for the Virtual
Function Driver, the only way to get the Virtual Interface statistics
is to issue mailbox commands to ask the firmware for the VI Stats.
And, because the VI Stats command can only retrieve a smallish number of
stats per mailbox command, we have to issue three mailbox commands in quick
succession. When ethtool or netstat command to get interface stats and
interface up/down is run in a loop for every 0.1 sec, we observed
mailbox collisions. And out of the two commands one would fail with
the present code, since we don't queue the second command.
To overcome the above issue, added a queue to access the mailbox.
Whenever a mailbox command is issued add it to the queue. If its at the
head issue the mailbox command, else wait for the existing command to
complete. Usually command takes less than a milli-second to complete.
Also timeout from the loop, if the command under execution takes
long time to run.
In reality, the number of mailbox access collisions is going to be very
rare since no one runs such abusive script.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if interface is in Promiscuous mode/Allmulti mode synchronize
MAC addresses.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement callback in the driver for the new PCI bus driver
interface that allows the user to enable/disable SR-IOV
virtual functions in a device via the sysfs interface.
Deprecate module parameter used to configure SRIOV
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When is_kdump_kernel() is true, Forcing cxgb4 driver as Master so we can
reinitialize the Firmware/Chip. Also reduce memory usage by disabling
offload.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Updates to the new Intel X722 iWARP driver
- Updates to the hfi1 driver
- Fixes for the iw_cxgb4 driver
- Misc core fixes
- Generic RDMA READ/WRITE API addition
- SRP updates
- Misc ipoib updates
- Minor mlx5 updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=e+Zv
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"Primary 4.7 merge window changes
- Updates to the new Intel X722 iWARP driver
- Updates to the hfi1 driver
- Fixes for the iw_cxgb4 driver
- Misc core fixes
- Generic RDMA READ/WRITE API addition
- SRP updates
- Misc ipoib updates
- Minor mlx5 updates"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (148 commits)
IB/mlx5: Fire the CQ completion handler from tasklet
net/mlx5_core: Use tasklet for user-space CQ completion events
IB/core: Do not require CAP_NET_ADMIN for packet sniffing
IB/mlx4: Fix unaligned access in send_reply_to_slave
IB/mlx5: Report Scatter FCS device capability when supported
IB/mlx5: Add Scatter FCS support for Raw Packet QP
IB/core: Add Scatter FCS create flag
IB/core: Add Raw Scatter FCS device capability
IB/core: Add extended device capability flags
i40iw: pass hw_stats by reference rather than by value
i40iw: Remove unnecessary synchronize_irq() before free_irq()
i40iw: constify i40iw_vf_cqp_ops structure
IB/mlx5: Add UARs write-combining and non-cached mapping
IB/mlx5: Allow mapping the free running counter on PROT_EXEC
IB/mlx4: Use list_for_each_entry_safe
IB/SA: Use correct free function
IB/core: Fix a potential array overrun in CMA and SA agent
IB/core: Remove unnecessary check in ibnl_rcv_msg
IB/IWPM: Fix a potential skb leak
RDMA/nes: replace custom print_hex_dump()
...
The FID value in a ULP_MEMIO command needs to be set to an IQ ID of
a queue configured for our PF. The FID/IQ id is used to index into the
PCIE FID table, to find out on which function the DMA needs to be
issued. Essentially, every DMA needs to have the ingress queue. The exact
ingress queue doesn't matter, but it needs to be an ingress queue
associated with the function you want to see the DMA on.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When cxgb4 is enabled with CONFIG_CHELSIO_T4_DCB set, VI enable command
gets called with DCB enabled. But when we have a back to back setup with
DCB enabled on one side and non-DCB on the Peer side. Firmware doesn't
send any DCB_L2_CFG, and DCB priority is never set for Tx queue.
But driver resets the queue priority and state machine whenever there
is a link down, this patch fixes it by adding a check to reset only if
cxgb4_dcb_enabled() returns true.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for firmware errors in the mailbox command loop and report
them differently rather than simply timing out when the firmware goes
belly up.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When link goes down, from the interrupt handler DCB priority for the
Tx queues needs to be unset. We issue mbox command to unset the Tx queue
priority with negative timeout. In t4_wr_mbox_meat_timeout() do not sleep
when negative timeout is passed, since it is called from interrupt context.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv4/ip_gre.c
Minor conflicts between tunnel bug fixes in net and
ipv6 tunnel cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
An out of bounds read of 2 bytes was discovered in cxgb3 with KASAN.
t3_config_rss() expects both arrays it gets as parameters to have
terminators. setup_rss(), the caller, forgets to add a terminator to
one of the arrays. Thankfully the iteration in t3_config_rss() stops
anyway, but in the last iteration the check for the terminator
is an out of bounds read.
Add the missing terminator to rspq_map[].
Reported-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new /sys/kernel/debug/ support to dump firmware mailbox commands
and replies for debugging purpose.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new /sys/kernel/debug/ support to dump a firmware mailbox command
issued and replies for debugging purpose.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
replace the trylock by a full spin_lock and remove TX_LOCKED return value.
Followup patch will remove TX_LOCKED from the kernel.
Cc: Jon Mason <jdmason@kudzu.us>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware can send a set of asynchronous replies through FW_PORT_CMD
with DCBX information when that's negotiated with the Link Peer. The old
code always assumed that a FW_PORT_CMD reply was always a Get Port
Information message. This change conditionalizes the code to only handle
the Get Port Information messages and throws a warning if we don't
understand what we've been given.
Also refactor t4_handle_fw_rpl() so that core functionality performed by
t4_handle_get_port_info() for a specified port.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor t4_port_init() so that the core functionality is done by
t4_init_portinfo() for a particular port. Also rename variables to
sensible ones.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Decode and log port module error, unknown modules and unsupported
modules.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There could be race between t4_eth_xmit() and t4_free_sge_resources() while
freeing tx descriptors, take txq lock in t4_free_sge_resources(). We need
to stop the xmit frame path which runs in bottom half context while
unloading the driver using _bh variant of the lock. This is to prevent
the deadlock between xmit and driver unload.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new routine to print out general adapter information (various version
numbers, adapter name, part number, serial number, etc.) and remove
redundant information dumped in the Port Information.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts were two cases of simple overlapping changes,
nothing serious.
In the UDP case, we need to add a hlist_add_tail_rcu()
to linux/rculist.h, because we've moved UDP socket handling
away from using nulls lists.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix memory leak in iwlwifi, from Matti Gottlieb.
2) Add missing registration of netfilter arp_tables into initial
namespace, from Florian Westphal.
3) Fix potential NULL deref in DecNET routing code.
4) Restrict NETLINK_URELEASE to truly bound sockets only, from Dmitry
Ivanov.
5) Fix dst ref counting in VRF, from David Ahern.
6) Fix TSO segmenting limits in i40e driver, from Alexander Duyck.
7) Fix heap leak in PACKET_DIAG_MCLIST, from Mathias Krause.
8) Ravalidate IPV6 datagram socket cached routes properly, particularly
with UDP, from Martin KaFai Lau.
9) Fix endian bug in RDS dp_ack_seq handling, from Qing Huang.
10) Fix stats typing in bcmgenet driver, from Eric Dumazet.
11) Openvswitch needs to orphan SKBs before ipv6 fragmentation handing,
from Joe Stringer.
12) SPI device reference leak in spi_ks8895 PHY driver, from Mark Brown.
13) atl2 doesn't actually support scatter-gather, so don't advertise the
feature. From Ben Hucthings.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (72 commits)
openvswitch: use flow protocol when recalculating ipv6 checksums
Driver: Vmxnet3: set CHECKSUM_UNNECESSARY for IPv6 packets
atl2: Disable unimplemented scatter/gather feature
net/mlx4_en: Split SW RX dropped counter per RX ring
net/mlx4_core: Don't allow to VF change global pause settings
net/mlx4_core: Avoid repeated calls to pci enable/disable
net/mlx4_core: Implement pci_resume callback
net: phy: spi_ks8895: Don't leak references to SPI devices
net: ethernet: davinci_emac: Fix platform_data overwrite
net: ethernet: davinci_emac: Fix Unbalanced pm_runtime_enable
qede: Fix single MTU sized packet from firmware GRO flow
qede: Fix setting Skb network header
qede: Fix various memory allocation error flows for fastpath
tcp: Merge tx_flags and tskey in tcp_shifted_skb
tcp: Merge tx_flags and tskey in tcp_collapse_retrans
drivers: net: cpsw: fix wrong regs access in cpsw_ndo_open
tcp: Fix SOF_TIMESTAMPING_TX_ACK when handling dup acks
openvswitch: Orphan skbs before IPv6 defrag
Revert "Prevent NUll pointer dereference with two PHYs on cpsw"
VSOCK: Only check error on skb_recv_datagram when skb is NULL
...
VPD
Add pci_set_vpd_size() (Hariprasad Shenai)
cxgb4: Set VPD size so we can read both VPD structures (Hariprasad Shenai)
Freescale i.MX6 host bridge driver
Revert "PCI: imx6: Add support for active-low reset GPIO" (Fabio Estevam)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=oW8E
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.6-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"These are fixes for two issues:
- The VPD parsing code we added for v4.6 keeps some devices from
crashing, but also keeps cxgb4 from reading non-standard extra VPD
data that is relies on. Hariprasad added a way for the driver to
specify how much VPD is valid.
- The i.MX6 active-low reset GPIO support we added in v4.5 caused
regressions on some boards, so we're reverting that.
VPD:
Add pci_set_vpd_size() (Hariprasad Shenai)
cxgb4: Set VPD size so we can read both VPD structures (Hariprasad Shenai)
Freescale i.MX6 host bridge driver:
Revert "PCI: imx6: Add support for active-low reset GPIO" (Fabio Estevam)"
* tag 'pci-v4.6-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
cxgb4: Set VPD size so we can read both VPD structures
PCI: Add pci_set_vpd_size() to set VPD size
Revert "PCI: imx6: Add support for active-low reset GPIO"
Chelsio adapters have two VPD structures stored in the VPD:
- offset 0x000: an abbreviated VPD, and
- offset 0x400: the complete VPD.
After 104daa71b3 ("PCI: Determine actual VPD size on first access"), the
PCI core computes the valid VPD size by parsing the VPD starting at offset
0x0. That size only includes the abbreviated VPD structure, so reads of
the complete VPD at 0x400 fail.
Explicitly set the VPD size with pci_set_vpd_size() so the driver can read
both VPD structures.
[bhelgaas: changelog, split patches, rename to pci_set_vpd_size() and
return int (not ssize_t)]
Fixes: 104daa71b3 ("PCI: Determine actual VPD size on first access")
Tested-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Stop all Ethernet RX Queues before freeing up various Ingress/Egress
Queues, etc. We were seeing cases of Ingress Queues not getting serviced
during the shutdown process leading to Ingress Paths jamming up through
the chip and blocking the shutdown effort itself.
One such case involved the Firmware sending a "Flush Token" through the
ULP-TX -> ULP-RX path for an Ethernet TX Queue being freed in order to
make sure there weren't any remaining TX Work Requests in the pipeline.
But the return path was stalled by Ingress Data unable to be delivered to
the Host because those Ingress Queues were no longer being serviced.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Message level can be set through ethtool, so deprecate module parameter
which is used to set the same.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull more SCSI target updates from Nicholas Bellinger:
"This series contains cxgb4 driver prerequisites for supporting iscsi
segmentation offload (ISO), that will be utilized for a number of
future v4.7 developments in iscsi-target for supporting generic hw
offloads"
* 'for-next-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
cxgb4: update Kconfig and Makefile
cxgb4: add iSCSI DDP page pod manager
cxgb4, iw_cxgb4: move delayed ack macro definitions
cxgb4: move VLAN_NONE macro definition
cxgb4: update struct cxgb4_lld_info definition
cxgb4: add definitions for iSCSI target ULD
cxgb4, cxgb4i: move struct cpl_rx_data_ddp definition
cxgb4, iw_cxgb4, cxgb4i: remove duplicate definitions
cxgb4, iw_cxgb4: move definitions to common header file
cxgb4: large receive offload support
cxgb4: allocate resources for CXGB4_ULD_ISCSIT
cxgb4: add new ULD type CXGB4_ULD_ISCSIT
add files for common page pod manager,
both iSCSI initiator and target ULDs will
use common ppod manager for DDP.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Acked-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Chelsio iSCSI target offload driver
will register with cxgb4 driver as ULD of type
CXGB4_ULD_ISCSIT.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Acked-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The Queue Set Configuration code was always reserving room for a
Forwarded interrupt Queue even in the cases where we weren't using it.
Figure out how many Ports and Queue Sets we can support. This depends on
knowing our Virtual Function Resources and may be called a second time
if we fall back from MSI-X to MSI Interrupt Mode. This change fixes that
problem.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This avoids a race condition where a system that has network devices set up
to be automatically configured and we get the first Port Link Status
message from the firmware on the Asynchronous Firmware Event Queue before
we've enabled interrupts. If that happens, we end up losing the interrupt
and never realizing that the links has actually come up.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function t4vf_wait_dev_ready() is already called in t4vf_prep_adapter(),
no need to call it again in adap_init0().
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds a new function t4vf_fl_pkt_align() and use the same in SGE
initialization code to find out freelist packet alignment
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
T4 and T5 hardware will not coalesce Free List PCI-E Fetch Requests if
the Host Driver provides more Free List Pointers than the Fetch Burst
Minimum value. So if we set FBMIN to 64 bytes and the Host Driver
supplies 128 bytes of Free List Pointer data, the hardware will issue two
64-byte PCI-E Fetch Requests rather than a single coallesced 128-byte
Fetch Request. T6 fixes this. So, for T4/T5 we set the FBMIN value to 128
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use freelist capacity instead of freelist size while checking, if
freelist needs to be refilled
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/phy/bcm7xxx.c
drivers/net/phy/marvell.c
drivers/net/vxlan.c
All three conflicts were cases of simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The vpd strings are left justified, in a fixed length array, with possible
trailing white space and no NUL. So fix them up before calling kstrto*().
This is a recent regression which causes cxgb3 to fail to load.
Fixes: e72c932 ("cxgb3: Convert simple_strtoul to kstrtox")
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series provides support for iWARP applications to specify a TOS
value and have that map to a VLAN Priority for iw_cxgb4 iWARP connections.
In iw_cxgb4, when allocating an L2T entry, pass the skb_priority based
on the tos value in the cm_id. Also pass the correct tos value during
connection setup so the passive side gets the client's desired tos.
When sending the FLOWC work request to FW, if the egress device is
in a vlan, then use the vlan priority bits as the scheduling class.
This allows associating RDMA connections with scheduling classes to
provide traffic shaping per flow.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 115b56af88 ("cxgb4: Update mps_tcam output to include T6
fields") from Dec 23, 2015, leads to the following static checker
warning:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_debugfs.c:1735
mps_tcam_show()
warn: we tested 'lookup_type' before and it was 'true'
Fixing it.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cphy_ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since t4_alloc_mem can be failed in memory pressure,
if not properly handled, NULL dereference could be happened.
Signed-off-by: Insu Yun <wuninsu@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove deprecated module parameters, and mark one parameter as
deprecated.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CLIP is always enabled and hardware uses 2 TID entries instead of 4 for
IPv6 in CLIP mode.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SGE context congestion map changed from 4 to 8 priority per port
in T6 as there are only 2 channels.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In T6, MPS classification has a 512 deep TCAM to do the match lookup.
Each entry has 80x2b sets containing 48 bit MAC address, port number,
VLAN Valid/ID, VNI, lookup type (outer or inner packet header).
[71:48] bit locations are overloaded for outer vs. inner lookup types.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updating Congestion Channel/Priority Map in Congestion Manager Context
for T6. In T6 port 0 is mapped to channel 0 and port 1 is mapped to
channel 1. For 2 port T4/T5 adapter, port 0 is mapped to channel 0,1 and
port 1 is mapped to channel 2,3
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ingress padding boundary values got changed for T6.
T5: 0=32B 1=64B 2=128B 3=256B 4=512B 5=1024B 6=2048B 7=4096B
T6: 0=8B 1=16B 2=32B 3=64B 4=128B 5=128B 6=256B 7=512B
Updating the driver to set the correct boundary values in SGE_CONTROL to
32B.
Also, need to take care of this fl alignment change when calculating the
next packet offset.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updated pm_stats code to display input FIFO wait (index 5) and read
latency (index 7) counters for T6 adapters
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the upper level protocols like rdma, iscsi have their own offload rx
queues, so instead of using the generic naming convention be specific
while naming them. Improves code readability
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check if the device get enough bandwidth from the entire PCI chain to
satisfy its capabilities. This patch determines the PCIe device's
bandwidth capabilities by reading its PCIe Link Capabilities registers
and then call the pcie_get_minimum_link function to ensure that the
adapter is hooked into a slot which is capable of providing the
necessary bandwidth capabilities.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original work by Michael Werner <werner@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original work by Michael Werner <werner@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original work by Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a warn message when clip table overflows. If clip table isn't
allocated, return from cxgb4_clip_release() to avoid panic.
Disable offload if clip isn't enabled in the hardware.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cmac_ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Free List DMA Mapping Errors to SGE Queue info for
Free Lists. Add Free List "Low" counter to count the number of times we
see the number of pointers that we _think_ the hardware sees in the
Free List below the Egress Threshold.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The WR headers may not fit within one descriptor.
So we need to deal with wrap-around here.
Based on original patch by Pranjal Joshi <pjoshi@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change mutual exclusion mechanism to prevent multiple threads of
execution from running in service_ofldq() at the same time. The old
mechanism used an implicit guard on the down-call path and none on the
restart path and wasn't working. This checking makes the mechanism
explicit and is much easier to understand as a result.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use helper macro ACCESS_ONCE() to load from the SGE status page
to prevent the compiler loading multiple times.
Based on original work by Mike Werner <werner@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the simple_strtoul function is obsolete. This patch replace it by
kstrtox.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NAPI drivers no longer need to observe a particular protocol
to benefit from busy polling (CONFIG_NET_RX_BUSY_POLL=y)
napi_hash_add() and napi_hash_del() are automatically called
from core networking stack, respectively from
netif_napi_add() and netif_napi_del()
This patch depends on free_netdev() and netif_napi_del() being
called from process context, which seems to be the norm.
Drivers might still prefer to call napi_hash_del() on their
own, since they might combine all the rcu grace periods into
a single one, knowing their NAPI structures lifetime, while
core networking stack has no idea of a possible combining.
Once this patch proves to not bring serious regressions,
we will cleanup drivers to either remove napi_hash_del()
or provide appropriate rcu grace periods combining.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We would like to automatically provide busy polling support
to all NAPI drivers, without them having to implement anything.
skb_mark_napi_id() can be called from napi_gro_receive() and
napi_get_frags().
Few drivers are still calling skb_mark_napi_id() because
they use netif_receive_skb(). They should eventually call
napi_gro_receive() instead. I will leave this to drivers
maintainers.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- "Checksum offload support in user space" enablement
- Misc cxgb4 fixes, add T6 support
- Misc usnic fixes
- 32 bit build warning fixes
- Misc ocrdma fixes
- Multicast loopback prevention extension
- Extend the GID cache to store and return attributes of GIDs
- Misc iSER updates
- iSER clustering update
- Network NameSpace support for rdma CM
- Work Request cleanup series
- New Memory Registration API
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=bBIY
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"This is my initial round of 4.4 merge window patches. There are a few
other things I wish to get in for 4.4 that aren't in this pull, as
this represents what has gone through merge/build/run testing and not
what is the last few items for which testing is not yet complete.
- "Checksum offload support in user space" enablement
- Misc cxgb4 fixes, add T6 support
- Misc usnic fixes
- 32 bit build warning fixes
- Misc ocrdma fixes
- Multicast loopback prevention extension
- Extend the GID cache to store and return attributes of GIDs
- Misc iSER updates
- iSER clustering update
- Network NameSpace support for rdma CM
- Work Request cleanup series
- New Memory Registration API"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (76 commits)
IB/core, cma: Make __attribute_const__ declarations sparse-friendly
IB/core: Remove old fast registration API
IB/ipath: Remove fast registration from the code
IB/hfi1: Remove fast registration from the code
RDMA/nes: Remove old FRWR API
IB/qib: Remove old FRWR API
iw_cxgb4: Remove old FRWR API
RDMA/cxgb3: Remove old FRWR API
RDMA/ocrdma: Remove old FRWR API
IB/mlx4: Remove old FRWR API support
IB/mlx5: Remove old FRWR API support
IB/srp: Dont allocate a page vector when using fast_reg
IB/srp: Remove srp_finish_mapping
IB/srp: Convert to new registration API
IB/srp: Split srp_map_sg
RDS/IW: Convert to new memory registration API
svcrdma: Port to new memory registration API
xprtrdma: Port to new memory registration API
iser-target: Port to new memory registration API
IB/iser: Port to new fast registration API
...
Here's the "big" driver core updates for 4.4-rc1. Primarily a bunch of
debugfs updates, with a smattering of minor driver core fixes and
updates as well.
All have been in linux-next for a long time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlY6ePQACgkQMUfUDdst+ymNTgCgpP0CZw57GpwF/Hp2L/lMkVeo
Kx8AoKhEi4iqD5fdCQS9qTfomB+2/M6g
=g7ZO
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here's the "big" driver core updates for 4.4-rc1. Primarily a bunch
of debugfs updates, with a smattering of minor driver core fixes and
updates as well.
All have been in linux-next for a long time"
* tag 'driver-core-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
debugfs: Add debugfs_create_ulong()
of: to support binding numa node to specified device in devicetree
debugfs: Add read-only/write-only bool file ops
debugfs: Add read-only/write-only size_t file ops
debugfs: Add read-only/write-only x64 file ops
debugfs: Consolidate file mode checks in debugfs_create_*()
Revert "mm: Check if section present during memory block (un)registering"
driver-core: platform: Provide helpers for multi-driver modules
mm: Check if section present during memory block (un)registering
devres: fix a for loop bounds check
CMA: fix CONFIG_CMA_SIZE_MBYTES overflow in 64bit
base/platform: assert that dev_pm_domain callbacks are called unconditionally
sysfs: correctly handle short reads on PREALLOC attrs.
base: soc: siplify ida usage
kobject: move EXPORT_SYMBOL() macros next to corresponding definitions
kobject: explain what kobject's sd field is
debugfs: document that debugfs_remove*() accepts NULL and error values
debugfs: Pass bool pointer to debugfs_create_bool()
ACPI / EC: Fix broken 64bit big-endian users of 'global_lock'
Update ethtool get_drvinfo to display regdump len and also update
firmware string version print to display N/A in case FW isn't present
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the ethtool set_settings() routine we need to remember our old L1
Configuration in case the firmware rejects the request and then restore
that.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For {1, 10, 40} Gb/s. Prohibiting turning off autonegotiation isn't anywhere
in the standard.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Align the ethtool get stats settings with the rest so it looks uniform
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
t4_check_fw_version() can return several error codes (-EINVAL, -EBUSY,
-EAGAIN). The present code sets the adapter state to UNINIT only if its
an EFAULT. In all the error cases set the adapter to uninitialized state.
In t4_check_fw_version() if call to t4_get_fw_version() fails, repeat the
operation a few times before returning failure.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we get garbage from the firmware with weird Port Speeds,
etc. we should emit a warning regarding unsupported speeds rather than
use the bogus default of "10Mbps" which isn't even an option in the
firmware Port Information message
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware team added a new Device Log Facility FW_DEVLOG_FACILITY_CF,
but the driver has been decoding Device Log messages with that Facility as
"(NULL)", fixing it.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
T4 doesn't have the Shadow copy of the register which we can read without
side effect. So don't read mbox control register for T4 adapter
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update T4/T5/T6 adapter register ranges so that it doesn't read non
existent registers when dumped using ethtool
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Its a bit odd that debugfs_create_bool() takes 'u32 *' as an argument,
when all it needs is a boolean pointer.
It would be better to update this API to make it accept 'bool *'
instead, as that will make it more consistent and often more convenient.
Over that bool takes just a byte.
That required updates to all user sites as well, in the same commit
updating the API. regmap core was also using
debugfs_{read|write}_file_bool(), directly and variable types were
updated for that to be bool as well.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds support for ethtool get time stamp ioctl, which is used by
tcpdump to get the supported time stamp types
eg: tcpdump -i eth5 -J
Time stamp types for eth5 (use option -j to set):
host (Host)
adapter_unsynced (Adapter, not synced with system time)
Adds support for adapter unsynced mode, by adding SIOCSHWTSTAMP support
in driver.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Incorporate fw_ldst_cmd structure change for new firmware and also
update version string for the same
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The write-combining configuration register SGE_STAT_CFG_A needs to
be configured after FW initializes the adapter, else FW will reset
the configuration
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 0aac3f56d4 ("cxgb4: Add comment for calculate tx flits
and sge length code") introduced a regression where tx flit calculation
is going wrong, which can lead to data corruption, hang, stall and
write-combining failure. Fixing it.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c: In function ‘init_one’:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:4579:8: warning: ‘chip’ may be used uninitialized in this function [-Wmaybe-uninitialized]
chip |= CHELSIO_CHIP_CODE(CHELSIO_T4, pl_rev);
^
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:4571:11: note: ‘chip’ was declared here
int ver, chip;
^
Fixes: d86bd29e0b ("cxgb4/cxgb4vf: read the correct bits of PL Who Am I register")
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Forcing uninitialized state allows us to upgrade and reinitialize
the adapter.
FW_VERSION_T4 = 1.4.0.0
FW_VERSION_T5 = 0.0.0.0
FW_VERSION_T6 = 0.0.0.0
At this point driver supports above and greater than above version.
If FW in adapter < min FW_VERSION driver supports tries to upgrade the FW
If FW in adapter >= FW_VERSION driver supports then it follows normal path
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
You can't use kstrtoul() with an int or it causes memory corruption.
Also j should be unsigned or we have underflow bugs.
I considered changing "j" to unsigned long but everything fits in a u32.
Fixes: 8e3d04fd7d ('cxgb4: Add MPS tracing support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle TRACE_PKT, stack can sniff them on the first port
Add debubfs enrty to configure tracing for offload traffic like iWARP
& iSCSI for debugging purpose.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/cavium/Kconfig
The cavium conflict was overlapping dependency
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add debugfs support to dump tid info like stid, sftid, tids, atid and
hwtids
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For T4 adapter, offloaded servers tid for IPv4 connections are
allocated from filter region. So add a new field for server filter tid if
server tid is allocated from filter region.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the tid info, differentiate from which region the TID is allocated
from. It can be from TCAM region or HASH region.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding more details to sge qinfo for debugging purpose.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add or remove some tabs so that statements line up correctly.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were missing curly braces so it means we call add_debugfs_mem()
unintentionally.
Fixes: 3ccc6cf74d ('cxgb4: Adds support for T6 adapter')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Read the correct bits of PL Who Am I for the Source PF field which has
changed in T6
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to dump edc bist status for ECC data errors
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add debug support to dump memory address ranges of various hardware
modules of the adapter.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VF driver was reading incorrect freelist congestion notification threshold
for FLM queues when packing is enabled for T5 and T6 adapter. Fixing it
now.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adapter can go for a toss, if cxgb4 is loaded as slave and we try to
upgrade the firmware. So add a check for the same before flashing
firmware using ethtool.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add debugfs entry 'use_backdoor' to enable backdoor access to read sge
context. By default, we read sge context's via firmware. In case of FW
issues, one can enable backdoor access via debugfs to dump sge context
for debugging purpose.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since finally DCB traffic management is still handled by firmware,
allow firmware to be fully programmed and queried even in host
managed state for the cases where this was previously rejected.
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This keeps app format passed to firmware the same irrespective
of DCBx version in use.
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we don't have access to the new User GTS (T5+), use the old doorbell
mechanism; otherwise use the new BAR2 mechanism.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updating the driver to read the stats of only available channels. T6 and
later has only 2 channels
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver was retrieving the parameters for the bounds of its
slice of the L2T from the firmware and then throwing those away and
using the entire table. This corrects that problem.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Part of commit 49aa284fe64c4c1 ("cxgb4: Add support for devlog")
change introduced a real bug where the Device Log Sequence Numbers are
no longer being converted from firmware Big-Endian to local CPU-Endian
format.
This patch moves all of the translation into the devlog_show() routine.
The only endianness code now in devlog_open() is the small loop to find the
earliest (lowest Sequence Number) Device Log entry in the circular buffer.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use kvfree() instead of open-coding it.
Signed-off-by: Pekka Enberg <penberg@kernel.org>
Cc: Hariprasad S <hariprasad@chelsio.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use kvfree() instead of open-coding it.
Signed-off-by: Pekka Enberg <penberg@kernel.org>
Cc: Santosh Raspatur <santosh@chelsio.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking updates from David Miller:
1) Add TX fast path in mac80211, from Johannes Berg.
2) Add TSO/GRO support to ibmveth, from Thomas Falcon
3) Move away from cached routes in ipv6, just like ipv4, from Martin
KaFai Lau.
4) Lots of new rhashtable tests, from Thomas Graf.
5) Run ingress qdisc lockless, from Alexei Starovoitov.
6) Allow servers to fetch TCP packet headers for SYN packets of new
connections, for fingerprinting. From Eric Dumazet.
7) Add mode parameter to pktgen, for testing receive. From Alexei
Starovoitov.
8) Cache access optimizations via simplifications of build_skb(), from
Alexander Duyck.
9) Move page frag allocator under mm/, also from Alexander.
10) Add xmit_more support to hv_netvsc, from KY Srinivasan.
11) Add a counter guard in case we try to perform endless reclassify
loops in the packet scheduler.
12) Extern flow dissector to be programmable and use it in new "Flower"
classifier. From Jiri Pirko.
13) AF_PACKET fanout rollover fixes, performance improvements, and new
statistics. From Willem de Bruijn.
14) Add netdev driver for GENEVE tunnels, from John W Linville.
15) Add ingress netfilter hooks and filtering, from Pablo Neira Ayuso.
16) Fix handling of epoll edge triggers in TCP, from Eric Dumazet.
17) Add an ECN retry fallback for the initial TCP handshake, from Daniel
Borkmann.
18) Add tail call support to BPF, from Alexei Starovoitov.
19) Add several pktgen helper scripts, from Jesper Dangaard Brouer.
20) Add zerocopy support to AF_UNIX, from Hannes Frederic Sowa.
21) Favor even port numbers for allocation to connect() requests, and
odd port numbers for bind(0), in an effort to help avoid
ip_local_port_range exhaustion. From Eric Dumazet.
22) Add Cavium ThunderX driver, from Sunil Goutham.
23) Allow bpf programs to access skb_iif and dev->ifindex SKB metadata,
from Alexei Starovoitov.
24) Add support for T6 chips in cxgb4vf driver, from Hariprasad Shenai.
25) Double TCP Small Queues default to 256K to accomodate situations
like the XEN driver and wireless aggregation. From Wei Liu.
26) Add more entropy inputs to flow dissector, from Tom Herbert.
27) Add CDG congestion control algorithm to TCP, from Kenneth Klette
Jonassen.
28) Convert ipset over to RCU locking, from Jozsef Kadlecsik.
29) Track and act upon link status of ipv4 route nexthops, from Andy
Gospodarek.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1670 commits)
bridge: vlan: flush the dynamically learned entries on port vlan delete
bridge: multicast: add a comment to br_port_state_selection about blocking state
net: inet_diag: export IPV6_V6ONLY sockopt
stmmac: troubleshoot unexpected bits in des0 & des1
net: ipv4 sysctl option to ignore routes when nexthop link is down
net: track link-status of ipv4 nexthops
net: switchdev: ignore unsupported bridge flags
net: Cavium: Fix MAC address setting in shutdown state
drivers: net: xgene: fix for ACPI support without ACPI
ip: report the original address of ICMP messages
net/mlx5e: Prefetch skb data on RX
net/mlx5e: Pop cq outside mlx5e_get_cqe
net/mlx5e: Remove mlx5e_cq.sqrq back-pointer
net/mlx5e: Remove extra spaces
net/mlx5e: Avoid TX CQE generation if more xmit packets expected
net/mlx5e: Avoid redundant dev_kfree_skb() upon NOP completion
net/mlx5e: Remove re-assignment of wq type in mlx5e_enable_rq()
net/mlx5e: Use skb_shinfo(skb)->gso_segs rather than counting them
net/mlx5e: Static mapping of netdev priv resources to/from netdev TX queues
net/mlx4_en: Use HW counters for rx/tx bytes/packets in PF device
...
This howto made sense in the 1990s when users had to manually configure
ISA cards with jumpers or vendor utilities, but with the implementation
of PCI it became increasingly less and less relevant, to the point where
it has been well over a decade since I last updated it. And there is
no value in anyone else taking over updating it either.
However the references to it continue to spread as boiler plate text
from one Kconfig file into the next. We are not doing end users any
favours by pointing them at this old document, so lets kill it with
fire, once and for all, to hopefully stop any further spread.
No code is changed in this commit, just Kconfig help text.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no reason to perform a buffer copy for the firmware name. This
also avoids a (currently impossible with current callers) NULL dereference
if there was no matching firmware.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enhance cxgb4_t4_bar2_sge_qregs() and cxgb4_bar2_sge_qregs() to support T4
user mode mappings. Update all the current users as well.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The patch e85c9a7abfa4: ("cxgb4/cxgb4vf: Add code to calculate T5 BAR2
Offsets for SGE Queue Registers") from Dec 3, 2014, leads to the
following static checker warning:
drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:5358
t4_bar2_sge_qregs()
warn: should '(qid >> qpp_shift) << page_shift' be a 64 bit type?
This patch fixes it
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TP_PIO_{ADDR,DATA} registers are are in conflict with the firmware's
use of these registers. Added a routine to access it through FW LDST
cmd.
Access all TP_PIO_{ADDR,DATA} register access through new routine if FW
is alive. If firmware is dead, than fall back to indirect access.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Grab the Adapter MAC Address out of the VPD and use it for the "debug"
network interface when either we can't contact the firmware
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
t4_link_start() was completely misnamed. It does _not_ start up the
link. It merely does the L1 Configuration for the link. The Link Up
process is started automatically by the firmware when the number of
enabled Virtual Interfaces on a port goes from 0 to 1. So renaming
this routine to t4_link_l1cfg() for better documentation.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add function to flush the sge ec context cache, and utilize
this new function in the driver
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Free VI interfaces in remove routine. If we don't do this then the
firmware will never drop the physical link to the peer.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove ethtool get/set support for wake on lan, adapter doesn't support
it.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support in ethtool to dump loopback port statistics
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support in ethtool to dump adapter channel stats
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool support to get adapter specific hardware statistics
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds vnic driver register related changes for T6 adapter
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds NIC driver related changes for T6 adapter. Register related
changes, MC related changes, VF related changes, doorbell related
changes, debugfs changes, etc
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds new macro is_t6 and adds the register address range for T6 adapter
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused function cxgb4_enable_db_coalescing() and
cxgb4_disable_db_coalescing()
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes variable name 'fn' to 'pf' of structure adapter.
A 'fn' usually stands for PCI function which could be a PF or a VF.
However, the use of this particular variable is explicitly limited to PF
only. So, be specific about it in the variable name.
Also corrects arguments passed for fn t4_ofld_eq_free, t4_ctrl_eq_free,
t4_eth_eq_free, t4_iq_free, t4_alloc_vi, t4_fw_hello, t4_wr_mbox and
t4_cfg_pfvf function.
Also renames cxgb4_t4_bar2_sge_qregs to t4_bar2_sge_qregs and renames
the latter function name in cxgb4vf driver to t4vf_bar2_sge_qregs to
avoid conflicts. Also fixes alignment for these function.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add debugfs entry to inject Freelist starvation, used only for debugging
purpose.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for flashing 10GBaseT adapter with BCM 84834 PHY and
Aquantia AQ1202 PHY.
Updating of the PHY firmware must happen before the INITIALIZE_CMD.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some T4/T5 registers that were included incorrectly.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
replace ntoh{s,l} and hton{s,l} calls with the generic byteorder in
cxgb4/t4_hw.c file
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup few MACROS left out in t4_hw.h to be consistent with the
existing ones. Also replace few hardcoded values with MACROS. Also
update comments for some code
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implements t4_init_rss_mode() to initialize the rss_mode for all the ports. If
Tunnel All Lookup isn't specified in the global RSS Configuration, then we need
to specify a default Ingress Queue for any ingress packets which aren't hashed.
We'll use our first ingress queue.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pktgen sends raw udp packets and bypasses most of the
linux networking stack. User can specify different packet sizes.
Hence we need to discard the packet if the length is greater than mtu
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds device node to ULD info. Use the node info to alloc_ring() for ctrl
TX queues
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Passes a Congestion Channel Map to t4_sge_alloc_rxq()
for the Ethernet RX Queues based on the MPS Buffer Group Map
of the TX Channel rather than just the TX Channel Map.
Also, in t4_sge_alloc_rxq() for T5, setting up the
Congestion Manager values of the new RX Ethernet Queue is
done by firmware now.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also changed the name of t4_hw.c:get_mps_bg_map() to t4_get_mps_bg_map()
and make it an exported routine with a definition in cxgb4.h.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to make sure that the Free List Size, in pointers, is at
least 2 Egress Queue Units (8 pointers/each) larger than the SGE's Egress
Congestion Threshold (in pointers).
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6559a7e829 ("cxgb4: Cleanup macros so they follow the same
style and look consistent") introduced a regression where reading MC1
memory in adapters where MC0 isn't present or MC0 size is not equal to MC1
size caused the adapter to crash due to incorrect computation of memoffset.
Fix is to read the size of MC0 instead of MC1 for offset calculation
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull fourth vfs update from Al Viro:
"d_inode() annotations from David Howells (sat in for-next since before
the beginning of merge window) + four assorted fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
RCU pathwalk breakage when running into a symlink overmounting something
fix I_DIO_WAKEUP definition
direct-io: only inc/dec inode->i_dio_count for file systems
fs/9p: fix readdir()
VFS: assorted d_backing_inode() annotations
VFS: fs/inode.c helpers: d_inode() annotations
VFS: fs/cachefiles: d_backing_inode() annotations
VFS: fs library helpers: d_inode() annotations
VFS: assorted weird filesystems: d_inode() annotations
VFS: normal filesystems (and lustre): d_inode() annotations
VFS: security/: d_inode() annotations
VFS: security/: d_backing_inode() annotations
VFS: net/: d_inode() annotations
VFS: net/unix: d_backing_inode() annotations
VFS: kernel/: d_inode() annotations
VFS: audit: d_backing_inode() annotations
VFS: Fix up some ->d_inode accesses in the chelsio driver
VFS: Cachefiles should perform fs modifications on the top layer only
VFS: AF_UNIX sockets should call mknod on the top layer only
set_filter_wr is requesting __GFP_NOFAIL allocation although it can return
ENOMEM without any problems obviously (t4_l2t_set_switching does that
already). So the non-failing requirement is too strong without any
obvious reason. Drop __GFP_NOFAIL and reorganize the code to have the
failure paths easier.
The same applies to _c4iw_write_mem_dma_aligned which uses __GFP_NOFAIL
and then checks the return value and returns -ENOMEM on failure. This
doesn't make any sense what so ever. Either the allocation cannot fail or
it can.
del_filter_wr seems to be safe as well because the filter entry is not
marked as pending and the return value is propagated up the stack up to
c4iw_destroy_listen.
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Cc: David Rientjes <rientjes@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Dave Chinner <david@fromorbit.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Hariprasad S <hariprasad@chelsio.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix up some ->d_inode accesses in the chelsio driver.
(1) FILE_DATA() should just be replaced with file_inode().
(2) set_debugfs_file_size() should be removed and debugfs_create_file_size()
should be used to create the file.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add comment for tx filt and sge length calucaltion code, also remove
a hardcoded value
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fl_starv_thres could be different from adapter to adapter, don't use
hardcoded values
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows a significant latency drop for packets of sizes between 128 and 192
bytes
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the Chelsio Ethernet drivers to use the dma_rmb/wmb calls instead of
the full barriers in order to improve performance.
Cc: Santosh Raspatur <santosh@chelsio.com>
Cc: Hariprasad S <hariprasad@chelsio.com>
Cc: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/asix_common.c
drivers/net/usb/sr9800.c
drivers/net/usb/usbnet.c
include/linux/usb/usbnet.h
net/ipv4/tcp_ipv4.c
net/ipv6/tcp_ipv6.c
The TCP conflicts were overlapping changes. In 'net' we added a
READ_ONCE() to the socket cached RX route read, whilst in 'net-next'
Eric Dumazet touched the surrounding code dealing with how mini
sockets are handled.
With USB, it's a case of the same bug fix first going into net-next
and then I cherry picked it back into net.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new Common Code routines to retrieve Firmware Device Log
parameters from PCIE_FW_PF[7]. The firmware initializes its Device Log very
early on and stores the parameters for its location/size in that register.
Using the parameters from the register allows us to access the Firmware
Device Log even when the firmware crashes very early on or we're not
attached to the firmware
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds new macro and few macro changes for fw version 1.13.32.0 also
changes version string in driver to match 1.13.32.0
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move ~2KB of strings in each driver from data to text.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes sparse warnings introduced in commit e85c9a7abf ("cxgb4/cxgb4vf: Add
code to calculate T5 BAR2 Offsets for SGE Queue Registers") and
df64e4d38c ("cxgb4/cxgb4vf: Use new interfaces to calculate BAR2 SGE Queue
Register addresses") and few old ones
sparse warnings:
>> drivers/net/ethernet/chelsio/cxgb4vf/sge.c:1006:48: sparse: cast removes
>> address space of expression
>> drivers/net/ethernet/chelsio/cxgb4vf/sge.c:1006:48: sparse: incorrect type in
>> initializer (different address space)
>> drivers/net/ethernet/chelsio/cxgb4vf/sge.c:1020:40: sparse: incorrect type in
>> argument 1 (different base types)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable interrupts and quiesce rx before unregistering net device to avoid crash
while unloading driver when traffic is flowing through.
Based on original work by Shameem Khalid <shameem@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
QIDs (egress/ingress) from firmware in FW_*_CMD.alloc command
can be anywhere in the range from EQ(IQFLINT)_START to EQ(IQFLINT)_END.
For eg, in the first load eqid can be from 100 to 300.
In the next load it can be from 301 to 500 (assume eq_start is 100 and eq_end is
1000).
The driver was assuming them to always start from EQ(IQFLINT)_START till
MAX_EGRQ(INGQ). This was causing stack overflow and subsequent crash.
Fixed it by dynamically allocating memory (of qsize (x_END - x_START + 1)) for
these structures.
Based on original work by Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/chelsio/cxgb4/cxgb4_fcoe.c:49:9-10: WARNING: return of 0/1 in function 'cxgb_fcoe_sof_eof_supported' with return type bool
Return statements in functions returning bool should use
true/false instead of 1/0.
Generated by: scripts/coccinelle/misc/boolreturn.cocci
CC: Varun Prakash <varun@chelsio.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes below warning by dynamically allocating memory
All warnings:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_debugfs.c: In function
'cctrl_tbl_show':
>> drivers/net/ethernet/chelsio/cxgb4/cxgb4_debugfs.c:689:1: warning: the
>> frame
>> size of 1028 bytes is larger than 1024 bytes [-Wframe-larger-than=]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds cxgb4_fcoe.c and enables FCOE_CRC, FCOE_MTU
net device features.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds new header file cxgb4_fcoe.h and defines new
macros for FCoE support in cxgb4 driver.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
net/core/sysctl_net_core.c
net/ipv4/inet_diag.c
The be_main.c conflict resolution was really tricky. The conflict
hunks generated by GIT were very unhelpful, to say the least. It
split functions in half and moved them around, when the real actual
conflict only existed solely inside of one function, that being
be_map_pci_bars().
So instead, to resolve this, I checked out be_main.c from the top
of net-next, then I applied the be_main.c changes from 'net' since
the last time I merged. And this worked beautifully.
The inet_diag.c and sysctl_net_core.c conflicts were simple
overlapping changes, and were easily to resolve.
Signed-off-by: David S. Miller <davem@davemloft.net>
Make PCI Device ID Tables be "const" to move them out of the data segment and
remove a redundant check on CH_PCI_DEVICE_ID_TABLE_DEFINE_BEGIN in
t4_pci_id_tbl.h to guard the contents of the include file.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To test a checkpatch spelling patch, I ran codespell against
drivers/net/ethernet/.
$ git ls-files drivers/net/ethernet/ | \
while read file ; do \
codespell -w $file; \
done
I removed a false positive in e1000_hw.h
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To allow for better scalability on systems with large core counts, we
will try and allocate enough RDMA Concentrator IQs and MSI/X vectors as
we have cores. If we cannot get enough MSI/X vectors, fall back to the
minimum required: 1 per adapter rx channel.
Also clean up cxgb_enable_msix() to make it readable and correct a bug
where the vectors are not correctly assigned if the driver doesn't get
the full amount requested.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds a common function for all Rx queue allocation.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing reads and writes to adapter memory via the PCI-E Memory Window
interface, data gets swizzled on 4-byte boundaries on Big-Endian systems
because we need to account for the register read/write interface which
incorporates a swizzle onto the Little-Endian PCI-E Bus.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Issue caught by 0-day kernel test infrastructure. Code changed to use sockaddr
members so that %pISc can be used instead.
Fixes: b5a02f503c ('cxgb4 : Update ipv6 address handling api')
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull debugfs patches from Al Viro:
"debugfs patches, mostly to make it possible for something like tracefs
to be transparently automounted on given directory in debugfs.
New primitive in there is debugfs_create_automount(name, parent, func,
arg), which creates a directory and makes its ->d_automount() return
func(arg). Another missing primitive was debugfs_create_file_size() -
open-coded in quite a few places. Dave's patch adds it and converts
the open-code instances to calling it"
* 'debugfs_automount' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
debugfs: Provide a file creation function that also takes an initial size
new primitive: debugfs_create_automount()
debugfs: split end_creating() into success and failure cases
debugfs: take mode-dependent parts of debugfs_get_inode() into callers
fold debugfs_mknod() into callers
fold debugfs_create() into caller
fold debugfs_mkdir() into caller
debugfs_mknod(): get rid useless arguments
fold debugfs_link() into caller
debugfs: kill __create_file()
debugfs: split the beginning and the end of __create_file() off
debugfs_{mkdir,create,link}(): get rid of redundant argument
Pull misc VFS updates from Al Viro:
"This cycle a lot of stuff sits on topical branches, so I'll be sending
more or less one pull request per branch.
This is the first pile; more to follow in a few. In this one are
several misc commits from early in the cycle (before I went for
separate branches), plus the rework of mntput/dput ordering on umount,
switching to use of fs_pin instead of convoluted games in
namespace_unlock()"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
switch the IO-triggering parts of umount to fs_pin
new fs_pin killing logics
allow attaching fs_pin to a group not associated with some superblock
get rid of the second argument of acct_kill()
take count and rcu_head out of fs_pin
dcache: let the dentry count go down to zero without taking d_lock
pull bumping refcount into ->kill()
kill pin_put()
mode_t whack-a-mole: chelsio
file->f_path.dentry is pinned down for as long as the file is open...
get rid of lustre_dump_dentry()
gut proc_register() a bit
kill d_validate()
ncpfs: get rid of d_validate() nonsense
selinuxfs: don't open-code d_genocide()
Provide a file creation function that also takes an initial size so that the
caller doesn't have to set i_size, thus meaning that we don't have to call
deal with ->d_inode in the callers.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add support to get option/expansion rom version flashed in the adapter via
ethtool getdrvinfo function.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ganesh Goudar