As we allow soft-reset to be performed only on inference devices,
having the sysfs nodes may cause a confusion. Hence, we remove those
nodes on training ASICs.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Currently sysfs support dumping a single infineon version, in
future asics we will have two infineon versions.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Need to allow user retrieve data during reset and afterwards without
the need to reopen the device.
Did it by seperating the user peocesses list into two lists:
1. fpriv_list which contains list of user processes that opened
the device (currently only one).
2. fpriv_ctrl_list which contains list of user processes that opened
the control device. This processes in this list shall not be
killed during reset, only when the device is suddenly removed from
PCI chain.
Signed-off-by: Dani Liberman <dliberman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In legacy f/w that use old hwmon.h file, the values of the hwmon
enums are different than the values that are in newer kernels (5.6
and above).
Therefore, to support working with those f/w, we need to do some
fixup before registering with the hwmon subsystem and also when
calling the functions that communicate with the f/w to retrieve
sensors information.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In order to increase cpucp messaging reliability we will add
the current PI value to the descriptor sent to F/W.
F/W will wait for the PI value as an indication of a valid packet.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The driver supports only a single user anyway, so there is no point
in checking whether we are in_debug state when a user tries to open
the device, because if we are in_debug, it means a user is already
using the device.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Current clock throttling period returned from driver was wrong due
to wrong time comparison.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The original multi-CS design assumption that stream masters are used
exclusively (i.e. multi-CS with set of stream master QIDs will not get
completed by CS not from the multi-CS set) is inaccurate.
Thus multi-CS behavior is now modified not to treat such case as an
error.
Instead, if we have multi-CS completion but we detect that no CS from
the list is actually completed we will do another multi-CS wait (with
modified timeout).
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Dani Liberman <dliberman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
It was an error to save the compute context's pointer in the device
structure, as it allowed its use without proper ref-cnt.
Change the variable to a flag that only indicates whether there is
an active compute context. Code that needs the pointer will now
be forced to use proper internal APIs to get the pointer.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
There are multiple places where the code needs to get the context's
pointer and increment its ref cnt. This is the proper way instead
of using the compute context pointer in the device structure.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Pass the user's context pointer into the etr configuration function
to extract its ASID.
Using the compute_ctx pointer is an error as it is just an indication
of whether a user has opened the compute device.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Compute context pointer in hdev shouldn't be used for fetching the
context's pointer.
If an object needs the context's pointer, it should get it while
incrementing its kref, and when the object is released, put it.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The driver supports only a single context. Therefore, no need to check
if the user context that is closed is the compute context. The user
context, if exists, is always the compute context.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Fix a bug where in case of failure to allocate idr, the handle's
memory wasn't freed as part of the error handling code.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The reset flags used by the reset thread are currently a mix of
hard-coded values and a specific flag which is passed from the context
that initiates the reset.
To make it easier to pass more flags in future from this context to the
reset thread, modify it to pass all the original reset flags to the
thread.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Because info ioctl is used to retrieve data, some of its opcodes may be
used during hard reset.
Other ioctls should be blocked while device is not operational.
Signed-off-by: Dani Liberman <dliberman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
For debug purpose, add SOB address and SOB initial counter value
before current submission to uAPI output.
Using SOB address and initial counter, user can calculate how much of
the submmision has been completed.
Signed-off-by: Dani Liberman <dliberman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Reporting FW errors involves reading of the error registers.
In case we have a corrupted FW descriptor we cannot do that since the
dynamic scratchpad is potentially corrupted as well and may cause kernel
crush when attempting access to a corrupted register offset.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Driver should handle events during soft-reset as F/W is not
going through reset and it keeps sending events towards host.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Currently we dump the physical IRQ line index in host if an event
is received during reset. This ID is confusing as it means nothing
to the user.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In new f/w versions, it is required to explicitly indicate the power
information type when querying the F/W for power info.
When getting the current power level it should be set to power_input.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Some info ioctls can be served even if the device is disabled or
in reset. Hence, we enable more info ioctls during reset, as these
ioctls do not require any H/W nor F/W communication.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Race example scenario:
1. User have 2 threads that waits on multi CS:
- thread_0 waits on QID 0 and uses multi CS context 0.
- thread_1 waits on QID 1 and uses multi CS context 1.
2. thread_1 got completion and release multi CS context 1.
3. CS related to multi CS of thread_0 starts executing
complete_multi_cs function, the first iteration of the loop
completes the multi CS of thread_0, hence multi CS context 0
is released.
4. thread_1 waits on QID 1 and uses multi CS context 0.
5. thread_0 waits on QID 0 and uses multi CS context 1.
6. The second iterattion of the loop (from step 3) starts, which
means, start checking multi CS context 1:
- multi CS contetxt is being used by thread_0 waiting on QID 0.
- The fence of the CS (still CS from step 3) has QID map the same
as the multi CS context 1.
- multi CS context 1 (thread_0) gets completion on CS that triggered
already thread_0 (with multi CS context 0) and is no longer
being waited on.
Fixed by exiting the loop in complete_multi_cs after getting completion
Signed-off-by: Dani Liberman <dliberman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
As device boot warnings clears the indication from the error mask,
they must be located together before the unknown error validation.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The ASIC-specific soft_reset_late_init() is now called after either
soft-reset or reset-upon-device-release. Therefore, it needs a more
appropriate name.
No need to split it to two functions, as an ASIC either supports
soft-reset or reset-upon-device-release.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Reset upon device release is not a soft-reset from user/system point
of view. As such, we shouldn't count that reset in the statistics we
gather and expose to the monitoring applications.
We also shouldn't print soft-reset when doing the reset upon device
release.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Changing the frequency automatically is only done in Goya. In future
ASICs this is done inside the firmware. Therefore, move the common code
into the Goya specific files.
Main changes as part of the commit are:
1. The thread for setting frequency is moved from device_late_init
to goya_late_init
2. hl_device_set_frequency is removed from hl_device_open as it is
not relevant for other ASICs and for Goya it is taken care by
the thread
3. hl_device_set_frequency is renamed as goya_set_frequency
Signed-off-by: Rajaravi Krishna Katta <rkatta@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Hard-reset is mutually exclusive with reset-on-device-release.
Therefore, if such a request arrives to the reset function, abort
the reset and return an error to the callee.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Currently there is a deadlock in driver in scenarios where MMU
cache invalidation fails. The issue is basically device reset
being performed without releasing the MMU mutex.
The solution is to skip device reset as it is not necessary.
In addition we introduce a slight code refactor that prints the
invalidation error from a single location.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
If a device reset has started, there is a chance that the heartbeat
function will fail because the device is disabled at the beginning
of the reset function.
In that case, we don't want the error message to appear in the log.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
A new uAPI is added for debug purposes of the user-space to retrieve
errors related data from previous session (before device reset was
performed).
Inforamtion is filled when a razwi or CS timeout happens and can
contain one of the following:
1. Retrieve timestamp of last time the device was opened and razwi or
CS timeout happened.
2. Retrieve information about last CS timeout.
3. Retrieve information about last razwi error.
This information doesn't contain user data, so no danger of data
leakage between users.
Signed-off-by: Dani Liberman <dliberman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
AS TPM error indication is not fatal, driver should dump a warning
and continue booting.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
I2C debugfs support is limited to 1 byte. We extend functionality
to more than 1 byte by using one of the pad fields as a length.
No backward compatibility issues as new F/W versions will treat 0
length as a 1 byte length transaction.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Divide the code into 3 different parts:
- Copy kernel parameters
- Setting device behaivor per asic
- Fixup of various device parameters according to the device behaivor.
In addition, remove non-relevant code for upstream (simulator support).
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Add implementation for new opcodes in the INFO IOCTL:
1. Retrieve the replaced DRAM rows from f/w.
2. Retrieve the pending DRAM rows from f/w.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Refactor the wait-for-user-interrupt routine to make it more
generic for re-use for other user exposed h/w interfaces in future
ASICs.
Signed-off-by: Bharat Jauhari <bjauhari@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In addition to the clock throttling reason, user should be able
to obtain also the start time and the duration of the throttling
event.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In order to increase maximum wait-for-interrupt timeout, change it
to 64 bit variable. This wait is used only by newer ASICs, so no
problem in changing this interface at this time.
Signed-off-by: Dani Liberman <dliberman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
CPUCP_PACKET_POWER_GET packet type was used for both
hl_get_power() and hl_set_power().
To align with other sensor functions hl_set_power()
should use CPUCP_PACKET_POWER_SET.
This packet will only be used with newer ASICs, so need to add
a compatibility flag to the asic properties to indicate whether to use
this packet or the GET packet.
Signed-off-by: Rajaravi Krishna Katta <rkatta@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In case of device reset, the driver does a force trigger on all waiting
users to release them from waiting. However, the driver does not handle
error scenario while waiting.
hl_interrupt_wait_ioctl() now exits the wait in case of an error with
abort status.
Signed-off-by: Bharat Jauhari <bjauhari@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Once we read indication of whether f/w is doing the reset, we don't
want to clear it, until the next time we read this indication.
Otherwise, we might be in a state of wrong indication.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Using a variable poll interval for fw loading allows us to support
much slower environments (emulation) while changing only a single
line in the code, instead of choosing a different interval in each
function that polls.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Up until now the driver stored indication if Linux was loaded on the
device CPU. This was needed in order to coordinate some tasks that are
performed by the Linux.
In future ASICs, many of those tasks will be performed by the boot
fit, so now we need the same indication of boot fit load status.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The PCI MMU cache is two layered. The upper layer, memcache, uses cache
lines, the bottom layer doesn't.
Hence, after PMMU map operation we have to invalidate memcache, to avoid
the situation where the new entry is already in the cache due to its
cache line being fully in the cache.
However, we do not have to invalidate the lower cache, and here we can
optimize, since cache invalidation is time consuming.
Signed-off-by: Yuri Nudelman <ynudelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The enum vm_type was abused, used once as a value (indication
memory type for map) and once as a flag (for cache invalidation).
This makes it hard to add new and still keep it meaningful, hence it
is better to split into one enum for values and one for flags.
Signed-off-by: Yuri Nudelman <ynudelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Currently LAST_MASK is a global, but really it is an MMU implementation
specific. We need this change for future ASICs.
Signed-off-by: Yuri Nudelman <ynudelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
VA blocks are currently stored in an inconsistent way. Sometimes block
end is inclusive, sometimes exclusive. This leads to wrong size
calculations in certain cases, plus could lead to a segmentation fault
in case mapping process fails in the middle and we try to roll it back.
Need to make this consistent - start inclusive till end inclusive.
For example, the regions table may now look like this:
0x0000 - 0x1fff : allocated
0x2000 - 0x2fff : free
0x3000 - 0x3fff : allocated
Signed-off-by: Yuri Nudelman <ynudelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The boot status flag "SRAM available" can be set by f/w Linux (in the
general case) or by f/w uboot (in some specific debug scenario) but
never by f/w preboot.
Hence, when polling the boot status flags in the preboot stage we do not
want to poll on "SRAM Avialable".
The special case in which uboot set this flag is when we are running
special debug scenario without Linux. In this case, at some point during
the boot, the uboot relocates its code to the DRAM and then set the
specified flag.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
VA range info could assist in debugging VA allocation bugs.
Signed-off-by: Yuri Nudelman <ynudelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In the dynamic FW load protocol the boot status is updated to
"Ready to Boot" once uboot is active.
Polling on other boot status values is a residue of code duplication
from the static protocol and should be removed.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In order to better track where in the kernel the dma-buf code is used,
put the symbols in the namespace DMA_BUF and modify all users of the
symbols to properly import the namespace to not break the build at the
same time.
Now the output of modinfo shows the use of these symbols, making it
easier to watch for users over time:
$ modinfo drivers/misc/fastrpc.ko | grep import
import_ns: DMA_BUF
Cc: "Pan, Xinhui" <Xinhui.Pan@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: dri-devel@lists.freedesktop.org
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sumit Semwal <sumit.semwal@linaro.org>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://lore.kernel.org/r/20211010124628.17691-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To avoid checking if fence exists multipled times, changed fence
handling to depend only on the fence status field:
Busy, which means CS still did not completed :
Add its QID so multi CS wait on its completion.
Finished, which means CS completed and fence exists:
Raise its completion bit if it finished mcs handling and
update if necessary the earliest timestamp.
Gone, which means CS already completed and fence deleted:
Update multi CS data to ignore timestamp and raise its
completion bit.
Signed-off-by: Dani Liberman <dliberman@habana.ai>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
No need to check the return value if the following action is the same for
both cases. In addition, now that hl_ctx_free() doesn't print if the
context is not released, its name can be misleading as the context might
stay alive after it is executed with no indication for that.
Hence we can discard it and simply put the refcount.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Remove the flag that determines whether to take a timestamp once the
interrupt arrives.
Instead, always take the timestamp once per interrupt.
This is a must for the user-space to measure its graph operations
to evaluate the graph computation time.
Signed-off-by: Yuri Nudelman <ynudelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
When adding a new node to the hpriv list, the driver should
initialize its fields before adding the new node.
Otherwise, there may be some small chance of another thread traversing
that list and accessing the new node's fields without them being
initialized.
Signed-off-by: Moti Haimovski <mhaimovski@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Make the frequency set/get functionality common to all ASICs.
This makes more code reusable when adding support for newer ASICs.
Signed-off-by: Rajaravi Krishna Katta <rkatta@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Implement the calls to the dma-buf kernel api to create a dma-buf
object backed by FD.
We block the option to mmap the DMA-BUF object because we don't support
DIRECT_IO and implicit P2P. We only implement support for explicit P2P
through importing the FD of the DMA-BUF.
In the export phase, we provide to the DMA-BUF object an array of pages
that represent the device's memory area. During the map callback,
we convert the array of pages into an SGT. We split/merge the pages
according to the dma max segment size of the importer.
To get the DMA address of the PCI bar, we use the dma_map_resources()
kernel API, because our device memory is not backed by page struct
and this API doesn't need page struct to map the physical address to
a DMA address.
We set the orig_nents member of the SGT to be 0, to indicate to other
drivers that we don't support CPU mappings.
Note that in Habanalabs's ASICs, the device memory is pinned and
immutable. Therefore, there is no need for dynamic mappings and pinning
callbacks.
Also note that in GAUDI we don't have an MMU towards the device memory
and the user works on physical addresses. Therefore, the user doesn't
pass through the kernel driver to allocate memory there. As a result,
only for GAUDI we receive from the user a device memory physical address
(instead of a handle) and a size.
We check the p2p distance using pci_p2pdma_distance_many() and refusing
to map dmabuf in case the distance doesn't allow p2p.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Reviewed-by: Gal Pressman <galpress@amazon.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
When polling fences for multi CS, it is possible that fence is
no longer exists (its corresponding CS completed and the fence was
deleted) but we still accessing its parameters, causing NULL pointer
dereference.
Fixed by checking if fence exits before accessing its parameters.
Signed-off-by: Dani Liberman <dliberman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Race condition occurs when CS fence completes and multi CS did not
completed yet, while waiting for multi CS ends and returns indication
to user that the CS completed. Next wait for multi CS may be triggered
by previous multi CS completion without any current CS completed,
causing an error.
Example scenario :
1. User do multi CS wait for CSs 1 and 2 on master QID 0
2. CS 1 and 2 reached the "cs release" code. The thread of CS 1
completed both the CS and multi CS handling but the completion
thread of CS 2 completed the CS but still did not executed
complete_multi_cs (note that in CS completion the sequence is to
first do complete all for the CS and then another complete all to
signal the multi_cs)
3. User received indication that CS 1 and 2 completed (since we check
the CS fence and both indicated as completed) and immediately waits
on CS 3 and 4, also on master QID 0.
4. Completion thread of CS2 executed complete_multi_cs before
completion of CS 3 and 4 and so will trigger the multi CS wait of
CSs 3 and 4 as they wait on master QID 0.
This will trigger multi CS completion although none of its
current CS has been completed.
Fixed by adding multi CS complete handling indication for each CS.
CS will be marked to the user as completed only if its fence completed
and multi CS handling is done.
Signed-off-by: Dani Liberman <dliberman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
There may be a situation where drivers receives continuous fatal H/W
error events from FW immediately post reset cycle.
This may be due to some fault on the silicon itself.
In such case its better to bypass reset cycle so we won't be stuck in
endless loop of resets.
This commit bypasses reset request in case driver received two back to
back FW fatal error before first occurrence of heartbeat event.
Signed-off-by: Bharat Jauhari <bjauhari@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Taking an accurate timestamp in a close proximity of the interrupt is
required for user side statistics management.
Signed-off-by: Yuri Nudelman <ynudelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The driver allows only a single process to open a device's FD at any
single time. This is done by checking "hdev->compute_ctx" under mutex.
Therefore, to prevent a race between the moment a user closes it's FD
and when another user tries to open the device, we need to make sure
that clearing this variable is the very last thing that is done in the
code of the FD's release.
I'm moving the idle check before clearing this variable and the
"reset on device release". btw, if the reset happens it will prevent
any other user from opening the device until the reset is finished.
An important thing to note is that we need to remove the user process
that is closing the device from the process list BEFORE calling the
reset function. That is to prevent a case where the reset code will
try to kill that user process and it is unnecessary as the process
doesn't hold any device/driver resources anymore.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Reset to the device is not necessarily due to an error, so print it
as info instead of error.
In addition, print the type of reset we are doing:
- reset of the entire device (aka hard reset)
- reset of the device after user have released it (less than hard reset)
- lighter reset of an inference device (aka soft reset)
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Soft-reset is the procedure where we reset only the compute/DMA engines
of the device, without requiring the current user-space process to
release the device.
This type of reset can happen if TDR event occurred (a workload got
stuck) or by a root request through sysfs.
This is only relevant for inference ASICs, as there is no real-world
use-case to do that in training, because training runs on multiple
devices.
In addition, we also do (in certain ASICs) a reset upon device release.
That reset uses the same code as the soft-reset.
Therefore, to better differentiate between the two resets, it is better
to rename the soft-reset support as "inference soft-reset", to make
the code more self-explanatory.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The translation in debugfs of device memory MMU virtual addresses was
wrong as it did not take into consideration the fact that the page
sizes there can be not power of 2.
Signed-off-by: Yuri Nudelman <ynudelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In order to avoid user target value wraparound, we modify the
current interface so user will be able to wait for an 8-byte
target value rather than a 4-byte value.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
During TDR handling, we check multiple times if CS is valid.
No need to perform this check as CS must be valid at all time
during the TDR handling.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Add support to retrieve following power info via HWMON:
- instantaneous power value
- highest value since last reset
- reset the highest place holder
Signed-off-by: Rajaravi Krishna Katta <rkatta@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Instead of having dedicated function per message that we want to send
to the firmware in COMMS protocol, have a generic function that we can
call to from other parts of the driver
Signed-off-by: Alon Mizrahi <amizrahi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Instead of using the Linux kernel HWMON enums definition when
communicating with the firmware, use proprietary HWMON based enums
i.e. map hwmon.h header enum to cpucp_if.h based enum while.
This is needed because the HWMON enums are not forcing backward
compatibility and therefore changes can break compatibility between
newer driver and older firmware.
The driver will check for CPU_BOOT_DEV_STS0_MAP_HWMON_EN bit to
validate if f/w supports cpucp->hwmon enum mapping to support older
firmware where this mapping won't be available.
Signed-off-by: Rajaravi Krishna Katta <rkatta@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Command submission timeout is currently determined during driver
loading time. As some environments requires this timeout to be
modified in runtime, we introduce a new debugfs node that controls
the timeout value without the need to reload the driver.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In wait for CS IOCTL code, the driver resets the incoming args structure
before returning to the user, regardless of the return value of the
IOCTL.
In case the IOCTL returns EINTR, resetting the args will result in error
in case the userspace will repeat the ioctl call immediately (which is
the behavior in the hl-thunk userspace library).
The solution is to reset the args only if the driver returns success (0)
as a return value for the IOCTL.
Signed-off-by: Rajaravi Krishna Katta <rkatta@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Staged submission consists of multiple command submissions.
In order to be explicit, driver should return a single cs sequence
for every cs in the submission, or else user may try to wait on
an internal CS rather than waiting for the whole submission.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Add handling for case where the user doesn't set wait offset,
and keeps it as 0. In such a case the driver will decrement one
from this zero value which will cause the code to wait for
wrong number of signals.
The solution is to treat this case as in legacy wait cs,
and wait for the next signal.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
As user can send wrong arguments to multi CS API, we rate limit
the amount of errors dumped to dmesg, in addition we change the
severity to warning.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
As collective wait operation is required only when NIC ports are
available, we disable the option to submit a CS in case all the ports
are disabled, which is the current situation in the upstream driver.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In case of single staged cs with both first/last indications
set, we reach a scenario where in cs_release function flow
we don't cancel the TDR work before freeing the cs memory,
this lead to kernel OOPs since when the timer expires
the work pointer will be freed already.
In addition treat wait encaps cs "not found" handle
as "OK" for the user in order to keep the user interface
for both legacy and encpas signal/wait features the same.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
We have a potential race where a user interrupt can be received
in between user thread value comparison and before request was
added to wait list. This means that if no consecutive interrupt
will be received, user thread will timeout and fail.
The solution is to add the request to wait list before we
perform the comparison.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
When the f/w runs in secured mode, it can reset the ASIC when certain
events occur. In unsecured mode, the driver asks the f/w to reset the
ASIC for those events.
We need to perform the entire reset procedure but without accessing the
ASIC. i.e. without halting the engines and without sending messages
to the f/w.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Fix 2 areas in the code where it's possible the code will
go to sleep while holding a spinlock.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
copy_from_user might sleep so we can never call it when we have
a spinlock.
Moreover, it is not necessary in waiting for user interrupt, because
if multiple threads will call this function on the same interrupt,
each one will have it's own fence object inside the driver. The
user address might be the same, but it doesn't really matter to us,
as we only read from it.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Checking if the device is operational when entering the function to
wait for user interrupt is not something that is useful or necessary.
It is not done in any other wait_for_cs ioctl path.
If the device becomes non-operational during the wait, the reset
function will make sure the process wait is interrupted.
Instead, move the check to the beginning of hl_wait_ioctl(). It will
block any attempt to wait on CS or user interrupt once the device
is already marked as non-operational.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Because this spinlock is taken in an interrupt handler, we must use
the spin_lock_irqsave/irqrestore version to disable the interrupts
on the local CPU. Otherwise, we can have a potential deadlock (if
the interrupt handler is scheduled to run on the same cpu that the
code who took the lock was running on).
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
On init, the disabled state is cleared right before hw_init and that
causes the device to report on "Operational" state before the device
initialization is finished. Although the char device is not yet exposed
to the user at this stage, the sysfs entries are exposed.
This can cause errors in monitoring applications that use the sysfs
entries.
In order to avoid this, a new state "in device creation" is introduced
to ne reported when the device is not disabled but is still in init
flow.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
It is useful to have the ability to see which user address was pinned
to which physical address during the initial mapping. We already have
all that info stored, but no means to search this data (which may be
quite large).
Signed-off-by: Yuri Nudelman <ynudelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
During the integration, the multi-CS requirements were refined:
- The multi CS call shall wait on "per-ASIC" predefined stream masters
instead of set of streams.
- Stream masters are set of QIDs used by the upper SW layers (synapse)
for completion (must be an external/HW queue).
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Various f/w versions have different timeouts, so increase the default
timeout to accommodate all the options.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The address resolution via debugfs was not taking into consideration the
page offset, resulting in a wrong address.
Signed-off-by: Yuri Nudelman <ynudelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Currently userptr endpoint in debugfs prints out virtual addresses
in the user process memory space, without specifying their owner process
ID. User space virtual address is meaningless without knowing the owner
process.
Signed-off-by: Yuri Nudelman <ynudelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
For some ASICs, the f/w reads the msg_to_cpu_reg value after
reset, and for some it doesn't.
Therefore, to be sure f/w doesn't read a wrong value after reset, we
need to clear this register before the reset occurs.
Signed-off-by: Koby Elbaz <kelbaz@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In order to better support variants of the same ASIC
the set_pci_regions function is now an ASIC function which
allows each ASIC to implement it internally, thus keeping
all definitions static to the file.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Done as the bar size can exceed 4GB.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Add the server type property to the hl_info_hw_ip_info structure
that is exposed to the user via the INFO IOCTL.
This is needed by the userspace s/w stack to know the connections map
of the internal links that connect the ASIC among themselves inside the
server.
The F/W will tell us, as part of the NIC information, the server type
that the GAUDI is located in.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
This warning is redundant as we will print a notice in case the device
is still in use after the FD was closed. No need to print the same
message per context.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
This commit is the second part of the encapsulated signals feature.
It contains the driver support for submission of cs with encapsulated
signals and the wait for them.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The signaling from within encapsulated OP capability is merged into the
existing stream architecture, such that one can trigger multiple
signaling from an encapsulated op, according to the time the event
was done in the graph execution and avoid the need to wait for the
whole encapsulated OP execution to be complete before the stream can
signal.
This commit implements only the reserve/unreserve part.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Currently the SOB reset was in fence release function which happens
only at the CS wraparound during the CS allocation time.
In order to support the new encapsulated signals reservation feature,
we need to move the SOB reset to an earlier phase because this SOB
could reach it's max value very fast using the signal reservation.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
When user sends multiple CSs, waiting for each CS is not efficient
as it involves many user-kernel context switches.
In order to address this issue we add support to "wait on multiple CSs"
using a new uAPI which can wait on maximum of 32 CSs. The new uAPI is
defined using a new flag - WAIT_FOR_MULTI_CS - in the wait_for_cs IOCTL.
The input parameters for this uAPI will be:
@seq: user pointer to an array of up to 32 CS's sequence numbers.
@seq_array_len: length of sequence array.
@timeout_us: timeout for waiting for any CS.
The output paramateres for this API will be:
@status: multi CS ioctl completion status (dedicated status was added as
well).
@flags: bitmap of output flags of the CS.
@cs_completion_map: bitmap for multi CS, if CS sequence that was placed
in index N in input seq array has completed- the N-th
bit in cs_completion_map will be 1, otherwise it will
be 0.
@timestamp_nsec: timestamp of the first completed CS
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
To add proper support for wait-for-multi-CS, locking the CS lock
for each CS fence in the list is not efficient.
Instead, this patch add support to lock the CS lock once to get all
required fences.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The driver quietly handles memory mappings that were not freed so no
need to print a warning about that when user closes the FD.
Accordingly, revise the text that is printed in case the device is
still in use after the user process closed the FD.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
There is a scenario where an ongoing soft reset would race with an
ongoing heartbeat routine, eventually causing heartbeat to fail and
thus to escalate into a hard reset.
With this fix, soft-reset procedure will disable heartbeat CPU messages
and flush the (ongoing) current one before continuing with reset code.
Signed-off-by: Koby Elbaz <kelbaz@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Each ASIC can have a different offset to add to a host dma address,
to enable the ASIC to access that host memory.
The usage for this can be common code so add this to the asic
property structure.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Recently, the size parameter in userptr structure was change to u64.
As a result, we need to change the type of the local range_size
in device_va_to_pa() to u64 to avoid overflow.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
If hard reset fails after the call to hw_fini and before loading the
linux image to the device, a subsequent call to hw_fini should
communicate via COMMS (or MSG_TO_CPU regs for old FW versions).
However, the driver still tries in this case to communicate via the GIC,
and thus no hard reset is actually done.
To avoid that, the patch clears the linux_loaded flag after every call
to hw_fini.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In case of host-resident MMU, when the page tables pool is destroyed,
its pointer is not nullified correctly.
As a result, on a device fini which happens after a failing reset, the
already destroyed pool is accessed, which leads to a kernel panic.
The patch fixes the setting of the pool pointer to NULL.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
This function will be used for more mmap operations than just
mmaping CBs.
Signed-off-by: Zvika Yehudai <zyehudai@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
With the infrastructure in place, monitors and fences dump shall be
implemented.
Signed-off-by: Yuri Nudelman <ynudelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
To improve the user's ability to debug the case where a workload that
is part of executing training/inference of a topology is getting stuck,
we need to add a 'core dump' each time a CS times-out. The 'core dump'
shall contain all relevant Sync Manager information and corresponding
fence values.
The most recent dumps shall be accessible via debugfs, under
'state_dump' node. Reading from the node will provide the oldest dump
available. Writing an integer value X will discard X dumps, starting
with the oldest one, i.e. subsequent read will now return newer
dumps.
Signed-off-by: Yuri Nudelman <ynudelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The previous function we used, find_get_pid(), wasn't good in case
the user process was run inside docker.
As a result, we didn't had the PID and we couldn't kill the user
process in case the device got stuck and we needed to reset the
device.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Sometimes we may need to disable optimization of using huge pages
in our memory management code. Add such a flag to the function that
creates the list of physical pages that would be programmed into the
device MMU.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Increase the size variable in the userptr structure to 64-bit. That
variable describes the size of the memory allocation of the user that
is now being mapped into the device. The mapping can be larger than
4GB, so we need to support it.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Same as we handle it in the regular wait for CS, we need to handle the
case where the waiting for user interrupt was interrupted. In that case,
we need to return correct error code to the user.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In device fini there was missing a call to release all pending user
interrupts. That can cause a process to be stuck inside the driver's
IOCTL of wait for interrupts, in case the device is removed or
simulator is killed at the same time.
In addition, also call to remove inactive codec job was missing.
Moreover, to prevent such errors in the future (where code is added
to reset path but not to device fini), we moved some common parts
to two dedicated functions:
cleanup_resources
take_release_locks
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In case user interrupt arrived but the completion value is less than
the target value, we want to retry the wait.
However, before the retry we must reinitialize the completion object,
under spin-lock, so the wait function won't exit immediately because
the completion object is already completed (from the previous
interrupt).
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Update recent changes made in firmware header files, which contain
a minor COMMS protocol change and new error status definitions.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
A new user flag is required to make memory map hint mandatory, in
contrast to the current situation where it is best effort.
This is due to the requirement to map certain data to specific
pre-determined device virtual address ranges.
Signed-off-by: Yuri Nudelman <ynudelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Add support for pre-determined driver-reserved device VA address ranges.
This is needed for future ASIC support where some contents must be
mapped into these pre-determined ranges because the H/W will be
configured using these ranges.
In case the user asks to map a VA without a hint address, avoid
allocating the device VA from the reserved ranges.
Make sure the validation checks of the hint address take into account
situation where the DRAM page size is not pow of 2.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
There is code related to hard-reset, which is done in gaudi specific
code. However, this code can be used by future ASICs and therefore it
is better to move it to the common code section.
Signed-off-by: Koby Elbaz <kelbaz@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In preparation for a new feature that allows the user to reserve
signals ahead of submissions, we need to change a current assumption
in the code.
Currently, the driver uses 2 SOBs to support signal CS. When the first
SOB reaches max value, the driver switches to the other one and assumes
that when it will need to switch back to the first one, all of the
signals have already been handled.
This assumption won't hold when the new feature will be added, because
using signal reservation, the driver can reach the max SOB value very
fast.
The change is to add a validity check when submitting a signal CS, to
make sure the previous SOB is available (all the signals attached to
it indeed finished).
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
We introduce a new type of reset which is reset upon device release.
This reset is very similar to soft reset except the fact it is
performed only upon device release and not upon user sysfs request
nor TDR.
The purpose of this reset is to make sure the device is returned to
IDLE state after the current user has finished working with the device.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
To be able to debug long-running CS better, without changing the
userspace code, we are adding a new option through debugfs interface
to skip the reset of the device in case of CS timeout.
Signed-off-by: Yuri Nudelman <ynudelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
There was a rogue #ifdef that crept into the upstream code for
backwards compatibility which isn't needed of course.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In a system with multiple ASICs, there is a need to provide monitoring
tools with information on how long a device was opened and how many
times a device was opened.
Therefore, we add a new opcode to the INFO ioctl to provide that
information.
Signed-off-by: Yuri Nudelman <ynudelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
pin_user_pages_fast() might fail and return a negative number, or pin
less pages than requested and return the number of the pages that were
pinned.
For the latter, it is informative to print also the memory size and the
number of requested pages.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: 2e5eda4681 ("habanalabs: PCIe Advanced Error Reporting support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Firmware in habanalabs devices is composed of several components.
During device initialization, we read these versions from the device.
Print them during device initialization to allow better visibility in
automated systems.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Hard reset flow on PLDM might take more than 2 minutes.
Hence add a dedicated hard reset timeout of 6 minutes for PLDM.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In current code, for dynamic f/w loading flow, DRAM scrambling is
enabled post Linux fit image is loaded to the card. This can cause the
device CPU to go into reset state.
The correct sequence should be:
1. Load boot fit image
2. Enable scrambling
3. Load Linux fit image
This commit aligns the DRAM scrambling enabling with the static f/w load
flow.
Signed-off-by: Bharat Jauhari <bjauhari@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
If there is an error in the QMAN/engine, there is no point of trying
to continue running the workload. It is better to stop to allow the
user to debug the program.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In case we have EQ fault we would like to know about it.
For this, a status bitmask was added in which EQ_FAULT bit is
set by FW in case of EQ fault.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
When converting virtual address to physical we need to add correct
offset to the physical page.
For this we need to use mask that include ALL bits of page offset.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Get rid of the need to check if boot_dev_sts is valid on every access
to value read from these registers.
This is done by storing the register value in hdev props ONLY if
register is enabled.
This way if register is NOT enabled all capability bits will not be set.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
If device is not idle after user closes the FD we must reset device
as next user that will try to open FD will encounter a non-functional
device.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Sometimes it is useful to allow the command to continue running despite
the timeout occurred, to differentiate between really stuck or just very
time consuming commands. This can be achieved by passing a new debug
flag alongside the cs, HL_CS_FLAGS_SKIP_RESET_ON_TIMEOUT.
Anyway, if the timeout occurred, a warning print shall be issued,
however this shall not fail the submission.
Signed-off-by: Yuri Nudelman <ynudelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Current implementation uses a single interrupt interface towards
FW, this interface is causing races between interrupt types.
We split this interface to interface per interrupt type.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
There is no dependency when probing multiple devices so indicate to the
kernel that it can probe our devices in ASYNC fashion.
This shortens insmod of the driver from ~2 minutes to 20 seconds on
a system with 8 devices.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Using negative logic (i.e. fw_security_disabled) is confusing.
Modify the flag to use positive logic (fw_security_enabled).
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
This is needed because legacy FW 'communication' protocol will soon
become obsolete.
Because COMMS is a boot protocol, communicating through it is supported
only until Linux is loaded to the device CPU, where in that case we
will fallback to the former implementation.
Signed-off-by: Koby Elbaz <kelbaz@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Security is set based on PCI ID, and after reading preboot status bits.
GIC usage is set in both scenarios since GIC can't be used when security
is enabled.
Moreover, writing to GIC/SP is enabled only after Linux is fully loaded.
Signed-off-by: Koby Elbaz <kelbaz@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
On newer releases, host won't be able to trigger an interrupt directly
to the ASIC GIC controller.
To be able to decide whether GIC can/not be used, we must read device's
preboot status bits in a stage that precedes the possible first use of
GIC (when device is in dirty state).
Signed-off-by: Koby Elbaz <kelbaz@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
To harden the event queue mechanism, we add a running index to the
control header of the entry.
The firmware writes the index in each entry and the driver verifies
that the index of the current entry is larger by 1 of the index of
the previous entry.
In case it isn't, the driver will treat the entry as if it wasn't
valid (it won't process it but won't skip it).
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Scrubbing memory after every unmap is very costly in terms of
performance. If a user wants it he can enable it but the default
should prioritize performance.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Reading of GIC privileged status will be done after F/W is loaded,
because privileged GIC capability is only available with the correct
ARMCP version, and after it's loaded.
Such versions necessarily support COMMS, so GIC alternatives (SP regs)
will be read directly from dynamic regs.
As well, initiation of DMA QMANs will occur after F/W is loaded
since it depends on GIC configuration.
In case F/W isn't loaded there's no problem since either way
there won't be any GIC IRQ handling.
Signed-off-by: Koby Elbaz <kelbaz@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Fix issue in which the input to the function is_asic_secured was device
PCI_IDS number instead of the asic_type enumeration.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
LKD should provide hard reset cause to preboot prior to
loading any FW components (in case needed).
Current implementation is based on the new FW 'COMMS' protocol
In cased 'COMMS' is disabled - reset cause won't be sent.
Currently, only 2 reset causes are shared: HEARTBEAT & TDR.
Sending the reset cause will provide the missing watchdog
info that the firmware needs to provide to the BMC.
Signed-off-by: Koby Elbaz <kelbaz@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
An information print notifying on starting to load the f/w was removed
by mistake when moving to the new dynamic f/w loading mechanism.
Restore that print as the F/W loading usually takes between 10 to 20
seconds and this print helps the user know the status of the driver
load.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Due to new security restrictions, GIC controller can no
longer be accessed from user/kernel.
To monitor that, a new status bit will be read from preboot
caps, indicating whether direct access to GIC is blocked.
In case it is blocked, driver will use scratchpad registers
instead of using GIC interface on two main scenarios:
The first of which LKD triggers interrupts to F/W through GIC,
and the second of when LKD configures all engines/QMANs
to write to GIC when they want to report an error.
From F/W perspective, it will poll on all SPs, and once IRQ
number is retrieved, SP register is cleared, and it will perform the
write to the GIC to trigger the IRQ handler.
Signed-off-by: Koby Elbaz <kelbaz@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Maintain both STS1 and ERR1 registers used for status communication
with F/W.
Those are not maintained as we currently have less than 31
statuses/error defined and so LKD did not refer to those register.
The reason to read them now is to try to support future f/w versions
with current driver.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
When attempting to read FW component's version we should break if input
FW component is invalid in order to avoid using uninitialized
destination pointer.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
When setting "DMA mask from FW" we are reading PSOC_GLOBAL_CONF register
which is allowed only once FW has done it's iATU configuration.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Some users might want to implement their own policy of when the device
is unusable so we need to ignore this status in the driver and continue
loading as normal.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Implementing dynamic linux image load to the device.
This patch also implements the FW communication steps during the
boot-fit.
This patch also enables the dynamic protocol based on the compatibility
flag.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Implementing dynamic boot fit image load to the device.
Note that some necessary adjustment were added to the static loader as
well so that both loaders can co-exist.
as this is not the final FW load stage the dynamic FW load is still
forced to be non functional.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Hint address failure that results in a valid mapping with an address
that was allocated by the driver is not a real failure.
Therefore, the driver shouldn't notify about this in kernel log. The
user is responsible to check the returned address.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Indicate "progress" instead of "error" when reporting progress status.
Change "u-boot stopped by user" to "Cannot boot" message as
CPU_BOOT_STATUS_UBOOT_NOT_READY may indicate a fatal error that prevent
u-boot from loading firmware.
Signed-off-by: Guy Nisan <gnisan@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
iATU (internal Address Translation Unit of the PCI controller)
configuration is being done by FW right after driver enables
the PCI device. Hence, driver must add a minor sleep afterwards
in order to make sure FW finishes configuring iATU regions.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Update the common and GAUDI firmware header files to the latest version.
The latest version use the correct endianness types so this commit also
contains minor changes to the code to use the correct conversions when
reading/writing to the firmware structures.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
LKD has interfaces in which it receives device address.
For instance the debugfs_read/write variants receives device address for
CFG/SRAM/DRAM for read/write and need to translate to the mapped PCI BAR
address.
In addition, the dynamic FW load protocol dictates that the address to
which the LKD will copy the image for the next FW component will be
received as a device address and can be placed either in SRAM or DRAM.
We need to distinguish those regions as the access methods to those
regions are different (in DRAM we possibly need to set the BAR base).
Looking forward this code will be used to remove duplicated code in the
debugfs_read/write that search the memory region for the input device
address.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
First stage of the dynamic FW load protocol is to reset the protocol to
avoid residues from former load cycles.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Instead of using multiple ASIC specific copies of functions to read the
FW version use single common one that gets ASIC specific arguments.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Use mmu cache range invalidation instead of entire cache invalidation
because it yields better performance.
In GOYA and GAUDI, always use entire cache invalidation because these
ASICs don't support range invalidation.
Signed-off-by: Alon Mizrahi <amizrahi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Replace multiple arguments to init device CPU function by passing
firmware loader managing structure that is initialized per ASIC with
the loader parameters.
In addition, the FW loader management structure is now part of the
habanalabs device, this way the loader parameters will be able to be
communicated across various boot stages.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
This refactor is needed due to the dynamic FW load in which requesting
the FW file (and getting its attributes) is not immediately followed by
copying FW file content.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Start the skeleton for the dynamic F/W load by marking current preboot
code path as legacy.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
On PLDM, in case of NIC hangs, the ELBI reset to take much longer than
expected. As a result an increase in the ELBI reset timeout is required.
Signed-off-by: Moti Haimovski <mhaimovski@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Wait for interrupt timeout calculation is wrong, hence timeout occurs
when user waits on an interrupt with certain timeout values.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In case firmware has a bug and erroneously reports a status error
(e.g. device unusable) during boot, allow the user to tell the driver
to continue the boot regardless of the error status.
This will be done via kernel parameter which exposes a mask. The
user that loads the driver can decide exactly which status error to
ignore and which to take into account. The bitmask is according to
defines in hl_boot_if.h
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
This error indicates a problem in the security initialization inside
the f/w so we need to stop the device loading because it won't be
usable.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
If we read all FF from the boot status register, then something is
totally wrong and there is no point of reading specific errors.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Currently the user cannot interpret the PLL information based on index
as its exposed as an integer.
This commit exposes ASIC specific PLL indexes and maps it to a generic
FW compatible index.
Signed-off-by: Bharat Jauhari <bjauhari@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
We need to print a message to the kernel log in case we encounter
an unknown error in the f/w boot to help the user understand what
happened.
In addition, we shouldn't print unknown error in case of known errors.
Moreover, in case of warnings/info, we shouldn't return -EIO that will
fail the initialization and mark the device as disabled
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
As part of the securing GAUDI, the F/W will configure the PCI iATU
regions. If the driver identifies a secured PCI ID, it will know to
skip iATU configuration in a very early stage.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
As F/ security indication must be available before driver approaches
PCI bus, F/W security should be derived from PCI id rather than be
fetched during boot handshake with F/W.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
DRAM scrubbing can take time hence it adds to latency during allocation.
To minimize latency during initialization, scrubbing is moved to release
call.
In case scrubbing fails it means the device is in a bad state,
hence HARD reset is initiated.
Signed-off-by: Bharat Jauhari <bjauhari@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In order to minimize hard coded values between F/W and the driver, we
send msi-x indexes dynamically to the F/W.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In case of multiple ECC errors, FW will set the DEVICE_UNUSABLE bit.
On boot-up, the driver will therefore fail inserting the device.
Signed-off-by: Koby Elbaz <kelbaz@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Prefer the use of strscpy when copying the ASIC name into a char array,
to prevent accidentally exceeding the array's length.
In addition, strlcpy is frowned upon so replace it.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
When trying to debug program, the user often needs to
dump large parts of the device's DRAM, which can reach to tens of GBs.
Because reading from the device's internal memory through the PCI BAR
is extremely slow, the debug can take hours.
Instead, we can provide the user to copy data through one of the DMA
engines. This will make the operation much faster.
Currently, only GAUDI is supported.
In GAUDI, we need to find a PCI DMA engine that is IDLE and set the
DMA as secured to be able to bypass our MMU as we currently don't
map the temporary buffer to the MMU.
Example bash one-line to dump entire HBM to file (~2 minutes):
for (( i=0x0; i < 0x800000000; i+=0x8000000 )); do \
printf '0x%x\n' $i | sudo tee /sys/kernel/debug/habanalabs/hl0/addr ; \
echo 0x8000000 | sudo tee /sys/kernel/debug/habanalabs/hl0/dma_size ; \
sudo cat /sys/kernel/debug/habanalabs/hl0/data_dma >> hbm.txt ; done
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
There is a need to allow to user to send command submissions with
custom timeout as some CS take longer than the max timeout that is
used by default.
Signed-off-by: Alon Mizrahi <amizrahi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The new approach is based on the notion that the relative
current power consumption is in relation of proportionality
to device's true utilization.
Utilization info ranges between [0,100]%
Currently, dc_power values are hard-coded.
Signed-off-by: Koby Elbaz <kelbaz@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In order to use minimum of hard coded values common to LKD and F/W
a dynamic method to work with PLLs is introduced in this patch.
Formerly asic specific PLL numbering is now common for all asics.
To be backward compatible a bit in dev status is defined, if the bit is
not set LKD will keep working with old PLL numbering.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In order to shorten the time cs lock is being held, we move any
possible work outside of the cs lock.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Add a little sleep between page unmappings in case mapping of
large number of host pages failed, in order to
avoid soft lockup bug during the rollback.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In order to have a better debuggability we allow debugfs access
to user mmu mapped host memory. Non-user host memory access will be
rejected.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
fixed the following coccicheck:
./drivers/misc/habanalabs/common/sysfs.c:347:60-61: WARNING opportunity
for kobj_to_dev()
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
if reset is due to heartbeat, device CPU is no responsive in which
case no point sending PCI disable message to it.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
As there are incorrect assumptions in which some of the
initialization and data path flows cannot sleep, most allocations
are being done using GFP_ATOMIC.
We modify the code to use GFP_ATOMIC only when realy needed, as
sleepable flow should use GFP_KERNEL.
In addition add a fallback to allocate memory using GFP_KERNEL,
once ATOMIC allocation fails.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Add driver implementation for reading the current power from the device
CPU F/W.
Signed-off-by: Sagiv Ozeri <sozeri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Improve "vm" debugfs node to print also the virtual addresses which are
currently mapped to HW blocks in the device.
Signed-off-by: Sagiv Ozeri <sozeri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
For simplicity, use a single bringup flag indicating which FW
binaries should loaded to device.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Timeout in wait for interrupt is in 32-bit variable so we need to use
the correct maximum value to compare.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In order to support command submissions from user space, the driver
need to add support for user interrupt completions. The driver will
allow multiple user threads to wait for an interrupt and perform
a comparison with a given user address once interrupt expires.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In order to support user interrupts, driver must enable all MSI-X
interrupts for any case user will trigger them. We differentiate
between a valid user interrupt and a non valid one.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Because our graph contains network operations, we need to account
for delay in the network.
5 seconds timeout per CS is not enough to account for that.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Notify to the user that although he closed the FD, the device is
still in use because there are live CS and/or memory mappings (mmaps).
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
After any reset (soft or hard) the device (the engines/QMANs) should
be idle. If they are not idle, fail the reset. If it is soft-reset,
the driver will try to do hard-reset automatically. If it is hard-reset,
the driver will make the device non-operational.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The device is actually released only after the refcnt of the hpriv
structure is 0, which means all its contexts were closed.
If we reset the device while a context is still open, there are
possibilities for unexpected behavior and crashes. For example, if the
process has a mapping of a register block that is now currently being
reset, and the process writes/reads to that block during the reset,
the device can get stuck.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In order to support command submissions that are done directly from
user space, the driver must perform soft reset once user closes its FD.
In case the soft reset fails or device is not idle, a hard reset should
be performed.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
when user uses virtual addresses to access dram through debugfs,
driver translate this address to physical and use it
for the access through the pcie bar.
in case dram page size is different than the dmmu
page size, we need to have special treatment
for adding the page offset to the actual address, which
is to use the dram page size mask to fetch the page offset
from the virtual address, instead of the dmmu last hop shift.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
A device can be removed from the PCI subsystem while a process holds the
file descriptor opened.
In such a case, the driver attempts to kill the process, but as it is
still possible that the process will be alive after this step, the
device removal will complete, and we will end up with a process object
that points to a device object which was already released.
To prevent the usage of this released device object, disable the
following file operations for this process object, and avoid the cleanup
steps when the file descriptor is eventually closed.
The latter is just a best effort, as memory leak will occur.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The refcount of the "hl_fpriv" structure is not used for the control
device, and thus hl_hpriv_put() is not called when releasing this
device.
This results with no call to put_pid(), so add it explicitly in
hl_device_release_ctrl().
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The dentry for the created debugfs file was being saved, but never used
anywhere. As the pointer isn't needed for anything, and the debugfs
files are being properly removed by removing the parent directory,
remove the saved pointer as well, saving a tiny bit of memory and logic.
Cc: Oded Gabbay <ogabbay@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Tomer Tayar <ttayar@habana.ai>
Cc: Moti Haimovski <mhaimovski@habana.ai>
Cc: Omer Shpigelman <oshpigelman@habana.ai>
Cc: Ofir Bitton <obitton@habana.ai>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
hl_eq_inc_ptr() is not called from anywhere outside irq.c so mark
it as static
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Here is the large set of char/misc/whatever driver subsystem updates for
5.12-rc1. Over time it seems like this tree is collecting more and more
tiny driver subsystems in one place, making it easier for those
maintainers, which is why this is getting larger.
Included in here are:
- coresight driver updates
- habannalabs driver updates
- virtual acrn driver addition (proper acks from the x86
maintainers)
- broadcom misc driver addition
- speakup driver updates
- soundwire driver updates
- fpga driver updates
- amba driver updates
- mei driver updates
- vfio driver updates
- greybus driver updates
- nvmeem driver updates
- phy driver updates
- mhi driver updates
- interconnect driver udpates
- fsl-mc bus driver updates
- random driver fix
- some small misc driver updates (rtsx, pvpanic, etc.)
All of these have been in linux-next for a while, with the only reported
issue being a merge conflict in include/linux/mod_devicetable.h that you
will hit in your tree due to the dfl_device_id addition from the fpga
subsystem in here. The resolution should be simple.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYDZf9w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk3xgCcCEN+pCJTum+uAzSNH3YKs/onaDgAnRSVwOUw
tNW6n1JhXLYl9f5JdhvS
=MOHs
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the large set of char/misc/whatever driver subsystem updates
for 5.12-rc1. Over time it seems like this tree is collecting more and
more tiny driver subsystems in one place, making it easier for those
maintainers, which is why this is getting larger.
Included in here are:
- coresight driver updates
- habannalabs driver updates
- virtual acrn driver addition (proper acks from the x86 maintainers)
- broadcom misc driver addition
- speakup driver updates
- soundwire driver updates
- fpga driver updates
- amba driver updates
- mei driver updates
- vfio driver updates
- greybus driver updates
- nvmeem driver updates
- phy driver updates
- mhi driver updates
- interconnect driver udpates
- fsl-mc bus driver updates
- random driver fix
- some small misc driver updates (rtsx, pvpanic, etc.)
All of these have been in linux-next for a while, with the only
reported issue being a merge conflict due to the dfl_device_id
addition from the fpga subsystem in here"
* tag 'char-misc-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (311 commits)
spmi: spmi-pmic-arb: Fix hw_irq overflow
Documentation: coresight: Add PID tracing description
coresight: etm-perf: Support PID tracing for kernel at EL2
coresight: etm-perf: Clarify comment on perf options
ACRN: update MAINTAINERS: mailing list is subscribers-only
regmap: sdw-mbq: use MODULE_LICENSE("GPL")
regmap: sdw: use no_pm routines for SoundWire 1.2 MBQ
regmap: sdw: use _no_pm functions in regmap_read/write
soundwire: intel: fix possible crash when no device is detected
MAINTAINERS: replace my with email with replacements
mhi: Fix double dma free
uapi: map_to_7segment: Update example in documentation
uio: uio_pci_generic: don't fail probe if pdev->irq equals to IRQ_NOTCONNECTED
drivers/misc/vmw_vmci: restrict too big queue size in qp_host_alloc_queue
firewire: replace tricky statement by two simple ones
vme: make remove callback return void
firmware: google: make coreboot driver's remove callback return void
firmware: xilinx: Use explicit values for all enum values
sample/acrn: Introduce a sample of HSM ioctl interface usage
virt: acrn: Introduce an interface for Service VM to control vCPU
...
- replace mm/frame_vector.c by get_user_pages in misc/habana and
drm/exynos drivers, then move that into media as it's sole user
- close race in generic_access_phys
- s390 pci ioctl fix of this series landed in 5.11 already
- properly revoke iomem mappings (/dev/mem, pci files)
-----BEGIN PGP SIGNATURE-----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=lQoR
-----END PGP SIGNATURE-----
Merge tag 'topic/iomem-mmap-vs-gup-2021-02-22' of git://anongit.freedesktop.org/drm/drm
Pull follow_pfn() updates from Daniel Vetter:
"Fixes around VM_FPNMAP and follow_pfn:
- replace mm/frame_vector.c by get_user_pages in misc/habana and
drm/exynos drivers, then move that into media as it's sole user
- close race in generic_access_phys
- s390 pci ioctl fix of this series landed in 5.11 already
- properly revoke iomem mappings (/dev/mem, pci files)"
* tag 'topic/iomem-mmap-vs-gup-2021-02-22' of git://anongit.freedesktop.org/drm/drm:
PCI: Revoke mappings like devmem
PCI: Also set up legacy files only after sysfs init
sysfs: Support zapping of binary attr mmaps
resource: Move devmem revoke code to resource framework
/dev/mem: Only set filp->f_mapping
PCI: Obey iomem restrictions for procfs mmap
mm: Close race in generic_access_phys
media: videobuf2: Move frame_vector into media subsystem
mm/frame-vector: Use FOLL_LONGTERM
misc/habana: Use FOLL_LONGTERM for userptr
misc/habana: Stop using frame_vector helpers
drm/exynos: Use FOLL_LONGTERM for g2d cmdlists
drm/exynos: Stop using frame_vector helpers
When user gives us a block address to get its ID to mmap it, he also
needs to get from us the block size to pass to the driver in the mmap
function.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
when reading CPU_BOOT_DEV_STS0 reg after FW reports SRAM AVAILABLE the
value in the register might not yet be updated by FW.
to overcome this issue another "up-to-date" read of this register is
done at the end of CPU queues init.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Only after the initialization of the device is done, the driver is
ready to receive events from the F/W. The driver can't handle events
before that because of races so it will ignore events. In case of
a fatal event, the driver won't know about it and the device will be
operational although it shouldn't be.
Same logic should be applied after hard-reset.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
User must be aware of the available CQs when it needs to use them.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Current messaging communictaion protocol with cpucp can get out
of sync due to coherency issues. In order to improve the protocol
reliability, we modify the protocol to expect a different
acknowledgment for every packet sent to cpucp.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
We introduce a new mechanism named Staged Submission.
This mechanism allows the user to send a whole CS in pieces.
Each CS will not require completion rather than the
last CS. Timeout timer will be triggered upon reception of the first
CS in group.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Currently this API uses single 64 bits mask for engines idle indication.
Recently, it was observed that more bits are needed for some ASICs.
This patch modifies the use of the idle mask and the idle_extensions
mask.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In order to support staged submission feature, we need to
distinguish on which command submission we want to receive
timeout and for which we want to receive completion.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
For future ASIC support the driver allows user to map certain regions
in the device's configuration space for direct access from userspace.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In mmu debugfs node show un-scrambled physical addresses.
before read/write through data nodes, need to unscramble the
physical address before using it for pci transaction.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In order to support completions that arrive directly to the user,
the driver needs to supply the user with the first available msix
interrupt available.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Currently hint address is ignored in case va block page size
is not power of 2. We need to support th user hint address also in this
case, but only if the hint address is aligned to page size.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In order to support operation mode in which BMC is not active,
driver must not take BMC errors into consideration.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Axe 'hl_pci_set_dma_mask()' and replace it with an equivalent
'dma_set_mask_and_coherent()' call.
This makes the code a bit less verbose.
It also removes an erroneous comment, because 'hl_pci_set_dma_mask()'
does not try to use a fall-back value.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In order to support scnenarios in which driver needs access to
HW components but it cannot access them directly, we add support for
scheduling command buffers internally.
These command buffers will be transmitted upon next user command
submission context.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
A CS must increment the relevant context reference count.
We want to increment the reference inside the CS allocation function
as opposed for today where we increment it outside.
This is logical since we want to avoid explicitly incrementing
the context every time we call the CS allocate function.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
We separate some of the common code source files to different
folders for a better maintainability and testability.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Boot cpu can report errors in various boot stages.
Current implementaion does not take into consideration errors
reported in late stages, hence we will check for errors at the most
late stage when fetching cpucp information.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In case MMU is enabled, we must take MMU page size into
consideration when reporting dram size to the user.
This is because the MMU page size can be a value which is NOT
a power-of-2 value. As a result, the total DRAM size (which is always
a power-of-2 value) needed to be rounded-down.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
DRAM physical page sizes depend of the amount of HBMs available in
the device. this number is device-dependent and may also be subject
to binning when one or more of the DRAM controllers are found to
to be faulty. Such a configuration may lead to partitioning the DRAM
to non-power-of-2 pages.
To support this feature we also need to add infrastructure of address
scarmbling.
Signed-off-by: Moti Haimovski <mhaimovski@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
When working with DRAM MMU, we should supply the userspace with the
virtual start address of the DRAM instead of the physical one. This
is because the physical one has no meaning for the user as he only
knows the virtual address range.
Signed-off-by: Alon Mizrahi <amizrahi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In order to have more information while debugging boot issues,
we should print the firmware security status at every boot stage.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
For consistency, modify all memory ioctl functions to get the ioctl
arguments structure rather than the arguments themselves.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Often WARN is defined in data-centers as BUG and we would like to
avoid hanging the entire server on some internal error of the driver
(important as it might be).
Therefore, use dev_crit instead.
Signed-off-by: Alon Mizrahi <amizrahi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Instead of having it hard-coded as a define, pass it to the user
in runtime.
Signed-off-by: Moti Haimovski <mhaimovski@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In order to support the staged submission feature, user must be
allowed to use the same CS sequence for all submissions in the
same staged submission.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
As part of the staged submission feature, we need Gaudi to support
command submissions that will never get a completion.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In order for reserving VA ranges for kernel memory, we need
to allow the VM module to be initiated with kernel context.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
remove mmu_cache_lock as it protects a section which is already
protected by mmu_lock.
in addition, wrap mmu cache invalidate calls in hl_vm_ctx_fini with
mmu_lock.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Ofir Bitton