This interface is designed for mixer/control application. To use hwdep
interface, the application can get information about firewire node, can
lock/unlock kernel streaming and can get notification at starting/stopping
kernel streaming.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a functionality to capture/playback PCM samples.
When AMDTP stream is already running for PCM or the source of clock is not
internal, available sampling rate is limited at current one.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a functionality to capture/playback MIDI messages.
When no AMDTP streams are running, this driver starts AMDTP stream for MIDI
stream at current sampling rate.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fireworks manages connections by CMP and can transmit/receive AMDTP streams
with a few quirks. This commit adds functionality to start/stop the streams.
Major Fireworks products don't support 'SYT-Match' clock source mode, except
for AudioFire12/8(till 2009 July) with firmware version 1.0. Already in
previous commit, this driver don't support such old firmwares. So this commit
adds support for non 'SYT-Match' clock source modes.
I note that this driver has a short gap for MIDI streams when starting PCM
stream. When AMDTP streams are running only for MIDI data and PCM data is
going to be joined at different sampling rate, then AMDTP streams are
stopped once and started again after changing sampling rate.
Unfortunately, Fireworks is not fully compliant to IEC 61883-1/6. Some commits
following to this commit add these quirks.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fireworks uses own command and response. This commit adds functionality to
transact and adds some commands required for sound card instance and kernel
streaming.
There are two ways to deliver substance of this transaction:
1.AV/C vendor dependent command for command/response
2.Async transaction to specific addresses for command/response
By way 1, I confirm AudioFire12 cannot correctly response to some commands with
firmware version 5.0 or later. This is also confirmed by FFADO. So this driver
implement way 2.
The address for response gives an issue. When this driver allocate own callback
function into the address, then no one can allocate its own callback function.
This situation is not good for applications in user-land. This issue is solved
in later commit.
I note there is a command to change the address for response if the device
supports. But this driver uses default value. So users should not execute this
command as long as hoping this driver works correctly.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a new driver for devices based on Fireworks. This driver
just creates/removes card instance according to callbacks.
Fireworks is a board module which Echo Audio produced. This module
consists of three chipsets:
- Communication chipset for IEEE1394 PHY/Link and IEC 61883-1/6
- DSP or/and FPGA for signal processing
- Flash Memory to store firmwares
Current supported devices:
- Mackie Onyx 400F/1200F
- Echo AudioFire12/8(until 2009 July)
- Echo AudioFire2/4/Pre8/8(since 2009 July)
- Echo Fireworks 8/HDMI
- Gibson Robot Interface pack/GoldTop
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Sakamoto