Cache number of fragments in the skb locally as in case
of linear skb (with zero fragments), tx completion
(or freeing of skb) may happen before driver tries
to get number of frgaments from the skb which could
lead to stale access to an already freed skb.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VFs may hit VF-PF channel timeout while probing, as in some
cases it was observed that VF FLR and VF "acquire" message
transaction (i.e first message from VF to PF in VF's probe flow)
could occur simultaneously which could lead VF to fail sending
"acquire" message to PF as VF is marked disabled from HW perspective
due to FLR, which will result into channel timeout and VF probe failure.
In such cases, try retrying VF "acquire" message so that in later
attempts it could be successful to pass message to PF after the VF
FLR is completed and can be probed successfully.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VF is always configured to drop control frames
(with reserved mac addresses) but to work LACP
on the VFs, it would require LACP control frames
to be forwarded or transmitted successfully.
This patch fixes this in such a way that trusted VFs
(marked through ndo_set_vf_trust) would be allowed to
pass the control frames such as LACP pdus.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running tx switched traffic between VNICs
created via a bridge(to which VFs are added),
adapter drops the unicast packets in tx flow due to
VNIC's ucast mac being unknown to it. But VF interfaces
being in promiscuous mode should have caused adapter
to accept all the unknown ucast packets. Later, it
was found that driver doesn't really configure tx
promiscuous mode settings to accept all unknown unicast macs.
This patch fixes tx promiscuous mode settings to accept all
unknown/unmatched unicast macs and works out the scenario.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon says:
====================
qed*: Error recovery process
Parity errors might happen in the device's memories due to momentary bit
flips which are caused by radiation.
Errors that are not correctable initiate a process kill event, which blocks
the device access towards the host and the network, and a recovery process
is started in the management FW and in the driver.
This series adds the support of this process in the qed core module and in
the qede driver (patches 2 & 3).
Patch 1 in the series revises the load sequence, to avoid PCI errors that
might be observed during a recovery process.
Changes in v2:
- Addressed issue found in https://patchwork.ozlabs.org/patch/1030545/
The change was done be removing the enum and passing a boolean to
the related functions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the error recovery process in the qede driver.
The process includes a partial/customized driver unload and load, which
allows it to look like a short suspend period to the kernel while
preserving the net devices' state.
Signed-off-by: Tomer Tayar <tomer.tayar@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the detection and handling of a parity error ("process kill
event"), including the update of the protocol drivers, and the prevention
of any HW access that will lead to device access towards the host while
recovery is in progress.
It also provides the means for the protocol drivers to trigger a recovery
process on their decision.
Signed-off-by: Tomer Tayar <tomer.tayar@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initiating final cleanup after an ungraceful driver unload can lead to bad
PCI accesses towards the host.
This patch revises the load sequence so final cleanup is sent while the
internal master enable is cleared, to prevent the host accesses, and clears
the internal error indications just before enabling the internal master
enable.
Signed-off-by: Tomer Tayar <tomer.tayar@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
is_broadcast_packet() expands to compare_ether_addr() which doesn't
exist since commit 7367d0b573 ("drivers/net: Convert uses of
compare_ether_addr to ether_addr_equal"). It turns out it's actually not
used.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in i596_interrupt() when skb
xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <albin_yang@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for your net tree:
1) The nftnl mutex is now per-netns, therefore use reference counter
for matches and targets to deal with concurrent updates from netns.
Moreover, place extensions in a pernet list. Patches from Florian Westphal.
2) Bail out with EINVAL in case of negative timeouts via setsockopt()
through ip_vs_set_timeout(), from ZhangXiaoxu.
3) Spurious EINVAL on ebtables 32bit binary with 64bit kernel, also
from Florian.
4) Reset TCP option header parser in case of fingerprint mismatch,
otherwise follow up overlapping fingerprint definitions including
TCP options do not work, from Fernando Fernandez Mancera.
5) Compilation warning in ipt_CLUSTER with CONFIG_PROC_FS unset.
From Anders Roxell.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: Misc updates
This patchset contains miscellaneous patches we gathered in our queue.
Some of them are dependencies of larger patchsets that I will submit
later this cycle.
Patches #1-#3 perform small non-functional changes in mlxsw.
Patch #4 adds more extended ack messages in mlxsw.
Patch #5 adds devlink parameters documentation for mlxsw. To be extended
with more parameters this cycle.
Patches #6-#7 perform small changes in forwarding selftests
infrastructure.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It is easier to distinguish "[ OK ]" from "[FAIL]" than "[PASS]".
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Suggested-by: David Ahern <dsahern@gmail.com>
Cc: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As for the others, check help message output to find out if devlink
supports "resource" object.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add initial documentation file for devlink params of mlxsw driver. Only
"fw_load_policy" is now supported.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add more extack messages that let the user know why VXLAN offload
failed.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Suggested-by: David Ahern <dsahern@gmail.com>
Cc: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the struct to the place where they belong, alongside with the rest
of the MR code.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to pass ruleset/group and chunk pointers on action_replace call
path, nobody uses them.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 2830bf6f05.
The underlying assumption that one sparse section belongs into a single
numa node doesn't hold really. Robert Shteynfeld has reported a boot
failure. The boot log was not captured but his memory layout is as
follows:
Early memory node ranges
node 1: [mem 0x0000000000001000-0x0000000000090fff]
node 1: [mem 0x0000000000100000-0x00000000dbdf8fff]
node 1: [mem 0x0000000100000000-0x0000001423ffffff]
node 0: [mem 0x0000001424000000-0x0000002023ffffff]
This means that node0 starts in the middle of a memory section which is
also in node1. memmap_init_zone tries to initialize padding of a
section even when it is outside of the given pfn range because there are
code paths (e.g. memory hotplug) which assume that the full worth of
memory section is always initialized.
In this particular case, though, such a range is already intialized and
most likely already managed by the page allocator. Scribbling over
those pages corrupts the internal state and likely blows up when any of
those pages gets used.
Reported-by: Robert Shteynfeld <robert.shteynfeld@gmail.com>
Fixes: 2830bf6f05 ("mm, memory_hotplug: initialize struct pages for the full memory section")
Cc: stable@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clearly, I missed this when trying out the previously
merged patches. Remove the spurious variable now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Only one caller; place it where needed and get rid of the EXPORT_SYMBOL.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When nf_ct_netns_get() fails, it should clean up itself,
its caller doesn't need to call nf_conntrack_fini_net().
nf_conntrack_init_net() is called after registering sysctl
and proc, so its cleanup function should be called before
unregistering sysctl and proc.
Fixes: ba3fbe6636 ("netfilter: nf_conntrack: provide modparam to always register conntrack hooks")
Fixes: b884fa4617 ("netfilter: conntrack: unify sysctl handling")
Reported-and-tested-by: syzbot+fcee88b2d87f0539dfe9@syzkaller.appspotmail.com
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
nft_counter_rest() has its first argument declared as
struct nft_counter_percpu_priv __percpu *priv
but this structure is not percpu (it only countains
a member 'counter' which is, correctly, a pointer to a
percpu struct nft_counter).
So, remove the '__percpu' from the argument's declaration.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Use the new indirect call wrappers in IPVS when calling the TCP or UDP
protocol specific functions.
This avoids an indirect calls in IPVS, and reduces the performance
impact of the Spectre mitigation.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The function pointer ip_vs_protocol->csum_check is only used in protocol
specific code, and never in the generic one.
Remove the function pointer from struct ip_vs_protocol and call the
checksum functions directly.
This reduces the performance impact of the Spectre mitigation, and
should give a small improvement even with RETPOLINES disabled.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When CONFIG_PROC_FS isn't set the variable cn isn't used.
net/ipv4/netfilter/ipt_CLUSTERIP.c: In function ‘clusterip_net_exit’:
net/ipv4/netfilter/ipt_CLUSTERIP.c:849:24: warning: unused variable ‘cn’ [-Wunused-variable]
struct clusterip_net *cn = clusterip_pernet(net);
^~
Rework so the variable 'cn' is declared inside "#ifdef CONFIG_PROC_FS".
Fixes: b12f7bad5a ("netfilter: ipt_CLUSTERIP: remove wrong WARN_ON_ONCE in netns exit routine")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When we check the tcp options of a packet and it doesn't match the current
fingerprint, the tcp packet option pointer must be restored to its initial
value in order to do the proper tcp options check for the next fingerprint.
Here we can see an example.
Assumming the following fingerprint base with two lines:
S10:64:1:60:M*,S,T,N,W6: Linux:3.0::Linux 3.0
S20:64:1:60:M*,S,T,N,W7: Linux:4.19:arch:Linux 4.1
Where TCP options are the last field in the OS signature, all of them overlap
except by the last one, ie. 'W6' versus 'W7'.
In case a packet for Linux 4.19 kicks in, the osf finds no matching because the
TCP options pointer is updated after checking for the TCP options in the first
line.
Therefore, reset pointer back to where it should be.
Fixes: 11eeef41d5 ("netfilter: passive OS fingerprint xtables match")
Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Unlike ip(6)tables ebtables only counts user-defined chains.
The effect is that a 32bit ebtables binary on a 64bit kernel can do
'ebtables -N FOO' only after adding at least one rule, else the request
fails with -EINVAL.
This is a similar fix as done in
3f1e53abff ("netfilter: ebtables: don't attempt to allocate 0-sized compat array").
Fixes: 7d7d7e0211 ("netfilter: compat: reject huge allocation requests")
Reported-by: Francesco Ruggeri <fruggeri@arista.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Duec to a typo, mv88e6390_serdes_irq_setup() calls itself, rather than
mv88e6390x_serdes_irq_setup(). It then blows the stack, and shortly
after the machine blows up.
Fixes: 2defda1f4b ("net: dsa: mv88e6xxx: Add support for SERDES on ports 2-8 for 6390X")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the MC route socket is closed, mroute_clean_tables() is called to
cleanup existing routes. Mistakenly notifiers call was put on the cleanup
of the unresolved MC route entries cache.
In a case where the MC socket closes before an unresolved route expires,
the notifier call leads to a crash, caused by the driver trying to
increment a non initialized refcount_t object [1] and then when handling
is done, to decrement it [2]. This was detected by a test recently added in
commit 6d4efada3b ("selftests: forwarding: Add multicast routing test").
Fix that by putting notifiers call on the resolved entries traversal,
instead of on the unresolved entries traversal.
[1]
[ 245.748967] refcount_t: increment on 0; use-after-free.
[ 245.754829] WARNING: CPU: 3 PID: 3223 at lib/refcount.c:153 refcount_inc_checked+0x2b/0x30
...
[ 245.802357] Hardware name: Mellanox Technologies Ltd. MSN2740/SA001237, BIOS 5.6.5 06/07/2016
[ 245.811873] RIP: 0010:refcount_inc_checked+0x2b/0x30
...
[ 245.907487] Call Trace:
[ 245.910231] mlxsw_sp_router_fib_event.cold.181+0x42/0x47 [mlxsw_spectrum]
[ 245.917913] notifier_call_chain+0x45/0x7
[ 245.922484] atomic_notifier_call_chain+0x15/0x20
[ 245.927729] call_fib_notifiers+0x15/0x30
[ 245.932205] mroute_clean_tables+0x372/0x3f
[ 245.936971] ip6mr_sk_done+0xb1/0xc0
[ 245.940960] ip6_mroute_setsockopt+0x1da/0x5f0
...
[2]
[ 246.128487] refcount_t: underflow; use-after-free.
[ 246.133859] WARNING: CPU: 0 PID: 7 at lib/refcount.c:187 refcount_sub_and_test_checked+0x4c/0x60
[ 246.183521] Hardware name: Mellanox Technologies Ltd. MSN2740/SA001237, BIOS 5.6.5 06/07/2016
...
[ 246.193062] Workqueue: mlxsw_core_ordered mlxsw_sp_router_fibmr_event_work [mlxsw_spectrum]
[ 246.202394] RIP: 0010:refcount_sub_and_test_checked+0x4c/0x60
...
[ 246.298889] Call Trace:
[ 246.301617] refcount_dec_and_test_checked+0x11/0x20
[ 246.307170] mlxsw_sp_router_fibmr_event_work.cold.196+0x47/0x78 [mlxsw_spectrum]
[ 246.315531] process_one_work+0x1fa/0x3f0
[ 246.320005] worker_thread+0x2f/0x3e0
[ 246.324083] kthread+0x118/0x130
[ 246.327683] ? wq_update_unbound_numa+0x1b0/0x1b0
[ 246.332926] ? kthread_park+0x80/0x80
[ 246.337013] ret_from_fork+0x1f/0x30
Fixes: 088aa3eec2 ("ip6mr: Support fib notifications")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Digging through the ioctls with Al because of the previous
patches, we found that on 64-bit decnet's dn_dev_ioctl()
is wrong, because struct ifreq::ifr_ifru is actually 24
bytes (not 16 as expected from struct sockaddr) due to the
ifru_map and ifru_settings members.
Clearly, decnet expects the ioctl to be called with a struct
like
struct ifreq_dn {
char ifr_name[IFNAMSIZ];
struct sockaddr_dn ifr_addr;
};
since it does
struct ifreq *ifr = ...;
struct sockaddr_dn *sdn = (struct sockaddr_dn *)&ifr->ifr_addr;
This means that DN_IFREQ_SIZE is too big for what it wants on
64-bit, as it is
sizeof(struct ifreq) - sizeof(struct sockaddr) +
sizeof(struct sockaddr_dn)
This assumes that sizeof(struct sockaddr) is the size of ifr_ifru
but that isn't true.
Fix this to use offsetof(struct ifreq, ifr_ifru).
This indeed doesn't really matter much - the result is that we
copy in/out 8 bytes more than we should on 64-bit platforms. In
case the "struct ifreq_dn" lands just on the end of a page though
it might lead to faults.
As far as I can tell, it has been like this forever, so it seems
very likely that nobody cares.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If phy_power_on() fails in rk_gmac_powerup(), clocks are left enabled.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Peng Li says:
====================
net: hns: code optimizations & bugfixes for HNS driver
This patchset includes bugfixes and code optimizations for the HNS
ethernet controller driver
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When reading phy registers via Clause 45 MDIO protocol, after write
address operation, the driver use another write address operation, so
can not read the right value of any phy registers. This patch fixes it.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hns driver of earlier devices, when autoneg off, restart autoneg
will return -EINVAL, so make the hns driver for the latest devices
do the same.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In hns enet driver, we use of_parse_handle() to get hold of the
device node related to "ae-handle" but we have missed to put
the node reference using of_node_put() after we are done using
the node. This patch fixes it.
Note:
This problem is stated in Link: https://lkml.org/lkml/2018/12/22/217
Fixes: 48189d6aaf ("net: hns: enet specifies a reference to dsaf")
Reported-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
The tools/testing/selftests/bpf/test_verifier.c file is
way too large, and since most people add their at the
end of the list it's very prone to conflicts.
Break it up in the simplest possible way - slice the
array up into smaller C files and include them in the
right spot.
Tested:
$ make -C tools/testing/selftests/bpf/
$ cd tools/testing/selftests/bpf/ ; make
v2:
The indentation is reduced further as discussed and lines folded.
The conversion was scripted, and double checked by hand.
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Break up the rest of test_verifier tests into separate
files.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Break up the first 10 kLoC of test verifier test cases
out into smaller files. Looks like git line counting
gets a little flismy above 16 bit integers, so we need
two commits to break up test_verifier.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
test_verifier.c has grown to be very long (almost 16 kLoC),
and it is very conflict prone since we always add tests at
the end.
Try to break it apart a little bit. Allow test snippets
to be defined in separate files and include them automatically
into the huge test array.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Wei Wang says:
====================
tcp: change pingpong to 3 in delayed ack logic
TCP receiver today tries not to delay the ACKs to speed up the initial
slow start (a.k.a QUICK ACK mechanism). However the previous design
does not work well with modern TCP applications that starts with an
application-level handshake. For example, a HTTPs server often
receives the SSL hello and responds right away which triggers the TCP
stack to stop the quick ack and start delaying the ACKs based only one
instance of ping-pong. This patchset changes the threshold from 1 to 3
ping-pong transactions, so that we only start to delay the acks after
the receiver responds data quickly three times.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to be more confident about an on-going interactive session, we
increment pingpong count by 1 for every interactive transaction and we
adjust TCP_PINGPONG_THRESH to 3.
This means, we only consider a session in pingpong mode after we see 3
interactive transactions, and start to activate delayed acks in quick
ack mode.
And in order to not over-count the credits, we only increase pingpong
count for the first packet sent in response for the previous received
packet.
This is mainly to prevent delaying the ack immediately after some
handshake protocol but no real interactive traffic pattern afterwards.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using pingpong as a single bit information, we refactor the
code to treat it as a counter. When interactive session is detected,
we set pingpong count to TCP_PINGPONG_THRESH. And when pingpong count
is >= TCP_PINGPONG_THRESH, we consider the session in pingpong mode.
This patch is a pure refactor and sets foundation for the next patch.
This patch itself does not change any pingpong logic.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix blank line coding style issues, make the code cleaner.
Remove a redundant blank line in ip_rcv_core().
Insert a blank line in ip_rcv() between different statement blocks.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Libphy provides a standard set of helpers to access the MMD PHY
registers. Use those instead of relying on custom driver-specific
functions.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull x86 fixes from Thomas Gleixner:
"A set of fixes for x86:
- Fix the swapped outb() parameters in the KASLR code
- Fix the PKEY handling at fork which missed to preserve the pkey
state for the child. Comes with a test case to validate that.
- Fix the entry stack handling for XEN PV to respect that XEN PV
systems enter the function already on the current thread stack and
not on the trampoline.
- Fix kexec load failure caused by using a stale value when the
kexec_buf structure is reused for subsequent allocations.
- Fix a bogus sizeof() in the memory encryption code
- Enforce PCI dependency for the Intel Low Power Subsystem
- Enforce PCI_LOCKLESS_CONFIG when PCI is enabled"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/Kconfig: Select PCI_LOCKLESS_CONFIG if PCI is enabled
x86/entry/64/compat: Fix stack switching for XEN PV
x86/kexec: Fix a kexec_file_load() failure
x86/mm/mem_encrypt: Fix erroneous sizeof()
x86/selftests/pkeys: Fork() to check for state being preserved
x86/pkeys: Properly copy pkey state at fork()
x86/kaslr: Fix incorrect i8254 outb() parameters
x86/intel/lpss: Make PCI dependency explicit
Pull x86 timer fixes from Thomas Gleixner:
"Two commits which were missed to be sent during the merge window.
- The TSC calibration fix turns out to be more urgent as recent
Skylake-X systems seem to have massive trouble with calibration
disturbance. This should go back into stable for that reason and it
the risk of breakage is rather low.
- Drop an unused define"
* 'x86-timers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/hpet: Remove unused FSEC_PER_NSEC define
x86/tsc: Make calibration refinement more robust
Pull timer fix from Thomas Glexiner:
"A single regression fix to address the unintended breakage of posix
cpu timers.
This is caused by a new sanity check in the common code, which fails
for posix cpu timers under certain conditions because the posix cpu
timer code never updates the variable which is checked"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
posix-cpu-timers: Unbreak timer rearming
Manish Chopra