All IRQs that can be used to wake up the system must be routed through
r_intc, so they are visible to firmware while the system is suspended.
In addition to the external NMI input, which is already routed through
r_intc, these include PIO and R_PIO (gpio-keys), the LRADC, and the RTC.
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The binding of R_INTC was updated to allow specifying interrupts other
than the external NMI, since routing those interrupts through the R_INTC
driver allows using them for wakeup.
Update the device trees to use the new binding.
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The empty CSI port triggers a dt-validate warning. Let's align with the
other DTSI and remove it entirely, expecting the DTS to fill it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20210114113538.1233933-14-maxime@cerno.tech
The A83T SoC contains a message box that can be used to send messages
and interrupts back and forth between the ARM application CPUs and the
ARISC coprocessor. Add a device tree node for it.
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Most of the commits are for additional hardware support and minor fixes
for existing machines for all the usual platforms: qcom, amlogic, at91,
gemini, mediatek, ti, socfpga, i.mx, layerscape, uniphier, rockchip,
exynos, ux500, mvebu, tegra, stm32, renesas, sunxi, broadcom, omap,
and versatile.
The conversion of binding files to machine-readable yaml format
continues, along with fixes found during the validation.
Andre Przywara takes over maintainership for the old Calxeda Highbank
platform and provides a number of updates.
The OMAP2+ platforms see a continued move from platform data into
dts files, for many devices that relied on a mix of auxiliary data
in addition to the DT description
A moderate number of new SoCs and machines are added, here is a full
list:
- Two new Qualcomm SoCs with their evaluation boards: Snapdragon 865
(SM8250) is the current high-end phone chip, and IPQ6018 is a new
WiFi-6 router chip.
- Mediatek MT8516 application processor SoC for voice assistants, along
with the "pumpkin" development board
- NXP i.MX8M Plus SoC, a variant of the popular i.MX8M, along with an
evaluation board.
- Kontron "sl28" board family based on NXP LS1028A
- Eleven variations of the new i.MX6 TechNexion Pico board, combining
the "dwarf", "hobbit", "nymph" and "pi" baseboards with i.MX6/i.MX7
SoM carriers
- Three additional variants of the Toradex Colibri board family, all
based on versions of the NXP i.MX7.
- The Pinebook Pro laptop based on Rockchip RK3399
- Samsung S7710 Galaxy Xcover 2, a 2013 vintage Android phone based on
the ST-Ericsson u8500 platform
- DH Electronics DHCOM SoM and PDK2 rev. 400 carrier based on
STMicroelectronics stm32mp157
- Renesas M3ULCB starter kit for R-Car M3-W+
- Hoperun HiHope development board with Renesas RZ/G2M
- Pine64 PineTab tablet and PinePhone phone, both based on Allwinner A64
- Linutronix Testbox v2 for the Lamobo R1 router, based on Allwinner A20
- PocketBook Touch Lux 3 ebook reader, based on Allwinner A13
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=ye2F
-----END PGP SIGNATURE-----
Merge tag 'arm-dt-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM devicetree updates from Arnd Bergmann:
"Most of the commits are for additional hardware support and minor
fixes for existing machines for all the usual platforms: qcom,
amlogic, at91, gemini, mediatek, ti, socfpga, i.mx, layerscape,
uniphier, rockchip, exynos, ux500, mvebu, tegra, stm32, renesas,
sunxi, broadcom, omap, and versatile.
The conversion of binding files to machine-readable yaml format
continues, along with fixes found during the validation. Andre
Przywara takes over maintainership for the old Calxeda Highbank
platform and provides a number of updates.
The OMAP2+ platforms see a continued move from platform data into dts
files, for many devices that relied on a mix of auxiliary data in
addition to the DT description
A moderate number of new SoCs and machines are added, here is a full
list:
- Two new Qualcomm SoCs with their evaluation boards: Snapdragon 865
(SM8250) is the current high-end phone chip, and IPQ6018 is a new
WiFi-6 router chip.
- Mediatek MT8516 application processor SoC for voice assistants,
along with the "pumpkin" development board
- NXP i.MX8M Plus SoC, a variant of the popular i.MX8M, along with an
evaluation board.
- Kontron "sl28" board family based on NXP LS1028A
- Eleven variations of the new i.MX6 TechNexion Pico board, combining
the "dwarf", "hobbit", "nymph" and "pi" baseboards with i.MX6/i.MX7
SoM carriers
- Three additional variants of the Toradex Colibri board family, all
based on versions of the NXP i.MX7.
- The Pinebook Pro laptop based on Rockchip RK3399
- Samsung S7710 Galaxy Xcover 2, a 2013 vintage Android phone based
on the ST-Ericsson u8500 platform
- DH Electronics DHCOM SoM and PDK2 rev. 400 carrier based on
STMicroelectronics stm32mp157
- Renesas M3ULCB starter kit for R-Car M3-W+
- Hoperun HiHope development board with Renesas RZ/G2M
- Pine64 PineTab tablet and PinePhone phone, both based on Allwinner
A64
- Linutronix Testbox v2 for the Lamobo R1 router, based on Allwinner
A20
- PocketBook Touch Lux 3 ebook reader, based on Allwinner A13"
* tag 'arm-dt-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (520 commits)
ARM: dts: ux500: Fix missing node renames
arm64: dts: Revert "specify console via command line"
MAINTAINERS: Update Calxeda Highbank maintainership
arm: dts: calxeda: Group port-phys and sgpio-gpio items
arm: dts: calxeda: Fix interrupt grouping
arm: dts: calxeda: Provide UART clock
arm: dts: calxeda: Basic DT file fixes
arm64: dts: specify console via command line
ARM: dts: at91: sama5d27_wlsom1_ek: add USB device node
ARM: dts: gemini: Add thermal zone to DIR-685
ARM: dts: gemini: Rename IDE nodes
ARM: socfpga: arria10: Add ptp_ref clock to ethernet nodes
arm64: dts: ti: k3-j721e-mcu: add scm node and phy-gmii-sel nodes
arm64: dts: ti: k3-am65-mcu: add phy-gmii-sel node
arm64: dts: ti: k3-am65-mcu: Add DMA entries for ADC
arm64: dts: ti: k3-am65-main: Add DMA entries for main_spi0
arm64: dts: ti: k3-j721e-mcu-wakeup: Add DMA entries for ADC
arm64: dts: ti: k3-am65: Add clocks to dwc3 nodes
arm64: dts: meson-g12b-odroid-n2: add SPIFC controller node
arm64: dts: khadas-vim3: add SPIFC controller node
...
This enables passive cooling by down-regulating CPU voltage
and frequency.
For the trip points, I used values from the BSP code directly.
The critical trip point value is 30°C above the maximum recommended
ambient temperature (70°C) for the SoC from the datasheet, so there's
some headroom even at such a high ambient temperature.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
When the raw numbers used for clk and reset indices in the EMAC device
node were converted to the new macros, the order of the clk and reset
properties was overlooked, and thus the incorrect macros were used.
This results in the EMAC being non-responsive, as well as an oops due
to incorrect usage of the reset control.
Correct the macro types, and also reorder the clk and reset properties
to match all the other device nodes.
Fixes: 765866edb1 ("ARM: dts: sunxi: Use macros for references to CCU clocks")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
A few clocks from the CCU were exported later, and references to them in
the device tree were using raw numbers.
Now that the DT binding header changes are in as well, switch to the
macros for more clarity.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
There are three sensors, two for each CPU cluster, one for GPU.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The Security System is a hardware cryptographic accelerator that support
AES/MD5/SHA1/DES/3DES/PRNG/RSA algorithms.
It could be found on Allwinner SoC A80 and A83T
This patch adds it on the Allwinner A83T SoC Device-tree.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
This reverts commits 3d109bdca9 ("ARM: dts: sunxi: Remove useless
phy-names from EHCI and OHCI"), 0a3df8bb6d ("ARM: dts: sunxi: h3/h5:
Remove useless phy-names from EHCI and OHCI") and 3c7ab90aaa ("arm64:
dts: allwinner: Remove useless phy-names from EHCI and OHCI").
It turns out that while the USB bindings were not mentionning it, the PHY
client bindings were mandating that phy-names is set when phys is. Let's
add it back.
Fixes: 3d109bdca9 ("ARM: dts: sunxi: Remove useless phy-names from EHCI and OHCI")
Fixes: 0a3df8bb6d ("ARM: dts: sunxi: h3/h5: Remove useless phy-names from EHCI and OHCI")
Fixes: 3c7ab90aaa ("arm64: dts: allwinner: Remove useless phy-names from EHCI and OHCI")
Reported-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20191002112651.100504-1-mripard@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unlike the A10 that has 6 timers available, the A83t has only two, with
only two interrupts, just like the A23. Let's change the compatible to
reflect that.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Since A31, memory mapping of the IR driver has changed.
Prefer the A31 bindings instead of A13.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Acked-by: Sean Young <sean@mess.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Even though the binding mentions that the PHY name must be "phy", it turns
out that all our DTs had "hdmi-phy" instead.
The code doesn't care about the phy-names property, so we can just change
our DTs to match the binding, without any side effect.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The DE2 bus takes two clocks, named bus and mod according to the binding.
However, the order of these clocks change from one SoC to another. Even
though it might not be an issue in most cases, having consistency will help
if we ever need to have some code to deal with deprecated bindings, and in
general it's just better.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A83T SoC has a camera sensor interface (known as CSI in Allwinner
lingo), which is similar to the one found on the A64 and H3. The only
difference seems to be that support of MIPI CSI through a connected
MIPI CSI-2 bridge.
Add a device node for it, and pinctrl nodes for the commonly used MCLK
and 8-bit parallel interface. The property /omit-if-no-ref/ is added to
the pinctrl nodes to keep the device tree blob size down if they are
unused.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Neither the OHCI or EHCI bindings are using the phy-names property, so we
can just drop it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
I2C2 is available on the PE pingroup, on the same pins as the camera
sensor interface (CSI) controller's camera control interface pins.
This provides an option to use I2C2 instead of that control interface
to configure camera sensors.
Add a pinctrl node for it. The property /omit-if-no-ref/ is added to
keep the device tree blob size down if it is unused.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner A83T SoC has a low res adc like the one in Allwinner A10 SoC.
Now the driver has been modified to support it.
Add support for it.
Signed-off-by: Ziping Chen <techping.chan@gmail.com>
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
A83T DTSI has cpu clocks defined only on the first CPU in each cluster.
We can bring down any CPU in the cluster, so we need to define clock
for each CPU, so that the system knows what clock to use if the first
CPU is down.
Also move the clocks property below the compatible on cpus where it is
already defined. Property "clock-names" is not needed.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add pin definitions for UART2 PB pins. These are used on TBS-A711
tablet.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Enable to use CPUs as cooling device in the future, by adding
"#cooling-cells" to each CPU node. This property should be present for
all the CPUs of a cluster. If these are present only for a subset of
CPUs of a cluster then things will start falling apart as soon as the
CPUs are brought online in a different order. For example, this will
happen because the operating system looks for such properties in the CPU
node it is trying to bring up, so that it can register a cooling device.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
A83T has 5 UART interfaces, but only the first two have their nodes
defined in sun8i-a83t.dtsi. Add nodes for the missing interfaces.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The USB OTG binding we have mandates to have a dr_mode property, yet not
all boards are setting it.
Since the generic otg binding states that the default mode should be the
OTG mode, let's use that one in our DTSI.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Even though we shouldn't really have any external user of the clock
provided by the TCON, if clock-output-names is set, then #clock-cells must
be there as well.
Fix this.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
As can be shown by the YAML schema now, the combination of GIC compatibles
we were using has never been an option.
Switch to the gic-400 variant, which is the more correct option.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Our display engine endpoints trigger some DTC warnings due to the fact that
we're having a single endpoint that doesn't need any reg property, and
since we don't have a reg property, we don't need the address-cells and
size-cells properties anymore.
Fix those
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Unlike what the binding for multiple pipeline documents, the A83t doesn't
have the cross links between the TCON and the mixers.
Let's add them.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Our memory node will generate a warning in DTC since the unit address is
not matching the reg property. However, that node will be created by the
bootloader, so we can just remove it entirely in order to remove that
warning.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The cir interface is like on the H3 located at 0x01f02000 and is exactly
the same. This patch adds support for the ir interface on the A83T.
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The CIR Pin of the A83T is located at PL12.
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
ddress-cells/size-cells is unnecessary for dwmac-sun8i node.
It was in early days, but since a mdio node is used, it could be
removed.
This patch fix the following DT warning:
Warning (avoid_unnecessary_addr_size): /soc/ethernet@1c50000: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add the use of enable-method property for SMP support which allows
to handle the SMP support for this specific SoC.
This commit adds enable-method properties to all CPU nodes.
Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The R_CPUCFG is a collection of registers needed for SMP bringup
on clusters and cluster's reset.
For the moment, documentation about this register is found in
Allwinner's code only.
Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
As we found in sun9i-a80, CPUCFG is a collection of registers that are
mapped to the SoC's signals from each individual processor core and
associated peripherals.
These registers are used for SMP bringup and CPU hotplugging.
Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner a83t has a 1 KB sid block with efuse for security rootkey and thermal
calibration data, add node to describe it.
a83t-sid is not currently supported by nvmem/sunxi-sid, but it is
supported in an external driver for FreeBSD.
Signed-off-by: Kyle Evans <kevans@FreeBSD.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Allwinner A83T is an octacore A7 divided in two clusters of 4 A7,
each cluster having its own regulator and clock.
The operating points were found in Allwinner BSP and fex files.
Note that there are a few OPPs that are missing:
1608000000Hz with 920000mV
1800000000Hz with 1000000mV
2016000000Hz with 1080000mV
These OPPs are pretty unstable but it might be due to the SoC quickly
overheating (till the board completely shuts down).
It seems impossible to reach those frequencies with none or passive
cooling, so better leave them out by default.
It's still possible to add those OPPs on a per-board basis though.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
[maxime: Reordered the nodes alphabetically]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Allwinner A83T is a SoC with two clusters of 4 A7, each cluster
having its own regulator and clock.
The regulators are board-specific, thus we need labels for cpu0 and
cpu100 so that we can use references to these nodes from the board
header file.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This commit adds all bits necessary for HDMI on A83T - mixer1, tcon1,
hdmi, hdmi phy and hdmi pinctrl entries.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A83T has an LVDS bus that can be connected to a panel or a bridge. Add
the pinctrl group for it.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A83T has the same PWM block than the H3. Add it to our DT.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The display pipeline on the A83T is mainly composed of the mixers and
TCONs, plus various encoders.
Let's add the first mixer and TCON to the DTSI since the only board I have
can use only the LVDS output on the first TCON. The other parts will be
added eventually.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A83T has 3 I2C controllers under the standard bus. There is one
more in the R_ block section. The pin functions for the 3 controllers
are on PH 0~6. I2C2 can also be used on pins PE14 and PE15, but these
pins can also mux the CSI (camera sensor interface) controller's
embedded I2C controller. The latter seems to be preferred in the
reference designs for I2C camera sensor access, freeing I2C2 for other
uses.
This patch adds device nodes for the three standard I2C controllers,
as well as pinmux settings for the PH pins. For I2C0 and I2C1, since
they only have one possible setting, just set them by default.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A83T has 3 I2S controllers. The first is multiplexed with the TDM
controller. The pins are generally connected to the codec side of the
AXP81x PMIC/codec/RTC chip. The second is free for other uses. The
third only supports output, and is connected internally to the HDMI
controller for HDMI audio output.
This patch adds device nodes for the controllers, and a default pinmux
setting for the second controller.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The dwmac-sun8i is an ethernet MAC hardware that support 10/100/1000 speed.
This patch add support for it on the Allwinner a83t SoC Device-tree.
This patch add the emac device node and the related RGMII pins node.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
mmc1 only has 1 possible pinmux setting.
Move any settings to the dtsi file and set it by default.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Samuel Holland