So far we depended on the HW to dynamically power down unused PHYs and
so we enabled them manually once during driver loading/resuming. There
are indications however that we can achieve better power savings by
manual powering toggling. So make the PHY enabling/disabling to happen
on-demand whenever we need either the corresponding AUX or port
functionality. CHV does this already by enabling the PHY along the
corresponding PHY common lane power wells there, do the same on BXT by
adding virtual power wells for the same purpose.
Also sanity check the common lane power down ack signal from the PHY. Do
this only when the PHY is enabled, since it's not clear at what point
the HW power/clock gates things.
While at it rename broxton_ prefix to bxt_ in related function names to
better align with the SKL code.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
These helpers will be needed by the next patch, so factor them out.
No functional change.
v2:
- Move the refcount==0 WARN to the new put helper. (Ville)
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Like with cdclk, the DMC is supposed to manage dbuf enabling/disabling.
Let's make sure it has correctly restored the dbuf state to enabled
when we disable the DC states.
v2: s/skl/gen9/ in function name (Imre)
Cc: Imre Deak <imre.deak@intel.com>
Suggested-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463407180-28993-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Rather than having a BXT specific function to make sure the DE PLL is
enabled after disabling DC6, let's just make sure the current cdclk
is the same as what we last programmed.
Having another check in bxt_display_core_init() almost immediately after
the cdclk init seems redundant, so let's just kill that one.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-21-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
SKL and BXT have the same snippets of code for enabling disabling the
DBUF. Extract those into helpers and move the calls from
init/unit_cdclk() to the display core init/init since this stuff isn't
really about cdclk. Also doing the enable twice shouldn't hurt since
you're just setting the request bit again when it was already set.
We can also toss in a few WARNs about the register values into
skl_get_dpll0_vco() now that we know that things should always be
sane there.
Flatten skl_init_cdclk() while at it.
v2: s/skl/gen9/ in function names (Imre)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-12-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Currently we initialize cdclk on SKL from two different places,
depending on whether it's during driver init or resume. Let's
unify it to happen from the same place always, and that place will be
the display core init function.
To do this we first run through the cdclk sanitation code, which will
first verify that the PLL is programmed correctly, after which we can
read out the current cdclk frequency, and once the cdclk is known we
verify that the cdclk "decimal" frequency is programmed correctly. If
any of these fail we will force a cdclk change, and to be safe we also
force the PLL to be turned off and on again. If the sanitation step
didn't notice anything amiss, we'll skip the cdclk programming which
will prevent cdclk reprogramming when the displays might be active.
We can also toss in a few WARNs about the register values into
skl_update_dpll0() since we now know that the PLL state should
always be sane when that function is called.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-11-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
I just noticed that VLV/CHV have a RAWCLK_FREQ register just like PCH
platforms. It lives in the display power well, so we should update it
when enabling the power well.
Interestingly the BIOS seems to leave it at the reset value (125) which
doesn't match the rawclk frequency on VLV/CHV (200 MHz). As always with
these register, the spec is extremely vague what the register does. All
it says is: "This is used to generate a divided down clock for
miscellaneous timers in display." Based on a quick test, at least AUX
and PWM appear to be unaffected by this.
But since the register is there, let's configure it in accordance with
the spec.
Note that we have to move intel_update_rawclk() to occur before we
touch the power wells, so that the dev_priv->rawclk_freq is already
populated when the disp2 enable hook gets called for the first time.
I think this should be safe to do on other platforms as well.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461768202-17544-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Right after runtime resume we know that we can re-enable DC5, since we
just disabled DC9 and power well 2 is disabled. So enable DC5 explicitly
instead of delaying this until the next time we disable power well 2.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Bob Paauwe <bob.j.paauwe@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461173277-16090-5-git-send-email-imre.deak@intel.com
After suspend-to-ram or -disk we don't know what power state the display
HW will be, DC0 or DC9 are both possible states, so reset the software
DC state tracking in these cases. This gets rid of 'DC state mismatch'
error messages during resuming from ram or disk where we expected to be
in DC9 (as set by the suspend handler) but we are in DC0.
v2:
- Remove extra WS in gen9_sanitize_dc_state() (Bob)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Bob Paauwe <bob.j.paauwe@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461173277-16090-4-git-send-email-imre.deak@intel.com
In commit 5f304c8736 ("drm/i915/kbl: Reset secondary power well requests
left on by DMC/KVMR") I forgot about the fact that SKL==KBL most of the
time and that a secondary MISC IO power well request left on by the DMC is
"expected". Tune down the corresponding WARN to be a debug message. This
was caught by CI suspend tests.
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461060036-19043-1-git-send-email-imre.deak@intel.com
Currently we're trying to define HSW/BDW power wells by what's not
included. Let's do it the other way around, so that you can actually
tell when the power well would get enabled. This will also allow us to
add new power domains without accidentally adding it to the HSW/BDW
display power domains.
The current set of domains looks rather buggy even:
- POWER_DOMAIN_MODESET is included in the display power well needlessly
- DDI-B to DDI-E were not part of the display power well when they
should be
So let's fix that up while at it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460977348-32260-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Currently we're using POWER_DOMAIN_MASK as the power domains for the
display power well on VLV/CHV. That includes all power domains even
though the disp2d/pipe-a power well is not needed for a lot of things.
Let's reduce these to what we actually need.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460977348-32260-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
While we disable runtime PM and with that display power well support if
the DMC firmware isn't loaded, we still want to disable power wells
during system suspend and driver unload. So drop/reacquire the
corresponding power refcount during suspend/resume and driver unloading.
This also means we have to check if DMC is not loaded and skip enabling
DC states in the power well code.
v2:
- Reuse intel_csr_ucode_suspend() in intel_csr_ucode_fini() instead of
opencoding the former. (Chris)
- Add docbook comment to the public resume and suspend functions.
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1460980101-14713-1-git-send-email-imre.deak@intel.com
The workaround added in
commit c6782b76d3 ("drm/i915/gen9: Reset secondary power well
requests left on by DMC/KVMR")
needs to be applied on Kabylake too as shown by the corresponding
timeout errors about power well 1 and MISC IO power well disabling in
the latest CI run.
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460748778-4484-1-git-send-email-imre.deak@intel.com
I caught a few errors in our current PHY/CDCLK programming by sanity
checking the actual programmed state, so I thought it would be also
useful for the future. In addition to verifying the state after
programming it also verify it after exiting DC5, to make sure DMC
restored/kept intact everything related.
v2:
- Inlining __phy_reg_verify_state() doesn't make sense and also
incorrect, so don't do it (PW/CI gcc)
v3:
- Rebase on latest -nightly
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: David Weinehall <david.weinehall@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459780030-15781-1-git-send-email-imre.deak@intel.com
Power well 1 is managed by the DMC firmware so don't toggle it on-demand
from the driver. This means we need to follow the BSpec display
initialization sequence during driver loading and resuming (both system
and runtime) and enable power well 1 only once there. Afterwards DMC
will toggle power well 1 whenever entering/exiting DC5.
For this to work we also need to do away getting the PLL power domain,
since that just kept runtime PM disabled for good.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-12-git-send-email-imre.deak@intel.com
On Broxton we need to enable/disable power well 1 during the init/unit
display sequence similarly to Skylake/Kabylake. The code for this will
be added in a follow-up patch, but to prepare for that unexport
skl_pw1_misc_io_init(). It's a simple function called only from a single
place and having it inlined in the Skylake display core init/unit
functions will make it easier to compare it with its Broxton
counterpart.
This also flips the order of Misc IO and power well 1 disabling which
matches the enabling order. The specification doesn't prescribe the
disabling order, so this should be fine.
v2:
- Fix incorrect enable vs. disable power well call in
skl_display_core_uninit() (Patrik)
- Add commit comment about chaning the order of PW1 and Misc IO power
well disabling (Patrik)
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459773777-10701-1-git-send-email-imre.deak@intel.com
The display power well support and DC state management doesn't depend on
runtime PM support, so remove the incorrect asserts about this.
Also Broxton does support DC5, so the related assert in
assert_can_enable_dc5() is incorrect. There is a more generic and
correct assert for this already in gen9_set_dc_state(), so we can remove
all the other ones.
At the same time convert WARNs to WARN_ONCE for consistency with the
other DC state asserts.
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-7-git-send-email-imre.deak@intel.com
So far we only power well enabling was synchronous not disabling. Since
we don't exactly know how the firmware (both DMC and PCU) synchronizes
against the actual power well state during DC transitions, make the
disabling also synchronous.
CC: Mika Kuoppala <mika.kuoppala@linux.intel.com>
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-6-git-send-email-imre.deak@intel.com
DMC forces on power well 1 and the misc IO power well by setting the
corresponding request bits both in the BIOS and the DEBUG power well
request registers. This is somewhat unexpected since the firmware should
really just save and restore state but not alter it. We also depend on
being able to disable power well 1, and the misc IO power well before
entering S3/S4 on BXT and SKL or entering DC9 on BXT. To fix this make
sure these request bits are cleared whenever we want to disable the
given power wells.
On SKL there is another twist where the firmware also clears the power
well 1 request bit in HSW_POWER_WELL_DRIVER (but not that of the misc IO
power well). This happens to not cause a problem due to the forced-on
request bits in the other request registers.
I've filed a bug about all this, but fixing that may take a while and
having this sanity check in place makes sense even for future firmware
versions.
At the same time also check the KVMR request bits. I haven't seen this
being altered, but we don't expect any request bits in here either, so
sanitize this register as well.
v2:
- Apply the workaround on SKL as well. I noticed the related failure
from the CI report, later Patrik also reported seeing it on his
machine.
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459851965-6137-1-git-send-email-imre.deak@intel.com
The registers frobbed by vlv_init_display_clock_gating() libve inside
the disp2d power well, so frobbing them while the power well is down
results in unclaimed register access warning (and of course the values
won't stick). Let's do this setup after we know the power well is
enabled.
It's also worth noting that DSPCLK_GATE_D and CBR1_VLV lose their state
when the power well goes down, but fortunately the values we've been
writing are actually the reset defaults.
MI_ARB_VLV actually retains its value even if the power well was turned
off, we just can't access it while the power well is down.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94164
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460382992-28728-9-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
dev_priv is what the macro works hard to extract, pass it directly.
> sed 's/\([A-Z].*(dev_priv\)->dev)/\1)/g'
v2:
- Include all wrapper macros too (Chris)
v3:
- Include sed cmdline (Chris)
v4:
- Break long line
- Rebase
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460016485-8089-1-git-send-email-joonas.lahtinen@linux.intel.com
The BXT display connections have DSI transcoders A and C that can be
muxed to any pipe, not unlike the eDP transcoder. Add the notion of DSI
transcoders.
The "normal" transcoders A, B and C are not used with BXT DSI, so care
must be taken to avoid accessing those registers with DSI transcoders in
the hardware state readout, modeset, and generally everywhere.
v2: addressing comments by Ville:
- rename the dsi get config function to hsw_get_dsi_transcoder_state
- rebase onto the higher level split of pipe/transcoder functions
- use more has_dsi_encoder as we can now because of the above,
with no need to look at the transcoder so much
- rename IS_DSI_TRANSCODER to transcoder_is_dsi
- use the above a bit more instead of comparing to < TRANSCODER_EDP
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/299740536b7941e31b2744f3ce34f7afe936a771.1458313400.git.jani.nikula@intel.com
The DSI power domain was missing from BXT power well 1 definitions,
failing to get the power well for DSI transcoders. As pipe A is in the
same power well as DSI transcoders, the problem should only occur with
pipes B and C.
According to Ville, this is basically a nop since pw1 is under dmc
control. But given that we still have this stuff defined here, it's
clearly correct to include DSI here.
Cc: Ramalingam C <ramalingam.c@intel.com>
Cc: Deepak M <m.deepak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457463656-29357-1-git-send-email-jani.nikula@intel.com
In commit 1e657ad7 we moved the last step of firmware initialization to
skl_display_core_init(), where it will be run only during system resume,
but not during driver loading. Since this init step needs to be done
whenever we program the firmware fix this by moving the initialization
to the end of intel_csr_load_program().
While at it simplify a bit csr_load_work_fn().
This issue prevented DC5/6 transitions, this change will re-enable those.
v2:
- remove debugging left-over and redundant comment in csr_load_work_fn()
Fixes: 1e657ad7a4 ("drm/i915/gen9: Write dc state debugmask bits only once")
CC: Mika Kuoppala <mika.kuoppala@intel.com>
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457121461-16729-1-git-send-email-imre.deak@intel.com
Disabling the DC states when it's already disabled is a valid scenario,
for example during HW state sanitization during driver loading and
resuming or when DC states are disabled via the i915.enable_dc or
disable_power_well option.
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1456778945-5411-4-git-send-email-imre.deak@intel.com
If power well support is disabled via the i915.disable_power_well module
option we should never enable DC states. Currently we would enable DC
states even in this case during system suspend, where we need to disable
all power wells regardless of the disable_power_well option.
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1456778945-5411-3-git-send-email-imre.deak@intel.com
We can simplify the conditions selecting the target DC state during
runtime by calculating the allowed DC states in advance during driver
loading. This also makes it easier to disable DC states depending on the
i915.disable_power_well module option, added in the next patch.
v2:
- Print a debug message if the requested max DC value was adjusted due
to a platform limit. Also debug print the calculated mask value. (Patrik)
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1456778945-5411-2-git-send-email-imre.deak@intel.com
During system suspend we need to first disable power wells then
unitialize the display core. In case power well support is disabled we
did this in the wrong order, so fix this up.
Fixes: d314cd43 ("drm/i915: fix handling of the disable_power_well module option")
CC: stable@vger.kernel.org
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1456778945-5411-1-git-send-email-imre.deak@intel.com
commit 0973128002
Author: Imre Deak <imre.deak@intel.com>
Date: Wed Feb 17 14:17:42 2016 +0200
drm/i915: Add helper to get a display power ref if it was already enabled
left the rpm wakelock assertions unbalanced if CONFIG_PM was disabled as
intel_runtime_pm_get_if_in_use() would return true without incrementing
the local bookkeeping required for the assertions.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
CC: Mika Kuoppala <mika.kuoppala@intel.com>
CC: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1456434628-22574-1-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Imre Deak <imre.deak@intel.com>
Starting from BDW the DE_PIPE interrupts for pipe B and C belong to the
relevant display power well. So we should make sure we've finished
processing them before turning off the power well.
The pipe interrupts shouldn't really happen at this point anymore since
we've already shut down the planes/pipes/whatnot, but being a bit
paranoid shouldn't hurt.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455907651-16397-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
After we've told the irq code we don't want to handle display irqs
anymore, we must make sure any display irq handling already
kicked off has finished before we actually turn off the power well.
I wouldn't expect PIPESTAT based interrupts to occur anymore since
vblanks/page flips/gmbus/etc should all be quiescent at this point.
But at least hotplug interrupts could still occur. Hotplug
interrupts may also kick off the workqueue based hotplug processing,
but that code should take the required power domain references
itself, so there shouldn't be any need to synchronize with the
hotplug processing from the power well code.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455900112-15387-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Cores need to be included into the debug mask. We don't exactly
know what it does but the spec says it must be enabled. So obey.
v2: Cores should be only set for BXT (Imre, Art)
Cc: Imre Deak <imre.deak@intel.com>
Cc: Runyan, Arthur J <arthur.j.runyan@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455877564-5128-1-git-send-email-mika.kuoppala@intel.com
It has been observed that sometimes disabling the dc6 fails
and dc6 state pops back up, brief moment after disabling. This
has to be dmc save/restore timing issue or other bug in the
way dc states are handled.
Try to work around this issue as we don't have firmware fix
yet available. Verify that the value we wrote for the dmc sticks,
and also enforce it by rewriting it, if it didn't.
v2: Zero rereads on rewrite for extra paranoia (Imre)
Testcase: kms_flip/basic-flip-vs-dpms
References: https://bugs.freedesktop.org/show_bug.cgi?id=93768
Cc: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455811089-27884-1-git-send-email-mika.kuoppala@intel.com
The DMC can incorrectly run off and allow DC states on it's own. We
don't know the root-cause for this yet but this patch makes it more
visible.
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455808874-22089-2-git-send-email-mika.kuoppala@intel.com
We have many places in the code where we check if a given display power
domain is enabled and if so access registers backed by this power
domain. We assumed that some modeset lock will prevent the power
reference from vanishing in the middle of the HW access, but this
assumption doesn't always hold. In such cases we get either the wakeref
not held, or an unclaimed register access error message. To fix this in
a future-proof way that's independent of other locks wrap any such
access with a get_ref_if_enabled()/put_ref() pair.
Kudos to Ville and Joonas for the ideas of this new interface.
v2:
- init the power_domains ptr when declaring it everywhere (Joonas)
v3:
- don't report the device to be powered if runtime PM is disabled
CC: Mika Kuoppala <mika.kuoppala@intel.com>
CC: Chris Wilson <chris@chris-wilson.co.uk>
CC: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455711462-7442-1-git-send-email-imre.deak@intel.com
Move the ddi buffer translation programming to occur from the encoder
.pre_enable() hook, for just the ddi port we are enabling. Previously
we used to reprogram the translations for all ddi ports during
init and during power well enabling.
v2: s/intel_prepare_ddi_buffers/intel_prepare_ddi_buffer/ (Daniel)
Resolve conflicts due to dev_priv->atomic_cdclk_freq
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When adding IS_KABYLAKE definition I didn't included the
DC states related because I was planing to include them
with the patch that fixes DMC firmware loading, but I
forgot them.
Meanwhile this runtime pm code changed a lot for
Skylake.
Well, I didn't expect that this would crash the machine
and I just noticed now that Sarah warned me our driver
wasn't working. Thanks Sarah.
Michel had found the main error first and his
fix had better details on the history and got
merged already:
commit 16fbc291cb
Author: Michel Thierry <michel.thierry@intel.com>
Date: Wed Jan 6 12:08:36 2016 +0000
drm/i915/kbl: Enable PW1 and Misc I/O power wells
This one is a follow-up adding the other remaining
missing pieces.
v2: Rebased on top of Michel's patch as explained above.
Cc: Sarah Sharp <sarah.a.sharp@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452214179-22361-1-git-send-email-rodrigo.vivi@intel.com
My kbl stopped working because of this.
Fixes regression from
commit 2f693e28b8
Author: Damien Lespiau <damien.lespiau@intel.com>
Date: Wed Nov 4 19:24:12 2015 +0200
drm/i915: Make turning on/off PW1 and Misc I/O part of the init/fini
sequences
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452082116-16770-1-git-send-email-michel.thierry@intel.com
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
pm_runtime_{use,dont_use}_autosuspend() controls whether the device's
sysfs power/autosuspend_delay_ms file is writeable or returns -EIO on
access to user space. Since
commit 25b181b46e
Author: Imre Deak <imre.deak@intel.com>
Date: Thu Dec 17 13:44:56 2015 +0200
drm/i915: get a permanent RPM reference on platforms w/o RPM support
this sysfs file is writeable also on platforms without RPM support, but
userspace (at least IGT) depends on this file being unchangable to
determine whether the device supports runtime PM at all. So restore the
old behavior.
This gets rid of igt/pm_rpm failures on old platforms without RPM
support, where the test should be skipped.
Testcase: igt/pm_rpm/basic-rte
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: David Weinehall <david.weinehall@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450371873-878-1-git-send-email-imre.deak@intel.com
In some cases we want to check whether we hold an RPM wakelock reference
for the whole duration of a sequence. To achieve this add a new RPM
atomic sequence counter that we increment any time the wakelock refcount
drops to zero. Check whether the sequence number stays the same during
the atomic section and that we hold the wakelock at the beginning of the
section.
Motivated by Chris.
v2-v3:
- unchanged
v4:
- swap the order of atomic_read() and assert_rpm_wakelock_held() in
assert_rpm_atomic_begin() to avoid race
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v3)
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450203038-5150-10-git-send-email-imre.deak@intel.com
With this change we have the corresponding wake lock checks in both the
rpm get and put functions.
v2-v3:
- unchanged
v4:
- keep the corresponding check in the get helper (Chris)
v5:
- add a note to the commit message that with this change we have the
checks both in the rpm get and put functions (Joonas)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450203038-5150-9-git-send-email-imre.deak@intel.com
Atm, we assert that the device is not suspended until the point when the
device is truly put to a suspended state. This is fine, but we can catch
more problems if we check that RPM refcount is non-zero. After that one
drops to zero we shouldn't access the device any more, even if the actual
device suspend may be delayed. Change assert_rpm_wakelock_held()
accordingly to check for a non-zero RPM refcount in addition to the
current device-not-suspended check.
For the new asserts to work we need to annotate every place explicitly in
the code where we expect that the device is powered. The places where we
only assume this, but may not hold an RPM reference:
- driver load
We assume the device to be powered until we enable RPM. Make this
explicit by taking an RPM reference around the load function.
- system and runtime sudpend/resume handlers
These handlers are called when the RPM reference becomes 0 and know the
exact point after which the device can get powered off. Disable the
RPM-reference-held check for their duration.
- the IRQ, hangcheck and RPS work handlers
These handlers are flushed in the system/runtime suspend handler
before the device is powered off, so it's guaranteed that they won't
run while the device is powered off even though they don't hold any
RPM reference. Disable the RPM-reference-held check for their duration.
In all these cases we still check that the device is not suspended.
These explicit annotations also have the positive side effect of
documenting our assumptions better.
This caught additional WARNs from the atomic modeset path, those should
be fixed separately.
v2:
- remove the redundant HAS_RUNTIME_PM check (moved to patch 1) (Ville)
v3:
- use a new dedicated RPM wakelock refcount to also catch cases where
our own RPM get/put functions were not called (Chris)
- assert also that the new RPM wakelock refcount is 0 in the RPM
suspend handler (Chris)
- change the assert error message to be more meaningful (Chris)
- prevent false assert errors and check that the RPM wakelock is 0 in
the RPM resume handler too
- prevent false assert errors in the hangcheck work too
- add a device not suspended assert check to the hangcheck work
v4:
- rename disable/enable_rpm_asserts to disable/enable_rpm_wakeref_asserts
and wakelock_count to wakeref_count
- disable the wakeref asserts in the IRQ handlers and RPS work too
- update/clarify commit message
v5:
- mark places we plan to change to use proper RPM refcounting with
separate DISABLE/ENABLE_RPM_WAKEREF_ASSERTS aliases (Chris)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1450227139-13471-1-git-send-email-imre.deak@intel.com
We don't really need to check this flag in the get/put/assert helpers,
as on platforms without RPM support we won't ever enable RPM. That means
pm.suspend will be always false and the assert will be always true.
Do this to simplify the code and to let us extend the RPM asserts to all
platforms for a better coverage.
Motivated by Ville.
v2-v3:
- unchanged
v4:
- remove the HAS_RUNTIME_PM check from intel_runtime_pm_enable() too
made possible by the previous two patches
v5:
- rebased on the previous new patch in the series that keeps
HAS_RUNTIME_PM() in intel_runtime_pm_enable() with a permanent
reference taken there
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v3)
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450352931-16498-1-git-send-email-imre.deak@intel.com
Currently we disable RPM functionality on platforms that doesn't support
this by not putting/getting the RPM reference we receive from the RPM
core during driver loading/unloading respectively. This is somewhat
obscure, so make it more explicit by keeping a reference dedicated for
this particular purpose whenever the driver is loaded. This makes it
possible to remove the HAS_RUNTIME_PM() special casing from every other
places in the next patch.
v2:
- fix intel_runtime_pm_get vs. intel_runtime_pm_put in
intel_power_domains_fini()
v3:
- take only a low level RPM reference so the ref tracking asserts
continue to work (Ville)
- update the commit message
- move the patch earlier for bisectability
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450352696-16135-1-git-send-email-imre.deak@intel.com
Imre Deak