The handling of hardware error has support for providing a vendor
specific callback to deal with the error. Move the Intel specific
function out of the USB driver into the generic module so that it
can also be utilized by the UART driver.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Removed semicolon at end of switch statement,error reported by Coccinelle
Signed-off-by: Prasanna Karthik <mkarthi3@visteon.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Removed semicolon at the end of switch case statement
Signed-off-by: Prasanna Karthik <mkarthi3@visteon.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Intel Lightning Peak devices do not come with Bluetooth firmware
loaded and thus require a full download of the operational Bluetooth
firmware when the device is attached via the Bluetooth line discipline.
Lightning Peak devices start with a bootloader mode that only accepts
a very limited set of HCI commands. The supported commands are enough
to identify the hardware and select the right firmware to load.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduces suspend and resume callbacks to mac802154. When
doing suspend we calling the stop driver callback which should stop the
receiving of frames. A transceiver should go into low-power mode then.
Calling resume will call the start driver callback, which starts receiving
again and allow to transmit frames.
This was tested only with the fakelb driver and a qemu vm by doing the
following commands:
echo "devices" > /sys/power/pm_test
echo "freeze" > /sys/power/state
while doing some high traffic between two fakelb phys.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch help to implement suspend/resume in mac802154, these
hooks will be run before the device is suspended and after it
resumes.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds ieee802154_stop_device for preparing a utility function
to stop the ieee802154 device.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the unused macro which was removed
with the rework of linux-wpan kernel.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch will generate the warning if the required driver ops
were not defined. Also it removes unnecessary debug message.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The iphc module depends on CONFIG_IPV6, because it's not very useful to
build the module without IPv6 support. Recently an user reported about
issues for setting an IPv6 address to a 6LoWPAN interface. The issues
was solved by modprobe the ipv6 module before. To avoid such user issues
we try to request the ipv6 module when the 6LoWPAN module is loaded.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a workaround for using the new nl802154 netlink
interface with the old ieee802154 netlink interface togehter. The
nl802154 currently supports no access for llsec layer, currently there
are users outside which are using both interfaces at the same time. This
patch adds a necessary call when addresses are updated.
Reported-by: Simon Vincent <simon.vincent@xsilon.com>
Suggested-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Braces {} are not necessary for single statement blocks reported by
checkpatch
Signed-off-by: Prasanna Karthik <mkarthi3@visteon.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Convert the module_init() to a invocation from inet_init() since
ip_tunnel_core is part of the INET built-in.
Fixes: 3093fbe7ff ("route: Per route IP tunnel metadata via lightweight tunnel")
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/bridge/br_mdb.c
br_mdb.c conflict was a function call being removed to fix a bug in
'net' but whose signature was changed in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Don't use shared bluetooth antenna in iwlwifi driver for management
frames, from Emmanuel Grumbach.
2) Fix device ID check in ath9k driver, from Felix Fietkau.
3) Off by one in xen-netback BUG checks, from Dan Carpenter.
4) Fix IFLA_VF_PORT netlink attribute validation, from Daniel Borkmann.
5) Fix races in setting peeked bit flag in SKBs during datagram
receive. If it's shared we have to clone it otherwise the value can
easily be corrupted. Fix from Herbert Xu.
6) Revert fec clock handling change, causes regressions. From Fabio
Estevam.
7) Fix use after free in fq_codel and sfq packet schedulers, from WANG
Cong.
8) ipvlan bug fixes (memory leaks, missing rcu_dereference_bh, etc.)
from WANG Cong and Konstantin Khlebnikov.
9) Memory leak in act_bpf packet action, from Alexei Starovoitov.
10) ARM bpf JIT bug fixes from Nicolas Schichan.
11) Fix backwards compat of ANY_LAYOUT in virtio_net driver, from
Michael S Tsirkin.
12) Destruction of bond with different ARP header types not handled
correctly, fix from Nikolay Aleksandrov.
13) Revert GRO receive support in ipv6 SIT tunnel driver, causes
regressions because the GRO packets created cannot be processed
properly on the GSO side if we forward the frame. From Herbert Xu.
14) TCCR update race and other fixes to ravb driver from Sergei
Shtylyov.
15) Fix SKB leaks in caif_queue_rcv_skb(), from Eric Dumazet.
16) Fix panics on packet scheduler filter replace, from Daniel Borkmann.
17) Make sure AF_PACKET sees properly IP headers in defragmented frames
(via PACKET_FANOUT_FLAG_DEFRAG option), from Edward Hyunkoo Jee.
18) AF_NETLINK cannot hold mutex in RCU callback, fix from Florian
Westphal.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (84 commits)
ravb: fix ring memory allocation
net: phy: dp83867: Fix warning check for setting the internal delay
openvswitch: allocate nr_node_ids flow_stats instead of num_possible_nodes
netlink: don't hold mutex in rcu callback when releasing mmapd ring
ARM: net: fix vlan access instructions in ARM JIT.
ARM: net: handle negative offsets in BPF JIT.
ARM: net: fix condition for load_order > 0 when translating load instructions.
tcp: suppress a division by zero warning
drivers: net: cpsw: remove tx event processing in rx napi poll
inet: frags: fix defragmented packet's IP header for af_packet
net: mvneta: fix refilling for Rx DMA buffers
stmmac: fix setting of driver data in stmmac_dvr_probe
sched: cls_flow: fix panic on filter replace
sched: cls_flower: fix panic on filter replace
sched: cls_bpf: fix panic on filter replace
net/mdio: fix mdio_bus_match for c45 PHY
net: ratelimit warnings about dst entry refcount underflow or overflow
caif: fix leaks and race in caif_queue_rcv_skb()
qmi_wwan: add the second QMI/network interface for Sierra Wireless MC7305/MC7355
ravb: fix race updating TCCR
...
Account for the configuration FIB_RULES=y && INET=n as FIB_RULES can
be selected by IPV6 or DECNET without INET.
Fixes: e7030878fc ("fib: Add fib rule match on tunnel id")
Fixes: 3093fbe7ff ("route: Per route IP tunnel metadata via lightweight tunnel")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per RFC 6724, section 4, "Candidate Source Addresses":
It is RECOMMENDED that the candidate source addresses be the set
of unicast addresses assigned to the interface that will be used
to send to the destination (the "outgoing" interface).
Add a sysctl to enable this behaviour.
Signed-off-by: Erik Kline <ek@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix for:
net/mpls/mpls_iptunnel.c:73:19: sparse: incompatible types in comparison
expression (different address spaces)
remove incorrect rcu_dereference possibly left over from
earlier revisions of the code.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz says:
====================
bnx2x: update FW, rebrand and more
This patch series does several things - it updates the bnx2x FW into
7.12.30 which both contains some small fixes as well as opening the door
for several new features for the device - mainly vxlan/geneve offloads
and vlan filtering offload.
It then adds a new Multi-function mode [BD] which requires this FW in
order to operate.
In addition, this finally rebrands the driver from a 'broadcom' driver
into a 'qlogic' driver [although it would still reside under Broadcom's
tree in the kernel].
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devices with up-to-date management FW will be able to store register dumps
on their persistent storage - in case management FW identifies a fatal
error it would gather and store such dumps, which could later be retrieved
using specific debug tools.
This patch adds the necessary part in the driver in order to make the
feature operational, as well as update users [under debug] during load
in case their device contains a dump of a previous crash.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support to a new multi-function mode, enabling driver to
initialize such devices and correctly interacting with management FW
for fully utilizing their features.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support to a new copper phy.
Signed-off-by: Yaniv Rosner <Yaniv.Rosner@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x still appears as a Broadcom driver even though the devices it
utilizes belong to Qlogic for more than a year.
This patch changes the various headers and the device strings to indicate
the correct ownership of the device.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This moves bnx2x into using 7.12.30 FW. Said firmware fixes the following:
- Packets from a VF with pvid configured which were sent with a
different vlan were transmitted instead of being discarded.
- FCoE traffic might not recover after a failue while there's traffic
to another function.
In addition, this FW opens the door for the driver to implement several
new features; Specifically, this enhances the device's support for
encapsulated packets and will allow vxlan/geneve offloads to be added in
the future, as well as vlan filtering offload.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
task_struct and the asm offsets becoming too large for the AArch64 ISA
- preparatory patch for moving irq_data struct members (applied now to
reduce dependency for the next merging window)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=GPY8
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull ARM64 fixes from Catalin Marinas:
- arm64 build fix following the move of the thread_struct to the end of
task_struct and the asm offsets becoming too large for the AArch64
ISA
- preparatory patch for moving irq_data struct members (applied now to
reduce dependency for the next merging window)
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
ARM64/irq: Use access helper irq_data_get_affinity_mask()
arm64: switch_to: calculate cpu context pointer using separate register
This is a preparatory patch for moving irq_data struct members.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Commit 0c8c0f03e3 ("x86/fpu, sched: Dynamically allocate 'struct fpu'")
moved the thread_struct to the bottom of task_struct. As a result, the
offset is now too large to be used in an immediate add on arm64 with
some kernel configs:
arch/arm64/kernel/entry.S: Assembler messages:
arch/arm64/kernel/entry.S:588: Error: immediate out of range
arch/arm64/kernel/entry.S:597: Error: immediate out of range
This patch calculates the offset using an additional register instead of
an immediate offset.
Fixes: 0c8c0f03e3 ("x86/fpu, sched: Dynamically allocate 'struct fpu'")
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The driver is written as if it can adapt to a low memory situation allocating
less RX skbs and TX aligned buffers than the respective RX/TX ring sizes. In
reality though the driver would malfunction in this case. Stop being overly
smart and just fail in such situation -- this is achieved by moving the memory
allocation from ravb_ring_format() to ravb_ring_init().
We leave dma_map_single() calls in place but make their failure non-fatal
by marking the corresponding RX descriptors with zero data size which should
prevent DMA to an invalid addresses.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add debugfs entry 'use_backdoor' to enable backdoor access to read sge
context. By default, we read sge context's via firmware. In case of FW
issues, one can enable backdoor access via debugfs to dump sge context
for debugging purpose.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix warning: logical ‘or’ of collectively exhaustive tests is always true
Change the internal delay check from an 'or' condition to an 'and'
condition.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If user did not specify an oif, try and get it from the via address.
If failed to get device, return with -ENODEV.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some architectures like POWER can have a NUMA node_possible_map that
contains sparse entries. This causes memory corruption with openvswitch
since it allocates flow_cache with a multiple of num_possible_nodes() and
assumes the node variable returned by for_each_node will index into
flow->stats[node].
Use nr_node_ids to allocate a maximal sparse array instead of
num_possible_nodes().
The crash was noticed after 3af229f2 was applied as it changed the
node_possible_map to match node_online_map on boot.
Fixes: 3af229f207
Signed-off-by: Chris J Arges <chris.j.arges@canonical.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Edward Cree says:
====================
sfc: support for cascaded multicast filtering
Recent versions of firmware for SFC9100 adapters add support for filter
chaining, in which packets matching multiple filters are delivered to all
filters' recipients, rather than only the highest match-priority filter as was
previously the case.
This patch series enables this feature and redesigns the filter handling code
to make use of it; in particular, subscribing to a multicast address on one
function no longer prevents traffic to that address reaching another function
which is in promiscuous or allmulti mode.
If the firmware does not support filter chaining, the driver will fall back to
the old behaviour.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate functions for inserting individual and promisc filters; explicit
fallback logic in efx_ef10_filter_sync_rx_mode(), in order not to overload
the 'promisc' flag as also meaning "fall back to promisc".
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the workaround to support cascaded multicast filters ("workaround_26807") is
enabled, the broadcast filter and individual multicast filters are not inserted
when in promiscuous or allmulti mode.
There is a race while inserting and removing filters when entering and leaving
promiscuous mode. When changing promiscuous state with cascaded multicast
filters, the old multicast filters are removed before inserting the new filters
to avoid duplicating packets; this can lead to dropped packets until all
filters have been inserted.
The efx_nic:mc_promisc flag is added to record the presence of a multicast
promiscuous filter; this gives a simple way to tell if the promiscuous state is
changing.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change is only re-factoring; there are no changes to functionality
except for a slight elaboration of an error message (on mismatch filter
insertion failure).
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a function is in promiscuous mode and another function has a broadcast or
multicast filter inserted, the function in promiscuous mode won't see that
broadcast or multicast traffic.
Most notably this breaks broadcast, which means ARP doesn't work. Less
show-stoppingly, a function listening on a multicast address that's also in
promiscuous mode will not see that multicast traffic if another function is
also listening on that multicast address.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enabling the workaround for cascaded multicast filters, the MC
can reset other functions if they have already inserted filters.
In that case, the workaround has been enabled, but print an info
message in the log recording that other functions had to be reset.
As other functions were reset, the MC will have incremented its boot
count, so also increment the warm_boot_count on the function which
enabled the workaround, as that function won't have received an MC
reboot event and does not need to reset.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The initial use of this will be to check a flag reporting if an FLR was
performed on other functions when enabling cascaded multicast filters.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GET_WORKAROUNDS was only introduced in May 2014, not all firmware
will have it. So call sites need to handle ENOSYS.
In this case we're probing the bug26807 workaround, which is not
implemented in any firmware that doesn't have GET_WORKAROUNDS.
So interpret ENOSYS as 'false'.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After creating event queue 0, check to see if the workaround is enabled,
and enable it if necessary. This will be called during PCI probe and
also when coming back up after a reset. The nic_data->workaround_26807
will be used in the future to control the filter insertion behaviour
based on this workaround.
Only the primary PF can enable this workaround, so tolerate an EPERM
error and continue. Otherwise, if any step in the checking and enabling
of the workaround fails, the event queue must be removed.
We check that workaround is implemented before trying to enable it,
and store the current workaround setting before trying to change it.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Schichan says:
====================
BPF JIT fixes for ARM
These patches are fixing bugs in the ARM JIT and should probably find
their way to a stable kernel. All 60 test_bpf tests in Linux 4.1 release
are now passing OK (was 54 out of 60 before).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes BPF_ANC | SKF_AD_VLAN_TAG and BPF_ANC | SKF_AD_VLAN_TAG_PRESENT
have the same behaviour as the in kernel VM and makes the test_bpf LD_VLAN_TAG
and LD_VLAN_TAG_PRESENT tests pass.
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, the JIT would reject negative offsets known during code
generation and mishandle negative offsets provided at runtime.
Fix that by calling bpf_internal_load_pointer_neg_helper()
appropriately in the jit_get_skb_{b,h,w} slow path helpers and by forcing
the execution flow to the slow path helpers when the offset is
negative.
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
To check whether the load should take the fast path or not, the code
would check that (r_skb_hlen - load_order) is greater than the offset
of the access using an "Unsigned higher or same" condition. For
halfword accesses and an skb length of 1 at offset 0, that test is
valid, as we end up comparing 0xffffffff(-1) and 0, so the fast path
is taken and the filter allows the load to wrongly succeed. A similar
issue exists for word loads at offset 0 and an skb length of less than
4.
Fix that by using the condition "Signed greater than or equal"
condition for the fast path code for load orders greater than 0.
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marcel Holtmann