These macros are used by more than one SoC vendor platforms, avoid to
have many copies of these code, this patch moves them to the common
header file which every clock drivers can access to.
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Sigma-delta modulation is supported for some PLLs. This allows
fractional-N multipliers to be used. In reality we don't know
how to configure the individual settings for it. However we can
copy existing settings from the vendor kernel to support clock
rates that cannot be generated from integer factors, but are
really desired. The vendor kernel only uses this for the audio
PLL clock, and only on the latest chips.
This patch adds a new class of clocks, along with helper functions.
It is intended to be merged into N-M-factor style clocks as a
feature, much like fractional clocks.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Starting with the A83T SoC, Allwinner introduced a new timing mode for
its MMC clocks. The new mode changes how the MMC controller sample and
output clocks are delayed to match chip and board specifics. There are
two controls for this, one on the CCU side controlling how the clocks
behave, and one in the MMC controller controlling what inputs to take
and how to route them.
In the old mode, the MMC clock had 2 child clocks providing the output
and sample clocks, which could be delayed by a number of clock cycles
measured from the MMC clock's parent.
With the new mode, the 2 delay clocks are no longer active. Instead,
the delays and associated controls are moved into the MMC controller.
The output of the MMC clock is also halved.
The difference in how things are wired between the modes means that the
clock controls and the MMC controls must match. To achieve this in a
clear, explicit way, we introduce two functions for the MMC driver to
use: one queries the hardware for the current mode set, and the other
allows the MMC driver to request a mode.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In common PLL designs, changes to the dividers take effect almost
immediately, while changes to the multipliers (implemented as
dividers in the feedback loop) take a few cycles to work into
the feedback loop for the PLL to stablize.
Sometimes when the PLL clock rate is changed, the decrease in the
divider is too much for the decrease in the multiplier to catch up.
The PLL clock rate will spike, and in some cases, might lock up
completely. This is especially the case if the divider changed is
the pre-divider, which affects the reference frequency.
This patch introduces a clk notifier callback that will gate and
then ungate a clk after a rate change, effectively resetting it,
so it continues to work, despite any possible lockups. Care must
be taken to reparent any consumers to other temporary clocks during
the rate change, and that this notifier callback must be the first
to be registered.
This is intended to fix occasional lockups with cpufreq on newer
Allwinner SoCs, such as the A33 and the H3. Previously it was
thought that reparenting the cpu clock away from the PLL while
it stabilized was enough, as this worked quite well on the A31.
On the A33, hangs have been observed after cpufreq was recently
introduced. With the H3, a more thorough test [1] showed that
reparenting alone isn't enough. The system still locks up unless
the dividers are limited to 1.
A hunch was if the PLL was stuck in some unknown state, perhaps
gating then ungating it would bring it back to normal. Tests
done by Icenowy Zheng using Ondrej's test firmware shows this
to be a valid solution.
[1] http://www.spinics.net/lists/arm-kernel/msg552501.html
Reported-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Icenowy Zheng <icenowy@aosc.io>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the Allwinner A80 SoC, the PLL lock status indicators are grouped
together in a separate register, as opposed to being scattered in each
PLL's configuration register.
Add a flag to support this.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some clocks have a global pre-divider that applies to all their parents.
Since it might also apply to clocks that have a single parent, this is
merged in the ccu_common structure, unlike the other pre-divider settings
that are tied to a specific index, and thus a specific parent.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Start our new clock infrastructure by adding the registration code, common
structure and common code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20160629190535.11855-3-maxime.ripard@free-electrons.com
Chunyan Zhang