Patch tpm-correct-tpm-timeouts-to-jiffies-conversion reveals a bug in the
Broadcom BCM0102 TPM chipset used in the Dell Latitude D820 - although
most of the timeouts are returned in usecs as per the spec, one is
apparently returned in msecs, which results in a too-small value leading
to a timeout when the code treats it as usecs. To prevent a regression,
we check for the known too-short value and adjust it to a value that makes
things work.
Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Cc: Marcin Obara <marcin_obara@users.sourceforge.net>
Cc: Marcel Selhorst <tpm@selhorst.net>
Cc: Kylene Jo Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes timeouts conversion to jiffies, by replacing
msecs_to_jiffies() calls with usecs_to_jiffies(). According to TCG TPM
Specification Version 1.2 Revision 103 (pages 166, 167) TPM timeouts and
durations are returned in microseconds (usec) not in miliseconds (msec).
This fixes a long hang while loading TPM driver, if TPM chip starts in
"Idle" state instead of "Ready" state. Without this patch - 'modprobe'
may hang for 30 seconds or more.
Signed-off-by: Marcin Obara <marcin_obara@users.sourceforge.net>
Cc: Marcel Selhorst <tpm@selhorst.net>
Cc: Kylene Jo Hall <kjhall@us.ibm.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
name and nlen parameters passed to ->strategy hook are unused, remove
them. In general ->strategy hook should know what it's doing, and don't
do something tricky for which, say, pointer to original userspace array
may be needed (name).
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net> [ networking bits ]
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move it into sysrq.c, along with the rest of the sysrq implementation.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The only use is to pass this to le16_to_cpu, declare as such
drivers/char/moxa.c:548:11: warning: cast to restricted __le16.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The code scriblles over a local pointer whereas it appears to be trying
to write to the memory at which that pointer points.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=11397
Nobody we know can test this change.
Reported-by: Zvonimir Rakamaric <zrakamar@cs.ubc.ca>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ds1286_get_time(); is not called from atomic context, sleep for 20 ms is
better choice than a (home-made) busy waiting for such a situation.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
HPET_RTC_IRQ is no longer needed; HPET_EMULATE_RTC suffices and is more
correct. (http://bugzilla.kernel.org/show_bug.cgi?id=11111)
Note that when using the legacy RTC driver, platforms don't really do a
dynamic switch between HPET and non-HPET modes based on whether HPET
hardware actually exists ... only rtc-cmos (using the new RTC framework)
currently switches that way.
So this reflects bitrot in that legacy code, for x86/ia64: kernels with
HPET support configured (e.g. for a clocksource) can't get IRQs from the
legacy RTC driver unless they really have HPET hardware. (The obvious
workaround is to not use the legacy RTC driver on those platforms when you
configure HPET ... unless you know the target really has a HPET.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
People can use the real name an an index into MAINTAINERS to find the
current email address.
Signed-off-by: Francois Cami <francois.cami@free.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is written in the Documentation/sysrq.txt that oom-killer is enabled
when we set "64" in /proc/sys/kernel/sysrq:
<Documentation/sysrq.txt>
Here is the list of possible values in /proc/sys/kernel/sysrq:
64 - enable signalling of processes (term, kill, oom-kill)
^^^^^^^^
but enable_mask is not set in sysrq_moom_op.
Signed-off-by: Naohiro Ooiwa <nooiwa@miraclelinux.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This code is not ready, but we need to rip it out instead of rebasing
as we would lose the APIC/IO_APIC unification otherwise.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
irq_timer_state[] is a NR_IRQS sized array that is a side-by array to
the real irq_desc[] array.
Integrate that field into the (now dynamic) irq_desc dynamic array and
save some RAM.
v2: keep the old way to support arch not support irq_desc
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Reinitialize bridge registers after suspend, but avoid repeating the ioremap
Tested and works on AMD761
Signed-off-by: Stuart Bennett <stuart@freedesktop.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Instead of doing a posting read after each GTT entry update, do a single one
at the end of the writes. This should reduce boot time a tiny amount by
avoiding a lot of extra uncached reads.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On the GM45, the amount of stolen memory mapped to the GTT was underestimated,
even though we had 508KB more available since the GTT doesn't take from
stolen memory. On the non-GM45 G4X, we overestimated how much stolen was
mapped to the GTT by 4KB, resulting in GPU page faults when that page was
accessed.
This update requires a corresponding update to xf86-video-intel to work
correctly.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
proc_clear_tty() gets called with interrupts off (while holding the task list
lock) from sys_setid. This means that it needs the _irqsave version of the
locking primitives.
Reported-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Tested-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit 611e097d77
Author: Christian Borntraeger <borntraeger@de.ibm.com>
hvc_console: rework setup to replace irq functions with callbacks
introduced a spinlock recursion problem. The notifier_del is
called with a lock held, and in turns calls free_irq which then
complains when manipulating procfs. This fixes it by moving the
call to the notifier to outside of the locked section.
Signed-off-by: Christian Borntraeger<borntraeger@de.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This reverts commit c9e587abfd, and the
subsequent commits that fixed it up:
- afa9b649 "fbcon: prevent cursor disappearance after switching to 512
character font"
- d850a2fa "vt/fbcon: fix background color on line feed"
- 7fe3915a "vt/fbcon: update scrl_erase_char after 256/512-glyph font
switch"
by request of Alan Cox. Quoth Alan:
"Unfortunately it's wrong and its been causing breakages because
various apps like ncurses expect our previous (and correct)
behaviour."
Alexander sent out a similar patch.
Requested-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Tested-by: Jan Engelhardt <jengelh@medozas.de>
Cc: Alexander V. Lukyanov <lav@netis.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6: (24 commits)
integrity: special fs magic
As pointed out by Jonathan Corbet, the timer must be deleted before
ERROR: code indent should use tabs where possible
The tpm_dev_release function is only called for platform devices, not pnp
Protect tpm_chip_list when transversing it.
Renames num_open to is_open, as only one process can open the file at a time.
Remove the BKL calls from the TPM driver, which were added in the overall
netlabel: Add configuration support for local labeling
cipso: Add support for native local labeling and fixup mapping names
netlabel: Changes to the NetLabel security attributes to allow LSMs to pass full contexts
selinux: Cache NetLabel secattrs in the socket's security struct
selinux: Set socket NetLabel based on connection endpoint
netlabel: Add functionality to set the security attributes of a packet
netlabel: Add network address selectors to the NetLabel/LSM domain mapping
netlabel: Add a generic way to create ordered linked lists of network addrs
netlabel: Replace protocol/NetLabel linking with refrerence counts
smack: Fix missing calls to netlbl_skbuff_err()
selinux: Fix missing calls to netlbl_skbuff_err()
selinux: Fix a problem in security_netlbl_sid_to_secattr()
selinux: Better local/forward check in selinux_ip_postroute()
...
Merges oprofile, timers/hpet, x86/traps, x86/time, and x86/core misc items.
* 'x86-core-v4-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (132 commits)
x86: change early_ioremap to use slots instead of nesting
x86: adjust dependencies for CONFIG_X86_CMOV
dumpstack: x86: various small unification steps, fix
x86: remove additional_cpus
x86: remove additional_cpus configurability
x86: improve UP kernel when CPU-hotplug and SMP is enabled
dumpstack: x86: various small unification steps
dumpstack: i386: make kstack= an early boot-param and add oops=panic
dumpstack: x86: use log_lvl and unify trace formatting
dumptrace: x86: consistently include loglevel, print stack switch
dumpstack: x86: add "end" parameter to valid_stack_ptr and print_context_stack
dumpstack: x86: make printk_address equal
dumpstack: x86: move die_nmi to dumpstack_32.c
traps: x86: finalize unification of traps.c
traps: x86: make traps_32.c and traps_64.c equal
traps: x86: various noop-changes preparing for unification of traps_xx.c
traps: x86_64: use task_pid_nr(tsk) instead of tsk->pid in do_general_protection
traps: i386: expand clear_mem_error and remove from mach_traps.h
traps: x86_64: make io_check_error equal to the one on i386
traps: i386: use preempt_conditional_sti/cli in do_int3
...
Original idea for this from a patch by Rodolfo Giometti which merges various
bits of PPS support
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/char/tty_io.c:1413:17: warning: symbol 'buf' shadows an earlier one
drivers/char/tty_io.c:1379:20: originally declared here
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Closes bug #11408 by checking the card index range for command 0
Fixes the ioctl to return ENOTTY which is correct for unknown ioctls
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many tty drivers contain 'can't happen' checks against NULL pointers passed
in by the tty layer. These have never been possible to occur. Even more
importantly if they ever do occur we want to know as it would be a serious
bug.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the set up on ldisc change into the ldisc
Move the INQ/OUTQ cases into the driver not in shared ioctl code where it
gives bogus answers for other ldisc values
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Copy the simplification from the pty unix98 special case to the generic one.
This allows us to kill off driver->termios_locked entirely which is nice. We
have to whack bits of the cris driver as it meddles in places it shouldn't
providing its own arrays that were never used anyway.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We need both termios and termios_locked so allocate them as one
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The updating and moving around of the pty code added a bug where both the
helper and caller free the main tty struct (the pty driver must free the
o_tty pair itself however).
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We've done the heavy lifting now its time to mop up a bit
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pass-in 'inode' or 'tty' parameter to devpts interfaces. With multiple
devpts instances, these parameters will be used in subsequent patches
to identify the instance of devpts mounted. The parameters also help
simplify devpts implementation.
Changelog[v3]:
- minor changes due to merge with ttydev updates
- rename parameters to emphasize they are ptmx or pts inodes
- pass-in tty_struct * to devpts_pty_kill() (this will help
cleanup the get_node() call in a subsequent patch)
Signed-off-by: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move tty_driver_lookup_tty() and tty_reopen() from tty_init_dev()
into tty_open() (one of the two callers of tty_init_dev()). These
calls are not really required in ptmx_open(), the other caller,
since ptmx_open() would be setting up a new tty.
Changelog[v2]:
- remove the lookup and reopen calls from ptmx_open
- merge with recent changes to ttydev tree
Signed-off-by: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The majority of the remaining init_dev code is pty special cases. We
refactor this code into the driver->install method.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Original suggestion and proposal from Sukadev Bhattiprolu.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have the lookup operation abstracted which is nice for pty cleanup but
we really want to abstract the add/remove entries as well so that we can
pull the pty code out of the tty core and create a clear defined interface
for the tty driver table.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix up the naming, style and extract some bits of code into the driver
specific code
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the 'find-tty' and 'fast-track-open' parts of init_dev() to
separate functions.
Signed-off-by: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Carry on pushing code out of tty_io when it belongs to other drivers. I'm
not 100% happy with some of this and it will be worth revisiting some of the
exports later when the restructuring work is done.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Right now there are various drivers that try to use tty->count to know when
they get the final close. Aristeau Rozanski showed while debugging the vt
sysfs race that this isn't entirely safe.
Instead of driver side tricks to work around this introduce a shutdown which
is called when the tty is being destructed. This also means that the shutdown
method is tied into the refcounting.
Use this to rework the console close/sysfs logic.
Remove lots of special case code from the tty core code. The pty code can now
have a shutdown() method that replaces the special case hackery in the tree
free up paths.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For hysterical raisins the vt layer drops and retakes locks in the write
method. This is a left over from the days when user/kernel data was passed
directly to the tty not pre-buffered.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The open path for ptmx slaves is via the ptmx device. Opening them any
other way is not allowed. Vegard Nossum found that previously this was not
the case and mknod foo c 128 42; cat foo would produce nasty diagnostics
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently it is sometimes locked by the tty mutex and sometimes by the
sighand lock. The latter is in fact correct and now we can hand back referenced
objects we can fix this up without problems around sleeping functions.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We now have the infrastructure to sort this out but rather than teaching
the syscall tty lock rules we move the hard work into a tty helper
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use tty_port_init and krefs in the stallion drivers to protect us from devices
going away underneath us. As with the other drives some rearranging is done to
pass the tty structure down properly on the user side.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rather than blindly keep taking krefs we reorder the code in a few places
to pass the tty down to the right place (which is important as from the user
side it is not the case that tty == port->tty in all situations). For the irq
and related paths use the krefs to stop the tty being freed under us.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use kref in the USB serial drivers so that we don't free tty structures
from under the URB receive handlers as has historically been the case if
you were unlucky. This also gives us a framework for general tty drivers to
use tty_port objects and refcount.
Contains two err->dev_err changes merged together to fix clashes in the
-next tree.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is pure tty code so put it in the tty layer where it can be with the
locking relevant material it uses
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We now return a kref covered tty reference. That ensures the tty structure
doesn't go away when you have a return from get_current_tty. This is not
enough to protect you from most of the resources being freed behind your
back - yet.
[Updated to include fixes for SELinux problems found by Andrew Morton and
an s390 leak found while debugging the former]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We always use the real tty one for stuff so the pty one should not be
compared. As we propagate window changes to both it doesn't currently
matter but will when we tidy up the pty termios logic a bit more
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This moves us towards sanity and should mean our termios locking is now
complete and comprehensive.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We need a way to describe the various additional modes and flow control
features that random weird hardware shows up and software such as wine
wants to emulate as Windows supports them.
TCGETX/TCSETX and the termiox ioctl are a SYS5 extension that we might as
well adopt. This patches adds the structures and the basic ioctl interfaces
when the TCGETX etc defines are added for an architecture. Drivers wishing
to use this stuff need to add new methods.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This came in via another tree and unfortunately is rather broken on
the tty side. Comment the apparent locking problems for someone who knows
the driver to look at.
Fix the termios and other ioctl handling. The driver was calling the wrong
methods for what it wanted to do but the right ones existed so its a simple
fix up.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The tty layer keeps driver module counts that are used so the driver knows
when it can be unloaded. For obvious reasons we want to tie that to the
refcounting properly.
At this point the driver side itself isn't refcounted nicely but we can do
that later and kref the drivers.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce a kref to the tty structure and use it to protect the tty->signal
tty references. For now we don't introduce it for anything else.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The two are basically independent chunks of code so lets split them up for
readability and sanity. It also makes the API boundaries much clearer.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Right now we have ifdefs and hooks in the core ioctl handler for TIOCLINUX
and then test if its a console. This is brain dead. Instead call the
tioclinux helper from the relevant driver ioctl methods.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nozomi assumes the close method isn't called if open errors. The tty layer
is different to other drives in this respect however. Pointed out by Denis J
Barrow.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Data read from a TTY can contain an embedded NUL byte (e.g. after
pressing Ctrl-2, or sent to a PTY). After the previous patch, the data
would be logged only up to the first NUL.
This patch modifies the AUDIT_TTY record to always use the hexadecimal
format, which does not terminate at the first NUL byte. The vast
majority of recorded TTY input data will contain either ' ' or '\n', so
the hexadecimal format would have been used anyway.
Signed-off-by: Miloslav Trmac <mitr@redhat.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
add_timer() is not supposed to be called when the timer is pending.
ip2 driver attempts to avoid that condition by setting and resetting
a flag (TimerOn) in timer function. But there is some gap between
add_timer() and setting TimerOn.
This patch fix this problem by using mod_timer() and remove TimerOn
which has been unnecessary by this change.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cleanup of module_init/exit:
- mostly whitespace
- remove empty functions
- replace c++ comments
- remove useless prints (module loaded, unloaded)
- mark the calls as __exit and __init
- use break; and return; to save some indent levels after it
- note resource leakage
It's still mess, but now it's readable.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- do not init .bss zeroed data to zero again (by memset or
explicit assignment)
- use char [] instead of char * for string constants
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It's pretty useless to have one setup() function separated along with
module_init() which only calls a function from ip2main anyway. Get rid
of ip2base.
Remove also checks of always-true now.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
board->base is increased for CF cards after mapping. Use board->base2
for unmapping the region, since it holds the original/correct address.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
readl/writel are not expected to accept iomap return value. Replace
bogus mapping by standard ioremap.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The call to put_tty_driver is out of place and is applied to the wrong
argument.
The function enclosing the patched code calls alloc_tty_driver and stores
the result in drv. Subsequently, there are two occurrences of error
handling code, one making a goto to put_tty and one making a goto to
stop_thread. At the point of the first one the assignment hvc_driver = drv
has not yet been executed, and from inspecting the rest of the file it
seems that hvc_driver would be NULL. Thus the current call to
put_tty_driver is useless, and one applied to drv is needed. The goto
stop_thread is in the error handling code for a call to
tty_register_driver, but the error cases in tty_register_driver do not free
its argument, so it should be done here. Thus, I have moved the put_tty
label after the stop_thread label, so that put_tty_driver is called in both
cases.
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
expression E,f;
position p1,p2,p3;
identifier l;
statement S;
@@
x = alloc_tty_driver@p1(...)
...
if (x == NULL) S
... when != E = x
when != put_tty_driver(x)
goto@p2 l;
... when != E = x
when != f(...,x,...)
when any
(
return \(0\|x\);
|
return@p3 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
p3 << r.p3;
@@
print "%s: call on line %s not freed or saved before return on line %s via line %s" % (p1[0].file,p1[0].line,p3[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This merges in:
x86/build, x86/microcode, x86/spinlocks, x86/memory-corruption-check,
x86/early-printk, x86/xsave, x86/quirks, x86/setup, x86/signal,
core/signal, x86/urgent, x86/xen
* 'x86-core-v2-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (142 commits)
x86: make processor type select depend on CONFIG_EMBEDDED
x86: extend processor type select help text
x86, amd-iommu: propagate PCI device enabling error
warnings: fix arch/x86/kernel/io_apic_64.c
warnings: fix arch/x86/kernel/early_printk.c
x86, fpu: check __clear_user() return value
x86: memory corruption check - cleanup
x86: ioperm user_regset
xen: do not reserve 2 pages of padding between hypervisor and fixmap.
xen: use spin_lock_nest_lock when pinning a pagetable
x86: xsave: set FP, SSE bits in the xsave header in the user sigcontext
x86: xsave: fix error condition in save_i387_xstate()
x86: SB450: deprioritize DMI quirks
x86: SB450: skip IRQ0 override if it is not routed to INT2 of IOAPIC
x86: replace a magic number with a named constant in the VESA boot code
x86 setup: remove IMAGE_OFFSET
x86 setup: remove DEF_INITSEG and DEF_SETUPSEG
Revert "x86: fix ghost EDD devices in /sys again"
x86 setup: fix ghost entries under /sys/firmware/edd take 3
x86: signal: remove indent in restore_sigcontext()
...
* 'x86-v28-for-linus-phase2-B' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (27 commits)
x86, cpa: make the kernel physical mapping initialization a two pass sequence, fix
x86, pat: cleanups
x86: fix pagetable init 64-bit breakage
x86: track memtype for RAM in page struct
x86, cpa: srlz cpa(), global flush tlb after splitting big page and before doing cpa
x86, cpa: remove cpa pool code
x86, cpa: no need to check alias for __set_pages_p/__set_pages_np
x86, cpa: dont use large pages for kernel identity mapping with DEBUG_PAGEALLOC
x86, cpa: make the kernel physical mapping initialization a two pass sequence
x86, cpa: remove USER permission from the very early identity mapping attribute
x86, cpa: rename PTE attribute macros for kernel direct mapping in early boot
x86: make sure the CPA test code's use of _PAGE_UNUSED1 is obvious
linux-next: fix x86 tree build failure
x86: have set_memory_array_{uc,wb} coalesce memtypes, fix
agp: enable optimized agp_alloc_pages methods
x86: have set_memory_array_{uc,wb} coalesce memtypes.
x86: {reverve,free}_memtype() take a physical address
x86: fix pageattr-test
agp: add agp_generic_destroy_pages()
agp: generic_alloc_pages()
...
flushing the work queue in order to avoid a job being submitted after the
chip had been released.
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: "Serge E. Hallyn" <serue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Morris <jmorris@namei.org>
devices, so we implemented the .remove function for pnp ones. Since it's
code is very similar to the one inside tpm_dev_release, we've created a
helper function tpm_dev_vendor_release, which is called by both.
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Cc: "Serge E. Hallyn" <serue@us.ibm.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Morris <jmorris@namei.org>
misc-char-dev-BKL-pushdown.patch, as they are not needed.
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Cc: "Serge E. Hallyn" <serue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Morris <jmorris@namei.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
selinux: Fix an uninitialized variable BUG/panic in selinux_secattr_to_sid()
selinux: use default proc sid on symlinks
file capabilities: uninline cap_safe_nice
Update selinux info in MAINTAINERS and Kconfig help text
SELinux: add gitignore file for mdp script
SELinux: add boundary support and thread context assignment
securityfs: do not depend on CONFIG_SECURITY
selinux: add support for installing a dummy policy (v2)
security: add/fix security kernel-doc
selinux: Unify for- and while-loop style
selinux: conditional expression type validation was off-by-one
smack: limit privilege by label
SELinux: Fix a potentially uninitialised variable in SELinux hooks
SELinux: trivial, remove unneeded local variable
SELinux: Trivial minor fixes that change C null character style
make selinux_write_opts() static
On x86 systems with CONFIG_HPET_TIMER enabled, when
the HPET driver (drivers/char/hpet.c) is loaded,
an incorrect busy message is printed when the driver
initializes since the HPET has already been allocated
by the core timer code. Remove the warning message.
Signed-off-by: David John <davidjon@xenontk.org>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* Implement disk_devt() and part_devt() and use them to directly
access devt instead of computing it from ->major and ->first_minor.
Note that all references to ->major and ->first_minor outside of
block layer is used to determine devt of the disk (the part0) and as
->major and ->first_minor will continue to represent devt for the
disk, converting these users aren't strictly necessary. However,
convert them for consistency.
* Implement disk_max_parts() to avoid directly deferencing
genhd->minors.
* Update bdget_disk() such that it doesn't assume consecutive minor
space.
* Move devt computation from register_disk() to add_disk() and make it
the only one (all other usages use the initially determined value).
These changes clean up the code and will help disk->part dereference
fix and extended block device numbers.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The tty_find_polling_driver() routine did not correctly check the base
part of the tty name. This can lead to kgdboc selecting an incorrect
driver, as well as accepting a completely invalid tty such as "echo
ffff0 > /sys/module/kgdboc/parameters/kgdboc".
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Now that arch/ppc is dead CONFIG_PPC_MERGE is always defined for all
powerpc platforms and we want to get rid of CONFIG_PPC_MERGE use
CONFIG_PPC instead.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix a bug reported by and diagnosed by Aaron Straus.
This is a regression intruduced into 2.6.26 by
commit adc782dae6
Author: Matt Mackall <mpm@selenic.com>
Date: Tue Apr 29 01:03:07 2008 -0700
random: simplify and rename credit_entropy_store
credit_entropy_bits() does:
spin_lock_irqsave(&r->lock, flags);
...
if (r->entropy_count > r->poolinfo->POOLBITS)
r->entropy_count = r->poolinfo->POOLBITS;
so there is a time window in which this BUG_ON():
static size_t account(struct entropy_store *r, size_t nbytes, int min,
int reserved)
{
unsigned long flags;
BUG_ON(r->entropy_count > r->poolinfo->POOLBITS);
/* Hold lock while accounting */
spin_lock_irqsave(&r->lock, flags);
can trigger.
We could fix this by moving the assertion inside the lock, but it seems
safer and saner to revert to the old behaviour wherein
entropy_store.entropy_count at no time exceeds
entropy_store.poolinfo->POOLBITS.
Reported-by: Aaron Straus <aaron@merfinllc.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: <stable@kernel.org> [2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since we're just parsing the tuple being passed to this function, we don't
need any device-specific information.
Also, remove the call to pcmcia_validate_cis() from pcmciamtd.c, since it
is already called by the PCMCIA core.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
16-bit PCMCIA device handling function definitions are moved to ds.h,
internal definitions to cs_internal.h.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Add a new Kconfig option SECURITYFS which will build securityfs support
but does not require CONFIG_SECURITY. The only current user of
securityfs does not depend on CONFIG_SECURITY and there is no reason the
full LSM needs to be built to build this fs.
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
Kanru Chen posted a patch versus the old code which deals with the case
where you resize the pty side of a pty/tty pair. In that situation the
termios data is updated for both pty and tty but the locks are not held
for the right side.
This implements the fix differently against the updated tty code. Patch
by self but the hard bit (noticing and fixing the bug) is thanks to Kanru
Chen.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The termios settings ioctls on a pty should affect the bound tty side not
the pty. The SOFTCAR ioctls use the wrong device file.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch lets the files using linux/version.h match the files that
#include it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Instead of using own error or success codes, the PCMCIA code should rely on
the generic return values. Therefore, replace all occurrences of CS_SUCCESS
with 0.
CC: netdev@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Remove the three remaining pcmcia_get_configuration_info() users:
- pcmciamtd is marked broken anyway.
- serial_cs.c can access the relevant structs directly
- ipwireless didn't use the output
CC: linux-serial@vger.kernel.org
CC: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
By passing the current Vcc setting to the pcmcia_config_loop callback
function, we can remove pcmcia_get_configuration_info() calls from many
drivers.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Many drivers use the default CIS entry within their pcmcia_config_loop()
callback function. Therefore, factor the default CIS entry handling out.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Almost all drivers set p_dev->conf.ConfigIndex to cfg->index in
the pcmcia_config_loop() callback function. Therefore, factor it out.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Use the config loop helper in misc pcmcia drivers.
CC: Harald Welte <laforge@gnumonks.org>
CC: <linux-parport@lists.infradead.org>
CC: Russell King <rmk+kernel@arm.linux.org.uk>
CC: Ed Okerson <eokerson@quicknet.net>
CC: linux-serial@vger.kernel.org
CC: boti@rocketmail.com
CC: linux-usb@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The pageattr-array patch that you currently have in tip/master only
enables it for intel-agp, not the others. The attached enables it for
all drivers currently directly using agp_generic_alloc_page() and
agp_generic_destroy_page() (ocal driver is amd-k7-agp).
The new agp_generic_alloc_pages() interface uses the also new
pageattr array interface API. This makes all AGP drivers that
up to now used generic_{alloc,destroy}_page() use it.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There are four operating modes Xen code may find itself running in:
- native
- hvm domain
- pv dom0
- pv domU
Clean up predicates for testing for these states to make them more consistent.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Xen-devel <xen-devel@lists.xensource.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (94 commits)
pkt_sched: Prevent livelock in TX queue running.
Revert "pkt_sched: Add BH protection for qdisc_stab_lock."
Revert "pkt_sched: Protect gen estimators under est_lock."
pkt_sched: remove bogus block (cleanup)
nf_nat: use secure_ipv4_port_ephemeral() for NAT port randomization
netfilter: ctnetlink: sleepable allocation with spin lock bh
netfilter: ctnetlink: fix sleep in read-side lock section
netfilter: ctnetlink: fix double helper assignation for NAT'ed conntracks
netfilter: ipt_addrtype: Fix matching of inverted destination address type
dccp: Fix panic caused by too early termination of retransmission mechanism
pkt_sched: Don't hold qdisc lock over qdisc_destroy().
pkt_sched: Add lockdep annotation for qdisc locks
pkt_sched: Never schedule non-root qdiscs.
removed unused #include <version.h>
rt2x00: Fix txdone_entry_desc_flags
b43: Fix for another Bluetooth Coexistence SPROM Programming error for BCM4306
mac80211: remove kdoc references to IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE
p54u: reset skb's data/tail pointer on requeue
p54: move p54_vdcf_init to the right place.
iwlwifi: fix printk newlines
...
Use incoming network tuple as seed for NAT port randomization.
This avoids concerns of leaking net_random() bits, and also gives better
port distribution. Don't have NAT server, compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
[ added missing EXPORT_SYMBOL_GPL ]
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The drivers below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
drivers/char/pcmcia/ipwireless/tty.c
drivers/char/synclink_gt.c
drivers/char/xilinx_hwicap/xilinx_hwicap.c
This patch removes the said #include <version.h>.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This moves it to being a tty operation. That removes special cases and now
also means that resize can be picked up by um and other non vt consoles
which may have a resize operation.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To reduce tlb/cache flush, makes agp memory allocation do one flush
after all pages in a region are changed to uc.
All agp drivers except agp-sgi uses agp_generic_alloc_page()
for .agp_alloc_page, so the patch should work for them. agp-sgi is only
for ia64, so not a problem too.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Cc: airlied@linux.ie
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Wolfgang Walter reported this oops on his via C3 using padlock for
AES-encryption:
##################################################################
BUG: unable to handle kernel NULL pointer dereference at 000001f0
IP: [<c01028c5>] __switch_to+0x30/0x117
*pde = 00000000
Oops: 0002 [#1] PREEMPT
Modules linked in:
Pid: 2071, comm: sleep Not tainted (2.6.26 #11)
EIP: 0060:[<c01028c5>] EFLAGS: 00010002 CPU: 0
EIP is at __switch_to+0x30/0x117
EAX: 00000000 EBX: c0493300 ECX: dc48dd00 EDX: c0493300
ESI: dc48dd00 EDI: c0493530 EBP: c04cff8c ESP: c04cff7c
DS: 007b ES: 007b FS: 0000 GS: 0033 SS: 0068
Process sleep (pid: 2071, ti=c04ce000 task=dc48dd00 task.ti=d2fe6000)
Stack: dc48df30 c0493300 00000000 00000000 d2fe7f44 c03b5b43 c04cffc8 00000046
c0131856 0000005a dc472d3c c0493300 c0493470 d983ae00 00002696 00000000
c0239f54 00000000 c04c4000 c04cffd8 c01025fe c04f3740 00049800 c04cffe0
Call Trace:
[<c03b5b43>] ? schedule+0x285/0x2ff
[<c0131856>] ? pm_qos_requirement+0x3c/0x53
[<c0239f54>] ? acpi_processor_idle+0x0/0x434
[<c01025fe>] ? cpu_idle+0x73/0x7f
[<c03a4dcd>] ? rest_init+0x61/0x63
=======================
Wolfgang also found out that adding kernel_fpu_begin() and kernel_fpu_end()
around the padlock instructions fix the oops.
Suresh wrote:
These padlock instructions though don't use/touch SSE registers, but it behaves
similar to other SSE instructions. For example, it might cause DNA faults
when cr0.ts is set. While this is a spurious DNA trap, it might cause
oops with the recent fpu code changes.
This is the code sequence that is probably causing this problem:
a) new app is getting exec'd and it is somewhere in between
start_thread() and flush_old_exec() in the load_xyz_binary()
b) At pont "a", task's fpu state (like TS_USEDFPU, used_math() etc) is
cleared.
c) Now we get an interrupt/softirq which starts using these encrypt/decrypt
routines in the network stack. This generates a math fault (as
cr0.ts is '1') which sets TS_USEDFPU and restores the math that is
in the task's xstate.
d) Return to exec code path, which does start_thread() which does
free_thread_xstate() and sets xstate pointer to NULL while
the TS_USEDFPU is still set.
e) At the next context switch from the new exec'd task to another task,
we have a scenarios where TS_USEDFPU is set but xstate pointer is null.
This can cause an oops during unlazy_fpu() in __switch_to()
Now:
1) This should happen with or with out pre-emption. Viro also encountered
similar problem with out CONFIG_PREEMPT.
2) kernel_fpu_begin() and kernel_fpu_end() will fix this problem, because
kernel_fpu_begin() will manually do a clts() and won't run in to the
situation of setting TS_USEDFPU in step "c" above.
3) This was working before the fpu changes, because its a spurious
math fault which doesn't corrupt any fpu/sse registers and the task's
math state was always in an allocated state.
With out the recent lazy fpu allocation changes, while we don't see oops,
there is a possible race still present in older kernels(for example,
while kernel is using kernel_fpu_begin() in some optimized clear/copy
page and an interrupt/softirq happens which uses these padlock
instructions generating DNA fault).
This is the failing scenario that existed even before the lazy fpu allocation
changes:
0. CPU's TS flag is set
1. kernel using FPU in some optimized copy routine and while doing
kernel_fpu_begin() takes an interrupt just before doing clts()
2. Takes an interrupt and ipsec uses padlock instruction. And we
take a DNA fault as TS flag is still set.
3. We handle the DNA fault and set TS_USEDFPU and clear cr0.ts
4. We complete the padlock routine
5. Go back to step-1, which resumes clts() in kernel_fpu_begin(), finishes
the optimized copy routine and does kernel_fpu_end(). At this point,
we have cr0.ts again set to '1' but the task's TS_USEFPU is stilll
set and not cleared.
6. Now kernel resumes its user operation. And at the next context
switch, kernel sees it has do a FP save as TS_USEDFPU is still set
and then will do a unlazy_fpu() in __switch_to(). unlazy_fpu()
will take a DNA fault, as cr0.ts is '1' and now, because we are
in __switch_to(), math_state_restore() will get confused and will
restore the next task's FP state and will save it in prev tasks's FP state.
Remember, in __switch_to() we are already on the stack of the next task
but take a DNA fault for the prev task.
This causes the fpu leakage.
Fix the padlock instruction usage by calling them inside the
context of new routines irq_ts_save/restore(), which clear/restore cr0.ts
manually in the interrupt context. This will not generate spurious DNA
in the context of the interrupt which will fix the oops encountered and
the possible FPU leakage issue.
Reported-and-bisected-by: Wolfgang Walter <wolfgang.walter@stwm.de>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
fix spinlock recursion in hvc_console
stop_machine: remove unused variable
modules: extend initcall_debug functionality to the module loader
export virtio_rng.h
lguest: use get_user_pages_fast() instead of get_user_pages()
mm: Make generic weak get_user_pages_fast and EXPORT_GPL it
lguest: don't set MAC address for guest unless specified
commit 611e097d77
Author: Christian Borntraeger <borntraeger@de.ibm.com>
hvc_console: rework setup to replace irq functions with callbacks
introduced a spinlock recursion problem.
request_irq tries to call the handler if the IRQ is shared.
The irq handler of hvc_console calls hvc_poll and hvc_kill
which might take the hvc_struct spinlock. Therefore, we have
to call request_irq outside the spinlock.
We can move the notifier_add safely outside the spinlock as ->data must
not be changed by the backend. Otherwise, tty_hangup would fail anyway.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The correct id is the id of the main host (5591) not
the id of the PCI-to-PCI bridge AGP (0001).
Output from "lspci -nv" shows that only the former
has AGP capabilities flag set:
00:00.0 0600: 1039:5591 (rev 02)
Flags: bus master, medium devsel, latency 64
Memory at ec000000 (32-bit, non-prefetchable) [size=32M]
Capabilities: [c0] AGP version 1.0
00:02.0 0604: 1039:0001 (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: eb500000-eb5fffff
Prefetchable memory behind bridge: eb300000-eb3fffff
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On my Intel chipset (965GM), the GTT is entirely erased across
suspend/resume. This patch simply re-plays the current mapping at resume
time to restore the table.=20
I noticed this once I started relying on persistent GTT mappings across VT
switch in our GEM work -- the old X server and DRM code carefully unbind
all memory from the GTT on VT switch, but GEM does not bother.
I placed the list management and rewrite code in the generic layer on the
assumption that it will be needed on other hardware, but I did not add the
rewrite call to anything other than the Intel resume function.
Keep a list of current GATT mappings. At resume time, rewrite them into
the GATT. This is needed on Intel (at least) as the entire GATT is
cleared across suspend/resume.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Keith Packard <keithp@keithp.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Convert printks to use dev_printk().
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
I think the intent was that if no bridges matched agp_amd64_pci_table[],
we would fall back to checking for any bridge with the AGP capability.
But in the current code, we execute the fallback path only when
pci_register_driver() itself fails, which is unrelated to whether any
matching devices were found.
This patch counts the AGP bridges found in the probe() method and executes
the fallback path when none is found.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
While testing our KVM code for s390 (starting and killall kvm in a loop)
I can reproduce the following oops:
Unable to handle kernel pointer dereference at virtual kernel address 6b6b6b6b6b6b6000 Oops: 0038 [#1] SMP
Modules linked in: dm_multipath sunrpc qeth_l3 qeth_l2 dm_mod qeth
ccwgroup CPU: 1 Not tainted 2.6.27-rc1 #54
Process kuli (pid: 4409, task: 00000000b6aa5940, ksp: 00000000b7343e10)
Krnl PSW : 0704e00180000000 00000000002e0b8c
(disassociate_ctty+0x1c0/0x288) R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:3
CC:2 PM:0 EA:3 Krnl GPRS: 0000000000000000 6b6b6b6b6b6b6b6b
0000000000000001 00000000000003a6 00000000002e0a46 00000000004b4160
0000000000000001 00000000bbd79758 00000000b7343e58 00000000b8854148
00000000bd34dea0 00000000b7343c20 0000000000000001 00000000004b6d08
00000000002e0a46 00000000b7343c20 Krnl Code: 00000000002e0b7e:
eb9fb0a00004 lmg %r9,%r15,160(%r11) 00000000002e0b84:
07f4 bcr 15,%r4 00000000002e0b86:
e31090080004 lg %r1,8(%r9) >00000000002e0b8c:
d501109cd000 clc 156(2,%r1),0(%r13) 00000000002e0b92:
a784ff5d brc 8,2e0a4c 00000000002e0b96:
b9040029 lgr %r2,%r9 00000000002e0b9a:
c0e5fffff9c3 brasl %r14,2dff20 00000000002e0ba0:
a7f4ff56 brc 15,2e0a4c Call Trace:
([<00000000002e0a46>] disassociate_ctty+0x7a/0x288)
[<0000000000141fe6>] do_exit+0x212/0x8d4
[<0000000000142708>] do_group_exit+0x60/0xcc
[<0000000000150660>] get_signal_to_deliver+0x270/0x3ac
[<000000000010bfd6>] do_signal+0x8e/0x8dc
[<0000000000113772>] sysc_sigpending+0xe/0x22
[<000001ff0000b134>] 0x1ff0000b134
INFO: lockdep is turned off.
Last Breaking-Event-Address:
[<00000000002e0a48>] disassociate_ctty+0x7c/0x288
Kernel panic - not syncing: Fatal exception: panic_on_oops
It seems that tty was already free in disassocate_ctty when it tries
to dereference tty->driver.
After moving the lock_kernel before the mutex_unlock, I can no longer
reproduce the problem.
[ This is a temporary partial fix for the documented and long standing
race in disassociate_tty. This stops most problem cases for now.
For the next release the -next tree has an initial implementation of
kref counting for tty structures and this quickfix will be dropped.
- Alan ]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by; Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus-merged' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 5177/1: arm/mach-sa1100/Makefile: remove CONFIG_SA1100_USB
[ARM] 5166/1: magician: add MAINTAINERS entry
[ARM] fix pnx4008 build errors
[ARM] Fix SMP booting with non-zero PHYS_OFFSET
[ARM] 5185/1: Fix spi num_chipselect for lubbock
[ARM] Move include/asm-arm/arch-* to arch/arm/*/include/mach
[ARM] Add support for arch/arm/mach-*/include and arch/arm/plat-*/include
[ARM] Remove asm/hardware.h, use asm/arch/hardware.h instead
[ARM] Eliminate useless includes of asm/mach-types.h
[ARM] Fix circular include dependency with IRQ headers
avr32: Use <mach/foo.h> instead of <asm/arch/foo.h>
avr32: Introduce arch/avr32/mach-*/include/mach
avr32: Move include/asm-avr32 to arch/avr32/include/asm
[ARM] sa1100_wdt: use reset_status to remember watchdog reset status
[ARM] pxa: introduce reset_status and clear_reset_status for driver's usage
[ARM] pxa: introduce reset.h for reset specific header information
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (99 commits)
pkt_sched: Fix actions referencing
bnx2x: fix logical op
tcp: (whitespace only) fix confusing indentation
pkt_sched: Fix qdisc config when link is down.
[Bluetooth] Add full quirk implementation for btusb driver
[Bluetooth] Removal of unnecessary ignore module parameter
[Bluetooth] Add parameters to control BNEP header compression
ath9k: Revamp wireless mode usage
ath9k: More unused macros
ath9k: Remove a few unused macros and fix indentation
ath9k: Use mac80211's band macros and remove enum hal_freq_band
ath9k: Remove redundant data structure ath9k_txq_info
ath9k: Cleanup data structures related to HW capabilities
ath9k: work around gcc ICEs
ath9k: Add new Atheros IEEE 802.11n driver
ath5k: remove Atheros 11n devices from supported list
list.h: add list_cut_position()
list.h: Add list_splice_tail() and list_splice_tail_init()
p54: swap short slot time dcf values
rt2x00: Block all unsupported modes
...
This driver was declared obsolete over 2 years ago, the alternative
console driver for legacy iSeries (hvc_iseries) was made the default
over 1 year ago and this driver has been build broken for over 3
months, so remove it.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Valdis Kletnieks