Some PHYs can be linked with PSE (Power Sourcing Equipment), so search
for related nodes and attach it to the phydev.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rework error handling as preparation for PSE patch. This patch should
make it easier to extend this function.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some multigig SFPs from RollBall and Hilink do not expose functional
MDIO access to the internal PHY of the SFP via I2C address 0x56
(although there seems to be read-only clause 22 access on this address).
Instead these SFPs PHY can be accessed via I2C via the SFP Enhanced
Digital Diagnostic Interface - I2C address 0x51. The SFP_PAGE has to be
selected to 3 and the password must be filled with 0xff bytes for this
PHY communication to work.
This extends the mdio-i2c driver to support this protocol by adding a
special parameter to mdio_i2c_alloc function via which this RollBall
protocol can be selected.
Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_err() can be replace with dev_err_probe() which will check if error
code is -EPROBE_DEFER.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220915065043.665138-3-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
dev_err() can be replace with dev_err_probe() which will check if error
code is -EPROBE_DEFER.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220915065043.665138-2-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
dev_err() can be replace with dev_err_probe() which will check if error
code is -EPROBE_DEFER.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220915065043.665138-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In of_mdiobus_register(), we should call of_node_put() for 'child'
escaped out of for_each_available_child_of_node().
Fixes: 66bdede495 ("of_mdio: Fix broken PHY IRQ in case of probe deferral")
Co-developed-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220913125659.3331969-1-windhl@126.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=HdIo
-----END PGP SIGNATURE-----
Merge tag 'ib-mfd-net-pinctrl-v6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Lee Jones says:
====================
Immutable branch between MFD, Net and Pinctrl due for the v6.0 merge window
* tag 'ib-mfd-net-pinctrl-v6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: ocelot: Add support for the vsc7512 chip via spi
dt-bindings: mfd: ocelot: Add bindings for VSC7512
resource: add define macro for register address resources
pinctrl: microchip-sgpio: add ability to be used in a non-mmio configuration
pinctrl: microchip-sgpio: allow sgpio driver to be used as a module
pinctrl: ocelot: add ability to be used in a non-mmio configuration
net: mdio: mscc-miim: add ability to be used in a non-mmio configuration
mfd: ocelot: Add helper to get regmap from a resource
====================
Link: https://lore.kernel.org/r/YxrjyHcceLOFlT/c@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are a few Ocelot chips that contain the logic for this bus, but are
controlled externally. Specifically the VSC7511, 7512, 7513, and 7514. In
the externally controlled configurations these registers are not
memory-mapped.
Add support for these non-memory-mapped configurations.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20220905162132.2943088-3-colin.foster@in-advantage.com
This reverts commit f8217275b5.
There are a few more issues to fix that have been reported in the thread
for the original series [1]. We'll need to fix those before this will work.
So, revert it for now.
[1] - https://lore.kernel.org/lkml/CAMuHMdWo_wRwV-i_iyTxVnEsf3Th9GBAG+wxUQMQGnw1t2ijTg@mail.gmail.com/
Fixes: f8217275b5 ("net: mdio: Delete usage of driver_deferred_probe_check_state()")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20220819221616.2107893-3-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that fw_devlink=on by default and fw_devlink supports interrupt
properties, the execution will never get to the point where
driver_deferred_probe_check_state() is called before the supplier has
probed successfully or before deferred probe timeout has expired.
So, delete the call and replace it with -ENODEV.
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20220601070707.3946847-4-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Error values inside the probe function must be < 0. The ENOMEM return
value has the wrong sign: it is positive instead of negative.
Add a minus sign.
Fixes: e239756717 ("net: mdio: Add BCM6368 MDIO mux bus controller")
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220428211931.8130-1-dossche.niels@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add reset assertion/deassertion for Aspeed MDIO. There are 4 MDIO
controllers embedded in Aspeed AST2600 SOC and share one reset control
register SCU50[3]. To work with old DT blobs which don't have the reset
property, devm_reset_control_get_optional_shared is used in this change.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Create a local device *dev in order to not dereference the platform_device
several times throughout the probe function.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a driver for an interrupt controller is missing, of_irq_get()
returns -EPROBE_DEFER ad infinitum, causing
fwnode_mdiobus_phy_device_register(), and ultimately, the entire
of_mdiobus_register() call, to fail. In turn, any phy_connect() call
towards a PHY on this MDIO bus will also fail.
This is not what is expected to happen, because the PHY library falls
back to poll mode when of_irq_get() returns a hard error code, and the
MDIO bus, PHY and attached Ethernet controller work fine, albeit
suboptimally, when the PHY library polls for link status. However,
-EPROBE_DEFER has special handling given the assumption that at some
point probe deferral will stop, and the driver for the supplier will
kick in and create the IRQ domain.
Reasons for which the interrupt controller may be missing:
- It is not yet written. This may happen if a more recent DT blob (with
an interrupt-parent for the PHY) is used to boot an old kernel where
the driver didn't exist, and that kernel worked with the
vintage-correct DT blob using poll mode.
- It is compiled out. Behavior is the same as above.
- It is compiled as a module. The kernel will wait for a number of
seconds specified in the "deferred_probe_timeout" boot parameter for
user space to load the required module. The current default is 0,
which times out at the end of initcalls. It is possible that this
might cause regressions unless users adjust this boot parameter.
The proposed solution is to use the driver_deferred_probe_check_state()
helper function provided by the driver core, which gives up after some
-EPROBE_DEFER attempts, taking "deferred_probe_timeout" into consideration.
The return code is changed from -EPROBE_DEFER into -ENODEV or
-ETIMEDOUT, depending on whether the kernel is compiled with support for
modules or not.
Fixes: 66bdede495 ("of_mdio: Fix broken PHY IRQ in case of probe deferral")
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220407165538.4084809-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add Clause 45 support for Aspeed mdio driver.
Signed-off-by: Potin Lai <potin.lai@quantatw.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add following additional functions to move out the implementation from
aspeed_mdio_read() and aspeed_mdio_write().
c22:
- aspeed_mdio_read_c22()
- aspeed_mdio_write_c22()
c45:
- aspeed_mdio_read_c45()
- aspeed_mdio_write_c45()
Signed-off-by: Potin Lai <potin.lai@quantatw.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add aspeed_mdio_op() and aseed_mdio_get_data() for register accessing.
aspeed_mdio_op() handles operations, write command to control register,
then check and wait operations is finished (bit 31 is cleared).
aseed_mdio_get_data() fetchs the result value of operation from data
register.
Signed-off-by: Potin Lai <potin.lai@quantatw.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, the MDIO bus will have the hardware default bus frequency.
Read the desired frequency of the bus from the device tree and configure
it.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver doesn't support clause 45 register access yet, but doesn't
check if the access is a c45 one either. This leads to spurious register
reads and writes. Add the check.
Fixes: 542671fe4d ("net: phy: mscc-miim: Add MDIO driver")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LAN966x has two internal PHYs which are in reset by default. The
driver already supported the internal PHYs of the SparX-5. Now add
support for the LAN966x, too. Add a new compatible to distinguish them.
The LAN966x has additional control bits in this register, thus convert
the regmap_write() to regmap_update_bits() to leave the remaining bits
untouched. This doesn't change anything for the SparX-5 SoC, because
there, the register consists only of reset bits.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace the magic numbers by macros which are already defined. It seems
the original commit missed to use them.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This driver can have up to two regmaps. If the second one is registered
its debugfs entry will have the same name as the first one and the
following error will be printed:
[ 3.833521] debugfs: Directory 'e200413c.mdio' with parent 'regmap' already present!
Give the second regmap a name to avoid this.
Fixes: a27a762828 ("net: mdio: mscc-miim: convert to a regmap implementation")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220312224140.4173930-1-michael@walle.cc
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In case of DT-configured systems it may be hard to identify the PHY
interrupt in the /proc/interrupts output. Therefore add the name to
the id to make clearer that it's about a device on a muxed mdio bus.
In my case:
Now: mdio_mux-0.e40908ff:08
Before: 0.e40908ff:08
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/00b4bb1e-98f9-b4e7-5549-e095a4701f66@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Experimentation shows that PHY detect might fail when the code attempts
MDIO bus read immediately after clock enable. Add delay to stabilize the
clock before bus access.
PHY detect failure started to show after commit 7590fc6f80 ("net:
mdio: Demote probed message to debug print") that removed coincidental
delay between clock enable and bus access.
10ms is meant to match the time it take to send the probed message over
UART at 115200 bps. This might be a far overshoot.
Fixes: 23a890d493 ("net: mdio: Add the reset function for IPQ MDIO driver")
Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix loading of the driver when built as a module.
Fixes: f160e99462 ("net: phy: Add mdio-aspeed")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's build error while CONFIG_REGMAP_MMIO is not set
and CONFIG_MDIO_MSCC_MIIM=m.
ERROR: modpost: "__devm_regmap_init_mmio_clk"
[drivers/net/mdio/mdio-mscc-miim.ko] undefined!
Add the depend of REGMAP_MMIO to fix it.
Fixes: a27a762828 ("net: mdio: mscc-miim: convert to a regmap implementation")
Signed-off-by: Tianchen Ding <dtcccc@linux.alibaba.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20211130110209.804536-1-dtcccc@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the blamed commit, the second memory resource was not considered
anymore as optional. On some platforms like sparx5 the second resource
is optional. So add it back as optional and restore the comment that
says so.
Fixes: a27a762828 ("net: mdio: mscc-miim: convert to a regmap implementation")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch to a shared MDIO access implementation by way of the mdio-mscc-miim
driver.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Utilize regmap instead of __iomem to perform indirect mdio access. This
will allow for custom regmaps to be used by way of the mscc_miim_setup
function.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_ioremap() instead of ioremap() to avoid iounmap() missing.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The issue happened randomly in runtime. The message "Link is Down" is
popped but soon it recovered to "Link is Up".
The "Link is Down" results from the incorrect read data for reading the
PHY register via MDIO bus. The correct sequence for reading the data
shall be:
1. fire the command
2. wait for command done (this step was missing)
3. wait for data idle
4. read data from data register
Cc: stable@vger.kernel.org
Fixes: f160e99462 ("net: phy: Add mdio-aspeed")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20211125024432.15809-1-dylan_hung@aspeedtech.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The second resource is optional which is only provided on the chipset
IPQ5018. But the blamed commit ignores that and if the resource is
not there it just fails.
the resource is used like this,
if (priv->eth_ldo_rdy) {
val = readl(priv->eth_ldo_rdy);
val |= BIT(0);
writel(val, priv->eth_ldo_rdy);
fsleep(IPQ_PHY_SET_DELAY_US);
}
This patch reverts that to still allow the second resource to be optional
because other SoC have the some MDIO controller and doesn't need to
second resource.
Fixes: fa14d03e01 ("net: mdio-ipq4019: Make use of devm_platform_ioremap_resource()")
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210928134849.2092-1-caihuoqing@baidu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
According to the documentation the second resource is optional. But the
blamed commit ignores that and if the resource is not there it just
fails.
This patch reverts that to still allow the second resource to be
optional because other SoC have the some MDIO controller and doesn't
need to second resource.
Fixes: 672a1c3949 ("net: mdio: mscc-miim: Make use of the helper function devm_platform_ioremap_resource()")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When registering mdiobus children, if we get an -EPROBE_DEFER, we shouldn't
ignore it and continue registering the rest of the mdiobus children. This
would permanently prevent the deferring child mdiobus from working instead
of reattempting it in the future. So, if a child mdiobus needs to be
reattempted in the future, defer the entire mdio-mux initialization.
This fixes the issue where PHYs sitting under the mdio-mux aren't
initialized correctly if the PHY's interrupt controller is not yet ready
when the mdio-mux is being probed. Additional context in the link below.
Fixes: 0ca2997d14 ("netdev/of/phy: Add MDIO bus multiplexer support.")
Link: https://lore.kernel.org/lkml/CAGETcx95kHrv8wA-O+-JtfH7H9biJEGJtijuPVN0V5dUKUAB3A@mail.gmail.com/#t
Signed-off-by: Saravana Kannan <saravanak@google.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Marc Zyngier <maz@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we are seeing memory allocation errors, don't try to continue
registering child mdiobus devices. It's unlikely they'll succeed.
Fixes: 342fa19644 ("mdio: mux: make child bus walking more permissive and errors more verbose")
Signed-off-by: Saravana Kannan <saravanak@google.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Marc Zyngier <maz@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The whole point of devm_* APIs is that you don't have to undo them if you
are returning an error that's going to get propagated out of a probe()
function. So delete unnecessary devm_kfree() call in the error return path.
Fixes: b601616681 ("mdio: mux: Correct mdio_mux_init error path issues")
Signed-off-by: Saravana Kannan <saravanak@google.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Marc Zyngier <maz@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IPQ MDIO driver currently supports the chipset IPQ40xx, IPQ807x,
IPQ60xx and IPQ50xx.
Add the compatible 'qcom,ipq5018-mdio' because of ethernet LDO dedicated
to the IPQ5018 platform.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. configure the MDIO clock source frequency.
2. the LDO resource is needed to configure the ethernet LDO available
for CMN_PLL.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Oleksij Rempel