Add per port priority support for bonding active slave re-selection during
failover. A higher number means higher priority in selection. The primary
slave still has the highest priority. This option also follows the
primary_reselect rules.
This option could only be configured via netlink.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for reporting errors via extack in both bond_newlink
and bond_changelink.
Instead of having to look in the kernel log for why an option was not
correct just report the error to the user via the extack variable.
What is currently reported today:
ip link add bond0 type bond
ip link set bond0 up
ip link set bond0 type bond mode 4
RTNETLINK answers: Device or resource busy
After this change:
ip link add bond0 type bond
ip link set bond0 up
ip link set bond0 type bond mode 4
Error: unable to set option because the bond is up.
Signed-off-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Guard ns_targets in struct bond_params by CONFIG_IPV6, which could save
256 bytes if IPv6 not configed. Also add this protection for function
bond_is_ip6_target_ok() and bond_get_targets_ip6().
Remove the IS_ENABLED() check for bond_opts[] as this will make
BOND_OPT_NS_TARGETS uninitialized if CONFIG_IPV6 not enabled. Add
a dummy bond_option_ns_ip6_targets_set() for this situation.
Fixes: 4e24be018e ("bonding: add new parameter ns_targets")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Link: https://lore.kernel.org/r/20220531063727.224043-1-liuhangbin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This patch add a new bonding option ns_ip6_target, which correspond
to the arp_ip_target. With this we set IPv6 targets and send IPv6 NS
request to determine the health of the link.
For other related options like the validation, we still use
arp_validate, and will change to ns_validate later.
Note: the sysfs configuration support was removed based on
https://lore.kernel.org/netdev/8863.1645071997@famine
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new bonding parameter ns_targets to store IPv6 address.
Add required bond_ns_send/rcv functions first before adding
IPv6 address option setting.
Add two functions bond_send/rcv_validate so we can send/recv
ARP and NS at the same time.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When 802.3ad bond mode is configured the ad_actor_system option is set to
"00:00:00:00:00:00". But when trying to set the all-zeroes MAC as actors'
system address it was failing with EINVAL.
An all-zeroes ethernet address is valid, only multicast addresses are not
valid values.
Fixes: 171a42c38c ("bonding: add netlink support for sys prio, actor sys mac, and port key")
Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/20211221111345.2462-1-ffmancera@riseup.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, we use hard code number to verify if we are in the
arp_interval timeslice. But some user may want to reduce/extend
the verify timeslice. With the similar team option 'missed_max'
the uers could change that number based on their own environment.
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an option lacp_active, which is similar with team's runner.active.
This option specifies whether to send LACPDU frames periodically. If set
on, the LACPDU frames are sent along with the configured lacp_rate
setting. If set off, the LACPDU frames acts as "speak when spoken to".
Note, the LACPDU state frames still will be sent when init or unbind port.
v2: remove module parameter
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable ret is being initialized with a value that is never read,
it is being updated later on. The assignment is redundant and can be
removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Silence this warning by using strscpy_pad() directly:
drivers/net/bonding/bond_main.c:4877:3: warning: 'strncpy' specified bound 16 equals destination size [-Wstringop-truncation]
4877 | strncpy(params->primary, primary, IFNAMSIZ);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Additionally replace other strncpy() uses, as it is considered deprecated:
https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/lkml/202102150705.fdR6obB0-lkp@intel.com
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the incorrect interface name is stored in the slaves/active_slave
option of the bonding sysfs, the kernel does not record the log that
interface does not exist.
This patch adds a log for -ENODEV error, which will facilitate users to
figure out such issue.
Signed-off-by: Jianlin Lv <Jianlin.Lv@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This comes from an end-user request, where they're running multiple VMs on
hosts with bonded interfaces connected to some interest switch topologies,
where 802.3ad isn't an option. They're currently running a proprietary
solution that effectively achieves load-balancing of VMs and bandwidth
utilization improvements with a similar form of transmission algorithm.
Basically, each VM has it's own vlan, so it always sends its traffic out
the same interface, unless that interface fails. Traffic gets split
between the interfaces, maintaining a consistent path, with failover still
available if an interface goes down.
Unlike bond_eth_hash(), this hash function is using the full source MAC
address instead of just the last byte, as there are so few components to
the hash, and in the no-vlan case, we would be returning just the last
byte of the source MAC as the hash value. It's entirely possible to have
two NICs in a bond with the same last byte of their MAC, but not the same
MAC, so this adjustment should guarantee distinct hashes in all cases.
This has been rudimetarily tested to provide similar results to the
proprietary solution it is aiming to replace. A patch for iproute2 is also
posted, to properly support the new mode there as well.
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Thomas Davis <tadavis@lbl.gov>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Link: https://lore.kernel.org/r/20210119010927.1191922-1-jarod@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement TLS TX device offload for bonding interfaces.
This allows kTLS sockets running on a bond to benefit from the
device offload on capable lower devices.
To allow a simple and fast maintenance of the TLS context in SW and
lower devices, we bind the TLS socket to a specific lower dev.
To achieve a behavior similar to SW kTLS, we support only balance-xor
and 802.3ad modes, with xmit_hash_policy=layer3+4. This is enforced
in bond_sk_check(), done in a previous patch.
For the above configuration, the SW implementation keeps picking the
same exact lower dev for all the socket's SKBs. The device offload
behaves similarly, making the decision once at the connection creation.
Per socket, the TLS module should work directly with the lowest netdev
in chain, to call the tls_dev_ops operations.
As the bond interface is being bypassed by the TLS module, interacting
directly against the lower devs, there is no way for the bond interface
to disable its device offload capabilities, as long as the mode/policy
config allows it.
Hence, the feature flag is not directly controllable, but just reflects
the current offload status based on the logic under bond_sk_check().
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Boris Pismenny <borisp@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation for more cases that call netdev_update_features().
While here, move the features logic to the stage where struct bond
is already updated, and pass it as the only parameter to function
bond_set_xfrm_features().
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Boris Pismenny <borisp@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Don't try to adjust XFRM support flags if the bond device isn't yet
registered. Bad things can currently happen when netdev_change_features()
is called without having wanted_features fully filled in yet. This code
runs both on post-module-load mode changes, as well as at module init
time, and when run at module init time, it is before register_netdevice()
has been called and filled in wanted_features. The empty wanted_features
led to features also getting emptied out, which was definitely not the
intended behavior, so prevent that from happening.
Originally, I'd hoped to stop adjusting wanted_features at all in the
bonding driver, as it's documented as being something only the network
core should touch, but we actually do need to do this to properly update
both the features and wanted_features fields when changing the bond type,
or we get to a situation where ethtool sees:
esp-hw-offload: off [requested on]
I do think we should be using netdev_update_features instead of
netdev_change_features here though, so we only send notifiers when the
features actually changed.
Fixes: a3b658cfb6 ("bonding: allow xfrm offload setup post-module-load")
Reported-by: Ivan Vecera <ivecera@redhat.com>
Suggested-by: Ivan Vecera <ivecera@redhat.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Link: https://lore.kernel.org/r/20201205172229.576587-1-jarod@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
At the moment, bonding xfrm crypto offload can only be set up if the bonding
module is loaded with active-backup mode already set. We need to be able to
make this work with bonds set to AB after the bonding driver has already
been loaded.
So what's done here is:
1) move #define BOND_XFRM_FEATURES to net/bonding.h so it can be used
by both bond_main.c and bond_options.c
2) set BOND_XFRM_FEATURES in bond_dev->hw_features universally, rather than
only when loading in AB mode
3) wire up xfrmdev_ops universally too
4) disable BOND_XFRM_FEATURES in bond_dev->features if not AB
5) exit early (non-AB case) from bond_ipsec_offload_ok, to prevent a
performance hit from traversing into the underlying drivers
5) toggle BOND_XFRM_FEATURES in bond_dev->wanted_features and call
netdev_change_features() from bond_option_mode_set()
In my local testing, I can change bonding modes back and forth on the fly,
have hardware offload work when I'm in AB, and see no performance penalty
to non-AB software encryption, despite having xfrm bits all wired up for
all modes now.
Fixes: 18cb261afd ("bonding: support hardware encryption offload to slaves")
Reported-by: Huy Nguyen <huyn@mellanox.com>
CC: Saeed Mahameed <saeedm@mellanox.com>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jakub Kicinski <kuba@kernel.org>
CC: Steffen Klassert <steffen.klassert@secunet.com>
CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: netdev@vger.kernel.org
CC: intel-wired-lan@lists.osuosl.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dynamic key update for addr_list_lock still causes troubles,
for example the following race condition still exists:
CPU 0: CPU 1:
(RCU read lock) (RTNL lock)
dev_mc_seq_show() netdev_update_lockdep_key()
-> lockdep_unregister_key()
-> netif_addr_lock_bh()
because lockdep doesn't provide an API to update it atomically.
Therefore, we have to move it back to static keys and use subclass
for nest locking like before.
In commit 1a33e10e4a ("net: partially revert dynamic lockdep key
changes"), I already reverted most parts of commit ab92d68fc2
("net: core: add generic lockdep keys").
This patch reverts the rest and also part of commit f3b0a18bb6
("net: remove unnecessary variables and callback"). After this
patch, addr_list_lock changes back to using static keys and
subclasses to satisfy lockdep. Thanks to dev->lower_level, we do
not have to change back to ->ndo_get_lock_subclass().
And hopefully this reduces some syzbot lockdep noises too.
Reported-by: syzbot+f3a0e80c34b3fc28ac5e@syzkaller.appspotmail.com
Cc: Taehee Yoo <ap420073@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, gratuitous ARP/ND packets are sent every `miimon'
milliseconds. This commit allows a user to specify a custom delay
through a new option, `peer_notif_delay'.
Like for `updelay' and `downdelay', this delay should be a multiple of
`miimon' to avoid managing an additional work queue. The configuration
logic is copied from `updelay' and `downdelay'. However, the default
value cannot be set using a module parameter: Netlink or sysfs should
be used to configure this feature.
When setting `miimon' to 100 and `peer_notif_delay' to 500, we can
observe the 500 ms delay is respected:
20:30:19.354693 ARP, Request who-has 203.0.113.10 tell 203.0.113.10, length 28
20:30:19.874892 ARP, Request who-has 203.0.113.10 tell 203.0.113.10, length 28
20:30:20.394919 ARP, Request who-has 203.0.113.10 tell 203.0.113.10, length 28
20:30:20.914963 ARP, Request who-has 203.0.113.10 tell 203.0.113.10, length 28
In bond_mii_monitor(), I have tried to keep the lock logic readable.
The change is due to the fact we cannot rely on a notification to
lower the value of `bond->send_peer_notif' as `NETDEV_NOTIFY_PEERS' is
only triggered once every N times, while we need to decrement the
counter each time.
iproute2 also needs to be updated to be able to specify this new
attribute through `ip link'.
Signed-off-by: Vincent Bernat <vincent@bernat.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
All of these printk instances benefit from having both master and slave
device information included, so convert to using a standardized macro
format and remove redundant information.
Suggested-by: Joe Perches <joe@perches.com>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's currently a problem with toggling arp_validate on and off with an
active-backup bond. At the moment, you can start up a bond, like so:
modprobe bonding mode=1 arp_interval=100 arp_validate=0 arp_ip_targets=192.168.1.1
ip link set bond0 down
echo "ens4f0" > /sys/class/net/bond0/bonding/slaves
echo "ens4f1" > /sys/class/net/bond0/bonding/slaves
ip link set bond0 up
ip addr add 192.168.1.2/24 dev bond0
Pings to 192.168.1.1 work just fine. Now turn on arp_validate:
echo 1 > /sys/class/net/bond0/bonding/arp_validate
Pings to 192.168.1.1 continue to work just fine. Now when you go to turn
arp_validate off again, the link falls flat on it's face:
echo 0 > /sys/class/net/bond0/bonding/arp_validate
dmesg
...
[133191.911987] bond0: Setting arp_validate to none (0)
[133194.257793] bond0: bond_should_notify_peers: slave ens4f0
[133194.258031] bond0: link status definitely down for interface ens4f0, disabling it
[133194.259000] bond0: making interface ens4f1 the new active one
[133197.330130] bond0: link status definitely down for interface ens4f1, disabling it
[133197.331191] bond0: now running without any active interface!
The problem lies in bond_options.c, where passing in arp_validate=0
results in bond->recv_probe getting set to NULL. This flies directly in
the face of commit 3fe68df97c, which says we need to set recv_probe =
bond_arp_recv, even if we're not using arp_validate. Said commit fixed
this in bond_option_arp_interval_set, but missed that we can get to that
same state in bond_option_arp_validate_set as well.
One solution would be to universally set recv_probe = bond_arp_recv here
as well, but I don't think bond_option_arp_validate_set has any business
touching recv_probe at all, and that should be left to the arp_interval
code, so we can just make things much tidier here.
Fixes: 3fe68df97c ("bonding: always set recv_probe to bond_arp_rcv in arp monitor")
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a little improvement. If user use the
command shown as below, we should print the info [1]
instead of [2]. The eth0 exists actually, and it may
confuse user.
$ echo "eth0" > /sys/class/net/bond4/bonding/slaves
[1] "bond4: no command found in slaves file - use +ifname or -ifname"
[2] "write error: No such device"
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For some time now, if you load the bonding driver and configure bond
parameters via sysfs using minimal config options, such as specifying
nothing but the mode, relying on defaults for everything else, modes
that cannot use arp monitoring (802.3ad, balance-tlb, balance-alb) all
wind up with both arp_interval=0 (as it should be) and miimon=0, which
means the miimon monitor thread never actually runs. This is particularly
problematic for 802.3ad.
For example, from an LNST recipe I've set up:
$ modprobe bonding max_bonds=0"
$ echo "+t_bond0" > /sys/class/net/bonding_masters"
$ ip link set t_bond0 down"
$ echo "802.3ad" > /sys/class/net/t_bond0/bonding/mode"
$ ip link set ens1f1 down"
$ echo "+ens1f1" > /sys/class/net/t_bond0/bonding/slaves"
$ ip link set ens1f0 down"
$ echo "+ens1f0" > /sys/class/net/t_bond0/bonding/slaves"
$ ethtool -i t_bond0"
$ ip link set ens1f1 up"
$ ip link set ens1f0 up"
$ ip link set t_bond0 up"
$ ip addr add 192.168.9.1/24 dev t_bond0"
$ ip addr add 2002::1/64 dev t_bond0"
This bond comes up okay, but things look slightly suspect in
/proc/net/bonding/t_bond0 output:
$ grep -i mii /proc/net/bonding/t_bond0
MII Status: up
MII Polling Interval (ms): 0
MII Status: up
MII Status: up
Now, pull a cable on one of the ports in the bond, then reconnect it, and
you'll see:
Slave Interface: ens1f0
MII Status: down
Speed: 1000 Mbps
Duplex: full
I believe this became a major issue as of commit 4d2c0cda07, which for
802.3ad bonds, sets slave->link = BOND_LINK_DOWN, with a comment about
relying on link monitoring via miimon to set it correctly, but since the
miimon work queue never runs, the link just stays marked down.
If we simply tweak bond_option_mode_set() slightly, we can check for the
non-arp modes having no miimon value set, and insert BOND_DEFAULT_MIIMON,
which gets things back in full working order. This problem exists as far
back as 4.14, and might be worth fixing in all stable trees since, though
the work-around is to simply specify an miimon value yourself.
Reported-by: Bob Ball <ball@umich.edu>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a timing issue under active-standy mode, when bond_enslave() is
called, bond->params.primary might not be initialized yet.
Any time the primary slave string changes, bond->force_primary should be
set to true to make sure the primary becomes the active slave.
Signed-off-by: Xiangning Yu <yuxiangning@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 1386c36b30.
We don't want to encourage drivers to not report carrier status
correctly, therefore remove this commit.
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a mixed environment it may be difficult to tell if your hardware
support carrier, if it does not it can always report true. With a new
use_carrier option of 2, we can check both carrier and link status
sequentially, instead of one or the other
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rx load balancing provided by balance-alb is not mutually
exclusive with using hashing for tx selection, and should provide a decent
speed increase because this eliminates spinlocks and cache contention.
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace sscanf() with mac_pton().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass extack to do_set_master and down to ndo_add_slave
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit cbf5ecb305 ("net: bonding: Fix transmit load balancing in
balance-alb mode") tried to fix transmit dynamic load balancing in
balance-alb mode, which wasn't working after commit 8b426dc54c
("bonding: remove hardcoded value").
It turned out that my previous patch only fixed the case when
balance-alb was specified as bonding module parameter, and not when
balance-alb mode was set using /sys/class/net/*/bonding/mode (the most
common usage). In the latter case, tlb_dynamic_lb was set up according
to the default mode of the bonding interface, which happens to be
balance-rr.
This additional patch addresses this issue by setting up tlb_dynamic_lb
to 1 if "mode" is set to balance-alb through the sysfs interface.
I didn't add code to change tlb_balance_lb back to the default value for
other modes, because "mode" is usually set up only once during
initialization, and it's not worthwhile to change the static variable
bonding_defaults in bond_main.c to a global variable just for this
purpose.
Commit 8b426dc54c also changes the value of tlb_dynamic_lb for
balance-tlb mode if it is set up using the sysfs interface. I didn't
change that behavior, because the value of tlb_balance_lb can be changed
using the sysfs interface for balance-tlb, and I didn't like changing
the default value back and forth for balance-tlb.
As for balance-alb, /sys/class/net/*/bonding/tlb_balance_lb cannot be
written to. However, I think balance-alb with tlb_dynamic_lb set to 0
is not an intended usage, so there is little use making it writable at
this moment.
Fixes: 8b426dc54c ("bonding: remove hardcoded value")
Reported-by: Reinis Rozitis <r@roze.lv>
Signed-off-by: Kosuke Tatsukawa <tatsu@ab.jp.nec.com>
Cc: stable@vger.kernel.org # v4.12+
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bond_options.c file contains multiple netdev_info statements that clutter kernel output.
This patch replaces all netdev_info with netdev_dbg and adds a netdev_dbg statement for the
packets per slave parameter. Also fixes misalignment at line 467.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Michael J Dilmore <michael.j.dilmore@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever a user changes bonding options, a NETDEV_CHANGEINFODATA
notificatin is generated which results in a rtnelink message to
be sent. While runnig 'ip monitor', we can actually see 2 messages,
one a result of the event, and the other a result of state change
that is generated bo netdev_state_change(). However, this is not
always the case. If bonding changes were done via sysfs or ifenslave
(old ioctl interface), then only 1 message is seen.
This patch removes duplicate messages in the case of using netlink
to configure bonding. It introduceds a separte function that
triggers a netdev event and uses that function in the syfs and ioctl
cases.
This was discovered while auditing all the different envents and
continues the effort of cleaning up duplicated netlink messages.
CC: David Ahern <dsa@cumulusnetworks.com>
CC: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
No need to require the bond down while changing these settings, the change
will be reflected immediately and the 3ad mode will sort itself out.
For faster convergence set port->ntt to true in order to generate new
LACPDUs immediately.
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the bonding allows to set ad_actor_system and prio while the
bond device is down, but these are actually applied only if there aren't
any slaves yet (applied to bond device when first slave shows up, and to
slaves at 3ad bind time). After this patch changes are applied immediately
and the new values can be used/seen after the bond's upped so it's not
necessary anymore to release all and enslave again to see the changes.
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Create drivers/staging/rdma
- Move amso1100 driver to staging/rdma and schedule for deletion
- Move ipath driver to staging/rdma and schedule for deletion
- Add hfi1 driver to staging/rdma and set TODO for move to regular tree
- Initial support for namespaces to be used on RDMA devices
- Add RoCE GID table handling to the RDMA core caching code
- Infrastructure to support handling of devices with differing
read and write scatter gather capabilities
- Various iSER updates
- Kill off unsafe usage of global mr registrations
- Update SRP driver
- Misc. mlx4 driver updates
- Support for the mr_alloc verb
- Support for a netlink interface between kernel and user space cache
daemon to speed path record queries and route resolution
- Ininitial support for safe hot removal of verbs devices
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=EHLg
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull inifiniband/rdma updates from Doug Ledford:
"This is a fairly sizeable set of changes. I've put them through a
decent amount of testing prior to sending the pull request due to
that.
There are still a few fixups that I know are coming, but I wanted to
go ahead and get the big, sizable chunk into your hands sooner rather
than waiting for those last few fixups.
Of note is the fact that this creates what is intended to be a
temporary area in the drivers/staging tree specifically for some
cleanups and additions that are coming for the RDMA stack. We
deprecated two drivers (ipath and amso1100) and are waiting to hear
back if we can deprecate another one (ehca). We also put Intel's new
hfi1 driver into this area because it needs to be refactored and a
transfer library created out of the factored out code, and then it and
the qib driver and the soft-roce driver should all be modified to use
that library.
I expect drivers/staging/rdma to be around for three or four kernel
releases and then to go away as all of the work is completed and final
deletions of deprecated drivers are done.
Summary of changes for 4.3:
- Create drivers/staging/rdma
- Move amso1100 driver to staging/rdma and schedule for deletion
- Move ipath driver to staging/rdma and schedule for deletion
- Add hfi1 driver to staging/rdma and set TODO for move to regular
tree
- Initial support for namespaces to be used on RDMA devices
- Add RoCE GID table handling to the RDMA core caching code
- Infrastructure to support handling of devices with differing read
and write scatter gather capabilities
- Various iSER updates
- Kill off unsafe usage of global mr registrations
- Update SRP driver
- Misc mlx4 driver updates
- Support for the mr_alloc verb
- Support for a netlink interface between kernel and user space cache
daemon to speed path record queries and route resolution
- Ininitial support for safe hot removal of verbs devices"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (136 commits)
IB/ipoib: Suppress warning for send only join failures
IB/ipoib: Clean up send-only multicast joins
IB/srp: Fix possible protection fault
IB/core: Move SM class defines from ib_mad.h to ib_smi.h
IB/core: Remove unnecessary defines from ib_mad.h
IB/hfi1: Add PSM2 user space header to header_install
IB/hfi1: Add CSRs for CONFIG_SDMA_VERBOSITY
mlx5: Fix incorrect wc pkey_index assignment for GSI messages
IB/mlx5: avoid destroying a NULL mr in reg_user_mr error flow
IB/uverbs: reject invalid or unknown opcodes
IB/cxgb4: Fix if statement in pick_local_ip6adddrs
IB/sa: Fix rdma netlink message flags
IB/ucma: HW Device hot-removal support
IB/mlx4_ib: Disassociate support
IB/uverbs: Enable device removal when there are active user space applications
IB/uverbs: Explicitly pass ib_dev to uverbs commands
IB/uverbs: Fix race between ib_uverbs_open and remove_one
IB/uverbs: Fix reference counting usage of event files
IB/core: Make ib_dealloc_pd return void
IB/srp: Create an insecure all physical rkey only if needed
...
Some consumers of the netdev events API would like to know who is the
active slave when a NETDEV_CHANGEUPPER or NETDEV_BONDING_FAILOVER
events occur. For example, when managing RoCE GIDs, GIDs based on the
bond's ips should only be set on the port which corresponds to active
slave netdevice.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
num_grat_arp wasn't converted to the new bonding option API, so do this
now and remove the specific sysfs store option in order to use the
standard one. num_grat_arp is the same as num_unsol_na so add it as an
alias with the same option settings. An important difference is the option
name which is matched in bond_sysfs_store_option().
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/cadence/macb.c
drivers/net/phy/phy.c
include/linux/skbuff.h
net/ipv4/tcp.c
net/switchdev/switchdev.c
Switchdev was a case of RTNH_H_{EXTERNAL --> OFFLOAD}
renaming overlapping with net-next changes of various
sorts.
phy.c was a case of two changes, one adding a local
variable to a function whilst the second was removing
one.
tcp.c overlapped a deadlock fix with the addition of new tcp_info
statistic values.
macb.c involved the addition of two zyncq device entries.
skbuff.h involved adding back ipv4_daddr to nf_bridge_info
whilst net-next changes put two other existing members of
that struct into a union.
Signed-off-by: David S. Miller <davem@davemloft.net>
Before the patch, the command 'ip link add bond2 type bond mode 802.3ad'
causes the kernel to send a rtnl message for the bond2 interface, with an
ifindex 0.
'ip monitor' shows:
0: bond2: <BROADCAST,MULTICAST,MASTER> mtu 1500 state DOWN group default
link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff
9: bond2@NONE: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN group default
link/ether ea:3e:1f:53:92:7b brd ff:ff:ff:ff:ff:ff
[snip]
The patch fixes the spotted bug by checking in bond driver if the interface
is registered before calling the notifier chain.
It also adds a check in rtmsg_ifinfo() to prevent this kind of bug in the
future.
Fixes: d4261e5650 ("bonding: create netlink event when bonding option is changed")
CC: Jiri Pirko <jiri@resnulli.us>
Reported-by: Julien Meunier <julien.meunier@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds netlink support for the following bonding options:
* BOND_OPT_AD_ACTOR_SYS_PRIO
* BOND_OPT_AD_ACTOR_SYSTEM
* BOND_OPT_AD_USER_PORT_KEY
When setting the actor system mac address we assume the netlink message
contains a binary mac and not a string representation of a mac.
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
[jt: completed the setting side of the netlink attributes]
Signed-off-by: Jonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port key has three components - user-key, speed-part, and duplex-part.
The LSBit is for the duplex-part, next 5 bits are for the speed while the
remaining 10 bits are the user defined key bits. Get these 10 bits
from the user-space (through the SysFs interface) and use it to form the
admin port-key. Allowed range for the user-key is 0 - 1023 (10 bits). If
it is not provided then use zero for the user-key-bits (default).
It can set using following example code -
# modprobe bonding mode=4
# usr_port_key=$(( RANDOM & 0x3FF ))
# echo $usr_port_key > /sys/class/net/bond0/bonding/ad_user_port_key
# echo +eth1 > /sys/class/net/bond0/bonding/slaves
...
# ip link set bond0 up
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@redhat.com>
[jt: * fixed up style issues reported by checkpatch
* fixed up context from change in ad_actor_sys_prio patch]
Signed-off-by: Jonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In an AD system, the communication between actor and partner is the
business between these two entities. In the current setup anyone on the
same L2 can "guess" the LACPDU contents and then possibly send the
spoofed LACPDUs and trick the partner causing connectivity issues for
the AD system. This patch allows to use a random mac-address obscuring
it's identity making it harder for someone in the L2 is do the same thing.
This patch allows user-space to choose the mac-address for the AD-system.
This mac-address can not be NULL or a Multicast. If the mac-address is set
from user-space; kernel will honor it and will not overwrite it. In the
absence (value from user space); the logic will default to using the
masters' mac as the mac-address for the AD-system.
It can be set using example code below -
# modprobe bonding mode=4
# sys_mac_addr=$(printf '%02x:%02x:%02x:%02x:%02x:%02x' \
$(( (RANDOM & 0xFE) | 0x02 )) \
$(( RANDOM & 0xFF )) \
$(( RANDOM & 0xFF )) \
$(( RANDOM & 0xFF )) \
$(( RANDOM & 0xFF )) \
$(( RANDOM & 0xFF )))
# echo $sys_mac_addr > /sys/class/net/bond0/bonding/ad_actor_system
# echo +eth1 > /sys/class/net/bond0/bonding/slaves
...
# ip link set bond0 up
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@redhat.com>
[jt: fixed up style issues reported by checkpatch]
Signed-off-by: Jonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows user to randomize the system-priority in an ad-system.
The allowed range is 1 - 0xFFFF while default value is 0xFFFF. If user
does not specify this value, the system defaults to 0xFFFF, which is
what it was before this patch.
Following example code could set the value -
# modprobe bonding mode=4
# sys_prio=$(( 1 + RANDOM + RANDOM ))
# echo $sys_prio > /sys/class/net/bond0/bonding/ad_actor_sys_prio
# echo +eth1 > /sys/class/net/bond0/bonding/slaves
...
# ip link set bond0 up
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@redhat.com>
[jt: * fixed up style issues reported by checkpatch
* changed how the default value is set in bond_check_params(), this
makes the default consistent between what gets set for a new bond
and what the default is claimed to be in the bonding options.]
Signed-off-by: Jonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: Jonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the empty array element initializer and size the array with
BOND_OPT_LAST so the compiler will complain if more elements are in
there than should be.
An interesting unwanted side effect of this initializer is that if one
inserts new options into the middle of the array then this initializer
will zero out the option that equals BOND_OPT_TLB_DYNAMIC_LB+1.
Example:
Extend the OPTS enum:
enum {
...
BOND_OPT_TLB_DYNAMIC_LB,
BOND_OPT_LACP_NEW1,
BOND_OPT_LAST
};
Now insert into bond_opts array:
static const struct bond_option bond_opts[] = {
...
[BOND_OPT_LACP_RATE] = { .... unchanged stuff .... },
[BOND_OPT_LACP_NEW1] = { ... new stuff ... },
...
[BOND_OPT_TLB_DYNAMIC_LB] = { .... unchanged stuff ....},
{ } // MARK A
};
Since BOND_OPT_LACP_NEW1 = BOND_OPT_TLB_DYNAMIC_LB+1, the last
initializer (MARK A) will overwrite the contents of BOND_OPT_LACP_NEW1
and can be easily viewed with the crash utility.
Signed-off-by: Jonathan Toppins <jtoppins@cumulusnetworks.com>
Cc: Andy Gospodarek <gospo@cumulusnetworks.com>
Cc: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This ways drivers like cxgb4 don't need to do ugly relative includes.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly all users of curr_slave_lock already have RTNL as we've discussed
previously so there's no point in using it, the one case where the lock
must stay is the 3ad code, in fact it's the only one.
It's okay to remove it from bond_do_fail_over_mac() as it's called with
RTNL and drops the curr_slave_lock anyway.
bond_change_active_slave() is one of the main places where
curr_slave_lock was used, it's okay to remove it as all callers use RTNL
these days before calling it, that's why we move the ASSERT_RTNL() in
the beginning to catch any potential offenders to this rule.
The RTNL argument actually applies to all of the places where
curr_slave_lock has been removed from in this patch.
Also remove the unnecessary bond_deref_active_protected() macro and use
rtnl_dereference() instead.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu