DAPM operations are always performed on the card as a whole. Yet (primarily for
historic reasons) dapm_power_widgets() takes a DAPM context as its parameter.
The DAPM context is mainly used to look up a pointer to the card. The same is
true for a couple of functions that are being called from dapm_power_widgets().
This patch changes the signature of dapm_power_widgets() and a couple of related
functions to take a snd_soc_card instead of a snd_soc_dapm_context.
Some of the functions also use the DAPM's device to print error and debug
messages. This can be a bit confusing though since this means the messages for
all widgets, also those from other contexts, will be printed with that device.
The patch updates those cases to use the device of the widget's DAPM context.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The update field of a DAPM context is only assigned while the card's dapm_mutex
is locked, the field is also cleared again while the mutex is stil locked. So
there will only ever be one DAPM context at a time with a non-NULL update field.
So it is safe to move the update field from the DAPM context struct to the card
struct. Doing so will allow further cleanups in this area.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use snd_soc_dapm_mixer_update_power() instead of reimplementing its
functionality.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
In order to avoid race conditions the assignment of dapm->update should happen
while card->dapm_mutex is being held. To allow CODEC drivers to run a register
update when using snd_soc_dapm_mux_update_power() or
snd_soc_dapm_mixer_update_power() add a update parameter to these two functions.
The update parameter will be assigned to dapm->update while card->dapm_mutex is
locked.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently when updating a control that is shared between multiple widgets the
whole power-up/power-down sequence is being run once for each widget. The
control register is updated during the first run, which means the CODEC internal
routing is also updated for all widgets during this first run. The input and
output paths for each widgets are only updated though during the respective run
for that widget. This leads to a slight inconsistency between the CODEC's
internal state and ASoC's state, which causes non optimal behavior in regard to
click and pop avoidance.
E.g. consider the following setup where two MUXs share the same control.
+------+
A1 ------| |
| MUX1 |----- C1
B1 ------| |
+------+
|
control ---+
|
+------+
A2 ------| |
| MUX2 |----- C2
B2 ------| |
+------+
If the control is updated to switch the MUXs from input A to input B with the
current code the power-up/power-down sequence will look like this:
Run soc_dapm_mux_update_power for MUX1
Power-down A1
Update MUXing
Power-up B1
Run soc_dapm_mux_update_power for MUX2
Power-down A2
(Update MUXing)
Power-up B2
Note that the second 'Update Muxing' is a no-op, since the register was already
updated.
While the preferred order for avoiding pops and clicks should be:
Run soc_dapm_mux_update_power for control
Power-down A1
Power-down A2
Update MUXing
Power-up B1
Power-up B2
This patch changes the behavior to the later by running the updates for all
widgets that the control is attached to at the same time.
The new code is also a bit simpler since callers of
soc_dapm_{mux,muxer}_update_power don't have to loop over each widget anymore
and neither do we need to keep track for which of the kcontrol's widgets the
current update is.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
soc_dpcm_runtime_update() operates on a ASoC card as a whole. Currently it takes
a snd_soc_dapm_widget as its only parameter though. The widget is then used to
look up the card and is otherwise unused. This patch changes the function to
take a pointer to the card directly. This makes it possible to to call
soc_dpcm_runtime_update() for updates which are not related to one specific
widget.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
As noticed by Lars-Peter Clausen since the move to using widgets to hook
into the DAIs we no longer directly manage the power of AIF or DAC/ADC
widgets from the stream integration so they can just use the generic power
checks instead of the custom stream integration ones they currently do.
Signed-off-by: Mark Brown <broonie@linaro.org>
The ALSA core expect the put callback of a control to return 1 if the value of
the control changed and 0 if it did not. Both snd_soc_dapm_put_volsw() and
snd_soc_dapm_put_enum_virt() currently always returns 0. For both functions we
already have a 'change' variable which either contains 1 or 0 depending on
whether the value has changed or not, so just return that.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
These two functions were added two years ago in commit 4805608 ("ASoC: dapm -
Add methods to retrieve snd_card and soc_card from dapm context.") but have
remained unused so far. Considering that the dapm context actually has a direct
pointer to the card the functions also seem to be unnecessary. E.g. the
expressions 'dapm_get_soc_card(dapm)' and 'dapm->card' yield the same result.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The accessory detect debounce work is not performance sensitive so let
the scheduler run it wherever is most efficient rather than in a per CPU
workqueue by using the system power efficient workqueue.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
There is no need to use a normal per-CPU workqueue for delayed power downs
as they're not timing or performance critical and waking up a core for them
would defeat some of the point.
Signed-off-by: Mark Brown <broonie@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
We've got bug reports that the module loading stuck on Debian system
with 3.10 kernel. The debugging session revealed that the initial
registration of OSS sequencer clients stuck at module loading time,
which involves again with request_module() at the init phase. This is
triggered only by special --install stuff Debian is using, but it's
still not good to have such loops.
As a workaround, call the registration part asynchronously. This is a
better approach irrespective of the hang fix, in anyway.
Reported-and-tested-by: Philipp Matthias Hahn <pmhahn@pmhahn.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Vendor ID 0x10de0060 is used by a yet-to-be-named GPU chip.
Reviewed-by: Andy Ritger <aritger@nvidia.com>
Signed-off-by: Aaron Plattner <aplattner@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_pcm_stop() must be called in the PCM substream lock context.
Cc: <stable@vger.kernel.org>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_pcm_stop() must be called in the PCM substream lock context.
Cc: <stable@vger.kernel.org>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_pcm_stop() must be called in the PCM substream lock context.
Cc: <stable@vger.kernel.org>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_pcm_stop() must be called in the PCM substream lock context.
Cc: <stable@vger.kernel.org>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The biggest change here is the OMAP change, these are larger than I'd
have liked but make the driver actually usable - during the merge window
OMAP removed support for non-DT OMAP4 boards but in doing so removed the
method of accessing DMA channels used by the ASoC drivers rendering them
unusuable.
Otherwise nothing exciting, the symmetric rates change for WM8978 is a
fix for the information we expose to userspace.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Juij
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v3.11
The biggest change here is the OMAP change, these are larger than I'd
have liked but make the driver actually usable - during the merge window
OMAP removed support for non-DT OMAP4 boards but in doing so removed the
method of accessing DMA channels used by the ASoC drivers rendering them
unusuable.
Otherwise nothing exciting, the symmetric rates change for WM8978 is a
fix for the information we expose to userspace.
The main function of the option is to enable compile testing. There is
still an option since COMPILE_TEST is intended to enable selection of
extra drivers rather than forcing them on.
Signed-off-by: Mark Brown <broonie@kernel.org>
While the conversion of BKL to mutex in commit 645ef9ef, the mutex
definition was put in a wrong place inside #ifdef WSND_DEBUG, which
leads to the build error. Just move it outside the ifdef.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is our first set of fixes from arm-soc for 3.11.
- A handful of build and warning fixes from Arnd
- A collection of OMAP fixes
- defconfig updates to make the default configs more useful for real use
(and testing) out of the box on hardware.
And a couple of other small fixes. Some of these have been recently
applied but it's normally how we deal with fixes, with less bake time
in -next needed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=fKfy
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"This is our first set of fixes from arm-soc for 3.11.
- A handful of build and warning fixes from Arnd
- A collection of OMAP fixes
- defconfig updates to make the default configs more useful for real
use (and testing) out of the box on hardware
And a couple of other small fixes. Some of these have been recently
applied but it's normally how we deal with fixes, with less bake time
in -next needed"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (32 commits)
arm: multi_v7_defconfig: Tweaks for omap and sunxi
arm: multi_v7_defconfig: add i.MX options and NFS root
ARM: omap2: add select of TI_PRIV_EDMA
ARM: exynos: select PM_GENERIC_DOMAINS only when used
ARM: ixp4xx: avoid circular header dependency
ARM: OMAP: omap_common_late_init may be unused
ARM: sti: move DEBUG_STI_UART into alphabetical order
ARM: OMAP: build mach-omap code only if needed
ARM: zynq: use DT_MACHINE_START
ARM: omap5: omap5 has SCU and TWD
ARM: OMAP2+: omap2plus_defconfig: Enable appended DTB support
ARM: OMAP2+: Enable TI_EDMA in omap2plus_defconfig
ARM: OMAP2+: omap2plus_defconfig: enable DRA752 thermal support by default
ARM: OMAP2+: omap2plus_defconfig: enable TI bandgap driver
ARM: OMAP2+: devices: remove duplicated include from devices.c
ARM: OMAP3: igep0020: Set DSS pins in correct mux mode.
ARM: OMAP2+: N900: enable N900-specific drivers even if device tree is enabled
ARM: OMAP2+: Cocci spatch "ptr_ret.spatch"
ARM: OMAP2+: Remove obsolete Makefile line
ARM: OMAP5: Enable Cortex A15 errata 798181
...
wm8978 needs .symmetric_rates = 1.
The playback/capture will be strange without this patch
when it used asymmetric rate in same time
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The DMA resource no longer available via this API when booting with DT.
When the board is booted with DT do not use platform_get_resource_byname(),
instead set the dma_data.filter_data to the name of the DMA channel and omap-pcm
can use this name to request the DMA channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The DMA resource no longer available via this API when booting with DT.
DMIC is only available on OMAP4/5 and both can boot with DT only.
Set the dma_data.filter_data to the DMA name which will be used by omap-pcm
to request the DMA channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The DMA resource no longer available via this API when booting with DT.
McPDM is only available on OMAP4/5 and both can boot with DT only.
Set the dma_data.filter_data to the DMA name which will be used by omap-pcm
to request the DMA channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
When booting with DT the platform_get_resource_byname() is not available to
get the DMA resource. In this case the DAI drivers will set the filter_data to
the name of the DMA and omap-pcm can use this to request the DMA channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
As per the User Manual, the RFS and BFS should be set in slave mode
for correct operation.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Simon Glass <sjg@google.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make struct ieee1394_device_id.driver_data actually avaliable to
1394 protocol drivers. This is especially useful to 1394 audio drivers
for model-specific parameters and methods.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.20 (GNU/Linux)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=8MqX
-----END PGP SIGNATURE-----
Merge tag 'firewire-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull firewire updates from Stefan Richter:
"Make struct ieee1394_device_id.driver_data actually avaliable to 1394
protocol drivers. This is especially useful to 1394 audio drivers for
model-specific parameters and methods"
* tag 'firewire-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: remove support of fw_driver.driver.probe and .remove methods
firewire: introduce fw_driver.probe and .remove methods
Commit 8f898e92ae removed the redundant
reads of bInterfaceProtocol from the descriptors, but introduced a
regression to devices with quirks of type QUIRK_AUDIO_FIXED_ENDPOINT,
since fp->protocol is not set in setup process.
As a consequence, audio streams would not get initialized, as the
following logs show:
[ 48.923043] setting usb interface 3:1
[ 48.923056] Creating new capture data endpoint #81
[ 48.923484] 4:3:1: cannot set freq 48000 to ep 0x81
This patch sets fp->protocol in create_fixed_stream_quirk() and
resolves the regression.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull drm updates from Dave Airlie:
"Okay this is the big one, I was stalled on the fbdev pull req as I
stupidly let fbdev guys merge a patch I required to fix a warning with
some patches I had, they ended up merging the patch from the wrong
place, but the warning should be fixed. In future I'll just take the
patch myself!
Outside drm:
There are some snd changes for the HDMI audio interactions on haswell,
they've been acked for inclusion via my tree. This relies on the
wound/wait tree from Ingo which is already merged.
Major changes:
AMD finally released the dynamic power management code for all their
GPUs from r600->present day, this is great, off by default for now but
also a huge amount of code, in fact it is most of this pull request.
Since it landed there has been a lot of community testing and Alex has
sent a lot of fixes for any bugs found so far. I suspect radeon might
now be the biggest kernel driver ever :-P p.s. radeon.dpm=1 to enable
dynamic powermanagement for anyone.
New drivers:
Renesas r-car display unit.
Other highlights:
- core: GEM CMA prime support, use new w/w mutexs for TTM
reservations, cursor hotspot, doc updates
- dvo chips: chrontel 7010B support
- i915: Haswell (fbc, ips, vecs, watermarks, audio powerwell),
Valleyview (enabled by default, rc6), lots of pll reworking, 30bpp
support (this time for sure)
- nouveau: async buffer object deletion, context/register init
updates, kernel vp2 engine support, GF117 support, GK110 accel
support (with external nvidia ucode), context cleanups.
- exynos: memory leak fixes, Add S3C64XX SoC series support, device
tree updates, common clock framework support,
- qxl: cursor hotspot support, multi-monitor support, suspend/resume
support
- mgag200: hw cursor support, g200 mode limiting
- shmobile: prime support
- tegra: fixes mostly
I've been banging on this quite a lot due to the size of it, and it
seems to okay on everything I've tested it on."
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (811 commits)
drm/radeon/dpm: implement vblank_too_short callback for si
drm/radeon/dpm: implement vblank_too_short callback for cayman
drm/radeon/dpm: implement vblank_too_short callback for btc
drm/radeon/dpm: implement vblank_too_short callback for evergreen
drm/radeon/dpm: implement vblank_too_short callback for 7xx
drm/radeon/dpm: add checks against vblank time
drm/radeon/dpm: add helper to calculate vblank time
drm/radeon: remove stray line in old pm code
drm/radeon/dpm: fix display_gap programming on rv7xx
drm/nvc0/gr: fix gpc firmware regression
drm/nouveau: fix minor thinko causing bo moves to not be async on kepler
drm/radeon/dpm: implement force performance level for TN
drm/radeon/dpm: implement force performance level for ON/LN
drm/radeon/dpm: implement force performance level for SI
drm/radeon/dpm: implement force performance level for cayman
drm/radeon/dpm: implement force performance levels for 7xx/eg/btc
drm/radeon/dpm: add infrastructure to force performance levels
drm/radeon: fix surface setup on r1xx
drm/radeon: add support for 3d perf states on older asics
drm/radeon: set default clocks for SI when DPM is disabled
...
ALC5505 DSP is enabled even though we don't use the features yet at
all. This results in the unnecessarily high power consumption, more
than 100mV higher. Until we implement the DSP support, better to
bypass DSP for saving more power.
Reported-by: Mengdong Lin <mengdong.lin@intel.com>
[Patch modified by Mengdong to cal alc5505_dsp_init() with extra
acl5505_dsp_halt().]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few small fixes, all driver specific. The removal of the GPIO based
pinmuxing is a bug fix, since the obsolete nodes had been removed from
the DT it stopped the driver loading.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=+rVP
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.11-4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v3.11
A few small fixes, all driver specific. The removal of the GPIO based
pinmuxing is a bug fix, since the obsolete nodes had been removed from
the DT it stopped the driver loading.
SGTL5000_PLL_FRAC_DIV_MASK is used to mask bits 0-10 (11 bits in total) of
register CHIP_PLL_CTRL, so fix the mask to accomodate all this bit range.
Reported-by: Oskar Schirmer <oskar@scara.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
According to the sgtl5000 reference manual, the default value of CHIP_SSS_CTRL
is 0x10.
Reported-by: Oskar Schirmer <oskar@scara.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Pull trivial tree updates from Jiri Kosina:
"The usual stuff from trivial tree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
treewide: relase -> release
Documentation/cgroups/memory.txt: fix stat file documentation
sysctl/net.txt: delete reference to obsolete 2.4.x kernel
spinlock_api_smp.h: fix preprocessor comments
treewide: Fix typo in printk
doc: device tree: clarify stuff in usage-model.txt.
open firmware: "/aliasas" -> "/aliases"
md: bcache: Fixed a typo with the word 'arithmetic'
irq/generic-chip: fix a few kernel-doc entries
frv: Convert use of typedef ctl_table to struct ctl_table
sgi: xpc: Convert use of typedef ctl_table to struct ctl_table
doc: clk: Fix incorrect wording
Documentation/arm/IXP4xx fix a typo
Documentation/networking/ieee802154 fix a typo
Documentation/DocBook/media/v4l fix a typo
Documentation/video4linux/si476x.txt fix a typo
Documentation/virtual/kvm/api.txt fix a typo
Documentation/early-userspace/README fix a typo
Documentation/video4linux/soc-camera.txt fix a typo
lguest: fix CONFIG_PAE -> CONFIG_x86_PAE in comment
...
Lars-Peter Clausen