HDA Codec driver
Fix and cleanup of CM9880 automatic PIN configuration.
snd_hda_codec_setup_stream() doesn't do anything when NID is 0.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
EMU10K1/EMU10K2 driver
When building with gcc -W sound/pci/emu10k1/emupcm.c produces this little
warning in 2.6.12-rc2-mm3 :
sound/pci/emu10k1/emupcm.c:265: warning: 'inline' is not at beginning of
declaration
No big deal, but trivial to fix.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA generic driver,HDA Codec driver
Add initial SigmaTel codec support for 9200 and 922x. Note that
this hda patch relies on the configuration default registers to
be set correctly (normally by BIOS/firmware) in order for it to
set up pin widgets properly. There's a test switch in the patch
so it will work with the SigmaTel reference boards that are usually
plugged into a system that doesn't set the configuration default
registers. It supports 2 channel analog out and line/mic in. I
plan to add >2 channel support and spdif support shortly.
Please apply.
Signed-off-by: Matt <matt@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver,HDA generic driver
Fix some vref defines so they are valid for the different bits in
the pin cap and pin control registers. Please apply.
Signed-off-by: Matt <matt@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AC97 Codec
The handling of shared surround/clfe output jacks with line/mic-in
on some AC97 codecs is improved.
Instead of 'Line-In As Surround' or 'Mic As Center/LFE' switch, two
new enum controls are introduced: 'Channel Mode' and 'Surround Jack Mode'.
The formar changes the current output mode among 2, 4 and 6-channels.
The latter controls whether the jacks are shared or independent.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
PCM Midlevel,CA0106 driver,EMU10K1/EMU10K2 driver
Fix by Guillaume Chazarain <guichaz@yahoo.fr>:
Some tunables in /proc have a write() function, but as their
permission does not reflect it, it can be confusing to the user.
So here is a patch that corrects the mode of those files. Note that I
have only tested the 'xrun_debug' entry.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Documentation,VIA82xx driver
Add support for full sample rate conversion capabilities of DXS
channels present in VIA VT8233/5/7 controllers:
- any sample rate in the 8000 ... 48000 Hz range is supported even if
the AC'97 codec supports only 48000 Hz output;
- different DXS channels can use different sample rates at the same
time (the controller performs required sample rate conversion and
mixing in hardware).
Signed-off-by: Sergey Vlasov <vsu@altlinux.ru>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
FM801 driver
The Gallant Odyssey Sound 4 card is based on the ForteMedia FM801
chip, but has a different PCI ID.
Signed-off-by: Sergey Vlasov <vsu@altlinux.ru>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
YMFPCI driver
This patch removes some dead code found by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ICE1712 driver
Provides preliminary support for the Terratec Phase 28 card.
Not extensively tested and probably buggy, but it seems to work.
Signed-off-by: Simone Zinanni <simone@develer.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
EMU10K1/EMU10K2 driver
Although we can set 44100 as the output rate, the SPDIF can do it, but the Analog output cannot.
The SPDIF has the bug, whereby the Left channel arrives one sample late, so although we don't do any resampling,
it is not good for AC3 non-audio output.
Signed-off-by: James Courtier-Dutton <James@superbug.co.uk>
HDA Codec driver
Patch by C.L. Tien <cltien@cmedia.com.tw>:
The patch makes cm9880 to choose multi-channel jacks automatically.
1. I found the current code has basic_init, which already includes
necessary controls for 6-stack initialization, so I don't need
another model.
2. I add a new model 'auto' to let the driver find a. if there are
option real panel/front panel, b. the jacks to be used for multichannel.
Because the jack color are based on MS's channel sequence, so the 'auto'
model will pick the same jacks for multichannel MS uses. I did this to
hope to minimize users questions. These code can also be applied to other
codecs but I don't have any to test.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Intel8x0-modem driver
With some intel based ac97 modems codec access semaphore is not cleared
after 0x54 AC97 register (GPIO_STATUS) reads. This may causes problems
with newly applied modem mixer (Off-hook switch) and in other cases.
Signed-off-by: Sasha Khapyorsky <sashak@smlink.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AC97 Codec
- Added CM9780 patch
- Fix the SPDIF support on CM9761/CM9780
- Allow the generic enum callback to pass any number (not power of 2)
as the value mask
Signed-off-by: Takashi Iwai <tiwai@suse.de>
EMU10K1/EMU10K2 driver
This add identification of Audigy 1 model SB0090 and fixes
problems with ac97 codec (mic not working).
Signed-off-by: Peter Zubaj <pzad@pobox.sk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
EMU10K1/EMU10K2 driver
Use expliciitly the old default id strings for backward compatibility.
This will make 'alsactl restore' working again.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
EMU10K1/EMU10K2 driver
This patch converts the emu10k1 driver to use the card capabilities
structure for some more things.
Not extensively tested but seems to work.
Signed-off-by: Lee Revell <rlrevell@joe-job.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AC97 Codec
Fixed the detection of bit resolution of ac97 mixer controls.
This will fix the problem with TI ac97 codecs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
EMU10K1/EMU10K2 driver
One can select which capture source, but one cannot yet set volumes.
Signed-off-by: James Courtier-Dutton <James@superbug.co.uk>
HDA Codec driver
The patch_cm9880.c can't play side/C/B channels from front panel jacks.
I fixed it by adding select pin.
Signed-off-by: ChenLi Tien <cltien@cmedia.com.tw>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA generic driver
During debugging for cm9880 multi-channel playback, I added the * after
the currently selected widget, mixer widget doesn't need this but other
3 widget types need it.
Signed-off-by: ChenLi Tien <cltien@cmedia.com.tw>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Trying software suspend on my workstation makes it crash on resume. The
problem is that via82xx marks the chip_init function as _devinit, but calls
it on resume as well.
Cc: <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes a typo in the Intel AC'97 audio driver intel8x0.c for
Intel ESB2.
Signed-off-by: Jason Gaston <Jason.d.gaston@intel.com>
Cc: <tiwai@suse.de>
Cc: <perex@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds the Intel ESB2 HD Audio DID to the hda_intel.c audio driver.
Signed-off-by: Jason Gaston <Jason.d.gaston@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I thought I'm done with fixing u32 vs. pm_message_t ... unfortunately that
turned out not to be the case as Russel King pointed out. This fixes last few
bits in alsa.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds the Intel ESB2 DID's to the intel8x0.c file for AC'97 audio
support.
Signed-off-by: Jason Gaston <Jason.d.gaston@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Takashi Iwai