Impose a limit on the number of watches that a user can hold so that
they can't use this mechanism to fill up all the available memory.
This is done by putting a counter in user_struct that's incremented when
a watch is allocated and decreased when it is released. If the number
exceeds the RLIMIT_NOFILE limit, the watch is rejected with EAGAIN.
This can be tested by the following means:
(1) Create a watch queue and attach it to fd 5 in the program given - in
this case, bash:
keyctl watch_session /tmp/nlog /tmp/gclog 5 bash
(2) In the shell, set the maximum number of files to, say, 99:
ulimit -n 99
(3) Add 200 keyrings:
for ((i=0; i<200; i++)); do keyctl newring a$i @s || break; done
(4) Try to watch all of the keyrings:
for ((i=0; i<200; i++)); do echo $i; keyctl watch_add 5 %:a$i || break; done
This should fail when the number of watches belonging to the user hits
99.
(5) Remove all the keyrings and all of those watches should go away:
for ((i=0; i<200; i++)); do keyctl unlink %:a$i; done
(6) Kill off the watch queue by exiting the shell spawned by
watch_session.
Fixes: c73be61ced ("pipe: Add general notification queue support")
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a helper that waits for a pid and stores the status in the passed in
kernel pointer. Use it to fix the usage of kernel_wait4 in
call_usermodehelper_exec_sync that only happens to work due to the
implicit set_fs(KERNEL_DS) for kernel threads.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Link: http://lkml.kernel.org/r/20200721130449.5008-1-hch@lst.de
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current_gfp_context() converts a number of PF_MEMALLOC_* per-process
flags into the corresponding GFP_* flags for memory allocation. In that
function, current->flags is accessed 3 times. That may lead to duplicated
access of the same memory location.
This is not usually a problem with minimal debug config options on as the
compiler can optimize away the duplicated memory accesses. With most of
the debug config options on, however, that may not be the case. For
example, the x86-64 object size of the __need_fs_reclaim() in a debug
kernel that calls current_gfp_context() was 309 bytes. With this patch
applied, the object size is reduced to 202 bytes. This is a saving of 107
bytes and will probably be slightly faster too.
Use READ_ONCE() to access current->flags to prevent the compiler from
possibly accessing current->flags multiple times.
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Michel Lespinasse <walken@google.com>
Link: http://lkml.kernel.org/r/20200618212936.9776-1-longman@redhat.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, memalloc_nocma_{save/restore} API that prevents CMA area
in page allocation is implemented by using current_gfp_context(). However,
there are two problems of this implementation.
First, this doesn't work for allocation fastpath. In the fastpath,
original gfp_mask is used since current_gfp_context() is introduced in
order to control reclaim and it is on slowpath. So, CMA area can be
allocated through the allocation fastpath even if
memalloc_nocma_{save/restore} APIs are used. Currently, there is just
one user for these APIs and it has a fallback method to prevent actual
problem.
Second, clearing __GFP_MOVABLE in current_gfp_context() has a side effect
to exclude the memory on the ZONE_MOVABLE for allocation target.
To fix these problems, this patch changes the implementation to exclude
CMA area in page allocation. Main point of this change is using the
alloc_flags. alloc_flags is mainly used to control allocation so it fits
for excluding CMA area in allocation.
Fixes: d7fefcc8de (mm/cma: add PF flag to force non cma alloc)
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Roman Gushchin <guro@fb.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: "Aneesh Kumar K . V" <aneesh.kumar@linux.ibm.com>
Link: http://lkml.kernel.org/r/1595468942-29687-1-git-send-email-iamjoonsoo.kim@lge.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRAhzRXHqcMeLMyaSiRxhvAZXjcogUCXyge/QAKCRCRxhvAZXjc
oildAQCCWpnTeXm6hrIE3VZ36X5npFtbaEthdBVAUJM7mo0FYwEA8+Wbnubg6jCw
mztkXCnTfU7tApUdhKtQzcpEws45/Qk=
=REE/
-----END PGP SIGNATURE-----
Merge tag 'fork-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux
Pull fork cleanups from Christian Brauner:
"This is cleanup series from when we reworked a chunk of the process
creation paths in the kernel and switched to struct
{kernel_}clone_args.
High-level this does two main things:
- Remove the double export of both do_fork() and _do_fork() where
do_fork() used the incosistent legacy clone calling convention.
Now we only export _do_fork() which is based on struct
kernel_clone_args.
- Remove the copy_thread_tls()/copy_thread() split making the
architecture specific HAVE_COYP_THREAD_TLS config option obsolete.
This switches all remaining architectures to select
HAVE_COPY_THREAD_TLS and thus to the copy_thread_tls() calling
convention. The current split makes the process creation codepaths
more convoluted than they need to be. Each architecture has their own
copy_thread() function unless it selects HAVE_COPY_THREAD_TLS then it
has a copy_thread_tls() function.
The split is not needed anymore nowadays, all architectures support
CLONE_SETTLS but quite a few of them never bothered to select
HAVE_COPY_THREAD_TLS and instead simply continued to use copy_thread()
and use the old calling convention. Removing this split cleans up the
process creation codepaths and paves the way for implementing clone3()
on such architectures since it requires the copy_thread_tls() calling
convention.
After having made each architectures support copy_thread_tls() this
series simply renames that function back to copy_thread(). It also
switches all architectures that call do_fork() directly over to
_do_fork() and the struct kernel_clone_args calling convention. This
is a corollary of switching the architectures that did not yet support
it over to copy_thread_tls() since do_fork() is conditional on not
supporting copy_thread_tls() (Mostly because it lacks a separate
argument for tls which is trivial to fix but there's no need for this
function to exist.).
The do_fork() removal is in itself already useful as it allows to to
remove the export of both do_fork() and _do_fork() we currently have
in favor of only _do_fork(). This has already been discussed back when
we added clone3(). The legacy clone() calling convention is - as is
probably well-known - somewhat odd:
#
# ABI hall of shame
#
config CLONE_BACKWARDS
config CLONE_BACKWARDS2
config CLONE_BACKWARDS3
that is aggravated by the fact that some architectures such as sparc
follow the CLONE_BACKWARDSx calling convention but don't really select
the corresponding config option since they call do_fork() directly.
So do_fork() enforces a somewhat arbitrary calling convention in the
first place that doesn't really help the individual architectures that
deviate from it. They can thus simply be switched to _do_fork()
enforcing a single calling convention. (I really hope that any new
architectures will __not__ try to implement their own calling
conventions...)
Most architectures already have made a similar switch (m68k comes to
mind).
Overall this removes more code than it adds even with a good portion
of added comments. It simplifies a chunk of arch specific assembly
either by moving the code into C or by simply rewriting the assembly.
Architectures that have been touched in non-trivial ways have all been
actually boot and stress tested: sparc and ia64 have been tested with
Debian 9 images. They are the two architectures which have been
touched the most. All non-trivial changes to architectures have seen
acks from the relevant maintainers. nios2 with a custom built
buildroot image. h8300 I couldn't get something bootable to test on
but the changes have been fairly automatic and I'm sure we'll hear
people yell if I broke something there.
All other architectures that have been touched in trivial ways have
been compile tested for each single patch of the series via git rebase
-x "make ..." v5.8-rc2. arm{64} and x86{_64} have been boot tested
even though they have just been trivially touched (removal of the
HAVE_COPY_THREAD_TLS macro from their Kconfig) because well they are
basically "core architectures" and since it is trivial to get your
hands on a useable image"
* tag 'fork-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
arch: rename copy_thread_tls() back to copy_thread()
arch: remove HAVE_COPY_THREAD_TLS
unicore: switch to copy_thread_tls()
sh: switch to copy_thread_tls()
nds32: switch to copy_thread_tls()
microblaze: switch to copy_thread_tls()
hexagon: switch to copy_thread_tls()
c6x: switch to copy_thread_tls()
alpha: switch to copy_thread_tls()
fork: remove do_fork()
h8300: select HAVE_COPY_THREAD_TLS, switch to kernel_clone_args
nios2: enable HAVE_COPY_THREAD_TLS, switch to kernel_clone_args
ia64: enable HAVE_COPY_THREAD_TLS, switch to kernel_clone_args
sparc: unconditionally enable HAVE_COPY_THREAD_TLS
sparc: share process creation helpers between sparc and sparc64
sparc64: enable HAVE_COPY_THREAD_TLS
fork: fold legacy_clone_args_valid() into _do_fork()
Pull execve updates from Eric Biederman:
"During the development of v5.7 I ran into bugs and quality of
implementation issues related to exec that could not be easily fixed
because of the way exec is implemented. So I have been diggin into
exec and cleaning up what I can.
This cycle I have been looking at different ideas and different
implementations to see what is possible to improve exec, and cleaning
the way exec interfaces with in kernel users. Only cleaning up the
interfaces of exec with rest of the kernel has managed to stabalize
and make it through review in time for v5.9-rc1 resulting in 2 sets of
changes this cycle.
- Implement kernel_execve
- Make the user mode driver code a better citizen
With kernel_execve the code size got a little larger as the copying of
parameters from userspace and copying of parameters from userspace is
now separate. The good news is kernel threads no longer need to play
games with set_fs to use exec. Which when combined with the rest of
Christophs set_fs changes should security bugs with set_fs much more
difficult"
* 'exec-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (23 commits)
exec: Implement kernel_execve
exec: Factor bprm_stack_limits out of prepare_arg_pages
exec: Factor bprm_execve out of do_execve_common
exec: Move bprm_mm_init into alloc_bprm
exec: Move initialization of bprm->filename into alloc_bprm
exec: Factor out alloc_bprm
exec: Remove unnecessary spaces from binfmts.h
umd: Stop using split_argv
umd: Remove exit_umh
bpfilter: Take advantage of the facilities of struct pid
exit: Factor thread_group_exited out of pidfd_poll
umd: Track user space drivers with struct pid
bpfilter: Move bpfilter_umh back into init data
exec: Remove do_execve_file
umh: Stop calling do_execve_file
umd: Transform fork_usermode_blob into fork_usermode_driver
umd: Rename umd_info.cmdline umd_info.driver_name
umd: For clarity rename umh_info umd_info
umh: Separate the user mode driver and the user mode helper support
umh: Remove call_usermodehelper_setup_file.
...
- Improve uclamp performance by using a static key for the fast path
- Add the "sched_util_clamp_min_rt_default" sysctl, to optimize for
better power efficiency of RT tasks on battery powered devices.
(The default is to maximize performance & reduce RT latencies.)
- Improve utime and stime tracking accuracy, which had a fixed boundary
of error, which created larger and larger relative errors as the values
become larger. This is now replaced with more precise arithmetics,
using the new mul_u64_u64_div_u64() helper in math64.h.
- Improve the deadline scheduler, such as making it capacity aware
- Improve frequency-invariant scheduling
- Misc cleanups in energy/power aware scheduling
- Add sched_update_nr_running tracepoint to track changes to nr_running
- Documentation additions and updates
- Misc cleanups and smaller fixes
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=PbO7
-----END PGP SIGNATURE-----
Merge tag 'sched-core-2020-08-03' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler updates from Ingo Molnar:
- Improve uclamp performance by using a static key for the fast path
- Add the "sched_util_clamp_min_rt_default" sysctl, to optimize for
better power efficiency of RT tasks on battery powered devices.
(The default is to maximize performance & reduce RT latencies.)
- Improve utime and stime tracking accuracy, which had a fixed boundary
of error, which created larger and larger relative errors as the
values become larger. This is now replaced with more precise
arithmetics, using the new mul_u64_u64_div_u64() helper in math64.h.
- Improve the deadline scheduler, such as making it capacity aware
- Improve frequency-invariant scheduling
- Misc cleanups in energy/power aware scheduling
- Add sched_update_nr_running tracepoint to track changes to nr_running
- Documentation additions and updates
- Misc cleanups and smaller fixes
* tag 'sched-core-2020-08-03' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (54 commits)
sched/doc: Factorize bits between sched-energy.rst & sched-capacity.rst
sched/doc: Document capacity aware scheduling
sched: Document arch_scale_*_capacity()
arm, arm64: Fix selection of CONFIG_SCHED_THERMAL_PRESSURE
Documentation/sysctl: Document uclamp sysctl knobs
sched/uclamp: Add a new sysctl to control RT default boost value
sched/uclamp: Fix a deadlock when enabling uclamp static key
sched: Remove duplicated tick_nohz_full_enabled() check
sched: Fix a typo in a comment
sched/uclamp: Remove unnecessary mutex_init()
arm, arm64: Select CONFIG_SCHED_THERMAL_PRESSURE
sched: Cleanup SCHED_THERMAL_PRESSURE kconfig entry
arch_topology, sched/core: Cleanup thermal pressure definition
trace/events/sched.h: fix duplicated word
linux/sched/mm.h: drop duplicated words in comments
smp: Fix a potential usage of stale nr_cpus
sched/fair: update_pick_idlest() Select group with lowest group_util when idle_cpus are equal
sched: nohz: stop passing around unused "ticks" parameter.
sched: Better document ttwu()
sched: Add a tracepoint to track rq->nr_running
...
Rather that hide their purpose in some dark, damp corner of Documentation/,
add some documentation to the default implementations.
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20200731192016.7484-2-valentin.schneider@arm.com
RT tasks by default run at the highest capacity/performance level. When
uclamp is selected this default behavior is retained by enforcing the
requested uclamp.min (p->uclamp_req[UCLAMP_MIN]) of the RT tasks to be
uclamp_none(UCLAMP_MAX), which is SCHED_CAPACITY_SCALE; the maximum
value.
This is also referred to as 'the default boost value of RT tasks'.
See commit 1a00d99997 ("sched/uclamp: Set default clamps for RT tasks").
On battery powered devices, it is desired to control this default
(currently hardcoded) behavior at runtime to reduce energy consumed by
RT tasks.
For example, a mobile device manufacturer where big.LITTLE architecture
is dominant, the performance of the little cores varies across SoCs, and
on high end ones the big cores could be too power hungry.
Given the diversity of SoCs, the new knob allows manufactures to tune
the best performance/power for RT tasks for the particular hardware they
run on.
They could opt to further tune the value when the user selects
a different power saving mode or when the device is actively charging.
The runtime aspect of it further helps in creating a single kernel image
that can be run on multiple devices that require different tuning.
Keep in mind that a lot of RT tasks in the system are created by the
kernel. On Android for instance I can see over 50 RT tasks, only
a handful of which created by the Android framework.
To control the default behavior globally by system admins and device
integrator, introduce the new sysctl_sched_uclamp_util_min_rt_default
to change the default boost value of the RT tasks.
I anticipate this to be mostly in the form of modifying the init script
of a particular device.
To avoid polluting the fast path with unnecessary code, the approach
taken is to synchronously do the update by traversing all the existing
tasks in the system. This could race with a concurrent fork(), which is
dealt with by introducing sched_post_fork() function which will ensure
the racy fork will get the right update applied.
Tested on Juno-r2 in combination with the RT capacity awareness [1].
By default an RT task will go to the highest capacity CPU and run at the
maximum frequency, which is particularly energy inefficient on high end
mobile devices because the biggest core[s] are 'huge' and power hungry.
With this patch the RT task can be controlled to run anywhere by
default, and doesn't cause the frequency to be maximum all the time.
Yet any task that really needs to be boosted can easily escape this
default behavior by modifying its requested uclamp.min value
(p->uclamp_req[UCLAMP_MIN]) via sched_setattr() syscall.
[1] 804d402fb6f6: ("sched/rt: Make RT capacity-aware")
Signed-off-by: Qais Yousef <qais.yousef@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20200716110347.19553-2-qais.yousef@arm.com
put_task_struct_many() is as put_task_struct() but puts several
references at once. Useful to batching it.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The following commit:
14533a16c4 ("thermal/cpu-cooling, sched/core: Move the arch_set_thermal_pressure() API to generic scheduler code")
moved the definition of arch_set_thermal_pressure() to sched/core.c, but
kept its declaration in linux/arch_topology.h. When building e.g. an x86
kernel with CONFIG_SCHED_THERMAL_PRESSURE=y, cpufreq_cooling.c ends up
getting the declaration of arch_set_thermal_pressure() from
include/linux/arch_topology.h, which is somewhat awkward.
On top of this, sched/core.c unconditionally defines
o The thermal_pressure percpu variable
o arch_set_thermal_pressure()
while arch_scale_thermal_pressure() does nothing unless redefined by the
architecture.
arch_*() functions are meant to be defined by architectures, so revert the
aforementioned commit and re-implement it in a way that keeps
arch_set_thermal_pressure() architecture-definable, and doesn't define the
thermal pressure percpu variable for kernels that don't need
it (CONFIG_SCHED_THERMAL_PRESSURE=n).
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20200712165917.9168-2-valentin.schneider@arm.com
The "ticks" parameter was added in commit 0f004f5a69 ("sched: Cure more
NO_HZ load average woes") since calc_global_nohz() was called and needed
the "ticks" argument.
But in commit c308b56b53 ("sched: Fix nohz load accounting -- again!")
it became unused as the function calc_global_nohz() dropped using "ticks".
Fixes: c308b56b53 ("sched: Fix nohz load accounting -- again!")
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/1593628458-32290-1-git-send-email-paul.gortmaker@windriver.com
Create an independent helper thread_group_exited which returns true
when all threads have passed exit_notify in do_exit. AKA all of the
threads are at least zombies and might be dead or completely gone.
Create this helper by taking the logic out of pidfd_poll where it is
already tested, and adding a READ_ONCE on the read of
task->exit_state.
I will be changing the user mode driver code to use this same logic
to know when a user mode driver needs to be restarted.
Place the new helper thread_group_exited in kernel/exit.c and
EXPORT it so it can be used by modules.
Link: https://lkml.kernel.org/r/20200702164140.4468-13-ebiederm@xmission.com
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Now that HAVE_COPY_THREAD_TLS has been removed, rename copy_thread_tls()
back simply copy_thread(). It's a simpler name, and doesn't imply that only
tls is copied here. This finishes an outstanding chunk of internal process
creation work since we've added clone3().
Cc: linux-arch@vger.kernel.org
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>A
Acked-by: Stafford Horne <shorne@gmail.com>
Acked-by: Greentime Hu <green.hu@gmail.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>A
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
All architectures support copy_thread_tls() now, so remove the legacy
copy_thread() function and the HAVE_COPY_THREAD_TLS config option. Everyone
uses the same process creation calling convention based on
copy_thread_tls() and struct kernel_clone_args. This will make it easier to
maintain the core process creation code under kernel/, simplifies the
callpaths and makes the identical for all architectures.
Cc: linux-arch@vger.kernel.org
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Acked-by: Greentime Hu <green.hu@gmail.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Now that all architectures have been switched to use _do_fork() and the new
struct kernel_clone_args calling convention we can remove the legacy
do_fork() helper completely. The calling convention used to be brittle and
do_fork() didn't buy us anything. The only calling convention accepted
should be based on struct kernel_clone_args going forward. It's cleaner and
uniform.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: "Peter Zijlstra (Intel)" <peterz@infradead.org>
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
So that the target task will exit the wait_event_interruptible-like
loop and call task_work_run() asap.
The patch turns "bool notify" into 0,TWA_RESUME,TWA_SIGNAL enum, the
new TWA_SIGNAL flag implies signal_wake_up(). However, it needs to
avoid the race with recalc_sigpending(), so the patch also adds the
new JOBCTL_TASK_WORK bit included in JOBCTL_PENDING_MASK.
TODO: once this patch is merged we need to change all current users
of task_work_add(notify = true) to use TWA_RESUME.
Cc: stable@vger.kernel.org # v5.7
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit
bf2c59fce4 ("sched/core: Fix illegal RCU from offline CPUs")
introduced a definition for mmdrop() but a a few lines above there is
already mmdrop() defined as static inline.
Remove the newly introduced mmdrop() definition.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20200618190810.790211-1-bigeasy@linutronix.de
This separate helper only existed to guarantee the mutual exclusivity of
CLONE_PIDFD and CLONE_PARENT_SETTID for legacy clone since CLONE_PIDFD
abuses the parent_tid field to return the pidfd. But we can actually handle
this uniformely thus removing the helper. For legacy clone we can detect
that CLONE_PIDFD is specified in conjunction with CLONE_PARENT_SETTID
because they will share the same memory which is invalid and for clone3()
setting the separate pidfd and parent_tid fields to the same memory is
bogus as well. So fold that helper directly into _do_fork() by detecting
this case.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: "Peter Zijlstra (Intel)" <peterz@infradead.org>
Cc: linux-m68k@lists.linux-m68k.org
Cc: x86@kernel.org
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
This is a kernel enhancement that configures the cpu affinity of kernel
threads via kernel boot option nohz_full=.
When this option is specified, the cpumask is immediately applied upon
kthread launch. This does not affect kernel threads that specify cpu
and node.
This allows CPU isolation (that is not allowing certain threads
to execute on certain CPUs) without using the isolcpus=domain parameter,
making it possible to enable load balancing on such CPUs
during runtime (see kernel-parameters.txt).
Note-1: this is based off on Wind River's patch at
https://github.com/starlingx-staging/stx-integ/blob/master/kernel/kernel-std/centos/patches/affine-compute-kernel-threads.patch
Difference being that this patch is limited to modifying kernel thread
cpumask. Behaviour of other threads can be controlled via cgroups or
sched_setaffinity.
Note-2: Wind River's patch was based off Christoph Lameter's patch at
https://lwn.net/Articles/565932/ with the only difference being
the kernel parameter changed from kthread to kthread_cpus.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20200527142909.23372-3-frederic@kernel.org
Now the last users of show_stack() got converted to use an explicit log
level, show_stack_loglvl() can drop it's redundant suffix and become once
again well known show_stack().
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/20200418201944.482088-51-dima@arista.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Show the stack trace on a CPU with the same log level as "CPU%d" header.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Link: http://lkml.kernel.org/r/20200418201944.482088-45-dima@arista.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 401c636a0e ("kernel/hung_task.c: show all hung tasks before
panic") introduced a change in that we started to show all CPUs
backtraces when a hung task is detected _and_ the sysctl/kernel
parameter "hung_task_panic" is set. The idea is good, because usually
when observing deadlocks (that may lead to hung tasks), the culprit is
another task holding a lock and not necessarily the task detected as
hung.
The problem with this approach is that dumping backtraces is a slightly
expensive task, specially printing that on console (and specially in
many CPU machines, as servers commonly found nowadays). So, users that
plan to collect a kdump to investigate the hung tasks and narrow down
the deadlock definitely don't need the CPUs backtrace on dmesg/console,
which will delay the panic and pollute the log (crash tool would easily
grab all CPUs traces with 'bt -a' command).
Also, there's the reciprocal scenario: some users may be interested in
seeing the CPUs backtraces but not have the system panic when a hung
task is detected. The current approach hence is almost as embedding a
policy in the kernel, by forcing the CPUs backtraces' dump (only) on
hung_task_panic.
This patch decouples the panic event on hung task from the CPUs
backtraces dump, by creating (and documenting) a new sysctl called
"hung_task_all_cpu_backtrace", analog to the approach taken on soft/hard
lockups, that have both a panic and an "all_cpu_backtrace" sysctl to
allow individual control. The new mechanism for dumping the CPUs
backtraces on hung task detection respects "hung_task_warnings" by not
dumping the traces in case there's no warnings left.
Signed-off-by: Guilherme G. Piccoli <gpiccoli@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Link: http://lkml.kernel.org/r/20200327223646.20779-1-gpiccoli@canonical.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull proc updates from Eric Biederman:
"This has four sets of changes:
- modernize proc to support multiple private instances
- ensure we see the exit of each process tid exactly
- remove has_group_leader_pid
- use pids not tasks in posix-cpu-timers lookup
Alexey updated proc so each mount of proc uses a new superblock. This
allows people to actually use mount options with proc with no fear of
messing up another mount of proc. Given the kernel's internal mounts
of proc for things like uml this was a real problem, and resulted in
Android's hidepid mount options being ignored and introducing security
issues.
The rest of the changes are small cleanups and fixes that came out of
my work to allow this change to proc. In essence it is swapping the
pids in de_thread during exec which removes a special case the code
had to handle. Then updating the code to stop handling that special
case"
* 'proc-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
proc: proc_pid_ns takes super_block as an argument
remove the no longer needed pid_alive() check in __task_pid_nr_ns()
posix-cpu-timers: Replace __get_task_for_clock with pid_for_clock
posix-cpu-timers: Replace cpu_timer_pid_type with clock_pid_type
posix-cpu-timers: Extend rcu_read_lock removing task_struct references
signal: Remove has_group_leader_pid
exec: Remove BUG_ON(has_group_leader_pid)
posix-cpu-timer: Unify the now redundant code in lookup_task
posix-cpu-timer: Tidy up group_leader logic in lookup_task
proc: Ensure we see the exit of each process tid exactly once
rculist: Add hlists_swap_heads_rcu
proc: Use PIDTYPE_TGID in next_tgid
Use proc_pid_ns() to get pid_namespace from the proc superblock
proc: use named enums for better readability
proc: use human-readable values for hidepid
docs: proc: add documentation for "hidepid=4" and "subset=pid" options and new mount behavior
proc: add option to mount only a pids subset
proc: instantiate only pids that we can ptrace on 'hidepid=4' mount option
proc: allow to mount many instances of proc in one pid namespace
proc: rename struct proc_fs_info to proc_fs_opts
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
In the CPU-offline process, it calls mmdrop() after idle entry and the
subsequent call to cpuhp_report_idle_dead(). Once execution passes the
call to rcu_report_dead(), RCU is ignoring the CPU, which results in
lockdep complaining when mmdrop() uses RCU from either memcg or
debugobjects below.
Fix it by cleaning up the active_mm state from BP instead. Every arch
which has CONFIG_HOTPLUG_CPU should have already called idle_task_exit()
from AP. The only exception is parisc because it switches them to
&init_mm unconditionally (see smp_boot_one_cpu() and smp_cpu_init()),
but the patch will still work there because it calls mmgrab(&init_mm) in
smp_cpu_init() and then should call mmdrop(&init_mm) in finish_cpu().
WARNING: suspicious RCU usage
-----------------------------
kernel/workqueue.c:710 RCU or wq_pool_mutex should be held!
other info that might help us debug this:
RCU used illegally from offline CPU!
Call Trace:
dump_stack+0xf4/0x164 (unreliable)
lockdep_rcu_suspicious+0x140/0x164
get_work_pool+0x110/0x150
__queue_work+0x1bc/0xca0
queue_work_on+0x114/0x120
css_release+0x9c/0xc0
percpu_ref_put_many+0x204/0x230
free_pcp_prepare+0x264/0x570
free_unref_page+0x38/0xf0
__mmdrop+0x21c/0x2c0
idle_task_exit+0x170/0x1b0
pnv_smp_cpu_kill_self+0x38/0x2e0
cpu_die+0x48/0x64
arch_cpu_idle_dead+0x30/0x50
do_idle+0x2f4/0x470
cpu_startup_entry+0x38/0x40
start_secondary+0x7a8/0xa80
start_secondary_resume+0x10/0x14
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Qian Cai <cai@lca.pw>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Link: https://lkml.kernel.org/r/20200401214033.8448-1-cai@lca.pw
That flag is set unconditionally in sd_init(), and no one checks for it
anymore. Remove it.
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20200415210512.805-5-valentin.schneider@arm.com
After the introduction of exchange_tids has_group_leader_pid is
equivalent to thread_group_leader. After the last couple of cleanups
has_group_leader_pid has no more callers.
So remove the now unused and redundant has_group_leader_pid.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Pull in Christoph Hellwig's series that changes the sysctl's ->proc_handler
methods to take kernel pointers instead. It gets rid of the set_fs address
space overrides used by BPF. As per discussion, pull in the feature branch
into bpf-next as it relates to BPF sysctl progs.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200427071508.GV23230@ZenIV.linux.org.uk/T/
Instead of having all the sysctl handlers deal with user pointers, which
is rather hairy in terms of the BPF interaction, copy the input to and
from userspace in common code. This also means that the strings are
always NUL-terminated by the common code, making the API a little bit
safer.
As most handler just pass through the data to one of the common handlers
a lot of the changes are mechnical.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Pull cgroup updates from Tejun Heo:
- Christian extended clone3 so that processes can be spawned into
cgroups directly.
This is not only neat in terms of semantics but also avoids grabbing
the global cgroup_threadgroup_rwsem for migration.
- Daniel added !root xattr support to cgroupfs.
Userland already uses xattrs on cgroupfs for bookkeeping. This will
allow delegated cgroups to support such usages.
- Prateek tried to make cpuset hotplug handling synchronous but that
led to possible deadlock scenarios. Reverted.
- Other minor changes including release_agent_path handling cleanup.
* 'for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
docs: cgroup-v1: Document the cpuset_v2_mode mount option
Revert "cpuset: Make cpuset hotplug synchronous"
cgroupfs: Support user xattrs
kernfs: Add option to enable user xattrs
kernfs: Add removed_size out param for simple_xattr_set
kernfs: kvmalloc xattr value instead of kmalloc
cgroup: Restructure release_agent_path handling
selftests/cgroup: add tests for cloning into cgroups
clone3: allow spawning processes into cgroups
cgroup: add cgroup_may_write() helper
cgroup: refactor fork helpers
cgroup: add cgroup_get_from_file() helper
cgroup: unify attach permission checking
cpuset: Make cpuset hotplug synchronous
cgroup.c: Use built-in RCU list checking
kselftest/cgroup: add cgroup destruction test
cgroup: Clean up css_set task traversal
Merge updates from Andrew Morton:
"A large amount of MM, plenty more to come.
Subsystems affected by this patch series:
- tools
- kthread
- kbuild
- scripts
- ocfs2
- vfs
- mm: slub, kmemleak, pagecache, gup, swap, memcg, pagemap, mremap,
sparsemem, kasan, pagealloc, vmscan, compaction, mempolicy,
hugetlbfs, hugetlb"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (155 commits)
include/linux/huge_mm.h: check PageTail in hpage_nr_pages even when !THP
mm/hugetlb: fix build failure with HUGETLB_PAGE but not HUGEBTLBFS
selftests/vm: fix map_hugetlb length used for testing read and write
mm/hugetlb: remove unnecessary memory fetch in PageHeadHuge()
mm/hugetlb.c: clean code by removing unnecessary initialization
hugetlb_cgroup: add hugetlb_cgroup reservation docs
hugetlb_cgroup: add hugetlb_cgroup reservation tests
hugetlb: support file_region coalescing again
hugetlb_cgroup: support noreserve mappings
hugetlb_cgroup: add accounting for shared mappings
hugetlb: disable region_add file_region coalescing
hugetlb_cgroup: add reservation accounting for private mappings
mm/hugetlb_cgroup: fix hugetlb_cgroup migration
hugetlb_cgroup: add interface for charge/uncharge hugetlb reservations
hugetlb_cgroup: add hugetlb_cgroup reservation counter
hugetlbfs: Use i_mmap_rwsem to address page fault/truncate race
hugetlbfs: use i_mmap_rwsem for more pmd sharing synchronization
mm/memblock.c: remove redundant assignment to variable max_addr
mm: mempolicy: require at least one nodeid for MPOL_PREFERRED
mm: mempolicy: use VM_BUG_ON_VMA in queue_pages_test_walk()
...
Pull exec/proc updates from Eric Biederman:
"This contains two significant pieces of work: the work to sort out
proc_flush_task, and the work to solve a deadlock between strace and
exec.
Fixing proc_flush_task so that it no longer requires a persistent
mount makes improvements to proc possible. The removal of the
persistent mount solves an old regression that that caused the hidepid
mount option to only work on remount not on mount. The regression was
found and reported by the Android folks. This further allows Alexey
Gladkov's work making proc mount options specific to an individual
mount of proc to move forward.
The work on exec starts solving a long standing issue with exec that
it takes mutexes of blocking userspace applications, which makes exec
extremely deadlock prone. For the moment this adds a second mutex with
a narrower scope that handles all of the easy cases. Which makes the
tricky cases easy to spot. With a little luck the code to solve those
deadlocks will be ready by next merge window"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (25 commits)
signal: Extend exec_id to 64bits
pidfd: Use new infrastructure to fix deadlocks in execve
perf: Use new infrastructure to fix deadlocks in execve
proc: io_accounting: Use new infrastructure to fix deadlocks in execve
proc: Use new infrastructure to fix deadlocks in execve
kernel/kcmp.c: Use new infrastructure to fix deadlocks in execve
kernel: doc: remove outdated comment cred.c
mm: docs: Fix a comment in process_vm_rw_core
selftests/ptrace: add test cases for dead-locks
exec: Fix a deadlock in strace
exec: Add exec_update_mutex to replace cred_guard_mutex
exec: Move exec_mmap right after de_thread in flush_old_exec
exec: Move cleanup of posix timers on exec out of de_thread
exec: Factor unshare_sighand out of de_thread and call it separately
exec: Only compute current once in flush_old_exec
pid: Improve the comment about waiting in zap_pid_ns_processes
proc: Remove the now unnecessary internal mount of proc
uml: Create a private mount of proc for mconsole
uml: Don't consult current to find the proc_mnt in mconsole_proc
proc: Use a list of inodes to flush from proc
...
The idea comes from the upstream discussion between Linus and Andrea:
https://lore.kernel.org/lkml/20171102193644.GB22686@redhat.com/
A summary to the issue: there was a special path in handle_userfault() in
the past that we'll return a VM_FAULT_NOPAGE when we detected non-fatal
signals when waiting for userfault handling. We did that by reacquiring
the mmap_sem before returning. However that brings a risk in that the
vmas might have changed when we retake the mmap_sem and even we could be
holding an invalid vma structure.
This patch is a preparation of removing that special path by allowing the
page fault to return even faster if we were interrupted by a non-fatal
signal during a user-mode page fault handling routine.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Suggested-by: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Tested-by: Brian Geffon <bgeffon@google.com>
Cc: Bobby Powers <bobbypowers@gmail.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Denis Plotnikov <dplotnikov@virtuozzo.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: "Kirill A . Shutemov" <kirill@shutemov.name>
Cc: Martin Cracauer <cracauer@cons.org>
Cc: Marty McFadden <mcfadden8@llnl.gov>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Maya Gokhale <gokhale2@llnl.gov>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Link: http://lkml.kernel.org/r/20200220160230.9598-1-peterx@redhat.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For most architectures, we've got a quick path to detect fatal signal
after a handle_mm_fault(). Introduce a helper for that quick path.
It cleans the current codes a bit so we don't need to duplicate the same
check across archs. More importantly, this will be an unified place that
we handle the signal immediately right after an interrupted page fault, so
it'll be much easier for us if we want to change the behavior of handling
signals later on for all the archs.
Note that currently only part of the archs are using this new helper,
because some archs have their own way to handle signals. In the follow up
patches, we'll try to apply this helper to all the rest of archs.
Another note is that the "regs" parameter in the new helper is not used
yet. It'll be used very soon. Now we kept it in this patch only to avoid
touching all the archs again in the follow up patches.
[peterx@redhat.com: fix sparse warnings]
Link: http://lkml.kernel.org/r/20200311145921.GD479302@xz-x1
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Tested-by: Brian Geffon <bgeffon@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Bobby Powers <bobbypowers@gmail.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Denis Plotnikov <dplotnikov@virtuozzo.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: "Kirill A . Shutemov" <kirill@shutemov.name>
Cc: Martin Cracauer <cracauer@cons.org>
Cc: Marty McFadden <mcfadden8@llnl.gov>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Maya Gokhale <gokhale2@llnl.gov>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Link: http://lkml.kernel.org/r/20200220155353.8676-4-peterx@redhat.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The cred_guard_mutex is problematic as it is held over possibly
indefinite waits for userspace. The possible indefinite waits for
userspace that I have identified are: The cred_guard_mutex is held in
PTRACE_EVENT_EXIT waiting for the tracer. The cred_guard_mutex is
held over "put_user(0, tsk->clear_child_tid)" in exit_mm(). The
cred_guard_mutex is held over "get_user(futex_offset, ...") in
exit_robust_list. The cred_guard_mutex held over copy_strings.
The functions get_user and put_user can trigger a page fault which can
potentially wait indefinitely in the case of userfaultfd or if
userspace implements part of the page fault path.
In any of those cases the userspace process that the kernel is waiting
for might make a different system call that winds up taking the
cred_guard_mutex and result in deadlock.
Holding a mutex over any of those possibly indefinite waits for
userspace does not appear necessary. Add exec_update_mutex that will
just cover updating the process during exec where the permissions and
the objects pointed to by the task struct may be out of sync.
The plan is to switch the users of cred_guard_mutex to
exec_update_mutex one by one. This lets us move forward while still
being careful and not introducing any regressions.
Link: https://lore.kernel.org/lkml/20160921152946.GA24210@dhcp22.suse.cz/
Link: https://lore.kernel.org/lkml/AM6PR03MB5170B06F3A2B75EFB98D071AE4E60@AM6PR03MB5170.eurprd03.prod.outlook.com/
Link: https://lore.kernel.org/linux-fsdevel/20161102181806.GB1112@redhat.com/
Link: https://lore.kernel.org/lkml/20160923095031.GA14923@redhat.com/
Link: https://lore.kernel.org/lkml/20170213141452.GA30203@redhat.com/
Ref: 45c1a159b85b ("Add PTRACE_O_TRACEVFORKDONE and PTRACE_O_TRACEEXIT facilities.")
Ref: 456f17cd1a28 ("[PATCH] user-vm-unlock-2.5.31-A2")
Reviewed-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Introduce the arch_scale_thermal_pressure() callback to retrieve per CPU thermal
pressure.
Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/20200222005213.3873-3-thara.gopinath@linaro.org
Pull scheduler fixes from Ingo Molnar:
"Misc fixes all over the place:
- Fix NUMA over-balancing between lightly loaded nodes. This is
fallout of the big load-balancer rewrite.
- Fix the NOHZ remote loadavg update logic, which fixes anomalies
like reported 150 loadavg on mostly idle CPUs.
- Fix XFS performance/scalability
- Fix throttled groups unbound task-execution bug
- Fix PSI procfs boundary condition
- Fix the cpu.uclamp.{min,max} cgroup configuration write checks
- Fix DocBook annotations
- Fix RCU annotations
- Fix overly CPU-intensive housekeeper CPU logic loop on large CPU
counts"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Fix kernel-doc warning in attach_entity_load_avg()
sched/core: Annotate curr pointer in rq with __rcu
sched/psi: Fix OOB write when writing 0 bytes to PSI files
sched/fair: Allow a per-CPU kthread waking a task to stack on the same CPU, to fix XFS performance regression
sched/fair: Prevent unlimited runtime on throttled group
sched/nohz: Optimize get_nohz_timer_target()
sched/uclamp: Reject negative values in cpu_uclamp_write()
sched/fair: Allow a small load imbalance between low utilisation SD_NUMA domains
timers/nohz: Update NOHZ load in remote tick
sched/core: Don't skip remote tick for idle CPUs
This adds support for creating a process in a different cgroup than its
parent. Callers can limit and account processes and threads right from
the moment they are spawned:
- A service manager can directly spawn new services into dedicated
cgroups.
- A process can be directly created in a frozen cgroup and will be
frozen as well.
- The initial accounting jitter experienced by process supervisors and
daemons is eliminated with this.
- Threaded applications or even thread implementations can choose to
create a specific cgroup layout where each thread is spawned
directly into a dedicated cgroup.
This feature is limited to the unified hierarchy. Callers need to pass
a directory file descriptor for the target cgroup. The caller can
choose to pass an O_PATH file descriptor. All usual migration
restrictions apply, i.e. there can be no processes in inner nodes. In
general, creating a process directly in a target cgroup adheres to all
migration restrictions.
One of the biggest advantages of this feature is that CLONE_INTO_GROUP does
not need to grab the write side of the cgroup cgroup_threadgroup_rwsem.
This global lock makes moving tasks/threads around super expensive. With
clone3() this lock is avoided.
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Li Zefan <lizefan@huawei.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: cgroups@vger.kernel.org
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The way loadavg is tracked during nohz only pays attention to the load
upon entering nohz. This can be particularly noticeable if full nohz is
entered while non-idle, and then the cpu goes idle and stays that way for
a long time.
Use the remote tick to ensure that full nohz cpus report their deltas
within a reasonable time.
[ swood: Added changelog and removed recheck of stopped tick. ]
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Scott Wood <swood@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/1578736419-14628-3-git-send-email-swood@redhat.com
Pull scheduler updates from Ingo Molnar:
"These were the main changes in this cycle:
- More -rt motivated separation of CONFIG_PREEMPT and
CONFIG_PREEMPTION.
- Add more low level scheduling topology sanity checks and warnings
to filter out nonsensical topologies that break scheduling.
- Extend uclamp constraints to influence wakeup CPU placement
- Make the RT scheduler more aware of asymmetric topologies and CPU
capacities, via uclamp metrics, if CONFIG_UCLAMP_TASK=y
- Make idle CPU selection more consistent
- Various fixes, smaller cleanups, updates and enhancements - please
see the git log for details"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (58 commits)
sched/fair: Define sched_idle_cpu() only for SMP configurations
sched/topology: Assert non-NUMA topology masks don't (partially) overlap
idle: fix spelling mistake "iterrupts" -> "interrupts"
sched/fair: Remove redundant call to cpufreq_update_util()
sched/psi: create /proc/pressure and /proc/pressure/{io|memory|cpu} only when psi enabled
sched/fair: Fix sgc->{min,max}_capacity calculation for SD_OVERLAP
sched/fair: calculate delta runnable load only when it's needed
sched/cputime: move rq parameter in irqtime_account_process_tick
stop_machine: Make stop_cpus() static
sched/debug: Reset watchdog on all CPUs while processing sysrq-t
sched/core: Fix size of rq::uclamp initialization
sched/uclamp: Fix a bug in propagating uclamp value in new cgroups
sched/fair: Load balance aggressively for SCHED_IDLE CPUs
sched/fair : Improve update_sd_pick_busiest for spare capacity case
watchdog: Remove soft_lockup_hrtimer_cnt and related code
sched/rt: Make RT capacity-aware
sched/fair: Make EAS wakeup placement consider uclamp restrictions
sched/fair: Make task_fits_capacity() consider uclamp restrictions
sched/uclamp: Rename uclamp_util_with() into uclamp_rq_util_with()
sched/uclamp: Make uclamp util helpers use and return UL values
...
The affinity of managed interrupts is completely handled in the kernel and
cannot be changed via the /proc/irq/* interfaces from user space. As the
kernel tries to spread out interrupts evenly accross CPUs on x86 to prevent
vector exhaustion, it can happen that a managed interrupt whose affinity
mask contains both isolated and housekeeping CPUs is routed to an isolated
CPU. As a consequence IO submitted on a housekeeping CPU causes interrupts
on the isolated CPU.
Add a new sub-parameter 'managed_irq' for 'isolcpus' and the corresponding
logic in the interrupt affinity selection code.
The subparameter indicates to the interrupt affinity selection logic that
it should try to avoid the above scenario.
This isolation is best effort and only effective if the automatically
assigned interrupt mask of a device queue contains isolated and
housekeeping CPUs. If housekeeping CPUs are online then such interrupts are
directed to the housekeeping CPU so that IO submitted on the housekeeping
CPU cannot disturb the isolated CPU.
If a queue's affinity mask contains only isolated CPUs then this parameter
has no effect on the interrupt routing decision, though interrupts are only
happening when tasks running on those isolated CPUs submit IO. IO submitted
on housekeeping CPUs has no influence on those queues.
If the affinity mask contains both housekeeping and isolated CPUs, but none
of the contained housekeeping CPUs is online, then the interrupt is also
routed to an isolated CPU. Interrupts are only delivered when one of the
isolated CPUs in the affinity mask submits IO. If one of the contained
housekeeping CPUs comes online, the CPU hotplug logic migrates the
interrupt automatically back to the upcoming housekeeping CPU. Depending on
the type of interrupt controller, this can require that at least one
interrupt is delivered to the isolated CPU in order to complete the
migration.
[ tglx: Removed unused parameter, added and edited comments/documentation
and rephrased the changelog so it contains more details. ]
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20200120091625.17912-1-ming.lei@redhat.com
With commit
bef69dd878 ("sched/cpufreq: Move the cfs_rq_util_change() call to cpufreq_update_util()")
update_load_avg() has become the central point for calling cpufreq
(not including the update of blocked load). This change helps to
simplify further the number of calls to cpufreq_update_util() and to
remove last redundant ones. With update_load_avg(), we are now sure
that cpufreq_update_util() will be called after every task attachment
to a cfs_rq and especially after propagating this event down to the
util_avg of the root cfs_rq, which is the level that is used by
cpufreq governors like schedutil to set the frequency of a CPU.
The SCHED_CPUFREQ_MIGRATION flag forces an early call to cpufreq when
the migration happens in a cgroup whereas util_avg of root cfs_rq is
not yet updated and this call is duplicated with the one that happens
immediately after when the migration event reaches the root cfs_rq.
The dedicated flag SCHED_CPUFREQ_MIGRATION is now useless and can be
removed. The interface of attach_entity_load_avg() can also be
simplified accordingly.
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lkml.kernel.org/r/1579083620-24943-1-git-send-email-vincent.guittot@linaro.org
The scheduler code calling cpufreq_update_util() may run during CPU
offline on the target CPU after the IRQ work lists have been flushed
for it, so the target CPU should be prevented from running code that
may queue up an IRQ work item on it at that point.
Unfortunately, that may not be the case if dvfs_possible_from_any_cpu
is set for at least one cpufreq policy in the system, because that
allows the CPU going offline to run the utilization update callback
of the cpufreq governor on behalf of another (online) CPU in some
cases.
If that happens, the cpufreq governor callback may queue up an IRQ
work on the CPU running it, which is going offline, and the IRQ work
may not be flushed after that point. Moreover, that IRQ work cannot
be flushed until the "offlining" CPU goes back online, so if any
other CPU calls irq_work_sync() to wait for the completion of that
IRQ work, it will have to wait until the "offlining" CPU is back
online and that may not happen forever. In particular, a system-wide
deadlock may occur during CPU online as a result of that.
The failing scenario is as follows. CPU0 is the boot CPU, so it
creates a cpufreq policy and becomes the "leader" of it
(policy->cpu). It cannot go offline, because it is the boot CPU.
Next, other CPUs join the cpufreq policy as they go online and they
leave it when they go offline. The last CPU to go offline, say CPU3,
may queue up an IRQ work while running the governor callback on
behalf of CPU0 after leaving the cpufreq policy because of the
dvfs_possible_from_any_cpu effect described above. Then, CPU0 is
the only online CPU in the system and the stale IRQ work is still
queued on CPU3. When, say, CPU1 goes back online, it will run
irq_work_sync() to wait for that IRQ work to complete and so it
will wait for CPU3 to go back online (which may never happen even
in principle), but (worse yet) CPU0 is waiting for CPU1 at that
point too and a system-wide deadlock occurs.
To address this problem notice that CPUs which cannot run cpufreq
utilization update code for themselves (for example, because they
have left the cpufreq policies that they belonged to), should also
be prevented from running that code on behalf of the other CPUs that
belong to a cpufreq policy with dvfs_possible_from_any_cpu set and so
in that case the cpufreq_update_util_data pointer of the CPU running
the code must not be NULL as well as for the CPU which is the target
of the cpufreq utilization update in progress.
Accordingly, change cpufreq_this_cpu_can_update() into a regular
function in kernel/sched/cpufreq.c (instead of a static inline in a
header file) and make it check the cpufreq_update_util_data pointer
of the local CPU if dvfs_possible_from_any_cpu is set for the target
cpufreq policy.
Also update the schedutil governor to do the
cpufreq_this_cpu_can_update() check in the non-fast-switch
case too to avoid the stale IRQ work issues.
Fixes: 99d14d0e16 ("cpufreq: Process remote callbacks from any CPU if the platform permits")
Link: https://lore.kernel.org/linux-pm/20191121093557.bycvdo4xyinbc5cb@vireshk-i7/
Reported-by: Anson Huang <anson.huang@nxp.com>
Tested-by: Anson Huang <anson.huang@nxp.com>
Cc: 4.14+ <stable@vger.kernel.org> # 4.14+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Peng Fan <peng.fan@nxp.com> (i.MX8QXP-MEK)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull locking updates from Ingo Molnar:
"The main changes in this cycle were:
- A comprehensive rewrite of the robust/PI futex code's exit handling
to fix various exit races. (Thomas Gleixner et al)
- Rework the generic REFCOUNT_FULL implementation using
atomic_fetch_* operations so that the performance impact of the
cmpxchg() loops is mitigated for common refcount operations.
With these performance improvements the generic implementation of
refcount_t should be good enough for everybody - and this got
confirmed by performance testing, so remove ARCH_HAS_REFCOUNT and
REFCOUNT_FULL entirely, leaving the generic implementation enabled
unconditionally. (Will Deacon)
- Other misc changes, fixes, cleanups"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
lkdtm: Remove references to CONFIG_REFCOUNT_FULL
locking/refcount: Remove unused 'refcount_error_report()' function
locking/refcount: Consolidate implementations of refcount_t
locking/refcount: Consolidate REFCOUNT_{MAX,SATURATED} definitions
locking/refcount: Move saturation warnings out of line
locking/refcount: Improve performance of generic REFCOUNT_FULL code
locking/refcount: Move the bulk of the REFCOUNT_FULL implementation into the <linux/refcount.h> header
locking/refcount: Remove unused refcount_*_checked() variants
locking/refcount: Ensure integer operands are treated as signed
locking/refcount: Define constants for saturation and max refcount values
futex: Prevent exit livelock
futex: Provide distinct return value when owner is exiting
futex: Add mutex around futex exit
futex: Provide state handling for exec() as well
futex: Sanitize exit state handling
futex: Mark the begin of futex exit explicitly
futex: Set task::futex_state to DEAD right after handling futex exit
futex: Split futex_mm_release() for exit/exec
exit/exec: Seperate mm_release()
futex: Replace PF_EXITPIDONE with a state
...
David Howells