Nominally an autoconfigured IPv6 address is added to an interface in the
Tentative state (as per RFC 2462). Addresses in this state remain in this
state while the Duplicate Address Detection process operates on them to
determine their uniqueness on the network. During this period, these
tentative addresses may not be used for communication, increasing the time
before a node may be able to communicate on a network. Using Optimistic
Duplicate Address Detection, autoconfigured addresses may be used
immediately for communication on the network, as long as certain rules are
followed to avoid conflicts with other nodes during the Duplicate Address
Detection process.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I tested IPv6 redirect function about kernel 2.6.19.1, and found
that the kernel can send redirect packets whose target address is global
address, and the target is not the actual endpoint of communication.
But the criteria conform to RFC2461, the target address defines as
following:
Target Address An IP address that is a better first hop to use for
he ICMP Destination Address. When the target is
the actual endpoint of communication, i.e., the
destination is a neighbor, the Target Address field
MUST contain the same value as the ICMP Destination
Address field. Otherwise the target is a better
first-hop router and the Target Address MUST be the
router's link-local address so that hosts can
uniquely identify routers.
According to this definition, when a router redirect to a host, the
target address either the better first-hop router's link-local address
or the same as the ICMP destination address field. But the function of
ndisc_send_redirect() in net/ipv6/ndisc.c, does not check the target
address correctly.
There is another definition about receive Redirect message in RFC2461:
8.1. Validation of Redirect Messages
A host MUST silently discard any received Redirect message that does
not satisfy all of the following validity checks:
......
- The ICMP Target Address is either a link-local address (when
redirected to a router) or the same as the ICMP Destination
Address (when redirected to the on-link destination).
......
And the receive redirect function of ndisc_redirect_rcv() implemented
this definition, checks the target address correctly.
if (ipv6_addr_equal(dest, target)) {
on_link = 1;
} else if (!(ipv6_addr_type(target) & IPV6_ADDR_LINKLOCAL)) {
ND_PRINTK2(KERN_WARNING
"ICMPv6 Redirect: target address is not link-local.\n");
return;
}
So, I think the send redirect function must check the target address
also.
Signed-off-by: Li Yewang <lyw@nanjing-fnst.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAX_HEADER does not include the ipv6 header length in it,
so we need to add it in explicitly.
With help from YOSHIFUJI Hideaki.
Signed-off-by: David S. Miller <davem@davemloft.net>
If inet6_init() fails later than ndisc_init() call, or IPv6 module is
unloaded, ndisc_netdev_notifier call remains in the list and will follows in
oops later.
Signed-off-by: Dmitry Mishin <dim@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We did not send appropriate IsRouter flag if the forwarding setting is
positive even value. Let's give 1/0 value to ndisc_send_na().
Also, existing users of ndisc_send_na() give 0/1 to override,
we can omit redundant operation in that function.
Bug hinted by Nicolas Dichtel <nicolas.dichtel@6wind.com>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We do not always need proxy NDP functionality even we
enable forwarding.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have sent NA with router flag from the node-wide forwarding
configuration. This is not appropriate for proxy NA, and it should be
set according to each proxy entry's configuration.
This is used by Mobile IPv6 home agent to support physical home link
in acting as a proxy router for mobile node which is not a router,
for example.
Based on MIPL2 kernel patch.
Signed-off-by: Ville Nuorvala <vnuorval@tcs.hut.fi>
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
This aims at proxying router not updating neighbor cache entry for proxied
address when it receives NA because either the proxied node is off link or
it has already sent a NA to the proxied router.
Based on MIPL2 kernel patch.
Signed-off-by: Ville Nuorvala <vnuorval@tcs.hut.fi>
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Based on MIPL2 kernel patch.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Ville Nuorvala <vnuorval@tcs.hut.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Ville Nuorvala <vnuorval@tcs.hut.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide a simple ip6_del_rt() for the majority of users and
an alternative for the exception via netlink. Avoids code
obfuscation.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This labels the flows that could utilize IPSec xfrms at the points the
flows are defined so that IPSec policy and SAs at the right label can
be used.
The following protos are currently not handled, but they should
continue to be able to use single-labeled IPSec like they currently
do.
ipmr
ip_gre
ipip
igmp
sit
sctp
ip6_tunnel (IPv6 over IPv6 tunnel device)
decnet
Signed-off-by: Venkat Yekkirala <vyekkirala@TrustedCS.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This controls whether we accept Prefix Information in RAs.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This controls whether we accept default router information
in RAs.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are errors and inconsistency in the display of NIP6 strings.
ie: net/ipv6/ip6_flowlabel.c
There are errors and inconsistency in the display of NIPQUAD strings too.
ie: net/netfilter/nf_conntrack_ftp.c
This patch:
adds NIP6_FMT to kernel.h
changes all code to use NIP6_FMT
fixes net/ipv6/ip6_flowlabel.c
adds NIPQUAD_FMT to kernel.h
fixes net/netfilter/nf_conntrack_ftp.c
changes a few uses of "%u.%u.%u.%u" to NIPQUAD_FMT for symmetry to NIP6_FMT
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Timer set up by pneigh_enqueue() ended up calling ndisc_rcv()
via pndisc_redo(), which clears LOCALLY_ENQUEUED flag in
NEIGH_CB(skb) and NS was queued again.
Let's call ndisc_recv_ns() directly to avoid the loop.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Essentially netlink at the moment always reports a pid and sequence of 0
always for v6 route activities.
To understand the repurcassions of this look at:
http://lists.quagga.net/pipermail/quagga-dev/2005-June/003507.html
While fixing this, i took the liberty to resolve the outstanding issue
of IPV6 routes inserted via ioctls to have the correct pids as well.
This patch tries to behave as close as possible to the v4 routes i.e
maintains whatever PID the socket issuing the command owns as opposed to
the process. That made the patch a little bulky.
I have tested against both netlink derived utility to add/del routes as
well as ioctl derived one. The Quagga folks have tested against quagga.
This fixes the problem and so far hasnt been detected to introduce any
new issues.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Neil Horman