Device 'new_id' interface is useful for testing of not yet published
hardware on older kernels and for internally used device ids on
simulation platforms.
However currently with the device configuration held in device_id driver
data as a pointer to mei_cfg structure it is hard, as one need to locate
the address of the correct structure.
A recommended way of doing that is to use and index instead of a
pointer.
This patch adds a new list of configuration mei_cfg_list[]
indexed via enum mei_cfg_idx.
In addition it cleanups ich platform naming, renames legacy
generation to ich and what was ich to ich10.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In rare case the driver may lose connection with the device after device
reset due to a missed interrupt. The driver will unlock the flow by
generating an interrupt towards the firmware (HIG) when the device is in
the resetting state. The FW is able to ignore the interrupt during
orderly flow. The effected platforms are skylake and newer.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Consolidate setting H_IG, an interrupt from host towards hw,
into a wrapper to eliminate code duplication.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_ and pcim_ functions to make error handling
simpler and code smaller and tidier.
Based on original patch by
mei: me: use managed functions pcim_* and devm_*
https://lkml.org/lkml/2016/2/1/339
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mei_dev structure used struct mei_cl_cb type variables as for holding
callbacks list heads. Replace them by the actual struct list_head
as there is no other info that is handled. This slims down
the mei_dev structure and mostly streamline the code.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the newer HW sports two interrupts causes we cannot
just simply acknowledge the interrupts directly in the quick handler
and store the cause in the member variable, as the cause
will be overridden upon next interrupt while the interrupt thread
was not yet scheduled handling the previous interrupt.
The simple fix is to disable interrupts in quick handler
and acknowledge and enabled them in the interrupt thread.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to synchronize irqs before issuing reset to make sure that the
clients communication is concluded and doesn't leak to the reset flow
and confusing the state machine.
This issue is happening during suspend/resume stress testing.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The write buffer should not by modified so make it constant. Also
hitchhike some style fixes on the way in the interface and rename
mei_me_write_message to mei_me_hbuf_write for consistency.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Schedule link reset if failed to perform runtime suspend or resume.
Set active runtime pm stte on link reset
to clean runtimr pm error, if present.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sunrise Point PCH with SPS Firmware doesn't expose working
MEI interface, we need to quirk it out.
The SPS Firmware is identifiable only on the first PCI function
of the device.
Cc: <stable@vger.kernel.org> #4.6+
Tested-by: Sujith Pandel <sujith_pandel@dell.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use tracing events also for reading and writing pci configuration space
<debugfs>/tracing/events/mei/mei_pci_reg_{read,write}
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A BIOS may put the device in d0i3 on platform initialization so it won’t
consume power even if the driver is not present, in turn the driver has
to wake up the devices on load in order to perform the initialization
sequence and move it back to low power state on driver remove.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move mei_me_hw_reset down in the source file to avoid
forward declarations when introducing d0i3 flow in the next patch.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rework mei power gating state machine to support entry and exit to and
from D0i3 power state.
The choice between legacy and D0i3 routines is conditioned on
d0i3_supported flag.
The patch introduces warning:
drivers/misc/mei/hw-me.c:901:12: warning: ‘mei_me_d0i3_enter’ defined but not used [-Wunused-function]
it will go away in consequent patch
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
D0i3 adds additional interrupt reason bit, therefore we add a variable
intr_source to save the interrupt causes for further dispatching.
The interrupt cause is saved in the irq quick handler to achieve
unified behavior for both MSI enabled and shared interrupt platforms.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Detect d0i3 low power state during hw configuration,
the value is set in HFS_1 pci config reigister.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the hbm power gating state machine so it will wait till it receives
confirmation interrupt for the PG_ISOLATION_EXIT message.
In process of the suspend flow the devices first have to exit from the
power gating state (runtime pm resume).
If we do not handle the confirmation interrupt after sending
PG_ISOLATION_EXIT message, we may receive it already after the suspend
flow has changed the device state and interrupt will be interpreted as a
spurious event, consequently link reset will be invoked which will
prevent the device from completing the suspend flow
kernel: [6603] mei_reset:136: mei_me 0000:00:16.0: powering down: end of reset
kernel: [476] mei_me_irq_thread_handler:643: mei_me 0000:00:16.0: function called after ISR to handle the interrupt processing.
kernel: mei_me 0000:00:16.0: FW not ready: resetting
Cc: <stable@vger.kernel.org> #3.18+
Cc: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=86241
Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=770397
Tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current power gating naming was confusing,
we wish to swap meanings of register and flow level power gating terms,
For registers writing level use terms set and unset:
mei_me_pg_set, mei_me_pg_unset
For flow/high level use power gating enter and power gating exit terms
mei_me_pg_enter_sync, mei_me_pg_exit_sync
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To make debugging a bit easier we add me register
access tracing
<debugfs>/tracing/events/mei/mei_reg_{read,write}
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. Use mei_device structure as the first argument to the io
register access wrappers so we'll have access to the device
structure needed for tracing.
2. Use wrapper consistently
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We might enter the interrupt handler with hw_ready already set,
but prior we actually started the reset flow.
To soleve this we move the reset release from the interrupt handler
to the HW start wait function which is part of the reset sequence.
Cc: <stable@vger.kernel.org> #3.10+
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should mask interrupt set bit when writing back
hcsr value in reset bit clean-up.
This is refinement for
mei: clean reset bit before reset
commit b13a65ef19
Cc: <stable@vger.kernel.org> #3.10+
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
H_RST bit in H_CSR register may be found lit before reset is started,
for example if preceding reset flow hasn't completed.
In that case asserting H_RST will be ignored, therefore we need to clean
H_RST bit to start a successful reset sequence.
Cc: <stable@vger.kernel.org> #3.10+
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ME devices prior to PCH8 (Lynx Point) have two FW status registers,
on PCH8 and newer excluding txe there are six FW status registers.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kill host_hw_status and me_hw_state from me hw structure that used
to cache host and me csr values.
We do not use the cached values across the function calls anymore
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device specific configurations are currently only needed by me hw
so we can remove it from txe
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For purpose of adding testing HW we would like
to get rid of pci dependency in generic mei code.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fw status retrieval has pci specific implementation
so we push it back to the hw layer
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For purpose of adding testing HW we would like
to get rid of pci dependency in generic mei code
This patch provides only straight forward changes
FW status and prob quirks need to be handled separately
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Setting of hw_ops and device has should be in
mei_device_init.
We add reference to the parent device and remove
pci dependent cfg
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fix new style warning: Missing a blank line after declarations
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
extract supported hbm features and commands from the hbm version
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We cannot handle user interrupt in context of hw initialization
so we only wait for time out which is reasonably short
Also we don't need to check error from wait, only flag value.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We introduced unified FW status function in patch
mei: add per device configuration (lkml.org/lkml/2014/5/12/607)
This change made hw_ops functions unused and obsolete
therefore we remove these functions from source code.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move quirk FW type detector to cfg structure
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add mei_cfg structure that holds per device configuration
data and hooks, as the first step we add firmware
status register offsets
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According the spec the host should read H_CSR again
after asserting reset H_RST to ensure that reset was
read by the firmware
Cc: stable@vger.kernel.org
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It my take time till ME_RDY will be cleared after the reset,
so we cannot check the bit before we got the interrupt
Cc: stable@vger.kernel.org
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We cleared H_RST for H_CSR on spurious interrupt generated when ME_RDY
while cleared and not while ME_RDY is set. The spurious interrupt
is not delivered on all platforms in this case the
driver may fail to initialize.
Cc: stable@vger.kernel.org
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fetch FW status registers, as they are important in
in understanding of FW reset reasons
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For power gating entry we write hbm pg entry request command and
then we set pg register
For power gating exit we clear pg register and wait for exit request
hbm command.
Exit power gating request might also be initiated by the firmware
w/o explicit driver request
The power gating state is tracked by pg_state member of me_hw
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the runtime pm and the internal power gating
cannot be in complete sync in regards to I/O
operations, we need to expose the device
hardware internal power gating state to mei layer
2. We add pg_state handler that translate the hw
internal pg state to mei layer
2. We add power gating event variable to keep
power track of power gating transitions
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Reviewed-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable power gating isolation only if hw and fw support it.
This is indicated by ME_PGIC_HRA bit in ME_CSR_HA register
and on HBM protocol version.
The information is exported to MEI layer through
new pg_is_enabled hw op.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove includes of me-hw.h and me-hw-regs.h headers from
the mei generic code.
The mei layer should not depend on hw specific headers
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tomas Winkler