It's pointless to scan the hub' i2c-bus segment if GPIOs aren't supported
by the system, since no GPIO-driven reset could be cleared by the driver
then. Moreover if CONFIG_GPIOLIB is disabled the gpio_chip structure
definition won't be available, which causes the incomplete type pointer
dereference compilation error. In order to fix this we need to create an
empty usb251x_check_gpio_chip() method returning zero, so the driver would
skip the i2c-bus segment checking and proceed with further probing in this
case.
Fixes: 6e3c8beb4f ("usb: usb251xb: Lock i2c-bus segment the hub resides")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SMBus slave configuration is activated by CFG_SEL[1:0]=0x1 pins
state. This is the mode the hub is supposed to be to let this driver
work correctly. But a race condition might happen right after reset
is cleared due to CFG_SEL[0] pin being multiplexed with SMBus SCL
function. In case if the reset pin is handled by a i2c GPIO expander,
which is also placed at the same i2c-bus segment as the usb251x
SMB-interface connected to, then the hub reset clearance might
cause the CFG_SEL[0] being latched in unpredictable state. So
sometimes the hub configuration mode might be 0x1 (as expected),
but sometimes being 0x0, which doesn't imply to have the hub SMBus-slave
interface activated and consequently causes this driver failure.
In order to fix the problem we must make sure the GPIO-reset chip doesn't
reside the same i2c-bus segment as the SMBus-interface of the hub. If
it doesn't, we can safely block the segment for the time the reset is
cleared to prevent anyone generating a traffic at the i2c-bus SCL lane
connected to the CFG_SEL[0] pin. But if it does, nothing we can do, so
just return an error. If we locked the i2c-bus segment and tried to
communicate with the GPIO-expander, it would cause a deadlock. If we didn't
lock the i2c-bus segment, it would randomly cause the CFG_SEL[0] bit flip.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the driver tries to get optional clock, it ignores all errors except
-EPROBE_DEFER, but if only ignores -ENOENT, it will cover some real errors,
such as -ENOMEM, so use devm_clk_get_optional() to get optional clock.
And remove unnecessary stack variable clk.
Cc: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_match_device in usb251xb_probe can fail and returns a NULL pointer.
The patch avoids a potential NULL pointer dereference in this scenario.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Reviewed-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to compare *port* with >= 0 because such comparison
of an unsigned value is always true.
Fix this by removing such comparison.
Addresses-Coverity-ID: 1443949 ("Unsigned compared against 0")
Fixes: 02a50b8750 ("usb: usb251xb: add usb data lane port swap feature")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dwc3 now works on TI's AM6xx platforms. Also on dwc3 we have a few
changes which improve request cancellation and some improvements to
how we print to the trace buffer.
Renesas_usb3 got support for r8a774c0 device.
Dwc2 got scatter-gather support.
Apart from these, the usual set of minor fixes and all sorts of small
details.
-----BEGIN PGP SIGNATURE-----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=4fTL
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: changes for v5.1 merge window
Dwc3 now works on TI's AM6xx platforms. Also on dwc3 we have a few
changes which improve request cancellation and some improvements to
how we print to the trace buffer.
Renesas_usb3 got support for r8a774c0 device.
Dwc2 got scatter-gather support.
Apart from these, the usual set of minor fixes and all sorts of small
details.
* tag 'usb-for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (40 commits)
usb: phy: twl6030-usb: fix possible use-after-free on remove
usb: misc: usbtest: add super-speed isoc support
usb: dwc3: Reset num_trbs after skipping
usb: dwc3: gadget: don't enable interrupt when disabling endpoint
fotg210-udc: pass struct device to DMA API functions
fotg210-udc: remove a bogus dma_sync_single_for_device call
usb: gadget: Change Andrzej Pietrasiewicz's e-mail address
usb: f_fs: Avoid crash due to out-of-scope stack ptr access
usb: dwc3: haps: Workaround matching VID PID
usb: gadget: f_fs: preserve wMaxPacketSize across usb_ep_autoconfig() call
usb: gadget: move non-super speed code out of usb_ep_autoconfig_ss()
usb: gadget: function: sync f_uac1 ac header baInterfaceNr
usb: dwc2: gadget: Add scatter-gather mode
usb: gadget: fix various indentation issues
usb: dwc2: Fix EP TxFIFO number setting
udc: net2280: Fix net2280_disable
USB: gadget: Improve kerneldoc for usb_ep_dequeue()
usb: dwc3: debug: purge usage of strcat
usb: dwc3: trace: pass trace buffer size to decoding functions
usb: dwc3: gadget: remove DWC3_EP_END_TRANSFER_PENDING
...
The calculation of packet number within microframe is different between
high-speed and super-speed endpoint, we add support for super-speed
in this patch.
Cc: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fixes the following coccinelle warning:
./drivers/usb/misc/ftdi-elan.c:972:10-12: WARNING: possible condition with no effect (if == else)
./drivers/usb/misc/ftdi-elan.c:983:9-11: WARNING: possible condition with no effect (if == else)
./drivers/usb/misc/ftdi-elan.c:2052:11-13: WARNING: possible condition with no effect (if == else)
All these else/if branches just do the same thing actually as the last else branch,
So it can be merged into the last branch.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB3503 chip can be used without any I2C connection, what is handled by
a simple platform device driver. Add support for resetting the chip (via
GPIO lines) during system suspend/resume cycle by adding calls to existing
suspend/resume functions used for E2C device.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove macros which are only wrappers around standard operations. When
we expand them into code, we see that sisusbcon_memsetw can simply use
memset16 and sisusbcon_putcs can just call memcpy. So make the code
compact.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the previous patch we see, that whole files are ifdeffed depending
on CONFIG options. So do not build the files at all if the CONFIG is not
enabled. (I.e. move the check from .c to Makefile.)
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two macros defined:
1) ifdef CONFIG_COMPAT => define SISUSB_NEW_CONFIG_COMPAT
2) ifdef CONFIG_USB_SISUSBVGA_CON => define INCL_SISUSB_CON
Remove the latter and make use only of the former. This removes one
layer of obfuscation.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert SISUSB_VADDR and SISUSB_HADDR to inline functions. Now, there
are no more hidden accesses to local variables (vc_data and
sisusb_usb_data).
sisusb_haddr returns unsigned long from now on, not u16 *, as ulong is
what every caller expects -- we can remove some casts.
Call sites were aligned to be readable too.
Use sisusb_haddr on 4 more places in sisusbcon_blank and
sisusbcon_scroll. It was open coded there with [x, y] being [0, 0].
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable 'empty_packets' does not used in any other places
except for self increment, so it can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a few remaining drivers/usb/ files that do not have SPDX
identifiers in them, all of these are either Kconfig or Makefiles. Add
the correct GPL-2.0 identifier to them to make scanning tools happy.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The HW can swap the USB differential-pair (D+/D-) for each port
separately. So the USB signals can be re-aligned with a misplaced
USB connector on the PCB.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The spinlock was inside the urb completion function which is only
called once per display and is then resubmitted from this function.
There was no other place where this lock was used.
Signed-off-by: Alexander Theissen <alex.theissen@me.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver does allocate a DMA address with usb_alloc_coherent but did
not set the appropriate flag to signal that transfer_dma is set to a
valid value.
Signed-off-by: Alexander Theissen <alex.theissen@me.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add another Apple Cinema Display to the list of supported displays.
Signed-off-by: Alexander Theissen <alex.theissen@me.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add another Apple Cinema Display to the list of supported displays
Signed-off-by: Mattias Jacobsson <2pi@mok.nu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Upon success the update_status handler returns a positive number
corresponding to the number of bytes transferred by usb_control_msg.
However the return code of the update_status handler should indicate if
an error occurred(negative) or how many bytes of the user's input to sysfs
that was consumed. Return code zero indicates all bytes were consumed.
The bug can for example result in the update_status handler being called
twice, the second time with only the "unconsumed" part of the user's input
to sysfs. Effectively setting an incorrect brightness.
Change the update_status handler to return zero for all successful
transactions and forward usb_control_msg's error code upon failure.
Signed-off-by: Mattias Jacobsson <2pi@mok.nu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
simple_strtoul is obsolete, and use kstrtoint instead
Signed-off-by: Ding Xiang <dingxiang@cmss.chinamobile.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A common flaw in the kernel is integer overflow during memory allocation
size calculations. In an effort to reduce the frequency of these bugs,
kmalloc_array was implemented, which allocates memory for an array,
while at the same time detects integer overflow.
This patch replaces cases of:
kmalloc(a * b, gfp)
with:
kmalloc_array(a, b, gfp)
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
async_complete() in uss720.c is a completion handler function for the
USB driver. So it should not sleep, but it is can sleep according to the
function call paths (from bottom to top) in Linux-4.16.
[FUNC] set_1284_register(GFP_KERNEL)
drivers/usb/misc/uss720.c, 372:
set_1284_register in parport_uss720_frob_control
drivers/parport/ieee1284.c, 560:
[FUNC_PTR]parport_uss720_frob_control in parport_ieee1284_ack_data_avail
drivers/parport/ieee1284.c, 577:
parport_ieee1284_ack_data_avail in parport_ieee1284_interrupt
./include/linux/parport.h, 474:
parport_ieee1284_interrupt in parport_generic_irq
drivers/usb/misc/uss720.c, 116:
parport_generic_irq in async_complete
[FUNC] get_1284_register(GFP_KERNEL)
drivers/usb/misc/uss720.c, 382:
get_1284_register in parport_uss720_read_status
drivers/parport/ieee1284.c, 555:
[FUNC_PTR]parport_uss720_read_status in parport_ieee1284_ack_data_avail
drivers/parport/ieee1284.c, 577:
parport_ieee1284_ack_data_avail in parport_ieee1284_interrupt
./include/linux/parport.h, 474:
parport_ieee1284_interrupt in parport_generic_irq
drivers/usb/misc/uss720.c, 116:
parport_generic_irq in async_complete
Note that [FUNC_PTR] means a function pointer call is used.
To fix these bugs, GFP_KERNEL is replaced with GFP_ATOMIC.
These bugs are found by my static analysis tool DSAC.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
snprintf() always returns the full length of the string it could have
printed, even if it was truncated because the buffer was too small.
So in case the counter value is truncated, we will over-read from
in_buffer and over-write to the caller's buffer.
I don't think it's actually possible for this to happen, but in case
truncation occurs, WARN and return -EIO.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the written data starts with a digit, yurex_write() tries to parse
it as an integer using simple_strtoull(). This requires a null-
terminator, and currently there's no guarantee that there is one.
(The sample program at
https://github.com/NeoCat/YUREX-driver-for-Linux/blob/master/sample/yurex_clock.pl
writes an integer without a null terminator. It seems like it must
have worked by chance!)
Always add a null byte after the written data. Enlarge the buffer
to allow for this.
Cc: stable@vger.kernel.org
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable modey is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'modey' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pointer usbdev is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'usbdev' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In general, accessing userspace memory beyond the length of the supplied
buffer in VFS read/write handlers can lead to both kernel memory corruption
(via kernel_read()/kernel_write(), which can e.g. be triggered via
sys_splice()) and privilege escalation inside userspace.
Fix it by using simple_read_from_buffer() instead of custom logic.
Fixes: 6bc235a2e2 ("USB: add driver for Meywa-Denki & Kayac YUREX")
Signed-off-by: Jann Horn <jannh@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Cc: Juergen Stuber <starblue@users.sourceforge.net>
Cc: legousb-devel@lists.sourceforge.net
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The intr_idx_lock lock is acquired only in the completion callback of
the ->int_in_urb (iowarrior_callback()). There is only one URB that is
scheduled / completed so there can't be more than one user of the lock.
The comment says that it protects ->intr_idx and the callback is the
only place in driver that writes to it.
Remove the intr_idx_lock lock because it is superfluous.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trivial fix to spelling mistake in text string
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of tty and serial driver patches for 4.17-rc1
Not all that big really, most are just small fixes and additions to
existing drivers. There's a bunch of work on the imx serial driver
recently for some reason, and a new embedded serial driver added as
well.
Full details are in the shortlog.
All of these have been in the linux-next tree for a while with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWsSn+w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynb6wCdEf5dAUrSB37ptZY78n4kc6nI6NAAniDO+rjL
ppZZp7QTIB/bnPfW8cOH
=+tfY
-----END PGP SIGNATURE-----
Merge tag 'tty-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty and serial driver patches for 4.17-rc1
Not all that big really, most are just small fixes and additions to
existing drivers. There's a bunch of work on the imx serial driver
recently for some reason, and a new embedded serial driver added as
well.
Full details are in the shortlog.
All of these have been in the linux-next tree for a while with no
reported issues"
* tag 'tty-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (66 commits)
serial: expose buf_overrun count through proc interface
serial: mvebu-uart: fix tx lost characters
tty: serial: msm_geni_serial: Fix return value check in qcom_geni_serial_probe()
tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP
8250-men-mcb: add support for 16z025 and 16z057
powerpc: Mark the variable earlycon_acpi_spcr_enable maybe_unused
serial: stm32: fix initialization of RS485 mode
ARM: dts: STi: Remove "console=ttyASN" from bootargs for STi boards
vt: change SGR 21 to follow the standards
serdev: Fix typo in serdev_device_alloc
ARM: dts: STi: Fix aliases property name for STi boards
tty: st-asc: Update tty alias
serial: stm32: add support for RS485 hardware control mode
dt-bindings: serial: stm32: add RS485 optional properties
selftests: add devpts selftests
devpts: comment devpts_mntget()
devpts: resolve devpts bind-mounts
devpts: hoist out check for DEVPTS_SUPER_MAGIC
serial: 8250: Add Nuvoton NPCM UART
serial: mxs-auart: disable clks of Alphascale ASM9260
...
Reporting two more VID/PID pairs that work with this driver, having used
an informational webpage <http://reboots.g-cipher.net/lcd/> as a buying
guide now. The page listed additional working VID/PID pairs but did not
include these two. None were upstreamed. Also taking this opportunity to
sort the pairs numerically.
Of the two such cables now in my possession, one is white, bearing the
In-System Design ISD-103 label on one side, sold as an Epson CAEUL0002
"USB to Parallel Smart Cable For Apple Macintosh Computers" (04b8:0002),
and the other is black, bearing the In-System Design ISD-101 label on one
side, sold as an early Belkin F5U002 (05ab:0002).
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add waiting for an URB transmit finish that let the last URB to be sent
(to be not discarded) during 'release' procedure. W/o this waiting,the
last frame will be nearly always lost.
A test case: an attempt of sending a single frame:
echo -en "\001mk255" >/dev/adutux0
Signed-off-by: Kirill Kapranov <kirill.kirillovich.kapranov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel would like to have all stack VLA usage removed[1]. We
already have a pre-processor constant defined MAX_SGLEN. We can use
this instead of the variable param-sglen.
[1]: https://lkml.org/lkml/2018/3/7/621
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This expands the no-op dummy functions into full prototypes to avoid
indirect call mismatches when running under Control Flow Integrity
checking, like with Clang's -fsanitize=cfi.
Co-Developed-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As done in commit:
724ba8b30b ("console/dummy: leave .con_font_get set to NULL")
This drops the dummy .con_font_get(), as it could leave arguments
uninitialized.
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of kmalloc() with manually calculated values followed by
multiple strcpy()/strcat() calls, just fold it all into a single
kasprintf() call.
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Serge Semin