- Parallel CPU bringup
The reason why people are interested in parallel bringup is to shorten
the (kexec) reboot time of cloud servers to reduce the downtime of the
VM tenants.
The current fully serialized bringup does the following per AP:
1) Prepare callbacks (allocate, intialize, create threads)
2) Kick the AP alive (e.g. INIT/SIPI on x86)
3) Wait for the AP to report alive state
4) Let the AP continue through the atomic bringup
5) Let the AP run the threaded bringup to full online state
There are two significant delays:
#3 The time for an AP to report alive state in start_secondary() on
x86 has been measured in the range between 350us and 3.5ms
depending on vendor and CPU type, BIOS microcode size etc.
#4 The atomic bringup does the microcode update. This has been
measured to take up to ~8ms on the primary threads depending on
the microcode patch size to apply.
On a two socket SKL server with 56 cores (112 threads) the boot CPU
spends on current mainline about 800ms busy waiting for the APs to come
up and apply microcode. That's more than 80% of the actual onlining
procedure.
This can be reduced significantly by splitting the bringup mechanism
into two parts:
1) Run the prepare callbacks and kick the AP alive for each AP which
needs to be brought up.
The APs wake up, do their firmware initialization and run the low
level kernel startup code including microcode loading in parallel
up to the first synchronization point. (#1 and #2 above)
2) Run the rest of the bringup code strictly serialized per CPU
(#3 - #5 above) as it's done today.
Parallelizing that stage of the CPU bringup might be possible in
theory, but it's questionable whether required surgery would be
justified for a pretty small gain.
If the system is large enough the first AP is already waiting at the
first synchronization point when the boot CPU finished the wake-up of
the last AP. That reduces the AP bringup time on that SKL from ~800ms
to ~80ms, i.e. by a factor ~10x.
The actual gain varies wildly depending on the system, CPU, microcode
patch size and other factors. There are some opportunities to reduce
the overhead further, but that needs some deep surgery in the x86 CPU
bringup code.
For now this is only enabled on x86, but the core functionality
obviously works for all SMP capable architectures.
- Enhancements for SMP function call tracing so it is possible to locate
the scheduling and the actual execution points. That allows to measure
IPI delivery time precisely.
-----BEGIN PGP SIGNATURE-----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=Y8if
-----END PGP SIGNATURE-----
Merge tag 'smp-core-2023-06-26' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull SMP updates from Thomas Gleixner:
"A large update for SMP management:
- Parallel CPU bringup
The reason why people are interested in parallel bringup is to
shorten the (kexec) reboot time of cloud servers to reduce the
downtime of the VM tenants.
The current fully serialized bringup does the following per AP:
1) Prepare callbacks (allocate, intialize, create threads)
2) Kick the AP alive (e.g. INIT/SIPI on x86)
3) Wait for the AP to report alive state
4) Let the AP continue through the atomic bringup
5) Let the AP run the threaded bringup to full online state
There are two significant delays:
#3 The time for an AP to report alive state in start_secondary()
on x86 has been measured in the range between 350us and 3.5ms
depending on vendor and CPU type, BIOS microcode size etc.
#4 The atomic bringup does the microcode update. This has been
measured to take up to ~8ms on the primary threads depending
on the microcode patch size to apply.
On a two socket SKL server with 56 cores (112 threads) the boot CPU
spends on current mainline about 800ms busy waiting for the APs to
come up and apply microcode. That's more than 80% of the actual
onlining procedure.
This can be reduced significantly by splitting the bringup
mechanism into two parts:
1) Run the prepare callbacks and kick the AP alive for each AP
which needs to be brought up.
The APs wake up, do their firmware initialization and run the
low level kernel startup code including microcode loading in
parallel up to the first synchronization point. (#1 and #2
above)
2) Run the rest of the bringup code strictly serialized per CPU
(#3 - #5 above) as it's done today.
Parallelizing that stage of the CPU bringup might be possible
in theory, but it's questionable whether required surgery
would be justified for a pretty small gain.
If the system is large enough the first AP is already waiting at
the first synchronization point when the boot CPU finished the
wake-up of the last AP. That reduces the AP bringup time on that
SKL from ~800ms to ~80ms, i.e. by a factor ~10x.
The actual gain varies wildly depending on the system, CPU,
microcode patch size and other factors. There are some
opportunities to reduce the overhead further, but that needs some
deep surgery in the x86 CPU bringup code.
For now this is only enabled on x86, but the core functionality
obviously works for all SMP capable architectures.
- Enhancements for SMP function call tracing so it is possible to
locate the scheduling and the actual execution points. That allows
to measure IPI delivery time precisely"
* tag 'smp-core-2023-06-26' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tip/tip: (45 commits)
trace,smp: Add tracepoints for scheduling remotelly called functions
trace,smp: Add tracepoints around remotelly called functions
MAINTAINERS: Add CPU HOTPLUG entry
x86/smpboot: Fix the parallel bringup decision
x86/realmode: Make stack lock work in trampoline_compat()
x86/smp: Initialize cpu_primary_thread_mask late
cpu/hotplug: Fix off by one in cpuhp_bringup_mask()
x86/apic: Fix use of X{,2}APIC_ENABLE in asm with older binutils
x86/smpboot/64: Implement arch_cpuhp_init_parallel_bringup() and enable it
x86/smpboot: Support parallel startup of secondary CPUs
x86/smpboot: Implement a bit spinlock to protect the realmode stack
x86/apic: Save the APIC virtual base address
cpu/hotplug: Allow "parallel" bringup up to CPUHP_BP_KICK_AP_STATE
x86/apic: Provide cpu_primary_thread mask
x86/smpboot: Enable split CPU startup
cpu/hotplug: Provide a split up CPUHP_BRINGUP mechanism
cpu/hotplug: Reset task stack state in _cpu_up()
cpu/hotplug: Remove unused state functions
riscv: Switch to hotplug core state synchronization
parisc: Switch to hotplug core state synchronization
...
Switch to the CPU hotplug core state tracking and synchronization
mechanim. No functional change intended.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Michael Kelley <mikelley@microsoft.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Tested-by: Helge Deller <deller@gmx.de> # parisc
Tested-by: Guilherme G. Piccoli <gpiccoli@igalia.com> # Steam Deck
Link: https://lore.kernel.org/r/20230512205256.859920443@linutronix.de
We introduce a new HAS_IOPORT Kconfig option to indicate support for I/O
Port access. In a future patch HAS_IOPORT=n will disable compilation of
the I/O accessor functions inb()/outb() and friends on architectures
which can not meaningfully support legacy I/O spaces such as s390.
The following architectures do not select HAS_IOPORT:
* ARC
* C-SKY
* Hexagon
* Nios II
* OpenRISC
* s390
* User-Mode Linux
* Xtensa
All other architectures select HAS_IOPORT at least conditionally.
The "depends on" relations on HAS_IOPORT in drivers as well as ifdefs
for HAS_IOPORT specific sections will be added in subsequent patches on
a per subsystem basis.
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net> # for ARCH=um
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The previous patch triggered a build failure for the debian kernel,
which has CONFIG_64BIT enabled, uses the CROSS_COMPILER environment
variable and uses ARCH=parisc to configure the kernel for 64-bit
support.
This patch weakens the previous patch while keeping the recommended way
to configure the kernel with:
ARCH=parisc -> build 32-bit kernel
ARCH=parisc64 -> build 64-bit kernel
while adding the possibility for debian to configure a 64-bit kernel
even if ARCH=parisc is set (PA8X00 CPU has to be selected and
CONFIG_64BIT needs to be enabled).
The downside of this patch is, that we now have a small window open
again where people may get it wrong: if they enable CONFIG_64BIT and try
to compile with a 32-bit compiler.
Fixes: 3dcfb729b5 ("parisc: Make CONFIG_64BIT available for ARCH=parisc64 only")
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org> # 5.15+
With this patch the ARCH= parameter decides if the
CONFIG_64BIT option will be set or not. This means, the
ARCH= parameter will give:
ARCH=parisc -> 32-bit kernel
ARCH=parisc64 -> 64-bit kernel
This simplifies the usage of the other config options like
randconfig, allmodconfig and allyesconfig a lot and produces
the output which is expected for parisc64 (64-bit) vs. parisc (32-bit).
Suggested-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Cc: <stable@vger.kernel.org> # 5.15+
There are three independent sets of changes:
- Sai Prakash Ranjan adds tracing support to the asm-generic
version of the MMIO accessors, which is intended to help
understand problems with device drivers and has been part
of Qualcomm's vendor kernels for many years.
- A patch from Sebastian Siewior to rework the handling of
IRQ stacks in softirqs across architectures, which is
needed for enabling PREEMPT_RT.
- The last patch to remove the CONFIG_VIRT_TO_BUS option and
some of the code behind that, after the last users of this
old interface made it in through the netdev, scsi, media and
staging trees.
-----BEGIN PGP SIGNATURE-----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=aTR0
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"There are three independent sets of changes:
- Sai Prakash Ranjan adds tracing support to the asm-generic version
of the MMIO accessors, which is intended to help understand
problems with device drivers and has been part of Qualcomm's vendor
kernels for many years
- A patch from Sebastian Siewior to rework the handling of IRQ stacks
in softirqs across architectures, which is needed for enabling
PREEMPT_RT
- The last patch to remove the CONFIG_VIRT_TO_BUS option and some of
the code behind that, after the last users of this old interface
made it in through the netdev, scsi, media and staging trees"
* tag 'asm-generic-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
uapi: asm-generic: fcntl: Fix typo 'the the' in comment
arch/*/: remove CONFIG_VIRT_TO_BUS
soc: qcom: geni: Disable MMIO tracing for GENI SE
serial: qcom_geni_serial: Disable MMIO tracing for geni serial
asm-generic/io: Add logging support for MMIO accessors
KVM: arm64: Add a flag to disable MMIO trace for nVHE KVM
lib: Add register read/write tracing support
drm/meson: Fix overflow implicit truncation warnings
irqchip/tegra: Fix overflow implicit truncation warnings
coresight: etm4x: Use asm-generic IO memory barriers
arm64: io: Use asm-generic high level MMIO accessors
arch/*: Disable softirq stacks on PREEMPT_RT.
All architecture-independent users of virt_to_bus() and bus_to_virt()
have been fixed to use the dma mapping interfaces or have been
removed now. This means the definitions on most architectures, and the
CONFIG_VIRT_TO_BUS symbol are now obsolete and can be removed.
The only exceptions to this are a few network and scsi drivers for m68k
Amiga and VME machines and ppc32 Macintosh. These drivers work correctly
with the old interfaces and are probably not worth changing.
On alpha and parisc, virt_to_bus() were still used in asm/floppy.h.
alpha can use isa_virt_to_bus() like x86 does, and parisc can just
open-code the virt_to_phys() here, as this is architecture specific
code.
I tried updating the bus-virt-phys-mapping.rst documentation, which
started as an email from Linus to explain some details of the Linux-2.0
driver interfaces. The bits about virt_to_bus() were declared obsolete
backin 2000, and the rest is not all that relevant any more, so in the
end I just decided to remove the file completely.
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Acked-by: Helge Deller <deller@gmx.de> # parisc
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fix a boot crash on a c8000 machine as reported by Dave. Basically it changes
patch_map() to return an alias mapping to the to-be-patched code in order to
prevent writing to write-protected memory.
Signed-off-by: Helge Deller <deller@gmx.de>
Suggested-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # v5.2+
Link: https://lore.kernel.org/all/e8ec39e8-25f8-e6b4-b7ed-4cb23efc756e@bell.net/
* Support for the Svpbmt extension, which allows memory attributes to be
encoded in pages.
* Support for the Allwinner D1's implementation of page-based memory
attributes.
* Support for running rv32 binaries on rv64 systems, via the compat
subsystem.
* Support for kexec_file().
* Support for the new generic ticket-based spinlocks, which allows us to
also move to qrwlock. These should have already gone in through the
asm-geneic tree as well.
* A handful of cleanups and fixes, include some larger ones around
atomics and XIP.
-----BEGIN PGP SIGNATURE-----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=Loi6
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-5.19-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Palmer Dabbelt:
- Support for the Svpbmt extension, which allows memory attributes to
be encoded in pages
- Support for the Allwinner D1's implementation of page-based memory
attributes
- Support for running rv32 binaries on rv64 systems, via the compat
subsystem
- Support for kexec_file()
- Support for the new generic ticket-based spinlocks, which allows us
to also move to qrwlock. These should have already gone in through
the asm-geneic tree as well
- A handful of cleanups and fixes, include some larger ones around
atomics and XIP
* tag 'riscv-for-linus-5.19-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (51 commits)
RISC-V: Prepare dropping week attribute from arch_kexec_apply_relocations[_add]
riscv: compat: Using seperated vdso_maps for compat_vdso_info
RISC-V: Fix the XIP build
RISC-V: Split out the XIP fixups into their own file
RISC-V: ignore xipImage
RISC-V: Avoid empty create_*_mapping definitions
riscv: Don't output a bogus mmu-type on a no MMU kernel
riscv: atomic: Add custom conditional atomic operation implementation
riscv: atomic: Optimize dec_if_positive functions
riscv: atomic: Cleanup unnecessary definition
RISC-V: Load purgatory in kexec_file
RISC-V: Add purgatory
RISC-V: Support for kexec_file on panic
RISC-V: Add kexec_file support
RISC-V: use memcpy for kexec_file mode
kexec_file: Fix kexec_file.c build error for riscv platform
riscv: compat: Add COMPAT Kbuild skeletal support
riscv: compat: ptrace: Add compat_arch_ptrace implement
riscv: compat: signal: Add rt_frame implementation
riscv: add memory-type errata for T-Head
...
In commit 62773112ac ("parisc: Switch from GENERIC_CPU_DEVICES to
GENERIC_ARCH_TOPOLOGY") GENERIC_CPU_DEVICES was unconditionally turned
off, but this triggers a warning in topology_add_dev(). Turning it back
on for the !SMP case avoids this warning.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Fixes: 62773112ac ("parisc: Switch from GENERIC_CPU_DEVICES to GENERIC_ARCH_TOPOLOGY")
Signed-off-by: Helge Deller <deller@gmx.de>
Add relevant code to __cpu_die() and __cpu_disable() to finally enable
the CPU hotplugging features. Reset the irq count values in smp_callin()
to zero before bringing up the CPU.
It seems that the firmware may need up to 8 seconds to fully stop a CPU
in which no other PDC calls are allowed to be made. Use a timeout
__cpu_die() to accommodate for this.
Use "chcpu -d 1" to bring CPU1 down, and "chcpu -e 1" to bring it up.
Signed-off-by: Helge Deller <deller@gmx.de>
Switch away from the own cpu topology code to common code which is used
by ARM64 and RISCV. That will allow us to enable CPU hotplug later on.
Signed-off-by: Helge Deller <deller@gmx.de>
- Enforce kernel RO, and implement STRICT_MODULE_RWX for 603.
- Add support for livepatch to 32-bit.
- Implement CONFIG_DYNAMIC_FTRACE_WITH_ARGS.
- Merge vdso64 and vdso32 into a single directory.
- Fix build errors with newer binutils.
- Add support for UADDR64 relocations, which are emitted by some toolchains. This allows
powerpc to build with the latest lld.
- Fix (another) potential userspace r13 corruption in transactional memory handling.
- Cleanups of function descriptor handling & related fixes to LKDTM.
Thanks to: Abdul Haleem, Alexey Kardashevskiy, Anders Roxell, Aneesh Kumar K.V, Anton
Blanchard, Arnd Bergmann, Athira Rajeev, Bhaskar Chowdhury, Cédric Le Goater, Chen
Jingwen, Christophe JAILLET, Christophe Leroy, Corentin Labbe, Daniel Axtens, Daniel
Henrique Barboza, David Dai, Fabiano Rosas, Ganesh Goudar, Guo Zhengkui, Hangyu Hua, Haren
Myneni, Hari Bathini, Igor Zhbanov, Jakob Koschel, Jason Wang, Jeremy Kerr, Joachim
Wiberg, Jordan Niethe, Julia Lawall, Kajol Jain, Kees Cook, Laurent Dufour, Madhavan
Srinivasan, Mamatha Inamdar, Maxime Bizon, Maxim Kiselev, Maxim Kochetkov, Michal
Suchanek, Nageswara R Sastry, Nathan Lynch, Naveen N. Rao, Nicholas Piggin, Nour-eddine
Taleb, Paul Menzel, Ping Fang, Pratik R. Sampat, Randy Dunlap, Ritesh Harjani, Rohan
McLure, Russell Currey, Sachin Sant, Segher Boessenkool, Shivaprasad G Bhat, Sourabh Jain,
Thierry Reding, Tobias Waldekranz, Tyrel Datwyler, Vaibhav Jain, Vladimir Oltean, Wedson
Almeida Filho, YueHaibing.
-----BEGIN PGP SIGNATURE-----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=8r2c
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Livepatch support for 32-bit is probably the standout new feature,
otherwise mostly just lots of bits and pieces all over the board.
There's a series of commits cleaning up function descriptor handling,
which touches a few other arches as well as LKDTM. It has acks from
Arnd, Kees and Helge.
Summary:
- Enforce kernel RO, and implement STRICT_MODULE_RWX for 603.
- Add support for livepatch to 32-bit.
- Implement CONFIG_DYNAMIC_FTRACE_WITH_ARGS.
- Merge vdso64 and vdso32 into a single directory.
- Fix build errors with newer binutils.
- Add support for UADDR64 relocations, which are emitted by some
toolchains. This allows powerpc to build with the latest lld.
- Fix (another) potential userspace r13 corruption in transactional
memory handling.
- Cleanups of function descriptor handling & related fixes to LKDTM.
Thanks to Abdul Haleem, Alexey Kardashevskiy, Anders Roxell, Aneesh
Kumar K.V, Anton Blanchard, Arnd Bergmann, Athira Rajeev, Bhaskar
Chowdhury, Cédric Le Goater, Chen Jingwen, Christophe JAILLET,
Christophe Leroy, Corentin Labbe, Daniel Axtens, Daniel Henrique
Barboza, David Dai, Fabiano Rosas, Ganesh Goudar, Guo Zhengkui, Hangyu
Hua, Haren Myneni, Hari Bathini, Igor Zhbanov, Jakob Koschel, Jason
Wang, Jeremy Kerr, Joachim Wiberg, Jordan Niethe, Julia Lawall, Kajol
Jain, Kees Cook, Laurent Dufour, Madhavan Srinivasan, Mamatha Inamdar,
Maxime Bizon, Maxim Kiselev, Maxim Kochetkov, Michal Suchanek,
Nageswara R Sastry, Nathan Lynch, Naveen N. Rao, Nicholas Piggin,
Nour-eddine Taleb, Paul Menzel, Ping Fang, Pratik R. Sampat, Randy
Dunlap, Ritesh Harjani, Rohan McLure, Russell Currey, Sachin Sant,
Segher Boessenkool, Shivaprasad G Bhat, Sourabh Jain, Thierry Reding,
Tobias Waldekranz, Tyrel Datwyler, Vaibhav Jain, Vladimir Oltean,
Wedson Almeida Filho, and YueHaibing"
* tag 'powerpc-5.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (179 commits)
powerpc/pseries: Fix use after free in remove_phb_dynamic()
powerpc/time: improve decrementer clockevent processing
powerpc/time: Fix KVM host re-arming a timer beyond decrementer range
powerpc/tm: Fix more userspace r13 corruption
powerpc/xive: fix return value of __setup handler
powerpc/64: Add UADDR64 relocation support
powerpc: 8xx: fix a return value error in mpc8xx_pic_init
powerpc/ps3: remove unneeded semicolons
powerpc/64: Force inlining of prevent_user_access() and set_kuap()
powerpc/bitops: Force inlining of fls()
powerpc: declare unmodified attribute_group usages const
powerpc/spufs: Fix build warning when CONFIG_PROC_FS=n
powerpc/secvar: fix refcount leak in format_show()
powerpc/64e: Tie PPC_BOOK3E_64 to PPC_FSL_BOOK3E
powerpc: Move C prototypes out of asm-prototypes.h
powerpc/kexec: Declare kexec_paca static
powerpc/smp: Declare current_set static
powerpc: Cleanup asm-prototypes.c
powerpc/ftrace: Use STK_GOT in ftrace_mprofile.S
powerpc/ftrace: Regroup PPC64 specific operations in ftrace_mprofile.S
...
There are three sets of updates for 5.18 in the asm-generic tree:
- The set_fs()/get_fs() infrastructure gets removed for good. This
was already gone from all major architectures, but now we can
finally remove it everywhere, which loses some particularly
tricky and error-prone code.
There is a small merge conflict against a parisc cleanup, the
solution is to use their new version.
- The nds32 architecture ends its tenure in the Linux kernel. The
hardware is still used and the code is in reasonable shape, but
the mainline port is not actively maintained any more, as all
remaining users are thought to run vendor kernels that would never
be updated to a future release.
There are some obvious conflicts against changes to the removed
files.
- A series from Masahiro Yamada cleans up some of the uapi header
files to pass the compile-time checks.
-----BEGIN PGP SIGNATURE-----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=vtCN
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"There are three sets of updates for 5.18 in the asm-generic tree:
- The set_fs()/get_fs() infrastructure gets removed for good.
This was already gone from all major architectures, but now we can
finally remove it everywhere, which loses some particularly tricky
and error-prone code. There is a small merge conflict against a
parisc cleanup, the solution is to use their new version.
- The nds32 architecture ends its tenure in the Linux kernel.
The hardware is still used and the code is in reasonable shape, but
the mainline port is not actively maintained any more, as all
remaining users are thought to run vendor kernels that would never
be updated to a future release.
- A series from Masahiro Yamada cleans up some of the uapi header
files to pass the compile-time checks"
* tag 'asm-generic-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (27 commits)
nds32: Remove the architecture
uaccess: remove CONFIG_SET_FS
ia64: remove CONFIG_SET_FS support
sh: remove CONFIG_SET_FS support
sparc64: remove CONFIG_SET_FS support
lib/test_lockup: fix kernel pointer check for separate address spaces
uaccess: generalize access_ok()
uaccess: fix type mismatch warnings from access_ok()
arm64: simplify access_ok()
m68k: fix access_ok for coldfire
MIPS: use simpler access_ok()
MIPS: Handle address errors for accesses above CPU max virtual user address
uaccess: add generic __{get,put}_kernel_nofault
nios2: drop access_ok() check from __put_user()
x86: use more conventional access_ok() definition
x86: remove __range_not_ok()
sparc64: add __{get,put}_kernel_nofault()
nds32: fix access_ok() checks in get/put_user
uaccess: fix nios2 and microblaze get_user_8()
sparc64: fix building assembly files
...
This patch drops the CONFIG_PARISC_SELF_EXTRACT option.
The palo boot loader is able to decompress a kernel which was compressed
with gzip. That possibility was useful when the Linux kernel
self-extracting feature wasn't implemented yet.
Beside the fact that the self-extracting feature offers much better
compression rates, we do support self-extracting kernels already since
kernel v4.14, so now it's really time to get rid of that old option and
always use the self-extractor.
Signed-off-by: Helge Deller <deller@gmx.de>
Add minimal vDSO support, which provides the signal trampoline helpers,
but none of the userspace syscall helpers like time wrappers.
The big benefit of this vDSO implementation is, that we now don't need
an executeable stack any longer. PA-RISC is one of the last
architectures where an executeable stack was needed in oder to implement
the signal trampolines by putting assembly instructions on the stack
which then gets executed. Instead the kernel will provide the relevant
code in the vDSO page and only put the pointers to the signal
information on the stack.
By dropping the need for executable stacks we avoid running into issues
with applications which want non executable stacks for security reasons.
Additionally, alternative stacks on memory areas without exec
permissions are supported too.
This code is based on an initial implementation by Randolph Chung from 2006:
https://lore.kernel.org/linux-parisc/4544A34A.6080700@tausq.org/
I did the porting and lifted the code to current code base. Dave fixed
the unwind code so that gdb and glibc are able to backtrace through the
code. An additional patch to gdb will be pushed upstream by Dave.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Dave Anglin <dave.anglin@bell.net>
Cc: Randolph Chung <randolph@tausq.org>
Signed-off-by: Helge Deller <deller@gmx.de>
There are many different ways that access_ok() is defined across
architectures, but in the end, they all just compare against the
user_addr_max() value or they accept anything.
Provide one definition that works for most architectures, checking
against TASK_SIZE_MAX for user processes or skipping the check inside
of uaccess_kernel() sections.
For architectures without CONFIG_SET_FS(), this should be the fastest
check, as it comes down to a single comparison of a pointer against a
compile-time constant, while the architecture specific versions tend to
do something more complex for historic reasons or get something wrong.
Type checking for __user annotations is handled inconsistently across
architectures, but this is easily simplified as well by using an inline
function that takes a 'const void __user *' argument. A handful of
callers need an extra __user annotation for this.
Some architectures had trick to use 33-bit or 65-bit arithmetic on the
addresses to calculate the overflow, however this simpler version uses
fewer registers, which means it can produce better object code in the
end despite needing a second (statically predicted) branch.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Mark Rutland <mark.rutland@arm.com> [arm64, asm-generic]
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Stafford Horne <shorne@gmail.com>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Replace HAVE_DEREFERENCE_FUNCTION_DESCRIPTOR by a config option
named CONFIG_HAVE_FUNCTION_DESCRIPTORS and use it instead of
'dereference_function_descriptor' macro to know whether an
arch has function descriptors.
To limit churn in one of the following patches, use
an #ifdef/#else construct with empty first part
instead of an #ifndef in asm-generic/sections.h
On powerpc, make sure the config option matches the ABI used
by the compiler with a BUILD_BUG_ON() and add missing _CALL_ELF=2
when calling 'sparse' so that sparse sees the same piece of
code as GCC.
And include a helper to check whether an arch has function
descriptors or not : have_function_descriptors()
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Helge Deller <deller@gmx.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/4a0f11fb0ea74a3197bc44dd7ba25e53a24fd03d.1644928018.git.christophe.leroy@csgroup.eu
Qemu currently supports up to 16 CPUs, so increase the default from 4 to 16.
Bload-o-meter shows only an increase of 800 bytes with this change.
Signed-off-by: Helge Deller <deller@gmx.de>
Before this patch, the TOC code used a pre-allocated stack of 16kb for
each possible CPU. That space overhead was the reason why the TOC
feature wasn't enabled by default for 32-bit kernels.
This patch rewrites the TOC code to use a per-cpu stack. That way we use
much less memory now and as such we enable the TOC feature by default on
all kernels.
Additionally the dump of the registers and the stacktrace wasn't
serialized, which led to multiple CPUs printing the stack backtrace at
once which rendered the output unreadable.
Now the backtraces are nicely serialized by a lock.
Signed-off-by: Helge Deller <deller@gmx.de>
Commit 2a86f66121 ("kbuild: use KBUILD_DEFCONFIG as the fallback for
DEFCONFIG_LIST") removed ARCH_DEFCONFIG because it does not make much
sense.
In the same development cycle, Commit ededa081ed ("parisc: Fix
defconfig selection") added ARCH_DEFCONFIG for parisc.
Please use KBUILD_DEFCONFIG in arch/*/Makefile for defconfig selection.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Acked-by: Helge Deller <deller@gmx.de>
Signed-off-by: Helge Deller <deller@gmx.de>
This implements the CONFIG_THREAD_INFO_IN_TASK option.
With this change:
- before thread_info was part of the stack and located at the beginning of the stack
- now the thread_info struct is moved and located inside the task_struct structure
- the stack is allocated and handled like the major other platforms
- drop the cpu field of thread_info and use instead the one in task_struct
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Almost all PA-RISC machines have either a button that
is labeled with 'TOC' or a BMC function to trigger a TOC.
TOC is a non-maskable interrupt that is sent to the processor.
This can be used for diagnostic purposes like obtaining a
stack trace/register dump or to enter KDB/KGDB.
As an example, on my c8000, TOC can be used with:
CONFIG_KGDB=y
CONFIG_KGDB_KDB=y
and the 'kgdboc=ttyS0,115200' appended to the command line.
Press ^[( on serial console, which will enter the BMC command line,
and enter 'TOC s':
root@(none):/# (
cli>TOC s
Sending TOC/INIT.
<Cpu3> 2800035d03e00000 0000000040c21ac8 CC_ERR_CHECK_TOC
<Cpu0> 2800035d00e00000 0000000040c21ad0 CC_ERR_CHECK_TOC
<Cpu2> 2800035d02e00000 0000000040c21ac8 CC_ERR_CHECK_TOC
<Cpu1> 2800035d01e00000 0000000040c21ad0 CC_ERR_CHECK_TOC
<Cpu3> 37000f7303e00000 2000000000000000 CC_ERR_CPU_CHECK_SUMMARY
<Cpu0> 37000f7300e00000 2000000000000000 CC_ERR_CPU_CHECK_SUMMARY
<Cpu2> 37000f7302e00000 2000000000000000 CC_ERR_CPU_CHECK_SUMMARY
<Cpu1> 37000f7301e00000 2000000000000000 CC_ERR_CPU_CHECK_SUMMARY
<Cpu3> 4300100803e00000 c0000000001d26cc CC_MC_BR_TO_OS_TOC
<Cpu0> 4300100800e00000 c0000000001d26cc CC_MC_BR_TO_OS_TOC
<Cpu2> 4300100802e00000 c0000000001d26cc CC_MC_BR_TO_OS_TOC
<Cpu1> 4300100801e00000 c0000000001d26cc CC_MC_BR_TO_OS_TOC
Entering kdb (current=0x00000000411cef80, pid 0) on processor 0 due to NonMaskable Interrupt @ 0x40c21ad0
[0]kdb>
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Compile-testing drivers that require access to a firmware layer
fails when that firmware symbol is unavailable. This happened
twice this week:
- My proposed to change to rework the QCOM_SCM firmware symbol
broke on ppc64 and others.
- The cs_dsp firmware patch added device specific firmware loader
into drivers/firmware, which broke on the same set of
architectures.
We should probably do the same thing for other subsystems as well,
but fix this one first as this is a dependency for other patches
getting merged.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Will Deacon <will@kernel.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Charles Keepax <ckeepax@opensource.cirrus.com>
Cc: Simon Trimmer <simont@opensource.cirrus.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Remove CONFIG_SET_FS from parisc, so we need to add
__get_kernel_nofault() and __put_kernel_nofault(), define
HAVE_GET_KERNEL_NOFAULT and remove set_fs(), get_fs(), load_sr2(),
thread_info->addr_limit, KERNEL_DS and USER_DS.
The nice side-effect of this patch is that we now can directly access
userspace via sr3 without the need to use a temporary sr2 which is
either copied from sr3 or set to zero (for kernel space).
Signed-off-by: Helge Deller <deller@gmx.de>
Suggested-by: Arnd Bergmann <arnd@kernel.org>
As suggested by Arnd Bergmann, drop the parisc version of
strnlen_user() and switch to the generic version.
Suggested-by: Arnd Bergmann <arnd@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Helge Deller <deller@gmx.de>
- Simplifying the Kconfig use of FTRACE and TRACE_IRQFLAGS_SUPPORT
- bootconfig now can start histograms
- bootconfig supports group/all enabling
- histograms now can put values in linear size buckets
- execnames can be passed to synthetic events
- Introduction of "event probes" that attach to other events and
can retrieve data from pointers of fields, or record fields
as different types (a pointer to a string as a string instead
of just a hex number)
- Various fixes and clean ups
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCYTJDixQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qnPLAP9XviWrZD27uFj6LU/Vp2umbq8la1aC
oW8o9itUGpLoHQD+OtsMpQXsWrxoNw/JD1OWCH4J0YN+TnZAUUG2E9e0twA=
=OZXG
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
- simplify the Kconfig use of FTRACE and TRACE_IRQFLAGS_SUPPORT
- bootconfig can now start histograms
- bootconfig supports group/all enabling
- histograms now can put values in linear size buckets
- execnames can be passed to synthetic events
- introduce "event probes" that attach to other events and can retrieve
data from pointers of fields, or record fields as different types (a
pointer to a string as a string instead of just a hex number)
- various fixes and clean ups
* tag 'trace-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (35 commits)
tracing/doc: Fix table format in histogram code
selftests/ftrace: Add selftest for testing duplicate eprobes and kprobes
selftests/ftrace: Add selftest for testing eprobe events on synthetic events
selftests/ftrace: Add test case to test adding and removing of event probe
selftests/ftrace: Fix requirement check of README file
selftests/ftrace: Add clear_dynamic_events() to test cases
tracing: Add a probe that attaches to trace events
tracing/probes: Reject events which have the same name of existing one
tracing/probes: Have process_fetch_insn() take a void * instead of pt_regs
tracing/probe: Change traceprobe_set_print_fmt() to take a type
tracing/probes: Use struct_size() instead of defining custom macros
tracing/probes: Allow for dot delimiter as well as slash for system names
tracing/probe: Have traceprobe_parse_probe_arg() take a const arg
tracing: Have dynamic events have a ref counter
tracing: Add DYNAMIC flag for dynamic events
tracing: Replace deprecated CPU-hotplug functions.
MAINTAINERS: Add an entry for os noise/latency
tracepoint: Fix kerneldoc comments
bootconfig/tracing/ktest: Update ktest example for boot-time tracing
tools/bootconfig: Use per-group/all enable option in ftrace2bconf script
...
The main content for 5.15 is a series that cleans up the handling of
strncpy_from_user() and strnlen_user(), removing a lot of slightly
incorrect versions of these in favor of the lib/strn*.c helpers
that implement these correctly and more efficiently.
The only architectures that retain a private version now are
mips, ia64, um and parisc. I had offered to convert those at all,
but Thomas Bogendoerfer wanted to keep the mips version for the
moment until he had a chance to do regression testing.
The branch also contains two patches for bitops and for ffs().
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIVAwUAYS82fGCrR//JCVInAQL9AxAAruOge7r8vzXQC8ehR4iw4/pCyzsLWdjh
bLvTCovhD6y1KXb0cU3qMI2SUESwy/w9YteyLs4Edh5Yhm9uWIXz2WO6zTNDuW1g
eNd6lcmoOLOXFxCUX3TZqvnxaEEiedjEJjOTicTBRv8c79Kw+2DTFYEwi8MIWlbx
gGdGLOJ2SORl6HeE+wn8bfMPCChisMod75koi+Vnp3kp9+aw8VIi0RVMjtZ4HI3v
z9H0DD0jDAy1eaXnC2+dsaIyrAq8/Lo/pqVBvUJRoBFaV/FHvNH2M0yl15yJYx1V
1KNJlBhoedc0PiMO9OnsRS1GMq1kEeo+u9gJPqphZQWooAQotD5C0sXsPnsghGo0
IrsVANy4H0k2h0AazRZd3KwV03aJ6FWHz3qyvbglLAQjKU1MgZTgroF5Q6R2FMtV
/VtswpGB707+oGtmFvHc1lVgRYZTfduGT1jjBgwUuTUmLhI3/yRIlnodd6dXneX6
FOK3WbxlhUuIaSZLObLved/yNBgoOajP3vHIUc4c9HrsPEvkjKPB1g/VpbqqWVXe
vF5/MeUN+b3Rq+h1GnnZQmhiOPIydZmK3qK7zYzp5Da+Ke4I2zWv/Et0/eFSZmh8
rS/cNMLshSOKMbaPvdopUnWhLspUh82wWDNjDFJx2XNlStVpFkMikKtSY4TrtbV+
zzHxZpLyQxc=
=NB0a
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"The main content for 5.15 is a series that cleans up the handling of
strncpy_from_user() and strnlen_user(), removing a lot of slightly
incorrect versions of these in favor of the lib/strn*.c helpers that
implement these correctly and more efficiently.
The only architectures that retain a private version now are mips,
ia64, um and parisc. I had offered to convert those at all, but Thomas
Bogendoerfer wanted to keep the mips version for the moment until he
had a chance to do regression testing.
The branch also contains two patches for bitops and for ffs()"
* tag 'asm-generic-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
bitops/non-atomic: make @nr unsigned to avoid any DIV
asm-generic: ffs: Drop bogus reference to ffz location
asm-generic: reverse GENERIC_{STRNCPY_FROM,STRNLEN}_USER symbols
asm-generic: remove extra strn{cpy_from,len}_user declarations
asm-generic: uaccess: remove inline strncpy_from_user/strnlen_user
s390: use generic strncpy/strnlen from_user
microblaze: use generic strncpy/strnlen from_user
csky: use generic strncpy/strnlen from_user
arc: use generic strncpy/strnlen from_user
hexagon: use generic strncpy/strnlen from_user
h8300: remove stale strncpy_from_user
asm-generic/uaccess.h: remove __strncpy_from_user/__strnlen_user
The arch-specific Kconfig files use HAVE_IDE to indicate if IDE is
supported.
As IDE support and the HAVE_IDE config vanishes with commit b7fb14d3ac
("ide: remove the legacy ide driver"), there is no need to mention
HAVE_IDE in all those arch-specific Kconfig files.
The issue was identified with ./scripts/checkkconfigsymbols.py.
Fixes: b7fb14d3ac ("ide: remove the legacy ide driver")
Suggested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20210728182115.4401-1-lukas.bulwahn@gmail.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Most architectures do not need a custom implementation, and in most
cases the generic implementation is preferred, so change the polariy
on these Kconfig symbols to require architectures to select them when
they provide their own version.
The new name is CONFIG_ARCH_HAS_{STRNCPY_FROM,STRNLEN}_USER.
The remaining architectures at the moment are: ia64, mips, parisc,
um and xtensa. We should probably convert these as well, but
I was not sure how far to take this series. Thomas Bogendoerfer
had some concerns about converting mips but may still do some
more detailed measurements to see which version is better.
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: linux-ia64@vger.kernel.org
Cc: linux-mips@vger.kernel.org
Cc: linux-parisc@vger.kernel.org
Cc: linux-s390@vger.kernel.org
Cc: linux-um@lists.infradead.org
Cc: linux-xtensa@linux-xtensa.org
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Helge Deller <deller@gmx.de> # parisc
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
SYS_SUPPORTS_HUGETLBFS config has duplicate definitions on platforms
that subscribe it. Instead, just make it a generic option which can be
selected on applicable platforms.
Also rename it as ARCH_SUPPORTS_HUGETLBFS instead. This reduces code
duplication and makes it cleaner.
Link: https://lkml.kernel.org/r/1617259448-22529-3-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com> [arm64]
Acked-by: Palmer Dabbelt <palmerdabbelt@google.com> [riscv]
Acked-by: Michael Ellerman <mpe@ellerman.id.au> [powerpc]
Cc: Russell King <linux@armlinux.org.uk>
Cc: Will Deacon <will@kernel.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The kernel test robot reported multiple linkage problems like this:
hppa64-linux-ld: init/main.o(.init.text+0x56c): cannot reach printk
init/main.o: in function `unknown_bootoption':
(.init.text+0x56c): relocation truncated to fit: R_PARISC_PCREL22F against
symbol `printk' defined in .text.unlikely section in kernel/printk/printk.o
There are two ways to solve it:
a) Enable the -mlong-call compiler option (CONFIG_MLONGCALLS),
b) Add long branch stub support in 64-bit linker.
While b) is the long-term solution, this patch works around the issue by
automatically enabling the CONFIG_MLONGCALLS option when
CONFIG_COMPILE_TEST is set, which indicates that a non-production kernel
(e.g. 0-day kernel) is built.
Signed-off-by: Helge Deller <deller@gmx.de>
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 00e35f2b0e ("parisc: Enable -mlong-calls gcc option by default when !CONFIG_MODULES")
Cc: stable@vger.kernel.org # v5.6+
parisc uses -fpatchable-function-entry with dynamic ftrace, which means we
don't need recordmcount. Select FTRACE_MCOUNT_USE_PATCHABLE_FUNCTION_ENTRY
to tell that to the build system.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Fixes: 3b15cdc159 ("tracing: move function tracer options to Kconfig")
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210224225706.2726050-1-samitolvanen@google.com
The irq stack switching was moved out of the ASM entry code in course of
the entry code consolidation. It ended up being suboptimal in various
ways.
- Make the stack switching inline so the stackpointer manipulation is not
longer at an easy to find place.
- Get rid of the unnecessary indirect call.
- Avoid the double stack switching in interrupt return and reuse the
interrupt stack for softirq handling.
- A objtool fix for CONFIG_FRAME_POINTER=y builds where it got confused
about the stack pointer manipulation.
-----BEGIN PGP SIGNATURE-----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=Sqr1
-----END PGP SIGNATURE-----
Merge tag 'x86-entry-2021-02-24' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 irq entry updates from Thomas Gleixner:
"The irq stack switching was moved out of the ASM entry code in course
of the entry code consolidation. It ended up being suboptimal in
various ways.
This reworks the X86 irq stack handling:
- Make the stack switching inline so the stackpointer manipulation is
not longer at an easy to find place.
- Get rid of the unnecessary indirect call.
- Avoid the double stack switching in interrupt return and reuse the
interrupt stack for softirq handling.
- A objtool fix for CONFIG_FRAME_POINTER=y builds where it got
confused about the stack pointer manipulation"
* tag 'x86-entry-2021-02-24' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Fix stack-swizzle for FRAME_POINTER=y
um: Enforce the usage of asm-generic/softirq_stack.h
x86/softirq/64: Inline do_softirq_own_stack()
softirq: Move do_softirq_own_stack() to generic asm header
softirq: Move __ARCH_HAS_DO_SOFTIRQ to Kconfig
x86: Select CONFIG_HAVE_IRQ_EXIT_ON_IRQ_STACK
x86/softirq: Remove indirection in do_softirq_own_stack()
x86/entry: Use run_sysvec_on_irqstack_cond() for XEN upcall
x86/entry: Convert device interrupts to inline stack switching
x86/entry: Convert system vectors to irq stack macro
x86/irq: Provide macro for inlining irq stack switching
x86/apic: Split out spurious handling code
x86/irq/64: Adjust the per CPU irq stack pointer by 8
x86/irq: Sanitize irq stack tracking
x86/entry: Fix instrumentation annotation
Pull parisc updates from Helge Deller:
- Optimize parisc page table locks by using the existing
page_table_lock
- Export argv0-preserve flag in binfmt_misc for usage in qemu-user
- Fix interrupt table (IVT) checksum so firmware will call crash
handler (HPMC)
- Increase IRQ stack to 64kb on 64-bit kernel
- Switch to common devmem_is_allowed() implementation
- Minor fix to get_whan()
* 'parisc-5.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
binfmt_misc: pass binfmt_misc flags to the interpreter
parisc: Optimize per-pagetable spinlocks
parisc: Replace test_ti_thread_flag() with test_tsk_thread_flag()
parisc: Bump 64-bit IRQ stack size to 64 KB
parisc: Fix IVT checksum calculation wrt HPMC
parisc: Use the generic devmem_is_allowed()
parisc: Drop out of get_whan() if task is running again
The "oprofile" user-space tools don't use the kernel OPROFILE support any more,
and haven't in a long time. User-space has been converted to the perf
interfaces.
The dcookies stuff is only used by the oprofile code. Now that oprofile's
support is getting removed from the kernel, there is no need for dcookies as
well.
Remove kernel's old oprofile and dcookies support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=I2Ac
-----END PGP SIGNATURE-----
Merge tag 'oprofile-removal-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/linux
Pull oprofile and dcookies removal from Viresh Kumar:
"Remove oprofile and dcookies support
The 'oprofile' user-space tools don't use the kernel OPROFILE support
any more, and haven't in a long time. User-space has been converted to
the perf interfaces.
The dcookies stuff is only used by the oprofile code. Now that
oprofile's support is getting removed from the kernel, there is no
need for dcookies as well.
Remove kernel's old oprofile and dcookies support"
* tag 'oprofile-removal-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/linux:
fs: Remove dcookies support
drivers: Remove CONFIG_OPROFILE support
arch: xtensa: Remove CONFIG_OPROFILE support
arch: x86: Remove CONFIG_OPROFILE support
arch: sparc: Remove CONFIG_OPROFILE support
arch: sh: Remove CONFIG_OPROFILE support
arch: s390: Remove CONFIG_OPROFILE support
arch: powerpc: Remove oprofile
arch: powerpc: Stop building and using oprofile
arch: parisc: Remove CONFIG_OPROFILE support
arch: mips: Remove CONFIG_OPROFILE support
arch: microblaze: Remove CONFIG_OPROFILE support
arch: ia64: Remove rest of perfmon support
arch: ia64: Remove CONFIG_OPROFILE support
arch: hexagon: Don't select HAVE_OPROFILE
arch: arc: Remove CONFIG_OPROFILE support
arch: arm: Remove CONFIG_OPROFILE support
arch: alpha: Remove CONFIG_OPROFILE support
Pull ELF compat updates from Al Viro:
"Sanitizing ELF compat support, especially for triarch architectures:
- X32 handling cleaned up
- MIPS64 uses compat_binfmt_elf.c both for O32 and N32 now
- Kconfig side of things regularized
Eventually I hope to have compat_binfmt_elf.c killed, with both native
and compat built from fs/binfmt_elf.c, with -DELF_BITS={64,32} passed
by kbuild, but that's a separate story - not included here"
* 'work.elf-compat' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
get rid of COMPAT_ELF_EXEC_PAGESIZE
compat_binfmt_elf: don't bother with undef of ELF_ARCH
Kconfig: regularize selection of CONFIG_BINFMT_ELF
mips compat: switch to compat_binfmt_elf.c
mips: don't bother with ELF_CORE_EFLAGS
mips compat: don't bother with ELF_ET_DYN_BASE
mips: KVM_GUEST makes no sense for 64bit builds...
mips: kill unused definitions in binfmt_elf[on]32.c
mips binfmt_elf*32.c: use elfcore-compat.h
x32: make X32, !IA32_EMULATION setups able to execute x32 binaries
[amd64] clean PRSTATUS_SIZE/SET_PR_FPVALID up properly
elf_prstatus: collect the common part (everything before pr_reg) into a struct
binfmt_elf: partially sanitize PRSTATUS_SIZE and SET_PR_FPVALID
On parisc a spinlock is stored in the next page behind the pgd which
protects against parallel accesses to the pgd. That's why one additional
page (PGD_ALLOC_ORDER) is allocated for the pgd.
Matthew Wilcox suggested that we instead should use a pointer in the
struct page table for this spinlock and noted, that the comments for the
PGD_ORDER and PMD_ORDER defines were wrong.
Both suggestions are addressed with this patch. Instead of having an own
spinlock to protect the pgd, we now switch to use the existing
page_table_lock. Additionally, beside loading the pgd into cr25 in
switch_mm_irqs_off(), the physical address of this lock is loaded into
cr28 (tr4), so that we can avoid implementing a complicated lookup in
assembly for this lock in the TLB fault handlers.
The existing Hybrid L2/L3 page table scheme (where the pmd is adjacent
to the pgd) has been dropped with this patch.
Remove the locking in set_pte() and the huge-page pte functions too.
They trigger a spinlock recursion on 32bit machines and seem unnecessary.
Suggested-by: Matthew Wilcox <willy@infradead.org>
Fixes: b37d1c1898 ("parisc: Use per-pagetable spinlock")
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Merge in the recent paravirt changes to resolve conflicts caused
by objtool annotations.
Conflicts:
arch/x86/xen/xen-asm.S
Signed-off-by: Ingo Molnar <mingo@kernel.org>
To prepare for inlining do_softirq_own_stack() replace
__ARCH_HAS_DO_SOFTIRQ with a Kconfig switch and select it in the affected
architectures.
This allows in the next step to move the function prototype and the inline
stub into a seperate asm-generic header file which is required to avoid
include recursion.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210210002513.181713427@linutronix.de
Helge Deller