AR9382 needs to be configured for the correct chain mask before
running AGC/TxIQ caliberation. Otherwise reset would fail.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The calibration actual calibration flags are only used by the per chip family
source files, so it makes more sense to define them in those files instead
of globally. That way the code has to test for less flags.
Also instead of using a separate callback for testing whether a particular
calibration type is supported, simply adjust ah->supp_cals in the calibration
init which is called right after the hardware reset, before any of the
calibrations are run.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The percal struct and bitmask for the initial DC calibration are not
used anywhere, so they can be removed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The noise floor history buffer is currently not kept per channel, which
can lead to problems when changing channels from a clean channel to a
noisy one. Also when switching from HT20 to HT40, the noise floor
history buffer is full of measurements, but none of them contain data
for the extension channel, which it needs quite a bit of time to recover
from.
This patch puts all the per-channel calibration data into a single data
structure, and gives the the driver control over whether that is used
per-channel or even not used for some channels.
For ath9k_htc, I decided to keep this per-channel in order to avoid
creating regressions.
For ath9k, the data is kept only for the operating channel, which saves
some space. ath9k_hw takes care of wiping old data when the operating
channel or its channel flags change.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The periodic noise floor calibration is broken on this chip family, because
it keeps triggering a software-filtered noise floor calibration, but never
reads the result before uploading the history buffer value to the hardware.
Fix this with a call to ath9k_hw_getnf(), just like on AR9002.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On AR9003 the initial noise floor calibration is currently triggered
at the end of the reset without allowing the hardware to update the
baseband settings. This could potentially make scans in noisy
environments a bit more unreliable, so use the same calibration
sequence that is used on AR9002.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To enable it we now disable and re-enable the PHY chips
after TX IQ calibration.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes from drivers/net/ all the unnecessary
return; statements that precede the last closing brace of
void functions.
It does not remove the returns that are immediately
preceded by a label as gcc doesn't like that.
It also does not remove null void functions with return.
Done via:
$ grep -rP --include=*.[ch] -l "return;\n}" net/ | \
xargs perl -i -e 'local $/ ; while (<>) { s/\n[ \t\n]+return;\n}/\n}/g; print; }'
with some cleanups by hand.
Compile tested x86 allmodconfig only.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable TX IQ calibration, it was prematurely enabled in
previous versions.
Cc: Paul Shaw <Paul.Shaw@Atheros.com>
Cc: Thomas Hammel <Thomas.Hammel@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This goes with some new shiny TX IQ calibration that AR9003
hardware family supports.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is the last call on calib.c which acceses PHY stuff,
with this change we calib.c is now generic between both
all supported hardware families.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calibration code touches phy registers and since these
change the calibration code needs to be abstracted.
Noise floor calibration is the only thing remaining but
since the remaining calls only touch the AR_PHY_AGC_CONTROL
register we'll just define that register conditionally, that
will be done separately. The goal is to remove the dependency
of ar9002_phy.h on calib.c
This also adds stubs to be filled for AR9003 calibration code.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Senthil Balasubramanian