Some of the w/a or different behavior of userspace blob driver seem to
be keyed to gpu patch revision, rather than gpu-id. So expose the full
chip-id to userspace so it can DTRT.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Shut down the clks when the gpu has nothing to do. A short inactivity
timer is used to provide a low pass filter for power transitions.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Merge "qcom driver changes for v3.15" from Kumar Gala:
We've split Qualcomm MSM support into legacy and multiplatform. These
drivers are only relevant on the multiplatform supported SoCs so switch the
Kconfig depends to ARCH_QCOM.
* tag 'qcom-drivers-for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
gpio: msm: switch Kconfig to ARCH_QCOM depends
hwrng: msm: switch Kconfig to ARCH_QCOM depends
power: reset: msm - switch Kconfig to ARCH_QCOM depends
drm/msm: drop ARCH_MSM Kconfig depend
tty: serial: msm: Enable building msm_serial for ARCH_QCOM
The ARCH_MSM depend is redundant with ARCH_MSM8960, so we can remove it.
Additionally, we are splitting Qualcomm MSM support into legacy (ARCH_MSM)
and multiplatform (ARCH_QCOM). The MSM8960 with be ARCH_QCOM going forward
so dropping ARCH_MSM will work properly for the new ARCH_QCOM multiplatform
build.
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Compared to original fixes pull req that I sent yesterday, this adds
one more fix that I found for a synchronization issue which starts to
crop up when we use XA in DDX for 2d accel on 3d core. In particular,
accelerating presentation blit triggers this problem.
* 'msm-next' of git://people.freedesktop.org/~robclark/linux:
drm/msm: bigger synchronization hammer
drm/msm: fix deadlock in bo create fail path
drm/msm/mdp4: cursor fixes
drm/msm/mdp4: pageflip fixes
drm/msm/mdp5: fix ref leaks in error paths
drm/msm: fix inconsequential typo
Because we use a list_head in the bo to track it's position in a submit,
we need to serialize at a higher layer. Otherwise there are problems
when multiple contexts are SUBMIT'ing in parallel cmdstreams referencing
a shared bo.
Signed-off-by: Rob Clark <robdclark@gmail.com>
It seems we need to update all cursor registers from vblank. This
appears to be the cause of intermittent underflows when enabling/
disabling cursor.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Backport a few fixes found in the course of getting mdp5 working.
There is a window of time after pageflip is requested, before we
start scanning out the new fb (ie. while we are waiting for gpu).
During that time we need to continue holding a reference to the
still-current scanout fb, to avoid the backing gem bo's from being
destroyed.
Possibly a common mdp_crtc parent class could be useful to share
some of this logic between mdp4_crtc and mdp5_crtc. OTOH, this
all can be removed from the driver once atomic is in place, as
plane/crtc updates get deferred until all fb's are ready before
calling in to .page_flip(), etc.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Small typo I noticed in the mdp4_plane code.. no consequence because
PIPE_SRC_XY and PIPE_DST_XY have same register layout.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Pull drm updates from Dave Airlie:
"Been a bit busy, first week of kids school, and waiting on other trees
to go in before I could send this, so its a bit later than I'd
normally like.
Highlights:
- core:
timestamp fixes, lots of misc cleanups
- new drivers:
bochs virtual vga
- vmwgfx:
major overhaul for their nextgen virt gpu.
- i915:
runtime D3 on HSW, watermark fixes, power well work, fbc fixes,
bdw is no longer prelim.
- nouveau:
gk110/208 acceleration, more pm groundwork, old overlay support
- radeon:
dpm rework and clockgating for CIK, pci config reset, big endian
fixes
- tegra:
panel support and DSI support, build as module, prime.
- armada, omap, gma500, rcar, exynos, mgag200, cirrus, ast:
fixes
- msm:
hdmi support for mdp5"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (595 commits)
drm/nouveau: resume display if any later suspend bits fail
drm/nouveau: fix lock unbalance in nouveau_crtc_page_flip
drm/nouveau: implement hooks for needed for drm vblank timestamping support
drm/nouveau/disp: add a method to fetch info needed by drm vblank timestamping
drm/nv50: fill in crtc mode struct members from crtc_mode_fixup
drm/radeon/dce8: workaround for atom BlankCrtc table
drm/radeon/DCE4+: clear bios scratch dpms bit (v2)
drm/radeon: set si_notify_smc_display_change properly
drm/radeon: fix DAC interrupt handling on DCE5+
drm/radeon: clean up active vram sizing
drm/radeon: skip async dma init on r6xx
drm/radeon/runpm: don't runtime suspend non-PX cards
drm/radeon: add ring to fence trace functions
drm/radeon: add missing trace point
drm/radeon: fix VMID use tracking
drm: ast,cirrus,mgag200: use drm_can_sleep
drm/gma500: Lock struct_mutex around cursor updates
drm/i915: Fix the offset issue for the stolen GEM objects
DRM: armada: fix missing DRM_KMS_FB_HELPER select
drm/i915: Decouple GPU error reporting from ring initialisation
...
This was hidden in a generic void * dev->mm_private. But only ever
used for gem. But thanks to this fake generic pretension no one
noticed that Rob's drm drivers are now all broken.
So just give the offset manager a type pointer and fix up msm, omapdrm
and tilcdc.
v2: Fixup compile fail.
v3: Fixup rebase fail that David spotted.
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add support for adreno 330. Not too much different, just a few
differences in initial configuration plus setting OCMEM base.
Userspace support is already in upstream mesa.
Note that the existing DT code is simply using the bindings from
downstream android kernel, to simplify porting of this driver to
existing devices. These do not constitute any committed/stable
DT ABI. The addition of proper DT bindings will be a subsequent
patch, at which point (as best as possible) I will try to support
either upstream bindings or what is found in downstream android
kernel, so that existing device DT files can be used.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add support for the new MDP5 display controller block. The mapping
between parts of the display controller and KMS is:
plane -> PIPE{RGBn,VIGn} \
crtc -> LM (layer mixer) |-> MDP "device"
encoder -> INTF /
connector -> HDMI/DSI/eDP/etc --> other device(s)
Unlike MDP4, it appears we can get by with a single encoder, rather
than needing a different implementation for DTV, DSI, etc. (Ie. the
register interface is same, just different bases.)
Also unlike MDP4, all the IRQs for other blocks (HDMI, DSI, etc) are
routed through MDP.
And finally, MDP5 has this "Shared Memory Pool" (called "SMP"), from
which blocks need to be allocated to the active pipes based on fetch
stride.
Signed-off-by: Rob Clark <robdclark@gmail.com>
The HDMI block is basically the same between older SoC's with mdp4
display controller, and newer ones with mdp5.
So mostly this consists of better abstracting out the different sets of
regulators, clks, etc. In particular, for regulators and clks we can
split it up by what is needed for hot plug detect to work, and what is
needed to light up the display.
Also, 8x74 has a new phy.. a very simple one, but split out into a
different mmio space. And with mdp5, the irq is shared with mdp, so we
don't directly register our own irq handler.
Signed-off-by: Rob Clark <robdclark@gmail.com>
This can be shared between mdp4 and mdp5. Both use the same set of
parameters to describe the format to the hw.
Signed-off-by: Rob Clark <robdclark@gmail.com>
There are some little bits and pieces that mdp4 and mdp5 can share, so
move things around so that we can have both in a common parent
directory.
Signed-off-by: Rob Clark <robdclark@gmail.com>
This adds the necessary configuration for the APQ8060A SoC (dual-core
krait + a320 gpu) as found on the bstem board.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add a VRAM carveout that is used for systems which do not have an IOMMU.
The VRAM carveout uses CMA. The arch code must setup a CMA pool for the
device (preferrably in highmem.. a 256m-512m VRAM pool in lowmem is not
cool). The user can configure the VRAM pool size using msm.vram module
param.
Technically, the abstraction of IOMMU behind msm_mmu is not strictly
needed, but it simplifies the GEM code a bit, and will be useful later
when I add support for a2xx devices with GPUMMU, so I decided to keep
this part.
It appears to be possible to configure the GPU to restrict access to
addresses within the VRAM pool, but this is not done yet. So for now
the GPU will refuse to load if there is no sort of mmu. Once address
based limits are supported and tested to confirm that we aren't giving
the GPU access to arbitrary memory, this restriction can be lifted
Signed-off-by: Rob Clark <robdclark@gmail.com>
This got a bit broken with original patches when re-arranging things to
move dependencies on mach-msm inside #ifndef OF.
Signed-off-by: Rob Clark <robdclark@gmail.com>
The DRM driver for MSM depends on symbols from the MSM
IOMMU driver. Add this dependency to the Kconfig file.
Fixes this comile error:
Kernel: arch/arm/boot/zImage is ready
ERROR: "msm_iommu_get_ctx" [drivers/gpu/drm/msm/msm.ko]
undefined!
make[2]: *** [__modpost] Error 1
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
I've killed them a long time ago in drm/i915, let's get rid of this
remnant of shared drm core days for good.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The drvdata pointer is already assigned to something useful.
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
prime support, inactive rework, render nodes
* 'msm-next' of git://people.freedesktop.org/~robclark/linux:
drm/msm/mdp4: page_flip cleanups/fixes
drm/msm: EBUSY status handling in msm_gem_fault()
drm/msm: rework inactive-work
drm/msm: add plane support
drm/msm: resync generated headers
drm/msm: support render nodes
drm/msm: prime support
There were a few potential problems with the original page_flip/vblank
code in mdp4_crtc.
1) We need vblank irq for a couple things, both completing flips and
updating cursor. We need to keep track of what work is pending so
that (for example) a cursor update while we are still waiting for
pageflip_cb (ie. pageflip requested from userspace, but still
waiting for rendering to complete) would not prematurely trigger
event to userspace.
2) A preclose -> pageflip-cancel should not cancel a pageflip that
was requested on a different file (ie. non-master closing should
not cancel a pending pageflip).
With these fixes, we no longer have problems w/ cursor not updating and
with occasional hangs with userspace waiting for a pageflip that had
been cancelled (launching XBMC from gnome-shell overview mode was a good
way to trigger this, but now works reliably).
Signed-off-by: Rob Clark <robdclark@gmail.com>
Subsequent threads returning EBUSY from vm_insert_pfn() was not
handled correctly. As a result concurrent access from new threads
to mmapped data caused SIGBUS.
See e79e0fe3
Signed-off-by: Rob Clark <robdclark@gmail.com>
Acked-by: David Brown <davidb@codeaurora.org>
Re-arrange things a bit so that we can get work requested after a bo
fence passes, like pageflip, done before retiring bo's. Without any
sort of bo cache in userspace, some games can trigger hundred's of
transient bo's, which can cause retire to take a long time (5-10ms).
Obviously we want a bo cache.. but this cleanup will make things a
bit easier for atomic as well and makes things a bit cleaner.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Acked-by: David Brown <davidb@codeaurora.org>
Enable using VG1 and VG2 for planes. Currently YUV/CSC or scaling is
not enabled, but ARGB and xRGB blending is.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Acked-by: David Brown <davidb@codeaurora.org>
Enable support for drm render nodes for msm by flagging the ioctls
that are safe and only needed for rendering.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Acked-by: David Brown <davidb@codeaurora.org>
For drivers which might want to disable fbdev legacy support.
Select the new option in all drivers for now, so this shouldn't result
in any change. Drivers need some work anyway to make fbdev support
optional (if they have it implemented, that is), so the recommended
way to expose this is by adding per-driver options. At least as long
as most drivers don't support disabling the fbdev support.
v2: Update for new drm drivers msm and rcar-du. Note that Rob's msm
driver can already take advantage of this, which allows us to build
msm without any fbdev depencies in the kernel!
v3: Move the MODULE_* stuff from the fbdev helper file to
drm_crtc_helper.c.
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Acked-by: Dave Airlie <airlied@linux.ie>
Reviewed-by: Chon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We still need an API exported by msm iommu driver (but not visible in
any public header anymore). For now, just declare the prototype
ourselves, but when msm iommu driver provides a better option, use that
instead.
Signed-off-by: Rob Clark <robdclark@gmail.com>
The include file has been removed and the file does not
need it anyway, so remove it. Fixes a compile error.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The variable priv->kms is not initialized yet.
Found by "scripts/coccinelle/tests/odd_ptr_err.cocci".
PTR_ERR should access the value just tested by IS_ERR.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Occasionally we seem to miss an IRQ from the ME (microengine). I'm not
entirely sure the root cause, but for now we can unwedge things by
retiring from the hangcheck timer.
Signed-off-by: Rob Clark <robdclark@gmail.com>
When we CPU_PREP a bo with NOSYNC flag (for example, to implement
PIPE_TRANSFER_DISCARD_WHOLE_RESOURCE), an -EBUSY return indicates to
userspace that the bo is still busy. Previously it was incorrectly
returning 0 in this case.
And while we're in there throw in an bit of extra sanity checking in
case userspace tries to wait for a bogus fence.
Signed-off-by: Rob Clark <robdclark@gmail.com>
In case of error, the function drm_prime_pages_to_sg() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Need to check size+offset against bo size (duh!).. now we have a test
case to make sure I've done it right:
https://github.com/freedreno/msmtest/blob/master/submittest.c
Also, use DRM_ERROR() for error case traces, which makes debugging
userspace easier when enabling debug traces is too much.
Signed-off-by: Rob Clark <robdclark@gmail.com>
If gpu locks up with the rptr shortly beyond the wrap-around point in
the ringbuffer, because the rptr was not reset (but wptr is, by virtue
of resetting rb->cur), we could end up in a scenario where we think
there is not enough space in the ringbuffer for the next cmds. And
since the CP won't reset rptr until after processing an IB, this leaves
things in a sort of deadlock.
So reset rptr too. And a bit more spiffing up of hangcheck to make
things easier to debug.
Signed-off-by: Rob Clark <robdclark@gmail.com>
The userspace API already had everything needed to handle read vs write
synchronization. This patch actually bothers to hook it up properly, so
that we don't need to (for example) stall on userspace read access to a
buffer that gpu is also still reading.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Drop the msm_connector base class, and special calls to base class
methods from the encoder, and use instead drm_bridge. This allows for a
cleaner division between the hdmi (and in future dsi) blocks, from the
mdp block.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This lets drivers see the flags requested by the application
[airlied: fixup for rcar/imx/msm]
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
A basic, no-frills recovery mechanism in case the gpu gets wedged. We
could try to be a bit more fancy and restart the next submit after the
one that got wedged, but for now keep it simple. This is enough to
recover things if, for example, the gpu hangs mid way through a piglit
run.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add initial support for a3xx 3d core.
So far, with hardware that I've seen to date, we can have:
+ zero, one, or two z180 2d cores
+ a3xx or a2xx 3d core, which share a common CP (the firmware
for the CP seems to implement some different PM4 packet types
but the basics of cmdstream submission are the same)
Which means that the eventual complete "class" hierarchy, once
support for all past and present hw is in place, becomes:
+ msm_gpu
+ adreno_gpu
+ a3xx_gpu
+ a2xx_gpu
+ z180_gpu
This commit splits out the parts that will eventually be common
between a2xx/a3xx into adreno_gpu, and the parts that are even
common to z180 into msm_gpu.
Note that there is no cmdstream validation required. All memory access
from the GPU is via IOMMU/MMU. So as long as you don't map silly things
to the GPU, there isn't much damage that the GPU can do.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Generated from rnndb files in:
https://github.com/freedreno/envytools
Keep this split out as a separate commit to make it easier to review the
actual driver.
Signed-off-by: Rob Clark <robdclark@gmail.com>
The snapdragon chips have multiple different display controllers,
depending on which chip variant/version. (As far as I can tell, current
devices have either MDP3 or MDP4, and upcoming devices have MDSS.) And
then external to the display controller are HDMI, DSI, etc. blocks which
may be shared across devices which have different display controller
blocks.
To more easily add support for different display controller blocks, the
display controller specific bits are split out into a "kms" module,
which provides the kms plane/crtc/encoder objects.
The external HDMI, DSI, etc. blocks are part encoder, and part connector
currently. But I think I will pull in the drm_bridge patches from
chromeos tree, and split them into a bridge+connector, with the
registers that need to be set in modeset handled by the bridge. This
would remove the 'msm_connector' base class. But some things need to be
double checked to make sure I could get the correct ON/OFF sequencing..
This patch adds support for mdp4 crtc (including hw cursor), dtv encoder
(part of MDP4 block), and hdmi.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Generated from rnndb files in:
https://github.com/freedreno/envytools
Keep this split out as a separate commit to make it easier to review the
actual driver.
Signed-off-by: Rob Clark <robdclark@gmail.com>