Introducing a module param for wakeup_delay in order to
align with modeswitch_delay parameter. With this change, both
wakeup_delay and modeswitch_delay parameters can be passed
as module parameters.
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On startup, applications such as PulseAudio or CRAS enable playback or
capture on all PCM devices to verify that configurations are correct,
and close them immediately. For DMICs, this can result in the clock
being turned off very quickly, which may not compatible with internal
state machine transition requirements.
This patch add a mode-switch delay which will prevent the clock from
being turned off without complying with manufacturer timing
specifications. While the DMIC clock may be controlled at a lower level,
be it with hardware or firmware, applying the delay during the
STOP_TRIGGER phase ensures that there is no race condition, e.g. with
the hardware/firmware turning off the clock earlier
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Signed-off-by: Jairaj Arava <jairaj.arava@intel.com>
Signed-off-by: Harsha Priya <harshapriya.n@intel.com>
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a callback for init ops on dai_link to create and setup jack.
Signed-off-by: Rohit kumar <rohitkr@codeaurora.org>
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add board specific dapm widgets so these widgets can be used
in the route.
Signed-off-by: Rohit kumar <rohitkr@codeaurora.org>
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the dismod is specified in the DT node, use the specified custom value
to configure the drive on state of the inactive TX slots.
If the dismod is not present or booted in legacy mode, the dismod is set
to low as it was the original behavior.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When McASP is master and the PDIR for the clock pins are configured as
outputs before the clocking is configured it will output whatever clock
is generated at the moment internally.
The clock will switch to the correct rate only when the we start the clock
generators.
To avoid this we must only set the pin as output after the clock is
configured and enabled.
AXR pins configured as outputs behaves somehow interesting as well:
when McASP is not enabled and the pin is selected as output it will not
honor the DISMOD settings for the inactive state, but will pull the pin
down.
Add a new bitfield and mark the pins there which needs to be output and
set the pins only at the time when they will behave correctly.
On stream stop configure the pins back to input which makes them to obey
the global pin configuration regarding to pull up/down.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Follow the guideline from the TRM:
Before starting, clear the respective transmitter and receiver status
registers
To avoid stale state stored in the status registers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If mclk/sclk is already running, FW responds with IPC reply MCLK/SCLK
already running. Add these to the IPC reply lookup table.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Sriram Periyasamy <sriramx.periyasamy@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add more meaning to the IPC replies for easy debugging. Replace the switch
case with a lookup table to lookup for the IPC replies and print in human
readable form.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Sriram Periyasamy <sriramx.periyasamy@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Like the Dell WD15 Dock, the WD19 Dock (0bda:402e) doens't provide
useful string for the vendor and product names too. In order to share
the UCM with WD15, here we keep the profile_name same as the WD15.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Current rsnd dvc.c is using flags to avoid duplicating register for
MIXer case. OTOH, commit e894efef9a ("ASoC: core: add support to card
rebind") allows to rebind sound card without rebinding all drivers.
Because of above patch and dvc.c flags, it can't re-register kctrl if
only sound card was rebinded, because dvc is keeping old flags.
(Of course it will be no problem if rsnd driver also be rebinded,
but it is not purpose of above patch).
This patch checks current card registered kctrl when registering.
In MIXer case, it can avoid duplicate register if card already has same
kctrl. In rebind case, it can re-register kctrl because card registered
kctl had been removed when unbinding.
This patch is updated version of commit b918f1bc7f ("ASoC: rsnd: DVC
kctrl sets once")
Reported-by: Nguyen Viet Dung <dung.nguyen.aj@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Nguyen Viet Dung <dung.nguyen.aj@renesas.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Lots of fixes here, the majority of which are driver specific but
there's a couple of core things and one notable driver specific one:
- A core fix for a DAPM regression introduced during the component
refactoring, we'd lost the code that forced a reevaluation of the
DAPM graph after probe (which we suppress during init to save lots
of recalcuation) and have now restored it.
- A core fix for error handling using the newly added
for_each_rtd_codec_dai_rollback() macro.
- A fix for the names of widgets in the newly introduced pcm3060
driver, merged as a fix so we don't have a release with legacy names.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlv9WBQTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0KeSB/9mrVVRe8hVg2ErfCEY8BaPGIdtNoBT
IIRh/woXwbZEsY3owRuF5FeQxUbsRWLQL8fnzLFE7b6ltlRiPKahIGG0rIE0Xqcz
jkvqR0Kvck1MLNjj8qyd72Eqv0uQmW5qoezY9eFJiWms5uIlbh+WR3KPFu4WkcnD
9DHoYYq4ZU3EIqgt92QJ2uOWPwrSfueBcz6+bdYy11mSMuUtHz4HaAV8/XGFEjFy
9uPeNmS4nTFxGXR5PzpxTP1mG7nYixq3J07iwXGTH/X3LDANmJCPgMgQQRnY6h1k
KrtnZfcNljJxyYuNPV/A3ShG98Snbym17cq2zN1o9ZBUlPyxfGdRwrTd
=NoTQ
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.20-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v4.20
Lots of fixes here, the majority of which are driver specific but
there's a couple of core things and one notable driver specific one:
- A core fix for a DAPM regression introduced during the component
refactoring, we'd lost the code that forced a reevaluation of the
DAPM graph after probe (which we suppress during init to save lots
of recalcuation) and have now restored it.
- A core fix for error handling using the newly added
for_each_rtd_codec_dai_rollback() macro.
- A fix for the names of widgets in the newly introduced pcm3060
driver, merged as a fix so we don't have a release with legacy names.
This patch will enable ALC300.
[ It's almost equivalent with other ALC269-compatible ones, and
apparently has no loopback mixer -- tiwai ]
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This device makes a loud buzzing sound when a headphone is inserted while
playing audio at full volume through the speaker.
Fixes: bbf8ff6b1d ("ALSA: hda/realtek - Fixup for HP x360 laptops with B&O speakers")
Signed-off-by: Girija Kumar Kasinadhuni <gkumar@neverware.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The platform_device_register_full() function doesn't return NULL, it
returns error pointers.
Fixes: 7894a7e7ea ("ASoC: amd: create ACP3x PCM platform device")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We have several Lenovo laptops with the codec alc285, when playing
sound via headphone, we can hear click/pop noise in the headphone,
if we let the headphone share the DAC of NID 0x2 with the speaker,
the noise disappears.
The Lenovo laptops here include P52, P72, X1 yoda2 and X1 carbon.
I have tried to set preferred_dacs and override_conn, but neither of
them worked. Thanks for Kailang, he told me to invalidate the NID 0x3
through override_wcaps.
BugLink: https://bugs.launchpad.net/bugs/1805079
Cc: <stable@vger.kernel.org>
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Both snd_ctl_add() and snd_ctl_replace() process the things in a
fairly similar way, and indeed the most of the codes can be unified.
This patch is a refactoring to consolidate the both functions to call
a single helper with an extra "mode" argument. There should be no
functional difference, except for one additional sanity check applied
now to snd_ctl_replace() (which was rather overlooking, IMO), too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The procedure for adding a user control element has some window opened
for race against the concurrent removal of a user element. This was
caught by syzkaller, hitting a KASAN use-after-free error.
This patch addresses the bug by wrapping the whole procedure to add a
user control element with the card->controls_rwsem, instead of only
around the increment of card->user_ctl_count.
This required a slight code refactoring, too. The function
snd_ctl_add() is split to two parts: a core function to add the
control element and a part calling it. The former is called from the
function for adding a user control element inside the controls_rwsem.
One change to be noted is that snd_ctl_notify() for adding a control
element gets called inside the controls_rwsem as well while it was
called outside the rwsem. But this should be OK, as snd_ctl_notify()
takes another (finer) rwlock instead of rwsem, and the call of
snd_ctl_notify() inside rwsem is already done in another code path.
Reported-by: syzbot+dc09047bce3820621ba2@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some spurious calls of snd_free_pages() have been overlooked and
remain in the error paths of sparc cs4231 driver code. Since
runtime->dma_area is managed by the PCM core helper, we shouldn't
release manually.
Drop the superfluous calls.
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some spurious calls of snd_free_pages() have been overlooked and
remain in the error paths of wss driver code. Since runtime->dma_area
is managed by the PCM core helper, we shouldn't release manually.
Drop the superfluous calls.
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
MSI Cubi N 8GL (MS-B171) needs the same fixup as its older model, the
MS-B120, in order for the headset mic to be properly detected.
They both use a single 3-way jack for both mic and headset with an
ALC283 codec, with the same pins used.
Cc: stable@vger.kernel.org
Signed-off-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Power-saving is causing plops on audio start/stop on the built-in audio
of the nForce 430 based ASRock N68C-S UCC motherboard, add this model to
the power_save blacklist.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1525104
Cc: <stable@vger.kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The function snd_ac97_put_spsa() gets the bit shift value from the
associated private_value, but it extracts too much; the current code
extracts 8 bit values in bits 8-15, but this is a combination of two
nibbles (bits 8-11 and bits 12-15) for left and right shifts.
Due to the incorrect bits extraction, the actual shift may go beyond
the 32bit value, as spotted recently by UBSAN check:
UBSAN: Undefined behaviour in sound/pci/ac97/ac97_codec.c:836:7
shift exponent 68 is too large for 32-bit type 'int'
This patch fixes the shift value extraction by masking the properly
with 0x0f instead of 0xff.
Reported-and-tested-by: Meelis Roos <mroos@linux.ee>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In former commits, ALSA firewire-tascam driver queues events to notify
change of state of control surface to userspace via ALSA hwdep
interface.
This commit implements actual notification of the events. The events are
not governed by real time, thus no need to care underrun.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In later commits, ALSA firewire-tascam driver will allow userspace
applications to receive notifications about changes of device state,
transferred in tx isochronous packet. At present, all of drivers in ALSA
firewire stack have mechanism to notify change of status of packet
streaming, thus it needs to distinguish these two types of notification.
This commit is a preparation for the above.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Units of TASCAM FireWire series transfer image of states of the unit in
tx isochronous packets. Demultiplexing of the states from the packets
is done in software interrupt context regardless of any process context.
In a view of userspace applications, it needs to have notification
mechanism to catch change of the states.
This commit implements a queue to store events for the notification. The
image of states includes fluctuating data such as level of gain/volume
for physical input/output and position of knobs. Therefore the events
are queued corresponding to some control features only.
Furthermore, the queued events are planned to be consumed by userspace
applications via ALSA hwdep interface. This commit suppresses event
queueing when no applications open the hwdep interface.
However, the queue is maintained in an optimistic scenario, thus without
any care against overrrun. This is reasonable because target events are
useless just to handle PCM frames. It starts queueing when an usespace
application opens hwdep interface, thus it's expected to read the queued
events steadily.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In a previous commit, ALSA firewire-tascam driver stores state image
from tx isochronous packets. This image includes states of knob, fader,
button of control surface, level of gain/volume of each physical
inputs/outputs, and so on. It's useful for userspace applications to
read whole of the image.
This commit adds a unique ioctl command for ALSA hwdep interface for the
purpose. For actual meaning of each bits in this image, please refer to
discussion in alsa-devel[1].
[1] http://mailman.alsa-project.org/pipermail/alsa-devel/2018-October/140785.html
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Units of TASCAM FireWire series multiplex PCM frames and state of
control surface into the same tx isochronous packets. One isochronous
packet includes a part of the state in a quadlet data. An image of the
state consists of 64 quadlet data.
This commit demultiplexes the state from tx isochronous packets.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We need to block sleep states which would require longer time to leave than
the time the DMA must react to the DMA request in order to keep the FIFO
serviced without overrun.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We need to block sleep states which would require longer time to leave than
the time the DMA must react to the DMA request in order to keep the FIFO
serviced without under of overrun.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The latency number is in usec for the pm_qos. Correct the calculation to
give us the time in usec
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit f986907c92 ("ASoC: audio-graph-card: add widgets and routing for
external amplifier support") added new function
asoc_graph_card_outdrv_event(), but the inserted position breaks
define area. This patch tidyup it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
1 "simple" is enough on Kconfig help
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current audio-graph-scu-card driver is parsing codec position for DPCM
and consider DAI format. But, current operation is doing totally pointless,
because 1) asoc_simple_card_parse_daifmt() will be called not only for 1st
codec on current implementation, and it will be used as fixed format
2) it should be called for each CPU/Codec pair.
Let's tidyup asoc_simple_card_parse_daifmt() timing.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
audio-graph-scu-card.c is supporting "convert-rate/channels" which is
used for DPCM.
But, sound card might have multi codecs, and each codec might need
each convert-rate/channels.
This patch supports each codec's convert-rate/channles support.
top node convert-rate/channels will overwrite settings if exist.
It can't support each codec's convert-rate/channels if sound card had
multi codecs without this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
audio-graph-scu-card.c is supporting "prefix" which is used to avoid
DAI naming conflict when CPU/Codec matching.
But, sound card might have multi sub-devices, and each codec might need
each prefix.
Now, ASoC is supporting snd_soc_of_parse_node_prefix(), let's support
it on audio-graph-scu-card, too. It is keeping existing DT style.
It can't support each codec's prefix if sound card had multi sub-devices
without this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
simple-scu-card.c is supporting "prefix" which is used to avoid
DAI naming conflict when CPU/Codec matching.
But, sound card might have multi sub-devices, and each codec might need
each prefix.
Now, ASoC is supporting snd_soc_of_parse_node_prefix(), let's support
it on audio-graph-scu-card, too. It is keeping existing DT style.
It can't support each codec's prefix if sound card had multi sub-devices
without this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ASoC has snd_soc_of_parse_audio_prefix() to get codec_conf
settings from DT which is used to avoid DAI naming conflict when
CPU/Codec matching.
Currently, it is parsing from "top node",
but, we want to parse from "each sub node" if sound card had multi
cpus/codecs.
This patch adds new snd_soc_of_parse_node_prefix() to allow parsing
settings from selected node.
It is keeping existing snd_soc_of_parse_audio_prefix() by using macro.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Amplifier may have assosicated regulator, so add a widget for it
and appropriate route.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On the Allwinner A64 SoCs, the audio codec has a built-in headphone
amplifier. This amplifier has a power supply separate from the rest of
the analog audio circuitry, labeled cpvdd.
This patch adds a DAPM widget for this supply, and ties it to the
headphone amp widget.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
asoc_simple_card_of_parse_routing() had "option" parameter
to consider error handling, but it is very pointless parameter.
Let's remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current simple-card-utils has asoc_simple_card_parse_convert() to parse
convert channel/rate for be_hw_params_fixup.
But, it is parsing from top of node.
If sound card had multi subnode, we need to parse it from each sub node.
This patch tidyup asoc_simple_card_parse_convert() to allow parsing
settings from each node.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If simple-card-utils accept NULL pointer on asoc_simple_card_xxx(),
each driver code will be more simple.
Let's accept NULL pointer.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
asoc_simple_card_clk_register() is used but only 1 user,
and very pointless code. Let's remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ssi.c only is using rsnd_ssi_is_dma_mode().
Let's move it as static function.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_parse_connect_ssiu_compatible() is doing
- using rsnd_ssiu_id(), but we use it via rsnd_mod_id()
- we can break loop if rsnd_dai_connect() was called
This patch fixup these.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support to configure bit clock for secondary MI2S
TX interface.
Signed-off-by: Rohit kumar <rohitkr@codeaurora.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Change slot_width for quaternary TDM port to 16 and
update bclk rate for TDM and MI2S interfaces
accordingly.
Signed-off-by: Rohit kumar <rohitkr@codeaurora.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
For some reason we have different mechanisms for passing data to
machine drivers. Use the solution used by Atom/SST and SOF instead of
using drv_data as done by Skylake.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The changes for HDaudio overlooked the fact that the machine drivers
used for Chromebooks rely on the dmic number information passed as
pdata.
Add dmic_num field to standard interface and use standard interface
instead of SKL-specific one.
Also clean-up pdata definition to remove fields that are no longer
used.
Fixes: 842bb5135f ('ASoC: Intel: use standard interface for Hdaudio machine driver')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The machine_quirk may return NULL which means the acpi entries should be
skipped and search for next matched entry is needed, here add return
check here and continue for NULL case.
Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Skylake driver currently has a set of problems supporting
load/unload modules. We need to make the HDaudio codec support
optional to help narrow down the issues.
Support for HDaudio codecs also leads to a Kconfig issue. We want the
hdac_hda codec to be compilable independently of Skylake (e.g. with
ALL_CODECS) but when Skylake is selected as built-in the hdac_hda
codec needs to use the same option due a a code dependency
Solve both problems by adding a user-selectable boolean Kconfig,
select HDAC_HDA as needed and make the HDaudio codec support in the
Skylake driver optional. Tests on a Chell Chromebook device without
HDaudio show no regression for speaker and HDMI playback.
This is submitted as an RFC to allow for comments and more validation.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec can support any variation of bclk/fs master/slave configuration.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove directly accessing device_node.type pointer and use the accessors
instead. This will eventually allow removing the type pointer.
Replace the open coded iterating over child nodes with
for_each_child_of_node() while we're here.
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: alsa-devel@alsa-project.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch fixes the pincfg assignment for the AE-5, which was
previously using the Recon3D pincfg's by mistake.
Fixes: d06feaf02f ("ALSA: hda/ca0132 - Add pincfg for AE-5")
Signed-off-by: Connor McAdams <conmanx360@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds a new PCI subsys ID for the ZxR, as found and tested by
other users. Without a way to know if any Z's use it as well, it keeps
the quirk of QUIRK_SBZ and goes through the HDA subsys test function.
Signed-off-by: Connor McAdams <conmanx360@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The struct declaration is not indented correctly. Fix this by replacing
spaces with a tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The default implementation of regulator_set_load returns
REGULATOR_MODE_NORMAL, which is positive. [This was a bug which is
being fixed but the change is valid anyway -- bronie]
rt5663_i2c_probe should only do error handling when return value of
regulator_set_load is negative.
In this case, rt5663_i2c_probe should return error.
Also, consolidate err_irq into err_enable.
Fix the missing goto for temporary regmap and rt5663->regmap.
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a spelling mistake in a dev_err message. Fix this.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The return statement is indented too much by one level, fix this by
removing the extraneous tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The return statement is indented incorrectly. Fix this by adding in
the missing tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The goto statement is indented too much by one level, fix this by
removing the extraneous tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The return statement is indented too much by one level, fix this by
removing an extraneous tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Olivier Moysan <olivier.moysan@st.com>
Cc: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: alsa-devel@alsa-project.org
Cc: linux-stm32@st-md-mailman.stormreply.com
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add regulator support to turn on cpvdd and avdd in probe.
If a regulator is not given from device tree, a dummy regulator will be
used.
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The AK4118A is a digital audio transceiver supporting 8 input channels
at 192kHz and with 24bits resolution.
It converts the S/PDIF signal to I2S format and is configurable over I2C.
This driver introduce a minimal support of the AK4118, like selecting the
input channel, reading input frequency and detecting some errors.
Datasheet is available here:
https://www.akm.com/akm/en/file/datasheet/AK4118AEQ.pdf
Signed-off-by: Adrien Charruel <adrien.charruel@devialet.com>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the current device datasheet (TI Lit # SLAS831D, revised
March 2018) the value written to the device's PAGE register to trigger
a complete register reset should be 0xfe, not 0xff. So go ahead and
update to the correct value.
Reported-by: Stephane Le Provost <stephane.leprovost@mediatek.com>
Tested-by: Stephane Le Provost <stephane.leprovost@mediatek.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Fixes gcc '-Wunused-but-set-variable' warning:
sound/soc/amd/raven/acp3x-pcm-dma.c: In function 'acp3x_dma_hw_params':
sound/soc/amd/raven/acp3x-pcm-dma.c:333:25: warning:
variable 'dma_buffer' set but not used [-Wunused-but-set-variable]
It never used since introduction in commit
8de1b5ed03 ("ASoC: amd: add acp3x system resume pm op")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license
compliance management.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Vijendar Mukunda <vijendar.mukunda@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixed build errors.
- Implicit declaration of pci_enable_msi() & pci_disable_msi()
api's for openrisc architecture.
- type defaults to 'int' in declaration of 'module_pci_driver'
Enabled build for x86 architecture.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Vijendar Mukunda <vijendar.mukunda@amd.com>
Tested-by: Ravulapati Vishnu vardhan Rao <Vishnuvardhanrao.Ravulapati@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch updates license to SPDX-License-Identifier
instead of verbose license text.
Signed-off-by: David Lin <CTLIN0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Audio map are possible in wrong state before card->instantiated has
been set to true. Imaging the following examples:
time 1: at the beginning
in:-1 in:-1 in:-1 in:-1
out:-1 out:-1 out:-1 out:-1
SIGGEN A B Spk
time 2: after someone called snd_soc_dapm_new_widgets()
(e.g. create_fill_widget_route_map() in sound/soc/codecs/hdac_hdmi.c)
in:1 in:0 in:0 in:0
out:0 out:0 out:0 out:1
SIGGEN A B Spk
time 3: routes added
in:1 in:0 in:0 in:0
out:0 out:0 out:0 out:1
SIGGEN -----> A -----> B ---> Spk
In the end, the path should be powered on but it did not. At time 3,
"in" of SIGGEN and "out" of Spk did not propagate to their neighbors
because snd_soc_dapm_add_path() will not invalidate the paths if
the card has not instantiated (i.e. card->instantiated is false).
To correct the state of audio map, recalculate the whole map forcely.
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The machine driver fails to probe in next-20181113 with:
[ 2.539093] omap-abe-twl6040 sound: ASoC: CODEC DAI twl6040-legacy not registered
[ 2.546630] omap-abe-twl6040 sound: devm_snd_soc_register_card() failed: -517
...
[ 3.693206] omap-abe-twl6040 sound: ASoC: Both platform name/of_node are set for TWL6040
[ 3.701446] omap-abe-twl6040 sound: ASoC: failed to init link TWL6040
[ 3.708007] omap-abe-twl6040 sound: devm_snd_soc_register_card() failed: -22
[ 3.715148] omap-abe-twl6040: probe of sound failed with error -22
Bisect pointed to a merge commit:
first bad commit: [0f688ab20a540aafa984c5dbd68a71debebf4d7f] Merge remote-tracking branch 'net-next/master'
and a diff between a working kernel does not reveal anything which would
explain the change in behavior.
Further investigation showed that on the second try of loading fails
because the dai_link->platform is no longer NULL and it might be pointing
to uninitialized memory.
The fix is to move the snd_soc_dai_link and snd_soc_card inside of the
abe_twl6040 struct, which is dynamically allocated every time the driver
probes.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently when snd_pcm_hw_constraint_integer fails there is
a memory leak of i2s_data on the error return path. Fix this by
kfree'ing i2s_data before returning.
Detected by CoverityScan, CID#1475479 ("Resource leak")
Fixes: 0b87d6bcd6 ("ASoC: amd: add acp3x pcm driver dma ops")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DAC output may be differential (default) or single-ended.
Signed-off-by: Kirill Marinushkin <kmarinushkin@birdec.tech>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the initial commit [1], I added differential output of the codec as
separate `+` and `-` widgets:
OUTL+
OUTR+
OUTL-
OUTR-
Later, in the commit [2], I added a device tree property to configure the
output as single-ended or differential. Having this property, the `+` and
`-` separation in widgets seems for me confusing. There are no functional
benefits in such separation, so I find reasonable to get rid of it:
OUTL
OUTR
The new naming is more friendly for sound cards, and is better aligned with
other codec drivers in kernel.
Renaming the output widgets now should not be a problem from the backwards-
compatibility perspective, as the driver for PCM3060 is added into the
mainline very recently, and did not yet appear in any releases.
[1] commit 6ee47d4a8d ("ASoC: pcm3060: Add codec driver")
[2] commit a78c62de00d5 ("ASoC: pcm3060: Add DT property for single-ended
output")
Signed-off-by: Kirill Marinushkin <kmarinushkin@birdec.tech>
Signed-off-by: Mark Brown <broonie@kernel.org>
sizeof() when applied to a pointer typed expression gives the
size of the pointer, not that of the pointed data.
Fixes: 8307b2afd3 ("ASoC: stm32: sai: set sai as mclk clock provider")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Frontend dai_link id is used for closing ADM sessions.
During concurrent usecase when one session is closed,
it closes other ADM session associated with other usecase
too. Dai_link->id should always point to Frontend dai id.
Set cpu_dai id as dai_link id to fix the issue.
Signed-off-by: Rohit kumar <rohitkr@codeaurora.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
sun8i-codec misses a route from ADC to AIF1 Slot 0 ADC. Add it
to the driver to avoid adding it to every dts.
Fixes: eda85d1fee ("ASoC: sun8i-codec: Add ADC support for a33")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ACP3x drivers can be built by selecting necessary kernel config option.
The patch enables build support of the same.
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Tested-by: Ravulapati Vishnu vardhan Rao <Vishnuvardhanrao.Ravulapati@amd.com>
Signed-off-by: Vijendar Mukunda <vijendar.mukunda@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When system wide suspend happens, ACP will be powered off.
When system resumes, all the runtime configuration data for
ACP needs to be programmed again.
Added 'resume'pm call back to ACP pm ops.
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Tested-by: Ravulapati Vishnu vardhan Rao <Vishnuvardhanrao.Ravulapati@amd.com>
Signed-off-by: Vijendar Mukunda <vijendar.mukunda@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ACP3x I2S (CPU DAI) can act in normal I2S and TDM modes.
Added support for TDM mode.
Desired mode can be selected from ASoC machine driver.
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Tested-by: Ravulapati Vishnu vardhan Rao <Vishnuvardhanrao.Ravulapati@amd.com>
Signed-off-by: Vijendar Mukunda <vijendar.mukunda@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ACP3x has a i2s controller block for playback and capture.
This patch adds ACP3x i2s DAI operations.
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Tested-by: Ravulapati Vishnu vardhan Rao <Vishnuvardhanrao.Ravulapati@amd.com>
Signed-off-by: Vijendar Mukunda <vijendar.mukunda@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ACP3x has a DMA controller to access system memory.
This controller transfers data from/to system memory
to/from the ACP internal FIFO.
The patch adds PCM driver DMA operations.
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Tested-by: Ravulapati Vishnu vardhan Rao <Vishnuvardhanrao.Ravulapati@amd.com>
Signed-off-by: Vijendar Mukunda <vijendar.mukunda@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Whenever audio data equal to the I2S FIFO watermark level are
produced/consumed, interrupt is generated.
Acknowledge the interrupt.
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Tested-by: Ravulapati Vishnu vardhan Rao <Vishnuvardhanrao.Ravulapati@amd.com>
Signed-off-by: Vijendar Mukunda <vijendar.mukunda@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
PCM platform driver binds to the platform device created by ACP3x PCI
device. PCM driver registers ALSA DMA and CPU DAI components with ASoC
framework.
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Tested-by: Ravulapati Vishnu vardhan Rao <Vishnuvardhanrao.Ravulapati@amd.com>
Signed-off-by: Vijendar Mukunda <vijendar.mukunda@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ACP 3x IP has I2S controller device as one of IP blocks.
Create a platform device for it, so that the PCM platform driver
can be bound to this device. Pass PCI resources like MMIO, irq
to the platform device.
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Tested-by: Ravulapati Vishnu vardhan Rao <vishnuvardhanrao.ravulapati@amd.com>
Signed-off-by: Vijendar Mukunda <vijendar.mukunda@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ACP 3.0 is a PCI audio device. This patch adds PCI driver to bind
to this device and get PCI resources.
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Signed-off-by: Sanju R Mehta <sanju.mehta@amd.com>
Tested-by: Ravulapati Vishnu vardhan Rao <Vishnuvardhanrao.Ravulapati@amd.com>
Signed-off-by: Vijendar Mukunda <vijendar.mukunda@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ACP 3.x is a new audio block in raven. Added register header
of the same.
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Signed-off-by: Vijendar Mukunda <vijendar.mukunda@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On certain platforms, Display HDMI HDA codec was not going to sleep state
after the use when links are powered down after turning off the display
power. As per the HW recommendation, links are powered down before turning
off the display power to ensure that the codec goes to sleep state.
This patch was updated from an earlier version submitted upstream [1]
which conflicted with the changes merged for HDaudio codec support
with the Intel DSP.
[1] https://patchwork.kernel.org/patch/10540213/
Signed-off-by: Sriram Periyasamy <sriramx.periyasamy@intel.com>
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add Icelake device id. Also, Icelake's pin2port mapping table is
complicated. So we use a mapping table to do the pin2port mapping.
Signed-off-by: Bard liao <bard.liao@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Factor out the duplicated initialization statements from
wm_adsp1_init() and wm_adsp2_init() into new function
wm_adsp_common_init().
The entire content of wm_adsp1_init() is the common code
but it is convenient to retain this exported function
to hide what we currently treat as common init (which might
change in the future) and also make clear the difference
between an ADSP1 entry point and common code.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Stack memory isn't DMA-safe so it isn't safe to use either
regmap_raw_read or regmap_bulk_read to read into stack memory.
The two functions to read the scratch registers were using
stack memory and regmap_raw_read. It's not worth allocating
memory just for this trivial read, and it isn't time-critical.
A simple regmap_read for each register is sufficient.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds missing prepare_sleve_config that is needed for
setup the DMA slave channel for I2S.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Initializing to -EINVAL is not correct as the variables are unsigned and
if buffer_size is 0 then they are not used anyway.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver will not probe if the pdata is not provided or created.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The mcbsp.c was copied a while back from arch/arm/plat-omap/mcbsp.c and it
contained a mix of McBSP and McBSP sidetone functions.
Create new file structure with the following split:
omap-mcbsp.c - McBSP related functions
omap-mcbsp-st.c - McBSP sidetone functionality
omap-mcbsp-priv.h - Private header for internal use
omap-mcbsp.h - Header for user drivers
I have tried to do the code move with minimal code change, cleanup patches
can be based on the new structure.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check if the McBSP have FIFO in the omap_mcbsp_set_threshold() and
omap_mcbsp_dai_delay() delay function to skip calling the lower layer if
it is not needed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We either start/stop TX or RX, never both. Move the tx/rx direction
selection within the functions.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The parameter name of dev_id is leftover from the old times when we passed
numeric ID as data for the interrupt handlers.
The mcbsp_rx and mcbsp_tx is misleading as they are pointers to the mcbsp
struct.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is configured runtime so no need to initialize it.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make the omap_mcbsp_dma_reg_params() a bit more intuitive to read for the
first glance by using SNDRV_PCM_STREAM_PLAYBACK/CAPTURE and to group the
outermost if case by stream direction.
While there, fix the outdated comment for the function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We need to call pci_iounmap() instead of iounmap() for the regions
obtained via pci_iomap() call for some archs that need special
treatment.
Fixes: aa31704fd8 ("ALSA: hda/ca0132: Add PCI region2 iomap for SBZ")
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HP Pavilion 15 (103c:820d) with ALC295 codec requires the quirk for
the mute LED control over mic3 pin. Added the corresponding quirk
entry.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=201653
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
All the recent support of Creative boards and onboard audio depend on
PCI, but they can't be trimmed easily even if you build without
CONFIG_PCI, since the quirk is detected dynamically and the code has
many branches with the flag check like spec->quirk type or
spec->use_alt_functions.
This patch makes these checks static for CONFIG_PCI=n case so that the
compiler optimizes out. The access to flags are replaced with macros
that are replaced with a static value for CONFIG_PCI=n.
The macros look slightly ugly for avoiding compiler warnings wrt
unused variables, and some additional default-case handlings for
another compiler warnings, but the rest are very straightforward
changes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
commit c0ea089dba ("ASoC: rsnd: rsnd_mod_name() handles both name and
ID") merged "name" and "ID" on rsnd_mod_name() to handle sub-ID
(= for CTU/BUSIF).
Then, it decided to share static char to avoid pointless memory.
But, it doesn't work correctry in below case, because last called
name will be used.
dev_xxx(dev, "%s is connected to %s\n",
rsnd_mod_name(mod_a), /* ssiu[00] */
rsnd_mod_name(mod_b)); /* ssi[0] */
->
rcar_sound ec500000.sound: ssi[0] is connected to ssi[0]
~~~~~~ ~~~~~~
We still don't want to have pointless memory, so let's use ring buffer.
16byte x 5 is very enough for this purpose.
dev_xxx(dev, "%s is connected to %s\n",
rsnd_mod_name(mod_a), /* ssiu[00] */
rsnd_mod_name(mod_b)); /* ssi[0] */
->
rcar_sound ec500000.sound: ssiu[00] is connected to ssi[0]
~~~~~~~~ ~~~~~~
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
drvdata is actually sun8i_codec, not snd_soc_card, so it crashes
when calling snd_soc_card_get_drvdata().
Drop card and scodec vars anyway since we don't need to
disable/unprepare clocks - it's already done by calling
runtime_suspend()
Drop clk_disable_unprepare() calls for the same reason.
Fixes: 36c684936f ("ASoC: Add sun8i digital audio codec")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
PCM OSS layer may allocate a few temporary buffers, one for the core
read/write and another for the conversions via plugins. Currently
both are allocated via vmalloc(). But as the allocation size is
equivalent with the PCM period size, the required size might be quite
small, depending on the application.
This patch replaces these vmalloc() calls with kvzalloc() for covering
small period sizes better. Also, we use "z"-alloc variant here for
addressing the possible uninitialized access reported by syzkaller.
Reported-by: syzbot+1cb36954e127c98dd037@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Gen2 has BUSIF0-3, Gen3 has BUSIF0-7 on some SSIU.
Current driver is assuming it is using BUSIF0 as default.
Thus, SSI is attaching SSIU (with BUSIF0) by using rsnd_ssiu_attach().
But, TDM split mode also needs other BUSIF to use it.
This patch adds missing SSIU BUSIFx support.
BUSIF is handled by SSIU instead of SSI anymore.
Thus, its settings no longer needed on SSI node on DT.
This patch removes its settings from Document, but driver is still
keeping compatibility. Thus, old DT style is still working.
But, to avoid confusing, it doesn't indicate old compatibility things on
Document. New SoC should have SSIU on DT from this patch.
1) old style DT is still supported (= no rcar_sound,ssiu node on DT)
2) If ssiu is not indicated on playback/capture,
BUSIF0 will be used as default
playback = <&ssi3>; /* ssiu30 will be selected */
3) you can select own ssiu
playback = <&ssi32 &ssi3>; /* ssiu32 will be selected */
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
converted rate/chan are handled each rated module, but
it will be used other module too.
For examle, converted channel is currently used for CTU,
but, it will be used for TDM Split mode, too.
This patch move/merge SRC/CTU hw_param under core.c
and handles converted rate/chan under rsnd_dai_stream.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current driver is supporting HDMI output, and its information
are handled under ssi.c. But, it is stream information.
Let's move it from ssi.c to core.c.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rdai->playback/rdai->capture are defined as io_playback/io_capture
on __rsnd_dai_probe(). Let's use it instead of original one.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver has rsnd_runtime_is_ssi_xxx() functions,
but it is not only related to SSI, thus, it is misunderstandable.
This patch renames it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DTC commit df536831d02c ("checks: add graph binding checks")
is checking endpoint bidirectional, and it is upstreamed to linux by
commit 50aafd6089 ("scripts/dtc: Update to upstream version
v1.4.6-21-g84e414b0b5bc").
Let's remove own bidirectional check
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current driver is checking situation that can not happen.
This patch removes over-kill check
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DTC commit df536831d02c ("checks: add graph binding checks")
is checking endpoint bidirectional, and it is upstreamed to linux by
commit 50aafd6089 ("scripts/dtc: Update to upstream version
v1.4.6-21-g84e414b0b5bc").
Let's remove own bidirectional check
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DTC commit df536831d02c ("checks: add graph binding checks")
is checking endpoint bidirectional, and it is upstreamed to linux by
commit 50aafd6089 ("scripts/dtc: Update to upstream version
v1.4.6-21-g84e414b0b5bc").
Let's remove own bidirectional check
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For some reason the RVP/LeafHill SSDT exposes an INT34C3 ID which is
used on other boards to point to the TDF8532 amplifier. Yay BIOS.
Add a DMI-quirk to ignore this ID and check for other valid machine
driver descriptors.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add firmware/topology information for APL RVP
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bard liao <bard.liao@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
GFP_ATOMIC is not required on any Intel drivers, use GFP_KERNEL
instead. A first cleanup was merged in April but missed a number
occurrences and new ones were added by copy/paste inertia.
While we are at it, make checkpatch happy with a sizeof(*msg)
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
s/skylaye/skylake
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't rely on internal Atom/SST-specific data structures, use
generic interface to let other drivers use the same machine drivers
as is, e.g. SOF to support BYT-CR devices
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't rely on internal Skylake-specific data structures, use
generic interface to let other drivers use the same machine driver
as is, e.g. SOF to support HDaudio codecs and HDMI outputs.
Tested on LeafHill CRB board, no regression seen with this change.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Enabling both the old AC97_BUS code and the new AC97_BUS_COMPAT causes
problems because both modules provide an exported snd_ac97_reset()
function.
I had tried to fix the problem of having both coexist earlier, but
my patch only prevented them from being built-in. This is because
of a special Kconfig feature that lets a symbol have a dependency
on another one being disabled, but still allow both to be loadable
modules.
Changing the dependency to =n avoids that problem, now we can only
build the new driver if the old one is completely disabled.
If we could figure out a way to let rename one of the reset
functions and have each driver link to exactly the old or
the compat code, that would also work, but I could not find if
that's possible.
Fixes: bec5ecdf41 ("ASoC: pxa: avoid AC97_BUS build warning")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The audio support is done via simple-audio-card via DT, the custom driver
is no longer needed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
"DACn Zero Flag" and "ADCn Overflow Flag" are read-only status
register. These information are needed for driver not for user.
Let's remove these from snd_kcontrol_new.
There is no detail explanation for these register on
datasheet, but, judging from its behavior, it seems these register
needs clock to read. Otherwise, I2C returns error.
Therefor, amixer command will be failed under non working timing.
Without this patch, user often fail amixer command.
This patch is tested on R-Car H3 ulcb-kf board, SSI3/4 TDM sound.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_component_update_bits() will only update the mask bits,
so remove the redundant snd_soc_component_read32().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For some reason the dapm widgets are incorrectly defined from the start,
Not sure how we ended up with such thing. Fix them now!
Without this fix the backend dais are always powered up even if there
is no active stream.
Reported-by: Jimmy Cheng-Yi Chiang <cychiang@google.com>
Reported-by: Rohit kumar <rohitkr@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
q6asm routing gets added multiple times as part of dai probe.
Move this to q6routing routes which has those widgets defined, this also
fixes the issue where these are added each time at dai probe.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The register map for CM6206 is known and we can define what
the values written to the different registers actually mean.
I tested to print the hex values before/after this change,
there is no functional change.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the commit c647f806b8 ("ALSA: hda - Allow multiple ADCs for
mic mute LED controls") we allow enabling the mic mute LED with
multiple ADCs. The commit changed the function return value to be
zero or a negative error, while this change was overlooked in the
thinkpad_acpi helper code where it still expects a positive return
value for success. This eventually leads to a NULL dereference on a
system that has only a mic mute LED.
This patch corrects the return value check in the corresponding code
as well.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=201621
Fixes: c647f806b8 ("ALSA: hda - Allow multiple ADCs for mic mute LED controls")
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
SD line mask for MI2S starts from BIT 0 instead of BIT 1.
Fix all bit mask for MI2S SD lines.
Signed-off-by: Rohit kumar <rohitkr@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some boards such as the Swanky model Chromebooks use pmc_plt_clk_0 for the
mclk instead of pmc_plt_clk_3.
This commit adds a DMI based quirk for this.
This fixing audio no longer working on these devices after
commit 648e921888 ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL")
that commit fixes us unnecessary keeping unused clocks on, but in case
of the Swanky that was breaking audio support since we were not using
the right clock in the cht_bsw_max98090_ti machine driver.
Cc: stable@vger.kernel.org
Fixes: 648e921888 ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL")
Reported-and-tested-by: Dean Wallace <duffydack73@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver is using "%s[%d]" for mod name and ID,
but, this ID portion might confusable.
For example currently, CTU ID is 0 to 7, but using 00 to 13
(= 00, 01, 02, 03, 10, 11, 12, 13) is very best matching to datasheet.
In the future, we will support BUSIFn, but it will be more complicated
numbering. To avoid future confusable code, this patch modify
rsnd_mod_name() to return understandable name.
To avoid using pointless memory, it uses static char and snprintf,
thus, rsnd_mod_name() user should use it immediately, and shouldn't keep
its pointer.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ID for CTU and SSIU are confusable.
1 CTU has 4 sub nodes. This means, CTU0 has CTU01 - CTU03, CTU1 has
CTU10 - CTU13. SSIU is more confusable. Gen2 SSIU has BUSIF0-3, Gen3
SSIU has BUSIF0-7, but not for all SSIU.
In rsnd driver, each mod drivers are assuming rsnd_mod_id() returns
main device ID (In CTU case CTU0-1, SSIU case SSIU0-9), not serial
number.
This patch adds new .id/.id_sub to handling more detail ID.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Each mod needs to have .get_status, but current driver is handling it
under rsnd_mod, instead of rsnd_mod_ops.
It is not any make sence. This patch moves it to rsnd_mod_ops, and
tidyup its parameter order to align to other callback functions.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
hw constraint for LEFT_J/I2S are same, but had duplicated code.
This code cleanup these.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For samples sizes of 20/24/32 bit the DRR2/DXR2 registers must be used to
receive or transmit the most significant part of the 32bit sample.
We can not trick the system by using the DRR2/DXR2 register offset and use
32bit element size since these (and other McBSP) registers are 16bit ones.
We would need support for port_window in cyclic mode from the sDMA driver,
but it is not straight forward as we would need to have the sDMA frame to
cover the 32bit (DRR2+DRR1/DXR2+DXR1), but the frames must cover the ALSA
period to be able to receive periodic interrupts.
Since the 32bit samples are not working (DMA timeout), just remove it in
case we have McBSP with reg_size of 2.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regulator_desc structure can be const as it is only passed as the
second argument of devm_regulator_register and the corresponding
parameter is declared as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
The snd_soc_dai_ops structures are only stored in the ops field of a
snd_soc_dai_driver structure, so make the snd_soc_dai_ops structures
const as well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
The snd_soc_dai_ops structures are only stored in the ops field of a
snd_soc_dai_driver structure, so make the snd_soc_dai_ops structures
const as well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
WARN_ON() already contains an unlikely(), so it's not necessary to use
unlikely.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Randconfig testing revealed a very old bug, with gcc-8:
sound/soc/intel/atom/sst/sst_loader.c: In function 'sst_load_fw':
sound/soc/intel/atom/sst/sst_loader.c:357:5: error: 'fw' may be used uninitialized in this function [-Werror=maybe-uninitialized]
if (fw == NULL) {
^
sound/soc/intel/atom/sst/sst_loader.c:354:25: note: 'fw' was declared here
const struct firmware *fw;
We must check the return code of request_firmware() before we look at the
pointer result that may be uninitialized when the function fails.
Fixes: 9012c9544e ("ASoC: Intel: mrfld - Add DSP load and management")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
gcc notices that without either the ac97 bus or the pdata, we never
initialize the regmap pointer, which leads to an uninitialized variable
access:
sound/soc/codecs/wm9712.c: In function 'wm9712_soc_probe':
sound/soc/codecs/wm9712.c:666:2: error: 'regmap' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Since that configuration is invalid, it's better to return an error
here. I tried to avoid adding complexity to the conditions, and turned
the #ifdef into a regular if(IS_ENABLED()) check for readability.
This in turn requires moving some header file declarations out of
an #ifdef.
The same code is used in three drivers, all of which I'm changing
the same way.
Fixes: 2ed1a8e0ce ("ASoC: wm9712: add ac97 new bus support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The snd_soc_ops structure can be const as it is only stored in the
ops field of a snd_soc_dai_link structure and this field is const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, the comparison of div < 0 is always false because div is
an unsigned int. Fix this by making div an int.
Detected by CoverityScan, CID#1475309 ("Unsigned compared against 0")
Fixes: 8307b2afd3 "(ASoC: stm32: sai: set sai as mclk clock provider")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SND_SUN50I_CODEC_ANALOG selects SND_SUNXI_ADDA_PR_REGMAP which is leftover
of renaming SND_SUNXI_ADDA_PR_REGMAP to SND_SUN8I_ADDA_PR_REGMAP. Replace
it with SND_SUN8I_ADDA_PR_REGMAP to fix possible link errors for some
configurations:
sound/soc/sunxi/sun50i-codec-analog.o: In function `sun50i_codec_analog_probe':
sun50i-codec-analog.c:(.text+0x62): undefined reference to `sun8i_adda_pr_regmap_init'
Fixes: 42371f327d ("ASoC: sunxi: Add new driver for Allwinner A64 codec's analog path controls")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A few device-specific fixes: a fix for SPDIF on old Creative PCI
board, and two additional fixes for the recent changes in FireWire
audio stack.
-----BEGIN PGP SIGNATURE-----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=lrUL
-----END PGP SIGNATURE-----
Merge tag 'sound-fix-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A few device-specific fixes: a fix for SPDIF on old Creative PCI
board, and two additional fixes for the recent changes in FireWire
audio stack"
* tag 'sound-fix-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: firewire-lib: fix insufficient PCM rule for period/buffer size
ALSA: ca0106: Disable IZD on SB0570 DAC to fix audio pops
ALSA: dice: fix to wait for releases of all ALSA character devices
Ever since commit 46e831abe8 ("drm/i915/lpe: Mark LPE audio runtime
pm as "no callbacks"") the runtime suspend/resume hooks are no longer
used. Inline them into the system suspend hooks.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181024154825.18185-2-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Takashi Iwai <tiwai@suse.de>
Commit 46e831abe8 ("drm/i915/lpe: Mark LPE audio runtime pm as
"no callbacks"") broke runtime PM with lpe audio. We can no longer
runtime suspend the GPU since the sysfs power/control for the
lpe-audio device no longer exists and the device is considered
always active. We can fix this by not marking the device as
active.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Fixes: 46e831abe8 ("drm/i915/lpe: Mark LPE audio runtime pm as "no callbacks"")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181024154825.18185-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Takashi Iwai <tiwai@suse.de>
commit 4d230d1271 ("ASoC: rsnd: fixup not to call clk_get/set under
non-atomic") fixuped clock start timing. But it exchanged clock start
checker from ssi->usrcnt to ssi->rate.
Current rsnd_ssi_master_clk_start() is called from .prepare,
but some player (for example GStreamer) might calls it many times.
In such case, the checker might returns error even though it was not
error. It should check ssi->usrcnt instead of ssi->rate.
This patch fixup it. Without this patch, GStreamer can't switch
48kHz / 44.1kHz.
Reported-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In a former commit, PCM constraint based on LCM of SYT_INTERVAL was
obsoleted with PCM rule. However, the new PCM rule brings -EINVAL in
some cases that max/min values of size of buffer/period is not
multiples of one of values of SYT_INTERVAL. For example, pulseaudio
always fail to configure PCM substream.
This commit changes strategy for the PCM rule. Although the buggy rules
had a single dependency (rate from period, period from rate, rate from
buffer, buffer from rate), a revised rule has double dependencies
(period from period/rate, buffer from buffer/rate). A step of value is
calculated with table of SYT_INTERVAL and list of available rates. This
prevents interval template which brings -EINVAL to a call of
snd_interval_refine().
Fixes: 5950229582bc('ALSA: firewire-lib: add PCM rules to obsolete PCM constraints based on LCM of SYT_INTERVAL')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Creative Audigy SE (SB0570) card currently exhibits an audible pop
whenever playback is stopped or resumed, or during silent periods of an
audio stream. Initialise the IZD bit to the 0 to eliminate these pops.
The Infinite Zero Detection (IZD) feature on the DAC causes the output
to be shunted to Vcap after 2048 samples of silence. This discharges the
AC coupling capacitor through the output and causes the aforementioned
pop/click noise.
The behaviour of the IZD bit is described on page 15 of the WM8768GEDS
datasheet: "With IZD=1, applying MUTE for 1024 consecutive input samples
will cause all outputs to be connected directly to VCAP. This also
happens if 2048 consecutive zero input samples are applied to all 6
channels, and IZD=0. It will be removed as soon as any channel receives
a non-zero input". I believe the second sentence might be referring to
IZD=1 instead of IZD=0 given the observed behaviour of the card.
This change should make the DAC initialisation consistent with
Creative's Windows driver, as this popping persists when initialising
the card in Linux and soft rebooting into Windows, but is not present on
a cold boot to Windows.
Signed-off-by: Alex Stanoev <alex@astanoev.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In a development period for Linux kernel v4.20, drivers in ALSA firewire
stack were changed to wait for releases of all ALSA character devices at
.remove callback of bus driver. However, ALSA dice driver is partly out
of this change. This bug can bring fault to user process which holds
the last of character device in unplugging.
This commit fixes the driver to wait in the callback.
Fixes: 61ccc6f6b2 ('ALSA: firewire: block .remove callback of bus driver till all of ALSA character devices are released')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There have been little changes in ALSA core stuff, but ASoC core still
kept rolling for the continued restructuring. The rest are lots of
small driver-specific changes and some minor API updates.
Here are highlights:
General:
- Appropriate fall-through annotations everywhere
- Some code cleanup in memalloc code, handling non-cacahed pages more
commonly in the helper
- Deployment of SNDRV_PCM_INFO_SYNC_APPLPTR flag consistently
Drivers:
- More HD-audio CA0132 codec improvement for supporting other Creative
boards
- Plumbing legacy HD-audio codecs as ASoC BE on Intel SST; this will
give move support of existing HD-audio devices with DSP
- A few device-specific HD-audio quirks as usual
- New quirk for RME CC devices and correction for B&W PX for USB-audio
- FireWire: code refactoring including devres usages
ASoC Core:
- Continued componentization works; it's almost done!
- A bunch of new for_each_foo macros
- Cleanups and fixes in DAPM code
ASoC Drivers:
- MCLK support for several different devices, including CS42L51, STM32
SAI, and MAX98373
- Support for Allwinner A64 CODEC analog, Intel boards with DA7219 and
MAX98927, Meson AXG PDM inputs, Nuvoton NAU8822, Renesas R8A7744 and
TI PCM3060
-----BEGIN PGP SIGNATURE-----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=3LrT
-----END PGP SIGNATURE-----
Merge tag 'sound-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"There have been little changes in ALSA core stuff, but ASoC core still
kept rolling for the continued restructuring. The rest are lots of
small driver-specific changes and some minor API updates. Here are
highlights:
General:
- Appropriate fall-through annotations everywhere
- Some code cleanup in memalloc code, handling non-cacahed pages more
commonly in the helper
- Deployment of SNDRV_PCM_INFO_SYNC_APPLPTR flag consistently
Drivers:
- More HD-audio CA0132 codec improvement for supporting other Creative
boards
- Plumbing legacy HD-audio codecs as ASoC BE on Intel SST; this will
give move support of existing HD-audio devices with DSP
- A few device-specific HD-audio quirks as usual
- New quirk for RME CC devices and correction for B&W PX for USB-audio
- FireWire: code refactoring including devres usages
ASoC Core:
- Continued componentization works; it's almost done!
- A bunch of new for_each_foo macros
- Cleanups and fixes in DAPM code
ASoC Drivers:
- MCLK support for several different devices, including CS42L51, STM32
SAI, and MAX98373
- Support for Allwinner A64 CODEC analog, Intel boards with DA7219 and
MAX98927, Meson AXG PDM inputs, Nuvoton NAU8822, Renesas R8A7744 and
TI PCM3060"
* tag 'sound-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (299 commits)
ASoC: stm32: sai: fix master clock naming
ASoC: stm32: add clock dependency for sai
ALSA: hda/ca0132 - Actually fix microphone issue
ASoC: sun4i-i2s: move code from startup/shutdown hooks into pm_runtime hooks
ASoC: wm2000: Remove wm2000_read helper function
ASoC: cs42l51: fix mclk support
ASoC: wm_adsp: Log addresses as 8 digits in wm_adsp_buffer_populate
ASoC: wm_adsp: Rename memory fields in wm_adsp_buffer
ASoC: cs42l51: add mclk support
ASoC: stm32: sai: set sai as mclk clock provider
ASoC: dt-bindings: add mclk support to cs42l51
ASoC: dt-bindings: add mclk provider support to stm32 sai
ASoC: soc-core: fix trivial checkpatch issues
ASoC: dapm: Add support for hw_free on CODEC to CODEC links
ASoC: Intel: kbl_da7219_max98927: minor white space clean up
ALSA: i2c/cs8427: Fix int to char conversion
ALSA: doc: Brush up the old writing-an-alsa-driver
ASoC: rsnd: tidyup SSICR::SWSP for TDM
ASoC: rsnd: enable TDM settings for SSI parent
ASoC: pcm3168a: add hw constraint for capture channel
...
sound/soc/stm/stm32_sai_sub.c:393:26-32: ERROR: application of sizeof to pointer
sizeof when applied to a pointer typed expression gives the size of
the pointer
Generated by: scripts/coccinelle/misc/noderef.cocci
Fixes: 8307b2afd3 ("ASoC: stm32: sai: set sai as mclk clock provider")
CC: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A couple of fixes for build bot issues in the STM32 SAI driver.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlvPB6ETHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0AolB/9nKMIGJqCZWWLh+Rq1dAc1k3+cOkuU
4Culg5XaTn9uS9Tu5DJKotk8SC4zvblbC4JiQPVisuUm1EY/ADwsu92DeC3xB3w4
iEyep1H1UzM8um/uuPe0lMWalNBFCsNRih0ZETxLh1ZK2hJlUtCYHz0n5ewmq/6R
QVdkAtm8oMll1LhTu9x95+ozYp33IxFpDVjSDXDZcWbgg93wBZ6dUMVLeREOK+Vl
h2H4TVgN/frJyBdKDBItCLVyL9e5ygw6UioEi4vgy08q1Kw01RKmRA86dScgBXaY
NVCi8OAVqQKoO0j5ChISnJPX3SmVV/5f6K+0x1to5bqfGOwOmoqCbOSB
=jBs9
-----END PGP SIGNATURE-----
Merge tag 'asoc-v5.0-2' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Additional fixes for the next release
A couple of fixes for build bot issues in the STM32 SAI driver.
Pull perf updates from Ingo Molnar:
"The main updates in this cycle were:
- Lots of perf tooling changes too voluminous to list (big perf trace
and perf stat improvements, lots of libtraceevent reorganization,
etc.), so I'll list the authors and refer to the changelog for
details:
Benjamin Peterson, Jérémie Galarneau, Kim Phillips, Peter
Zijlstra, Ravi Bangoria, Sangwon Hong, Sean V Kelley, Steven
Rostedt, Thomas Gleixner, Ding Xiang, Eduardo Habkost, Thomas
Richter, Andi Kleen, Sanskriti Sharma, Adrian Hunter, Tzvetomir
Stoyanov, Arnaldo Carvalho de Melo, Jiri Olsa.
... with the bulk of the changes written by Jiri Olsa, Tzvetomir
Stoyanov and Arnaldo Carvalho de Melo.
- Continued intel_rdt work with a focus on playing well with perf
events. This also imported some non-perf RDT work due to
dependencies. (Reinette Chatre)
- Implement counter freezing for Arch Perfmon v4 (Skylake and newer).
This allows to speed up the PMI handler by avoiding unnecessary MSR
writes and make it more accurate. (Andi Kleen)
- kprobes cleanups and simplification (Masami Hiramatsu)
- Intel Goldmont PMU updates (Kan Liang)
- ... plus misc other fixes and updates"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (155 commits)
kprobes/x86: Use preempt_enable() in optimized_callback()
x86/intel_rdt: Prevent pseudo-locking from using stale pointers
kprobes, x86/ptrace.h: Make regs_get_kernel_stack_nth() not fault on bad stack
perf/x86/intel: Export mem events only if there's PEBS support
x86/cpu: Drop pointless static qualifier in punit_dev_state_show()
x86/intel_rdt: Fix initial allocation to consider CDP
x86/intel_rdt: CBM overlap should also check for overlap with CDP peer
x86/intel_rdt: Introduce utility to obtain CDP peer
tools lib traceevent, perf tools: Move struct tep_handler definition in a local header file
tools lib traceevent: Separate out tep_strerror() for strerror_r() issues
perf python: More portable way to make CFLAGS work with clang
perf python: Make clang_has_option() work on Python 3
perf tools: Free temporary 'sys' string in read_event_files()
perf tools: Avoid double free in read_event_file()
perf tools: Free 'printk' string in parse_ftrace_printk()
perf tools: Cleanup trace-event-info 'tdata' leak
perf strbuf: Match va_{add,copy} with va_end
perf test: S390 does not support watchpoints in test 22
perf auxtrace: Include missing asm/bitsperlong.h to get BITS_PER_LONG
tools include: Adopt linux/bits.h
...
Fixes: 8307b2afd3 ("ASoC: stm32: sai: set sai as mclk clock provider")
Fix warning issued by strncat when bound equals to source length.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes: 8307b2afd3 ("ASoC: stm32: sai: set sai as mclk clock provider")
Add COMMON_CLK dependency for STM32 SAI,
as it is required by clock provider.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As ever there's a lot of small and driver specific changes going on
here, but we do also have some relatively large changes in the core
thanks to the hard work of Charles and Morimoto-san:
- More component transitions from Morimoto-san, I think we're about
finished with this. Thanks for all the hard work!
- Morimoto-san also added a bunch of for_each_foo macros
- A bunch of cleanups and fixes for DAPM from Charles.
- MCLK support for several different devices, including CS42L51, STM32
SAI, and MAX98373.
- Support for Allwinner A64 CODEC analog, Intel boards with DA7219 and
MAX98927, Meson AXG PDM inputs, Nuvoton NAU8822, Renesas R8A7744 and
TI PCM3060.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlvNuPoTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0CsxB/91P2RgcUhBSkPO3jsFSerc+RccqD8j
XogqjC62V2T3xqVUYtqqLf0dZFKUPFNoFitN2XdNU36H55DVI+3wxxmwObc64RIc
uB6ptQuwFz7vGeF6r6GWFUAZ7MB518dq/oZYRKrjAW49Lt2YiCD0HJ2gi+0Hm66A
53I7SLH3Q386UHDd+dl7+9BN7gPt0OIKAdsc/Vq7BDYvP+cNEm+YYjXGwaHjLLEC
o8vmj8Ny6x0dytdYuQ/XuekBhGopcfqTbWTpTu43/jCd5rumQXQY2g9CC1eRMlEJ
cm1hOjAErmKkkg2S84B1cMAvK23Szu36sPyeCphSQWOhlL4CFPVyJqic
=9A07
-----END PGP SIGNATURE-----
Merge tag 'asoc-v5.0' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v5.0/v4.20
As ever there's a lot of small and driver specific changes going on
here, but we do also have some relatively large changes in the core
thanks to the hard work of Charles and Morimoto-san:
- More component transitions from Morimoto-san, I think we're about
finished with this. Thanks for all the hard work!
- Morimoto-san also added a bunch of for_each_foo macros
- A bunch of cleanups and fixes for DAPM from Charles.
- MCLK support for several different devices, including CS42L51, STM32
SAI, and MAX98373.
- Support for Allwinner A64 CODEC analog, Intel boards with DA7219 and
MAX98927, Meson AXG PDM inputs, Nuvoton NAU8822, Renesas R8A7744 and
TI PCM3060.
This patch fixes the microphone issue for all cards. The previous fix
worked on the ZxR, but not on the AE-5 or Z. This patch has been tested
to work for all cards.
Signed-off-by: Connor McAdams <conmanx360@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
startup() and shutdown() hooks are called for both substreams,
so stopping either substream when another is running breaks the
latter.
E.g. playback breaks if capture is stopped when playback is running.
Move code from startup() and shutdown() to resume() and suspend()
hooks respectively to fix this issue
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The return type "unsigned int" was used by the wm2000_read()
function despite of the aspect that it will eventually return
a negative error code.
The resulting function doesn't add much to the code, so replace
wm2000_read with regmap_read.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The MCLK clock is made optional for cs42l51 codec.
However, ASoC DAPM clock supply widget, expects the clock to be defined
unconditionally.
Register MCLK DAPM conditionally in codec driver,
depending on clock presence in DT.
Fixes: 5e8d63a726 ("ASoC: cs42l51: add mclk support")
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Increase the address value width in the debug log from 4 digits to
8 digits to allow for DSP cores with larger memory address ranges.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The wm_adsp_buffer struct is the control header of a circular
buffer used to transfer data from the firmware over the
control interface to an ALSA compressed stream.
The original names of the fields pointing to the data buffer
were based on ADSP2V2 memory layout where they correspond to
{XM, XM, YM}. But this circular buffer could be used on other
types of DSP core that have different memory region types.
Also the names and description of the size fields were not
very clear. The field names and descriptions have been changed
to be generic and not imply any particular memory types.
This patch updates the wm_adsp driver to the new field names.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add MCLK dapm to allow configuration of cirrus CS42l51
codec as a master clock consumer.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add master clock generation support in STM32 SAI.
The master clock provided by SAI can be used to feed a codec.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix a few trivial aka cosmetic only checkpatch issues like long lines,
wrong indentations, spurious blanks and newlines, missing newlines,
multi-line comments etc.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, on power down for a CODEC to CODEC DAI link we only call
digital_mute and shutdown. Provide a little more flexibility for drivers
by adding a call to hw_free as well.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Compiling with clang yields the following warning:
sound/i2c/cs8427.c:140:31: warning: implicit conversion from 'int'
to 'char' changes value from 160 to -96 [-Wconstant-conversion]
data[0] = CS8427_REG_AUTOINC | CS8427_REG_CORU_DATABUF;
~ ~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~
Because CS8427_REG_AUTOINC is defined as 128, it is too big for a
char field.
So change data from char to unsigned char, that it can hold the value.
This patch does not change the generated code.
Signed-off-by: Philipp Klocke <philipp97kl@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
R-Car datasheet is indicating that WS output settings of SSICR::SWSP
is inverted on TDM mode from non TDM mode settings.
But, it is meaning that TDM should use 0 here.
Without this patch, sound input/output 1ch will be 2ch, 2ch will be 3ch
..., be jumbled on I2S + TDM settings. This patch fixup it.
This patch is tested on R-Car H3 ulcb-kf board, SSI3/4 TDM sound.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some SSIs are sharing each pins (= WS/CLK pin for playback/capture).
Then, SSI parent needs control WS/CLK setting for SSI slave.
In such case, SSI parent needs TDM settings if SSI slave is working as
TDM mode. But it is not cared in current driver.
It can't capture TDM sound without this patch if SSIs were pin sharing.
This patch is tested on R-Car H3 ulcb-kf board, SSI3/4 with TDM sound.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
LEFT_J / I2S only can use TDM.
commit 594680ea4a ("ASoC: pcm3168a: add hw constraint for channel")
commit 3809688980 ("ASoC: pcm3168a: add HW constraint for non
RIGHT_J") added channel constraint for it, but, it was only for playback.
This patch adds constraint for capture.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The STA32x chips feature an XTI clock input that needs to be stable before
the reset signal is released. Therefore, the chip driver needs to get a
handle to the clock. Instead of relying on other parts of the system to
enable the clock, let the codec driver grab a handle itself.
In order to keep existing boards working, clock support is made optional.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Similar to the following:
commit 4321723648 ("ASoC: tegra_alc5632: fix device_node refcounting")
commit 7c5dfd5496 ("ASoC: tegra: fix device_node refcounting")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allwinner A64 uses the same digital codec part as in A33, so we need
to build this driver on ARM64 as well.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The internal codec on A64 is split into 2 parts. The analog path controls
are routed through an embedded custom register bus accessed through
the PRCM block.
Add an ASoC component driver for it. This should be tied to the codec
audio card as an auxiliary device.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It will be reused by sun50i-codec-analog later.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
BCLK / LRCK ratio should be sample size * channels, but it was
hardcoded to 32 (0x1 is 32 as per A33 and A64 datasheets).
Calculate it basing on sample size and number of channels.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The I2S block used for the audio codec in the A64 differs from other 3
I2S modules in A64 and isn't compatible with H3. But it is very similar
to what is found in A10(sun4i). However, its TX FIFO is
located at a different address.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DMA API does its own zone decisions based on the coherent_dma_mask.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Power-saving is causing plops on audio start/stop on Dell Precision T3600
laptops and Intel DZ77BH boards, add these to the power_save blacklist.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1525104
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds da7219_max98927 machine driver entry into
machine table
Signed-off-by: Mac Chiang <mac.chiang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds Kabylake I2S machine driver with:
DA7219 audio codec(SSP1) and MAXIM98927(SSP0) speaker amplifier.
Signed-off-by: Mac Chiang <mac.chiang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some 3 pole connectors report impedance greater than threshold of
1000Ohm. Thus, da7219 reports them as LINEOUT.
Adding the SND_JACK_LINEOUT type so that we don't fail to detect
any 3 pole jack type.
Also, changing
SND_JACK_HEADPHONE | SND_JACK_MICROPHONE -> SND_JACK_HEADSET
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DMA API does its own zone decisions based on the coherent_dma_mask.
[ Note: as the driver doesn't set the DMA coherent mask, we can assume
the default 32bit DMA, hence it should be safe to drop the flag here
-- tiwai ]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
pcm3168a is supporting TDM on I2S/Left_J, but there is no
settings for it. This patch add it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
LEFT_J / I2S only can use TDM.
This patch adds channel constraint for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
RIGHT_J only can handle 16bit data bits.
Current driver just errored if user requests non RIGHT_J
+ 16bit combination. But it is not useful for user.
This patch adds HW constraint for it, and avoid
error on such situation.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ESD watchdog code in sta32x_watchdog() dereferences the pointer
which is never assigned.
This is a regression from a1be4cead9 ("ASoC: sta32x: Convert to direct
regmap API usage.") which went unnoticed since nobody seems to use that ESD
workaround.
Fixes: a1be4cead9 ("ASoC: sta32x: Convert to direct regmap API usage.")
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
As a preparatory patch for the upcoming -Wimplicit-fallthrough
compiler checks, add the "fall through" annotation in au88xx driver.
Although the usages in both both functions vortex_adbdma_setbuffers()
and vortex_wtdma_setbuffers() look a bit suspicious, we keep the
behavior as before, just to be safer. If it were broken, we should
have already received bug reports.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As a preparatory patch for the upcoming -Wimplicit-fallthrough
compiler checks, replace with the standard "fall through" annotation
at the right places. They have to be put right before the next
labels.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As a preparatory patch for the upcoming -Wimplicit-fallthrough
compiler checks, replace with the standard "fall through" annotation.
Unfortunately gcc doesn't understand a chattier text.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As a preparatory patch for the upcoming -Wimplicit-fallthrough
compiler checks, add the "fall through" annotation in caiaq driver.
Note that this seems necessary to be put exactly before the next
label, so it's outside the ifdef block.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As a preparatory patch for the upcoming -Wimplicit-fallthrough
compiler checks, add the "fall through" annotation in
snd_dma_alloc_pages(). Note that this seems necessary to be put
exactly before the next label, so it's outside the ifdef block.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In some error paths, reference count of firewire unit is not decreased.
This commit fixes the bug.
Fixes: 5b14ec25a79b('ALSA: firewire: release reference count of firewire unit in .remove callback of bus driver')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Lenovo G50-30, like other G50 models, has a Conexant codec that
requires a quirk for its inverted stereo dmic.
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1249364
Reported-by: Alexander Ploumistos <alex.ploumistos@gmail.com>
Tested-by: Alexander Ploumistos <alex.ploumistos@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jeremy Cline <jcline@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Current audio-graph-card is supporting mclk-fs on CPU node
side only. But having Codec node also is good idea.
It will be just ignored if not defined.
"rcpu_ep" is same as "cpu_ep", This patch tidyup it, too.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit fb2815f44a ("ASoC: rsnd: add support for 16/24 bit slot widths")
added TDM width check, and return error if it was not 16/24/32 bit.
But it is too strict. This patch uses 32bit same as default.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
max98988 only builds with I2C support enabled, otherwise we get a build error:
sound/soc/codecs/max98088.c:1789:1: error: data definition has no type or storage class [-Werror]
module_i2c_driver(max98088_i2c_driver);
^~~~~~~~~~~~~~~~~
sound/soc/codecs/max98088.c:1789:1: error: type defaults to 'int' in declaration of 'module_i2c_driver' [-Werror=implicit-int]
sound/soc/codecs/max98088.c:1789:1: error: parameter names (without types) in function declaration [-Werror]
sound/soc/codecs/max98088.c:1780:26: error: 'max98088_i2c_driver' defined but not used [-Werror=unused-variable]
Fixes: 24ae67c582 ("ASoC: max98988: make it selectable")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
In former commits, .private_free callback releases resources just for
data transmission. This release function can be called without the
resources are actually allocated in error paths.
This commit applies a small refactoring to clean up codes in error
paths.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In drivers of ALSA firewire stack, bebob and fireworks drivers have
local device entry table. At present, critical section to operate the
table is from the beginning/end of 'do_registration' call. This can be
more narrow and simplify codes.
This commit applies small refactoring for the above purpose.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In a previous commit, drivers in ALSA firewire stack blocks .remove
callback of bus driver. This enables to release members of private
data in the callback after releasing device of sound card.
This commit simplifies codes to release the members.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
At present, in .remove callback of bus driver just decrease reference
count of device for ALSA card instance. This delegates release of the
device to a process in which the last of ALSA character device is
released.
On the other hand, the other drivers such as for devices on PCIe are
programmed to block .remove callback of bus driver till all of ALSA
character devices are released.
For consistency of behaviour for whole drivers, this probably confuses
users. This commit takes drivers in ALSA firewire stack to imitate the
above behaviour.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The front MIC on the Lenovo M715 can't record sound, after applying
the ALC294_FIXUP_LENOVO_MIC_LOCATION, the problem is fixed. So add
the pin configuration of this machine to the pin quirk table.
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BIOS on ASUS G751 doesn't seem to map the headphone pin (NID 0x16)
correctly. Add a quirk to address it, as well as chaining to the
previous fix for the microphone.
Reported-by: Håvard <hovardslill@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch removes the echo cancellation control for desktop cards, and
makes use of the special 0x47 SCP command for noise reduction.
Signed-off-by: Connor McAdams <conmanx360@gmail.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch cleans up the patch_ca0132() function with suggestions from
Takashi Sakamoto.
Signed-off-by: Connor McAdams <conmanx360@gmail.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch fixes microphone inconsistency issues by adding a delay to
each setup_defaults function. Without this, the microphone only works
intermittently.
Signed-off-by: Connor McAdams <conmanx360@gmail.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently the driver will build only if SND_SOC_ALL_CODECS is set.
Adding a Kconfig menu description to build the driver standalone.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
If master clock is provided through device tree, then update
the master clock frequency during set_sysclk.
Cc: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Tushar Behera <trblinux@gmail.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
[m.felsch@pengutronix.de: move mclk request to i2c_probe]
[m.felsch@pengutronix.de: make use of snd_soc_component_get_bias_level()]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Lookup regulators for Vdd and Vdda during probe, and enable them when the
component is linked.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a corresponding model list entry for ASUS G751 so that user can
test the quirk for another compatible machines more easily.
Reported-and-tested-by: Håvard <hovardslill@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASUS G751 requires the extra COEF initialization to make it microphone
working properly.
Reported-and-tested-by: Håvard <hovardslill@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As a preparatory patch for the upcoming -Wimplicit-fallthrough
compiler checks, replace with the standard "fall through" annotation.
gcc can't understand the mixed texts, unfortunately.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
As a preparatory patch for the upcoming -Wimplicit-fallthrough
compiler checks, add the "fall through" annotation in Intel SST
skylake driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
As a preparatory patch for the upcoming -Wimplicit-fallthrough
compiler checks, add the "fall through" annotations in rt274 driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
As a preparatory patch for the upcoming -Wimplicit-fallthrough
compiler checks, replace with the standard "fall through" annotation.
Unfortunately gcc doesn't understand the mixed comment lines.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
As a preparatory patch for the upcoming -Wimplicit-fallthrough
compiler checks, replace with the standard "fall through" annotation
at the right place. It has to be put right before the next label.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adds several vendor specific mixer quirks for RME's Class Compliant
USB devices. These provide extra status information from the device
otherwise not available.
These include AES/SPDIF rate and status information, current system
sampling rate and measured frequency. This information is especially
useful in cases where device's clock is slaved to external clock
source.
Signed-off-by: Jussi Laako <jussi@sonarnerd.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A quirk in snd-usb-audio was added to automate setting sample rate to
4800k and remove the previously exposed nonfunctional microphone for
the Bowers & Wilkins PX:
commit 240a8af929https://lore.kernel.org/patchwork/patch/919689/
However the headphones where updated shortly after that to remove the
unintentional microphone functionality. I guess because of this the
headphones now crash when connecting them via USB while the quirk is
active. Dmesg:
snd-usb-audio: probe of 2-3:1.0 failed with error -22
usb 2-3: 2:1: cannot get min/max values for control 2 (id 2)
This patch removes the microfone and allows the headphones to connect
and work out of the box. It is based on the current mainline kernel
and successfully applied an tested on my machine (4.18.10.arch1-1).
Fixes: 240a8af929 ("ALSA: usb-audio: Add a quirck for B&W PX headphones")
Signed-off-by: Nicolas Huaman <nicolas@herochao.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Elo VuPoint 15MX has two headphone jacks of which neither work by
default. Disabling automute allows ALSA to work normally with the
speakers & left headphone jack.
Future pin configuration changes may be required in the future to get
the right headphone jack working in tandem.
Signed-off-by: Michael Pobega <mpobega@neverware.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For discarding the pending bytes on rawmidi, we process with a loop of
snd_rawmidi_transmit() which is just a waste of CPU power.
Implement a lightweight API function to discard the pending bytes and
the proceed the ring buffer instantly, and use it instead of open
codes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The driver already has support for setting the FDRB bit in the CONFA
register through platform data, but there was no property to set it
in the device-tree bindings.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
If a "extclk" clock is given, enable and disable it when appropriate.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Jiada Wang