The driver recently switched from handling page flip completion in the
DU vertical blanking handler to the VSP frame end handler to fix a race
condition. This unfortunately resulted in incorrect timestamps in the
vertical blanking events sent to userspace as vertical blanking is now
handled after sending the event.
To fix this we must reverse the order of the two operations. The easiest
way is to handle vertical blanking in the VSP frame end handler before
sending the event. The VSP frame end interrupt occurs approximately 50µs
earlier than the DU frame end interrupt, but this should not cause any
undue harm.
As we need to handle vertical blanking even when page flip completion is
delayed, the VSP driver now needs to call the frame end completion
callback unconditionally, with a new argument to report whether page
flip has completed.
With this new scheme the DU vertical blanking interrupt isn't needed
anymore, so we can stop enabling it.
Fixes: d503a43ac0 ("drm: rcar-du: Register a completion callback with VSP1")
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When stopping the CRTC the driver must disable all planes and wait for
the change to take effect at the next vblank. Merely calling
drm_crtc_wait_one_vblank() is not enough, as the function doesn't
include any mechanism to handle the race with vblank interrupts.
Replace the drm_crtc_wait_one_vblank() call with a manual mechanism that
handles the vblank interrupt race.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Commit 52055bafa1 ("drm: rcar-du: Move plane commit code from CRTC
start to CRTC resume") changed the order of the plane commit and CRTC
enable operations to accommodate the runtime PM requirements. However,
this introduced corruption in the first displayed frame, as the CRTC is
now enabled without any plane configured. On Gen2 hardware the first
frame will be black and likely unnoticed, but on Gen3 hardware we end up
starting the display before the VSP compositor, which is more
noticeable.
To fix this, revert the order of the commit operations back, and handle
runtime PM requirements in the CRTC .atomic_begin() and .atomic_enable()
helper operation handlers.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
On R-Car H3 ES2.0, DU channels 0 and 3 are served by two separate
pipelines from the same VSP. Support this in the DU driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Currently we process page flip events on every display interrupt,
however this does not take into consideration the processing time needed
by the VSP1 utilised in the pipeline.
Register a callback with the VSP driver to obtain completion events, and
track them so that we only perform page flips when the full display
pipeline has completed for the frame.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Update the device description with the two available HDMI outputs.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The vblank hooks in struct drm_driver are deprecated and only meant for
legacy drivers. For modern drivers with DRIVER_MODESET flag, the hooks
in struct drm_crtc_funcs should be used instead.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1486458995-31018-17-git-send-email-shawnguo@kernel.org
On R-Car Gen3 SoCs the DU lost its ability to access memory directly and
needs to work in conjunction with the VSP to do so. This commit handles
the VSP internally to hide it from the user.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The atomic framework guarantees that the CRTC enable and disable
functions will only be called when needed, there's no need to duplicate
the CRTC state check. By replacing the local CRTC enabled state check at
resume time with the CRTC active state we can remove the local CRTC
enabled state altogether.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Again since the drm core takes care of event unlinking/disarming this
is now just needless code.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453756616-28942-10-git-send-email-daniel.vetter@ffwll.ch
The rcar_du_crtc plane field is only used to check for an error that
can't occur. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Allow setting up plane properties atomically using the plane
set_property atomic helper. The properties are now stored in the plane
state (requiring subclassing it) and applied when updating the planes.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
When using atomic updates the CRTC .enable() and .disable() helper
operations are preferred over the (then legacy) .prepare() and .commit()
operations. Implement .enable() and rework .disable() to not depend on
DPMS, easing DPMS removal later on.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Turning a CRTC off will prevent a queued page flip from ever completing,
potentially confusing userspace. Wait for queued page flips to complete
before turning the CRTC off to avoid this.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The DU uses the module functional clock as the default pixel clock, but
supports using an externally supplied pixel clock instead. Support this
by adding the external pixel clock to the DT bindings, and selecting the
clock automatically at runtime based on the requested mode pixel
frequency.
The input clock pins to DU channels routing is configurable, but
currently hardcoded to connect input clock i to channel i.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
All platforms now instantiate the DU through DT, platform data support
isn't needed anymore.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The "Renesas Corporation" listed in the copyright notice doesn't exist.
Replace it with "Renesas Electronics Corporation" and update the
copyright years.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The R8A7790 includes two internal LVDS encoders. Support them in the DU
driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Split the output routing specification between SoC-internal data,
specified in the rcar_du_device_info structure, and board data, passed
through platform data.
The DU has 5 possible outputs (DPAD0/1, LVDS0/1, TCON). SoC-internal
output routing data specify which output are valid, which CRTCs can be
connected to the valid outputs, and the type of in-SoC encoder for the
output.
Platform data then specifies external encoders and the output they are
connected to.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The R8A7779 DU is split in per-CRTC resources (scan-out engine, blending
unit, timings generator, ...) and device-global resources (start/stop
control, planes, ...) shared between the two CRTCs.
The R8A7790 introduced a third CRTC with its own set of global resources
This would be modeled as two separate DU device instances if it wasn't
for a handful or resources that are shared between the three CRTCs
(mostly related to input and output routing). For this reason the
R8A7790 DU must be modeled as a single device with three CRTCs, two sets
of "semi-global" resources, and a few device-global resources.
Introduce a new rcar_du_group driver-specific object, without any real
counterpart in the DU documentation, that models those semi-global
resources.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Some of the DU revisions use one clock and IRQ per CRTC instead of one
clock and IRQ per device. Retrieve the correct clock and register the
correct IRQ for each CRTC.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The R-Car Display Unit (DU) DRM driver supports both superposition
processors and all eight planes in RGB and YUV formats with alpha
blending.
Only VGA and LVDS encoders and connectors are currently supported.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Kieran Bingham