R-Car series gpio_rcar driver can control GPIO IRQ today.
It needs base IRQ number for gpio_rcar_config :: .irq_base
This patch adds macro for GPIO IRQ.
This patch was tested on Bock-W board
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
We need three steps to prepare for the new Armadillo reference DT board code:
- Split the device list into r8a7740_early_devices used by the old platform
data setup (board-armadillo.c) and r8a7740_devices_dt used by both
setup variants.
- Introduce new r8a7740_init_delay() to be more flexible about calling
shmobile_setup_delay().
- For the generic r8a7740 support, we switch to device tree setup for
the GIC, the irqpin devices and the I2C controllers.
This is slightly similar to commit 3b00f93426
"ARM: shmobile: sh73a0: Do not use early devices with DT reference"
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
We add a variant to initalize the interrupt controller in case we describe
the GIC using the Device Tree and not platform data.
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This is the third and smallest of the SoC specific updates.
Changes include:
* SMP support for the Xilinx zynq platform
* Smaller imx changes
* LPAE support for mvebu
* Moving the orion5x, kirkwood, dove and mvebu platforms
to a common "mbus" driver for their internal devices.
It would be good to get feedback on the location of the "mbus"
driver. Since this is used on multiple platforms may potentially
get shared with other architectures (powerpc and arm64), it
was moved to drivers/bus/. We expect other similar drivers to
get moved to the same place in order to avoid creating more
top-level directories under drivers/ or cluttering up the
messy drivers/misc/ even more.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=rQsu
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates (part 3) from Arnd Bergmann:
"This is the third and smallest of the SoC specific updates. Changes
include:
- SMP support for the Xilinx zynq platform
- Smaller imx changes
- LPAE support for mvebu
- Moving the orion5x, kirkwood, dove and mvebu platforms to a common
"mbus" driver for their internal devices.
It would be good to get feedback on the location of the "mbus" driver.
Since this is used on multiple platforms may potentially get shared
with other architectures (powerpc and arm64), it was moved to
drivers/bus/. We expect other similar drivers to get moved to the
same place in order to avoid creating more top-level directories under
drivers/ or cluttering up the messy drivers/misc/ even more."
* tag 'soc-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
ARM: imx: reset_controller may be disabled
ARM: mvebu: Align the internal registers virtual base to support LPAE
ARM: mvebu: Limit the DMA zone when LPAE is selected
arm: plat-orion: remove addr-map code
arm: mach-mv78xx0: convert to use the mvebu-mbus driver
arm: mach-orion5x: convert to use mvebu-mbus driver
arm: mach-dove: convert to use mvebu-mbus driver
arm: mach-kirkwood: convert to use mvebu-mbus driver
arm: mach-mvebu: convert to use mvebu-mbus driver
ARM i.MX53: set CLK_SET_RATE_PARENT flag on the tve_ext_sel clock
ARM i.MX53: tve_di clock is not part of the CCM, but of TVE
ARM i.MX53: make tve_ext_sel propagate rate change to PLL
ARM i.MX53: Remove unused tve_gate clkdev entry
ARM i.MX5: Remove tve_sel clock from i.MX53 clock tree
ARM: i.MX5: Add PATA and SRTC clocks
ARM: imx: do not bring up unavailable cores
ARM: imx: add initial imx6dl support
ARM: imx1: mm: add call to mxc_device_init
ARM: imx_v4_v5_defconfig: Add CONFIG_GPIO_SYSFS
ARM: imx_v6_v7_defconfig: Select CONFIG_PERF_EVENTS
...
These patches are all for Renesas shmobile, and depend on the earlier
pinctrl updates. Remarkably, this adds support for three new SoCs:
r8a73a4, r8a73a4 and r8a7778. The bulk of the code added for these is
for pinctrl (using the new subsystem) and for clocks (not yet using the
common clock subsystem). The latter will have to get converted in one
of the upcoming releases, but shmobile is not ready for that yet.
The series also contains Renesas shmobile board changes, adding one
board file for each of the three new SoCs. These boards are using a
mix of classic and device-tree based probing, as there is still a lot of
infrastructure in shmobile that has not been converted to DT yet. Once
those are resolved to the degree that no board specific setup code is
needed, they can get folded into the respective SoC setup files.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=xaLf
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates (part 2) from Arnd Bergmann:
"These patches are all for Renesas shmobile, and depend on the earlier
pinctrl updates. Remarkably, this adds support for three new SoCs:
r8a73a4, r8a73a4 and r8a7778. The bulk of the code added for these is
for pinctrl (using the new subsystem) and for clocks (not yet using
the common clock subsystem). The latter will have to get converted in
one of the upcoming releases, but shmobile is not ready for that yet.
The series also contains Renesas shmobile board changes, adding one
board file for each of the three new SoCs. These boards are using a
mix of classic and device-tree based probing, as there is still a lot
of infrastructure in shmobile that has not been converted to DT yet.
Once those are resolved to the degree that no board specific setup
code is needed, they can get folded into the respective SoC setup files."
* tag 'soc-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (78 commits)
ARM: shmobile: use r8a7790 timer setup code on Lager
ARM: shmobile: force enable of r8a7790 arch timer
ARM: shmobile: Add second I/O range for r8a7790 PFC
ARM: shmobile: bockw: enable network settings on bootargs
ARM: shmobile: bockw: add SMSC ethernet support
ARM: shmobile: R8A7778: add Ether support
ARM: shmobile: bockw: enable SMSC ethernet on defconfig
ARM: shmobile: r8a7778: add r8a7778_init_irq_extpin()
ARM: shmobile: r8a7778: remove pointless PLATFORM_INFO()
ARM: shmobile: mackerel: clean up MMCIF vs. SDHI1 selection
ARM: shmobile: mackerel: add interrupt names for SDHI0
ARM: shmobile: mackerel: switch SDHI and MMCIF interfaces to slot-gpio
ARM: shmobile: mackerel: remove OCR masks, where regulators are used
ARM: shmobile: mackerel: SDHI resources do not have to be numbered
ARM: shmobile: Initial r8a7790 Lager board support
ARM: shmobile: APE6EVM LAN9220 support
ARM: shmobile: APE6EVM PFC support
ARM: shmobile: APE6EVM base support
ARM: shmobile: kzm9g-reference: add ethernet support
ARM: shmobile: add R-Car M1A Bock-W platform support
...
This is yet another driver change, which is split out just because
of its size. As already in 3.9, a lot of changes are going on here,
as the shmobile platform gets converted from its own pin control
API to the generic drivers/pinctrl subsystem.
Based on agreements with Paul Mundt, we are merging the sh-arch-side
changes here as well.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=9DPk
-----END PGP SIGNATURE-----
Merge tag 'renesas-pinctrl-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC pinctrl changes for Renesas from Olof Johansson:
"This is yet another driver change, which is split out just because of
its size. As already in 3.9, a lot of changes are going on here, as
the shmobile platform gets converted from its own pin control API to
the generic drivers/pinctrl subsystem.
Based on agreements with Paul Mundt, we are merging the sh-arch-side
changes here as well"
* tag 'renesas-pinctrl-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (142 commits)
ARM: shmobile: r8a7779: Remove INTC function GPIOs
ARM: shmobile: r8a7779: Remove LBSC function GPIOs
ARM: shmobile: r8a7779: Remove USB function GPIOs
ARM: shmobile: r8a7779: Remove HSPI function GPIOs
ARM: shmobile: r8a7779: Remove SCIF function GPIOs
ARM: shmobile: r8a7779: Remove SDHI and MMCIF function GPIOs
ARM: shmobile: r8a7779: Remove DU function GPIOs
ARM: shmobile: r8a7779: Remove DU1_DOTCLKOUT1 GPIO
ARM: shmobile: r8a7740: Remove SDHI and MMCIF function GPIOs
ARM: shmobile: r8a7740: Remove LCD0 and LCD1 function GPIOs
ARM: shmobile: sh73a0: Remove IrDA function GPIOs
ARM: shmobile: sh73a0: Remove USB function GPIOs
ARM: shmobile: sh73a0: Remove BSC function GPIOs
ARM: shmobile: sh73a0: Remove KEYSC function GPIOs
ARM: shmobile: sh73a0: Remove pull-up function GPIOS
ARM: shmobile: sh73a0: Remove FSI function GPIOs
ARM: shmobile: sh73a0: Remove I2C function GPIOs
ARM: shmobile: sh73a0: Remove SCIFA and SCIFB function GPIOs
ARM: shmobile: sh73a0: Remove LCDC and LCDC2 function GPIOs
ARM: shmobile: sh7372: Remove SDHI and MMCIF function GPIOs
...
This is a rather large set of patches for device drivers that for one
reason or another the subsystem maintainer preferred to get merged
through the arm-soc tree. There are both new drivers as well as
existing drivers that are getting converted from platform-specific
code into standalone drivers using the appropriate subsystem
specific interfaces.
In particular, we can now have pinctrl, clk, clksource and irqchip
drivers in one file per driver, without the need to call into
platform specific interface, or to get called from platform specific
code, as long as all information about the hardware is provided
through a device tree.
Most of the drivers we touch this time are for clocksource. Since
now most of them are part of drivers/clocksource, I expect that we
won't have to touch these again from arm-soc and can let the
clocksource maintainers take care of these in the future.
Another larger part of this series is specific to the exynos platform,
which is seeing some significant effort in upstreaming and
modernization of its device drivers this time around, which
unfortunately is also the cause for the churn and a lot of the
merge conflicts.
There is one new subsystem that gets merged as part of this series:
the reset controller interface, which is a very simple interface
for taking devices on the SoC out of reset or back into reset.
Patches to use this interface on i.MX follow later in this merge
window, and we are going to have other platforms (at least tegra
and sirf) get converted in 3.11. This will let us get rid of
platform specific callbacks in a number of platform independent
device drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJRhKUsAAoJEIwa5zzehBx3Ug4P/RqEen15hxS/NY8SIVRAU5c0
G9ZiSPcLmvXGR/t1RZFeLWKaKOYRb2oW1EbXrlkddprkmg85RuQE/KMpCgzPPhVC
Yrs8UaagMGblaLOjwavVjin/CUXZokRdMfsQoIyMGOezmVGFnv4d4Kt64IOf35DF
24vDv/QO0BAI9k6m6WLqlWvSshb0IkW8r2LneRLnMEAVop7b1xkOxz0sR6l0LWfV
6JAMXyTjJMg0t8uCVW/QyNdxcxINHhV4SYcNkzF3EZ7ol50OiJsT9fg0XW759+Wb
vlX6Xuehg+CBOg+g3ZOZuR8JOEkOhAGRSzuJkk/TmLCCxc+ghnuYz8HArxh6GMHK
KaxvogLIi0ZsD94A/BZIKkDtOLWlzdz2HBrYo9PTz8zrOz/gXhwQ3zq0jPccC5E0
S+YYiobCBXepknF9301ti7wGD9VDzI8nmqOKG6tEBrD3xuO+RoBv+z4pBugN4/1C
DlB19gOz60G5kniziL+wlmWER2qXmYrQZqS+s6+B2XoyoETC0Yij3Rck5vyC6qIK
A2sni+Y9rzNOB9nzmnISP/UiGUffCy8AV4DZJjMSl0XkF4cpOXqRVGZ2nGB4tR5q
GTOETcDCo5dvMDKX7Wfrz40CQzO39tnPCddg3OIS93ZwMpCeykIlb1FVL7RcsyF7
3uikzYHlDo3C5pvtJ5TS
=ZWk9
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Olof Johansson:
"This is a rather large set of patches for device drivers that for one
reason or another the subsystem maintainer preferred to get merged
through the arm-soc tree. There are both new drivers as well as
existing drivers that are getting converted from platform-specific
code into standalone drivers using the appropriate subsystem specific
interfaces.
In particular, we can now have pinctrl, clk, clksource and irqchip
drivers in one file per driver, without the need to call into platform
specific interface, or to get called from platform specific code, as
long as all information about the hardware is provided through a
device tree.
Most of the drivers we touch this time are for clocksource. Since now
most of them are part of drivers/clocksource, I expect that we won't
have to touch these again from arm-soc and can let the clocksource
maintainers take care of these in the future.
Another larger part of this series is specific to the exynos platform,
which is seeing some significant effort in upstreaming and
modernization of its device drivers this time around, which
unfortunately is also the cause for the churn and a lot of the merge
conflicts.
There is one new subsystem that gets merged as part of this series:
the reset controller interface, which is a very simple interface for
taking devices on the SoC out of reset or back into reset. Patches to
use this interface on i.MX follow later in this merge window, and we
are going to have other platforms (at least tegra and sirf) get
converted in 3.11. This will let us get rid of platform specific
callbacks in a number of platform independent device drivers."
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (256 commits)
irqchip: s3c24xx: add missing __init annotations
ARM: dts: Disable the RTC by default on exynos5
clk: exynos5250: Fix parent clock for sclk_mmc{0,1,2,3}
ARM: exynos: restore mach/regs-clock.h for exynos5
clocksource: exynos_mct: fix build error on non-DT
pinctrl: vt8500: wmt: Fix checking return value of pinctrl_register()
irqchip: vt8500: Convert arch-vt8500 to new irqchip infrastructure
reset: NULL deref on allocation failure
reset: Add reset controller API
dt: describe base reset signal binding
ARM: EXYNOS: Add arm-pmu DT binding for exynos421x
ARM: EXYNOS: Add arm-pmu DT binding for exynos5250
ARM: EXYNOS: Enable PMUs for exynos4
irqchip: exynos-combiner: Correct combined IRQs for exynos4
irqchip: exynos-combiner: Add set_irq_affinity function for combiner_irq
ARM: EXYNOS: fix compilation error introduced due to common clock migration
clk: exynos5250: Fix divider values for sclk_mmc{0,1,2,3}
clk: exynos4: export clocks required for fimc-is
clk: samsung: Fix compilation error
clk: tegra: fix enum tegra114_clk to match binding
...
This branch contains platform updates for 3.10. Among the highlights:
- Support for the new Atmel Cortex-A5 based platforms (SAMA5D3)
- New support for CSR SiRFatlas6 SoCs
- A handful of updates for NVidia T114 (a.k.a. Tegra 4)
- A bunch of updates for the shmobile platforms
- A handful of updates for davinci
- A few updates for Qualcomm MSM
- Plus a handful of other patches, defconfig updates, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=HXX3
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Olof Johansson:
"This branch contains part 1 of the platform updates for 3.10. Among
the highlights:
- Support for the new Atmel Cortex-A5 based platforms (SAMA5D3)
- New support for CSR SiRFatlas6 SoCs
- A handful of updates for NVidia T114 (a.k.a. Tegra 4)
- A bunch of updates for the shmobile platforms
- A handful of updates for davinci
- A few updates for Qualcomm MSM
- Plus a handful of other patches, defconfig updates, etc."
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (135 commits)
ARM: tegra: pm: fix build error w/o PM_SLEEP
ARM: davinci: ensure global variables are declared
ARM: davinci: sram.c: fix incorrect type in assignment
ARM: davinci: da8xx dt: make file local symbols static
ARM: davinci: da8xx: add remoteproc support
ARM: socfpga: Upgrade clk driver for socfpga to make use of dts clock entries
ARM: socfpga: Add clock entries into device tree
ARM: socfpga: Enable soft reset
ARM: EXYNOS: replace cpumask by the corresponding macro
ARM: EXYNOS: handle properly the return values
ARM: EXYNOS: factor out the idle states
ARM: OMAP4: Enable fix for Cortex-A9 erratas
ARM: OMAP2+: Export SoC information to userspace
ARM: OMAP2+: SoC name and revision unification
ARM: OMAP2+: Move common part of late init into common function
ARM: tegra: pm: remove duplicated include from pm.c
ARM: davinci: da850: override mmc DT node device name
ARM: davinci: da850: add mmc DT entries
mmc: davinci_mmc: add DT support
ARM: SAMSUNG: check processor type before cache restoration in resume
...
Commit 688036b538 removed the function
'shmobile_enter_wfi' but we forgot to remove the definition in the header file.
Note this function is just an alias to 'cpu_do_idle()' wrapped into a cpuidle
function callback prototype which already exists with the default WFI state
and the arm_simple_enter function.
Remove the function prototype.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* Use r8a7790 timer setup code to force the
arch timer to be enabled regardless of the bootloader setting
- This is necessary for the lager board to boot
This pull request is based on:
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git renesas-boards3-for-v3.10
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git renesas-soc-r8a7790-for-v3.10
The merge was made to provide the r8a7790 timer setup code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=7y6e
-----END PGP SIGNATURE-----
Merge tag 'renesas-boards-lager-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/boards2
From Simon Horman:
Renesas ARM based SoC lager board updates for v3.10
* Use r8a7790 timer setup code to force the
arch timer to be enabled regardless of the bootloader setting
- This is necessary for the lager board to boot
This pull request is based on:
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git renesas-boards3-for-v3.10
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git renesas-soc-r8a7790-for-v3.10
The merge was made to provide the r8a7790 timer setup code
* tag 'renesas-boards-lager-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: use r8a7790 timer setup code on Lager
ARM: shmobile: force enable of r8a7790 arch timer
ARM: shmobile: Add second I/O range for r8a7790 PFC
Signed-off-by: Olof Johansson <olof@lixom.net>
* Force architecture timer to be activated regardless of bootloader
- This is necessary for the lager board to boot
* Add second memory range to r8a7790 PFC device
- This is in preparation for further PFC work.
It should not break anything as it is not used yet.
This pull request is based on:
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git renesas-soc2-for-v3.10
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJRZmnuAAoJENfPZGlqN0++6AAP/3edyVpqono4N8ACAKt5EMUN
EOkJdTtsvdmI+1O3kSWNIp3WSaObYzzqGYpmKMZqIjlCzWVgNpazYvTGGPgBCy/B
J3VGmLerTdy6GMX8lr0Xk3/wU6nKVU9j1znwTDXzcaU9Mpo7naHmirrULL2uAiVX
ZJVNIN0P4cz8yWN4MtTz7slWFoR1aHr1GHEE7/PqFiMFWNeCjSI6z7HQYZggSlz5
p4EH0ZwmVs9jBNoP/TniOobUXqYVtTkO4TsAWnhKWnz2VJGSfs1wY7dYq95tX4pZ
ffuaFfrTRE9dY/dJvnbWpyD8iF7VU4XuvqJBdy7U6JWB9HBBRY6mSNFn5MGMLGI1
sf7ndPZDHLkRV67Sg8/znkssBqR/UW1b90b5yK9jSYdfVmm7lX+GupNjLd1eI5Y7
j+RmA5F3s+nwew0Z5Q0PxWTY2RuuykkawHSrryCvxOXTZ3pVzVxrgFACzanISPeZ
gxU7m7ahrDve0UECX1HH2QErdZwPSY02ZZF9fZoOEnOivNI44e/Vhgh2KKgj/C4e
oDASEUVJwi2KiQAnvt7hO8FG7K4CnPMAjDQaABGML9zUiYd7P/qWoyyos0b9XbKR
LN9iqKjRvNxIuraUpkH5qnotfcPmorNdMOz6D6Qlm2hSwk8XTChCMb3E3gCRO5CZ
WiEq+JcSc2r9LxL/hdpj
=qNDI
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc-r8a7790-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc2
From Simon Horman:
Renesas ARM based r8a7790 SoC update for v3.10
* Force architecture timer to be activated regardless of bootloader
- This is necessary for the lager board to boot
* Add second memory range to r8a7790 PFC device
- This is in preparation for further PFC work.
It should not break anything as it is not used yet.
This pull request is based on:
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git renesas-soc2-for-v3.10
* tag 'renesas-soc-r8a7790-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: force enable of r8a7790 arch timer
ARM: shmobile: Add second I/O range for r8a7790 PFC
Signed-off-by: Olof Johansson <olof@lixom.net>
Update to the r8a7778 SoC:
* Add SH Ethernet support
* Add r8a7778_init_irq_extpin() to allow configuration of IRQ0 - IRQ3
- This is a requirement for SMSC ethernet support
* Cleanup: remove PLATFORM_INFO macro
This pull request is based on:
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-soc2-for-v3.10
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=ih3D
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc-r8a7778-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc2
From Simon Horman <horms+renesas@verge.net.au>:
Renesas ARM r8a7778 SoC update for v3.10
Update to the r8a7778 SoC:
* Add SH Ethernet support
* Add r8a7778_init_irq_extpin() to allow configuration of IRQ0 - IRQ3
- This is a requirement for SMSC ethernet support
* Cleanup: remove PLATFORM_INFO macro
This pull request is based on:
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-soc2-for-v3.10
* tag 'renesas-soc-r8a7778-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: R8A7778: add Ether support
ARM: shmobile: r8a7778: add r8a7778_init_irq_extpin()
ARM: shmobile: r8a7778: remove pointless PLATFORM_INFO()
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Update to the r8a7779 SoC:
* Add SH Ethernet support
* Add comment describing clock ratios
This pull request is based on:
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-soc2-for-v3.10
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=YyOX
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc-r8a7779-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc2
From Simon Horman <horms+renesas@verge.net.au>:
Renesas ARM r8a7779 SoC update for v3.10
Update to the r8a7779 SoC:
* Add SH Ethernet support
* Add comment describing clock ratios
This pull request is based on:
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-soc2-for-v3.10
* tag 'renesas-soc-r8a7779-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: R8A7779: add Ether support
ARM: shmobile: r8a7779: add each clocks ratio on comment area
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Implement a SoC-specific timer init function for
r8a7790 that makes sure the architected timer
is started regardless of boot loader setting.
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add Ether clock and platform device for R8A7778 SoC; add a function to register
this device with board-specific platform data.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add Ether clock and platform device for R8A7779 SoC; add a function to register
this device with board-specific platform data.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds r8a7778_init_irq_extpin() for IRQ0 - IRQ3.
But this patch doesn't enable DT settings on r8a7778.dts,
because R8A7778 chip external IRQ depends on
IRQ0 - IRQ3 pin encoding which came from platform board
implementation.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Function GPIOs are not used anymore, and all code use the GPIO numbers
directly. Remove the GPIOs enumeration.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove IRQ pin function GPIOs that have been deprecated by the pinctrl
API.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove SCIF function GPIOs that have been deprecated by the pinctrl API.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r8a73a4 SoC has sparse GPIO numbers. Declare ranges for pin numbers
in the PFC SoC data. Pin numbers shall be used with the GPIO API from
this point on.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add initial PFC support for the r8a73a4 SoC.
At this point only GPIO interface is supported, move to newer interfaces
planned as incremental changes.
Original authors are Morimoto-san with help from Yoshii-san, thanks to
them for the heavy lifting. Adjusted by Magnus to work together with
updated code in drivers/pinctrl.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Takashi Yoshii <takashi.yoshii.zj@renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Function GPIOs are not used anymore, and all code use the GPIO numbers
directly. Remove the GPIOs enumeration.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Conflicts:
drivers/pinctrl/sh-pfc/pfc-r8a7740.c
This merge is to provide r8a73a4 SoC files, which are added in the
soc branch and depended on by r8a73a4 pfc-changes which are to
be added to the pinmux branch.
Add initial support for the r8a7790 SoC including:
- Single Cortex-A15 CPU Core
- GIC
- Architecture timer
No static virtual mappings are used, all the components
make use of ioremap(). DT_MACHINE_START is still wrapped
in CONFIG_USE_OF to match other mach-shmobile code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
There is no reason each CPU's own function has to exist in common.h.
r8a7779_xxx() go to r8a7779.h
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
There is no reason each CPU's own function has to exist in common.h.
r8a7740_xxx() go to r8a7740.h
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
There is no reason each CPU's own function has to exist in common.h.
sh73a0_xxx() go to sh73a0.h
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
There is no reason each CPU's own function has to exist in common.h.
sh7372_xxx() go to sh7372.h
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Renesas chip has many clocks inside,
and some of them are using fixed ratio via parent clock.
Current shmobile clock code is using own divX_recalc function
and divX_clk_ops.
This patch can reduce these code
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add initial support for the R8A7778 R-Car M1A SoC.
No static virtual mappings are used, all the components
make use of ioremap().
DT_MACHINE_START is still wrapped
in CONFIG_USE_OF to match other mach-shmobile code.
It is based on v1.0 datasheet
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
V3 of initial support for the r8a73a4 SoC including:
- Single Cortex-A15 CPU Core
- GIC
- Architecture timer
No static virtual mappings are used, all the components
make use of ioremap(). DT_MACHINE_START is still wrapped
in CONFIG_USE_OF to match other mach-shmobile code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Update the r8a7779 IRQ code to make use of the
INTC External IRQ pin driver for external
interrupt pins IRQ0 -> IRQ3.
The r8a7779 SoC can like older SH SoCs configure
to use the IRQ0 -> IRQ3 signals as individual
interrupts or a combined IRL mode.
Without this patch the r8a7779 SoC code does
not fully support external IRQ pins in individual
IRQ mode. The r8a7779 PFC code does not yet have
gpio_to_irq() support so no need to update such
code.
At this point the DT reference implementations
are not covered. In the future such code shall
tie in the INTC External IRQ pin driver via
DT, so this kind of verbose code is not needed
for the long term DT case.
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the macro irq_pin() to let board-specific code using
platform devices tie in external IRQn pins in a common way.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Those GPIOs have been deprecated by the pinctrl API. They are unused and
unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Those GPIOs have been deprecated by the pinctrl API. They are unused and
unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Those GPIOs have been deprecated by the pinctrl API. They are unused and
unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Those GPIOs have been deprecated by the pinctrl API. They are unused and
unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Those GPIOs have been deprecated by the pinctrl API. They are unused and
unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Those GPIOs have been deprecated by the pinctrl API. They are unused and
unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Those GPIOs have been deprecated by the pinctrl API. They are unused and
unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Those GPIOs have been deprecated by the pinctrl API. They are unused and
unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Those GPIOs have been deprecated by the pinctrl API. They are unused and
unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Those GPIOs have been deprecated by the pinctrl API. They are unused and
unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Those GPIOs have been deprecated by the pinctrl API. They are unused and
unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Those GPIOs have been deprecated by the pinctrl API. They are unused and
unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Those GPIOs have been deprecated by the pinctrl API. They are unused and
unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Those GPIOs have been deprecated by the pinconf API. They are unused and
unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Those GPIOs have been deprecated by the pinctrl API. They are unused and
unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Those GPIOs have been deprecated by the pinctrl API. They are unused and
unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Those GPIOs have been deprecated by the pinctrl API. They are unused and
unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Those GPIOs have been deprecated by the pinctrl API. They are unused and
unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Those GPIOs have been deprecated by the pinctrl API. They are unused and
unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The SH73A0 SoC has sparse GPIO numbers. Declare the pin numbers ranges
in the PFC SoC data and use the pin numbers in the GPIO API.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
move r8a7740_meram_workaround() to r8a7740 area
from r8a7779 area
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
R-Car H1 datasheet GIC number is indicating
GIC ICCIAR / interrupt ID number, not SPI number,
but current marzen board code is using gic_spi() with
un-understandable calculation.
This patch adds new gic_iid() macro which means
ICCIAR / interrupt ID, and used the number
currently written on datasheet.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
[ horms+renesas@verge.net.au: Split board-marzen.c portion into a separate patch ]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Each CPU Hotplug implementation for mach-shmobile
is now self-contained, so this change removes unused
helper code in hotplug.c. The two CPU Hotplug capable
SoCs sh73a0 and r8a7779 remain unchanged.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Do not initialise any early devices when using the minimal DT reference
code. Only the delay needs to be initialised.
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Do not initialise any early devices when using the minimal DT reference
code. Only the delay needs to be initialised.
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Update the code in headsmp-scu.S to use a global
shmobile_scu_base variable both for convenient SCU
base address storage and for the early SCU setup
code in shmobile_secondary_vector_scu.
With this patch applied r8a7779, sh73a0 and EMEV2
all make use of the global shmobile_scu_base
variable. However only sh73a0 makes use of the SCU
bring up code in shmobile_secondary_vector_scu.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Rename headsmp-sh73a0.S into headsmp-scu.S and
introduce shmobile_secondary_vector_scu().
The goal is to be able to share the function
above between all mach-shmobile SoCs that use
SCU for SMP. So far only sh73a0 use this.
At this time the SCU base address is still hard
coded in headsmp-scu.S to 0xf0000000, but this
will be changed in the future.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Allow a minimal setup of the r8a7779 SoC using a flattened device tree.
In particular, configure the i2c and ethernet controllers using a
flattened device tree.
SCI serial controller and TMU clock source, whose drivers do not yet
support configuration using a flattened device tree, are still configured
using C code in order to allow booting of a board with this SoC.
The ethernet controller also requires a regulator which is a board property.
A sample snippet DT for the marzen board is as follows:
/dts-v1/;
/include/ "r8a7779.dtsi"
/ {
fixedregulator3v3: fixedregulator@0 {
compatible = "regulator-fixed";
regulator-name = "fixed-3.3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-boot-on;
regulator-always-on;
};
};
&lan0 {
vddvario-supply = <&fixedregulator3v3>;
vdd33a-supply = <&fixedregulator3v3>;
};
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This allows the GIC interrupt controller of the r8a7779 SoC to be
initialised using a flattened device tree blob.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
v3
* Fix copy-paste error and use unique reg values for each CPU
v2
As suggested by Mark Rutland
* Add reg and device_type to cpus
* Remove #address-cells from gic
This is a larger set of new functionality for the existing SoC families,
including:
* vt8500 gains support for new CPU cores, notably the Cortex-A9 based wm8850
* prima2 gains support for the "marco" SoC family, its SMP based cousin
* tegra gains support for the new Tegra4 (Tegra114) family
* socfpga now supports a newer version of the hardware including SMP
* i.mx31 and bcm2835 are now using DT probing for their clocks
* lots of updates for sh-mobile
* OMAP updates for clocks, power management and USB
* i.mx6q and tegra now support cpuidle
* kirkwood now supports PCIe hot plugging
* tegra clock support is updated
* tegra USB PHY probing gets implemented diffently
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=PRrg
-----END PGP SIGNATURE-----
Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC-specific updates from Arnd Bergmann:
"This is a larger set of new functionality for the existing SoC
families, including:
- vt8500 gains support for new CPU cores, notably the Cortex-A9 based
wm8850
- prima2 gains support for the "marco" SoC family, its SMP based
cousin
- tegra gains support for the new Tegra4 (Tegra114) family
- socfpga now supports a newer version of the hardware including SMP
- i.mx31 and bcm2835 are now using DT probing for their clocks
- lots of updates for sh-mobile
- OMAP updates for clocks, power management and USB
- i.mx6q and tegra now support cpuidle
- kirkwood now supports PCIe hot plugging
- tegra clock support is updated
- tegra USB PHY probing gets implemented diffently"
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (148 commits)
ARM: prima2: remove duplicate v7_invalidate_l1
ARM: shmobile: r8a7779: Correct TMU clock support again
ARM: prima2: fix __init section for cpu hotplug
ARM: OMAP: Consolidate OMAP USB-HS platform data (part 3/3)
ARM: OMAP: Consolidate OMAP USB-HS platform data (part 1/3)
arm: socfpga: Add SMP support for actual socfpga harware
arm: Add v7_invalidate_l1 to cache-v7.S
arm: socfpga: Add entries to enable make dtbs socfpga
arm: socfpga: Add new device tree source for actual socfpga HW
ARM: tegra: sort Kconfig selects for Tegra114
ARM: tegra: enable ARCH_REQUIRE_GPIOLIB for Tegra114
ARM: tegra: Fix build error w/ ARCH_TEGRA_114_SOC w/o ARCH_TEGRA_3x_SOC
ARM: tegra: Fix build error for gic update
ARM: tegra: remove empty tegra_smp_init_cpus()
ARM: shmobile: Register ARM architected timer
ARM: MARCO: fix the build issue due to gic-vic-to-irqchip move
ARM: shmobile: r8a7779: Correct TMU clock support
ARM: mxs_defconfig: Select CONFIG_DEVTMPFS_MOUNT
ARM: mxs: decrease mxs_clockevent_device.min_delta_ns to 2 clock cycles
ARM: mxs: use apbx bus clock to drive the timers on timrotv2
...
are unused on ARM architecure. Samsung has some code setting up wdog
in arch_decomp_wdog(). But since CONFIG_S3C_BOOT_WATCHDOG is defined
nowhere, it will not run. Otherwise, system can not boot at all when
wdog is set up but no one pats it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQ9WSiAAoJEFBXWFqHsHzOkpYH/iHOomqWknjg0YjeUKmoqnk+
UnAiP/OD0pOuqdC3izSq5rAaxeCn2ESYhXWdHH3LQFNnhwDPOItagY3T1dBgJH0G
KvO3wDj0K1jUM6Nzt4hta4pnCc/KClyCcVjYrP5pE+bs3NzOzxvfj2tPc81lI0Iy
rnkMLWw6gVRllhecUezt3TOd/GfI7NwuyjjBOLelOerbImWFqLOCNIZSRQlazbyS
hFh4OkR7yoU6vEvPdmS4B4A5PWBHlxiUS6Wr4v+doGFPiFgR05tJodLnnJ/KGWmG
LFY99MyeBvcgiUlFcUpiVLYpWJh+7IB1LJH+IGNJbWFYC+Yvn/o9IRYO8kvuiYE=
=weNJ
-----END PGP SIGNATURE-----
Merge tag 'cleanup-decompwdog-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/cleanup
From Shawn Guo:
The series cleans up ARCH_HAS_DECOMP_WDOG and arch_decomp_wdog which
are unused on ARM architecure. Samsung has some code setting up wdog
in arch_decomp_wdog(). But since CONFIG_S3C_BOOT_WATCHDOG is defined
nowhere, it will not run. Otherwise, system can not boot at all when
wdog is set up but no one pats it.
* tag 'cleanup-decompwdog-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: samsung: remove unused arch_decomp_wdog() code
ARM: remove unused arch_decomp_wdog()
ARM: decompress: remove unused ARCH_HAS_DECOMP_WDOG
Signed-off-by: Olof Johansson <olof@lixom.net>
Method to disable any core to be used on platforms where CPU0 does not
need special treatment.
Signed-off-by: Ulrich Hecht <ulrich.hecht@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Allow a minimal setup of the sh73a0 SoC using a flattened device tree.
In particular, Configure the i2c controllers using a flattened device tree.
SCI serial controller and CMT clock source, whose drivers do not yet
support configuration using a flattened device tree, are still configured
using C code in order to allow booting of a board with this SoC.
*** Please note that the clock initialisation scheme used in
this patch does not currently work with SMP as there
is a yet to be resolved lock-up in workqueue initialisation.
CONFIG_SMP must be disabled when using this code. ***
Includes update from Thierry Reding to no longer use gic_handle_irq()
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
fix
This allows the GIC interrupt controller of the sh73a0 SoC to be
initialised using a flattened device tree blob.
It does not allow the INTC interrupt controller which is also present on
the sh73a0 SoC to be enabled via device tree. Nor does it handle sharing
of interrupts between the GIC and INTC interrupt controllers.
This limits the usefulness of this code to applications which only wish to
access devices which use interrupts that can be handled by the GIC
interrupt controller. Other applications should, for now, continue using
non-device tree initialisation of the sh72a0 interrupt controllers.
Includes update to use irqchip_init() by Thierry Reding
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
When booting secondary CPUs we have used the main CPU to set up the
Snoop Control Unit flags of these CPUs. It is a cleaner approach
if every CPU takes care of its own flags. We avoid the need for
locking and the program logic is more concise. With this patch the file
headsmp-sh73a0.S is added that contains a startup vector for secondary CPUs
that sets up its own SCU flags.
Further in sh73a0_smp_prepare_cpus() we can rely on the generic ARM helper
scu_power_mode(). This is possible as we don't cross borders anymore (every
CPU handles its own flags) and need no locking. So we can throw out the
needless function modify_scu_cpu_psr().
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the lighest possible sleep mode on Cortex-A9 cores: CPU sleep.
It is entered by a simple dsb and wfi instruction via cpu_do_idle(). As
just clocks are stopped there is no need to save or restore any state of
the system.
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Acked-by: Magnus Damm <damm@opensource.se>
[ horms@verge.net.au: Added missing includes ]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the lighest possible sleep mode on Cortex-A9 cores: CPU sleep. It is
entered by a simple dsb and wfi instruction via cpu_do_idle(). As just
clocks are stopped there is no need to save or restore any state of the
system.
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
sh7372_add_early_devices_dt() and sh7372_add_standard_devices_dt() are
defined as global functions in arch/arm/mach-shmobile/setup-sh7372.c,
but their declarations are missing. Add them to common.h, where similar
functions for this and other SoC types are already declared.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms@verge.net.au>
With ARCH_HAS_DECOMP_WDOG removed from arch/arm/boot/compressed/decompress.c,
all the arch_decomp_wdog() definition at platform level is unneeded.
Remmove it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Now that the only field in struct sys_timer is .init, delete the struct,
and replace the machine descriptor .timer field with the initialization
function itself.
This will enable moving timer drivers into drivers/clocksource without
having to place a public prototype of each struct sys_timer object into
include/linux; the intent is to create a single of_clocksource_init()
function that determines which timer driver to initialize by scanning
the device dtree, much like the proposed irqchip_init() at:
http://www.spinics.net/lists/arm-kernel/msg203686.html
Includes mach-omap2 fixes from Igor Grinberg.
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
FSI's external clock is controled by FSI driver.
Global sh7372_fsiXck_clk is no-longer needed now.
But it needs to set external clock rate by platform,
so, this patch supports clk_get() interface.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Not only sh7372 but also many Renesas chip has FSI-DIV clock,
and we can share its sh_clk_ops.
To support common FSI-DIV clock, sh7372_fsidivX_clk
becomes non-global by this patch.
This is preparation for FSI DT support.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
PENCx is Power Enable Control pin for USB.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
SH7372 can use DMA with the FLCTL flash controller. Add required slave
IDs and slave descriptors.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
This is old CPU of shmobile, and the machine by which this CPU is
used cannot be obtained.
Therefore, remove SH7377 support.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
This is old CPU of shmobile, and the machine by which this CPU is
used cannot be obtained.
Therefore, remove SH7367 support.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Patch 35f2b0bd59 "ARM: shmobile: Move definition of shmobile_init_late()
to header" moved the definition of the shmobile_init_late function, but
dropped the __init annotation, which is now causing warnings because
the function calls shmobile_suspend_init, which is also marked init.
Without this patch, building kota2_defconfig results in:
WARNING: vmlinux.o(.text+0xb7c8): Section mismatch in reference from the function shmobile_init_late() to the function .init.text:shmobile_suspend_init()
The function shmobile_init_late() references
the function __init shmobile_suspend_init().
This is often because shmobile_init_late lacks a __init
annotation or the annotation of shmobile_suspend_init is wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Magnus Damm <damm@opensource.se>
Cc: Simon Horman <horms@verge.net.au>
* Improved system suspend/resume and runtime PM handling for the SH TMU, CMT
and MTU2 clock event devices (also used by ARM/shmobile).
* Generic PM domains framework extensions related to cpuidle support and
domain objects lookup using names.
* ARM/shmobile power management updates including improved support for the
SH7372's A4S power domain containing the CPU core.
* cpufreq changes related to AMD CPUs support from Matthew Garrett, Andre
Przywara and Borislav Petkov.
* cpu0 cpufreq driver from Shawn Guo.
* cpufreq governor fixes related to the relaxing of limit from Michal Pecio.
* OMAP cpufreq updates from Axel Lin and Richard Zhao.
* cpuidle ladder governor fixes related to the disabling of states from
Carsten Emde and me.
* Runtime PM core updates related to the interactions with the system suspend
core from Alan Stern and Kevin Hilman.
* Wakeup sources modification allowing more helper functions to be called from
interrupt context from John Stultz and additional diagnostic code from Todd
Poynor.
* System suspend error code path fix from Feng Hong.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=rbCk
-----END PGP SIGNATURE-----
Merge tag 'pm-for-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael J Wysocki:
- Improved system suspend/resume and runtime PM handling for the SH
TMU, CMT and MTU2 clock event devices (also used by ARM/shmobile).
- Generic PM domains framework extensions related to cpuidle support
and domain objects lookup using names.
- ARM/shmobile power management updates including improved support for
the SH7372's A4S power domain containing the CPU core.
- cpufreq changes related to AMD CPUs support from Matthew Garrett,
Andre Przywara and Borislav Petkov.
- cpu0 cpufreq driver from Shawn Guo.
- cpufreq governor fixes related to the relaxing of limit from Michal
Pecio.
- OMAP cpufreq updates from Axel Lin and Richard Zhao.
- cpuidle ladder governor fixes related to the disabling of states from
Carsten Emde and me.
- Runtime PM core updates related to the interactions with the system
suspend core from Alan Stern and Kevin Hilman.
- Wakeup sources modification allowing more helper functions to be
called from interrupt context from John Stultz and additional
diagnostic code from Todd Poynor.
- System suspend error code path fix from Feng Hong.
Fixed up conflicts in cpufreq/powernow-k8 that stemmed from the
workqueue fixes conflicting fairly badly with the removal of support for
hardware P-state chips. The changes were independent but somewhat
intertwined.
* tag 'pm-for-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (76 commits)
Revert "PM QoS: Use spinlock in the per-device PM QoS constraints code"
PM / Runtime: let rpm_resume() succeed if RPM_ACTIVE, even when disabled, v2
cpuidle: rename function name "__cpuidle_register_driver", v2
cpufreq: OMAP: Check IS_ERR() instead of NULL for omap_device_get_by_hwmod_name
cpuidle: remove some empty lines
PM: Prevent runtime suspend during system resume
PM QoS: Use spinlock in the per-device PM QoS constraints code
PM / Sleep: use resume event when call dpm_resume_early
cpuidle / ACPI : move cpuidle_device field out of the acpi_processor_power structure
ACPI / processor: remove pointless variable initialization
ACPI / processor: remove unused function parameter
cpufreq: OMAP: remove loops_per_jiffy recalculate for smp
sections: fix section conflicts in drivers/cpufreq
cpufreq: conservative: update frequency when limits are relaxed
cpufreq / ondemand: update frequency when limits are relaxed
properly __init-annotate pm_sysrq_init()
cpufreq: Add a generic cpufreq-cpu0 driver
PM / OPP: Initialize OPP table from device tree
ARM: add cpufreq transiton notifier to adjust loops_per_jiffy for smp
cpufreq: Remove support for hardware P-state chips from powernow-k8
...
Most platforms don't need mach/gpio.h and it prevents multi-platform
kernel images. Add CONFIG_NEED_MACH_GPIO_H and make platforns select it
if they need gpio.h. This is platforms that define __GPIOLIB_COMPLEX
or have lots of implicit includes pulled in by mach/gpio.h.
at91 and omap have gpio clean-up pending and can drop
CONFIG_NEED_MACH_GPIO_H once that is in.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Move custom shmobile gpio code to a sh-gpio.h to remove the dependency
on mach/gpio.h. shmobile always uses gpiolib, so we can remove
__GPIOLIB_COMPLEX define from mach/gpio.h.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Convert shmobile SMP platforms to use struct smp_operations to provide
their SMP and CPU hotplug operations.
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add a "C5" cpuidle state to the SH7372 SoC connected to the A4S power
domain in such a way that A4S may be turned off by cpuidle if all
I/O devices in that domain have been suspended (or do not have
attached drivers).
This requires some reorganization of the initialization of SH7372
power management which affects the the boards based on it, Mackerel
and AP4EVB.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
The sh7372 cpuidle code uses the same artificially designed routine
shmobile_cpuidle_enter() as the .enter() callback for all of its
cpuidle states. However, shmobile_cpuidle_enter() calls a different
"enter" function for each state using an array of function pointers
populated by the sh7372 PM initialization code. Moreover, the
states[] array of the shmobile cpuidle driver is populated by that
code as well, although in principle it just might have been filled
with static data.
All of that complexity goes away if the sh7372 cpuidle code is
allowed to define its own cpuidle driver structure that can be passed
for registration to the common shmobile cpuidle initialization
routine, so modify the code accordingly.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
The role of the only function in the common.c file in
arch/arm/mach-shmobile, shmobile_init_late(), is to call two
initializers whose definitions depend on kernel configuration
options. Those initializers may very well be called from a static
inline function in arm/mach-shmobile/include/mach/common.h,
though, in which makes the code a bit easier to read. Moreover,
the common.c may be dropped entirely then.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
On SH7372 and Mackerel devices are added to PM domains through a
series of rmobile_add_device_to_domain_td() calls where the last
argument is always the same. This is quite inefficient, so add
a common function for adding devices to PM domains that reads the
domain-device pairs information from a table and use it during SH7372
and Mackerel initialization.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Make it possible to specify device start/stop and save/restore
state latencies directy when adding devices to PM domains. For
this purpose, introduce rmobile_add_device_to_domain_td() whose
third argument is a pointer to a struct gpd_timing_data object
containing device latency data.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Since rmobile_init_pm_domain() is not called anywhere outside of
arch/arm/mach-shmobile/pm-rmobile.c any more, it can be made static
and its header may be removed from pm-rmobile.h. Modify the code
accordingly.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Instead of giving a name to every r8a7779's PM domain object, put
them all into a table and initialize them all together in a loop.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Instead of giving a name to every r8a7740's PM domain object, put
them all into a table and use rmobile_init_domains(), introduced by a
previous patch, for initializing them all altogether. Also, use
pm_genpd_add_subdomain_names() for adding A3SP as a subdomain of A4S.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Instead of giving a name to every sh7372's PM domain object, put them
all into a table and use rmobile_init_domains(), introduced by a
previous patch, for initializing them all altogether. Also, use
pm_genpd_add_subdomain_names() for adding subdomains to the PM
domains and pm_genpd_poweron_name() for turning on the A4S domain
when preparing for system suspend.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Add a new routine, rmobile_init_domains(), allowing the caller
to initialize all generic PM objects stored in a table in one
operation.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Make the power management code under arch/arm/mach-shmobile/
use pm_genpd_add_subdomain_names() for adding subdomains to power
domains, which makes it possible to drop
rmobile_pm_add_subdomain() and will allow us to carry out those
operations for domain objects stored in tables in a straightforward
way.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
If the r8a7779's PM domains are given names, this SoC and its boards
will be able to use rmobile_add_device_to_domain() for adding devices
to those domains and r8a7779_add_device_to_domain(), which is not
used anywhere at the moment anyway, may be dopped.
Accordingly, give names to the r8a7779's PM domains and drop
r8a7779_add_device_to_domain().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Make the power management code under arch/arm/mach-shmobile/ use
names of power domains instead of pointers to domain objects for
adding devices to the domains. This will allow us to put the
domain objects into tables and register them all in one shot
going forward.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
* renesas-sh7372:
ARM: shmobile: Fix build problem in pm-sh7372.c for unusual .config
ARM: shmobile: Take cpuidle dependencies into account correctly
ARM: shmobile: sh7372: completely switch over to using pm-rmobile API
ARM: shmobile: ap4evb: switch to using pm-rmobile API
ARM: shmobile: mackerel: switch to using pm-rmobile API
ARM: shmobile: sh7372: add pm-rmobile domain support
ARM: shmobile: sh7372 A3SM CPUIdle support
ARM: shmobile: Use INTCA with sh7372 A3SM power domain
ARM: shmobile: use common DMAEngine definitions on sh7372
ARM: shmobile: sh7372: remove unused sh7372_a3sp_init() on !CONFIG_PM
* renesas-sh73a0:
ARM: shmobile: use common DMAEngine definitions on sh73a0
ARM: shmobile: sh73a0: add DMAEngine support for MPDMAC
ARM: shmobile: sh73a0: add USB clock support
Now, all sh7372 platforms are switched over to use pm-rmobile base PM domain,
and no one is using original sh7372_pm_domain APIs.
We can remove these, switching has been fully completed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch adds pm-rmobile common API base PM domain.
sh7372 CPU/platform will switch to using it from
original implementation
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch adds basic A4LC pm domain support.
Now, below devices can be controled by PM
MERAM, LCDC, VOU, ICBS, SDENC-Link
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch adds Renesas R-mobile series common PM domain APIs.
R-mobile CPU can use/switch this API
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Current shdmac can support MPDMAC (= sound DMA) on sh73a0.
This support reduce CPU load when sound was playback.
On v2.0 manual, MPDMAC MID/RID number were wrong.
This patch is using the number which seems correct.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Current shdmac can support USB DMAC on r8a7740.
This support reduce CPU duty when USB access.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Current shdmac can support SDHI DMAC on r8a7740.
This support reduce CPU duty when SDHI access.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Current shdmac can support FSI DMAC on r8a7740.
This support reduce CPU duty when sound was playback.
This patch is based on v1.0 manual
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Current shmobile have DMAEngine specific settings on each CPU code,
but SH-ARM DMAC use same value.
This patch adds new dma-register.h header to share definitions
and reduce a waste of code on SH-ARM architecture.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Current gpio frame work doesn't have the method to control
just pull up/down/free, but some SH-ARM boards need such kind of operation.
This patch adds common extra gpio functions for SH-ARM.
But these functions should be replaced by correct
gpio function in the future.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
In order to enable FSI-B selection from platform board,
this patch adds its interface to GPIO framework.
This patch is based on v1.0 manual
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
r8a7740 chip has lasting errata on MERAM buffer, and this patch adds
its work-around on setup-r8a7740.c
It solved CEU/VIO6C/2D-DMAC/VCP1/VPU5F/JPU/DISP memroy access error.
But MERAM driver can't control this issue,
since this work-around requires access to non-MERAM register address.
So, This it will be called as board specific code at this point.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
In order to enable HDMI GPIO selection from platform board,
this patch adds its interface to GPIO framework.
This patch is based on v1.0 manual
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This is a patch series from Shawn Guo that moves from individual
late_initcalls() to using a member in the machine structure to invoke
a platform's late initcalls.
This cleanup is a step in the move towards multiplatform kernels since
it would reduce the need to check for compatible platforms in each and
every initcall.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=21h6
-----END PGP SIGNATURE-----
Merge tag 'cleanup-initcall' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull sweeping late_initcall cleanup for arm-soc from Olof Johansson:
"This is a patch series from Shawn Guo that moves from individual
late_initcalls() to using a member in the machine structure to invoke
a platform's late initcalls.
This cleanup is a step in the move towards multiplatform kernels since
it would reduce the need to check for compatible platforms in each and
every initcall."
Fix up trivial conflicts in arch/arm/mach-{exynos/mach-universal_c210.c,
imx/mach-cpuimx51.c, omap2/board-generic.c} due to changes nearby (and,
in the case of cpuimx51.c the board support being deleted)
* tag 'cleanup-initcall' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: ux500: use machine specific hook for late init
ARM: tegra: use machine specific hook for late init
ARM: shmobile: use machine specific hook for late init
ARM: sa1100: use machine specific hook for late init
ARM: s3c64xx: use machine specific hook for late init
ARM: prima2: use machine specific hook for late init
ARM: pnx4008: use machine specific hook for late init
ARM: omap2: use machine specific hook for late init
ARM: omap1: use machine specific hook for late init
ARM: msm: use machine specific hook for late init
ARM: imx: use machine specific hook for late init
ARM: exynos: use machine specific hook for late init
ARM: ep93xx: use machine specific hook for late init
ARM: davinci: use machine specific hook for late init
ARM: provide a late_initcall hook for platform initialization
While we generally attempt to get rid of board specific files and replace
them with device tree based descriptions, a lot of platforms have not
come that far:
In shmobile, we add two new board files because their recently started
effort to add DT support has not proceeded enough to use it for all of
the important hardware.
In Kirkwood, we are adding support for new boards with a combination of
DT and board file contents in multiple cases.
pxa/mmp and imx are extending support for existing board files but not
adding new ones.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=wkmj
-----END PGP SIGNATURE-----
Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc board specific changes from Olof Johansson:
"While we generally attempt to get rid of board specific files and
replace them with device tree based descriptions, a lot of platforms
have not come that far:
In shmobile, we add two new board files because their recently started
effort to add DT support has not proceeded enough to use it for all of
the important hardware.
In Kirkwood, we are adding support for new boards with a combination
of DT and board file contents in multiple cases.
pxa/mmp and imx are extending support for existing board files but not
adding new ones."
Fix up trivial conflicts in arch/arm/mach-{mmp/ttc_dkb.c,shmobile/{Kconfig,Makefile}}
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (94 commits)
ARM: shmobile: fix smp build
ARM: kirkwood: Add support for RaidSonic IB-NAS6210/6220 using devicetree
kirkwood: Add iconnect support
orion/kirkwood: create a generic function for gpio led blinking
kirkwood/orion: fix orion_gpio_set_blink
ARM: kirkwood: Define DNS-320/DNS-325 NAND in fdt
kirkwood: Allow nand to be configured via. devicetree
mtd: Add orion_nand devicetree bindings
ARM: kirkwood: Basic support for DNS-320 and DNS-325
ARM: mach-shmobile: Use DT_MACHINE for armadillo 800 eva
ARM: mach-shmobile: Use DT_MACHINE for KZM9G
ARM: pxa: hx4700: Add Synaptics NavPoint touchpad
ARM: pxa: Use REGULATOR_SUPPLY macro
ARM: mach-shmobile: kzm9g: enable SMP boot
ARM: mach-shmobile: kzm9g: defconfig update
ARM: mach-shmobile: kzm9g: add PCF8757 gpio-key
ARM: mach-shmobile: kzm9g: add SDHI support
ARM: mach-shmobile: kzm9g: add MMCIF support
ARM: mach-shmobile: kzm9g: correct screen direction
ARM: mach-shmobile: sh73a0.h: add GPIO_NR
...
Tie in the Emma Mobile GPIO driver "em-gio" to
support the GPIOs on Emma Mobile EV2.
A static IRQ range is used to allow boards to
hook up their platform devices to the GPIOs.
DT support is still on the TODO for the GPIO driver,
so only platform device support is included here.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This is V3 of Emma Mobile EV2 SMP support.
At this point only the most basic form of SMP operation
is supported. TWD and CPU Hotplug support is excluded.
Tied to both the Emma Mobile EV2 and the KZM9D board
due to the need to switch on board in platsmp.c and
the newly introduced need for static mappings.
The static mappings are needed to allow hardware
acces early during boot when SMP is initialized.
This early requirement forces us to also map in
the SMU registers.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This is V3 of the Emma Mobile EV2 SoC support.
Included here is support for serial and timer
devices which is just about enough to boot a kernel.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Current IRQ16-IRQ31 irq number are located around 800 from
1ee8299a9e
(ARM: mach-shmobile: Use 0x3400 as INTCS vector offset)
But, the PINT0/1 IRQ number are also located around 800 from
0df1a838d6
(ARM: mach-shmobile: sh73a0 PINT IRQ base fix)
This patch relocates PINT0/1 IRQ number to around 700 where is not used,
and adds current IRQ location table in comment area.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
GPIO_NR is added in order to clarify end of GPIO array.
We can add extra GPIO from it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Fix SMP TWD boot regression on sh73a0 based platforms caused by:
4200b16 ARM: shmobile: convert to twd_local_timer_register() interface
After the merge of the above commit it has been impossible to boot
sh73a0 based SoCs with SMP enabled and CONFIG_HAVE_ARM_TWD=y. The
kernel crashes at smp_init_cpus() timing which is before the console
has been initialized, so to the user this looks like a kernel lock up
without any particular error message.
This patch fixes the regression on sh73a0 by moving the TWD
registration code from smp_init_cpus() to sys_timer->init() time.
This patch removed shmobile_twd_init() which is no longer needed
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Fix SMP TWD boot regression on r8a7779 based platforms caused by:
4200b16 ARM: shmobile: convert to twd_local_timer_register() interface
After the merge of the above commit it has been impossible to boot
r8a7779 based SoCs with SMP enabled and CONFIG_HAVE_ARM_TWD=y. The
kernel crashes at smp_init_cpus() timing which is before the console
has been initialized, so to the user this looks like a kernel lock up
without any particular error message.
This patch fixes the regression on r8a7779 by moving the TWD
registration code from smp_init_cpus() to sys_timer->init() time.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Update mach-shmobile to use 0x3400 as INTCS_VECT_BASE.
Since the ARM architecture a little while back added support
for 10 bit irqs we can now undo the previously merged commit
9b7c23adb3 and use 0x3400 as
INTCS vector base.
This change is necessary to avoid overlapping of interrupt
ranges so separate IRQ domains can be used for different INTC
instances. Without this fix the vectors used by various INTC
instances are overlapping on for instance sh7372 which works
at the moment but breaks upcoming IRQ domain support.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Add INTC_IRQ_PINS_16H to allow broken out support of the
the high 16 external interrupt pins. On SoCs with 32 external
interrupt pins the interrupt vectors for the low 16 and the
high 16 interrupt pins are sparesly populated. The low 16 are
at 0x0200 and high 16 are at 0x3200 which with current macros
results in a separation of 384 linux interrupts. This sparse
population makes it unsuitable with a single IRQ domain to
cover the full IRQ range, so this macro breaks out the 32 pins
into two separate 16 bit controllers to allow two independent
INTC instances with two separate IRQ domains.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Add the function shmobile_setup_delay() to let platforms
configure their maximum loops per jiffy delay. With this
jiffies calculation done the dependency on early timer
is removed.
In the future this allows us to assign timers
using the regular driver model via the device tree.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Rob Herring has done a sweeping change cleaning up all of the mach/io.h includes,
moving some of the oft-repeated macros to a common location and removing a bunch of
boiler plate. This is another step closer to a common zImage for multiple platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=YIsn
-----END PGP SIGNATURE-----
Merge tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: cleanups of io includes" from Olof Johansson:
"Rob Herring has done a sweeping change cleaning up all of the
mach/io.h includes, moving some of the oft-repeated macros to a common
location and removing a bunch of boiler plate. This is another step
closer to a common zImage for multiple platforms."
Fix up various fairly trivial conflicts (<mach/io.h> removal vs changes
around it, tegra localtimer.o is *still* gone, yadda-yadda).
* tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (29 commits)
ARM: tegra: Include assembler.h in sleep.S to fix build break
ARM: pxa: use common IOMEM definition
ARM: dma-mapping: convert ARCH_HAS_DMA_SET_COHERENT_MASK to kconfig symbol
ARM: __io abuse cleanup
ARM: create a common IOMEM definition
ARM: iop13xx: fix missing declaration of iop13xx_init_early
ARM: fix ioremap/iounmap for !CONFIG_MMU
ARM: kill off __mem_pci
ARM: remove bunch of now unused mach/io.h files
ARM: make mach/io.h include optional
ARM: clps711x: remove unneeded include of mach/io.h
ARM: dove: add explicit include of dove.h to addr-map.c
ARM: at91: add explicit include of hardware.h to uncompressor
ARM: ep93xx: clean-up mach/io.h
ARM: tegra: clean-up mach/io.h
ARM: orion5x: clean-up mach/io.h
ARM: davinci: remove unneeded mach/io.h include
[media] davinci: remove includes of mach/io.h
ARM: OMAP: Remove remaining includes for mach/io.h
ARM: msm: clean-up mach/io.h
...
Pull more ARM updates from Russell King.
This got a fair number of conflicts with the <asm/system.h> split, but
also with some other sparse-irq and header file include cleanups. They
all looked pretty trivial, though.
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (59 commits)
ARM: fix Kconfig warning for HAVE_BPF_JIT
ARM: 7361/1: provide XIP_VIRT_ADDR for no-MMU builds
ARM: 7349/1: integrator: convert to sparse irqs
ARM: 7259/3: net: JIT compiler for packet filters
ARM: 7334/1: add jump label support
ARM: 7333/2: jump label: detect %c support for ARM
ARM: 7338/1: add support for early console output via semihosting
ARM: use set_current_blocked() and block_sigmask()
ARM: exec: remove redundant set_fs(USER_DS)
ARM: 7332/1: extract out code patch function from kprobes
ARM: 7331/1: extract out insn generation code from ftrace
ARM: 7330/1: ftrace: use canonical Thumb-2 wide instruction format
ARM: 7351/1: ftrace: remove useless memory checks
ARM: 7316/1: kexec: EOI active and mask all interrupts in kexec crash path
ARM: Versatile Express: add NO_IOPORT
ARM: get rid of asm/irq.h in asm/prom.h
ARM: 7319/1: Print debug info for SIGBUS in user faults
ARM: 7318/1: gic: refactor irq_start assignment
ARM: 7317/1: irq: avoid NULL check in for_each_irq_desc loop
ARM: 7315/1: perf: add support for the Cortex-A7 PMU
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G9mT
-----END PGP SIGNATURE-----
Merge tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system
Pull "Disintegrate and delete asm/system.h" from David Howells:
"Here are a bunch of patches to disintegrate asm/system.h into a set of
separate bits to relieve the problem of circular inclusion
dependencies.
I've built all the working defconfigs from all the arches that I can
and made sure that they don't break.
The reason for these patches is that I recently encountered a circular
dependency problem that came about when I produced some patches to
optimise get_order() by rewriting it to use ilog2().
This uses bitops - and on the SH arch asm/bitops.h drags in
asm-generic/get_order.h by a circuituous route involving asm/system.h.
The main difficulty seems to be asm/system.h. It holds a number of
low level bits with no/few dependencies that are commonly used (eg.
memory barriers) and a number of bits with more dependencies that
aren't used in many places (eg. switch_to()).
These patches break asm/system.h up into the following core pieces:
(1) asm/barrier.h
Move memory barriers here. This already done for MIPS and Alpha.
(2) asm/switch_to.h
Move switch_to() and related stuff here.
(3) asm/exec.h
Move arch_align_stack() here. Other process execution related bits
could perhaps go here from asm/processor.h.
(4) asm/cmpxchg.h
Move xchg() and cmpxchg() here as they're full word atomic ops and
frequently used by atomic_xchg() and atomic_cmpxchg().
(5) asm/bug.h
Move die() and related bits.
(6) asm/auxvec.h
Move AT_VECTOR_SIZE_ARCH here.
Other arch headers are created as needed on a per-arch basis."
Fixed up some conflicts from other header file cleanups and moving code
around that has happened in the meantime, so David's testing is somewhat
weakened by that. We'll find out anything that got broken and fix it..
* tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system: (38 commits)
Delete all instances of asm/system.h
Remove all #inclusions of asm/system.h
Add #includes needed to permit the removal of asm/system.h
Move all declarations of free_initmem() to linux/mm.h
Disintegrate asm/system.h for OpenRISC
Split arch_align_stack() out from asm-generic/system.h
Split the switch_to() wrapper out of asm-generic/system.h
Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h
Create asm-generic/barrier.h
Make asm-generic/cmpxchg.h #include asm-generic/cmpxchg-local.h
Disintegrate asm/system.h for Xtensa
Disintegrate asm/system.h for Unicore32 [based on ver #3, changed by gxt]
Disintegrate asm/system.h for Tile
Disintegrate asm/system.h for Sparc
Disintegrate asm/system.h for SH
Disintegrate asm/system.h for Score
Disintegrate asm/system.h for S390
Disintegrate asm/system.h for PowerPC
Disintegrate asm/system.h for PA-RISC
Disintegrate asm/system.h for MN10300
...
Disintegrate asm/system.h for ARM.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Russell King <linux@arm.linux.org.uk>
cc: linux-arm-kernel@lists.infradead.org
Conflicts:
arch/arm/mach-tegra/Makefile
arch/arm/mach-vexpress/core.h
The tegra Makefile was changed in four different branches
in the same line. This merge should reduce the amount
of churn.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
arch/arm/mach-shmobile/timer.c
This resolves a nonobvious merge conflict between renesas
timer changes in the global timer changes with those
from the renesas soc branch and last minute bug fixes that
went into v3.3.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add support for the new smp_twd runtime registration interface
to the shmobile platforms, and remove the old compile-time support.
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add shmobile_earlytimer_init() that can be used to
enable the earlytimer probing from the SoC code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Rename clk_init() to shmobile_clk_init() to avoid a potential
future name space collision with the common clock framework.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Update the r8a7779 SoC and the Marzen board to make use of
the functions r8a7779_map_io() and r8a7779_add_early_devices().
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Update the r8a7740 SoC and the Bonito board to make use of
the functions r8a7740_map_io() and r8a7740_add_early_devices().
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Update the sh73a0 SoC and the AG5EVM and Kota2 boards to make use
of the functions sh73a0_map_io() and sh73a0_add_early_devices().
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Kuninori Morimoto