Upon encountering an unknown condition code, the script interpreter
is supposed to skip 'size' bytes and continue at the next devinit
token.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
It is not advisable to perform devinit if it has already been done.
VBIOS will very likely have invoked devinit if the GPU is the primary
graphics device, but there is no accurate way to detect this fact yet.
This patch adds such a method for gf100 and later chips, by means of the
NV_PTOP_SCRATCH1_DEVINIT_COMPLETED bit. This bit is set to 1 by devinit,
and reset to 0 when the GPU is powered.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We never use any nv50-specific member in this nv50_devinit_preinit().
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
nvkm_device_tegra_new initializes the irq member of the Tegra device
to -1 in order to signal that it is uninitialized. However,
nvkm_device_tegra_fini tests it against 0 to check whether an IRQ has
been allocated or not. This leads to free_irq being called on -1 during
device initialization.
Fix this by using 0 as the uninitialized value everywhere.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
nvkm_device_fini is never called if a failure occurs in
nvkm_device_init, even when unloading the module. This can lead to a
resources leak (one example is the Tegra interrupt which would never be
freed in that case). Fix this by calling nvkm_device_fini in
nvkm_device_init's failure path.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Use the nvkm_firmware_* functions when loading external firmware to
avoid duplicate code.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Add two functions nvkm_firmware_get() and nvkm_firmware_put() to load a
firmware file and free its resources, respectively. Since firmware files
are becoming a necessity for new GPUs, and their location has been
standardized to nvidia/chip/, this will prevent duplicate and
error-prone name-generation code.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Patch "ltc/gm107: use nvkm_mask to set cbc_ctrl1" sets the 3rd bit
of the CTRL1 register instead of writing it entirely in
gm107_ltc_cbc_clear(). As a counterpart, gm107_ltc_cbc_wait() must also
be modified to wait on that single bit only, otherwise a timeout may
occur if some other bit of that register is set. This happened at least
on GM206 when running glmark2-drm.
While we are at it, use the more compact nvkm_wait_msec() to wait for
the bit to clear.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The copy_from_user() function returns the number of bytes not copied but
we want to return a negative error code.
Fixes: 463873d570 ('drm/vc4: Add an API for creating GPU shaders in GEM BOs.')
Cc: stable@vger.kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
The original Raspberry Pi had the GPIO active high, but the later
models are active low. The DT GPIO bindings allow specifying the
active flag, except that it doesn't get propagated to the gpiodesc, so
you have to handle it yourself.
Signed-off-by: Eric Anholt <eric@anholt.net>
Tested-by: Daniel Stone <daniels@collabora.com>
Fixes an error thrown every few seconds when we poll HPD when it's on
a I2C to GPIO expander.
Signed-off-by: Eric Anholt <eric@anholt.net>
Tested-by: Daniel Stone <daniels@collabora.com>
The hardware provides us with separate threads for binning and
rendering, and the existing model waits for them both to complete
before submitting the next job.
Splitting the binning and rendering submissions reduces idle time and
gives us approx 20-30% speedup with some x11perf tests such as -line10
and -tilerect1. Improves openarena performance by 1.01897% +/-
0.247857% (n=16).
Thanks to anholt for suggesting this.
v2: Rebase on the spurious resets fix (change by anholt).
Signed-off-by: Varad Gautam <varadgautam@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
This pull request fixes the major VC4 HDMI modesetting bugs found when
the first wave of users showed up in Raspbian.
* tag 'drm-vc4-fixes-2016-03-03' of github.com:anholt/linux:
drm/vc4: Initialize scaler DISPBKGND on modeset.
drm/vc4: Fix setting of vertical timings in the CRTC.
drm/vc4: Fix the name of the VSYNCD_EVEN register.
drm/vc4: Add another reg to HDMI debug dumping.
drm/vc4: Bring HDMI up from power off if necessary.
drm/vc4: Fix a framebuffer reference leak on async flip interrupt.
562c5b4d89 didn't quite fix the issue of dealing with an error
pointer. We can't free/unref an error pointer so reset it to NULL.
Many thanks to Dan Carpenter for pointing this out again.
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Daniel Stone <daniels@collabora.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: dri-devel@lists.freedesktop.org
Fixes: 562c5b4d89 ("drm: fix blob pointer check")
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1457698646-22231-1-git-send-email-lionel.g.landwerlin@intel.com
SADs may span multiple CEA audio data blocks in the EDID.
CEA-861-E says:
"The order of the Data Blocks is not constrained. It is also possible
to have more than one of a specific type of data block if necessary to
include all of the descriptors needed to describe the sink’s capabilities."
Each audio data block can carry up to 10 SADs, whereas the ELD SAD limit
is 15 according to HDA 1.0a spec. So we should support at least two data
blocks. And apparently some devices take a more liberal interpretation
and stuff only one SAD per data block even when they would fit into one.
So let's try to extract all the SADs we can fit into the ELD even when
they span multiple data blocks.
While at it, toss in a comment to explain the 13 byte monitor name
string limit which confused me at first.
Cc: Arturo Pérez <artur999555@gmail.com>
Tested-by: Arturo Pérez <artur999555@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94197
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1457554066-8739-1-git-send-email-ville.syrjala@linux.intel.com
The commit d931589c01 ("drm/exynos: remove DRM_EXYNOS_GEM_MAP_OFFSET
ioctl") removed it same with the ioctl that this patch adds. The reason
that removed DRM_EXYNOS_GEM_MAP_OFFSET was we could use
DRM_IOCTL_MODE_MAP_DUMB. Both did exactly same thing.
Now we again will revive it as DRM_EXYNOS_GEM_MAP because of render
node. DRM_IOCTL_MODE_MAP_DUMB isn't permitted in render node.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Pull drm/i915 fixes from Dave Airlie:
"Just two i915 regression fixes, that should be it from me"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: Actually retry with bit-banging after GMBUS timeout
drm/i915: Fix bogus dig_port_map[] assignment for pre-HSW
Two i915 regression fixes.
* tag 'drm-intel-fixes-2016-03-11' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Actually retry with bit-banging after GMBUS timeout
drm/i915: Fix bogus dig_port_map[] assignment for pre-HSW
After the GMBUS transfer times out, we set force_bit=1 and
return -EAGAIN expecting the i2c core to call the .master_xfer
hook again so that we will retry the same transfer via bit-banging.
This is in case the gmbus hardware is somehow faulty.
Unfortunately we left adapter->retries to 0, meaning the i2c core
didn't actually do the retry. Let's tell the core we want one retry
when we return -EAGAIN.
Note that i2c-algo-bit also uses this retry count for some internal
retries, so we'll end up increasing those a bit as well.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: drm-intel-fixes@lists.freedesktop.org
Fixes: bffce907d6 ("drm/i915: abstract i2c bit banging fallback in gmbus xfer")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457366220-29409-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit 8b1f165a4a)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Code it similar to how we did it for the gfx and compute engines.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Check properly that the allocated blob's pointer is valid.
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Daniel Stone <daniels@collabora.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Daniel Stone <daniels@collabora.com>
Fixes: 5488dc16fd ("drm: introduce pipe color correction properties")
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1457611461-9116-1-git-send-email-lionel.g.landwerlin@intel.com
Pull drm fixes from Dave Airlie:
"A few imx fixes I missed from a couple of weeks ago, they still aren't
that big and fix some regression and a fail to boot problem.
Other than that, a couple of regression fixes for radeon/amdgpu, one
regression fix for vmwgfx and one regression fix for tda998x"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
Revert "drm/radeon/pm: adjust display configuration after powerstate"
drm/amdgpu/dp: add back special handling for NUTMEG
drm/radeon/dp: add back special handling for NUTMEG
drm/i2c: tda998x: Choose between atomic or non atomic dpms helper
drm/vmwgfx: Add back ->detect() and ->fill_modes()
drm/radeon: Fix error handling in radeon_flip_work_func.
drm/amdgpu: Fix error handling in amdgpu_flip_work_func.
drm/imx: Add missing DRM_FORMAT_RGB565 to ipu_plane_formats
drm/imx: notify DRM core about CRTC vblank state
gpu: ipu-v3: Reset IPU before activating IRQ
gpu: ipu-v3: Do not bail out on missing optional port nodes
Not needed any more because we need to protect the elements on the list anyway.
This reverts commit 38bf516c75b4ef0f5c716e05fa9baab7c52d6c39.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Not needed any more because we need to protect the elements on the list anyway.
This reverts commit fe237ed7efec8ac147a4572fdf81173a7f8ddda7.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Not needed any more because we need to protect the elements on the list anyway.
This reverts commit dae6ecf9e6c9b677e577826c3ac665c6dd9c490b.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We not only need to protect the mapping tree and freed list itself,
but also the items on those list.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Off-by-one: last is inclusive, so the maximum is start + max_size - 1
Wrong unit: addr is in bytes, max_size is in pages
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As observed on Apple iMac10,1, DCE-3.2, RV-730,
link rate of 2.7 Ghz is not selected, because
the args.v1.ucConfig flag setting for 2.7 Ghz
gets overwritten by a following assignment of
the transmitter to use.
Move link rate setup a few lines down to fix this.
In practice this didn't have any positive or
negative effect on display setup on the tested
iMac10,1 so i don't know if backporting to stable
makes sense or not.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Some PX laptops don't provide an ACPI method to control dGPU power. On
those systems, the driver is responsible for handling the dGPU power
state. Disable runtime PM on them until support for this is implemented.
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Some PX laptops don't provide an ACPI method to control dGPU power. On
those systems, the driver is responsible for handling the dGPU power
state. Disable runtime PM on them until support for this is implemented.
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Rename dma_*_writecombine() to dma_*_wc(), so that the naming
is coherent across the various write-combining APIs. Keep the
old names for compatibility for a while, these can be removed
at a later time. A guard is left to enable backporting of the
rename, and later remove of the old mapping defines seemlessly.
Build tested successfully with allmodconfig.
The following Coccinelle SmPL patch was used for this simple
transformation:
@ rename_dma_alloc_writecombine @
expression dev, size, dma_addr, gfp;
@@
-dma_alloc_writecombine(dev, size, dma_addr, gfp)
+dma_alloc_wc(dev, size, dma_addr, gfp)
@ rename_dma_free_writecombine @
expression dev, size, cpu_addr, dma_addr;
@@
-dma_free_writecombine(dev, size, cpu_addr, dma_addr)
+dma_free_wc(dev, size, cpu_addr, dma_addr)
@ rename_dma_mmap_writecombine @
expression dev, vma, cpu_addr, dma_addr, size;
@@
-dma_mmap_writecombine(dev, vma, cpu_addr, dma_addr, size)
+dma_mmap_wc(dev, vma, cpu_addr, dma_addr, size)
We also keep the old names as compatibility helpers, and
guard against their definition to make backporting easier.
Generated-by: Coccinelle SmPL
Suggested-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: airlied@linux.ie
Cc: akpm@linux-foundation.org
Cc: benh@kernel.crashing.org
Cc: bhelgaas@google.com
Cc: bp@suse.de
Cc: dan.j.williams@intel.com
Cc: daniel.vetter@ffwll.ch
Cc: dhowells@redhat.com
Cc: julia.lawall@lip6.fr
Cc: konrad.wilk@oracle.com
Cc: linux-fbdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Cc: luto@amacapital.net
Cc: mst@redhat.com
Cc: tomi.valkeinen@ti.com
Cc: toshi.kani@hp.com
Cc: vinod.koul@intel.com
Cc: xen-devel@lists.xensource.com
Link: http://lkml.kernel.org/r/1453516462-4844-1-git-send-email-mcgrof@do-not-panic.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Introduce PCI_VENDOR/PCI_SUBVENDOR/PCI_SUBDEVICE defines to replace the
constants scattered in the kernel already used to detect QEMU.
They are defined in the QEMU codebase per docs/specs/pci-ids.txt.
Signed-off-by: Robin H. Johnson <robbat2@gentoo.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- Fix ipu probe if optional port nodes are not present in the device tree
- Reset the ipu before initializing interrupts, not thereafter
- Notify DRM core about the state of vblank interrupts
- Add missing RGB565 format to the list of plate formats
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJWxs28AAoJEFDCiBxwnmDre0IP/3f3EaTmFP8bSzCW4rtEMn26
t5+frIRg/y7waM/BC5iK9jbi98oqKGdWB2kiaA8uS4jowS3AdD8wHN/9/W20onBF
BVrNbMELRSNqOTGxgjouO7FB/2FwvlKRZzFJlIQ4Xci/PFDkyVZ+Bhva+4L4kvNg
iHanmUM3nVsgCukefvkboVUJTfAkMsT1jd64Z8UDa+Bl6zsVsnzIUtHQKOzD6lwk
Pq+/d6l4B9dFbZLkhITI+A3N7GbjJ20SEjn+LOYehjTz8B3BWw9K5BvWndr2x6yX
/hTYSE2nVdsGOdZrwuYZY2pOocLvApme7raB8CSgsXzktZ+BBbDprsxae08ecGEg
qyekFuVGTrMzvpuBkMk16Phh6g7F2oTNzJ9mdR3c9J3Eoolc3d7ZVN9ZUtjqiCk5
XArrQMG9WbW9e6pFWIc3tpYRfybNN7oIEUAJnI7VKpeh56osIUXTCtXreyVxBDu6
ycKE4ZNsX2Fu+XhDk2enMtOdmNm32x1waR3vbKdIfJY0fjSd+N9FOt5SUXNlwzSX
NhLOLPYRorQ7cj72RvavEQCAtOywsoHWRLwdMDj4BAND1o4KcXzANb2ZwGH8awMk
beG8+0ZKM3HWzkhrpqti7StCrhWQNlmfkUgTu6/PX++m+SplII27cScKqFQZuFWm
M4YCzksuVhO6dgAT05zt
=9nEz
-----END PGP SIGNATURE-----
Merge tag 'imx-drm-fixes-2016-02-19' of git://git.pengutronix.de/git/pza/linux into drm-fixes
ipu-v3 probe and imx-drm crtc and plane fixes
- Fix ipu probe if optional port nodes are not present in the device tree
- Reset the ipu before initializing interrupts, not thereafter
- Notify DRM core about the state of vblank interrupts
- Add missing RGB565 format to the list of plate formats
* tag 'imx-drm-fixes-2016-02-19' of git://git.pengutronix.de/git/pza/linux:
drm/imx: Add missing DRM_FORMAT_RGB565 to ipu_plane_formats
drm/imx: notify DRM core about CRTC vblank state
gpu: ipu-v3: Reset IPU before activating IRQ
gpu: ipu-v3: Do not bail out on missing optional port nodes
radeon and amdgpu fixes for 4.5. Three regression fixes and
some fixups for the error handling in the vblank regression fixes
from earlier.
* 'drm-fixes-4.5' of git://people.freedesktop.org/~agd5f/linux:
Revert "drm/radeon/pm: adjust display configuration after powerstate"
drm/amdgpu/dp: add back special handling for NUTMEG
drm/radeon/dp: add back special handling for NUTMEG
drm/radeon: Fix error handling in radeon_flip_work_func.
drm/amdgpu: Fix error handling in amdgpu_flip_work_func.
Several cases of overlapping changes, as well as one instance
(vxlan) of a bug fix in 'net' overlapping with code movement
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
When I fixed the dp rate selection in:
3b73b168cffd9c392584d3f665021fa2190f8612
drm/amdgpu: fix dp link rate selection (v2)
I accidently dropped the special handling for NUTMEG
DP bridge chips. They require a fixed link rate.
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Ken Wang <Qingqing.Wang@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
When I fixed the dp rate selection in:
092c96a8ab
drm/radeon: fix dp link rate selection (v2)
I accidently dropped the special handling for NUTMEG
DP bridge chips. They require a fixed link rate.
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Ken Wang <Qingqing.Wang@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Tested-by: Ken Moffat <zarniwhoop@ntlworld.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If the allocation fails free memory and return error code.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Make the function free memory and return an error code if the allocation
fails.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If audio is disabled we shouldn't proceed into the fini function.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Updated DCEv11 afmt_init to cleanup if any kzalloc
fails and then return an error code. Don't continue initializing
the audio stack in that case.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Don't set config_init to true until all config statements pass.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If amdgpu_audio is disabled then the audio structure is not initialized
so we shouldn't read it in the fini function.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
That avoids lock inversion between the BO reservation lock
and the anon_vma lock.
v2:
* Changed amdgpu_bo_list_entry.user_pages to an array of pointers
* Lock mmap_sem only for get_user_pages
* Added invalidation of unbound userpointer BOs
* Fixed memory leak and page reference leak
v3 (chk):
* Revert locking mmap_sem only for_get user_pages
* Revert adding invalidation of unbound userpointer BOs
* Sanitize and fix error handling
v4 (chk):
* Init userpages pointer everywhere.
* Fix error handling when get_user_pages() fails.
* Add invalidation of unbound userpointer BOs again.
v5 (chk):
* Add maximum number of tries.
v6 (chk):
* Fix error handling when we run out of tries.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> (v4)
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Otherwise we might change the GDS settings while they are still in use.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
This allows us to use the pipeline sync for other tasks as well.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Switching the GDS space to often seems to be problematic.
This patch together with the following can avoid VM faults on context switch.
v2: extend commit message a bit
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com> (v1)
Reviewed-by: Chunming Zhou <david1.zhou@amd.com> (v1)
After all it's an operation on the VMID.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Try to avoid using the hardware specific fences even more.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
We need them all the time.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Not used any more since we now always use the sheduler.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
No need for two functions doing the same, remove one and
add comments what those functions actually do.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Remember the tasks which are inside get_user_pages()
and ignore MMU callbacks from there.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need them together with the next patch.
v2: Don't take bo reference twice
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
So that we can invalidate and flush the HDP independently
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's called after emitting ibs.
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Equivalent change to the radeon driver.
Note that with radeon this caught a bug in the dri3 DDX
implementation, which asked for vblank interrupts when the pipe is
off. That bug needs to be fixed before we can merge this patch (if
amdgpu is affected too). Michel discovered this one.
v2: agd: switch dce8 as well.
Acked-by: Michel Dänzer <michel.daenzer@amd.com>
Cc: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
These should be functionally equivalent to the older per/post modeset
functions, except that they block out drm_vblank_get right away.
There's only the clock adjusting code (outside of pageflips) in
readone which uses drm_vblank_get. But that code doesn't synchronize
against concurrent modesets and instead handles any such races by
waiting for the right vblank to arrive with a short timetout.
The longer-term plan here is to switch all kms drivers to
drm_vblank_on/off so that common code like pending event cleanup can
be done there, while drm_vblank_pre/post_modeset will be purely
drm internal for the old UMS ioctl.
Note that with this patch Michel uncovered a bug in the dri3
implementation of the DDX (it does vblank waits when the pipe is off),
which had to be fixed first.
Cc: Michel Dänzer <michel.daenzer@amd.com>
Acked-and-tested-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Looks like radeon commit:
d3052b8ce8
was missed.
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Ken Wang <Qingqing.Wang@amd.com>
Reviewed-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Looks like this got leftover by accident.
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Ken Wang <Qingqing.Wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This was leftover from a long time ago and is not longer needed
since the thermal controller setup code was added. Additional
mucking with the thermal interrupts can cause spurious thermal
events which can lead to unnecessary state changes.
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Ken Wang <Qingqing.Wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Patch based on a previous series by Shashank Sharma.
This introduces optional properties to enable color correction at the
pipe level. It relies on 3 transformations applied to every pixels
displayed. First a lookup into a degamma table, then a multiplication
of the rgb components by a 3x3 matrix and finally another lookup into
a gamma table.
The following properties can be added to a pipe :
- DEGAMMA_LUT : blob containing degamma LUT
- DEGAMMA_LUT_SIZE : number of elements in DEGAMMA_LUT
- CTM : transformation matrix applied after the degamma LUT
- GAMMA_LUT : blob containing gamma LUT
- GAMMA_LUT_SIZE : number of elements in GAMMA_LUT
DEGAMMA_LUT_SIZE and GAMMA_LUT_SIZE are read only properties, set by
the driver to tell userspace applications what sizes should be the
lookup tables in DEGAMMA_LUT and GAMMA_LUT.
A helper is also provided so legacy gamma correction is redirected
through these new properties.
v2: Register LUT size properties as range
v3: Fix round in drm_color_lut_get_value() helper
More docs on how degamma/gamma properties are used
v4: Update contributors
v5: Rename CTM_MATRIX property to CTM (Doh!)
Add legacy gamma_set atomic helper
Describe CTM/LUT acronyms in the kernel doc
v6: Fix missing blob unref in drm_atomic_helper_crtc_reset
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Kumar, Kiran S <kiran.s.kumar@intel.com>
Signed-off-by: Kausal Malladi <kausalmalladi@gmail.com>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Acked-by: Rob Bradford <robert.bradford@intel.com>
[danvet: CrOS maintainers are also happy with the userspacde side:
https://codereview.chromium.org/1182063002/ ]
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1456506302-640-4-git-send-email-lionel.g.landwerlin@intel.com
connector_state->crtc can no longer be unset by accident,
so that check can be removed. The other code open-codes
drm_atomic_get_existing_crtc_state, so use that.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Resolve tiny conflict due to gcc warning fix on previous
patch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that only encoders can be stolen that are part of the state
steal_encoder no longer needs to inspect all connectors,
just those that are part of the atomic state.
Changes since v1:
- Change return value to void, can no longer fail.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Appease gcc, reported by kbuild.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1456996662-8704-7-git-send-email-maarten.lankhorst@linux.intel.com
The current check doesn't handle the case where we don't steal an
encoder, but keep it on the current connector. If we repurpose
disable_conflicting_encoders to do the checking, we just have
to reject the ones that conflict.
Changes since v1:
- Return early with empty encoder_mask, drm_for_each_connector
requires connection_mutex held.
Changes since v2:
- Add comments for the loops.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Testcase: kms_setmode.invalid-clone-single-crtc-stealing
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1456996662-8704-6-git-send-email-maarten.lankhorst@linux.intel.com
Instead of failing with -EINVAL when conflicting encoders are found,
the legacy set_config will disable other connectors when encoders
conflict.
With the previous commit this becomes a lot easier to implement.
set_config only adds connectors to the state that are modified,
and because of the previous commit that calls add_affected_connectors
only on set->crtc it means any connector not part of the modeset can
be stolen from. We disable the connector in that case, and possibly
the crtc if required.
Atomic modeset itself still doesn't allow encoder stealing, the results
would be too unpredictable.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1456996662-8704-5-git-send-email-maarten.lankhorst@linux.intel.com
There's no need to have a separate function to get the crtc
which is stolen, this can already be found when actually
stealing the encoder.
drm_for_each_connector already checks for connection_mutex, so
use that macro now.
Changes since v1:
- Do not check for NULL crtc in connector_state,
this may happen when a crtc is disabled and its encoder stolen.
- Because of this, use connector->state->crtc instead of conn_state->crtc.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1456996662-8704-4-git-send-email-maarten.lankhorst@linux.intel.com
Choose between atomic or non atomic connector dpms helper. If tda998x
is connected to a drm driver that does not support atomic modeset
calling drm_atomic_helper_connector_dpms() causes a crash when the
connectors atomic state is not initialized. The patch implements a
driver specific connector dpms helper that calls
drm_atomic_helper_connector_dpms() if driver supports DRIVER_ATOMIC
and otherwise it calls the legacy drm_helper_connector_dpms().
Fixes commit 9736e988d3 ("drm/i2c: tda998x: Add support for atomic
modesetting").
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This partially reverts commit d56f57ac96 ("drm/gma500: Move to private
save/restore hooks") which removed these lines by mistake.
Reported-by: Sebastian Herbszt <herbszt@gmx.de>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thomas Hellstrom <thellstrom@vmware.com>
Tested-by: Sebastian Herbszt <herbszt@gmx.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some more radeon and amdgpu stuff for drm-next. Mostly just bug fixes
for new features and cleanups.
* 'drm-next-4.6' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: fix rb bitmap & cu bitmap calculation
drm/amdgpu: trace the pd_addr in vm_grab_id as well
drm/amdgpu: fix VM faults caused by vm_grab_id() v4
drm/amdgpu: update radeon acpi header
drm/radeon: update radeon acpi header
drm/amd: cleanup get_mfd_cell_dev()
drm/amdgpu: fix error handling in amdgpu_bo_list_set
drm/amd/powerplay: fix code style warning.
drm/amd: Do not make DRM_AMD_ACP default to y
drm/amdgpu/gfx: fix off by one in rb rework (v2)
Notable changes:
- correctness fixes to the GPU cache flushing when switching execution
state and when powering down the GPU
- reduction of time spent in hardirq-off context
- placement improvements to the GPU DMA linear window, allowing the
driver to properly work on i.MX6 systems with more than 2GB of RAM
* 'drm-etnaviv-next' of git://git.pengutronix.de/git/lst/linux:
drm: etnaviv: clean up submit_bo()
drm: etnaviv: clean up vram_mapping submission/retire path
drm: etnaviv: improve readability of command insertion to ring buffer
drm: etnaviv: clean up GPU command submission
drm: etnaviv: use previous GPU pipe state when pipe switching
drm: etnaviv: flush all GPU caches when stopping GPU
drm: etnaviv: track current execution state
drm: etnaviv: extract arming of semaphore
drm: etnaviv: extract replacement of WAIT command
drm: etnaviv: extract command ring reservation
drm/etnaviv: move GPU linear window to end of DMA window
drm/etnaviv: move runtime PM balance into retire worker
- fbc by default on hsw&bdw, thanks to great work by Paulo!
- psr by default hsw,bdw,vlv&chv, thanks to great work by Rodrigo!
- fixes to hw state readout vs. rpm issues (Imre)
- dc3 fixes&improvements (Mika), this and above already cherr-pick to -fixes
- first part of locking fixes from Tvrtko
- proper atomic code for load detect (Maarten)
- more rpm fixes from Ville
- more atomic work from Maarten
* tag 'drm-intel-next-2016-02-29' of git://anongit.freedesktop.org/drm-intel: (63 commits)
drm/i915: Update DRIVER_DATE to 20160229
drm/i915: Execlists cannot pin a context without the object
drm/i915: Reduce the pointer dance of i915_is_ggtt()
drm/i915: Rename vma->*_list to *_link for consistency
drm/i915: Balance assert_rpm_wakelock_held() for !IS_ENABLED(CONFIG_PM)
drm/i915/lrc: Only set RS ctx enable in ctx control reg if there is a RS
drm/i915/gen9: Set value of Indirect Context Offset based on gen version
drm/i915: Remove update_sprite_watermarks.
drm/i915: Kill off intel_crtc->atomic.wait_vblank, v6.
drm/i915: Unify power domain handling.
drm/i915: Pass crtc state to modeset_get_crtc_power_domains.
drm/i915: Add for_each_pipe_masked()
drm/i915: Make sure pipe interrupts are processed before turning off power well on BDW+
drm/i915: synchronize_irq() before turning off disp2d power well on VLV/CHV
drm/i915: Skip PIPESTAT reads from irq handler on VLV/CHV when power well is down
drm/i915/gen9: Write dc state debugmask bits only once
drm/i915/gen9: Extend dmc debug mask to include cores
drm/i915/gen9: Verify and enforce dc6 state writes
drm/i915/gen9: Check for DC state mismatch
drm/i915/fbc: enable FBC by default on HSW and BDW
...
Accumulated fixes and improvements from ti-linux-4.1.
* Almost complete rewrite of pagefliping code
* dma-buf support
* pinctrl support
* lot of fixes and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vIeq
-----END PGP SIGNATURE-----
Merge tag 'tilcdc-4.6' of https://github.com/jsarha/linux into drm-next
tilcdc changes for v4.6
Accumulated fixes and improvements from ti-linux-4.1.
* Almost complete rewrite of pagefliping code
* dma-buf support
* pinctrl support
* lot of fixes and cleanups
* tag 'tilcdc-4.6' of https://github.com/jsarha/linux: (22 commits)
drm/tilcdc: Use devm_kzalloc() and devm_kcalloc() for private data
drm/tilcdc: Initialize crtc->port
drm/tilcdc: Disable sync lost interrupt if it fires on every frame
drm/tilcdc: Add prints on sync lost and FIFO underrun interrupts
drm/tilcdc: Remove the duplicate LCDC_INT_ENABLE_SET_REG in registers[]
drm/tilcdc: Fix interrupt enable/disable code for version 2 tilcdc
drm/tilcdc: Do not update the next frame buffer close to vertical blank
drm/tilcdc: Get rid of complex ping-pong mechanism
drm/tilcdc: cleanup irq handling
drm/tilcdc: remove broken error handling
drm/tilcdc: split reset to a separate function
drm/tilcdc: disable crtc on unload
drm/tilcdc: cleanup runtime PM handling
drm/tilcdc: Allocate register storage based on the actual number registers
drm/tilcdc: fix build error when !CONFIG_CPU_FREQ
drm/tilcdc: Implement dma-buf support for tilcdc
drm/tilcdc: disable the lcd controller/dma engine when suspend invoked
drm/tilcdc: make frame_done interrupt active at all times
drm/tilcdc: fix kernel panic on suspend when no hdmi monitor connected
drm/tilcdc: adopt pinctrl support
...
This reverts commit dbb17a21c1.
It turns out that commit can cause problems for systems with multiple
GPUs, and causes X to hang on at least a HP Pavilion dv7 with hybrid
graphics.
This got noticed originally in 4.4.4, where this patch had already
gotten back-ported, but 4.5-rc7 was verified to have the same problem.
Alexander Deucher says:
"It looks like you have a muxed system so I suspect what's happening is
that one of the display is being reported as connected for both the
IGP and the dGPU and then the desktop environment gets confused or
there some sort problem in the detect functions since the mux is not
switched to the dGPU. I don't see an easy fix unless Dave has any
ideas. I'd say just revert for now"
Reported-by: Jörg-Volker Peetz <jvpeetz@web.de>
Acked-by: Alexander Deucher <Alexander.Deucher@amd.com>
Cc: Dave Airlie <airlied@gmail.com>
Cc: stable@kernel.org # wherever dbb17a21c1 got back-ported
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The recent commit [0bdf5a05647a: drm/i915: Add reverse mapping between
port and intel_encoder] introduced a reverse mapping to retrieve
intel_dig_port object from the port number. The code assumed that the
port vs intel_dig_port are 1:1 mapping. But in reality, this was a
too naive assumption.
As Martin reported about the missing HDMI audio on his SNB machine,
pre-HSW chips may have multiple intel_dig_port objects corresponding
to the same port. Since we assign the mapping statically at the init
time and the multiple objects override the map, it may not match with
the actually enabled output.
This patch tries to address the regression above. The reverse mapping
is provided basically only for the audio callbacks, so now we set /
clear the mapping dynamically at enabling and disabling HDMI/DP audio,
so that we can always track the latest and correct object
corresponding to the given port.
Fixes: 0bdf5a0564 ('drm/i915: Add reverse mapping between port and intel_encoder')
Reported-and-tested-by: Martin Kepplinger <martink@posteo.de>
Cc: drm-intel-fixes@lists.freedesktop.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1456324522-21591-1-git-send-email-tiwai@suse.de
(cherry picked from commit 9dfbffcf4a)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
As we now store the etnaviv_vram_mapping, we no longer need to store
the iova itself: we can get this directly from the mapping structure.
Arrange for submit_bo() to return a pointer to etnaviv_gem_submit_bo,
and directly access mapping->iova when applying relocations.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Currently, we scan the list of mappings each time we want to operate on
the vram_mapping struct. Rather than repeatedly scanning these, look
them up once in the submission path, and then use _reference and
_unreference methods as necessary to manage this object.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Improve the readibility of the function which inserts command buffers
and other maintanence commands into the GPUs ring buffer. We do this
by splitting the ring buffer reservation in two: one chunk for any
commands that need to be issued prior to the command buffer, and a
separate chunk for commands issued after the buffer.
The result is a much more obvious code flow in this function, and
localisation of the conditional maintanence commands prior to the
command buffer.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Clean up the GPU command submission path to prepare for the next change.
This makes the next change easier to read and understand.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Use the previous GPU pipe state when deciding which GPU caches should
be flushed prior to switching the current pipe. This avoids infering
what the previously selected pipe was, and potentially flushing the
wrong caches.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Flush the GPU caches to ensure that any dirty data is pushed out before
stopping the front end.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Add tracking of the current execution state (iow, active GPU pipe).
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Extract out the arming of a semaphore from the pipe select code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Extract out the replacement of the WAIT command with some other command.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Provide a helper etnaviv_buffer_reserve() to ensure that we can fit a
set of commands into the ring buffer without wrapping by moving code
out of etnaviv_buffer_queue().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
If the end of the system DMA window is farther away from the start of
physical RAM than the size of the GPU linear window, move the linear
window so that it ends at the same address than the system DMA window.
This allows to map command buffer from CMA, which is likely to reside
at the end of the system DMA window, while also overlapping as much
RAM as possible, in order to optimize regular buffer mappings through
the linear window.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
The retire worker is kicked for each fence, either the normal way
by signaling the fence from the event completion interrupt or by
the recover worker if the GPU got stuck. Moving the RPM put into
the retire worker allows us to have it in a single place for
both cases.
This also shaves off quite a bit of the CPU time spent in hardirq
context, as arming the autosuspend timer when the RPM refcount
drops to 0 is a relatively costly operation.
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
this do not mean driver error.
Change-Id: If2080eb4b79fc6389280b7c75cb7998d77090739
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
This is a port of the patch "drm/amdgpu: Fix error handling in amdgpu_flip_work_func."
to fix the following problem for radeon as well which was
reported against amdgpu:
The patch e1d09dc0ccc6: "drm/amdgpu: Don't hang in
amdgpu_flip_work_func on disabled crtc." from Feb 19, 2016, leads to
the following static checker warning, as reported by Dan Carpenter in
https://lists.freedesktop.org/archives/dri-devel/2016-February/101987.html
drivers/gpu/drm/amd/amdgpu/amdgpu_display.c:127 amdgpu_flip_work_func() warn: should this be 'repcnt == -1'
drivers/gpu/drm/amd/amdgpu/amdgpu_display.c:136 amdgpu_flip_work_func() error: double unlock 'spin_lock:&crtc->dev->event_lock'
drivers/gpu/drm/amd/amdgpu/amdgpu_display.c:136 amdgpu_flip_work_func() error: double unlock 'irqsave:flags'
This patch fixes both reported problems:
Change post-decrement of repcnt to pre-decrement, so
it can't underflow anymore, but still performs up to
three repetitions - three is the maximum one could
expect in practice.
Move the spin_unlock_irqrestore to where it actually
belongs.
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: <stable@vger.kernel.org> # 4.4+
Cc: Michel Dänzer <michel.daenzer@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The patch e1d09dc0ccc6: "drm/amdgpu: Don't hang in
amdgpu_flip_work_func on disabled crtc." from Feb 19, 2016, leads to
the following static checker warning, as reported by Dan Carpenter in
https://lists.freedesktop.org/archives/dri-devel/2016-February/101987.html
drivers/gpu/drm/amd/amdgpu/amdgpu_display.c:127 amdgpu_flip_work_func() warn: should this be 'repcnt == -1'
drivers/gpu/drm/amd/amdgpu/amdgpu_display.c:136 amdgpu_flip_work_func() error: double unlock 'spin_lock:&crtc->dev->event_lock'
drivers/gpu/drm/amd/amdgpu/amdgpu_display.c:136 amdgpu_flip_work_func() error: double unlock 'irqsave:flags'
This patch fixes both reported problems:
Change post-decrement of repcnt to pre-decrement, so
it can't underflow anymore, but still performs up to
three repetitions - three is the maximum one could
expect in practice.
Move the spin_unlock_irqrestore to where it actually
belongs.
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: <stable@vger.kernel.org> # 4.4+
Cc: Michel Dänzer <michel.daenzer@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
* HDMI interlace output support
* DMAbuf import support
* Big refactoring leading to removal of legacy code
* Various non-critical fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=+fwk
-----END PGP SIGNATURE-----
Merge tag 'omapdrm-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux into drm-next
omapdrm changes for v4.6
* HDMI interlace output support
* DMAbuf import support
* Big refactoring leading to removal of legacy code
* Various non-critical fixes
* tag 'omapdrm-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (76 commits)
drm/omap: no need to select OMAP2_DSS
drm/omap: gem: Fix omap_gem_new() error path
drm/omap: remove -Werror from Makefile
drm/omap: remove dispc_ovl_check()
drm/omap: remove dss compat code
drm/omap: remove last uses of omap_overlay_manager
drm/omap: DSI: remove uses of omap_overlay_manager
drm/omap: VENC: remove uses of omap_overlay_manager
drm/omap: SDI: remove uses of omap_overlay_manager
drm/omap: HDMI4: remove uses of omap_overlay_manager
drm/omap: HDMI5: remove uses of omap_overlay_manager
drm/omap: DPI: remove uses of omap_overlay_manager
drm/omap: remove extra manager checks on disconnect
drm/omap: remove extra check in dpi and sdi
drm/omap: convert dss_mgr_unregister_framedone_handler to accept omap_channel
drm/omap: convert dss_mgr_register_framedone_handler to accept omap_channel
drm/omap: convert dss_mgr_start_update to accept omap_channel
drm/omap: convert dss_mgr_disable to accept omap_channel
drm/omap: convert dss_mgr_enable to accept omap_channel
drm/omap: convert dss_mgr_set_lcd_config to accept omap_channel
...
Two small fixes that restore PRIME support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=u/CF
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-4.5-rc7' of git://anongit.freedesktop.org/tegra/linux into drm-fixes
drm/tegra: Fixes for v4.5-rc7
Two small fixes that restore PRIME support.
* tag 'drm/tegra/for-4.5-rc7' of git://anongit.freedesktop.org/tegra/linux:
gpu: host1x: Set DMA ops on device creation
gpu: host1x: Set DMA mask
Let's use __KERNEL_DIV_ROUND_UP, which is defined in uapi/linux/kernel.h.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch set nukes all the dummy crtc mode_fixup implementations.
(made on top of Daniel topic/drm-misc branch)
Signed-off-by: Carlos Palminha <palminha@synopsys.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch set nukes all the dummy crtc mode_fixup implementations.
(made on top of Daniel topic/drm-misc branch)
Signed-off-by: Carlos Palminha <palminha@synopsys.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch set nukes all the dummy crtc mode_fixup implementations.
(made on top of Daniel topic/drm-misc branch)
Signed-off-by: Carlos Palminha <palminha@synopsys.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the addition of crtc_state->connector_mask other connectors from
different crtc's aren't needed any more to determine if a crtc has
connectors, so only call add_affected_connectors on the target crtc.
This allows a cleanup to first remove all current connectors, then
add all set->connectors to the target crtc.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1456303053-28806-2-git-send-email-maarten.lankhorst@linux.intel.com
Currently host1x-instanciated devices have their dma_ops left to NULL,
which makes any DMA operation (like buffer import) on ARM64 fallback
to the dummy_dma_ops and fail with an error.
This patch calls of_dma_configure() with the host1x node when creating
such a device, so the proper DMA operations are set.
Suggested-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The default DMA mask covers a 32 bits address range, but host1x devices
can address a larger range on TK1 and TX1. Set the DMA mask to the range
addressable when we use the IOMMU to prevent the use of bounce buffers.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Small conflict as I had the balance in my tree already for testing.
* tag 'drm-intel-fixes-2016-03-03' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Balance assert_rpm_wakelock_held() for !IS_ENABLED(CONFIG_PM)
drm/i915/skl: Fix power domain suspend sequence
Big ticket items are hdmi support for 8996 (aka snapdragon 820), and
adreno 430 support. Also one more small uapi addition to support
timestamp queries.
* 'msm-next' of git://people.freedesktop.org/~robclark/linux: (29 commits)
drm/msm: rename hdmi symbols
drm/msm/adreno: remove duplicate adreno_hw_init() call
drm/msm: add timestamp param
drm/msm: fix small typo
drm/msm: grab struct_mutex after allocating submit
drm/msm: reject submit ioctl if no gpu
drm/msm/adreno: print details in case of a protect fault interrupt
drm/msm/adreno: get CP_RPTR from register instead of shadow memory
drm/msm/adreno: add adreno430 power control
drm/msm/adreno: support for adreno 430.
drm/msm: update generated headers
drm/msm/dsi: fix definition of msm_dsi_pll_28nm_8960_init()
drm/msm/dsi: Parse DSI lanes via DT
drm/msm/dsi: Drop VDD regulator for MSM8916
drm/msm/dsi: Remove incorrect warning on host attach
drm/msm: Free fb helper resources in msm_unload
drm/msm/mdp: Detach iommu in mdp4_destroy
drm/msm: make iommu port names const'ier
drm/msm/mdp: Use atomic helper to set crtc property
dt-bindings: msm/hdmi: Add HDMI PHY bindings
...
Global symbols in the kernel should be prefixed by the name
of the subsystem and/or driver to avoid conflicts when all
code is built-in.
In this case, function names like 'hdmi_register' or 'hdmi_set_mode'
are way too generic for an MSM specific DRM driver, so I'm renaming
them all to msm_hdmi_* here.
I also rename a lot of the 'static' symbols along with the global
names for consistency, even though those are relatively harmless;
they might only be slightly confusing when they show up in
backtraces.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Not sure where it came from, but seem unintentional. And also not
needed on a420, so let's just drop it.
Signed-off-by: Rob Clark <robdclark@gmail.com>
We need this for GL_TIMESTAMP queries.
Note: currently only supported on a4xx.. a3xx doesn't have this
always-on counter. I think we could emulate it with the one CP
counter that is available, but for now it is of limited usefulness
on a3xx (since we can't seem to do time-elapsed queries in any sane
way with the existing firmware on a3xx, and if you are trying to do
profiling on a tiler you want time-elapsed). We can add that later
if it becomes useful.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Existing userspace wouldn't get this far, since getparam ioctl would
have failed and it would have bailed out creating a screen/context.
But all the same, we shouldn't let evil or confused userspace cause a
null ptr deref.
Signed-off-by: Rob Clark <robdclark@gmail.com>
As described in the downstream/kgsl driver:
Sometimes the RPTR shadow memory is unreliable causing timeouts
in adreno_idle(). Read it directly from the register instead.
Signed-off-by: Craig Stout <cstout@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This fixes the following build failure:
drivers/gpu/drm/msm/dsi/pll/dsi_pll_28nm.o: In function `msm_dsi_pll_28nm_8960_init':
dsi_pll_28nm.c:(.text+0x1198): multiple definition of `msm_dsi_pll_28nm_8960_init'
drivers/gpu/drm/msm/dsi/pll/dsi_pll.o:dsi_pll.c:(.text+0x0): first defined here
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Acked-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The DSI driver is currently unaware of how the DSI physical data lanes
are mapped to the logical lanes provided by the DSI controller.
Create a DT binding "qcom,data-lane-map" that provides this information
on a given platform.
The MSM DSI controller is restricted in terms of what all mappings
it can support. The lane polarity is fixed for all the lanes, the clock
lanes are fixed, and the data lanes can be swapped among each other only
for a few combinations. Apply these restrictions when we parse the DT
data.
Cc: devicetree@vger.kernel.org
Cc: Rob Herring <robh@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
omapdss driver now depends on omapdrm, so we no longer should select
OMAP2_DSS from omapdrm's Kconfig.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When an error occurs in omap_gem_new() the function calls
omap_gem_free_object() to clean up. However, that function expects to be
called on a fully initialized GEM object and thus crashes.
Replace it by manual cleanup.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We have removed all the uses of compat code from omapdrm and the
non-compat parts of omapdss, so now we can remove all the compat code
itself.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We have now removed all uses of 'struct omap_overlay_manager', so we can
now remove the last places where it is set.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are removing the uses of 'struct omap_overlay_manager'. This patch
changes DSI driver to use 'omap_channel' instead.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are removing the uses of 'struct omap_overlay_manager'. This patch
changes VENC driver to use 'omap_channel' instead.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are removing the uses of 'struct omap_overlay_manager'. This patch
changes SDI driver to use 'omap_channel' instead.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are removing the uses of 'struct omap_overlay_manager'. This patch
changes HDMI4 driver to use 'omap_channel' instead.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are removing the uses of 'struct omap_overlay_manager'. This patch
changes HDMI5 driver to use 'omap_channel' instead.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are removing the uses of 'struct omap_overlay_manager'. This patch
changes DPI driver to use 'omap_channel' instead.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DSS output drivers check 'dssdev->manager' in disconnect()
functions. This check is not needed as the manager must always be set if
the output device was connected. Remove the check.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Both dpi and sdi check for 'mgr != NULL' in check_timings. This check is
not necessary, as mgr must always be set before check_timings. Remove
the check.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_unregister_framedone_handler() to accept 'enum
omap_channel' instead of 'struct omap_overlay_manager'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_register_framedone_handler() to accept 'enum
omap_channel' instead of 'struct omap_overlay_manager'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_start_update() to accept 'enum omap_channel' instead of
'struct omap_overlay_manager'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_disable() to accept 'enum omap_channel' instead of
'struct omap_overlay_manager'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_enable() to accept 'enum omap_channel' instead of
'struct omap_overlay_manager'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_set_lcd_config() to accept 'enum omap_channel' instead
of 'struct omap_overlay_manager'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_set_timings() to accept 'enum omap_channel' instead of
'struct omap_overlay_manager'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_disconnect() to accept 'enum omap_channel' instead of
'struct omap_overlay_manager'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_connect() to accept 'enum omap_channel' instead of
'struct omap_overlay_manager'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use 'out->dispc_channel_connected' to check if the device is connected
to an overlay manager or not, instead of using 'out->manager'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We want to remove the 'struct omap_overlay_manager' from
omap_dss_device. At the moment that field is used, among some other
uses, to see if the omap_dss_device is connected to an overlay manager.
To make it possible to remove the 'struct omap_overlay_manager' field,
this patch adds 'bool dispc_channel_connected' field to track the
connected-or-not status.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are removing the use of 'struct omap_overlay_manager' from omapdrm.
This patch changes the function pointers in 'dss_mgr_ops' to get 'enum
omap_channel' parameter instead of 'struct omap_overlay_manager'.
The change is very straightforward, as we still use 'struct
omap_overlay_manager' inside the function implementations where needed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In order to remove uses of 'struct omap_overlay_manager' we need to get
rid of using omapdss_find_mgr_from_display() when initializing omapdrm.
Instead of using omapdss_find_mgr_from_display() and mgr->id to find the
dispc channel used for the given display, we can instead use
omapdss_find_output_from_display(), and get the output->dispc_channel
from there.
We can also remove omapdss_find_mgr_from_display() as it's no longer
used.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In order to remove uses of 'struct omap_overlay_manager' from omapdrm,
this patch removes the crtc->mgr field.
To accomplish that, a new static array is added along the current
'omap_crtcs' static array, which is used to store the output device
connected to a crtc.
Optimally we'd use the struct omap_crtc to store this information, but
at the time when omap_crtc_dss_connect() is called, we don't yet have
the omap_crtc instances. This might possibly be fixed later, but for now
the static array does the job.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are removing the use of the 'struct omap_overlay_manager' from
omapdrm, and one part of that is removing the use of
mgr->supported_outputs field.
This patch adds dispc_mgr_get_supported_outputs() function which can be
used instead of mgr->supported_outputs. omap_crtc.c is changed to use
the new function.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch continues the work to create private versions of the
omapdss.h header for omapdrm and omapfb. This one moves the dss_mgr_*
function declarations.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch continues the work to create private versions of the
omapdss.h header for omapdrm and omapfb. This one moves 'struct dss_mgr_ops'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapdrm and omapfb still share the same include/video/omapdss.h. We need
to change that so that we can proceed with omapdrm work.
However, it's not trivial to make separate omapfb and omapdrm versions
of omapdss.h, as that file is also included in other places like arch
code, audio code and omap_vout code. So we'll do it piece by piece.
This patch makes private versions of all the dispc function declarations
that are in omapdss.h. For omapdrm we create a new file,
drivers/gpu/drm/omapdrm/dss/omapdss.h, which will contain headers meant
to be visible outside omapdss.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We no longer have any boards that require the platform data support from
the panel, so we can remove the related code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We no longer have any boards that require the platform data support from
the panel, so we can remove the related code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We no longer have any boards that require the platform data support from
the panel, so we can remove the related code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We no longer have any boards that require the platform data support from
the panel, so we can remove the related code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We no longer have any boards that require the platform data support from
the panel, so we can remove the related code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We no longer have any boards that require the platform data support from
the connector, so we can remove the related code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We no longer have any boards that require the platform data support from
the connector, so we can remove the related code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We no longer have any boards that require the platform data support from
the encoder, so we can remove the related code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We no longer have any boards that require the platform data support from
the panel, so we can remove the related code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
core.c is the only caller of dss_disable_all_devices(). We can thus move
the function from display.c to core.c and make it static.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
For legacy reasons omapdss handles system suspend/resume via PM notifier
callback, where the driver disables/resumes all the outputs.
This doesn't work well with omapdrm. What happens on suspend is that the
omapdss disables the displays while omapdrm is still happily continuing
its work, possibly waiting for an vsync irq, which will never come if
the display output is disabled, leading to timeouts and errors sent to
userspace.
This patch moves the suspend/resume handling to omapdrm, and the
suspend/resume is now done safely inside modeset lock.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapdrm is missing a check on the validity of the rotation property.
This leads to omapdrm possibly trying to use rotation on non-rotateable
framebuffer, which causes the overlay setup to fail.
This patch adds the necessary check to omap_plane_atomic_check().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Before universal planes we had to have plane specific properties for the
crtc too, as on the hardware level a crtc uses a plane. In other words,
e.g. 'zorder' property was added to both planes and crtcs, and
omap_crtc.c would delegate the property set/get to the primary plane.
However, the delegation was a bit too generic, delegating all property
set/get calls to planes. Thus it's possible to set, say, FB_ID, on a
crtc, which gets redirected to the primary plane.
This is not standard, and shouldn't be allowed. To keep backward
compatibility, we still need to redirect the properties we supported
earlier for crtcs, namely 'zorder' and 'rotation'.
This patch redirects only the allowed properties from crtcs to planes.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Subsequent threads returning EBUSY from vm_insert_pfn() was not
handled correctly. As a result concurrent access from new threads
to mmapped data caused SIGBUS.
See e79e0fe380 ("drm/i915: EBUSY status
handling added to i915_gem_fault()").
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The DSS hardware uses the same ROW_INC value for both Y and UV planes
for NV12 format. This means that the pitches of the Y and UV planes have
to match. omapdrm doesn't check this at the moment, and this can lead
into a broken NV12 fb on the screen.
This patch adds the check.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
DISPC requires the x resolution to be divisible by 8 when stall mode is
not used.
Add a check to the DPI driver to verify this.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Now that interlace support has been added, we can remove the check that
prevents interlace.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Add the missing bits for interlace:
* Set VBLANK_OSC if the videomode's vblank is fractional
* Halve the vertical timings for interlace
* Double the horizontal timings for double-pixel mode
* Set FC_PRCONF properly for double-pixel mode
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The HDMI driver copies the timing values one by one. Instead we can just
copy the whole struct.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
For some reason the HDMI FC's HSW value is programmed to hsw-1. There's
no indication in the documentation that this would be correct, and no
other blanking value needs -1 either.
So remove the -1.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Interlace field order is different between VENC and HDMI. The driver
currently sets the field order for VENC.
This patch adds the code to set the field order for HDMI.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The HDMI WP timings are not programmed correctly for interlace.
We need to halve the vertical timings when interlace is used, and double
the horizontal timings when pixel doubling is used.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
On OMAP4 and OMAP5 ES1.0 the HDMI_WP_VIDEO_TIMING_H:HSW field is
set directly to the HSW value. On later SoCs the field needs to be
programmed with the value of HSW-1.
Currently the driver always programs the field with the HSW value. Most
videomodes seem to work fine with that, but at least low resolution
interlaced modes don't work at all.
This patch fixes the HSW for OMAP5 ES2.0+ SoCs.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We need double-pixel mode (pixel repetition) for interlace modes. This
patch adds the necessary support to HDMI to double the pixel clock when
double-pixel mode is used.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We need double-pixel mode (pixel repetition) for interlace modes. This
patch adds the necessary support to omapdrm to output double-pixel mode.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We need double-pixel mode (pixel repetition) for interlace modes. This
patch adds the necessary support to DISPC to output double-pixel mode.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
omap_crtc_wait_pending() waits until the config changes have been taken
into use, usually at next vblank. The wait-timeout used is 50ms, which
usually is enough, but in some rare cases not.
As time wait-timeout is just a safety measure for cases where something
is broken, we can just as well increase the timeout considerably.
This patch makes the timeout 250ms.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We no longer have the omapdrm plugin system for SGX, and we can thus
remove the support for external memory and sync objects from omap_gem.c.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
OMAP GEM objects backed by dma_buf reuse the current OMAP GEM object
support as much as possible. If the imported buffer is physically
contiguous its physical address will be used directly, reusing the
OMAP_BO_MEM_DMA_API code paths. Otherwise it will be mapped through the
TILER using a pages list created from the scatterlist instead of the
shmem backing storage.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Split the individual steps of GEM object allocation and initialization
clearly. This improves readability and prepares for dma_buf import
support.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The driver assumes that only objects backed by shmem need to be mapped
through DMM. While this is true with the current code, the assumption
won't hold with dma_buf import support.
Condition the mapping based on whether the buffer has been allocated
using the DMA mapping API instead and clean up the flags to avoid having
to check both flags and GEM object filp field to decide how to process
buffers. Flags are not the authoritative source of information regarding
where the buffer memory comes from, and are renamed to make that
clearer.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If the panel's enable fails, omap_encoder silently ignores the failure.
omapdrm should really handle the failure, but unfortunately the whole
encoder enable codepath is expected to always succeed.
So for now, catch the enable failure and print an error.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
omap_gem_dma_sync() calls dma_map_page() but does not check the possible
error with dma_mapping_error(). If DMA-API debugging is enabled, the
debug layer will give a warning if dma_mapping_error() has not been
used.
This patch adds proper error handling to omap_gem_dma_sync().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
omap_gem_attach_pages() calls dma_map_page() but does not check the
possible error with dma_mapping_error(). If DMA-API debugging is
enabled, the debug layer will give a warning if dma_mapping_error() has
not been used.
This patch adds proper error handling to omap_gem_attach_pages().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
tpd12s015 HW has LS_OE, CT_CP_HPD and HPD gpios. Out of these gpios,
driver only handled LS_OE as optional. The CT_CP_HPD gpio should also
be treated as optional gpio as it is just a power saving feature. Some
boards hardwire this gpio to be always enable. In this patch, all access
to CT_CP_HPD gpio is made optional.
Signed-off-by: Manisha Agrawal <manisha.agrawal@ti.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
All devices using tpd12s015 driver are doing DT boot. No need of further
supporting the platform data. This patch removes support for platform
data.
Signed-off-by: Manisha Agrawal <manisha.agrawal@ti.com>
[tomi.valkeinen@ti.com: minor adjustments]
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
This patch adds wrapper functions for readl() and writel(), dmm_read()
and dmm_write(), so that we can implement workaround for DRA7 errata
i878.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The current driver uses non-blocking DMM fill when releasing memory.
This gives us a small performance increase as we don't have to wait for
the fill operation to finish.
However, the driver does not have any error handling for non-blocking
fill. In case of an error, the fill operation may silently fail, leading
to leaking DMM engines, which may eventually lead to deadlock if we run
out of DMM engines.
This patch makes the DMM driver always use blocking fills, so that we
can catch the errors. A more complex option would be to allow
non-blocking fills, and implement proper error handling, but that is
left for the future.
This patch is a HACK, as the proper fix is to either decide to always
use sync fills and remove all the async related code, or fix the async
code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We occasionally see DISPC sync-lost errors when enabling and disabling
HDMI. Sometimes we get only a few, which get handled (ignored) by the
driver, but sometimes there's a flood of the errors which doesn't seem
to stop.
The HW team has root caused this to the order in which HDMI and DISPC
are enabled/disabled. Currently we enable HDMI first, and then DISPC,
and vice versa when disabling. HW team's suggestion is to do it the
other way around.
This patch changes the order, but this has two side effects as the pixel
clock is produced by HDMI, and the clock is not running when we
enable/disable DISPC:
* When enabling DISPC first, we don't get vertical sync events
* When disabling DISPC last, we don't get FRAMEDONE event
At the moment we use both of those to verify that DISPC has been
enabled/disabled properly. Thus this patch also needs to change the
omapdrm and omapdss which handle the DISPC side.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The STi drm driver correctly warns about invalid format strings
when built with 64-bit dma_addr_t:
sti_hqvdp.c: In function 'sti_hqvdp_vtg_cb':
sti_hqvdp.c:605:119: warning: format '%x' expects argument of type
'unsigned int', but argument 5 has type 'dma_addr_t {aka long long
unsigned int}' [-Wformat=]
sti_hqvdp.c: In function 'sti_hqvdp_atomic_update':
sti_hqvdp.c:931:118: warning: format '%x' expects argument of type
'unsigned int', but argument 5 has type 'dma_addr_t {aka long long
unsigned int}' [-Wformat=]
This could be changed to using the %pad format string, but that
does not work when printing an rvalue, so instead I'm changing
the type in the sti_hqvdp structure to u32, which is what gets
written into the registers anyway.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Vincent Abriou <vincent.abriou@st.com>
Thanks to "drm: prime: Honour O_RDWR during prime-handle-to-fd"
commit we don't need to hack flags anymore.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix some copy paste typos.
Signed-off-by: Flora Cui <Flora.Cui@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes for radeon and amdgpu:
- Fix GPUVM flushing on CI and VI
- Misc DPM and Powerplay fixes
- VCE DPM fixes for CZ/ST
- DP hotplug fix
* 'drm-fixes-4.5' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: return from atombios_dp_get_dpcd only when error
drm/amdgpu/cz: remove commented out call to enable vce pg
drm/amdgpu/powerplay/cz: enable/disable vce dpm independent of vce pg
drm/amdgpu/cz: enable/disable vce dpm even if vce pg is disabled
drm/amdgpu/gfx8: specify which engine to wait before vm flush
drm/amdgpu: apply gfx_v8 fixes to gfx_v7 as well
drm/amd/powerplay: send event to notify powerplay all modules are initialized.
drm/amd/powerplay: export AMD_PP_EVENT_COMPLETE_INIT task to amdgpu.
drm/radeon/pm: update current crtc info after setting the powerstate
drm/amdgpu/pm: update current crtc info after setting the powerstate
VDD regulator input was specified for MSM8916. It turns our that this
regulator is used for the display panels used on MSM8916 platforms, but
not the DSI controller itself. Drop this regulator from the list.
Reported-by: Vinay Simha <vinaysimha@inforcecomputing.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
With the implementation of of_graph parsing, it isn't any longer
necessary for msm_host->device node to be same as dsi->dev.of_node. This
only holds true when the connected device is also a child of the dsi_host.
In the case of external bridge chips belonging to a different control
bus, these are guaranteed to be different.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We have a msm_fbev_free function to uninit fb_helper stuff, but we aren't
using it. Call it in msm_unload.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
attach_dev gets called in mdp4_kms_init, but there is no corresponding
detach_dev called in the error path or in the kms driver unload path.
Detach and destroy mmu in mdp4_destroy.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Assign drm_atomic_helper_crtc_set_property helper to MDP4 and MDP5
crtcs' set_property ops. This replaces the custom funcs that
returned an error even for standard crtc properties.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Instead of forcing bridges to implement empty callbacks make them all
optional.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for United Radiant Technology UMSH-8596MD-xT 7.0" WVGA TFT
LCD panels in the simple-panel driver.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The LG lp120up1 TFT LCD panel with eDP interface is a 12.0" 1920x1280
panel, which can be supported by the simple panel driver.
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Set hsync/vsync to active low for g121x1_l03 panel to match the
recommended setting in the datasheet.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
MIPI DSI devices are inherently aware of their host because they share a
parent-child hierarchy in the device tree.
Non-DSI drivers that create DSI device don't have this data. In order to
get this information, they require to a phandle to the DSI host in the
device tree.
Maintain a list of all the DSI hosts that are currently registered. This
list will be used to find the struct mipi_dsi_host corresponding to the
device tree node passed to of_find_mipi_dsi_host_by_node().
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
A driver calling mipi_dsi_device_register_full() might want to remove
the device once it's done. It might also require it in an error handling
path in case something went wrong.
Create mipi_dsi_device_unregister() for this purpose and use it within
mipi_dsi_remove_device_fn() as it does the same thing.
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In amdgpu_connector_hotplug(), we need to start DP link
training only after we have received DPCD. The function
amdgpu_atombios_dp_get_dpcd() returns non-zero value only
when an error condition is met, otherwise returns zero.
So in case the function encounters an error, we need to
skip rest of the code and return from amdgpu_connector_hotplug()
immediately. Only when we are successfull in reading DPCD
pin, we should carry on with turning-on the monitor.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This code path is not currently enabled now that we properly
respect the vce pg flags, so uncomment the actual pg calls
so the code is as it should be we are eventually able to
enable vce pg.
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If we don't disable it when vce is not in use, we use extra power
if vce pg is disabled.
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
I missed this when cleaning up the vce pg handling.
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Select between me and pfp properly.
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We never ported that back to CIK, so we could run into VM faults here.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
with this event, powerplay can adjust current power state if needed.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
This is needed to init the dynamic states without a display. To be
used in the next commit.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
On CI, we need to see if the number of crtcs changes to determine
whether or not we need to upload the mclk table again. In practice
we don't currently upload the mclk table again after the initial load.
The only reason you would would be to add new states, e.g., for
arbitrary mclk setting which is not currently supported.
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
On CI, we need to see if the number of crtcs changes to determine
whether or not we need to upload the mclk table again. In practice
we don't currently upload the mclk table again after the initial load.
The only reason you would would be to add new states, e.g., for
arbitrary mclk setting which is not currently supported.
Acked-by: Jordan Lazare <Jordan.Lazare@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Add a device name field in struct mipi_dsi_device. This name is not the
same as the device name (which is of the format "hostname.reg"). When
the device is created via DT, this name is set to the modalias string.
In the non-DT case, the driver creating the DSI device provides the
name by populating a field in struct mipi_dsi_device_info.
Matching for DT case would be as it was before. For the non-DT case, we
compare the device and driver names. Other buses (like I2C/SPI) perform
a non-DT match by comparing the device name and entries in the driver's
id_table. Such a mechanism isn't used for the DSI bus.
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use mipi_dsi_device_register_full() for device creation. This takes in
a struct mipi_dsi_device_info as a template to populate the DSI device
information.
The reason to introduce this is to have a way to create DSI devices not
available via DT. Drivers that want to create a DSI device can populate
a struct mipi_dsi_device_info and call this function. For DSI devices
available via DT, of_mipi_dsi_device_add() is used as before, but this
now calls mipi_dsi_device_register_full() internally.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Ben Skeggs