Re-use the "tps65218_pmic_*_current_limit()" functions of LS3
and calculate the different required bit-shift by counting the
trailing 0s in "struct regulator_desc.csel_mask"
Signed-off-by: Christian Hohnstaedt <Christian.Hohnstaedt@wago.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These options apply to all regulators in this chip.
ti,strict-supply-voltage-supervision:
Set STRICT flag in CONFIG1
ti,under-voltage-limit-microvolt:
Select 2.75, 2.95, 3.25 or 3.35 V UVLO in CONFIG1
ti,under-voltage-hyst-microvolt:
Select 200mV or 400mV UVLOHYS in CONFIG2
Signed-off-by: Christian Hohnstaedt <Christian.Hohnstaedt@wago.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Commit 2dc4940360 ("regulator: tps65218: Remove all the compatibles")
changes the probe function of drivers/regulator/tps65218-regulator.c so
that it iterates through all available regulators and assumes that the
regulator IDs are sequential and match the order present in the enum
tps65218_regulator_id. However, for some reason the much older commit
c0ea88b890 ("regulator: tps65218: add support for LS3 current
regulator") updated all arrays with LS3 at the end but added it second
to last for the enum.
Because of this long standing mismatch in order between the
tps65218_regulator_id enum and the regulator_desc array in the tps65218
regulator driver, the new probe function causes the strobe values to be
associated with the wrong regulator ID. This causes LDO1 to fail to
suspend in tps65218_pmic_set_suspend_disable due to not having anything
probes for its strobe value. Fix the order in the enum so the probe
function works as the update intended.
Fixes: 2dc4940360 ("regulator: tps65218: Remove all the compatibles")
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove all the individual compatibles for all the regulators
and introduce id_table and update the driver accordingly
to parse device tree nodes using the regulator framework.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently read directly calls the repmap read function. Hence
remove the redundant wrapper and use regmap read wherever
needed.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some versions of tps65218 do not seem to support poweroff modes properly
if DCDC3 regulator is shut-down. Thus, keep it enabled even during
poweroff if the version info matches the broken silicon revision.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Version information will be needed to handle some error cases under the
regulator driver, so store the information once during MFD probe.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
TPS65218 has a pre-defined power-up / power-down sequence which in
a typical application does not need to be changed. However, it is possible
to define custom sequences under I2C control. The power-up sequence is
defined by strobes and delay times. Each output rail is assigned to a
strobe to determine the order in which the rails are enabled.
Every regulator has sequence registers and every regulator has a default
strobe value and gets disabled when a particular power down sequence
occurs.
To keep a regulator on during suspend we write value 0 to strobe so
that the regulator is out of all sequencers and is not impacted by any
power down sequence. Hence saving the default strobe value during probe
so that when we want to regulator to be enabled during suspend we write 0
to strobe and when we want it to get disabled during suspend we write
the default saved strobe value.
This allows platform data to specify which power rails should be on or off
during RTC only suspend. This is necessary to keep DDR state while in RTC
only suspend.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for TPS65218 LS3 current regulator, which is capable of 4
current input limit modes: 100, 200, 500, and 1000 uA.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Mark Brown <broonie@kernel.org>
The *rdev[] is not used since commit 413be59e2f
"regulator: tps65218: Remove unnecessary regulator_unregister call".
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The TPS65218 chip is a power management IC for Portable Navigation Systems
and Tablet Computing devices. It contains the following components:
- Regulators.
- Over Temperature warning and Shut down.
This patch adds support for tps65218 mfd device. At this time only
the regulator functionality is made available.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Linus Torvalds